Owner`s Manual
Contents
1. DUES I2 Standard Weight Bench With Leg Lift CAUTION Maximum Weight Limit is 250 lbs This includes the user s body weight Lo SeA ENE aem L y i 7 Photo may differ from actual product Weights VVeight Set amp Dumbbells Sold Separately This product is for consumer use only and it is not meant for commercial use OWNER S MANUAL SAFETY AND CAUTION WARNING E Before Using Read All The Warnings And Obtain Instruction On The Use Of This Machine Use Only For Intended Exercise DO NOT Modify The Machine L Before Beginning Any Exercise Program Consult With Your Doctor Or Health Physician E Refer To The Manual Whenever You Have A Question E Keep All Body Parts And Clothing Free From All Moving Objects And Parts Of This Machine L Always Use A Spotter When Attempting To Workout E If The User Needs More Assistance Please Contact A Technical Consultant Before Attempting To Use The Machine L Keep Your Fingers Body Parts Children And Pets Away From Moving Parts LJ Warm Up Before Each Workout And Cool Down After Each Workout Q Do Not Allow Children Near This Equipment Teenagers Must Be Supervised E Inspect The Machine Before Each Use Make Sure All Of The Connections Are Tightly Secured E Do Not Over Tighten The Bolts Or Screws As It Could Result In Bending The Steel Or Plastic L Inspect The Machine For Tears And Broken Welds And Make Sure To Do Routine Maintenance On T2. EST ADJUSTMENT TUBE 13 is an adjustable tube for incline or flat operation Install on the top notches ensuring that the tabs go into the small holes located on the adjustment brackets as shown B Assemble the two sections of the BACKREST TUBE 11 12 as shown using one HEX BOLT 20 two WASHERS 24 and one NYLON NUT 27 Repeat this step for the opposite side C Insert the LONG BOLT 16 through the holes at the end of both the BACKREST TUBES 12 and the tube on the FRONT MAIN FRAME 6 and secure them from both sides using two WASHERS 23 and two NYLON NUTS 26 CZ NS N Z N a N N A g S SEAT PAD ASSEMBLY STEP 5 A Assemble one PAD 35 first at the BOTTOM using two HEX BOLTS 21 and two WASHERS 24 DO NOT over tighten hardware as this may damage your pad B The LARGE PAD 36 must be the CENTER pad for proper assembly Secure the LARGE PAD 36 with four HEX BOLTS 20 and four WASHERS 24 C Secure the other PAD 35 on TOP with two HEX BOLTS 20 and two WASHERS 24 Page 13 FINAL CHECK e Make sure all bolts are tightened e Check for loose parts and components e Check to see if there are any tears or bends in the welding or metal e Be sure that all adjustment locking devices and safety devices are properly located and fully engaged prior to use Page 14 Thanks for choosing ESODO N 4 AE Model Number WB 125 Please fill in the information below and keep
3. U O la Ta easeerrcsivinter gt a fosan Cd Dawe amp The quantity may be different from the parts listed because some parts are pre assembled on the unit PARTS LIST 24 oss oio washer OC 25 5 16 x8 Ot Nylon Nut 9 26 3 8 10t Nylon Nut a Ca fwxeorwinme Cid 28 hiasi Sure mere iY 29 i ivarxa st sare ner Plug 30 11x15 Souare Imer Plug at oxast Round ime Pug 32 eioxi s towa merei J2 ss osme o a an o oooO y e ee 36 Backrest Pad o t 37 User s waruat o Pace 7 The quantity may be different from the parts listed because some parts are pre assembled on the unit gt ns MO B DEDITA CI BAN The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the assembly process Please note that not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre installed Please continue to the next page to begin the assembly process and use this page only as a reference guide for parts and hardware UPRIGHT ASSEMBLY STEP 1 A Insert the RIGHT UPRIGHT ASSEMBLY 1 into the DOWN UPRIGHT ASSEMBLY 3 as shown in diagram Repeat the same procedure to insert the LEFT UPRIGHT ASSEMBLY 2 into the other DOWN UPRIGHT ASSEMBLY 3 B Hold the REAR CROSS TUBE 4 in place and secure the REINFORCEMENT PLATE 14 on the right using two HEX BOLTS 15 four WASHERS 22 an
4. d two NYLON NUTS 25 as shown Repeat the same procedure to secure the REINFORCEMENT PLATE 14 on the left QF MAIN FRAME ASSEMBLY STEP 2 A Insert REAR MAIN FRAME 5 into FRONT MAIN FRAME 6 B Secure with one REINFORCEMENT PLATE 14 on each side using two HEX BOLTS 15 four WASHERS 22 and two NYLON NUTS 25 as shown in the diagram C Install FRONT UPRIGHT 7 TO FRONT MAIN FRAME 6 and secure with three HEX BOLTS 17 and three WASHERS 22 D The REAR MAIN FRAME 5 and FRONT MAIN FRAME 6 may now be assembled to the REAR CROSS TUBE 4 by securing a REINFORCEMENT PLATE 14 with two HEX BOLTS 15 four WASHERS 22 and two NYLON NUTS 25 as shown in the diagram Page 10 LEG DEVELOPER ASSEMBLY STEP 3 A Install LEG DEVELOPER 8 to the FRONT UPRIGHT 7 which is attached to the MAIN FRAME ASSEMBLY using one HEX BOLT 18 two WASHERS 23 and one NYLON NUT 26 Do not over tighten the HEX BOLT 18 as this will prevent the LEG DEVELOPER from 4 functioning smoothly B Insert TUBE 9 through the LEG DEVELOPER 8 and secure with one HEX BOLT 19 two WASHERS 22 and one NYLON NUT 25 Then apply the END CAP 33 to the end of TUBE 9 as shown in the diagram the LEG DEVELOPER 8 then slide in two FOAM z C Insert ROLLER TUBE 10 through the holes on l ROLLERS 34 as shown in the diagram 33 N 22 19 k JA 10 SF 34 BACKREST FRAME ASSEMBLY STEP 4 A The BACKR
5. he Unit Before Use E If The Parts In The Box Does Not Match The Owner s Manual Please Do Not Assemble And Contact The Customer Service Department Immediately For Assistance E If V Machine Is Not In Proper Working Condition As The Above Points Please Do Not Use The Machine Q This Product Is For Consumer User Only And It Is Not Meant For Commercial Use E If The User Does Not Follow These Warnings It Could Result In Serious Injury Or Even Death E The Minimum Suggested Clearance For Safe Exercise 7 Long 7 Wide WARRANTY INFORMATION Limited Warranty Body Flex Sports warrants your product against defects in materials and workmanship when used for the intended purpose under normal personal use and conditions provided that the product receives normal maintenance and care Any unauthorized alterations or improper assembly damaae will also void this warranty This warranty is valid for 1 year on Frame 90 days on Parts and Upholstery A proof of purchase must be presented No Exception for any warranty validation All of these are for the original owner only and warranty begins from the date of the purchase Body Flex Sports will provide a replacement part at no charge for any part found defective in material or workmanship during the warranty period Under no circumstances will the manufacturer be responsible for damages or failures that occur as a result of improper assembly or failure to operate the product correctly Cus
6. this manual along with your sales receipt as proof of purchase Serial Number Date of Purchase Retailer Body Flex Sports Inc 21717 Ferrero Parkway Walnut CA 91789 Phone 888 266 6789 Fax 909 598 6707 Email info bodyflexsports com Page 15 version 6 16 2009
7. tomer Service If any parts are missing or unusable please Do Not Return The Product To The Store From Which It Was Purchased Our dedicated Customer Service Staff is standing by to help you at gt Customer Service Center at 888 266 6789 gt Monday Friday 9 00 am to 5 00 pm Pacific Time Any parts you need will be happily mailed to you at your home Exchange and Returns For returns or exchanges contact the store where the purchase was made Because various vendors may observe different policies regarding returns and exchanges neither the manufacturer nor the distributor can guarantee the satisfactory return or exchange of your purchase Body Flex Sports Inc 21717 Ferrero Parkway Walnut CA 91789 Fax 909 598 6707 Email info bodyflexsports com BEFORE ASSEMBLY Take a few minutes to familiarize yourself with the parts and hardware included with your product IMPORTANT PLEASE NOTE SOME OF THE PARTS AND HARDWARE LISTED ON THE PARTS LIST ARE ALREADY PRE ASSEMBLED OR INSTALLED ON THE MACHINE Nylon Lock Safety Nuts A Itis only necessary to tighten the bolts and nuts to finger tight during the assembly process This will make it easier to complete certain steps by allowing more tolerance for all the parts to fit properly B Do not tighten all the nuts onto the bolts securely until after you have completed assembly of your product C Use wrenches pliers or ratchet and sockets to tighten the bolts and n
8. uts D The Nylon Nut should thread onto the Hex Bolt until the end of the Hex Bolt has broken through the Nylon insert inside the Nut Wiring and Loose Components A Check all wiring for rips and tears B Check the frame for any damage C Make sure all the hardware is included HARDWARE LIST IMPORTANT PLEASE NOTE The hardware listed below is a list of ALL the hardware used on your weight bench Some of this hardware is already pre installed on your product Do not be alarmed if you are missing any of these parts 15 5 16 X2 3 16 17 5 16 X5 8 18 3 8 X2 3 8 Hex Head Bolt Hex Head Bolt Hex Head Bolt Qty 8pcs Qty 3pcs Qty Ipe NN 16 3 8 X6 7 8 Bolt Oty Ipe a TCC i AA mm T 19 5 16 X1 3 4 20 M6X35 21 M6X15 Hex Head Bolt Hex Head Bolt Hex Head Bolt Qty lpc Qty 8pcs Qty 2pcs 22 98 5Xo17X1 5t 23 910 5X 20X1 5t 24 26 5X213X1 0t Washer Washer Washer Qty 2lpcs Qty 4pcs Qty 12pcs 25 5 16 X8 Ot 26 3 8 X10t 27 M6X6 Ot Nylon Nut Nylon Nut Nylon Nut Qty 9pcs Qty 38pcs Qty 2pcs PARTS LIST i men O o2 Upright Left 1 3 pom OE y y A a fws y Cs femara y y e fomm OOE O O a aome o h ooo wpe o BETES Backrest Tube Long 2 12 Backrest Tube Short 2 18 fiora u fenmen y y O Te 15 5 16 X 2 3 16 Hex Head Bolt 8 16 3 8 X 6 7 8 Bolt 1 5 16 X 5 8 Hex Head Bolt 3 18 3 8 X 2 3 8 Hex Head Bolt 1 19 5 16 X 1 3 4 Hex Head Bolt 1 a pos O e Ca vosen
Download Pdf Manuals
Related Search