Home

FirstAlert FA162C - Protectron Security Systems

1. For Fields 43 44 45 and 46 Enter digits 0 9 11 B 12 C 4 13 D 14 E or 15 F Enter X as the fourth digit if a 3 digit account number for 3 1 dialer reporting format is used Enter 0 as the first digit of a 4 digit account number for Nos 0000 0999 Exit field by pressing and press next field number if only 3 digits are used To clear entries from field press 43 44 45 or 46 See blank Programming Form for examples of Account No entries If using the paging feature do not enter a leading 0 in the subscriber account number and do not use digits A F anywhere in the number Some paging systems provide voice mail capability which is activated by a leading 0 in the message 40 41 42 43 44 45 46 47 48 PABX ACCESS CODE See Box at Left I to ot I Enter up to 6 digits if PABX is needed to access an outside line If fewer than 6 digits are needed to be entered exit by pressing and next field number e g 41 To clear entries from field press 40 PRIMARY PHONE No See Box at Left ENE N te bt te tt te Enter up to 16 digits If fewer than 16 digits entered exit by pressing and next field number e g 42 To clear entries from field press 41 Note Back up reporting 8 calls are made to the secondary phone number if no kiss off is received after 8 attempts to the primary number is automatic only if
2. TERMINALS ANSWERING f 24 EARTH GROUND ON CONTROL EEN La La ON E HABEAS 28 REFER TO He E AAV MODULE 219 S INSTRUCTIONS dis g FOR CONNECTIONS e TO AUDIO SPEAKERS AND MICROPHONE SI 9 Sie We Sie a Se SE TIP TO TERM 21 RELAY MODULE o 13 V a GND 14 E VDC Es NOTE AP 15_ GND DO NOT USE 16 RELAY 1 FOR ANY OTHER RELAY 1 SHOWN pees PURPOSE NONG C 2 3 Figure 21 Connection Of AAV Unit When Also Using A FA4285 Phone Module 40 Section 12 FINAL POWER UP This section provides information about final power up procedures and battery size calculations Earth Ground Connections The designated earth ground terminal 25 must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective It also must be grounded to enable the telephone line fault indicator to work properly The following are examples of good earth grounds available at most installations Metal Cold Water Pipe Use a non corrosive metal strap copper is recommended firmly secured to the pipe to which the ground lead is electrically connected and secured AC Power Outlet Ground Available from 3 prong 120VAC power outlets only To test the integrity of the ground terminal use a three wire circuit tester with neon lamp indicators such as the UL Listed I
3. 51 TAA DEE 91 2 digit phone code iese RA RA RA RA 35 O EE ER AE N EE ER 91 A ER EE AS EE ee 91 RE DER BE EE ORE 91 DO EN OE OE ET OE EN OR EN 91 ARIE LR ER EE EE 91 EE EA EE OE 46 7720 PLUS or 7820 snn ee ae AA Re ee 9 38 24 hour Audible Alarm sees sesse see ee Re 46 NC EE 19 91 24 hour Silent Alarm i e esse ee AR AA Re 46 VEL ED N EE T 91 AC Loss Report Code cocooooccnooccnononnnnnonnnnonnnnonnoncnonnnonanoss 53 A NS RE 91 AC Power Supply imac dd dit 9 DAL a tia lios eiii 91 AC Restore Report Code sesse se RA ER 54 A H KEE 19 91 AC Transformer recostado deis 12 ra EA EE EG DE 91 addressable keypads esse RA 14 15 32 KN MH RE 91 Ademco TA iia iii 36 3 1 and 4 1 Expanded Formats sesse sesse ee eke ee 77 Ademco dadas 336 3 1 and 4 1 Standard Formats iese sesse ese ee 77 Ademco 41 gt ao 36 3 1 or 4 1 Standard Format esse esse esse ee 52 Ademco AB 12M 10 Motorized Bell Box 36 B digithumber secesia 66 67 Ademco Contact ID o ooooooncccnnococononacoonnncnoncncnonononononos 9 77 EE vet AE OE OE EE OD AS 77 Ademco EXDresS esse sesse ee ee ee Re Re sariren 9 89 4 wire smoke detectors i esse ss ee ee RA RA 17 Ademco Low Speed ee RR Re 9 89 AT N EE N 7 14 89 ALARM BELL TIMEOUT eee sesse sesse esse se ee see ee ee 49 AVS TAD EG SEE Ee ER Ee ee Ge bs 7 14 15 89 Ee HE GE 9 37 42 4142 TR cable si ER EES aii lios 13 31 Alarm Restore
4. PHONE MODULE ACCESS CODE 1 9 first digit of access code or second digit of access code enter 11 for or 12 for The use of a FA4285 Phone Module can be used in Partition 1 only requires a 2 digit code Example If desired access code is 7 7 is the first entry and 11 for is the second entry NOTE A 0 in either digit disables the Phone Module OUTPUT TO LONG RANGE RADIO No 7720PLUS 7820 0 If output to LRR is selected here all messages that are programmed to go to the primary telephone line receiver will also be sent to the 7720 PLUS or 7820 radio These messages will always be in Contact ID format not affected by entry in field 48 The data line is supervised as well as certain functions in the radio If communication is lost or a trouble develops a message will be attempted to be sent via both radio and telephone to the central station Note Normal trouble restore report 71 is sent on restore of the condition Entry is first digit of Trouble Dialer Report enter Trouble code 1 9 B 11 C 4 12 D 13 E 4 14 or F 15 The 2nd digit of Trouble Dialer Report is automatically the 2nd digit from field 60 UL installations must be 0 Long Range Radio disabled Note The Radio should be programmed for device address 3 on the keypad lines SINGLE ALARM SOUNDING PER ZONE per armed period 0 0 no limit on alarm sounding per zone
5. BER Section 4 BASIC HARD WIRED ZONES 1 8 This section provides general information for the hard wired zones in the system plus specific instructions for installing 2 wire smoke detectors 4 wire smoke combustion detectors and 2 wire latching type glass break detectors Installing the Hard Wired Zones Common Characteristics for Zones 1 8 e Can be assigned to any partition e EOLR supervised zones supporting both open circuit and closed circuit devices e As many 4 wire smoke detectors as can be powered from Aux Power on the control zones 2 7 e Programmable for 10 350 or 700 msec response e 350 msec default should be used for most standard contacts For vibration type contacts 10 msec is more suitable Wiring Burglary and Panic Devices To Zones 1 8 1 Connect sensors contacts to the hard wired zone terminals 8 through 20 See the Summary of Connections diagram 2 Connect closed circuit devices in series in the high side the loop The EOL resistor must be connected in series with the devices following the last device See the Summary of Connections diagram 3 Connect open circuit devices in parallel across the loop The 2 000 ohm EOLR must be connected across the loop wires at the last device If the EOLR is not at the end of the loop the zone will not be properly supervised and the system may not respond to an open circuit on the zone xh High Resistance Supervision on Hard Wired Zones 2 8 e Special su
6. General Information The FA162C can be remotely programmed from an IBM compatible Personal Computer PC a HAYES Modem and First Alert Professional FADL Software as specified below UL Downloading may only be performed if a technician is at the site Programming the control from a remote location is protected against compromise by someone attempting to defeat the system using multi levels of security protection 1 Security Code Handshake An 8 digit download ID code must be matched between the control and the downloader 2 Site Initiated Remote Programming The installer or subscriber initiates the callback from the subscriber premises by entering Installer code 1 while disarmed All parameters can then be downloaded via the phone lines using a personal computer 3 Station Initiated Remote Programming The operator calls the site from your office to initiate the download call The control hangs up and then calls back the PC via the preprogrammed telephone number The unit can then be uploaded downloaded or controlled from your office 4 Telco Hand off Allows the installer or subscriber to perform a download session on the call initiated from the site 5 Data Encryption Data passed between the PC and the control is encrypted for security so that it is very difficult for a foreign device tapped into the phone line to take over communication and substitute system compromising information Equip
7. 1 Temporarily connect a 2000 ohm end of line resistor across each of the basic hard wire zones 1 8 as shown in the Summary of Connections diagram Without actual zone wiring or EOL resistors connected the keypads in each partition of the system will not display the Ready message 2 Power up the system temporarily by plugging the AC transformer previously wired to the control into a 120VAC outlet 3 Busy Standby Alpha keypads or dl Fixed word keypads will be displayed After approximately 1 minute the green READY LED or POWER LED on some types of keypads should light and the word READY Fixed word keypads or DISARMED READY TO ARM Alpha keypads should be displayed To bypass the 1 minute delay press plus 0 If the Ready display does not appear on any of the keypads in the system in either of the partitions or a Not Ready message is displayed check the keypad wiring connections and make sure each of the 8 basic hard wired zones has a 2000 ohm resistor connected across its terminals 4 When you get the proper Ready displays on the keypad s the system is functioning properly at this point Do not remove the EOL resistors until you are ready to make connections to the hard wired zones to allow for testing later in the manual sd If an OC or OPEN CIRCUIT is present on the keypad data from the control is not reaching the keypad Please check the wiring
8. FA4285 PHONE MODULE see ese esse sees ee sae ese ese ese nono nono ee Gee cnn deed cnn ee ee se ee se ee ee dee 32 Installing the Phone Module 32 General Id e a eas 32 Mounting The Phone Module 32 Phone Module Wiring st Ese ESSEN Ge EKKE Se KEN sea RSG ER ALEN EN E ERA NAAA idas 33 Caller ID De EE 33 Checking the Operation of the FA4285 Phone Module 35 EXTERNAL SOUNDERS c et do Eeer cies dl 36 Compatible arnes A da Dee 36 A SE O via eds 37 Testine the Sunder sirs a NN 37 LONG RANGE RADIO eet n ss des ee ee ita a SE a i n AD E aT 38 General Ind MaAtiIIM e na se EE eek ek TA ee ENARA 38 CONNECTION EE 38 AUDIO ALARM VERIFICATION AAV UNIT A 39 General Information ode into oe Sta Den od EE tion suas 39 Wiring Connections ii ee naaa 39 FINAL POWER UP EE 41 Earth Ground Connections cccocoocccnononnnonnnonnnono Ge AA ee AA ER ee AR ee ARRENAR AA ee nana EEE Ge 41 Connecting the Back Up Batter 41 Calculating the Battery Size Needed iese ee se ee ER AR AR AR AA 41 Making the Battery Connections ccoooooconooooncnnnoonnnnon Re AR Re AA AR Re AA GR ee Ge nn ee ee Re cnn ee 42 Auxiliary Device Current Draw Worksheet cooooooninoccccnooocccnono see ee RA AR RA Se ee ee conos 42 MECHANICS OF PROGRAMMING AAA 43 General Programming Information cccnooccncnononnnnnonnnn Ge RA ee AA Ge RA Ge AR Ge Se ee Se ee 43 Entering Program Mode A a ae De Se 43 Programming a Data Field 43 Reviewing a Data Field Erasing an Entry
9. In addition the connection to the battery is checked every 3 minutes CSFM requirement If there is no battery detected or a low battery condition detected a low battery message is displayed and a report is sent to the central station AUXILIARY DEVICE CURRENT DRAW WORKSHEET ams soma DEET FASSOKP Keypad ga FASSOKP amp FASSORPR Ged Keypad oes ees Rewer ssa 4219 Zone Expander et Lena asomar 4229 Zone Boude Ua Leg Jl og Phone Module em TOTAL Current available from Aux terminals 600 mA max Tf using hard wire devices such as PIRs refer to the specifications for that particular unit s current draw Tn UL installations maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 700 mA 600 mA max from Auxiliary Output D Figures are for relays OFF relays ON 42 Section 13 MECHANICS OF PROGRAMMING This section provides information on how to use the system s programming modes It will enable you to understand how to enter and exit programming mode and how to program the data fields and how to use the user friendly interactive modes 56 80 81 82 83 If RF zones or wired expansion will be used the following program fields AL must be programmed as required before doing any zone programming 22 RF SYSTEM 25 WIRED ZONE EXPANSION General Programming Information Characteristics for each installation are store
10. 1 limit alarm sounding to once per arming period for a given zone UL installations must be 0 no limit FIRE SOUNDER TIMEOUT 0 0 yes fire sounder timeout after time programmed in field 33 1 no fire sounder timeout continue sounding until manually turned off This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances Temporal pulse sounding for a fire alarm consists of the following 3 pulses pause 3 pulses pause 3 pulses 48 33 34 35 36 37 38 39 ALARM BELL TIMEOUT 1 0 No timeout 1 4 min 2 8 min 3 12 min 4 16 min This field determines whether the external sounder will shut off after time allotted or continue until manually turned off UL installations must be set for a minimum of 4 min option 1 EXIT DELAY 710 710 00 99 exit delay time for each partition in seconds The system will wait the time entered before sounding an alarm if the exit door is left opened after the system has been armed ENTRY DELAY 01 310 310 00 99 entry delay time for each partition in secs Part 1 Part 2 The system will wait the time entered before sounding alarm upon entering UL installations must be set for a maximum of 20 seconds ENTRY DELAY 02 610 610 00 99 entry delay time for each partition in secs Part 1 Part 2 The system will wait the tim
11. 7720 PLUS or 7820 Long Range Radio to the control s keypad connection points terminals 4 5 6 and 7 as shown below Gi BLACK Eb 7720 PLUS 7820 LONG RANGE RADIO GREEN CONTROL DATA IN RADIO DATA OUT YELLOW CONTROL DATA OUT RADIO DATA IN CONTROL TERMINALS Figure 18 Long Range Radio Connections 38 Section 11 AUDIO ALARM VERIFICATION AAV UNIT General Information An Audio Alarm Verification AAV module such as the Eagle 1241 is an add on accessory that permits voice dialog between an operator at a central station and a person at the alarm installation for the purpose of alarm verification In addition to entering option 4 in field 91 OPTION SELECTION gs Contact ID report format must be selected for the primary phone number and alarm reports must be programmed for the primary phone number to enable the AAV feature U L The AAV option cannot be used in UL installations After all messages have been sent during a reporting session to the primary phone number the control will trigger the AAV if at least one of the messages was an alarm report The control will send a listen in to follow message Contact ID event code 606 which signals the 685 to hold the phone connection for 1 minute Once the digital message is kissed off the control will give up the phone line to the AAV module without breaking connection with the central station At this time all sirens
12. A SSS S A SSSS AZ AAA A Z Trouble SSS S T SSS S T SSSS Tt TTT T t Bypass SSS S B SSS S B SSSS Bb BBB B b AC Loss SSS S E SSS S E SSSS EAC EEK E Ac Low Batt SSS S L SSS S L SSSS LLp LLL L Lp Open SSS S O SSS S O SSSS OU 000 0 U Close SSS S C SSS S C SSSS CU CCC C U Test SSS S G SSS S G SSSS Gg GGG G g Restore SSS S R SSS S R SSSS RZ Alarm RRR R Z AC Restore SSS S R A SSS S RA SSSSRa Ae RARARARAAc LoBat Res SSS S RL SSS S RL SSSS RLB RLRLRLRLULRB Trouble Res SSS S Ry SSS S Rm SSSS Ryt RTRTRT Rpt Bypass Res SSS S Rp SSS S Rp SSSS Rpb RpRpRp R Bb Where SSS or SSSS Subscriber ID C Close Code 1st Digit A Alarm Code 1st digit U User Number in hex Z Typically Zone Number 2nd digit g Test Code 1st amp 2nd digits Tt Trouble Code 1st amp 2nd digits R Restore Code Alarm Bb Bypass Code 1st amp 2nd digits Ryt Restore Code Trbl 1st 8 2nd digits EAc AC Loss Code 1st amp 2nd digits Rgb Restore Code Byps 1st amp 2nd digits LLg Low Battery Code 1st amp 2nd digits RaAc Restore Code AC 1st amp 2nd digits O Open Code 1st Digit RLLB Restore Code Bat 1st amp 2nd digits Zone numbers for x amp or B 99 1 x or A 95 Duress 92 3 4 or C 96 Tamper 9 77 Ademco Contact ID Reporting takes the following format CCCC Q EEE GG ZZZ where CCCC Customer subscriber ID Q Event qualifier where E new event and R
13. Battery 8A No 90 12 3 Communication FORMATS SUPPORTED Ademco Express 10 characters sec DTMF TouchTone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF Ademco Contact ID Reporting 10 characters sec DTMF TouchTone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF Ademco Low Speed 10 pulses sec 1900Hz Data Tone 1400Hz ACK KISSOFF Radionics SESCOA 20 pulses sec 1800Hz Data Tone 2300Hz ACK KISSOFF Can report 0 9 Bb Line Seize Double Pole Ringer Equivalence 0 7B FCC Registration No AC 398U 68192 AL E 4 Maximum Zone Resistance Zones 1 8 300 ohms excluding EOLR FA210KP 1 Physical 5 3 4 W x 4 3 4 Hx1 D 146mm x 121mm x 26mm REMOTE KEYPAD 2 Electrical Voltage Input 12VDC Current Drain 30mA FA250KP 1 Physical 5 1 16 W x 6 3 8 H x 1 3 4 D 129mm x 162mm x 45mm REMOTE KEYPAD 2 Electrical Voltage Input 12VDC Current Drain 120mA FA450KP FA550KP 1 Physical 5 1 16 W x 6 3 8 H x 1 3 4 D 129mm x 162mm x 45mm REMOTE KEYPADS 2 Electrical Voltage Input 12VDC Current Drain 140mA 89 5881 5882 SERIES RF RECEIVERS 5800 System 5800TM TRANSMITTER MODULE used with 5827BD Wireless 2 Way Keypad 4219 WIRED EXPANSION MODULE 4204 RELAY MODULE 4229 WIRED EXPANSION RELAY MODULE FA4285 PHONE MODULE gt A COD 7 3 8 188mm W x 4 3 8 112mm H x 1 7 16 87mm D Note 10 7 8 277mm H with antenna Electrical Voltage Input 12VDC Current Drain 35mA Range
14. alarm warning devices however loud may not warn hearing impaired people Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service Telephone lines are also subject to compromise by sophisticated intruders Even if the system responds to the emergency as intended however occupants may have insufficient time to protect themselves from the emergency situation In the case of a monitored alarm system authorities may not respond appropriately This equipment like other electrical devices is subject to component failure Even though this equipment is designed to last as long as 20 years the electronic components could fail at any time The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance This alarm system should be tested weekly to make sure all sensors and transmitters are working properly The security keypad and remote keypad should be tested as well Wireless transmitters used in some systems are designed to provide long battery life under normal operating conditions Longevity of batteries may be as much as 4 to 7 years depending on the environment usage and the specific wireless device being used External factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation This wireless system howe
15. e Connect all detectors in parallel across zone 8 terminals 19 and 20 S You must connect the EOL resistor across the loop wires at the last detector Remove 2000 ohm EOL resistor if connected across the selected zone terminals Compatible Glass Break Detectors Use detectors that meet the following ratings Standby Voltage 5VDC 18 8VDC Standby Resistance Greater than 20k ohms equivalent resistance of all detectors in parallel Alarm Resistance Less than 1 1k ohms see note below Alarm Current 2 mA 10 mA Reset Time Less than 6 seconds The IEI 735L series detectors have been tested and found to be compatible with these ratings You can use up to fifty IEI 735L detectors connected in parallel You should note that only one detector in the alarmed state can be supported by the alarm current provided by zone 8 You can use detectors which exceed 1 1k ohms in alarm provided they maintain a voltage drop in alarm of less than 3 8 volts Do not use other N O or N C contacts when using glass break detectors on zone 8 Other contacts may prevent proper glass break detector operation GLASSBREAK DETECTOR 2000 LATCHING TYPE GLASS OHMS EOLR BREAK DETECTOR LOOP Figure 10 Glass Break Detector Connections To Zone 8 BER Programming Hard Wired Zones Each zone must be programmed into the system using the 56 Zone Programming mode which assigns ch
16. it seizes the line from the premises phones and any answering machines Note The phone lines must be in service for the phone module to function even when accessing the system from an on premises phone 1 Make 12V and and data in and data out connections from the Phone Module to the control using the connector cable supplied with the Phone Module see Figure 16 Color Lead Terminal On Control These are the same GREEN DATA IN terminal 6 pen E SE used for remote keypads BLACK AUX terminal 4 connected to Partition 1 RED AUX terminal 5 YELLOW DATA OUT terminal 7 2 Insert the keyed connector at the other end of the connector cable into the mating header on the Phone Module see diagram on next page for location of the header 3 Connect terminals 1 through 5 on the Phone Module as shown in the Wiring Table below and in the FA4285 wiring diagram that follows Use an RJ31X jack with a direct connect cord and make all connections exactly as shown If the leads on the direct connect cord are too short to reach their assigned terminals splice additional wires to them as required FA4285 WIRING TABLE Earth ground terminal 25 on control If no touch tones are produced following access to the security system from oe on premises this problem may arise in rare cases it may be necessary to reverse the wires connected to terminals 3 and 4 on the Phone Module and
17. off Mount the receiver The RF receiver can detect signals from transmitters within a nominal range of 200 feet Take this into consideration when determining mounting location Connect the receiver s wire harness to the control s keypad terminals 4 5 6 and 7 Plug the connector at the other end of the harness into the receiver Refer to the installation instructions provided with the receiver for further installation procedures regarding antenna mounting etc NOTE CIRCUIT BOARD IS MOUNTED IN CONTROL S CABINET GROUNDING LUGS 2 PROVIDED MUST BE INSERTED IN LEFT L HAND TERMINALS OF ANTENNA BLOCKS AND ANTENNAS MODEL No IS INDICATED SECURED TO CABINET SEE RECEIVER S INSERT IN ON CIRCUIT BOARD AND CONTROL S INSTRUCTIONS RIGHT HAND TERMINALS YELLOW RED BLACK TO CONTROLS E GREEN REMOTE KEYPAD CIRCUIT L 4 LOCATION CONNECTION PL BOARD D WIRING POINTS MOUNTING Cc OPENING INTERFERENCE DIP SWITCH HOLES INDICATOR KNOCKOUT AREA FOR SURFACE WIRING TO RELEASE CIRCUIT BOARD REMOVE SCREWS 2 AND BEND BACK TABS 2 Figure 12 5881 5882 RF Receiver cover removed 24 Installing the 5800TM Module Installation of this module is necessary only if you are using one or more 5827BD Wireless Bi directional keypads or a 5804BD transmitter Note The 5827BD and 5804BD will only receive signals for partition 1 Mounting the 5800TM Module The 5800TM must be located next to the RF receiver between one and two
18. zone number s Forced Quick Bypass To automatically bypass all faulted zones plus If enabled zones 17 30 and 31 if programmed use the Quick Bypass method Enter code BYPASS then wait for all open zones to be displayed Arm when display indicates bypass and ready to arm Chime Mode Enter code CHIME 9 To turn chime off enter code CHIME again SUMMARY OF ARMING MODES Features for Each Arming Mode Arming Exit Entry Perimeter Interior Mode elay elay mes i AWAY STAY O SE E A INSTANT Yes No Ys No MAXIMUM e No Ys Ys In a 2 partition system if the same master code is in effect for both partitions both partitions can be armed AWAY at the same time from either partition s keypad Both partitions must be Ready To Arm 1 Enter Master Code AWAY AWAY 2 Two beeps will sound as both partitions arm with exit delay 80 Panic Keys Relay Powerline Carrier Devices if used FA4285 Phone Module if used Exit Error Alarm Displays if programmed If the local partition at which the arming is attempted is not Ready To Arm one beep will sound after AWAY is pressed and neither partition will arm If the remote other partition is not Ready To Arm two beeps will sound after the first press of AWAY and a single beep will sound after the second AWAY is pressed and neither partition will arm THIS PROCEDURE IS NOT APPLICABLE TO DISARMI
19. 0 Press the key to continue If a zone list will be used to START the relay action enter the zone list number to be programmed in field 81 1 2 or 3 If not used enter 0 Press the key to continue If a zone type or system operation will be used to START the device action enter the appropriate two digit code see table that follows If not enter 00 Press the key to continue CHOICES FOR ZONE TYPES 00 Not Used 04 Interior Follower 08 24 Hr Aux 01 Entry Exit 1 05 Trouble Day Alarm Night 09 Fire 02 Entry Exit 2 06 24 Hr Silent 10 Interior w Delay 03 Perimeter 07 24 Hr Audible 24 Silent Burglary CHOICES FOR SYSTEM OPERATION 20 Arming Stay 36 At Bell Timeout 42 System Battery Low 21 Arming Away 38 Chime 43 Communication Failure 22 Disarming Code OFF 39 Any Fire Alarm 52 Kissoff 31 End of Exit Time 40 Bypassing 58 Duress 32 Start of Entry Time 41 AC Power Failure 33 Any Burglary Alarm 63 Enter if applicable the partition number 1 or 2 or 0 for any Press the key to continue If a zone list will be used to STOP or restore the device action enter the zone list number 1 2 or 3 to be programmed in 81 mode If not used enter 0 Press the key to continue If a zone type or system operation will be used to STOP the device action enter the appropriate two digit code see the ZT choices listed above If not enter 0
20. 2 digit phone code e Ifthe premises phone system includes an answering machine the 2 digit phone code should be entered during a pause at the beginning of or during the outgoing answering machine message When the 2 digit phone code is entered the caller will hear a voice prompt asking for entry of the 4 digit system code ENTER SYSTEM CODE NOW The caller should then enter the installer code 4112 As a safety feature there is a 3 try limit in which to enter each code phone code and system code after which time the call in will be aborted Also if no keys are pressed for a period of 20 seconds the call in will be aborted Annunciation of a system status report will start if both codes were entered correctly During any pause in the status report or immediately following it the caller should key the following via the keypad on the phone Installer Code 4112 then 1 OFF A beep should be heard and from a wired keypad on the premises and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard on the caller s phone indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone At this point the caller can hang up the phone Verify with the caller that there was successful access to the system and that the appropriate annunciations were heard over the phone If the Phone Module functioned satisfactorily unplug the AC transfo
21. 200ft 60m nominal indoors from wireless transmitters the actual range to be determined with system in TEST mode With the Ademco FA162C 5881L 5882L accepts up to 8 transmitters 5881M 5882M accepts up to 16 transmitters 5881H 5882H accepts up to 24 transmitters 2 1 4 W x 4 1 8 H x 7 8 D 57mm x 105mm x 22mm Voltage Input 12VDC Current Drain 20mA Physical Zones Physical Electrical Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 35mA 8 EOLR Loops A H Loop A can be set for fast 10 15msec response to an open Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 15mA Relays off 180mA Relays on Four Output Relays SPDT Contacts Rating 2A max at 28VDC AC Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 35mA Relays off 100mA Relays on 8 EOLR Loops A H Loop A can be set for fast 10 15msec response to an open Two Output Relays SPDT Contacts Rating 2A max at 28VDC AC Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm Electrical Voltage Input 12VDC Current Drain 160mA Device Address Permanently set to address 4 Telephone Line Connections See FA4285 PHONE MODULE section 90 Accessories Compatible Devices Sounders Compatible 2 Wire Smoke Detecto
22. 2451 2451TH 1400 1451 2451 1451DH System Sensor 1412 2412 2412TH A77 716B 2112 24T Photoelectric w heat sensor direct wire Photoelectric direct wire Photoelectric w heat sensor direct wire Photoelectric w B401B base Photoelectric w heat sensor amp B401Bbase Ionization direct wire Ionization w B401B base Photoelectric duct detector w DH400 base Ionization duct detect w DH400 base 4 wire ionization products of combustion detector 4 wire photoelectric smoke detector 4 wire photoelectric smoke detector w 135 F 57 C heat detector EOL relay module supervisory module for wired 4 wire fire zone Low profile 4 wire photoelectric smoke detector w 135 F 57 C heat detector 91 APPENDIX A 5800 RF System Wireless Transmitters Transmitter Input Loop Identification 5800 Series Transmitter Input Loop Identification e All of the transmitters illustrated below have one or more unique factory assigned input loop ID codes Each of the input loops requires its own programming zone e g a 5803 s three inputs require three programming zones e Transmitter inputs entered as RE Supervised RF Type send periodic check in signals as well as fault restore and low battery signals The transmitter must remain within the receiver s range UR Unsupervised RF Type send all the signals that the RF Type does but the control does not supervise the check in signals The transmitter may t
23. 50 49 50 51 SPLIT DUAL REPORTING 0 Use options 0 5 when reporting to standard telephone receivers TO PRIMARY TO SECONDARY 0 All reports none unless primary fails then all Alarms Restore Cancel Use options 6 9 when reporting to a pager is desired TO PRIMARY TO PAGING No 16 All reports except Open Close Alarms Open Close Troubles All reports Alarms Troubles 8 All reports Alarms Open Close Troubles All reports except Open Close Alarms Open Close for users 5 25 Troubles Can only be used is primary reporting format is Ademco Contact ID See explanation of pager report format below wil report users 5 16 and if using wireless button type devices will report the zone number of the arm or disarm button 10 25 Open Close for users 1 4 are not reported Pager Report Format Options 6 9 send reports to the primary phone number and send reports to a pager which has its phone number entered as the secondary phone number in field 42 The pager report is a 10 digit code in the following format SSSS EEE NNN where SSSS 4 digit subscriber number field 43 first digit cannot be 0 EEE 3 digit event code as follows 911 alarm NNN zone number 001 Open system disarmed NNN user no 002 Close system armed NNN user no 811 Trouble NNN zone no NNN 3 digit user number or zone number as described in EEE Refer to the User Ma
24. 8 0 0 on an alpha keypad Enter Serial Number Sequential mode by pressing 83 The following prompt will be displayed NOTE See the ZONE PROGRAMMING section for an explanation of the programming tool If using a program tool enter 1 If not using a tool enter 0 Ifa 9 3 gt PROGRAM TOOL tool has already been programmed this prompt will not appear If 0 NO 1 YES 0 either not using a tool or one has already been programmed skip to step 4 N 3 If 1 is entered the system will prompt for the unit s serial number 00 INPUT S N L Enter the program tool s serial number using one of the following AXXX XXXX methods a Enter the 7 digit serial number printed on the transmitter or b Press any button on the transmitter The keypad should beep twice and display the serial number of the tool 00 INPUT S N L In this example the serial number is A123 4567 Once enrolled you can use the program tool to ready the system for enrolling a A123 4567 3 transmitter s serial number by first pressing the upper left hand button of the program tool then activating the desired transmitter see procedure at the LEARN S N prompt The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool Press to continue Press the key on the keypad to back up to the PROGRAM TOOL prompt 4 Enter the first zone number to be enrolled e g zo
25. Low Speed Standard or Expanded Sescoa Radionics Standard or Expanded Ademco Express Ademco Contact ID You can assign Alpha descriptors to all zones useful only when using Alpha keypads and or the FA4285 Phone Module AC Power Supply Uses 1321 110VAC plug in transformer with 16 5VAC 25VA output unless Powerline Carrier devices ex X 10 type are used in which case a 4300 transformer module must be used Back Up Battery Rechargeable Gel type 12VDC 4AH minimum 9 Section 2 INSTALLING THE CONTROL This section provides instructions for mounting the control cabinet and installing the cabinet lock if used Also included in this section are instructions for the following e Installing the main PC board e Mounting the 5881 5882 in Canada RF Receiver board in the cabinet if used e Standard phone line connections e Installing the back up battery in the cabinet e Connecting the AC transformer e Making earth ground connections Mounting the Cabinet Mount the control cabinet to a sturdy wall using fasteners or anchors not supplied in a clean dry area which is not readily accessible to the general public Four mounting holes are provided at the back of the cabinet If an RF Receiver is being used and you intend to mount its PC board within the cabinet note the following e Do not mount the cabinet on or near metal objects This will decrease RF range and or block RF transmissions from wireless transmitt
26. Report Code 1st Digit 54 DE BU RE N 8 29 39 44 63 81 90 alarm sotinders eso See ERC ces 37 ADO WEE 7 21 22 29 90 Alpha descriptor ecooooccnnoccnononononnnononcnconnnnnononcnoncnnannnaninnss 68 AS getest 7 8 21 22 29 39 44 63 81 90 Alpha keypad esc EE EE GEE rindan coin donado geed 7 44 FA4285 ces 12 32 33 34 35 39 69 90 Alpha Vocabulary smece en a AR EA 66 FA4285 Phone Module sesse see Re RA 8 66 Alpha Vocabulary List sesse ese RA RA Re 67 4300 transformer conooooccncccnonnonnnnnconnnnnnnncnonannns 8 12 29 30 answering machine cooooccnoncccnoonncnonnnnnoncnnnononcnononcnoncnnono 56 AS TED EE 15 Arm Away Stay Report Code B A 3 A WE EO EE OE ee os 5 Armins de AO OE EE HE e Ta tes 80 DISTAD oia 7 9 14 15 43 89 Arming Instant cintia ag Se ds eke 80 EA YE NE Soest EE N NE EDE 15 Arming Maximum 80 5800 series transmitters esse esse ee Re 25 28 Arming Mode EE EE RE Gee ED EG dee 80 UNN E 25 90 Arming Stay ti EER RR EN end 80 DREI SR RE EE ER EE 25 26 71 ATMA Ve Vee ER GR Ese ves geed Se Se EE Ee EE ede 46 VER AE NE ME N EE EL 25 96 82 EE 46 O RE 25 26 82 ATLIS BE Sinai dada Ba sege Se ee 87 D802MN GR EE OR EE hd 25 Audible Exit Warning oooooocccnnoncnnnonnnnnonnnnnnoncnnnnnnncnonoss 49 dis ME EE EL EE EE 25 26 27 82 Audio Alarm Verification omooooccncnnnonnnnnnnnnonnnnncnnnno 8 39 ataO oE a ada 27 Audio Alarm Verification AAV sesse sesse ee Re ee 32 l
27. See box This is sent when a transmitter that previously sent in a low battery message has sent a message indicating it no longer has a low battery condition TEST RESTORE REPORT CODE 010 This is sent when the test mode is exited See box Reports with Partition 1 Subscriber No A restore code entered here will cause a restore message to be sent when Test mode is exited EVENT LOG 80 FULL REPORT CODE 010 If an Event Logging selection is made in field 90 a message can be sent to the central station receiver when the log is 80 full If the log becomes full a new message will overwrite the oldest message in the log Note Aside from the selection made by the installer in field 90 all control and readout from the log is accomplished via the Downloader EVENT LOGGING 3 0 No event logging 1 log Alarm Alarm Restore 2 log Trouble Trouble Restore 4 log Bypass Bypass Restore 8 log Open Close x log combination of events add value of entries Example To select Alarm Alarm Restore and Open Close enter 9 1 8 to select all events enter 15 Press first to enter 2 digit options The default of 3 alarm alarm restore 1 plus trouble trouble restore 2 54 DOWNLOAD INFORMATION 94 95 91 92 EVENT LOGGING continued The FA162C system has the ability to record various events in a history log 48 event
28. UP UPR HOUSE ID SWITCH DOWN FOR OFF UP UP UP SHOWN SET FOR HOUSE ID 30 UP UP UP Se UP UP UP UP URI Up UP UP AE UP UP UP UP UP UP UP UP UP Section 7 RELAY OUTPUTS 8 POWERLINE CARRIER DEVICES Relay Powerline Carrier Device Basics Relays and Powerline Carrier devices ex X 10 brand devices are programmable switches that can be used to perform many different functions They can be used to turn lights on and off control sounders or for status indications In this system each device must be programmed as to how to act ACTION when to activate START and when to deactivate STOP Each of these is described and in the programming procedure for 80 and 81 interactive modes that are provided in the programming sections of this manual The control supports a total of 8 output devices in the following configurations e One 4204 relay module 4 relays and 4 Powerline Carrier devices e One 4229 zone relay module 2 relays and 6 Powerline Carrier devices e Up to 8 Powerline Carrier devices 8 minus the number of output relays used Fa A 4204 cannot be used if a 4219 or 4229 is already being used and vice versa The 4204 and 4229 modules provide Form C normally open and normally closed contacts Powerline Carrier devices a
29. Zone Descriptors NOTE The list below is a revised vocabulary list which differs from earlier versions of the FA160C Use only this list when programming FA162C zone descriptors 000 001 002 004 005 006 007 009 010 012 013 014 016 017 018 019 020 021 022 023 025 026 028 029 030 031 033 034 035 036 037 038 040 046 047 048 049 050 051 052 053 054 055 057 059 060 061 062 Word Space A AIR ALARM ALLEY AMBUSH AREA APARTMENT ATTIC AUDIO B BABY BACK BAR BASEMENT BATHROOM BED BEDROOM BELL BLOWER BOILER BOTTOM BREAK BUILDING Cc CABINET CALL CAMERA CAR CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLOSED COMPUTER CONTACT D DAUGHTERS DELAYED DEN DESK DETECTOR DINING DISCRIMINATOR DISPLAY DOOR DOWN DOWNSTAIRS DRAWER DRIVEWAY 064 065 066 067 068 069 071 072 073 075 076 077 079 080 081 082 083 084 085 089 090 091 092 093 094 095 096 098 099 100 101 102 103 104 105 106 107 108 109 110 111 113 DUCT 114 LOADING 168 SHED 226 0 115 LOCK 169 SHOCK 227 1 EAST 116 LOOP 170 SHOP 228 1ST LECTRIC 117 LOW 171 SHORT 229 2 eMengecy MB LOWER 173 SEO AD ENTRY M EQUIPMENT 119 MACHINE 175 SLIDING se SAD 176 SMOKE 233 4 EXIT 121 MAIDS 178 SONS 234 4TH EXTERIOR 122 MAIN 179 SOUTH 335 5 F Ee MASTER 180 SP
30. and all continuous keypad sounds in all partitions will be shut off A You must connect a 4204 or 4229 relay module when using an AAV unit Do not use relay output number 1 for any other usage Wiring Connections The method used to trigger AAV is via the use of a 4204 or 4229 relay module as shown in the AAV connection diagrams that follow one diagram for connections when a FA4285 Phone Module is used the other when the FA4285 is not used 39 INCOMING TELCO LINE 9 EA DIRECT Elo CONNEC CORD p pex Ue gig PREMISES ANSWERING MACHINE AND PHONES TERMINALS ANSWERING ON CONTROL gt 21 22 23 24 25 gt Earm MA GROUND ON a T HAHERE AS El z 2 REFER TO HS AAV MODULE die INSTRUCTIONS ds FOR CONNECTIONS 2 TO AUDIO SPEAKERS O AND MICROPHONE sl lie 9 As EAGLE SECURITY x eg MODEL 1241 E S OTP TOTEM 21 MISEN 4204 or 4229 pa y RELAY MODULE NOTE VDC DO NOT USE RELAY 1 FOR GND ANY OTHER PURPOSE RELAY 1 SHOWN OFF NO NC C 112 3 Figure 20 Connection Of AAV Unit When Not Using A FA4285 Phone Module INCOMING TELCO LINE o alz DIRECT El CONNEC CORD y HE 4285 ET GREY RING UU sack RING S PREMISES S ANSWERING MACHINE AND ER PHONES
31. any key Instruct users to call for service immediately upon seeing any of the following messages e A display of CHECK and one or more zone numbers indicates that a problem exists with the displayed zone s and requires attention Note The control will sense a high resistance in the loops on hard wired zones 2 8 and display CHECK and the affected zone number when the system is in the disarmed mode It will not be possible to arm the system as long as this condition exists unless this zone is bypassed If the system is in the armed mode when the high resistance condition occurs this display will not appear but will do so as soon as the system is disarmed Check the sensor or the loop wiring for the displayed zone When the problem has been corrected the display can be cleared by entering the OFF sequence code plus OFF key twice e A display of CHECK and 09 indicates that communication between control and a zone expander or wireless receiver is interrupted Check the wiring and DIP switch settings on the units e If there are wireless sensors in the system the CHECK condition may also be caused by some change in the environment that prevents the receiver from receiving signals from a particular sensor e Adisplay of BAT Fixed word keypads or SYSTEM LO BAT Alpha keypads with no zone number indicates that the system s main standby battery is weak e A display of BAT Fixed word keypads or LO BAT Alpha keypad
32. capacity The types of events to be logged can be selected as indicated At any time the downloader operator can then upload the log and view or print out all or selected categories of the log The log can also be cleared by the downloader operator The display printout at the central station will show the date time event and description of the occurrences The time is calculated by an internal clock at the central station computer Note that the time for any events that occur prior to a system power down or an entry into the programming mode cannot be calculated by the central station computer The time will then appear on the log as unknown NOTE System messages are logged when any non zero selection is made OPTION SELECTION Audio Alarm Verification 8 0 not using AAV 1 local lockout 2 sounder delay 3 local lockout and sounder delay 4 an Audio Alarm Verification AAV unit is connected to the system 5 local lockout and AAV 6 sounder delay and AAV 7 local lockout and sounder delay and AAV 8 exit delay restart For combinations of exit delay restart option 8 with options 1 7 enter the sum of the options desired Ex To select AAV and exit delay restart enter 12 4 8 Press first to enter 2 digit options UL installations must be 0 AAV disabled PHONE LINE MONITOR ENABLE 0 0 Not used 1 Local keypad display only when phone line is faulted 2 Local keypad display plus keypad troubl
33. enter the Installer code 4 1 1 2 8 0 0 This method is disabled if you exit the program mode using 98 instead of 99 See Exiting Program Mode paragraph later in this section If a different Installer code is subsequently programmed use it instead of 4112 to gain access to the Programming mode Following entry into program mode data field 20 will be displayed this is the first data field in the system The system will now accept entries for field 20 Programming a Data Field 1 Press plus Field No for example 21 then make the required entry 2 When you have completely programmed a data field the keypad will beep three times and then automatically display the next data field in sequence To go to a different field press plus the desired field No 3 If the number of digits that you need to enter in a data field is less than the maximum digits available for example the phone number field enter the desired data then press and the next data field number to be programmed 4 If you try to enter a non existent field the keypad will display EE or Entry Error Simply re enter plus a valid field number 43 Reviewing a Data Field Erasing an Entry in a Data Field Press 4 plus Field No Data will be displayed for that field number No changes will be accepted in this mode To delete an entry in a field press plus Field No Applies only to fields 40 46 and 94 Interacti
34. etc connected to a single 4 wire run determine the current drawn by all units connected to the single wire run then refer to the Wiring Run chart to determine the maximum wire length that can be safely used for each wire size Current draw for all devices can be found in the SPECIFICATIONS AND ACCESSORIES section Note Refer to Auxiliary Device Current Draw Worksheet in the FINAL POWER UP section for current draw for all keypads also be determined from the chart based on the current draw of that device alone Wiring Run Chart For Devices Drawing Aux Power From The Control 12V amp 12V Et TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN 50 mA or less 100 mA 300 mA 500 mA 600 mA A Maximum wire lengths for any device that is homerun to the control can Includes Keypads RF Receivers Zone Expander Relay Units or FA4285 Phone Module 1500 feet 457m when unshielded quad conductor cable is used 750 feet if shielded cable is used This restriction is due to the capacitive effect on the data lines when quad cable is used A The length of all wire runs for both partitions combined must not exceed 2 Run field wiring from the control to the keypads using standard 4 conductor twisted wire cable using the wire gauge determined in step 1 14 3 Connect remote Keypads for Partition 1 to terminals 4 5 6 and 7 on the control board as shown in Figure 6 4 Connect
35. examples of good earth grounds available at most installations Metal Cold Water Pipe Use a non corrosive metal strap copper is recommended firmly secured to the pipe to which the ground lead is electrically connected and secured AC Power Outlet Ground Available from 3 prong 120VAC power outlets only To test the integrity of the ground terminal use a three wire circuit tester with neon lamp indicators such as the UL Listed Ideal Model 61 035 or equivalent available at most electrical supply stores BER Section 3 INSTALLING REMOTE KEYPADS This section lists the wired keypads that may be used and provides instructions for wiring and mounting the keypads A preliminary check out procedure is also provided to ensure that the connected keypads are functioning properly in the system Keypads That May Be Used e Fixed Word Display FA210KP FA250KP e Alpha Display FA550KP FA450KP e Up to 4 keypads in each partition total of 8 in the system independent of auxiliary power considerations you may need to use an auxiliary power supply if the 600mA aux output is exceeded Z Make sure that keypads are set to the non addressable mode address 31 Wiring To The Keypads 1 Determine wire gauge by referring to the wiring length gauge chart below Wire lengths gauge for Partition 2 keypads should be determined separately from those keypads connected to Partition 1 For devices Keypads RF Receivers Zone Expander
36. following chart defines the three sets of handshake kissoff frequencies that the panel supports and the different formats that can be sent for each FORMAT HANDSHAKE TRANSMITS DATA KISSOFF TRANSMIT TIME Low Speed 1400Hz 1900Hz 10PPS 1400Hz Under 15 secs 3 1 Standard report 4 1 4 2 Sescoa Rad 2300Hz 1900Hz 20PPS 2300Hz Under 10 secs 3 1 Standard report 4 1 4 2 Express 1400 2300Hz DTMF 10 cps 1400Hz Under 3 secs 442 Contact ID 1400 2300Hz DTMF 10 cps 1400Hz Under 3 secs 76 The following describes each format in greater detail 3 1 and 4 1 Standard Formats Comprise a 3 or 4 digit subscriber number and a single digit report code e g Alarm Trouble Restore Open Close etc 3 1 and 4 1 Expanded Formats Comprise a 3 or 4 digit subscriber number and a two digit report code The first digit is displayed on the first line followed by a second line where the first digit is repeated 3 or 4 times and followed by the second digit This is the expanded digit 4 2 Format Comprises a 4 digit subscriber number and 2 digit report code Ademco Contact ID Comprises a 4 digit subscriber number 1 digit event qualifier Reporting Format new or restore 3 digit event code 2 digit Partition No and 3 digit zone number user number or system status number see the following page 3 1 4 1 3 1 4 1 Report Standard Expanded 4 2 Alarm SSS S
37. in a Data Field cooonnnnnnnos 44 Interactive Mode Programming 56 80 82 and en 44 Loading Factory Defaults nena Gee Ee AA Se AA Ge AAR ee Ge ee ee arc cnn anna ee RA ei ce 44 Programming System Setup Fields ccoooooccnonocnncnonono oe RA Se RA Se RA Ge AA ee Se AA ee AA Exiting the Programming Mode iss ss se sees ese ee Ge ee ER AEPA N ee Ge Re ee ee ee ee ee ee 44 ZONE RESPONSE TYPE DEFINITIONS oooonccconononoonccoonncconconnonononnncnnnnonnnnccnnnnonnn ses 45 DATA FIELD DESCRIPTIONS AAA 47 ZONE PROGRAMMING 56 Menu Mode 57 OUTPUT DEVICE PROGRAMMING 80 Menu Mode iese esse esse ee see ee se 61 ZONE LISTS 81 Menu Mode ege EENS EES kke sk Se Es cani ares ee Ee eg 65 ALPHA DESCRIPTION PROGRAMMING 82 Menu Mode ees sesse sees 66 Assigning Zone Descriptor s d sess SEE dia 66 Entering Zone Descriptors in program Menu Mode eg 66 GETAG Ere GESE EE OE EE EO N 69 Alpha Vocabulary List For Entering Zone Descriptors sesse sees esse ee see ee Se ee 70 Character ASCID Chart ii Ee Meet de ER GE Ee ee Ee be Ee EE 70 USING SEQUENTIAL MODE 83 Menu Mode iese sesse esse ee esse ee ee ee ee ee ee ee 71 REMOTE PROGRAMMING AND CONTROL DOWNLOADING ees 74 General Dk eie val ie tee RO EE ee EE OR R IEREN 74 Eduipment Rd as 74 Tnititial Download EE 74 Remote Programming Information onononnnnnnnnnnnnnnnnnnnnnnnnn Re ee ee ee 75 Remote Programming Advisory Notes iis sesse s
38. monitoring station in the event that the telephone lines are out of order alarm signals are normally sent over the phone lines if connected to an alarm monitoring station 2 TABLE OF CONTENTS Section 1 GENERAL DESCRIPTION AAA 7 Section 2 INSTALLING THE CONTROL AAA 10 Mounting the Cabinet aogier Ea rE EE ELEA AEA e a GEE EER ee ee lid 10 Installing the Lock if iised EE eects sien See D ET REAT 10 Mounting the Control s Circuit Board Alone in the Cabinet 11 Mounting Control and RF Receiver Circuit Boards Together in the Cabinet 11 Standard Phone Line Connections eise sesse see ee Gade Ee Re AA de AA EA GRA ed ee ee ee 12 Wiring the AC Transformier A ca 12 Installing the Back Up Batter 13 Earth Ground Connections iis ee ses de Gee de RA AA ee AR AA AA Ge ee nn cana nc ee AA ee ge 13 Section 3 INSTALLINGREMOIERKEYDAIDS AA 14 Keypads That May Be Used co ee ee ee ee ee ee ee 14 Wiring The ea GER EE EE EE EE N OE Rd 14 Mounting The RKeepade iese ees ee se ainei nisip EN E GR Re Ge ee AR ee AR Re ARA 15 Using A Supplementary Power Supply To Power Additional Keypads sesse esse 15 Preliminary Check Out Procedure sees se ee se ee RA Se RA Ge RA ee AA ee ee ee 16 Section 4 BASIC HARD WIRED ZONES LS 17 Installing the Hard Wired Zones esse ee esse se ee se ee ee se ee ee ee ee ee Ee ee Ge ee ee ee ee ee 17 Common Characteristics For Zones 18 17 Wiring Burglary and Panic Devices
39. of the inputs requires its own programming zone e g a 5803 s three inputs require three programming zones See APPENDIX A toward the end of this manual Transmitters can be enrolled as one of the following types RE Sends periodic check in signals as well as fault Supervised RF restore and low battery signals The transmitter must remain within the receiver s range UR Sends all the signals that the RF Type does but the Unsupervised RF control does not supervise the check in signals The transmitter may therefore be carried off premises BR These only send fault signals They do not send low Unsupervised Button battery signals until they are activated The RF transmitter may be carried off premises Transmitter Battery Life be indicated in the procedure that follows under Programming the Receiver Z Do not install batteries in wireless transmitters until ready to enroll as will and Transmitters After enrolling batteries need not be removed e Batteries in the wireless transmitters may last from 4 7 years depending on the environment usage and the specific wireless device being used Factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation The wireless system can identify a true low battery situation thus allowing the dealer or user of the system time to arrange a change of battery and maintai
40. powered If Transmitter is 5827 5827BD house code not set in field 24 or transmitter not set to same house code set in that field Transmitter located too for from RF receiver Metal shielding between transmitter and RF receiver Transmitter malfunctioning 5881 5882 malfunctioning Transmitter No zone not programmed 5881 5882 address incorrect Field 22 not set properly Transmitter zone type ZT is set to 00 Not Used Transmitter battery not installed 5800 System transmitter not enrolled in system Bat or System Lo Bat no zone Nos Bat or Kypd LB 00 Bat or Lo Bat nn System is in TEST mode A transmitter low battery has occurred and is displayed A supervision CHECK has occurred Put control in TEST mode If zone does not respond try operating the tamper switch or another input to the transmitter 5a Ifanother input causes the zone to be displayed the wrong input was enrolled when programming 5b If no response at all from this transmitter this physical transmitter has not been enrolled by the system Transmitter Sniffer display is being cleared by another unit programmed for this zone Sensors not properly installed wired or monitored Universal transmitter 5817 programmed wrong Protected door or window opened while system armed Improper user operation of exit entry delays Magnets located too far from switches and or doors and wi
41. restore EEE Event code 3 hexadecimal digits Note For a complete list of event codes refer to the central office receiver manual GG Partition Number system messages show 00 ZZZ Zone contact ID number reporting the alarm or user number for open close reports System status messages AC Loss Walk Test etc contain zeroes in the ZZZ location TABLE OF CONTACT ID EVENT CODES Code 110 374 01 EE 35 2 46 570 Low System Battery Battery Test Fail E Test 05 System Reset AAV to foll Trouble or Tamper Expansion Module Svs To 51 Telco Line Fault Y 623 Event Log 80 Full Long Range Radio Trouble yent og 2o u 629 1 1 3 Day No Event 373 Fire Loop Trouble 1 Disarmed Armed STAY INSTANT Quick Arm Alarm 24 Hour Auxiliary ESE STAY INSTANT 301 78 Section 23 SYSTEM OPERATION Security Codes Installer Code Master Code 2 Partition Arming The system can be set up such that both partitions can be armed at the same time from either partition s keypad To do this simply assign the same master code to both partitions Refer to the Special AWAY Arming paragraph later in this section for arming procedure The installer programs the 4 digit Installer Code initially as part of the programming procedure The factory default Installer code is 4 1 1 2 but may be changed in field 20 The Installer code is the only code that can enter programming mode and also in norma
42. than these are selected for Alpha descriptors the phone module will not provide annunciation of those words 34 wo N t gt Go 30 A A o 32 space OONOUKONAO CHARACTER ASCID CHART For Adding Custom Words 60 lt 74 J 88 xX 61 75 K 89 Y 62 gt 76 L 90 Z 63 77 M 64 78 N 65 A 79 O 66 B 80 P 67 C 81 Q 68 D 82 R 69 E 83 S 70 F 84 T 71 G 85 U 72 H 86 V 73 1 87 W 70 Section 20 USING 83 SEQUENTIAL MODE Use 83 Sequential mode when a wireless transmitter is to be physically added removed or simply changed as when replacing a unit that has a non removable battery By using this mode you can add delete or change the serial number of a transmitter in a zone but retain all other existing data that has been programmed for that zone Certain button type transmitters have more than one button e g 5801 Note that each button must be assigned to a different zone Similarly the 5816 transmitter has contact terminals and a reed switch for use with a magnet If using both each must also be assigned to a different zone This means that the procedures that follow must be repeated for each button or contact on the transmitter NOTE Use this mode only after all other zone information has been programmed including transmitter loop numbers To enroll transmitters sequentially after all other zone information has been programmed do the following 1 Enter Programming mode Installer Codel
43. the programmed alarm code for that zone If 3 1 or 4 1 format is used only the digit entered in this field will be sent This message will go to the Primary Phone No Under any of these conditions no Restore message will be sent If 0 is entered in this field no special message will be sent only the regular alarm and alarm restore code for the zone TROUBLE REPORT CODE See box above 010 This will be sent if a zone goes into trouble BYPASS REPORT CODE See box above 010 This will be sent when a zone is manually bypassed AC LOSS REPORT CODE 010 See box on previous page Reports with Partition 1 Subscriber No Timing of this report is random with up to a 4 hour delay If AC restores before the report goes out there is no AC restore report LOW BAT REPORT CODE 010 This will be sent when a low battery condition exists in the system s standby battery See box Reports with Partition 1 Subscriber No TEST REPORT CODE 010 This is sent periodically to test that the communicator and phone lines are operational frequency of report is selected in field 51 See box Reports with Partition 1 Subscriber No OPEN REPORT CODE 0 This is sent upon disarming of the system See box 2nd digit user number if expanded or 4 2 reporting is selected ARM AWAY STAY REPORT CODE 0 10 This option allows for independent programming of AWAY and STAY reports for each partition 2nd digit of report is user num
44. the wires connected to terminals 21 amp 22 on the control The wiring diagram shows the wiring connections that will provide proper operation in most cases Caller ID Units If the telephone system on the premises includes a Caller ID unit connect the unit directly to the Handset terminals 21 amp 22 on the control as shown in FA4285 Phone Module Wiring Connections diagram that follows 33 FA4285 WIRING NOTES Wire the FA4285 Phone Module exactly as shown using a direct connect cord and RJ31X jack 2 If Touch tones are not heard when pressing keys following phone access to the security system via an on premises phone try reversing the pair of wires connected to terminals 3 amp 4 on the FA4285 and the pair of wires connected to terminals 21 amp 22 on the control If an error signal fast busy signal is heard when trying to access the system via the phone check for correct line seizure wiring as described in note 4 Connection to the incoming Telco line via a RJ31X jack and direct connect cord as shown in this diagram is essential even if the system is not connected to a central station The FA4285 will not function if this is not done The house phone lines gray and brown wires must be wired to the Phone Module terminals not to the control terminals Otherwise an error signal fast busy signal will occur when trying to access the system from an on premises phone If the telephon
45. to Zones 18 17 Wiring 2 Wire Smoke Detectors to Zone 1 17 Verify Operation of 2 Wire Smoke Detectors in Zone 1 17 Turning Off Fire Alarm Sounding ccccooccncnonocnnnonnnnnnn see ee EE RA ee Re ee ee ee ee 18 Wiring 4 Wire Smoke Combustion Detectors on Zones 23 18 Wiring 2 Wire Latching Type Glass Break Detectors on Zone 8 19 Check Out Procedure for Hard Wired Zones esse ss sees ses es se ee see de se Ad ee ee ee ee ee ed nos 20 Section 5 WIRED ZONE EXPANSION 4219 4229 ee esse ee se ee see ese ee see ese ee ee ee ee se ee se ee ea ens 21 Installing Zone Expansion Units iese ees se ee RR iria ER Re AA GR EEE ee AR ee AR aie 21 Connections and Set Upiiid Ee SE ke e DS A o 21 Check Out Procedure for Wired Expansion Zones 22 Section 6 WIRELESS ZONE EXPANSION 5800 SYSTEM ee esse esse ee ee ees se ee se ee se ee ee ee ee 23 General Information estrictas Ee kk ne Ds Ges SG GEK ER Se dee ENEE eg esse 23 Receiver Supervision Ses sedes si ees ske EES ee ED ee LA SN ee DM Ab AG GE ee Ne se ee vs eseese 23 House Identification Ze EE EE devon abn tote cane ee ee E ee ee E ee Ge ee Ode 23 Installing the 5881 5882 RF Receiver sesse ees se ee Ge RA AR AA AR AA AR RA Ge ee ee ee 23 RF System Installation Advisories cooooocnonoccncnooonnnnnnn ee RA ee RA ee ee AE RA Ge ee ee ee ee 23 Installation and Set Up of the 5881 5882 Receiver cccooococcnoonccncnoonnnno connnnnnnnnnnnncnnnnos 24 Installin
46. to the central station during the following tests 3 and 4 Notify them in advance that tests will be in progress 3 Arm the system and fault one or more zones After 15 seconds if optional dialer delay is selected silence alarm sounder s by entering the code and pressing OFF Check Entry Exit delay zones 4 Check the keypad initiated alarms that are in the system by pressing the Panic key key pairs on some keypads If the system has been programmed for audible emergency the keypad will emit a steady alarm sound and ALARM and zone number will be displayed Silence the alarm by entering the security code and pressing OFF If the system has been programmed for silent emergency there will be no audible alarms or displays but a report will be sent to the central station 5 If output Relay Units Powerline Carrier Devices have been installed test their programmed action 6 Notify the central station when all tests are finished and verify results with them 7 To test the wireless part of the system and the RF Receiver perform the two additional tests that follow a TRANSMITTER SNIFFER MODE Make sure both partitions are disarmed before trying to enter this mode Press Installer code 3 on partition 1 s keypad This initiates a procedure that will check that all transmitters have been properly programmed Note If the communicator is in the process of sending a report to the central station the system will not go into th
47. unit being used as follows 0 none 1 4219 2 4229 3 4204 Default is 0 Exiting the Programming Mode 99 allows re entry into the program mode using Installer Code 8 0 0 98 inhibits re entry into the programming mode using the Installer code If Local Lockout is enabled in field 91 then re entry to program mode must be made by using Installer Code 8 0 0 44 Section 14 ZONE RESPONSE TYPE DEFINITIONS General Information You must assign a zone type to each zone which defines the way in which the system responds to faults in that zone Zone types are defined below Type 00 Program a zone with this zone type if the zone is not used Zone Not Used Type 01 This zone type provides exit and entry delays whenever the zone is faulted if Entry Exit Burglary 1 the control is armed in the Away or Stay modes When the panel is armed in the Instant or Maximum modes no entry delay is provided Entry delay 1 is programmable from 0 99 seconds for each partition Exit delay begins whenever the control is armed regardless of the arming mode selected and is independently programmable form 0 99 seconds field 34 This zone type is usually assigned to sensors or contacts on doors through which primary entry and exit will take place Type 02 This zone type provides a secondary entry delay whenever the zone is faulted Entry Exit Burglary 2 if the panel is armed in the Away and Stay modes When the panel is
48. 0 Press the key to continue Enter if applicable the partition number 1 or 2 or 0 for any Press the key to continue This screen again displays a summary of the current device START programming Press the key to continue This screen again displays a summary of the current device STOP programming Press the key to continue Enter 1 if using a Powerline Carrier Device X 10 if not enter 0 The display then returns again to the first screen so that the next device number to be programmed can be entered or enter 0 0 to end device programming Example of A lamp is to be turned on via a Powerline Carrier device X 10 when any one Output Device of 3 specific zones are faulted or when any 24 hour auxiliary zone is faulted Programming We want to be able to turn off the lamp manually without affecting the arming status of the system To program this we would do the following e In 80 interactive mode we choose Output Device 01 and program the Action A to be 2 Close and stay closed The Event we are looking for to start the Device action is a fault so we will program 2 in EV We will use Zone List 1 for the 3 specific zones so we will program 1 in ZL and we will program these 3 zones in 81 s Zone List 1 e The second condition for turning on the indicator is triggering a 24 hour aux zone Zone Type 08 so we will program ZT as 08 e Next enter the Partition number P in which you wa
49. 0 OUTPUT DEVICES Interactive menu mode applicable only if field 25 is programmed for a 4229 4204 or if Powerline Carrier devices are being used Refer to the OUTPUT DEVICES section for detailed procedure 81 ZONE LISTS FOR OUTPUT DEVICES Interactive menu mode applicable only if 25 is programmed for a 4229 4204 or if Powerline Carrier devices are being used Refer to the ZONE LIST section for detailed procedure 82 CUSTOM ALPHA EDITING Interactive menu mode used to program zone descriptors Refer to the ALPHA DESCRIPTION PROGRAMMING section for procedure 83 SEQUENTIAL MODE Interactive menu mode used to enroll RF transmitter serial numbers Refer to the SEQUENTIAL MODE section for procedure 96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT No FOR DOWNLOADING Pressing 96 initializes the system for downloading 97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES Pressing 97 automatically loads all defaults and erases any information previously programmed 98 EXITS PROGRAMMING MODE Prevents re entry by Installer Code 8 0 0 Allows re entry only by Power up then and unless local lockout is enabled in field 91 99 EXITS PROGRAMMING MODE Allows re entry to program mode by Installer Code 8 0 0 or by Power up then and 56 Section 16 ZONE PROGRAMMING 56 Menu Mode While in program mode press 56 to enter Zone Programming Menu Mode Refer to the zone assignment table for 56 on the separate progra
50. 17 Turning Off Fire Alarm You can turn off Fire alarm sounding by pressing the OFF key on any keypad or Sounding other arming disarming device in that partition To clear the memory of alarm and to reset the detector s alarm enter the security code plus OFF again COMPATIBLE 2 WIRE SMOKE DETECTORS Detector Type Model No Detector Type Model No direct wire 2300TB 2451 w DH400 base Photoelectric direct wire 2400 1451DH Photoelectric w heat sensor Pr w DH400 base direct wire 2400TH Low profile Photoelectric Photoelectric 2451 w B401B base w 1350F thermal 2100T Photoelectric w heat sensor 2451TH w B401B base Low profile Ionization type Ionization direct wire 1400 direct wire 1100 i 2 WIRE SMOKE DETECTOR 4103 SINHO 0002 UL NOTE IN UL INSTALLATIONS ONLY ZONE 1 MAY BE USED FOR FIRE Figure 8 2 Wire Smoke Detector Connected to Zone 1 Wiring 4 Wire Smoke Combustion Detectors on Zones 2 7 The system will support as many 4 wire detectors as can be powered from Auxiliary Power on the control on zones 2 7 Refer to the detector s instructions for complete details regarding its proper installation and operation 1 Connect 12 volt power for the detectors from Auxiliary Power terminals 4 and 5 which will interrupt power for fire alarm reset Observe proper polarity when connecting detectors 2 Connect detectors including heat detectors if used across terminals of the zone selected zones 2 7 may be u
51. 4229 module to the control s keypad terminals see diagram below 2 Set the 4219 or 4229 s DIP switch for device address 1 switch 2 OFF and switches 3 4 5 ON Switch 1 determines expansion zone A s response time ON normal response OFF fast response For location of the DIP switch in the unit see the diagram below location of DIP switch for both units is in the same location For additional information see instructions supplied with the 4219 and 4229 RELAY e EITHER OR BOTH CAN BE USED P A RELAY J CH 4 PIN CONSOLE PLUG DIP SWITCH FOR SETTING ADDRESS AND ZONE A RESPONSE RELAY CONNECTOR 10000 TERMINALS ON CONTROL PANEL 2 GRN DATA OUT TAMPER JUMPER POSITION O TO GONTROL P TERM 6 4229 IN CABINET Cl o NOT TAMPERED oh Gi GROUND TERM 4 350305 4229 REMOTE o slee 51 TAMPER PROTECTED TE of Gi 9 1ev S TERM 5 OO o YEL_ DATA IN 99 PG o FROM gt TERM 7 CONTROL REED TERMINATE EACH lt TAMPER PROGRAMMED ZONE RELAY WITH 1000 OHM 1K S dci d END OF LINE RESISTOR y EACH ZONE S MAX LOOP RESISTANCE 300 OHMS E O L ZONES A B Cp E F G H Figure 11 Wiring Connections 4219 amp 4229 4229 shown 91 Programming Wired Expansion Zones Each zone must be programmed into the system using the 56 Zone Programming mode which assigns charact
52. 63 64 65 66 EXIT ERROR REPORT CODE See box on previous page 0 If the system is armed and an Entry Exit or Interior zone is still open after the exit delay time has expired an alarm will sound at the keypad and external sounder keypad also displays Exit Alarm If the system is disarmed before the end of the entry delay that immediately follows the alarm sounding will stop and no message will be sent to the central station The keypad will display CA fixed word keypads or CANCELED ALARM Alpha keypads If the system is not disarmed before the end of the entry delay mentioned above and an Entry Exit or Interior zone is still open an exit alarm message will be sent to the central station if an Exit Error Report code is selected in this field The keypad will display EA fixed word keypads or EXIT ALARM Alpha keypads and the alarm sounding will continue until the system is disarmed or timeout occurs An Exit Alarm condition will also result if a fault occurs in an exit or interior zone within 2 minutes following the end of the exit delay and an exit alarm message will be sent to the central station If Contact ID format has been programmed the message will contain the zone number and error code 374 Trouble Exit Error to define the alarm as an Exit Error rather than E E or Interior If 4 2 format is used the digit entered in this field will be sent followed by the second digit of
53. Connections 34 Programming the FA4285 Phone Module The system must be programmed for use with the FA4285 Phone Module including assigning a phone code and selecting words from the alpha vocabulary Refer to the Programming sections for specific programming details Checking the Operation of the FA4285 Phone Module To Check Phone Module Operation From an On Premises Phone 1 4 Pick up phone and enter the programmed 2 digit phone code Annunciation of a system status report should automatically start See the User s Guide accompanying the Phone Module for detailed information regarding the nature of the status report if necessary During any pause in the status report or immediately following it key the following via the keypad on the phone Installer Code 4112 then press key 1 OFF A been should be heard on the phone and from a wired keypad and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone Hang up the phone To Check Phone Module Operation From an Off Premises Phone 1 Have someone dial the premises phone number using a TouchTone phone e If the phone system does not include an answering machine 2 long tones will be heard in the caller s phone followed by a voice prompt HELLO ENTER PHONE CODE NOW The caller should enter the programmed
54. Display Window When an alarm occurs keypad sounding and external sounding will occur and the zone s in alarm will be displayed on the keypad Pressing any key will silence the keypad sounder for 10 seconds Disarming the system will silence both keypad and external sounders When the system is disarmed any zones that were in an alarm condition during the armed period will be displayed memory of alarm To clear this display simply repeat the disarm sequence enter the security code and press the OFF key again The keypads also feature chime annunciation and 3 panic key pairs or individual panic keys depending on keypad type see Panic Keys below for silent audible fire or personal emergency alarms These keys can notify the central station of an alarm condition if that service is connected The following is a brief list of system commands For detailed information concerning system functions refer to the User s Manual Disarmed Not Ready Before arming the system must be in the READY condition all zones must be intact If the NOT READY message appears press the READY key to display faulted zones Arming Away 000 Enter code AWAY 2 Arming Stay Enter code STAY 3 Arming Instant Enter code INSTANT 7 Arming Maximum Enter code MAXIMUM 4 Disarming esse ees Enter code OFF 1 Bypassing Zones Enter code BYPASS 6
55. F 1 Zone Number 10 Zone Type Perimeter 03 Zone Type 10 Partition 1 10 Report Code 1st 03 2nd 12 00 10 INPUT DEV LP RF TRANS RF 1 Zone Number Zn Enter the zone number that you wish to program or 00 to exit zone programming Press to continue A summary display appears showing the status of that zone s programming If it is programmed satisfactorily press 4 to back up one step and enter another zone number if desired If the zone is not programmed or you want to make changes press to continue Zone Type ZT Each zone must be assigned to a zone type which defines the way in which the system responds to faults in that zone Enter the zone type code or change it if necessary Zone types are listed below 00 Not Used 06 24 Hr Silent 20 Arm Stay 01 Entry Exit 1 07 24 Hr Audible 21 Arm Away 02 Entry Exit 2 08 24 Hr Aux 22 Disarm 03 Perimeter 09 Fire W verif 23 No Alarm 04 Interior Follower 10 Interior w Delay Response 05 Trouble Day Alarm Night 24 Silent Burglary Default values for zones 01 to 08 are Zone No Zn 01 02 03 04 05 06 07 08 Zone Type Default 09 01 03 03 03 08 03 08 Partition Default 1 1 1 1 1 1 1 1 Response Time Default 1 1 1 1 1 1 1 1 1 for response time 350 msec Press to continue Partition No P Default 1 Enter 1 or 2 Press to continue Re
56. FA4285 Phone Module is used If using a FA4285 Phone Module select from those words in the Alpha Vocabulary list shown in boldface type The Phone Module will not provide annunciation of the other words d If a FA4285 Phone Module is added to an existing FA162C system the Alpha descriptors presently in the system should be re programmed selecting from those words shown in boldface type in the Alpha Vocabulary list The Phone Module will not provide annunciation of any other words The ALPHA VOCABULARY LIST and CHARACTER CHART can be found on a following page Zone Descriptors The Alpha Keypad used with the FA162C can have a user friendly English language description location of all protection zones keypad panics and RF receiver supervision faults programmed into the system Each description can be composed of a combination of words up to a maximum of 3 selected from a vocabulary of 196 words stored in memory see a following page In addition up to 10 installer defined words can be added to those already in memory Thus when an alarm or trouble occurs in a zone an appropriate description for that zone s location will be displayed at the keypad Note Alpha Descriptor entry can be done locally at the Alpha Keypad or remotely using Downloading software The Alpha keypad procedure is described below Programming Zone Descriptors program menu mode 82 The descriptor can be entered when the zone is being define
57. FOR PARTITION S daa SEE INSTRUCTIONS 50 OR RELAY VOLTAGE RED SR _GRN__ ADEMCO No 4204 RELAY MODULE 4 WIRE SMOKE 13 8VDC Bee z S KEYPADIS 000000000 AU YEL 4 OUTPUT RELAYS OR COMBUSTION MODULE i Sera DETECTOR 77 71 e Es NE OOO 123456789 oul AND OR orms Es LOAD ON BATTERY ADD 100mA TO HH EE se ADEMCO 5881 Type SU RECEIVERS TO HI SIDE OF SELECTED ZONE Fa TOTAL OF AUX POWER OUTPUT AND A o 000 Si BLK __ RE RECEIVE POR DEVICE Ss 5 a n 0 SEE p S H lt TOTERM6 Ak UB To e INSTRUCTIONS TO LO SIDE OF SELECTED ZONE TOTERM7 e n IF PROGRAMMED FOR FIRE USE UL LISTED ER 2 GIG GE 8 GC 8 Gi io 2 Y Di Dei 7 is y E E E E Gei CABLE FOR ALL CONNECTIONS ITS S Zs 7S ZX 2 di ES E de o TIP RING TIP RING gt 9 TOTS T T BROWN GRAY GREEN RED rd A ee es AUX POWER 5 A 2 P P P P P HANDSET INCOMING OUTPUT E O O SMOKE o o o O O PHONE LINE 10 5 13 8VDC 5 d d d J J TELEPHONE WIRING PLUG IN TRANSFORMER P S00mA MAX T Bl E VIA RJ31X JACK AND DIRECT EARTH 16 5VAC 25VA e g ADEMCO INTERRUPTS o ol 306 O O o O O CONNECT CORD GROUND 4301 Gi FOR FIRE Z al wu SEE INSTRUCTIONS No 1321 TE El Soo SE gt d Gate hd o FOR CONNECTION OF FORIPROBER Q 5 2 OPTIONAL FA4285 VOICE MOD GROUNDING NOTE o al 5 ULE TO PHONE TERMINALS SEE TO 110VAC KEYPAD S 2 Zi pe E INSTRUCTIONS UNSWITCHED CURRENT N MM w ri OUTLET 24HR BOTH gt u alz z 3 WARNING PARTITIONS T N N
58. H 5882H up to 30 Receiver Supervision The receiver is supervised and a trouble report will be generated CHECK and zone 09 will also be displayed a Ifcommunication between the panel and the receiver is interrupted or b If no valid RF signals from at least one supervised wireless transmitter are received within 12 hours House Identification If you are using a 5804BD 5827 or 5827BD Wireless Keypad with the system you must program a House ID Code 01 31 in field 24 to establish proper communication and the keypad must be set to the same ID House ID 00 disables all wireless keypads Installing the 5881 5882 Receiver RF System Installation Advisories Disregard the following advisories if the receiver is mounted in the control cabinet 1 Place the RF Receiver in a high centrally located area for best reception 2 Do not locate the receiver or transmitters on or near metal objects This will decrease range and or block transmissions 3 Do not locate the receiver in an area of high RF interference revealed by frequent or prolonged lighting of the LED in the receiver random flicker is OK 4 The RF receiver must be at least 10 feet from any remote keypads to avoid interference from the microprocessors in those units 23 Installation and Setup of the 5881 5882 Receiver 1 2 Set the receiver s DIP switch for device address 0 as described in its instructions all switches to the right
59. ING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized First Alert WW PROFESSIONAL SECURITY SYSTEMS 172 Michael Drive Syosset New York 11791 Copyright 1997 PITTWAY CORPORATION N7526 1V3 8 97
60. INSTALLATION INSTRUCTIONS FA162C 2 PARTITIONED SECURITY SYSTEM First Alert Ne PROFESSIONAL SECURIT Y SYSTEMS Principal changes between the FA162C and the former FA160C are indicated by margin lines N7526 1V3 8 97 RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations For The Location Of Fire And Burglary Detection Devices Help Provide Proper Coverage For The Protected Premises Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke heat detectors we subscribe to the recommendations contained in the National Fire Protection Association s NFPA Standard 72 noted below Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows For minimum protection a smoke detector should be installed outside of each separate sleeping area and on each additional floor of a multi floor family living unit including basements The installation of smoke detectors in kitchens attics finished or unfinished or in garages is not normally recommended For additional protection the NFPA recommends that you install heat or smoke detectors in the living room dining room bedroom s kitchen hallway s attic furnace room utility and storage rooms basements and attached garages In addition we recommend the following e Install a smoke detector inside every bedroom where a smoker sleeps
61. If some hard wired zones have been assigned to partition 1 and others to partition 2 you will need to observe the keypad in the appropriate partition as each zone in that partition is faulted and restored 5 When you get the proper displays on the keypad s the hard wired zones in the system are functioning properly 6 Unplug the AC transformer 20 Section 5 WIRED ZONE EXPANSION This section provides information regarding the use of expansion modules for expanding the number of wired zones in the system the modules that can be used and their wiring connections Installing Zone Expansion Units You can add an additional 8 wired EOLR zones to the basic control s 8 zones for a total of 16 wired zones by using a No 4219 Wired Expansion Unit or 4229 Wired Expansion Relay Unit Location e You can mount an expansion unit within the control cabinet if space permits Otherwise mount the unit outside the cabinet Supervision e Units are supervised against removal Keypads will display CHECK and zone 09 if a zone expander is disconnected e Units have tamper protection for security when mounted outside of the cabinet Zone Information Assign zone numbers 10 17 for the eight wired expansion loops designated A to H You can program these zones individually in 56 interactive mode for Partition 1 or 2 Expansion zones must also be programmed as input type 2 AW when prompted Connections and Set Up 1 Connect the 4219 or
62. N TO PREVENT RISK OF SHOCK USE 4300 TRANSFORMER t INTERFACE IN AATE S SI DISCONNECT TELEPHONE LINE AT W RIER DEVICES ARE BEING USED SEE DEVICES a 2 2000 2000 2000 2000 2000 2000 2000 TELCO JACK BEFORE SERVICING INSTRUCTIONS FOR CONNECTIONS DRAWING A OHMS OHMS OHMS OHMS OHMS OHMS OHMS THIS UNIT POWERTROM Som EOLR EOLR EOLR EOLR EOLR EOLR MUST BE PARTITION 1 3 MAXIMUM LOOP RESISTANCE EACH ZONE 300 OHMS THIS EQUIPMENT SHOULD BE INSTALLED IN ALARM a FOX CURRENT REMOTE KEYPADS No S8007M Ee 8 10 350 OR 700 MSEC E lil all 10 5 18 8VDC 2A MAX 700mA MAX FOR UL Sea TEN EACH PARTITION CAN deele MODULE 20mA PROGRAMMABLE PROTECTION ASSOCIATIONS STANDARD 74 g A S S j or No USAGE INCLUDING AUX POWER CALCULATIONS EE 30mA Wireless Bi directional Keypad THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES NATIONAL FIRE PROTECTION ASSOC STEADY FOR BURGLARY PANIC TEMPORAL PULSE SOUNDING FOR FIRE e g USE ADEMCO No 702 SIREN OR 12V BELL SEE INSTRUCTIONS 30mA FA250KP 40mA FA450KP 70mA FASSOKP 70mA LOCAL PROGRAMMING MUST BE DONE WITH AN FA550KP CONNECT ED TO PARTITION 1 BUT NEED NOT REMAIN IN THE SYSTEM AND OR FA4285 VOICE MODULE 160mA AND OR No 7720 PLUS OR 7820 LONG RANGE RADIO MAY ALSO BE CONNECTED SEE INSTRUCTIONS ACCOMPANYING THOSE DEVICES OPERATION IS SUBJECT TO THE FOLLOWING TWO CON DITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT AN
63. NG OR ANY OTHER FUNCTION There are three panic key pairs or on some keypads lettered keys that if programmed can be used to manually initiate alarms and send a report to the central station Each can be individually programmed for 24 hour Silent Audible Personal or Fire Emergency responses The panic function is activated when both keys of the appropriate key pair are pressed at the same time or the appropriate lettered key is pressed for at least 2 seconds The panic functions are identified by the system as follows Displayed as Zone Notes 1 amp or A e Keys A B C are not on all keypads APA O e Key D if present is not active Important For the Silent Panic functions to be of practical value the system must be connected to a central station If relay outputs via a 4204 or 4229 or Powerline Carrier devices are used two keypad entries available to the user are included They can manually activate or deactivate the device s for starting or stopping some action such as turning lights on or off etc These keypad entries are Security Code 7 Device activates starts that device Security Code 8 Device de activates stops that device Refer to the separate instructions supplied with the Phone Module for information concerning its operating procedures Note The Phone Module cannot be used to add user codes in this system User codes must be added by using a wire
64. RINKLER 236 5TH FACTORY 126 MEDICINE 182 STATION 237 6 FAMILY 128 MONEY 184 STORE 238 6TH FATHERS 129 MONITOR 185 STORAGE 239 7 FENCE 130 MOTHERS 186 STORY 240 7TH FIRE 131 MOTION 190 SUPERVISED 241 8 FLOOR 132 MOTOR 191 SUPERVISION 242 8TH FLOW 192 SWIMMING 243 9 FOIL say NORTH 193 SWITCH 244 9TH FOYER j FREEZER 135 NURSERY T 194 TAMPER 245 Custom Word 1 FRONT o 196 TELCO A E G 136 OFFICE 197 TELEPHONE GARAGE 138 OPEN 199 TEMPERATURE 246 Custom Word GAS Ee 200 THERMOSTAT GC 142 OVERHEAD 202 TRANSMITTER 247 Custom Word 3 P U o GUN 143 PAINTING 205 UP H 144 PANIC 206 UPPER 248 Custom Word 4 HALL 145 PASSIVE 207 UPSTAIR CS HEAT 146 PATIO 208 UTILITY HOLDUP 147 PERIMETER v 249 Custom Word 5 HOUSE 148 PHONE 209 VALVE i 150 POINT 210 VAULT INFRARED de SE 212 VOLTAGE 250 Custom Word 6 INSIDE 153 POWER WwW INTERIOR 213 WALL 251 Custom Word 7 INTRUSION e Ri 214 WAREHOUSE J 216 WEST JEWELRY 156 REAR 217 WINDOW K 157 RECREATION 219 WING 252 Custom Word 8 KITCHEN 159 REFRIGERATION 220 WIRELESS 160 RF xX 6 E L 161 RIGHT 202 XMITTER 253 ustom Word 9 LAUNDRY 162 ROOM slk de rd LEFT Y a 163 3d 223 YARD 254 Custom Word 10 LIBRARY LIGHT TBE SATE 204 ZONE N LINE 165 SCREEN No LIVING 166 SENSOR 225 ZONE 167 SERVICE Note Bulleted el words in boldface type are those that are also available for use by the FA4285 Phone Module If using a phone module and words other
65. Wires from these terminals must be connected to a 9 pin connector on the control board using a 4142TR cable supplied with the 4300 transformer as shown in Figure 5 These particular wires can be 24 gauge or larger and can be run along with the AC and ground wires to the control panel 4300 TRANSFORMER INTERFACE 9 PIN CONNECTOR ON CONTROL BOARD Earth AC Ground AC Sync Data Com gt 4142TR CABLE THESE WIRES 7 8 9 NOT USED 1 2 TERMINALS ON CONTROL BOARD Figure 5 Connections of 4300 Transformer To The Control Board Installing The Back Up Battery If necessary refer to the FINAL POWER UP section for information regarding battery size to use etc A Do not attach the connector cable to the battery terminals until you are instructed to do so later in the manual 1 Place the 12 volt back up battery in the control cabinet 2 Attach Red and Black wires on the battery connector cable as follows a Red to the positive battery terminal on the control board see Summary of Connections Diagram for location if necessary b Black to the negative battery terminal on the control board U L Use a 4AH battery or larger for UL installations Earth Ground Connections The designated earth ground terminal 25 must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective The following are
66. Y INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION COMPLIES WITH FCC RULES PART 68 FCC REGISTRATION NO AC398U 68192 AL E RINGER EQUIVALENC 7B FOR COMPLETE INFORMATION SEE INSTRUCTIONS N7526 1V3 BATTERYMARCH PARK QUINCY MA 02269 PRINTED INFORMATION DESCRIBING PROPER INSTALLATION OPERATION TESTING MAINTENANCE EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM LIMITED WARRANTY Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its First Alert products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 36 months from the date stamp control on the product or for products not having a date stamp for 30 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or servi
67. ake sure that the board rests on the correct row see Detail A Swing the base of the board into the mounting clips and secure the board to the cabinet with the accompanying screws see Detail B in Fig 2 CIRCUIT BOARD DETAIL B E VIEW OF SHORT MOUNTING CLIPS DETAIL A SIDE VIEW OF CONTROL CIRCUIT BOARD SUPPORTING SLOTS BOARD Figure 2 Mounting The PC Board Mounting Control and RF Receiver Circuit Boards Together in the Cabinet 1 2 Hang two short black mounting clips provided with receiver on the raised cabinet tabs as shown in Detail B in Figure 3 Insert the top of the receiver board removed from its own case as described in its instructions into the slots at the top of the cabinet as shown in Detail A in Figure 3 Make sure that the board rests on the correct row of tabs as shown Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws see Detail B in Fig 3 Insert the top of the control s board into the slot in the clips and position two long red clips at the lower edge of the board see Detail C Swing this board into place and secure it with two additional screws Insert grounding lugs supplied with the receiver through the top of the cabinet into the left hand terminals of the antenna blocks at the upper edge of the receiver board and secure them to the cabinet top with the screws provided as shown in Detail D Insert the r
68. an s j indicates that a serial number has in fact been enrolled The cursor 10 03 1 3C RF 1s will be flashing above the loop number Press to accept the zone information NOTE If you entered 0 in the LEARN S N prompt previously you will not get an indication that the serial number has been enrolled If you want to delete the serial number enter 0 and press The system will then prompt DELETE S N Press the 1 YES key to complete the delete sequence This process deletes the serial number only not the loop number The assumption is that the proper loop number was programmed but the wrong serial or loop number was enrolled To change the loop number you must go back through zone programming for that zone and manually enter the loop number over the existing one If you want to program alpha descriptors now enter 1 YES See O are the ALPHA DESCRIPTOR PROGRAMMING section for more Zz information If not enter 0 NO ENTER ZN NUM This will return you to the ENTER ZN NUM prompt for the next 00 QUIT 11 zone When all zones have been programmed enter 00 to quit If you plan to enroll serial numbers in the sequential mode enter 00 to quit then go to the SEQUENTIAL MODE section later in this manual to enroll the serial numbers When you have finished programming all zones including all serial numbers test each zone using the system s TEST mode Do not use the AL Transmi
69. andset Telco Line O IF THE PANEL IS NOT CONNECTED TO A PROPER EARTH GROUND YOU MAY GET FALSE TELEPHONE een A l LINE CUT INDICATIONS IF THE TELEPHONE LINE 21 22 23 24 25 MONITOR HAS BEEN PROGRAMMED IN FIELD 92 TERMINALS ON CONTROL EARTH GROUND H INCOMING TELCO LINE Ms D DIRECT E Z CONNECT 3 CORD Q PREMISES m PHONES PLUG Figure 4 Telephone Line Connections Wiring The AC Transformer 1321 Wire the 1321 transformer to terminals 1 and 2 on the control board See wiring table below for wire gauge to use Caution must be taken when wiring the transformer to the control panel to guard against blowing the fuse inside the transformer the fuse is non replaceable 4300 If you are going to use a 4300 transformer interface required if Powerline Carrier devices are going to be used connect the 4300 transformer s terminals as follows a Terminals 1 3 AC and 2 Ground to control board terminals 1 2 and 25 respectively see Figure 5 See table below for wire gauge to use From the Control Panel To Use Wiring to the AC Transformer must not exceed 250 feet using 16 gauge wire The voltage reading between terminals 1 and 2 of the control must not fall below 16 5VAC or an AC LOSS message will be displayed Do not plug the transformer into the AC outlet until you are instructed to do so later in the manual 12 b Wire the other three terminals Sync Data Com on the 4300 transformer
70. aracteristics that define the way the system responds to faults on that zone Refer to the Zone Response Type section and the Zone Programming section for specific instructions on programming hard wired zones Check Out Procedure For Hard Wired Zones After installation and programming of all hard wired devices is completed each partition of the security system should be checked as follows 1 Make certain that all devices and sensors connected to the hard wired zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered use a cloth to mask them temporarily if necessary 2 Plug in the AC Transformer if you have not already done so 3 With all hard wired zones intact the Alpha keypad connected to the system should display DISARMED READY TO ARM If the following is displayed DISARMED Press to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 2000 ohm EOL resistor across the terminals of unused zones When the DISARMED READY TO ARM message is displayed you can proceed to the next step 4 Fault and then restore every contact or sensor on each zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone When each zone is restored the READY TO ARM message should appear again
71. armed in the Instant or Maximum modes no entry delay is provided Entry delay 2 is programmable from 0 99 seconds for each partition The programmed exit delay field 34 begins whenever the control is armed regardless of the arming mode selected This zone type is usually assigned to sensors or contacts on doors through which secondary entry and exit will take place and where more time might be needed to get to and from the keypad typically used for a garage loading dock or basement door Type 03 This zone type gives an instant alarm if the zone is faulted when the panel is Perimeter Burglary armed in the Away Stay Instant or Maximum modes This zone type is usually assigned to all sensors or contacts on exterior doors and windows Type 04 This zone type gives a delayed alarm using the programmed Entry Exit Interior Follower time if the Entry Exit zone is faulted first Otherwise this zone type gives an instant alarm This zone type is active when the panel is armed in the Away and Maximum modes This zone type is bypassed automatically when the panel is armed in the Stay or Instant modes This zone type is usually assigned to a zone covering an area such as a foyer lobby or hallway through which one must pass upon entry After faulting the entry exit zone to reach the keypad to disarm the system Since this zone type is designed to provide an instant alarm if the entry exit zone is not violated first it will protect an area in
72. ated common zone disarmed This allows access to a disarmed partition without compromising the security of the armed partition To define a zone as a common zone simply enter the zone number in zone list 04 using 81 menu mode as described below Common Zone Notes e When using common zones we suggest the use of the same primary subscriber account number for both partitions 1 and 2 This will help monitoring stations to better track event involving common zones e The common zone will sound and report alarms only if both partitions are armed i e if one of the partitions is disarmed and the other partition is armed a fault on this zone will not cause an alarm When only one partition is armed the common zone is automatically treated as if it were a zone type 23 no alarm response zone e If either partition is armed and the other is in chime mode the common zone keypad will not chime upon faults The common zone will chime if both partitions are disarmed and either partition is in chime mode e A fault on the common zone is displayed in both partitions e Either partition may arm its system if the common zone is faulted but once armed the other partition cannot arm That partition must first bypass the common zone or correct the fault before arming e Either partition can clear and restore the common zone after an alarm e After both partitions arm exit error logic if enabled in field 59 will activate if the common zone re
73. ber if expanded or 442 reporting is selected NOTE OPEN reports are not sent in if the associated closing report is not enabled 53 RESTORE REPORT CODES 70 76 67 68 70 71 72 73 74 75 76 89 90 RF XMTR LOW BATTERY REPORT CODE 010 This is sent in the event that a wireless transmitter low battery condition exists See box CANCEL REPORT CODE See box on previous page 010 This is sent upon disarming of the system after an alarm condition was reported ALARM RESTORE REPORT CODE 1st DIGIT 0 This is sent when the zone that caused an alarm is restored to its non faulted condition 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field 56 if expanded or 4 2 reporting is selected TROUBLE RESTORE REPORT CODE 010 See box This is sent when a trouble in a zone is restored BYPASS RESTORE REPORT CODE 010 See box This is sent when a zone that has been bypassed is un bypassed AC RESTORE REPORT CODE 0 10 This is sent when AC power has been restored after an AC power outage See box Reports with Partition 1 Subscriber No LOW BAT RESTORE REPORT CODE 010 This is sent when a system low battery condition is restored to normal See box on previous page Reports with Partition 1 Subscriber No RF XMTR LOW BATTERY RESTORE CODE 0 10
74. bled The loss of the line can optionally cause a local display or a display and trouble sound Event Logging feature keeps a record of selected events in a history log up to 48 events All control and readout from the log is done via First Alert Professional FADL software only Provides a 12VDC 2 AMP output that can drive the compatible sounders listed in the EXTERNAL SOUNDERS section assumes a fully charged battery is connected Steady output for Burglary Panic or temporal pulse output 3 pulses pause 3 pulses pause 3 pulses for Fire Uses current limiting circuitry for protection Auxiliary Power Output Programming Provides 12VDC 600 mA maximum Uses current limiting circuitry for protection This output interrupts for smoke detector reset if 4 wire smoke detectors are used Programmed options are stored in electrically erasable non volatile EEROM memory information can be reprogrammed at any time and will not be lost in the event of a power loss The system can be uploaded downloaded or controlled via an IBM compatible computer FADL software and a HAYES modem specified by Ademco Keypad programming consists of Data field programming Interactive menu mode programming For programming from a keypad a FA550KP 2 line Alpha keypad must be connected to partition 1 but need not necessarily stay in the system Communication Formats Supported Zone Descriptors Ademco
75. button transmitters RF keys such as the 5804 5803 and 5801 you must assign a unique zone number to each individual button used on the transmitter Each button on the transmitter also has a pre designated loop or input number which is automatically displayed Programming an RF House ID 01 31 in field 24 is necessary only if using 5827 5827BD wireless keypads or 5804BD transmitters An RF House ID is not necessary for other 5800 series transmitters and the entry should be left at 00 default in those cases The 5827 reports low battery status as zone 00 Transmitter Supervision Except for some transmitters that may be carried off premises 5802 5802CP 5804 5804BD 5803 and 5827 and 5827BD each transmitter is supervised by a check in signal that is sent to the receiver at 70 90 minute intervals If at least one check in is not received from each supervised transmitter within a 12 hour period the missing transmitter number s and CHECK will be displayed The supervision for a particular transmitter in the system that may also be carried off the premises 5801 5802MN may be turned off by enrolling it as a UR unsupervised RF type as described later 5800 series transmitters have built in tamper protection and will annunciate as a CHECK condition if covers are removed 25 Transmitter Input Types All of the transmitters described have one or more unique factory assigned input loop ID codes Each
76. by this function will be displayed after the bypass is initiated UL installations must be 0 no forced bypass 24 RF HOUSE ID CODE 00 disable all wireless keypad usage 01 31 House ID for partition 1 The House ID identifies receivers and wireless keypads If a 5827 or 5827BD Wireless keypad or 5804BD transmitter is to be used a House ID code MUST be entered and the keypad should be set to the same ID Partition 2 House ID partition 1 ID 1 use 01 30 for partition 1 if wireless keypads are used in both partitions 25 WIRED ZONE EXPANSION 0 0 no expander module connected 1 4219 connected 2 4229 connected 3 4204 connected 26 CHIME BY ZONE o 0 no chimes on fault of any entry exit or perimeter zone when chime mode activated 1 yes chimes on fault of specific zones programmed in relay zone list 3 when chime mode activated This option allows the installer to define the specific zones intended to chime when faulted while the system is in chime mode 47 27 28 29 31 32 POWERLINE CARRIER DEVICE X 10 HOUSE ID 0 Powerline Carrier devices require a House ID This field identifies this House ID to the control If Powerline Carrier devices are used they are selected in field 80 House ID is entered in following manner 0 A 1 B 2 C 3 D 4 E 5 F 6 G 7 H 8 1 9 J 10 K 11 L 12 M 13 N 14 0 4 15 P
77. caida adds 10 Caller DOE saciar iris 33 34 Cancel Report Code i s Ee ostias 54 Central Station ii 52 Character Ascii Chart oooooooccnoncccnoocncooonncnoncnononcncnnnnss 70 Character Chart geste ESE R GER SEENEN 66 Character List lona Se ee 69 Charging Voltage ooconoocccnooccnooonnnonnnnnonnnononnnnnnnnnonanonnnnns 89 Check In Signal aladdin 25 Chime Mode una 80 COMMON ZONE ese ee Ea i eiA 7 65 Communication esse RR RA Re ee 89 Communication Failure eise sees se RA ER ee 82 Communication Formats Supported esse esse 9 Compatible 2 Wire Smoke Detectors sesse ese 18 91 Compatible Glass Break Detectors esse esse esse 19 Compatible Sounders iis RA RA RA RA 36 Confirmation Of Arming Ding e sees sees se ee 49 Contact ID senal ts 38 52 78 Contact ID Event CodeS sesse ese Re RA Re 78 Contact ID Reporting sesse esse Re AR Re 89 Control Cabinet ui heh eit chk eed Ee N Ge See 10 Control s Circuit Board esse RA EA 11 Custom Words esse Ee SCENE ed ie 69 70 Default Descriptor ees esse Re Re Re Re ee 67 Device Address n SS NE Es GP Ge n EE se 21 Dialer Programming 50 DIP Switches iis RR 21 24 25 28 29 Disarm EE 46 Disarmed Not Ready oooconoocccnoccconoconoonnncnnnnncnonnncnonnnonno 80 Disarming EE MI EE Ed 80 Download Information 55 Download Phone Number c ocooooccnoocnnononnnononncnonnnnnnnnncnnno 55 Downloader nasa dan 25 Duress Os ls inicie 8 Eagle IL tata 39 Earth Gr
78. ced by anyone other than First Alert factory service For warranty service return product transportation prepaid to First Alert Factory Service 165 Eileen Way Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARIS
79. cess A Phone Access User s Guide for phone access to the security system is provided with the Phone Module for the user of the system Mounting The FA4285 Phone Module The Phone Module may be mounted in the control cabinet if space is available or if this is not possible on the side of the cabinet or adjacent to it When mounting the Module outside the cabinet use the screw holes at its rear which will permit it to be mounted horizontally or vertically 2 faced adhesive tape may be used if preferred Wires can be brought out from the side or back a round breakout is also available on the back Affix the Phone Module s connections label supplied separately to the inside of the Phone Module s cover if the cover is used If you have installed the module within the cabinet affix the label to the inside of the control cabinet s door AUDIO ALARM VERIFICATION AAV UNIT section for the wiring connections required when using both a Phone Module and an AAV unit If you are not using an AAV unit follow the wiring connections indicated in this section for the Phone Module A If you are also using an Audio Alarm Verification AAV unit refer to the 32 Phone Module Wiring The FA4285 is wired between the control panel and the premises handset s It listens for touch tones on the phone line and reports them to the control panel During on premises phone access it powers the premises phones during off premises phone access
80. ction with a magnet Enroll as 3 for RF supervised 5849 Glassbreak Enroll as 3 for RF supervised Detector Transmitter 5890 PIR Detector Enroll as 3 for RF supervised Transmitter The cover must be on the unit when enrolling the serial number When enrolling a transmitter s ID code s any PIR that may be in the vicinity and is not being enrolled should be covered with a cloth tissue etc to prevent activation of that PIR 27 Installing 5800 Series Transmitters To be sure reception of the transmitter s signal at the proposed mounting location is adequate perform a Go No Go test Go No Go Test Mode The Go No Go tests will verify adequate RF signal strength from the proposed transmitter location and allow you to reorient or relocate transmitters if necessary before mounting the transmitters permanently This mode is similar to the transmitter test mode except that the wireless receiver gain is reduced This will enable you to make sure that the RF signal from each transmitter is received with sufficient signal amplitude when the system is in the normal operating mode 1 5 6 With at least one 2 line Alpha keypad FA550KP connected to the system power up the system temporarily If you had previously connected the AC transformer to the control panel you need only plug in the transformer to 120VAC outlet to power up the system Enter installer code 4112 4 f
81. d in field 56 but we recommend that it be done using 82 menu mode To program zone descriptors you simply enter the 3 digit reference number for the desired word s The 3 digit number for each word is provided in the Alpha Vocabulary list on a following page 1 With the system powered up enter the programming mode by keying Installer code 4 112 8 0 0 The following display will appear Installer Code 2 Press 82 0 No 1 Yes The Program Alpha prompt will appear Program Alpha 6671 Custom Words gt Gen Se M o 0 No 1 Yes 00 The Custom Words prompt wi appear 4 Press 0 No The system will then automatically display the descriptor for zone 1 The procedure for adding custom words to the built in vocabulary will be found later under Adding Custom Words 66 Summary Mode Display Default Descriptor If a descriptor was not entered previously for zone 1 the default ZN 01 ZONE 01 descriptor for zone 1 will be displayed Note that this a summary mode and that no entries can be made Entries can be made only when the display contains a flashing cursor which signifies the entry mode Flashing Cursor system is 5 To delete or change the default ready for entry of word descriptor for zone 1 press plus the same zone number 01 This will clear that descriptor and allow ZN 01 changes to be made at the flashing cursor NOTE If you do not wi
82. d in non removable electrically erasable non volatile EEROM memory These must be programmed for the particular installation to establish its specific alarm and reporting features It is possible to program the system at any time even at the installer s premises prior to the actual installation Simply apply power temporarily to the control and then program the unit as desired IMPORTANT You cannot enter the programming mode unless both partitions are disarmed There are two programming modes data field programming and interactive menu mode programming Data field programming is used for setting various system options and interactive programming is used for programming zone information programming relay outputs and for enrolling transmitter serial numbers A To program the system you must use a FA550KP 2 line Alpha keypad connected to the Partition 1 keypad terminals on the control 4 5 6 amp 7 Also both partitions must be disarmed The Alpha keypad need not necessarily remain in the system after programming Programming can also be performed remotely from the installer s office home using an IBM personal computer a modem and FADL downloading software See the REMOTE PROGRAMMING AND CONTROL DOWNLOADING section Entering Program Mode You may use one of the following methods a Press both the and keys at the same time within 50 seconds after power is applied to the Control or b After power up
83. d keypad e A display of CANCEL ALARM or CA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended e g exit door left open but the system was disarmed during the entry delay time The alarm sounder and keypad sound continuously but stop when the system is disarmed No message will be transmitted to the central station e A display of EXIT ALARM or EA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended but the system was NOT disarmed during the entry delay time The alarm sounder and keypad sound continuously until the system is disarmed or timeout occurs An exit alarm message is sent to the central station e The EXIT ALARM display etc will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay In any of the above cases use a second OFF sequence code plus OFF key to clear the display 81 Trouble Conditions See Troubleshooting Guide also General Information Check and Battery Displays Telephone Line Failure Power Failure Other Displays Fixed Word displays are in parentheses The word CHECK on the Keypad s display accompanied by a rapid beeping at the Keypad indicates that there is a trouble condition in the system The audible warning sound can be silenced by pressing
84. d should be in agreement with you and the central station office receiving the signals Use these guidelines to program this entire section With a 3 1 or 4 1 Standard Format Enter a code in the first box 1 9 A B C D E or F Enter 10 for A this reports a 0 on some receivers 4411 for B 12 for C 13 for D 14 for E 15 for F An entry of 0 in the first box will disable a report An entry of 0 in the second box will result in automatic advance to the next field when programming With an Expanded or 4 2 Format Enter codes in both boxes 1st and 2nd digits for 1 9 or A F as described above An entry of 0 in the first box will disable a report An entry of 0 in the second box will eliminate the expanded message for that report With Ademco Contact ID Reporting Enter a digit in the first box to enable the zone to report Use a different digit for each zone until you have used up available digits If the number of zones exceeds the number of available digits begin with digit 1 again This is an enabling code only and is not the actual code sent to the central station office Entries in the second boxes will be ignored For system status non alarm codes enter a 1 in the first box for all the system conditions you want to send to the central station An entry of 0 in the first box will disable the report BH SYSTEM STATUS REPORT CODES k59 68 59 60 61 62
85. de activate Ifa SYSTEM OPERATION is chosen that operation will cause the device to de activate The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Relays amp Powerline Carrier devices later in this section and in the Programming Form Partition No P The device s Stop Zone Type System Operation may be limited to an occurrence on Partition 1 Partition 2 or any partition During normal system operation any devices may be manually started by keypad entry of Code 7 n or manually stopped by keypad entry of Code 8 n gt where n the device number to be controlled As a minimum the ACTION A and PARTITION No P fields must be programmed for this manual action to be If a relay is energized before a 4 wire smoke detector is reset the relay will be stopped by the interruption of Aux Power that resets the smoke detector If this is not desired the power to the relay unit should be supplied from another 12V power source e g the same source that is powering external equipment through the relay contacts 62 Output Device Displays Enter Device No 00 Quit 01 02 Start Zn Typ Not Used 00 Use 0 Any for kk Partition No P entry Or at Disarming whichever occurs earlier Programming Output Relays and Powerline Carrier Devices While in program mode press 80 to enter Output De
86. de now by either entering 1 YES or by 0 NO 1 YES 0 pressing the upper left hand button of the program tool If using the program tool move to the physical location of the transmitter to be enrolled before pressing the button A single short beep will verify that the button has been pressed The system will respond to the first serial number transmitted after the key on the keypad or the button of the program tool is pressed Enter 0 NO if you wish to enroll the transmitter later using the 83 sequential mode described in the SEQUENTIAL MODE section later in this manual If 0 is entered skip to the summary screen prompt 10 INPUT S N L This prompt is displayed if 1 YES is entered in response to the i Learn S N prompt The serial number may be enrolled by one of AXXX XXXX two methods a Enter the 7 digit serial number printed on the transmitter using an alpha keypad or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc 10 INPUT S N L The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the A002 4064 1 serial and loop numbers and cause the keypad to beep twice 7 If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system will not
87. deal Model 61 035 or equivalent available at most electrical supply stores AC Power Up 1 Plug the 1321 or 4300 transformer into a 24 hour uninterrupted 120VAC outlet 2 Following power up AC dl disabled or Busy Standby Alpha keypads or NOT READY fixed word keypads will be displayed Also the green POWER LED on the keypad s should light Some keypads are equipped with a READY LED in place of a POWER LED After approximately 1 minute the initial displays will revert to DISARMED READY TO ARM for Alpha keypads or READY for Fixed word keypads if there are no faulted zones This 1 minute delay allows PIRs etc to stabilize To bypass this delay press 0 Connecting The Back Up Battery In the event of an AC power loss the Control panel is supported by a back up rechargeable gel cell battery The minimum battery size recommended is the No 467 12V 4AH battery See Calculating Battery Size Needed below The battery is installed in the control cabinet The standby battery is automatically tested every 4 hours beginning 4 hours after exiting programming mode In addition entry into the test mode will cause a battery test to be initiated Calculating the Battery Size Needed Determine the total device current draw after filling in the AUXILIARY DEVICE CURRENT DRAW WORKSHEET on the next page To this figure add the 100 mA that is drawn by the control panel itself Then to determine the bat
88. display the serial number but will wait for a transmission from another transmitter or transmitter loop input The system will then enter an optional confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone When the system sees activity on the appropriate input it will beep ne three ti d display the confirmati AO ree times and display the confirmation message ONFIRMED 22 4064 1 At any time during this step you may press the key on the keypad or L the upper left hand button of the program tool if you are satisfied with the serial and loop number combination that has been enrolled regardless of whether or not the enrolled input has been confirmed If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the LEARN S N prompt A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 YES or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop 59 ZN ZTP RC IN L The summary screen for the zone will appear Note that
89. dule is disconnected from the control s terminals 4 5 6 amp 7 99 RELAY CONNECTOR RELAY DIP SWITCH FOR SETTING ADDRESS AND ZONE A RESPONSE l bk EITHER OR BOTH CAN BE USED E A RELAY P Mor Ne 4 PIN CONSOLE PLUG TERMINALS ON CONTROL PANEL DATA OUT TAMPER JUMPER POSITION v O WH gt TERM 6 4229 IN CABINET NOT TAMPERED o S GROUND TERM 4 o 4229 REMOTE iy 3 TAMPER PROTECTED ai ol gt TERMS o o TERM 7 s CONTROL niy Ga REED TERMINATE EACH TAMPER PROGRAMMED ZONE EE a WITH 1000 OHM 1K Ay S SWITCH END OF LINE RESISTOR EACH ZONE S MAX _ LOOP RESISTANCE 300 OHMS E O L G H ZONES A B C D E F Figure 13 4229 Connections to Control 4204 DIP SWITCH FOR SETTING DEVICE ADDRESS AND ENABLING DISABLING TAMPER RELAY 4 TYPICAL SHOWN OFF o ODQOOOOODOOONY ps m lt COVER TAMPER REED SWITCH 4 PIN CONSOLE PLUG m NE Le EITHER OR BOTH CAN BE USED TB1 ps Le DATA IN FROM CONTROL GROUND DATA OUT TO CONTROL 12V Figure 14 4204 Connections to Control Powerline Carrier devices UL EL Powerline Carrier devices and the 4300 transformer are not UL Listed for fire or burglary functions and are intended for home automation When usin
90. e These conditions apply only when a zone list is used The different choices for EVENT are listed below and in the Programming Output Relays amp Powerline Carrier devices section that follows e ALARM Relay activates upon any alarm in an assigned zone in the zone list e FAULT Relay activates upon any opening or short in an assigned zone in the zone list e TROUBLE Relay activates upon any trouble condition in an assigned zone in the zone list e NOT USED Relay action is not dependent upon one of the above events 2 Zone List ZL is a group of zones to which the EVENT applies in order to activate a particular device Note that there are a total of 3 output device related zone lists that can be programmed in 81 menu mode when the selected EVENT Alarm Fault or Trouble occurs in any zone in the selected Start ZONE LIST 1 2 or 3 activation of the selected device will START Start by Zone Type or System Operation 1 Ifa System Operation such as DISARMING or ANY FIRE ALARM is to activate the device the appropriate choice would also be entered under the ZONE TYPE option ZONE TYPE is used independently of the EVENT ZONE LIST combination If a ZONE TYPE is chosen any zone of that response type going into alarm trouble or fault will cause the device to activate as selected in ACTION If the same ZONE TYPE is also chosen for the STOP programming any zone of that
91. e 10 Figure 2 Mounting The PC Board sesse sesse ee sed se ee se ee ee RA de Ad AA conos 11 Figure 3 Mounting the PC Board amp RF Receiver Together in the Cabinet 11 Figure 4 Telephone Line Connections esse sesse ee AA AA ee ee ee 12 Figure 5 Connection of 4300 Transformer to the Control Board 06 13 Figure 6 Keypad Connections to the Control Board 15 Figure 7 Using a Supplementary Power SupplY siese sesse sesse ds see ee ee ee 16 Figure 8 2 Wire Smoke Detector Connected to Zone 1 18 Figure 9 4 Wire Smoke Detector Connections Zones 221 18 Figure 10 Glass Break Detector Connections to Zone 8 19 Figure 11 Wiring Connection 4219 amp 4229 4229 shown esse sesse se ee 21 Figure 12 5881 5882 RF Receiver cover removed sesse esse sees se se see ee ee 24 Figure 13 4229 Connections To Control ooonooccnnocanicaconoccconnnon Ged AA ee ee de 30 Figure 14 4204 Connections To Control sees ss esse ee ee Ged RA ee ee ee de 80 Figure 15 4300 Transformer Wiring Connections iese esse ee se se de se Ge ee ee 31 Figure 16 FA4285 Phone Module Wiring Connection 34 Figure 17 Typical Sounder Wiring sesse see see AA Gee ed ed AA ee ed ee cate 87 Figure 18 Long Range Radio Connections iis see ss ses ee Gee de AA AA ee ee ee 88 Figure 19 NOT USED Figure 20 Connection of AAV Unit Without an FA4285 Phone Module 40 Figure 21 Connection of AAV Unit With an FA4285 Ph
92. e Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed Smoke could be blocked by the closed door Also an alarm in the hallway outside may not wake up the sleeper if the door is closed e Install a smoke detector inside bedrooms where electrical appliances such as portable heaters air conditioners or humidifiers are used e Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet 12 meters long e Install smoke detectors in any room where an alarm control is located or in any room where alarm control connections to an AC source or phone lines are made If detectors are not so located a fire within the room could prevent the control from reporting a fire or an intrusion THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES DINING LIVING ROOM BEDROOM IB Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection A Heat Activated Detectors BEDROOM Recommendations For Proper Intrusion Protection For proper intrusion coverage sensors should be located at every possible point of entry to a home or commercial premises This would include any skylights that may be present and the upper windows in a multi level building In addition we recommend that radio backup be used in a security system so that alarm signals can still be sent to the alarm
93. e Sniffer mode If so wait a few minutes and try again The keypads in both partitions will display all zone numbers of wireless units in both partitions programmed into the system As the system receives a signal from each of the transmitters the zone number of that transmitter will disappear from the display The transmitter codes may be checked upon installation or in an installed system All the wireless zone numbers should disappear after about 1 1 2 hours Notes e All BR type units must physically be activated to clear the display 83 e When one button of a transmitter RF UR or BR is activated all zones assigned to other buttons on that transmitter are cleared This also applies to 5816 and 5817 transmitters which have multiple loops zones e Any transmitter that is not enrolled will not turn off its zone number Exit this mode by keying Installer code OFF b GO NO GO TEST MODE By pressing Installer code 4 4 on partition 1 s keypad a mode similar to the user test mode code TEST is entered but the wireless receiver gain is reduced Checking in this mode assists in determining good mounting locations for the transmitters when the system is being installed and verifies that the RF transmission has sufficient signal amplitude margin for the installed system Exit the mode by entering Installer code OFF NOTE System Test Mode code test will be automatically terminated after 4 hours if th
94. e entered before sounding alarm upon entering UL installations must be set for a maximum of 20 seconds AUDIBLE EXIT WARNING 1 1 0 no exit warning sound Part 1 Part 2 1 provide exit warning sound when armed AWAY Warning sound consists of slow continuous beeps until last 5 seconds when it changes to fast beeps The warning sound will end at the termination of Exit time CONFIRMATION OF ARMING DING 0 0 0 no ding Part 1 Part 2 1 confirmation ding after arming system 2 confirmation ding after arming from RF button or RF keypad only ding occurs when the system receives the RF transmission Confirmation of arming is 1 2 second external sounder ding when closing report is sent or at the end of exit delay POWER UP IN PREVIOUS STATE 1 0 always power up in a disarmed state 1 assume the system status prior to power down When the system powers up armed an alarm will occur 1 minute after arming if a zone is faulted Note that if the previous state was armed AWAY or STAY the system will not respond to sensor changes for 1 minute which allows time for sensors such as PIRs to stabilize UL installations must be 1 power up in previous state 49 DIALER PROGRAMMING 4050 Fields 40 41 42 Enter up to the number of digits shown Do not fill unused spaces Enter 0 9 11 for 12 for 13 for a pause 2 seconds
95. e es se ee Ges ee ee ee ee ee ee Ge ee ee ee 75 SYSTEM COMMUNICATION sees ee NEEN EE EE GEES ee RE NG EA se 76 Report Code Rormate ia N ee tints nih hin Nee RNS 76 Table of Contact ID Codes ivi cscs idsceccsccceec eke gek Rotes iTe koe es NE ee gee ee SEE EE Ge Ke be dk eds 78 Section 23 SYSTEM OPERATION ese ee se se se se ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee rr anar anar anar ee ee ee ee ee ee ee oes 79 Security Gode esse se EE rad 79 Key pad Functions EE AE SE Ge Ee Ee se ETRE fe DC 80 Trouble Conditions a earren E a RE EG ENEE 82 Section 24 TESTING THE SYSTEM 83 BK EEN 83 Toth Install ii A A a ii ee eg 84 Section 25 TROUBLESHOOTING GUIDE 85 Contacting Technical Support In The Event Of Problem 87 REGULATORY AGENCY STATEMENTS AA 88 Section 26 SPECIFICATIONS ACCESSORIES esse ese se ee ae eras ese esse se ee se ee see rn de ee ee seese 89 e ee EE 89 Accessories Compatible Devices oooccconoccnonooocanono cononnnonnnnnnnnnnnnncnnnnnnnnon AA ee RA ee 91 APPENDIX A 5800 RF System Wireless Transmitters Input Loop Identification Diagrams 92 Made iaa 94 Limitations Of This Alarm System 98 Summary Of Connections oooooccnnoccncnonoccnnnnnnn conoonnnnnnnnnnnnnnnnnnnnnnnnnno Ge ee AA ee RA Se RA AR Ge AA AA ee 99 TiimitedWarrantY EG a a dada 100 Programming FOFD EE Insert LIST OF FIGURES Figure 1 Installing the Cabinet Lock iss see see se Ge Re AA AA AA ee e
96. e installer or user does not manually terminate it This insures that Fire and Panic zones will not remain disabled However Sniffer Mode installer code 3 does not automatically expire You must manually exit installer code OFF sniffer mode to return to normal operation Sniffer Mode also terminates if a user arms the system TO THE INSTALLER Regular maintenance and inspection at least annually by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts Recommendations must be included for a specific program of frequent testing at least weekly to insure the system s proper operation at all times 84 Section 25 TROUBLESHOOTING GUIDE SYSTEM including Wireless received at 5881 5882 Transmitter zone number appears during Transmitter Sniffer mode but does not clear Low Battery message on keypad Periodic beep s from keypad With 5800 System no response to a transmitter in normal operation although zone number clears during Transmitter Sniffer mode Nuisance or phantom alarm Intrusion alarm for no apparent reason CHECK and zone number 2 8 is displayed Transmitter or 5881 5882 not properly
97. e sound when line is faulted Each partition turns off its own trouble sound No automatic timeout 3 Same as 2 above plus Device No 2 STARTS If either partition is armed external sounder activates External sounder will be turned off by normal bell timeout or by security code plus OFF from either partition it does not have to be the one that was armed NOTE Option 3 may be used even if a relay unit or Powerline carrier device is not connected to the control Device number 2 must either be programmed to be STOPPED in field 80 or STOPPED by entry of security code 8 2 Partition in 80 should be set to 0 for STOP NOTE This feature will not function properly unless the designated earth ground terminal 25 is connected to an earth ground If it is not you may get false line cut indications 93 94 NUMBER OF REPORTS IN ARMED PERIOD 0 0 reports limited to a total of 10 1 unlimited number of reports This option can be used to limit the number of messages alarm amp alarm restore reports sent to the central station in an armed period UL installations must be 1 unlimited reports DOWNLOAD PHONE NUMBER Enter up to 16 digits as follows 0 9 11 for 12 for 4 13 for a pause Do not fill unused spaces End field by entering To clear entries from field press 94 55 NOTE If 15 is entered in field 95 to b
98. e system on the premises includes a Caller ID unit connect the unit directly to the Handset terminals 21 amp 22 on the control as shown IMPORTANT IF THE PANEL IS NOT CONNECTED TO iA PROPER EARTH GROUND YOU MAY GET FALSE LINE CUT INDICATIONS IF TELEPHONE LINE MONITOR HAS BEEN PROGRAMMED Incoming Handset Telco Line a Z 2 O CO H H H H L TERMINALS ON CONTROL CALLER ID UNIT AS Go CG If IMPORTANT NOTE FOR BE EXISTING INSTALLATIONS o Io EXISTING WIRES Z Z B CONNECTED TO THE 9 i a ES HANDSET TERMINALS ON hd IS PREMISES ANSWERING CONTROL MUST BE MOVED 9 3 vz CANADA MACHINE AND PHONES FROM THERE TO TERMINALS S6 5 3 AND 4 ON THE 4285 ANSWERING MACHINE TO GND 4285 TERMINAL 25 VOICE MODULE ON CONTROL NOT INSTALLER a ADJUSTABLE H KEYED em HEADER NOTE IF THE TELEPHONE HAS BUILT IN CALLER ID THE CALLER ID FUNCTION MAY NOT WORK 6 AUDIO OUT 1 UNUSED YELLOW TO DATA OUT term 7 TO CONTROL HE EE cieas i 4285 i eestor on i TERMINAL ASSIGNMENTS __ CONNECTOR RED TO AUX term 5 TERMINALS AA ASS MEN IS WITH FLYING BLACK TO AUX GROUND term 4 USED FOR a PHONE INPUT LEADS GREEN TO DATA IN term 6 KEYPAD i S S e ee PHONE OUTPUT CONNECTIONS 4 RING ONE OUTPU 5 GROUND i I L J FOR FUTURE USE Figure 16 FA4285 Phone Module Wiring
99. eceiver s antennas through the top of the cabinet into the blocks right hand terminals and tighten the screws Refer to the WIRELESS ZONE EXPANSION section for setup and wiring of the receiver HOLES FOR ANTENNAS AND GROUNDING LUGS k BOARD SUPPORTING SLOTS J OO A OP d RECEIVER CIRCUIT BOARD CIRCUIT BOARD SeeDetailD CABINET DT OD DETAIL A HORT MOUNTING CLIP SIDENI ei BOARD SUPPORTING SLOTS B CONTROL N CIRCUIT BOARD El H x LONG MOUNTING CLIPS H DETAIL B SIDE VIEW OF SHORT MOUNTING CLIPS SCREW ap fac ANTENNA DETAIL C GROUNDING LUG SIDE VIEW OF a LONG MOUNTING CLIPS i d DETAIL D Weg ANTENNA AND GROUNDING LUG INSTALLATION S x CABINET Figure 3 Mounting The PC Board And RF Receiver Together In The Cabinet 11 Standard Phone Line Connections Module is used Refer to the FA4285 Phone Module section for information A The wiring connections shown here are not applicable if the FA4285 Phone regarding phone line connections which are different than those shown here Incoming phone line and handset wiring is connected to the main terminal block via a RJ31X jack as follows also see Figure 4 Term 21 Local Handset TIP Brown Term 22 Local Handset RING Gray Term 23 Incoming Phone Line TIP Green Term 24 Incoming Phone Line RING Red Colors of wires in Direct Connect Cord Incoming 2 IMPORTANT H
100. ed expansion and or wireless zones plus 3 keypad activated zones Basic Hardwired Zones Provides 8 basic hardwired zones having the following characteristics e EOLR supervision supporting N O or N C sensors e Programmable response time 10 350 or 700 milliseconds e Individually assignable to either partition e Up to sixteen 2 wire smoke detectors on zone 1 e 4 wire smoke or heat detectors on zones 2 through 7 as many as can be powered from AUX power on the control e Up to fifty 2 wire latching type glassbreak dets on zone 8 w auto reset Optional Expansion Zones up to 30 total wired and wireless Wired Expansion Supports up to 8 additional wired zones using a 4219 expansion module or 4229 expansion relay module These zones have the following characteristics e EOLR supervision supporting N O or N C sensors e 300 500 msec normal response with an option for fast 10 15 msec response on loop A first expansion zone Wireless Expansion Supports up to 30 wireless zones less if using wired expansion zones e Requires the use of a 5881 5882 in Canada type RF Receiver as indicated below Receiver Model No of Zones 5881L 5882L Up to 8 5881M 5882M Up to 16 5881H 5882H Up to 30 e Requires the use of 5800 series wireless transmitters Two Partitions e Provides the ability to control two separate areas independently each area functioning as ifit had its own separate control e Zones including wireless assignable to either partitio
101. edure Check programming switches on transmitter Check with all occupants of protected home Check setting of entry and exit delays Check all openings for proper switch and magnet orientation Check the sensor or the loop wiring in the affected zone The system will not arm until this condition is corrected or the affected zone is bypassed TROUBLESHOOTING GUIDE continued CONTROL POSSIBLE CAUSE AC POWER light off la Interrupted AC power supply la Check transformer connection and Powerline circuit breaker 2 Digital communicator a FA162C in TEST mode a Remove from TEST mode message not being received Telephone connection not secure Check all connections 2c Digital communicator malfunctioning 2c Check with a different FA162C 2d Telephone number in program needs 2d Program prefix or access code into the prefix or access code FA162C 2e Telephone call to central monitoring 2e FA162C system cannot work in this station requires operator assistance situation 3 Does not arm properly 3a Ready light not on 3a Check for faulted zones and make intact or use Bypass arming if desired d FA162C doesn t respond to da CC or MODEM COMM displayed 4a System is in communication with keystrokes on keypad downloader at central station Wait until download session is finished 4b d1 or Busy Standby displayed 4b System has just been powered and is in its one minute initialization To bypass thi
102. entering 56 the following prompts are displayed If the system has been set up to use wireless transmitters and a program tool has been entered skip to the zone number prompt If no program tool has been entered the following prompt will appear If a program tool 5803 5804 is being used enter 1 If not using a NS E e tool enter 0 and skip to the zone number prompt 00 INPUT S N L If 1 is entered the system will prompt for the serial number of the transmitter being used as the program tool You can enter the serial AXXX XXXX number using one of the following methods a Enter the 7 digit serial number for the transmitter or b Press any button on the transmitter The keypad should beep twice and display the serial number of the tool In this example the serial number is A123 4567 Once entered you can use the 5803 5804 program tool to ready the system for enrolling A123 4567 3 a transmitter s serial number by first pressing the upper left hand button of the program tool then activating the desired transmitter see procedure at the LEARN S N prompt To back up to the PROGRAM TOOL prompt press the key on the keypad The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool Press to continue 00 INPUT S N L 57 Enter Zn Num 00 Quit 10 Zone 10 entered Zn ZIP RC In L 10 03 1 10 R
103. entral station for change of function or status verification Comm Failure FC A communication failure has occurred Open Circuit OC The keypad is not receiving signals from the control and sees an open circuit Long Rng Trbl bF Back up LRR communication failure 82 Section 24 TESTING THE SYSTEM Test Procedure After installation is completed each partition of the Security System should be carefully tested as follows 1 With the System in the disarmed state check that all zones are intact If a NOT READY message is displayed press the key to display the faulted zone s Restore faulted zone s if necessary so that READY message is displayed Fault and restore every sensor individually to assure that it is being monitored by the system 2 Enter the security code and press the TEST key The outside sounder will sound for 1 second The keypad should sound 3 beeps each time a contact is faulted A test report should be transmitted if programmed to the Central Station immediately If the backup battery is discharged or missing the sounder may not turn on and a LOW BATTERY report will be transmitted with a TEST report The keypad will beep once per minute as a reminder that the system is in the Test Mode To turn off the test mode enter security code and press the OFF key Note Triggering a zone set to Arm Away Arm Stay or Disarm will take the system out of TEST and cause that action Alarm messages will be sent
104. entries xh Powerline Carrier devices require the use of optional 4300 transformer module instead of the supplied 1321 AC transformer Optional Phone Module Paging Feature Supports the Ademco FA4285 Phone Module on Partition 1 only Provides access to the system via on premises or off premises phones for arming disarming etc plus control of relay outputs and Powerline Carrier devices If programmed the paging feature allows certain system conditions to be reported to a pager where a 10 digit code indicates the type of condition that has occurred Audio Alarm Verification Option Provides a programmable Audio Alarm Verification AAV option which can be used in conjunction with an output relay to permit voice dialog between an operator at the central station and a person at the premises Requires the use of optional AAV unit such as Eagle model 1241 U L The AAV option may not be used in UL installations 8 Optional Long Range Radio Allows all messages that have been programmed to go to the primary telephone number to be reported additionally to a 7720PLUS or 7820 radio Check availability of these models Built in Telephone Line Monitoring Option Event Logging Alarm Output The telephone line voltage can be monitored to supervise the phone line connection The panel must be connected to a proper earth ground or you will get a false line cut indication if this feature is ena
105. eption which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Ifusing an indoor antenna have a quality outdoor antenna installed Reorient the receiving antenna until interference is reduced or eliminated Move the radio or television receiver away from the receiver control Move the antenna leads away from any wire runs to the receiver control Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment FEDERAL COMMUNICATIONS COMMISSION FCC Part 68 STATEMENT This equipment complies with Part 68 of the FCC rules On the front cover of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested thi
106. eristics that define the way the system responds to faults on that zone Refer to the Zone Response Type section and the Zone Programming section for specific instructions on programming wired expansion zones Check Out Procedure For Wired Expansion Zones After you have completed installation and programming of all devices all expansion zones in each partition of the security system should be checked as follows 1 Make certain that all devices and sensors connected to the wired expansion zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered use a cloth to mask them temporarily if necessary Plug in the AC transformer With all zones intact including hard wired zones the Alpha keypad connected to the system should display DISARMED READY TO ARM If the following is displayed DISARMED Press to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 1000 ohm EOL resistor across the terminals of unused expansion zones on the 4219 or 4229 module When the READY TO ARM message is displayed you can proceed to the next step Fault and restore every contact or sensor in each expansion zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone When each zone is restored
107. ers e Do not locate the cabinet in an area of high RF interference revealed by frequent or prolonged lighting of the LED in the receiver after it is operational random flicker is OK Installing the Lock if used Use an Ademco No N6277 Cam Lock and No N6277 1 Push On Clip Retainer Clip Note The cabinet can be closed and secured without a lock by using 2 screws in the cover s edge 1 Remove the cabinet door It is po ore Postal easily removable for servicing and is easily re installed 2 Remove the lock knockout from the control cabinet door RETAINER Insert the key into the lock SE Position the lock in the hole making certain that the latch will make contact with the N UNLOCKED latch bracket when the door is closed 3 Hold the lock steady and insert the retainer clip into the retainer slots Position the clip as illustrated in order to Figure 1 Installing The Cabinet Lock permit easy removal CABINET DOOR BOTTOM Before installing the cabinet s contents remove the metal cabinet knock outs required for wiring entry Do not attempt to remove the knockouts after the circuit board has been installed 10 Mounting The Control s Circuit Board Alone in The Cabinet Fig 2 1 2 3 Hang two short Black mounting clips provided on the raised cabinet tabs see Detail B in Fig 2 Insert the top of the circuit board into the slots at the top of the cabinet M
108. ers Table Also refer to APPENDIX A near end of this manual for transmitter input loops button locations Model Description Input Type And Special Notes 5801 Wireless Panic e Unit has 4 pushbuttons each with a unique Input loop code Transmitter e Each pushbutton must be assigned to a zone Enroll as 3 for RF supervised or 4 for UR unsupervised Note Input loop button No 4 must always be used 5802 Pendant Belt Clip Enroll as 5 for BR button type transmitter 5802CP Personal Emergency Transmitters 5802MN Miniature Personal Enroll as 3 for RF supervised or 4 for UR unsupervised Emergency Trans 5804 Wireless Key e Has 4 pushbuttons each with a unique input loop code Transmitter e Each pushbutton must be assigned to a zone Enroll as 5 for BR button type transmitter Note All buttons must be assigned the same Input Type 5806 Wireless Enroll as 3 for RF supervised 5807 Photoelectric At the INPUT S N prompt fault the detector as follows 5808 a On many detectors press the special test switch not test button provided for faulting the detector see detector s instructions then release Note With some detectors two contacts must be shorted to fault the detector Disengage detector s cover and swing cover open these contacts are on the PC board near a blue jumper see detector s instructions Momentarily short these contac
109. etwork the telephone company may request you remove the equipment from the network until the problem is resolved There are no user serviceable components in this product and all necessary repairs must be made by the manufacturer Other repair methods may invalidate the FCC registration on this product This equipment cannot be used on telephone company provided coin service Connection to Party Line Service is subject to state tariffs This equipment is hearing aid compatible When programming or making test calls to an emergency number briefly explain to the dispatcher the reason for the call Perform such activities in the off peak hours such as early morning or late evening 88 Section 26 SPECIFICATIONS ACCESSORIES Specifications FA162C 1 Physical 12 1 2 W x 14 1 2 H x 3 D 818mm x 368mm x 76mm SECURITY 2 Electrical CONTROL VOLTAGE INPUT 16 5VAC from plug in 25VA transformer Ademco No 1321 in U S A RECHARGEABLE BACK UP BATTERY 12VDC 4AH Gel type Charging Voltage 13 8VDC ALARM SOUNDER 12V 2 0 Amp output can drive 12V BELLS or can drive one or two 702 series connected self contained 20 watt sirens Do not connect two 702s in parallel AUXILIARY POWER OUTPUT 12VDC 600mA max Interrupts for 4 wire smoke detector reset Note For UL installations Alarm Sounder plus Auxiliary Power currents should not exceed 700mA total STANDBY TIME see Table in POWERING THE SYSTEM section FUSE
110. f 6 is pressed system ready for next word 10 The two words in our example have now been entered Note however that up to three words may be entered provided the number of characters will fit on the screen Press 8 to save all words in memory Summary Display The flashing cursor will disappear indicating that the word s are stored ZN 01 BACK in memory for that zone as shown in DOOR the summary display at the left 11 To enter a descriptor for the next zone press plus the desired zone number e g 02 The summary display following step 4 previously will appear Now repeat steps 6 through 10 for the descriptor for the next zone 12 To exit the Alpha descriptor mode press 0 0 at the summary display Program Alpha This prompt will be displayed 0 No 1 Yes 00 Alpha Pgm 13 Press 0 This will be displayed 82 14 Press 99 to exit the programming mode 68 Adding Custom Words will not be annunciated by FA4285 Phone Module You can add up to 10 installer defined words to the built in vocabulary Each of the 10 words can actually consist of a word string of one or more words but no more than ten characters can be used for each word or word string When adding Custom Words the keypad keys perform the following functions 4 Moves cursor one space to the left 6 Moves cursor one space to the right 8 Saves the new word in the system s mem
111. f the Security System should be carefully tested as follows 1 Connect the battery wires from the control board to the battery observing correct polarity Enter the installer code 4112 and press the TEST 5 key on the keypad The external sounder should sound for 1 second if the sounder is good and proper connections have been made Note that if the backup battery is discharged the sounder will not turn on To turn off the test mode enter the installer code 4112 and press the OFF key Disconnect the battery wires from the battery terminals Unplug the AC transformer from the AC outlet 37 Section 10 LONG RANGE RADIO General Information Check availability of Models 7720 PLUS or 7820 long range radios If output to long range radio is selected all messages that are programmed to go to the primary telephone line receiver will also be sent to the 7720 PLUS or 7820 long range radio These messages will be in Contact ID format not affected by entry in field 48 U L For UL installations Long Range Radio must be disabled 29 0 The data line is supervised as well as certain functions in the radio If communication is lost or a trouble develops a message will be attempted to be sent via both radio and telephone to the central station For complete information see the manual that accompanies the radio Connection Connect the data in data out terminals and voltage input terminals of the No
112. feet from the receiver s antennas The 5800TM must not be installed within the control cabinet Mount the unit using its accompanying mounting bracket 5800TM Wiring Connections Connect the 5800TM to the control panel s keypad connection terminals using the supplied connector with flying leads as follows Wire Terminal On Control BLACK Ground Terminal 4 RED 12VDC Terminal 5 GREEN Data to Control Terminal 6 YELLOW Data from Control Terminal 7 BLUE Not Used Do not cut any of the jumpers on the 5800 TM when using it with the FA162C For additional information refer to the 5800TM s instructions 5800 Series Transmitters General 5800 series transmitters have built in serial numbers that must be enrolled into the system using the 56 or 83 interactive mode or input to the control via the downloader 5800 series transmitters except 5827 described separately do not have DIP switches Each transmitter s zone number is programmed into the system in 56 mode Some transmitters such as the 5816 and 5817 can support more than one zone referred to as loops or inputs On the 5816 for example the wire connection terminal block is loop 1 the reed contact is loop 2 Each loop must be assigned a different zone number U L The 5816 and 5817 transmitters do not have EOL supervision of their loop wiring Therefore for UL Household Burglary installations the loop wiring may not exceed 3 feet For
113. g Powerline Carrier devices you must use a 4300 transformer instead of the 1321 transformer The 4300 transformer provides AC power to the control panel and also supplies signals from the control panel through the premises AC wiring to the Powerline Carrier devices which are plugged into AC outlets Devices plugged into Powerline Carrier devices can then be made to perform various functions in response to commands entered at the keypads in the security system 30 Wiring Connections 1 Splice one end of a 3 conductor cable to the wire ends of the 4142TR cable supplied with the 4300 transformer 2 Connect the 4142TR cable plug to the 9 pin connector on the control see SUMMARY OF CONNECTIONS diagram for location of the 9 pin connector 3 Connect the other end of the 3 conductor cable to the 4300 transformer as indicated in the table below and in the diagram that follows 4300 TRANSFORMER WIRE CONNECTIONS 4300 TRANSFORMER INTERFACE 9 PIN CONNECTOR ON CONTROL BOARD Earth AC Ground AC Sync Data Com YELLOW SC y 4142TR CABLE THESE WIRES 7 8 9 NOT USED 1 2 TERMINALS ON CONTROL BOARD Figure 15 4300 Transformer Wiring Connections Programming Relay Outputs In this system each device must be programmed as to how to act ACTION when to activate START and when to deactivate STOP Refer to the programming procedures for 80 and 81 interactive modes that a
114. g the 5800 TM Module 25 Mounting the 5800 TM Module occconoccccnonoccnonononnno Ge RA AR AA RA ee RA Ge ee ee ee ee 25 5800TM Wiring Connections ees ees se ee Re AA AR ee AR Re a AR AR Re ee ER nn ee ER ee ee 25 5800 Series Transmitters sesse ss ses se AA Ge ee RA de AA ee AR Gee AA ee ee RA AA ds 25 General EE EE Oe Ee ee ec tue ED DE NE EE GE ee 25 Transmitter SupervisioN ees sees ee ER Ke AA Re AA Re AA Re AA GR Ee Re ee ee ee ee R AK Ge 25 Transmitter Input TYPES sissies seeks eb Ng Webb Ee EEN de Gesag ERENS Re eb GR KEES Ee bk ee ER 26 Transmitter Battery Life iis ees se ee rii ee AR ee AR ee AR Re ee Ee ee AR ee AR ee AR ee ee 26 Using the Transmitter Sniffer Mode coooooccononoccccnononnnono GE RA Re AA Re AA Re GR ee Ge ee 26 5800 Series Transmitters Table 27 Section 7 RELAY OUTPUTS POWERLINE CARRIER DEVICES cocos 29 Relay Powerline Carrier Device Basics oooooccconoccncnonocanonono ee Se AA GE RA ee AA ee AA ee ee 29 Nos 4204 And 4229 Output Relay Modules sees se ee se Gee SR RA AR ee ee ee sees 29 4204 4229 SEP RE A A A AAA 29 Powerline Carrier Devices oooonconnncccnonccnonnconnn Ge a o de Ad Ge nc nano eesuecesueceeaaeceaeeceeneeesaes 80 Wiring Connect E OE Oe ee 31 Section 8 Section 9 Section 10 Section 11 Section 12 Section 13 Section 14 Section 15 Section 16 Section 17 Section 18 Section 19 Section 20 Section 21 Section 22
115. he alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path A user may not be able to reach a panic or emergency button quickly enough While smoke detectors have played a key role in reducing residential fire deaths in the United States they may not activate or provide early warning for a variety of reasons in as many as 35 of all fires according to data published by the Federal Emergency Management Agency Some of the reasons smoke detectors used in conjunction with this System may not work are as follows Smoke detectors may have been improperly installed and positioned Smoke detectors may not sense fires that start where smoke cannot reach the detectors such as in chimneys in walls or roofs or on the other side of closed doors Smoke detectors also may not sense a fire on another level of a residence or building A second floor detector for example may not sense a first floor or basement fire Finally smoke detectors have sensing limitations No smoke detector can sense every kind of fire every time In general detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical circuits children playing with matches or arson Depending on the nature of the fire and or location of the smoke detectors the detector even
116. herefore be carried off premises BR Unsupervised Button RF Type only send fault signals They do not send low battery restore or check in signals The transmitter may be carried off premises INPUT LOOP 3 4 ALWAYS U 5801 LEARN AS UR OR RF 5802MN LEARN AS UR OR RF YOU MUST LEARN THIS BUTTON LOOP 4 5804 LEARN AS BR LEARN AS RF 5802 5802CP LEARN AS BR INPUT LOOP 2 3 2 A 1 5817 LEARN AS RF 5803 LEARN AS BR INPUT LOOP 1 TERMINALS PEA a en is 5819 LOOP 3 LEARNAS RF INPUT TERMINALS e LOOP 1 5806 5807 5808 5806 SHOWN NEUE LEARN AS RF LOOP 1 MOTION 5849 LEARN AS RF 92 INPUT INPUT LOOP LOOP 2 2 REED REED LOOP 1 INPUT TERMINALS LOOP 1 SE 5816 LOOP 1 VK TERMINALS ALTERNATE SSMN POSITION LEARN AS RF FOR LOOP2 O INPUT LOOP 1 5818 LEARN AS RF 5827 SET HOUSE CODE 5827BD SET HOUSE CODE NS INPUT LOOP 1 MOTION 5890 LEARN AS RF INDEX T minute delay aria ici 41 A EE EG RE EE ER Ge oes 7 14 15 90 TOLLBEL2M OR EE OR EE HR 36 CU EE EE HER N 7 9 14 15 43 90 T EE MO HEES ER GE 8 9 12 30 41 GIRRES eebe SE irc 15 A EE DE EE EG GE ee ee 91 URE ER EI ad EE EE 91 Pi AE AE OE Ed 91 He Reeg ee 91 TASIE ESE T DE Ee EE Ge IA 91 HARE E EER EE 91 1451DH EE EE EE EE RE eg 91 TAD EE 91 15 SECOND DIALER DELAY BURGLARY
117. icable Are Indicated In Text The following pages list all data fields in this control in numerical order If you have performed the programming instructions that were included with the installation of each of the various peripheral devices covered in previous sections this table will simply serve as a reference for all data fields in the system If you have decided to program all the data fields in the system at one time and therefore did not perform the programming indicated previously in each section you can use this listing to program all the data fields now 20 INSTALLER CODE 4111112 The Installer code is used to enter the 4 digit Master security code for each partition in the normal operation mode via the keypad connected to Partition 1 See Master Code in the SYSTEM OPERATION section for procedure Enter 4 digits 0 9 21 QUICK ARM ENABLE Partition1 0 Partition 2 0 0 do not allow quick arm 1 allow quick arm the key can be used instead of the security code when arming the system 22 RF SYSTEM 0 0 no RF receiver being used 1 5881 5882 RF receiver being used 23 FORCED BYPASS FUNCTION Partition 1 0 Partition 2 0 0 no forced bypass 1 provide automatic bypass of all open faulted zones 2 provide automatic bypass of all open zones and zones 17 30 and 31 whichever are in the system This feature allows all faulted zones to be automatically bypassed with a single command All zones bypassed
118. if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual Passive Infrared Detectors do not provide volumetric area protection They do create multiple beams of protection and intrusion can only be detected in unobstructed areas covered by those beams They cannot detect motion or intrusion that takes place behind walls ceilings floors closed doors glass partitions glass doors or windows Mechanical tampering masking painting or spraying of any material on the mirrors windows or any part of the optical system can reduce their detection ability Passive Infrared Detectors sense changes in temperature however as the ambient temperature of the protected area approaches the temperature range of 90 to 105 F 320 to 40 C the detection performance can decrease Alarm warning devices such as sirens bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors If warning devices are located on a different level of the residence from the bedrooms then they are less likely to waken or alert people inside the bedrooms Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo radio air conditioner or other appliance or by passing traffic Finally
119. l operation mode is used to enter the Master code for each partition which allows access to the normal functions of the system In normal operation mode the Installer code is used to enter the 4 digit Master security code for each partition using the keypad connected to Partition 1 To enter the Master code for Partition 1 enter Installer Code 8 01 desired 4 digit Master code for Partition 1 To enter the Master code for Partition 2 enter Installer Code 8 02 desired 4 digit Master code for Partition 2 To change the Master code enter Current Master code 8 02 new Master code new Master code again Secondary User Codes Notes In normal operation mode each partition s Master security code can be used to assign up to 12 secondary 4 digit security codes plus a babysitter code and a duress code for that partition The master code can also be used to remove secondary codes from the system individually To assign or change a Secondary security code enter via partition s keypad Partition s Master Code CODE key User 03 16 desired Secondary Code The system will emit a single beep when each secondary code has been successfully entered To delete a Secondary security code enter via partition s keypad Partition s Master Code CODE key User 03 16 e All Master and Secondary security codes permit access to the system fo
120. mains faulted when exit delay expires After entering 81 the following prompts are displayed Enter the Zone List Number 01 02 03 or 04 to program or 00 to end these entries Press the key to advance In the following displays zone list 01 has been selected for programming Enter each zone number to add to the zone list by first entering the zone number then the key example 01 02 03 After all zones desired are entered press 00 to advance IMPORTANT Do not include fire zones in zone lists that are used to STOP relay actions To delete the zone list enter 1 Yes All zones in the zone list will be deleted automatically and programming will return to the first screen To save the zone list enter 0 No to advance To save the entire zone list enter 0 No and programming will return to the first screen To delete a zone or zones in a zone list enter 1 Yes to advance Enter each zone to be deleted from the list followed by the key After all zones to be deleted are entered enter 00 to return to the first screen so that another list can be programmed if desired NOTES e Any list may include any or all of the system s zone numbers e A zone list can be assigned to more than one output relay 65 Section 19 ALPHA DESCRIPTOR PROGRAMMING This section provides instructions for programming alpha zone descriptors This is recommended for systems using Alpha keypads and necessary ifa
121. ment Required At the premises 3 FA162C and keypad At the installer s office home 3 An IBM PC compatible computer 3 Hither a HAYES brand SMARTMODEM 1200 Level 1 2 or higher external or Level 1 1 or higher with 4 position DIP switch internal stylel or a HAYES brand Optima 24 Plus FAX96 Modem 3 FADL Downloading Software Diskette at revision level supporting the FA162C Y Appropriate interconnecting cables Initial Download Enter Installer code 5 This sets field 95 to 4 rings and system to no call back option The download computer can then call the subscriber make connection and download all programming items 74 Remote Programming Information Notes The downloading system can perform many functions when in communication with the control unit Besides uploading and downloading the status of the system can be observed and various commands can be initiated as follows Y Arm the System in the Away Mode Disarm the System Bypass a Zone Force the System to Accept a New Program Download Shut Down Communication dialer Functions non payment of monitoring fees in an owned system Shut Down all Security System Functions non payment for a leased system Inhibit Local Keypad Programming prevents account takeover Command the System to Upload a Copy of its Resident Program to the office Read Arming Status AC Power Status Lists of Faulted Zones Bypassed Zones Zones Currently in Ala
122. mming form This is an interactive menu mode that is used to program zone numbers zone types partition numbers alarm and report codes and to identify the type of loop input device This mode can also be used for enrolling 5800 series transmitter ID codes and for entering Alpha descriptors for zones we recommend entering descriptors in menu mode 82 NOTE If using wireless transmitters there are two methods for enrolling the transmitter serial numbers The first method is by using 56 Zone Programming mode described below The second method is by using 83 Sequential mode Note that the 83 Sequential mode requires that all zone information first be entered using 56 Zone Programming mode Program Tool The Zone Programming and Sequential Modes allow you to use a 5803 or 5804 button type transmitter as a program tool The upper left hand and right hand buttons of the tool duplicate the and keypad programming functions The advantage of using a program tool is that it enables remote enrollment You can move to the physical location of the transmitter to be enrolled press the upper left hand button of the program tool and then trip the intended transmitter The transmitter that you use as the program tool can also be used as a transmitter in the system If you plan to use an existing transmitter it must first be enrolled into the system as its associated zones You may then program it as the tool After
123. n 1 or 2 e Relay and Powerline Carrier device outputs assignable to either partition 1 or 2 or to both partitions e Certain system options such as Entry Exit delay and Subscriber Account number programmed independently for each partition Common Zone e Common Zone option allows either partition to arm while leaving a common area ex lobby or foyer disarmed for access into the other partition Refer to the ZONE LISTS section for details on programming a common zone U L In UL installations the system may be configured as a single partition only Remote Keypads Up to 4 of any of the following keypads may be used in each partition Fixed Word Keypads FA210KP and FA250KP These keypads cannot be used if the FA4285 Phone Module is being used Alpha Keypads FA550KP 2 line alphanumeric displays FA450KP 1 line alphanumeric display A For programming from a keypad a FA550KP 2 line Alpha keypad must be connected to partition 1 but need not stay in the system 7 Security Codes One installer code for entire system user 1 One Master code for each partition user 2 12 secondary user codes for each partition users 3 14 One baby sitter code for each partition user 15 One duress code for each partition user 16 Baby sitter Code A special code that can only be used to disarm the system KL if that particular code was used to arm it Duress Code An emergency code which when entered by any use
124. n protection for that given point within the system e Some transmitters e g 5802 5802CP and 5803 contain long life but non replaceable batteries and no battery installation is required At the end of their life the complete unit must be replaced and a new serial number enrolled by the control e Button type transmitters ex 5801 5802 5802CP amp 5803 should be periodically tested for battery life e The 5802MN and 5804 button transmitters have replaceable batteries Using The Transmitter Sniffer Mode 1 Enter Installer code 4112 3 from partition 1 s keypad This initiates a procedure that will provide a check that all transmitters have been properly programmed 2 The keypad will display all zone numbers of wireless units programmed into the system Fault each transmitter in turn causing each one to send a signal rather than let each transmitter send an automatic supervisory signal As the system receives a signal from each of the transmitters the zone number of that transmitter will disappear from the display The transmitters may be checked upon installation or in an installed system 3 When all transmitters have been checked exit the sniffer mode by keying Installer code 4112 OFF NOTE Sniffer mode does not automatically expire You must manually exit installer code OFF sniffer mode to return to normal operation Sniffer Mode also terminates if a user arms the system 26 5800 Series Transmitt
125. ndows not properly aligned Control has sensed a high resistance condition on a loop in one of the hard wired zones 2 8 85 SYMPTOM POSSIBLE CAUSE REMEDY L Transmitter signal not Check or change transmitter s battery Check FA162C s AC power Check code switches inside transmitter Must match with RF House Code programmed in FA162C Move transmitter or RF receiver Check for large metal obstructions then relocate transmitter if necessary Verify by activating 5881 5882 with another similar transmitter If O K now return defective transmitter Verify by making sure other transmitters cannot activate 5881 5882 If defective replace and return original 5881 5882 Verify programming Set DIP switch on 5881 5882 for address 0 Set field 22 for 1 Set ZT to a valid active zone type in field 56 Install proper battery Enroll unit in field 56 or 83 System battery is low or missing Remote RF keypad battery is low Transmitter for zone nn has a low battery Enter Code OFF to exit TEST mode Enter Code OFF and replace the battery Check the transmitter indicated Restore communication to the receiver to cancel the condition Delete input s serial number not the zone and enroll the proper input see field 56 Determine which transmitter is programmed for this zone and reprogram as necessary Check installation to see ifin accordance with established proc
126. nds a report to Central Station and provides an alarm sound at the keypad No bell output is provided This zone type is usually assigned to a zone containing a button for use in personal emergencies or to a zone containing monitoring devices such as water or temperature sensors etc This zone type provides a fire alarm on short circuit and a trouble condition on open circuit The bell output will pulse when this zone type is alarmed This zone type is always active and cannot be bypassed This zone type can be assigned to a control panel basic wired zone any zone in a wired zone expansion module or wireless zones When used with zone 1 on the panel 2 wire smoke detectors can be used For an explanation of the verification function refer to the Operation paragraph in a previous section titled 2 Wire Smoke Detector Installation Note Only hardwired zone 1 can be programmed as a fire zone in UL installations However any wireless zone can be used as a fire zone This zone type gives entry delay 1 using the programmed entry time if tripped when the panel is armed in the Away mode Entry delay begins whenever sensors in this zone are violated regardless of whether or not an entry exit delay zone was tripped first No entry delay is provided if tripped when the panel is armed in the Maximum mode Exit delay is present for any arming mode This zone type is bypassed when the panel is armed in the Stay or Instant modes This i
127. ne 10 Press to continue The system will starting with this zone number search for the first transmitter which has all of the following attributes pre programmed in Zone Programming a An input type of RF UR or BR programmed b A loop number programmed c No serial number programmed Zone Number Entered If the first zone number entered does not have one or more of the above attributes the system will search its database for the first zone that does and will display it on the next screen 71 10 INPUT S N L 5 This prompt is displayed when the system has found the next zone i which needs to be enrolled The system will respond to the first serial AXXX XXXX number transmitted after the key on the keypad is pressed A serial number may be enrolled by one of two methods a Enter the 7 digit serial number printed on the transmitter or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc 2K If you do not wish to enroll the zone displayed press the key on the keypad or the upper right hand button on the program tool a long beep will be heard to verify The following prompt will appear 10 LEARN S N 0 NO 1 YES 0 To enroll now enter 1 YES If 0 NO is entered the following prompt will appear if a program tool has already been programmed Zone Number Entered Enter the next
128. nnoncncnnnnos 51 Supervised Fire tidad dcir Ee 46 Supplementary Power Supply esse Re Re 15 System Communication esse sees RA RA ER 76 System Operation esse Re RA RA Re Re 63 System Sensor PAAOOB eee ees ee ee Re 36 System Status And Restore Report Codes o 52 System Status Report Codes sesse Re 53 Tamper Protection iss sees AA RA 21 25 Technical Support sees ees RA RA Re Re 87 Tele lime mas 34 Telephone Line Monitoring sesse sesse ese 9 Test Mode saint tetra ee dee e 83 84 Test Report Code conoocccnocccoooccnoonnncnoncncnoncncnnnnncnoncnnnnnnnnnns 53 Test Report Offset serren neesii i a i rE n as 52 Test Restore Report Code 54 Touch TS 32 TouchTone Phone 35 Transmitter Input Types ccooooccccnononocononononononononannnanons 26 Transmitter Sniffer Mode sees esse see ee 26 83 85 Transmitter Supervision sesse esse Re Re RA 25 Trouble by Day ese EE OR Ee EE See Re SE Ee EE 45 Trouble Condition esse sesse ee ee AA RA AA 82 95 Trouble Report Code iese RA RA RA 53 Trouble Restore Report Code esse ese RR 54 UD iaa iia 13 15 25 36 38 42 88 89 Unsupervised RE A 25 Vocabulary List tin iia 70 Wired Zone Expansion iese sesse esse ee ee 7 43 44 47 Wireless Expansion esse esse esse ese ee ee ee ee ee ee 7 Wireless Transmitter esse ese esse ee ee ee RA ei 71 Wireless Transmitters ooooconnccnoccnocnconnconnconncnnnacanononnc
129. nnos 23 Wireless Zones esse ee ee RA AR AA ee ee 23 Wiring 2 Wire Smoke Detector eise sesse see ee 17 Wiring 4 Wire Smoke Combustion Detectors 18 Wiring Length Gauge Chart esse ese esse ee ee Ee 14 Word String eege See Seg gaas dr Ge Gees eee ER Ae 69 Worksheet Ee Se EE ida 42 XAO ER eats 64 Zone Descriptors issie EER GEDOSEER ee DS Res BED ae 9 Zone Descriptors es ee AA RA ee 70 Zone EXPANSlON se ese eek sess ee pie ge se 21 LOMO VASE es EE EES EE geag 44 LOVE Not Used RE EE in ie E E 45 Zone Programming sesse esse ee see ee ee de ee ee 44 Zone Type Default iese ee RA e Re 58 Zone EE 45 63 NOTES NOTES 07 WARNING THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced design security system it does not offer guaranteed protection against burglary fire or other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example e Intrusion detectors e g passive infrared detectors smoke detectors and many other sensing devices will not work without power Battery operated devices will not work without batteries with dead batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly Signals sent by wireless transmitters may be blocked or reflected by metal before they reach t
130. nt the triggering of a 24 hour zone to occur enter 1 or 2 or enter 0 for any partition e To stop the Device action and turn off the lamp we do not want to use a restore of any zone so a 0 will be programmed for the Restore of Zone List ZL We will use a manual entry of User Code 8 Device to turn off Therefore we do not need to program a STOP event Press to continue e The system will display a summary screen for the START programming for device 01 Press to continue e The system will display a summary screen for the STOP programming for device 01 Press to continue e The system will display the X10 prompt Enter 1 for yes e The Enter Device No prompt for the next zone will be displayed e Press 00 and then to exit the 80 mode Now use 81 Zone List mode to program the 3 specific zones in Zone List 1 64 Section 18 ZONE LISTS 81 Menu Mode Defining A Common Zone Zone List Displays Zone List No 00 Quit 01 01 Enter Zn Num 00 Quit 00 01 Del Zn List O No 1 Yes 0 01 Delete Zone O No 1 Yes 0 01 Zn to Delete 00 Quit 00 While in program mode press 81 to enter Zone List Menu Mode This mode is used to program zone lists for output devices programmed in 80 menu mode and or for defining a common zone Refer to the Programming Form worksheet for 81 Mode A common zone allows either partition to arm the system while leaving the design
131. nual for examples of pager displays 15 SECOND DIALER DELAY BURGLARY o 0 no dialer delay 1 provide 15 second delay of burglary alarm report except zone type 24 to the central station which allows time for the subscriber to avoid a false alarm transmission This delay does not apply to zone type 24 alarms which are always sent as soon as they occur UL installations must be 0 no delay PERIODIC TEST REPORT 0 0 no test report 1 once every 24 hours 2 weekly 3 once every 30 days Test Report Code entered in field 64 is sent Reports with Partition 1 Subscriber No BAD TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES 59 76 amp 89 52 TEST REPORT OFFSET 2 0 24 hours after exiting program mode or download 1 6 hours after exiting program mode or download 2 12 hours after exiting program mode or download 3 18 hours after exiting program mode or download This is the time to first report from programming or downloading 53 SESCOA RADIONICS SELECT 0 0 Radionics 0 9 B F reporting 1 SESCOA 0 9 only reporting Select 0 for all other formats Report codes can be programmed using the interactive 56 Zone Programming Mode or codes can be entered in data fields 59 76 89 The following is a set of guidelines to be used for programming report codes The actual report code digits that you enter depend upon the particular installation an
132. o EE EA OE Ee 25 71 Auxiliary Output seise ricis ii 42 Ch EE 25 27 85 Auxiliary Power Output ooooocccnoocccnocncooncnononnnnonnncnoncncnnnnnos 9 RE EE EO 27 IA A OE ER AN E 23 25 28 Baby sitter Code iese E Es ek Ee cinco GEE ee EE ee 8 LI EES EE e 85 Back Up Battery iese esse ese ee 9 13 37 41 BO TBD EE 23 25 90 Basic Hardwired Zones cccccssssccceeeessseeecessssseeeeeeseaes 7 BOAO diana 27 Battery Connector Cable esse Re Re 42 5881 5882 in Canada eocooccccnoonccnoncnnoonnncnonnnnnnonnnnnnnnnnnnnoss 7 Battery Life icono Gilead 26 te AD ER NE NE OE EE OOR 23 Battery SIZE tre EES ES kes eg ge deed Se DAE Dee eend Ee 41 5881 5882 SERIES cooooooccnocccononnnnonnncnnnnncnonnnonononcnanoncnnos 90 Battery Standby Formula 42 A ee ege EE ege Ge 85 Bellis aiii eds 37 BOSD MEE NI EE EL HER ER ES 7 23 Button Transmitters ccccccnnnnnnnnnononononononnnnnnnnononononnnnonos 25 5881H 5882H in Canada e ccmoocccnoocnononncooncnononnnnnnnnonnnos 23 Button Type Transmitters ococoocccnnocnnoooncnionancnnncncnnnno 71 A ET EE EE EE N ON 7 Bypass Report Code iese Re RA Re RA 53 BSB1D ose EE N EE OO ER EEN 23 Bypass Restore Report Code esse esse ee 54 DOOL ME Ui ER ee GE EG seat ee Maes eed Set 7 23 Bypassing Zones enient er arer a EE S 80 TEEN 27 EE ee eebe Seele 7 14 90 A GE ER tea tev tee EE ED 14 15 90 APE AE NE EE AE OE EE 7 GLEN ER ege is 7 14 15 90 93 Cabinet Dock 02 0228 ccc
133. o caidas 29 Relay Programming ooocccooooncnoonnnnooncnnnoncnonnnnnonnonononannnos 44 IEN 29 Remote Keypads sroine etenei 7 Remote Programming i esse sesse ee ese ede ee ee 74 ES deu RR OE N EE 53 58 Report Code Formats esse sesse ese RA Re Re 76 report COMES escht de See SR de Eed GR GR Eg Se BEE KERE EE EE 52 Report Format je ses Es Se ese dd ee od ere dt Zeie 50 Response Me sis e SEKS EN EER Gee theater tee ego 58 ER OE EE EEA 54 RE House ID sei ss ERG NEE SG on Ge ne eg Ge S 25 RE House lD Code ass ses ees es ve ii 47 RF interference A edd ie Seed Ges 23 RE Keys miii EE EE EE EN 25 RE Receiver i s es ai dd aa 23 RE System naci dio aio 43 44 47 RF Xmtr Low Battery Report Code esse esse ese 54 RF Xmtr Low Battery Restore Code oooccooccccnoccccncncnoos 54 Ring Detection Count For Downloading 56 IERT 12 33 34 Secondary Phone NO cocooccnoocccoooncconnncoonncnononcnnnncnononcnnnoss 50 Secondary Subs Account NO esse RA Re 50 Secondary User Codes iese RR Re 79 Security Codes EE SEEK taa 79 Sequential mode Re EA RA 44 71 Serial Number mehteran s 71 85 Sescoa Radionics ie SE ER Ee WE GR TT 9 Sescoa Radionics Select se ee 52 Silent si EG EE RS EE ENEE 46 Silent Palin ler rote 81 Single Alarm Sounding Per Zone esse ss see ee 48 SITeTS EE RN 87 Smartmodem 1200 ees ee 74 Sotinders e Seene ee eege eendeiteg 91 Split Dual Reporting oooocnnocccnoncncnoncncnoncncnonnn
134. one Module 40 Figure 22 FA162C Summary of Connection sesse sesse ees Inside Back Cover CONVENTIONS USED IN THIS MANUAL MAIN SECTION TITLES ARE SHOWN IN REVERSE TYPE Before you begin using this manual it is important that you understand the meaning of the following symbols icons UL These notes include specific information which must be followed if you are installing this system for a UL Listed application continuing with the installation and which if not observed could result in A These notes include information that you should be aware of before operational difficulties of the system or could cause damage to the system Please read each warning carefully This symbol also denotes warnings about physical harm to the installer A This symbol indicates a critical note that could seriously affect the operation 20 INSTALLER CODE In the text of this manual basic programming data fields are indicated by a star followed by the data field number and its title Enter Zn Num 00 Quit 01 In the text of this manual interactive programming prompts are shown in a double line box e g Menu Mode 56 for Zone Programming PRODUCT MODEL NUMBERS Unless noted otherwise references to specific model numbers represent Ademco products Section 1 GENERAL DESCRIPTION The FA162C is a 2 partition control that supports up to 38 zones using basic hard wired wir
135. ory 1 Perform steps 1 2 and 3 of Programming the Descriptors on a previous page Select CUSTOM WORD mode enter 1 when the prompt CUSTOM WORD is displayed Enter the number 01 10 of the custom word or word string to be created for example if you are creating the first custom word or word string enter 01 for the second enter 02 etc A cursor will now appear at the beginning of the second line Refer to the CHARACTER LIST of letters numbers and symbols on a following page Press the key followed by the two digit entry for the first letter you would like to display e g 6 5 for A The cursor will then move to the right in position for the next character Repeat step 3 to create the desired word s Note that the 4 key can be used to move the cursor to the left if necessary Remember no word or word string can exceed 10 characters Press the 8 key to save the custom word s and return to the CUSTOM WORD display Repeat steps 2 5 for other custom words to be entered To change a custom word just overwrite it If no more are to be entered now press 0 to return to the Descriptor entry The custom word s will be automatically added to the built in vocabulary When zone descriptors are being entered as described in step 6 of Programming the Descriptors the custom word numbers are 245 to 254 for words 1 to 10 respectively 69 ALPHA VOCABULARY LIST For Entering
136. ound ivi ias 13 41 Entering Program Mode 43 Entry Delay EE ER OR EE EE EN 1 85 Entry Exit Burglary sesse sesse ek ee ee ee RA Re ee 1 2 EOL Resistor esse sesse ee se ee 16 17 18 20 21 2 EOL Supervision 25 Event Log 80 Full Report Code 54 Event L gging issie es Vee Deeds Ee Ge DE ss Ee ee eg se ee S EES 9 55 Exit Delay carnada OE cis 85 Exit Error Alarm id eer ese N ee Nee ta 81 Exit Error Report Code A 58 Expanded or 442 Format sesse esse esse ee ee ee ee ee 52 Factory Defaults literas 44 FADL Downloading Software esse esse ese 74 75 REEL eege O ee 88 Fire alarm sounding ooocooocccnocccononncoonnnnnnnnnnonnncnoncncnnnnnnno 18 Fire Sounder Timeout esse esse ee RR 48 Fixed Word Keypads cooooocconoccnononncnonnnnnonnncnonnncnononcnanoncnnns 7 Forced Quick Bypass coooocccnooccnooocnnnoonnncnonnnos 43 47 80 tee EE 76 OE eds EE OE EA EE 89 Go No Go Test Mode eie ee ese Re Re 28 84 Handshake EE EE bic 76 Hard Wired Zones esse esse ee Re Re Re Re 17 HAYES modem specified by Ademco 9 HAYES Modem EE 74 House ID NEE 23 28 House Identification oooonococnnocncononcnoncnononnncnnn conan cnnnnns 23 IBM Compatible Personal Computer PC 0 0 74 IBM Personal Computer esse esse se Re RA 43 Ideal Model 61 035 coooooccnnocccconocnnoonnnnnnonnncnonnnccnnnnoos 13 41 TEI 735L series detectors ees ese RA RA Re 19 Input Device types AEN 58 Installer Code EE 43 47 In
137. pervision in the control senses high resistance on hard wired zone loops 2 8 causing a warning CHECK display with the affected zone number to occur when the system is in the disarmed state The system cannot be armed when this display is present If the system is in the armed state when the high resistance condition occurs no display will take place until the system is disarmed Wiring 2 Wire Smoke Detectors To Zone 1 1 Connect 2 wire smoke detectors across zone 1 terminals 8 and 9 Observe proper polarity when connecting the detectors 2 Ifan EOL resistor is presently connected across zone 1 terminals remove it The EOL resistor must be connected across the loop wires at the last detector U L In UL installations only zone 1 may be used as a Fire zone In addition an Ademco Model 610 7 must be used as an End of Line resistor at the last detector in the alarmed state A The alarm current provided by zone 1 will support only one smoke detector Verify Operation of The control panel will verify any alarm by resetting the smoke detectors 2 Wire Smoke Detectors after the first alarm trigger and then waiting 90 seconds for a second alarm in Zone 1 trigger If the smoke detector or thermostat does not trigger again the control will disregard the first trigger and no alarm signal will occur This feature eliminates false alarms due to electrical or physical transients
138. port Code RC The report code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0113 for 3 and 1 2 for C Enter the numbers and press to continue Input Device In For the 8 built in hardwired zones the Input Device types are automatically displayed as HW Panic Duress and Tamper inputs are not applicable For the auxiliary wired zones or RF transmitters enter the input device type as follows 2 AW auxiliary wired zone 3 RF supervised RF transmitter 4 UR unsupervised RF transmitter 5 BR button type RF transmitter unsupervised Refer to the 5800 Series Transmitters Table in the WIRELESS EXPANSION section for the specific procedure required to enroll a particular transmitter Press to continue 58 3 Loop number LP Enter the loop number 1 4 for the zone of the 10 INPUT DEV LP transmitter being enrolled The default is loop 1 To accept this RF TRANS RF 1 press If a different loop number is being used on this transmitter enter the desired loop number and press to continue see the transmitter s Installation Instructions for specific loop designations The loop number must be entered here whether using Zone Programming or Sequential Mode to enroll transmitters 10 LEARN S N If the transmitter s serial number has not been previously enrolled you may enter the enroll mo
139. r arming disarming etc e The installer code can disarm the system only if it was used to arm it e Babysitter code is User code No 15 i e it can disarm the system only if it was used to arm it e Duress code is User code No 16 When this is used to perform any system operation a special code is sent to the monitoring station Instruct users to be careful not to use this code for normal usage e Ifa secondary code is inadvertently repeated for different users the lower user number will take priority e Opening and closing reports are sent for the Installer code as No 01 with the appropriate subscriber number Each Master code and set of secondary user codes are sent as Nos 02 and 03 16 respectively in Contact ID format with the appropriate subscriber number in 4 2 it is 1 F F for anything greater than 14 79 Keypad Functions General Information Arming Functions Special AWAY Arming 2 Partition Arming Note that if you enabled QUICK ARM for the partition field 21 the key can be pressed instead of entering the partition s security code for any of the arming procedures Away Stay Instant Maximum etc The security code is always required however when disarming the system The keypad allows the user to arm and disarm the system and perform other system functions such as bypassing zones and display zone descriptors Zone and system conditions alarm trouble bypass are displayed in the
140. r to disarm or arm the system will send a silent duress message to the central station Keypad Panic Keys Up to 3 programmable panic key functions are provided Designated as Zones 95 96 99 Activated by wired amp wireless keypads Reported separately by partition distinguished by subscriber ID number Zone Monitor Feature The control will sense a high resistance in the loops on hard wired zones 2 8 if it is present and will display a trouble message rather than an alarm for the affected zone when the system is in the disarmed mode This feature also prevents the system from being armed while this high resistance condition exists Exit Error False Alarm Prevention Feature Enables the system to determine the difference between an actual alarm and an alarm caused by leaving an Entry Exit or Interior zone open after the exit delay expires If not disarmed in time an alarm will sound and an Exit Error report sent to the central station An Exit Alarm condition will also occur if an Entry Exit or Interior zone re opens within 2 minutes after the end of an exit delay Optional Output Relays and Powerline Carrier Devices X 10 type Up to 4 relays using one 4204 Relay Module Up to 2 relays using one 4229 Zone Relay Module Up to 8 Powerline Carrier devices you must subtract the number of relay outputs actually used by the 4204 or 4229 modules if used Actions programmable to respond to zone activity or manual keypad
141. re controlled by signals sent through the electrical wiring at the premises via a 4300 transformer Therefore if using Powerline Carrier Devices a 4300 transformer must be used in place of the regular system transformer sd Once a device is programmed into the system the user sees no difference between a Powerline Carrier device or a relay output device In 80 and 81 interactive modes a series of keypad prompts will reguest entries for programming of the Relay outputs and or Powerline Carrier devices used in the system Refer also to OUTPUT RELAYS POWERLINE CARRIER DEVICES WORKSHEET FOR 80 AND 81 INTERACTIVE MODES in the blank programming form 4204 and 4229 Relay Modules 4204 4229 Setup The 4204 or 4229 unit can be mounted either remotely or in the control panel The following steps should be taken to properly set up the 4204 or 4229 1 Connect the 4204 4229 to the control s Partition 1 remote keypad terminals 4 7 using the connector supplied with the 4204 and 4229 Use standard 4 conductor twisted cable for long wiring runs 2 Set the 4204 4229 s DIP switch for a device address of 1 switch 2 OFF and switches 3 4 5 ON Switch 1 determines the unit s cover tamper response ON disabled OFF enabled 3 Connect the desired field wiring to the unit s relay contact terminals Supervision e 4204 and 4229 modules are supervised against removal CHECK and zone 09 will be displayed if a mo
142. re provided in the programming sections of this manual for specific programming details 31 Section 8 FA4285 PHONE MODULE This section provides instructions for mounting and wiring the FA4285 Phone Module Installing the Phone Module General Information The FA4285 Phone Module is an add on accessory for the FA162C that permits access to the security system via a Touch tone phone either on premises or by a call in when away The Phone Module can announce many of the same words that would normally be displayed on an Alpha keypad under the same system conditions A e Only one Phone Module can be used in this security system and only in Partition 1 e When using the FA4285 Phone Module addressable keypads must be used in the system but set to the non addressable mode address 31 When properly connected the FA4285 Phone Module will enable the user to do the following via a Touch tone telephone a Receive synthesized voice messages over the phone regarding the status of the security system b Arm and disarm the security system and perform most other commands using the telephone keypad with voice annunciation being provided over the phone as confirmation after any command is entered The phone used for phone access must have Touch tone capability though Touch tone service is not necessary if premises uses PULSE dialing switchable phones must be set for Touch tone temporarily before attempting phone ac
143. remote Keypads for Partition 2 to the 4 pin connector on the control board see the Summary of Connections diagram for location of the 4 pin connector for partition 2 KEYPAD CONNECTOR CABLE SUPPLIED WITH VISTA 20 M632 5 2 GREEN PARTITION 1 KEYPADS PARTITION 2 KEYPADS CONTROL TERMINALS CONNECTOR PINS FOR PARTITION 2 ON CONTROL BOARD Figure 6 Keypad Connections To The Control Board Mounting the Keypads 1 Make sure keypads are set to non addressable mode address 31 which is the factory default setting Refer to the instructions provided with the keypad for address setting procedure 2 Mount the keypads at a height that is convenient for the user Refer to the instructions provided with the keypad for mounting procedure You can either surface mount or flush mount keypads using an appropriate Trim Ring Kit FA550TRK except FA210KP Refer to the mounting instructions and template included with the keypad and or trim ring kit for specific information Using a Supplementary Power Supply to Power Additional Keypads The control provides 600mA for powering keypads up to a maximum of 4 per partition and other devices from the auxiliary power output The backup battery will supply power to these keypads in the event that AC power is lost When the control s auxiliary power load for all devices exceeds 600 mA you can power additional keypads from a regulated 12VDC power supply eg 487 12 supplies 12V 250mA 488 12 s
144. rm Zones Currently in Trouble and RF Sensors with Low Battery Conditions MMM M MMM After the control and the PC have established valid communication each keypad on the system will become inactive and will display CC or MODEM COMM The control however will still be scanning its zones and looking for alarms If an alarm does occur after communication is broken off alarms are sounded and the proper dialer reports are sent to the central station The keypads will become active after the download communication is terminated The detailed operation of the download functions is covered in the installation instructions for the FADL Downloading Software Diskette Remote Programming Advisory Notes Y Alarm and trouble reporting may be delayed during the time that the system and the Downloader are linked to each other following a valid exchange of codes but the proper message will get through to the Central Station after the link is broken Y Keypad entries are ignored during the time interval stated above Y A copy of the program downloaded may be produced from the IBM PC compatible computer using the product s internal report generator when an optional printer is connected consult your PC manual for proper printer and connections 3 Program Upload or Download Time Approximately one minute fifteen seconds for a complete program 75 Section 22 SYSTEM COMMUNICATION This section provides an explanation of formats this sys
145. rmer from the AC outlet 35 Section 9 EXTERNAL SOUNDERS This section provides a list of compatible sounders and connection information for an external sounder Compatible Sounders AB 12M 10 Motorized Bell amp Box 1011BE12M 10 Motorized Bell amp Box 702 Outdoor Siren 719 2 Channel Siren 747 Indoor Siren 747UL Indoor Siren 744 Siren Driver 745X3 Voice Siren Driver 705 820 5 inch Round Speaker Motor bell amp box UL Grade A 100 mA current draw Motor bell amp box UL Listed 100 mA current draw Self contained 6 12 volt siren driver built in and weatherproof for outdoor use Can be wired for either a steady or warble sound Two channel self contained 6 12 volt siren driver built in 109dB 10 feet 550mA current draw Self contained 12 volt siren driver built in for indoor wall mount 747F available for flush mounting Self contained siren driver built in for indoor wall mount UL Listed 6 jumper selected sound outputs Rated at 119dB with use of an 8 ohm 30 watt speaker Voice siren driver with English Spanish and French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed 15 watt 8 ohm speaker 713 Speaker 40 watt 8 ohm indoor outdoor speaker System Sensor PA400B beige PA400R red Indoor Piezo Sounder Indoor piezo sounder red or beige rated at 90 dB Q 10 feet UL e Use only UL Listed sounding de
146. rom partition 1 s keypad For multi partition systems make sure all partitions are disarmed before entering this mode Once you have placed transmitters in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter s screw terminals if used fault each transmitter Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results Note On button type transmitters whose buttons have been set to Arm Away Arm Stay or Disarm pressing a button will take the system out of the Go No Go Test mode and cause that action a The keypad will beep three times to indicate signal reception and display the appropriate zone number b If the keypad does not beep reorient or move the transmitter to another location Usually a few inches in either direction is all that is required If each transmitter produces the proper keypad response when it is faulted you can then permanently mount each of the transmitters according to the instructions provided with them Exit the Go No Go test mode by entering Installer code 4112 OFF Unplug the AC transformer Setting DIP switches on the 5827 Transmitter s A 5827 transmitter must be set to the programmed House ID using its DIP switches SWITCH UP FOR ON 5827 Wireless Keypad DIP Switch Table DIP SWITCH POSITION DIP SWITCH POSITION 5 2 4 TTT a UP 12345
147. rs Compatible 4 Wire Smoke Combustion Detectors No 1321 16 5VAC 25VA Plug In Transformer No 4300 Powerline Carrier device Interface AC Transformer Ademco AB 12M 10 Motor bell amp box UL Grade A 100 mA current Motorized Bell amp Box draw Ademco 1011BE12M 10 Motor bell box UL Listed 100 mA current Motorized Bell Box draw Ademco Self contained 6 12 volt siren driver built in 702 Outdoor Siren and weatherproof for outdoor use Can be wired for either a steady or warble sound Ademco 719 Two channel self contained 6 12 volt siren 2 Channel Siren driver built in 109dB 10 feet 550mA current draw Ademco 747 Self contained 12 volt siren driver built in for Indoor Siren indoor wall mount 747F available for flush mounting Ademco 747UL Self contained siren driver built in for indoor Indoor Siren Ademco 744 Siren Driver wall mount UL Listed 6 jumper selected sound outputs Rated at 119dB with use of an 8 ohm 30 watt speaker Ademco 745X3 Voice siren driver with English Spanish and Voice Siren Driver French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed Ademco 705 820 15 watt 8 ohm speaker 5 inch Round Speaker Ademco 713 Speaker 40 watt 8 ohm indoor outdoor speaker System Sensor PA400B Indoor piezo sounder red or beige rated at 90 beige PA400R red dB 10 feet Indoor Piezo Sounder System Sensor 2300T 2400 2400TH
148. s with a zone number and a once per minute beeping at the keypad indicates that a low battery condition exists in the wireless sensor displayed zone 00 indicates a wireless keypad If the battery is not replaced within 30 days a CHECK display may occur Note Some wireless sensors contain a non replaceable long life battery which requires replacement of the entire unit at the end of battery life e g Nos 5802 5802CP 5803 A display of 94 Fixed word keypads or Telco Fault Alpha keypads indicates that a monitored telephone line if programmed in field 92 has been cut or disconnected Depending on how the system was programmed the keypad may also produce a trouble sound and the external sounder may be activated silence by entering installer code plus OFF e If there is no keypad display at all and the POWER indicator if present is not lit operating power for the system has stopped and the system is inoperative e If the message AC LOSS Alpha keypads or NO AC Fixed word keypads is displayed and the POWER indicator if present is off the keypad is operating on battery power only e If the battery standby capacity is used up during a prolonged AC power outage the control s auxiliary power will shut down to minimize deep discharge of the battery Busy Standby dI If this remains displayed for more than 1 minute the system is disabled Modem Comm CC The system is in communication with the c
149. s a special purpose zone type used with 5800 series wireless pushbutton units which will result in arming the system in the STAY mode when the zone is activated Pushbutton units send zone number as a user number to central station when arming or disarming This is a special purpose zone type used with 5800 series wireless pushbutton units which will result in arming the system in the AWAY mode when the zone is activated Pushbutton units send zone number as a user number to central station when arming or disarming This is a special purpose zone type used with 5800 series wireless pushbutton which will result in disarming the system when the zone is activated This zone type can be used on a zone when an output relay action is desired but with no accompanying alarm e g lobby door access This zone type provides an instant alarm with NO audible indication at any keypad or external sounder if the zone is faulted when the system is armed in the AWAY STAY INSTANT or MAXIMUM modes This zone type is usually assigned to all sensors or contacts on exterior doors and windows where bells and or sirens are NOT desired A report is sent to the Central Station NOTE All of the zone types described are available for the wireless portion of the system if used 46 Section 15 DATA FIELD DESCRIPTIONS Descriptions of System Data Fields THE BLANK PROGRAMMING FORM SHOULD BE USED TO RECORD THE DATA FOR THIS INSTALLATION Defaults where appl
150. s information must be provided to the telephone company This equipment uses the following jacks An RJ31X is used to connect this equipment to the telephone network The REN is used to determine the quantity of devices which may be connected to the telephone line Excessive RENS on the telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENS contact the telephone company to determine the maximum REN for the calling area If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required If advance notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact the manufacturer for repair and warranty information If the trouble is causing harm to the telephone n
151. s time press 0 Ae E4 or E8 displayed 4c More zones have been programmed than the zone expansion modules can handle Delete some zones or use a higher capability RF receiver 4d Keypad address setting incorrect 4d Keypads must be set for address 31 non addressable mode SMOKE DETECTOR POSSIBLE CAUSE L Detector alarms no Dust dirt in sensing chamber Clean unit s sensing chamber with apparent reason vacuum cleaner per unit s instructions Improper location See unit s instructions for locations to avoid Relocate as necessary Unit malfunctioning Replace detector 2 Detector s siren sounds Unit not receiving required power Check for proper installation of battery Try new battery Unit malfunctioning Replace detector 86 CONTACTING TECHNICAL SUPPORT PLEASE Before you call Technical Support be sure you e READ THE INSTRUCTIONS e Check all wiring connections e Determine that the power supply and or backup battery are supplying proper voltages e Verify your programming information where applicable e Note the proper model number of this product and the version level if known along with any documentation that came with the product e Note your First Alert customer number and or company name Having this information handy will make it easier for us to serve you quickly and effectively You may contact Technical Support via Toll Free Fax Please include your ret
152. satisfied with the serial and loop number combination that has been enrolled regardless of whether or not the enrolled input has been confirmed This will ready the system to enroll the next transmitter If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the LEARN S N prompt A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 Yes or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop input 7 The system will search for the next zone that does not have a serial number associated with it If one is found the prompt in step 5 along with the appropriate zone number will be displayed Follow steps 5 and 6 for the remaining wireless zones When the last zone has been enrolled the display will remain on that zone To exit this mode and return to data field program mode press When you have finished programming all zones test each using the system s TEST mode Do not use the Transmitter ID Sniffer mode for this as it will only check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop 73 Section 21 REMOTE PROGRAMMING AND CONTROL DOWNLOADING
153. se ERENS Ne ENEE Se eg AR NE Gee Ee ee 8 63 Output To Long Range Radio esse see 48 PAAOOB Lidia 91 PAAOOR RE EE EE i 36 PABX Access COde i e EE kes DES EERS Pe egg EG ER EDE amp 50 Panic Keys iis Eie ESEG acne Ne SEE GO BR ee RSG RE GEN eie ee 81 Partition Default i e se EE ese De se GER Ee 58 Partitions sde Ae e AT eegen reen deefe degen de 7 Perimeter Burglary iese esse ese ee ee ed 45 Periodic Test Report sietos iue see a Re 51 Phone Line se di Ee EE es EE Gee ee EE Eg 12 Phone Line Monitor Enable iese esse ee Re RR 55 Phone Module 12 82 33 34 56 81 Phone Module Access Code ii iese Re 48 Phone System Select iese RA RA Re 50 Power Failure iss ees ee Re RA Re Re trenie Re ee 82 Power LED anida tt edd 41 Power Up In Previous State esse sesse ese ee Re ee 49 Powerline Carrier device Re RA Re 64 Powerline Carrier Device 1 X 10 House Id 48 Powerline Carrier devices o 8 9 29 30 63 81 Primary Phone NO iese esse esse ee ee ee ee ee 50 Primary Subs Account NO esse esse esse ee ee AR 50 Program Upload or Download Time sesse sesse esse 75 Programming Information sesse esse see see ed ee ee 43 Pulse Dialing ies see SEN i sae see ENEE 32 Quick Arme ao Ea 43 47 80 Radionics Sescoa orete ie ine seisein iiaia 89 Ready GED EE 41 Receiver Supervision oocoonocccnnonncnnonnnnnonnnnnnoncnnnnncncnononos 23 Peed Witch iii Eesen 71 Relay GUtPULS ic
154. sed All detectors must be wired in parallel A You must connect the EOL resistor across the loop wires at the last detector Remove 2000 ohm EOL resistor if connected across the selected zone terminals 3 To supervise power we recommend the use of a System Sensor No A77 716B supervisory module AUX PWR OUTPUT TERMINALS _ O 4 WIRE SMOKE OR COMBUSTION POWER je N DETECTORS del SUPERVISION Ei d E Ss SI RELAY MODULE A77 716B 2000 OHMS TO HI SIDE OF EOLR SELECTED ZONE ZONES 2 7 TO LO SIDE OF SELECTED ZONE IF PROGRAMMED FOR FIRE DETECTOR Figure 9 4 wire Smoke Detector Connections Zones 2 7 BER COMPATIBLE 4 WIRE SMOKE COMBUSTION DETECTORS 1412 System Sensor 4 wire ionization products of combustion detector 2412 System Sensor 4 wire photoelectric smoke detector 2412TH System Sensor 4 wire photoelectric smoke detector w 135 F 57 C heat detector A77 716B System Sensor EOL relay module supervisory module for wired 4 wire fire zone 2112 24T System Sensor low profile 4 wire photoelectric smoke detector w 135 F 57 C heat detector Wiring 2 Wire Latching Glass Break Detectors On Zone 8 Use zone 8 for connection of compatible 2 wire latching type glass break detectors After an alarm the first code OFF turns off the siren and disarms the system the second code OFF clears the memory of alarm and resets the glassbreak detector
155. sh to change the existing descriptor for zone 1 enter plus the next zone number for which you wish to enter or check a descriptor A summary display for that zone will appear You must then press plus the same zone number again to gain access to the entry mode flashing cursor for that zone Flashing Cursor 6 Press 4 plus 3 digit number for the first word from the Alpha ZN 01 BACK Vocabulary List Example The descriptor that we wish to enter for zone 1 is BACK DOOR From the list BACK 013 Therefore you would enter 01 3 Note If you accidentally enter the wrong word simply press plus the correct 3 digit number for the word you want zZNO1 BACK 7 Press 6 to accept the selected i word and continue NOTE If this is the only word you are using for the descriptor press 8 instead of 6 to save that word in memory and then go to step 11 Flashing Cursor if 6 is pressed system is ready for next word 8 Enter the 3 digit number for the ZN 01 BACK next word In our example the word DOOR is DOOR whose number is 057 Enter 05 7 This display will Flashing Cursor appear 67 ZN 01 BACK 9 Press 6 to accept the selected word DOOR NOTE If these are the only words you are using for the descriptor press 8 instead of 6 to save them in memory Flashing Cursor i
156. tem accommodates for reporting alarms and other system conditions to the central station The process of a successful transmission consists of both the method of communication between the control panel and the central station receiver and the actual way the information is sent and displayed at the central station Report Code Formats When the panel calls the central station receiver it waits to hear a handshake frequency from the receiver to confirm that the receiver is on line and ready to receive its message Once the panel hears the handshake it is programmed to listen for it sends its message The panel then waits for a kissoff frequency from the receiver acknowledging that the message was received and understood If the handshake frequency is not given or is not understood by the panel the panel will not send its message Once the handshake frequency is received and understood by the panel the panel will send its message If there is an error in the transmission the receiver does not receive a valid message the kissoff frequency will not be given by the central station receiver The panel will make a total of eight attempts to the primary telephone number and eight attempts to the secondary telephone number if programmed to get a valid message through If the panel is not successful after its numerous attempts the keypad will display Communication Failure Alpha keypad or FC Fixed word keypad The
157. teractive Mode sirain ra 25 Interior w Delay oooocccnocnnonoccnononcnnoononcnnnnnnnonnnnnnnnnnnnnnnoss 46 Interior Follower ooooocnnocccnnoncnnnonncnnornncnoncncnnnnnnnnnnoss 45 Keypad Connections ccooocccnonncnoonnnnoncnononcnnnnnnnnoncncnnnnonno 15 Keypad Panic Keys ienei AEs 8 Keypads eege deeg EO N EE 14 15 KisSO EE Re EE EE es DE Ge a EPEA 76 Rolle ee de N GE Ee GE dd 58 Enrolled WEE 25 Enrolling ui rn 26 Line Seizure Wiring ooooccnnooccnoocncnonnnnnonononononononcnnnonnnnnno 34 A ME be a i 10 Long Range Radio iese esse ee ee AR ee 9 38 Low Bat Report Code oooconoccconoccnooonccoonnncoonnncnoncncnancnnnnns 53 Low Bat Restore Report Code iese 54 Low Battery Message sees ss see RA 42 85 LRR Communication Failure esse esse see ee ee 82 ETE OOR OE OR RE EE EO 71 85 Main Pe Board EE EE ER eal Aneta id 10 EES GO RE OE EE N N EE enters 79 fa OE N ee 43 Monitored Telephone Line ocoonccnnccnonccnocononnconncnonaconnc n 82 No Alarm Response E ea Re RA RA 46 No4300 ita RE Ge SE eves cages EEN loins ee ee 91 No 467 12V 4AH battery esse eene see RR RR 41 NOs AT 72 TIGB ia lt 18 Non Removable Battery esse esse se Re Re Re 71 Number Of Reports In Armed Period AAA 55 Off Premises On Premises Phone eise esse esse 35 Open Report Code iese AR RR Re 53 Optima 24 Plus FAX96 Modem A 74 Option Selection RA RA varisi 55 Output Devices EE SE ES EER id 61 Output Relays ie
158. tery size needed use the following formula Total Current Drawn x Number of hours standby wanted Battery Ampere Hours Convert mA figure to decimal Amps see example Example If total auxiliary device current drawn is 450 mA add 100 mA for the control panel for a total of 550 mA 0 55 amps if 24 hour standby is wanted the calculation will be 0 55 mA x 24 hours 13 2 Ampere Hour battery needed In this example two 7 Amp Hr batteries connected in parallel must be used 41 Making the Battery Connections 1 Use the battery standby formula above to select the appropriate battery for the installation 2 Do not connect the battery until all devices have been wired to the control 2 Attach the Red and Black wires on the battery connector cable as follows a Red to the positive battery tab on the control board b Black to the negative battery tab on the control board See the SUMMARY OF CONNECTIONS diagram for location of the and battery tabs on the control board 3 Attach the Red and Black wires at the other end of the battery connector cable as follows a Red to the positive terminal on the battery b Black to the negative terminal on the battery Battery Tests The battery is periodically tested automatically approximately every four hours and if it cannot sustain a load a low battery message is displayed and if so programmed will be reported to the central station
159. the READY TO ARM message should appear again If some wired expansion zones have been assigned to partition 1 and others to partition 2 you will need to observe the keypad in the appropriate partition as each zone in that partition is faulted and restored When you get the proper displays on the keypad s the wired expansion zones in the system are functioning properly Unplug the AC transformer not reaching the zone expander module or the tamper switch is activated A If a CHECK 09 message appears on the display data from the control is Check the wiring and DIP switch settings 29 Section 6 WIRELESS EXPANSION 5800 SYSTEM This section provides instructions for installing 5800 series wireless receivers and transmitters General Information In addition to its basic wired zones the control supports up to 30 wireless zones using an appropriate 5881 5882 in Canada type RF receiver The actual number of zones supported depends on whether you are using a wired zone expander module For example If you are using only four of the wired expansion loops a 5881H 5882H in Canada RF Receiver could add 26 RF zones to the system using any unused zone numbers 10 38 for a combined total of 30 wired and wireless expansion zones The receiver can detect signals from wireless transmitters within a nominal range of 200 feet RF Receiver No of Zones 58811 5882L up to 8 5881M 5882M up to 16 5881
160. the event an intruder hides on the premises prior to the system being armed or gains access to the premises through an unprotected area Type 05 This zone type will give an instant alarm if faulted when armed in the Away Trouble by Day Stay Instant or Maximum night modes During the disarmed state day Alarm by Night the system will provide a latched trouble sounding from the keypad and a central station report if desired This zone type is usually assigned to a zone which contains a foil protected door or window such as in a store or to a zone covering a Sensitive area such as a stock room drug supply room etc This zone type can also be used on a sensor or contact in an area where immediate notification of an entry is desired 45 Type 06 24 hour Silent Alarm Type 07 24 hour Audible Alarm Type 08 24 hour Auxiliary Alarm Type 09 Supervised Fire With Verification on Zone 1 Type 10 Interior w Delay Type 20 Arm Stay Type 21 Arm Away Type 22 Disarm Type 23 No Alarm Response Type 24 Silent Burglary This zone type sends a report to the Central Station but provides no keypad display or sounding This zone type is usually assigned to a zone containing an Emergency button This zone type sends a report to the Central Station and provides an alarm sound at the keypad and an audible external alarm This zone type is usually assigned to a zone that has an Emergency button This zone type se
161. there is a secondary phone number field 42 SECONDARY PHONE No See Box at Left ENE tte ot bt tt tt Enter up to 16 digits If fewer than 16 digits entered exit by pressing and next field number e g 43 To clear entries from field press 42 See back up reporting note for field 41 If using the pager feature enter the pager phone number here PRIMARY SUBS ACCOUNT No partition 1 II See box at left SECONDARY SUBS ACCOUNT No partition 1 II See box at left PRIMARY SUBS ACCOUNT No partition 2 II See box at left SECONDARY SUBS ACCOUNT No part 2 See box at left PHONE SYSTEM SELECT 1 If Central Station Receiver is not on WATS line 0 Pulse Dial 1 Tone Dial If Central Station Receiver is on WATS line 2 Pulse Dial 3 Tone Dial REPORT FORMAT 7 0 0 3 1 4 1 ADEMCO Low Speed Standard 1 3 1 4 1 Radionics Standard 2 412 ADEMCO Low Speed Standard 3 4 2 Radionics Standard 6 4 2 ADEMCO Express 7 ADEMCO Contact ID Reporting 8 3 1 4 1 ADEMCO Low Speed Expanded 9 3 1 4 1 Radionics Expanded Enter as the 4th digit of 43 through 46 if 3 1 dialer reporting is to be used Prim Sec For an explanation of these formats see the SYSTEM COMMUNICATION section Note The maximum number of alarm and alarm restore reports during one armed period is determined by field 93
162. ts with a small screwdriver Two keypad beeps will occur when the detector is faulted the first time b Wait 6 8 seconds then press and release the test switch or momentarily short the contacts again 3 beeps will occur if the control has accepted the input code and a summary display showing the enrolled input loop No will appear 5816 Door Window Has two unique input loop zones one for a wired closed circuit contact loop Transmitter and the other for a built in reed switch used in conjunction with a magnet Either or both may be used Enroll as 3 for RF supervised 5817 Multi Point Universal Has three unique input loop codes one for a DIP switch set Primary Transmitter contact loop and the others for two Auxiliary closed circuit contact loops e The Primary loop may be set for a Repeating or Single Transmission b Normally Open or Normally Closed Circuit c Slow or Fast Response d 3 Minute or No Transmission Inhibit DIP Switches Set all DIP switches to the OFF position when enrolling the serial number Enroll as 3 for RF supervised Note All loops must be assigned the same Input Type 5818 Recessed Magnetic Enroll as 3 for RF supervised Contact Transmitter 5819 Shock Processor Has three unique input loop zones one for a wired closed circuit contact loop Transmitter one for use with inertia type shock detectors mounted externally and one for a built in reed switch used in conjun
163. tter ID Sniffer mode for this as it will only check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop 60 Section 17 OUTPUT DEVICE PROGRAMMING 80 Menu Mode Programming Options Defined The following will help you understand the programming of Output Devices when using 80 and 81 modes The options used to start and stop these devices are described below followed by the actual screen prompts and available entries IMPORTANT Relays The letter s in parentheses after each function described below such as A and output devices are not after ACTION are those that appear in the various summary displays of recommended for life programmed data during programming safety applications ACTION A The ACTION of the device is how the device will respond when it is activated by the START programming There are four different choices of actions e ACTIVATE for 2 SECONDS and then reset e ACTIVATE and REMAIN ACTIVATED until stopped by some other event e PULSE ON and OFF until stopped by some other event e NOT USED when the device is not used START STT The START programming determines when and under what conditions the device will be activated The following START options are available Start By Event 1 Event EV is the condition Alarm Fault Trouble that must occur to a zone or group of zones zone list in order to activate the devic
164. type that restores will de activate the device 61 STOP STP If a SYSTEM OPERATION is chosen e g End of Exit Time that operation will cause the device to activate as selected in ACTION The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Output Relays Powerline Carrier devices later in this section and in the Programming Form Partition No P The device s Start ZONE TYPE SYSTEM OPERATION may be limited to an occurrence on Partition 1 Partition 2 or any partition A The STOP programming determines when and under what conditions the device will be de activated The following options are available Upon Restore of a Zone List Restore Zone List ZL If a ZONE LIST is used as the Stop event the device will de activate when all the zones in that list restore from a previous fault trouble or alarm condition This will occur regardless of what is programmed to START the device therefore a RESTORE ZONE LIST would normally only be used when a ZONE LIST is used to start the device Upon a Zone Type or System Operation Zone Type System Operation ZT Instead of using a RESTORE ZONE LIST a specific zone response type or system operation action can be selected to de activate the device If a specific ZONE TYPE is chosen any zone of that response type that restores from a previous alarm trouble or fault condition will cause the device to
165. upplies 12V 500mA Use a UL Listed battery backed supply for UL installations The 487 12 488 12 power supplies have a backup battery which can power these keypads in the event of AC power loss not function when AC power is lost Therefore be sure to power at least A Keypads powered from supplies which do not have a backup battery will one keypad in each partition from the Control s auxiliary power output Connect the additional keypads as shown in Figure 7 using the keypad wire colors shown Be sure to observe the current ratings for the power supply used Make connections directly to the screw terminals as shown in Figure 7 Make no connection to the keypad blue wire if present Be sure to connect the negative terminal on the Power Supply unit to terminal 4 AUX on the control 15 SUPPLEMENTARY CONTROL POWER SUPPLY TERMINAL STRIP AUX AUX DATA DATA IN OUT 4 5 6 7 YO OD ZA EE IMPORTANT MAKE THESE CONNECTIONS DIRECTLY TO SCREW TERMINALS AS SHOWN TO KEYPAD GRN WIRE TO KEYPAD YEL WIRE TO KEYPAD GRN WIRE TO KEYPAD RED WIRE TO KEYPAD BLK WIRE TO KEYPAD BLK WIRE TO KEYPAD RED WIRE TO KEYPAD YEL WIRE Figure 7 Using A Supplementary Power Supply For Keypads Preliminary Check out Procedure If you want to check that the system is working before connecting field wiring from zones and devices do the following
166. urn fax number You will receive a reply within 24 hours You may also contact Technical Support via modem to ATLIS BBS Tech Support s Electronic Bulletin Board System Replies are posted within 24 hours Premier Gold Technical Support 800 538 5585 8 a m 6 p m E S T After 6pm E S T 800 421 5557 Please be sure to have your PIN number ready before calling Technical Support Fax Number 1 800 447 5086 ATLIS BBS Electronic Bulletin Board System 1 516 496 3980 1200 9600 Baud 8 Data Bits 1 Start Stop Bit No Parity REGULATORY AGENCY STATEMENTS UL NOTICE This is a Grade A residential system FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television rec
167. ve Mode Programming 56 80 81 82 and 83 Typical prompt displayed Press plus interactive mode no for example 56 The Alpha keypad during interactive mode will display the first of a series of prompts requesting entries programming A detailed procedure with displays of prompts is provided in later sections 00 Quit Interactive Mode Used To Program Zone Number 56 Zone Programming Zone characteristics report codes alpha descriptors and serial numbers 80 Relay Programming 4229 or 4204 Relay modules or Powerline Carrier devices 81 Zone List Programming Zone Lists for relay powerline carrier activation 82 Alpha Programming Zone alpha descriptors 83 Sequential Mode 5800 series transmitter serial numbers Loading Factory Defaults To load the factory defaults enter the programming mode press 97 then exit the programming mode Do not press 97 to load defaults if any programming has been done previously data already programmed into the system will be changed 96 resets all the Subscriber Account numbers and CSID in preparation for an initial download Programming System Setup Fields The following program fields must be programmed before doing any zone programming 22 RF SYSTEM 0 Enter 1 if 5881 5882 RF receiver is being used enter 0 if no receiver is being used Default is 0 none 25 WIRED ZONE EXPANSION E Use this field to select the type of expansion
168. ver can identify a true low battery situation thus allowing time to arrange a change of battery to maintain protection for that given point within the system Installing an alarm system may make the owner eligible for a lower insurance rate but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property We continue to develop new and improved protection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments 98 SNOLLOANNOO JO AHVWWNS OZ91VA ZZ 21514 BATTERY FUSE W ADEMCO No 4219 SET UNIT S DIP GEL LEAD ACID TYPE an FOR REPLACEMENT REMOTE 2 WIRED EXPANSION MODULE SWITCH FOR BATTERY NORMALLY NEED NOT BE USE SAME VALUE KEYPAD as 8 ADD L EOLR WIRED ZONES DEVICE AUX PWR 4 DI REPLACED FOR AT LEAST 3 YRS ADEMCO No 90 12 9 PIN CONNECTOR 29 OR IW ADDRESS OUTPUT BIK RED BATTERY CAPACITY FOR EMERGENCY es EL RARTITION 2 USED FOR 4900 RS ADEMCO No 4229 OCH TERMS De dd TRANSFORMER E i EE ag STANDBY USE AT LEAST 4 HOURS WIRED EXPANSION RELAY MODULE SI i OSONNECTIONS FOR 25 pik 8ADD LEOLR WIRED ZONES PLUS 2 INSTRUCTIONS POWER a 8 E BLACK CONNECTOR osd CARRIER DEVICES 20 SE RELAYS __ suren BATTERY
169. vice Menu Mode This mode is used to program all output devices used in the system 4229 or 4204 Relay modules or Powerline Carrier devices Refer to the output device table for 80 on the separate programming form when programming output devices NOTE If using Powerline Carrier Devices the House ID of the devices must be entered in data field 27 After entering 80 the following prompts are displayed Enter the Device Number 01 or 02 for a 4229 or 01 02 03 or 04 for a 4204 or 01 08 for Powerline Carrier devices or 00 to end these entries Press the key to continue The key is used to accept an entry and advance to the next prompt The 4 key is used to revert back to the last question to check or change an entry Press to go forward again This screen displays a summary of the current Device START programming for this example device 02 has been selected Press the key to continue This screen displays a summary of the current Device STOP programming Press the key to continue Enter the desired device action as listed below Press the key to continue 0 No response 2 Close and Stay Closed 1 Close for 2 seconds 3 Continuous Pulse on amp off 1 sec ON 1 sec OFF Enter the event to START the relay 0 Not used 2 Fault 1 Alarm 3 Trouble A zone list must be used in conjunction with an event If a zone type system operation is to be used instead of an event enter
170. vices for UL installations e The total current drawn from the alarm output and the auxiliary power output combined cannot exceed 700 mA In addition the sounding device must be a UL Listed audible signal appliance rated to operate in a 10 2 13 8 VDC voltage range and must be mounted indoors Example Wheelock Signals Inc siren model 34T 12 provides 85dB A for NFPA 74 amp Standard 985 This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances Temporal pulse sounding for a fire alarm consists of the following 3 pulses pause 3 pulses pause 3 pulses 36 Sounder Connections The FA162C provides a 12 VDC output which can power external alarm sounders bells or sirens see compatible sounders listed previously This output will activate a sounder when an alarm occurs in partition 1 or 2 Make connections to alarm output terminals 3 and 4 See Figure 17 Non UL Installations The total current drawn from this output cannot exceed 2 amps A battery must be installed since this current is supplied by the battery AN Going beyond the limits indicated 2 amps will overload the power supply or may cause the electronic circuit protecting the sounder output to trip Testing the Sounder CONTROL BOARD NO 702 ALARM OUTPUT Figure 17 Typical Sounder Wiring After installation of the sounder is completed each partition o
171. ypass an answering machine and a FA4285 Phone Module is included in the system you should note the following When calling in from an off premises phone the user should make the initial call allow 1 to 3 rings only then hang up The user should then call again The Phone Module will now seize the line and 2 long tones sound followed by the usual voice prompt for the 2 digit access code If this procedure is not followed Phone Module operation will not be possible 95 RING DETECTION COUNT FOR DOWNLOADING 0 0 15 number of rings before control picks up phone line Refer to the chart below and program this field accordingly Phone Answering Module Machine E Field 95 Set for value other than 0 1 14 This will enable the control panel to answer the phone call Otherwise it will not be possible to access the Phone Module Set for a value higher than the number of rings for which the answering machine is set Example if machine is set for 4 rings use a value of 5 or higher This is recommended so that the Phone Module can still be accessed if the answering machine is turned off and does not answer the phone call Set for value other than 0 1 14 Enter 15 to bypass answering machine OTHER 56 ZONE PROGRAMMING MODE PROGRAMMING Interactive menu mode used for programming zone attributes and COMMANDS report codes Refer to the ZONE PROGRAMMING section for procedure 8
172. zone number to be enrolled e g zone 12 The system will search for that zone and will display the prompt shown in the beginning of step 5 If you wish to exit the enroll mode completely enter 00 and press 10 INPUT S N L A 022 4064 3 Serial Loop The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the serial and loop numbers and cause the keypad to beep twice If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system will not display the serial number but will wait for a transmission from another transmitter or transmitter loop input 6 The system will then enter an optional confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone 72 10 CONFIRMED A022 4064 3 When the system sees activity on the appropriate input it will beep three times and display the confirmation message Press or the upper left hand button of the program tool to when you are ready to enroll the next transmitter At any time during this step you may press the key on the keypad or the upper left hand button of the program tool if you are

FirstAlert FA162C - Protectron Security Systems

Contents

Download Pdf Manuals

Related Search

Related Contents