Instructions for use
Contents
1. ASSEMBLY 1 Insert the antenna into the controller by tweak the antenna clockwisely 2 Lift the battery compartment door on the back of the controller and insert two AA LR6 batteries NOTE This product didn t included the AA LR6 batteries BATTERY INFORMATION Batteries may leak fluids that can cause chemical burn injury or ruin your product To avoid battery leakage e Do not mix old and new batteries e Do not mix different types of batteries alkaline standard carbon zinc or rechargeable nickel cadmium Insert batteries as indicated inside the battery compartment e Remove batteries during long periods of non use Always remove exhausted batteries from the product Battery leakage and corrosion can damage this product Dispose of batteries safely e Do not dispose of batteries in a fire The batteries may explode or leak e Never short circuit the battery terminals e Non rechargeable batteries are not to be recharged e Use only batteries of the same or equivalent type as recommended e f removable rechargeable batteries are used the are only to be charged under adult supervision e Remove rechargeable batteries from the product before charging e Batter chargers used with toys must be examined regularly for damage to the cord plug enclosure and other parts In the event that such damage is found the toy must not be used with the battery charger until the damage has been repaired OPERATION 1 Press the CONVER2. To avoid the fuse cut off the power follow these guidelines DO NOT overload the vehicle Maximum weight allowed 30kg DO NOT tow anything behind the vehicle DO NOT drive up steep slopes DO NOT drive into fixed objects which may cause the wheels to spin causing the motor to overheat DO NOT drive in very hot weather components may overheat DO NOT tamper with the electric system Doing so may create a short circuit causing the fuse to trip Battery POSSI BLE CAUSE Wheel nuts are loose If the nuts are not tight the wheels will not engage the forward gears Tighten the nut with the nut wrench POSSI BLE CAUSE Battery connector or wires are loose Make Sure the battery connectors are firmly plugged in to each other POSSI BLE CAUSE Battery is dead Have you properly maintained the battery according to the directions Is the battery old Your battery may need to be replaced POSSI BLE CAUSE Electric system is damaged Water may have corroded the system or loose dirt gravel or sand might have jammed the switch POSSI BLE CAUSE Motor is damaged The motor needs professional repair Mi PROBLEM The battery will not recharge POSSI BLE CAUSE Battery connector or adapter connector is loose Make sure the battery connector and adapter connector are firmly plugged together POSSI BLE CAUSE Charger is not plugged in Make sure the charger is plugged into the wall outlet and the power flow to the outlet Is on
3. POSSI BLE CAUSE Charger is not working Is the charger warm while charging If not the charger may be broken and may need to be replaced TROUBLESHOOTING GUIDE Mi PROBLEM The vehicle does not run very long POSSI BLE CAUSE Battery may be undercharged You may not be charging the battery long enough After each use or once a month minimum charge the battery for 8 to 10 hours Do not leave the battery on the charger for more than 20 hours POSSI BLE CAUSE Battery is old The battery will eventually lose the ability to hold a charge Depending on the amount of use and varying conditions the battery should operate for one to three years Replace the battery with a new one Mi PROBLEM Battery buzzes or gurgles when charging This is normal and not a cause for concern It may also be silent when charging which is also normal li PROBLEM Charger feels warm when recharging battery This is normal and not a cause for concern MAINTAINING YOUR VEHICLE It is parents responsibility to check main parts of the toy before using Must regularly examine for potential hazard such as the battery charge cable or cord plug screws are fastening enclosure of other parts and that in the event of such damage the toy must not be until that damage had been properly removed Make sure the plastic parts of the vehicle are not cracked or broken Occasionally use a lightweight oil to lubricate moving parts such as wheels Park the ve
4. ONLY Charge the battery in a dry area ONLY Battery posts terminals and related accessories contain lead and lead compounds chemicals known to the State of California to cause cancer and reproductive harm Wash hands after handling Do not open the battery Battery contains lead acid and other materials that are toxic and corrosive Do not open the charger Exposed wiring and circuitry inside case may cause electric shock Only adults may handle or charge the battery NEVER allow child to handle or charge the battery Battery is heavy and contains lead acid electrolyte Do not drop the battery Permanent damage to the battery could occur or cause serious injury Before charging the battery check for wear or damage to the battery charger its supply cord and the connectors DO NOT charge the battery if any damage to parts has occurred Do not allow the battery to drain completely Recharge the battery after each use or once a month if not used regularly Do not charge battery upside down Always secure the battery with the bracket Battery can fall out and injure a child if vehicle tips over The charging input socket is at the right side of the spare wheel The POWER SWITCH must be turned in OFF position when charging Before the first use you should charge the battery for 4 6 hours Do not recharge the battery for more than 10 hours to avoid overheating the charger When the vehicle begins to run slow
5. CHILDREN S ELECTRIC TOY CAR With remote control function nyt NODD V SN lt n ETAL YS J ee f Tey KRA N v E A p all i Al NINY 4 f A A i Products features may vary V from the picture above e Suitable for 37 96 Months e Maximum user weight 30kg e Adult assembly required OWNER S MANUAL with Assembly Instructions Read and understand this entire manual before using Please keep this manual for future reference as it contains important information Before first time use charge the battery for at least 4 6 hours CAUTION WARNING CHOKING HAZARD Small parts Not suitable for children under 36 months Use the vehicle on generally level ground ONLY IMPORTANT 1WD Pi label means the information or assembly for One Wheel Drive version ONLY 2WD label means the information or assembly for Two Wheels Drive version ONLY H L SPEED This label means the information for High Low Speed version ONLY A WARNING FOR THE SAFETY OF YOUR CHILD PLEASE READ ALL WARNINGS AND ASSEMBLY USE INSTRUCTIONS KEEP THIS GUIDE FOR FUTURE REFERENCE e ADULT ASSEMBLY REQUIRED The product contains small parts which are for adult assembly only Keep children away when assembling Always remove protective material and poly bags and dispose before assembly ABOUT YOUR NEW VEHICLE Thank you for your purchasing our products we wants your child to enjoy this product for years to come Kee
6. ONAL MUKO ur E Always stop vehicle when changing the speed or direction to avoid damage the gears and motor Ag on switch Volume knob REE RIC Pedal sE switch NA Jia Power switch Digital voltmeter OPTIONAL BBAVDAAV Tq SOU KY oe 4 peace High speed Drive switch Make sure your child knows how to steer how to start and stop the High Low vehicle and knows the speed rules for safe driving The A switch vehicle can be driven at a Volume knob g RIC Pedaj maximum of 3 5 km h E jS a ia bee switch T Foot pedal pa 4 A B Power switch FORWARD 1 Press the Forward backward switch on the Forward position 2 Press the Foot pedal the vehicle drives forward STOP The vehicle will stop automatically when your child s foot remove from the Foot pedal REVERSE 1 Press the Forward backward switch on the Backward position 2 Press the Foot pedal the vehicle drives backward SOUNDS BUTTON Press the buttons on the dash and rear light bar for sound playing VOLUME KNOB Turn the knob clockwise to increase the volume Turn the knob counterclockwise to decrease the volume HIGH LOW SPEED SWITCH OPTIONAL The switch operates the vehicle to move in low or high speed DIGITAL VOLTMETER OPTIONAL See page 14 l7 Ss HOW TO USE THE REMOTE CONTROLLER ce ADULT OPERATING REQUIRED LEFT JOY STICK RIGHT JOY STICK ON OFF SWITCH
7. SION SWITCH on the vehicle to the Remote control position 2 Press the ON OFF SWITCH on the remote controller to the ON position the indicator light will be lighting 3 Push the LEFT JOY STICK to the front the vehicle goes forward pull the LEFT JOY STICK to the back the vehicle goes backward 4 Push the RIGHT JOY STICK to the left the vehicle turn left push the RIGHT JOY STICK to the right the vehicle turns right CHARGING YOUR VEHICLE ONLY AN ADULT CAN CHARGE AND RECHARGE THE BATTERY WARNING e PREVENT FIRE AND ELECTRIC SHOCK Use the only rechargeable battery and charger supplied with your vehicle NEVER substitute the battery or the charger with another brand Using another battery or charger my cause a fire or explosion Do not use the battery or charger for any other product Overheating fire or explosion could occur NEVER modify the electric circuit system Tampering with the electric system may cause a shock fire or explosion or my permanently damage the system Do not allow direct contact between battery terminals Fire or explosion can occur Do not allow any type of liquid on the battery or its components Explosive gasses are created during charging Do not charge near heat or flammable materials Charge the battery in a well ventilated area ONLY NEVER pick up the battery by the wires or charger Damage can occur to the battery and may cause a fire Pick up the battery by the case
8. c parts on a regular basis for cracks or broken pieces Rules for Safe Riding READ THESE RULES ALOUD TO YOUR CHILD AND THEIR PLAYMATES AND MAKE SURE THEY UNDERSTAND THEM e Keep Children within Safe Riding Areas Never use in roadway near motor vehicles on lawn space on or near steep inclines or steps swimming pools or other bodies of water e Use the toy only on flat surfaces Such as inside your house garden or playground e Never use in the dark A child could encounter unexpected obstacles and have an accident Operate the vehicle only in the daytime or a well lit area t is not recommended to drive the vehicle on wet surfaces or on lopes of greater than 15 degrees e Do not use this vehicle outdoors when it is raining or snowing e Make sure you come to a complete stop before changing directions from forward to back e Please follow the correct weight and age limits allowed to drive this vehicle It is prohibited to change the circuit or add other electric parts Inspect wires and connections of the vehicle periodically In order to avoid accidents please ensure the vehicle is safe before riding e Do not let any child touch the wheels or be near them when the car is moving e This vehicle has adjustable play seat belts Please instruct children how to tie the safety belt before using guarantee the security HOW TO OPERATE YOUR VEHICLE Use OperationA _ Sound buttons Audio input Digital voltmeter OPTI
9. e wheel cover of spare wheel e Turn the vehicle body upright 4x12 round e Fit the tabs on the windshield into the Slots in the vehicle e Insert two 4x12 round head screws and tighten with a screwdriver head screws 1 ASSEMBLY STEPS Q5 nut machine screw End of steering column Motor connector Power connector ji f f i l j j j j j j e Remove the M5x35 machine screw and 5 nut from the steering wheel e Insert the steering wheel to the end of the steering column e Insert the M5x35 machine screw through the steering wheel and steering column and tighten the 5 nut back in the same location e Plug the power connector into the terminal on battery as shown e Plug the vehicle connector s into the motor connector s e Fit the motor hood on the motor EP e Tighten four 04x12 flat head screws to secure it ASSEMBLY STEPS e Insert the tabs at the back of the seat into the slots in the vehicle body e Insert two M5x16 machine screws and tighten with a screwdriver e Insert the view mirror into the hole in the vehicle body and push until you hear this click into place e Repeat for the other side IMPORTANT SUPPLEMENT TO INSTRUCTION MANUAL After assembling any wheel to the axles please check the gap between the screw thread and the collapsible refer to below picture if the gap is too big please add two or three washers inside
10. hicle indoors or cover it with a tarp to protect it from wet weather Keep the vehicle away from sources of heat such as stoves and heaters Plastic parts may melt Recharge the battery after each use Only an adult can handle the battery Recharge the battery at least once a month when the vehicle Raider is not being used Do not wash the vehicle with a hose Do not wash the vehicle with soap and water Do not drive the vehicle in rainy or snowy weather Water will damage the motor electric system and battery Clean the vehicle with a soft dry cloth To restore shine to plastic parts use a non wax furniture polish Do not use car wax Do not use abrasive cleaners Do not drive the vehicle in loose dirt sand or fine gravel which could damage moving parts motors or the electric system When not using all the electrical source should be turn off Turn off the power switch and disconnect the battery connection DISPOSAL OF BATTERY OY Disposal Of Battery lt amp amp A e Your sealed lead acid battery must be recycled or disposed of in an environmentally sound manner e Do not dispose of your lead acid battery in a fire The battery may explode or leak e Do not dispose of a lead acid battery in your regular household trash The incineration land filling or mixing of sealed lead acid batteries with household trash is prohibited by law e Return an exhausted battery to your local approved lead acid battery recycle suchasa loca
11. in 10 Washer Spanner 1 pcs FOR SPARE 1 pcs FOR SPARE H L n ES 4 oO oO cc O O haa PARTS DIAGRAM Screwdriver not included Pliers not included Some parts shown are NOTE assembled on both sides of vehicle ASSEMBLY STEPS e Your new vehicle requires adult assembly Please set aside at least 40 minutes for assembly Children can be harmed by small parts sharp edges and sharp points in the vehicle s unassembled state Care should be taken in unpacking and assembly of the vehicle Children should not handle parts or help in assembly of the vehicle Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded e Assembly tool for need screwdriver provide for oneself and spanner 24x12 round e Turn the vehicle body downside up 1 head screws Fit the side support to the vehicle Side support body HINT If the side support does not seem to fit change the other one and try again e Insert six 04x12 round head screws and tighten with a screwdriver e Repeat for the other side e Remove all the parts from the EMD rear axle e Slide a 12 washer onto the rear axle from the longer end Rear axle Insert the rear axle through the hole in vehicle body Rear axle 12 Washer e Remove all the parts from the rear axle e Insert the rear axle
12. l seller of automotive batteries e Contact your local waste management officials for other information regarding the environmentally sound recycling and disposal of lead acid batteries Our products are suitable for ASTM F963 GB6675 EN71 and EN62115 standard
13. ly recharge the battery After each use or once a month minimum recharge time as 8 to 12 hours less than 20 hours at most CHARGING YOUR VEHICLE According the table to decide whether to charge the battery BATTERY MAGNITUDE OF VOLTAGE BATTERY STATE 6V4Ahx1 6V7Ahx1 2 6 6 The battery is full 6V10Ahx1 amon The vehicle can wrok normally STOP operating the vehicle the battery needs to charge 6V7Ahx2 6V10Ahx2 213 2 The battery is full 12V7Ahx1 12V10Ahx1 13 1 12 6 The vehicle can wrok normally STOP operating the vehicle the battery needs to charge 1 Open the cover of the socket the socket is at the right side of the spare wheel 2 Plug the charger port into the input socket 3 Plug the charger plug into a wall outlet The battery will begin charging A WARNING This product with CHARGING PROTECTION When charging all the functions will be cut off TROUBLESHOOTING GUIDE E PROBLEM The vehicle does not run PROBLEM CAUSE The battery may low on power After each use or once a month minimum charge the battery for a full 10 hours Do not leave the battery on the charger for more than 20 hours POSSI BLE CAUSE Thermal fuse has tripped The vehicle is equipped with a self resetting fuse When the vehicle is overloaded or operated incorrectly the self resetting fuse will be cut off for 5 20seconds before becoming operational again The self resetting fuse is under the seat Refer to the picture
14. p these points in mind as you read this guide Battery amp 6V7AH x1 Fuse 10A 6V10AH x1 Fuse 10A Fuse ATD 6V7AH x2 Fuse 5A and 13A 12V7AH x1 Fuse 5A and 13A Load Capacity Under 30KGS Size of car 125 x 70 x 52 CM Suitable age 96 months D3KW H 3 5KM H Average Avvoroximatel i Input depend on local voltage aai life PP y Charger Output DC 6V500mA or DC6V1A J u 300 times or DC12V1A Charge time 8 12 Hours Charging type VER SMS JE128 EN RC 121105 PARTS LIST PART NO PART NAME Q ty pcs Vehicle body Gear box J x x m e BE g lt L eN Driving wheel lt L N Normal wheel a ais g lt L UJ lt L N Bushing a g lt L UJ 3 NO Motor hood a g lt lt L N QA4x12 flat head screw a BB g xX X oo gt 12 washer 10 locknut M5x16 machine screw Side support Steering column Rear axle Windshield View mirror Steering wheel M5x35 machine screw 5 nut Spare wheel Seat Charger M5x20machine screw R C driver Remote controller REMARKS 1 pcs labeled R 1 pcs labeled 2 pcs placed on the front axle 1 pcs placed on the rear axle Placed on the front axle Placed on the steering whee Placed on the vehicle body Placed on the steering wheel 1 pcs placed on the steering wheel 1 pcs placed on the steering colum 4x12 round head screw 4x16 screw Hubcap Split p
15. the wheel But after tightening the nut outside the wheel please turn the wheel by your finger to check if the wheel can run smoothly this is very important because if the wheel can run smoothly it is ok but if the nut press the wheel and the wheel can t run smoothly the motor will be broken easily Then you need to decrease one or two washers to make sure the wheel can run smoothly HOW TO OPERATE YOUR VEHICLE A WARNING PREVENT INJURIES AND DEATHS e NEVER LEAVE CHILD UNATTENDED DIRECT ADULT SUPERVISION IS REQUIRED Always keep child in view when child is in vehicle e This toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties Protective equipment should be worn e Never use in roadways near cars on or near steep inclines or steps swimming pools or other bodies of water e Always wear shoes e Always sit on the seat e Not to be used in traffic e This toy is unsuitable for children under 37 months due to its maximum speed Maximum user weight is 30 kgs This toy has no brake Must confirm before using that following work which is already finished Important Before using the vehicle for the first time the battery needs to be charged for 4 to 6 hours no more than 10 hours Only an adult can charge and recharge the battery e Check all the screws cap nuts and protective coverings regularly and tighten as required Check plasti
16. through the hole in the vehicle body ASSEMBLY STEPS _ ft Driving wheel Normal wheel g Fit the gear box onto the rear 1WD axle from the left side Standing at the rear of the vehicle body And make the motor on the gear box pass through the hole in the vehicle body Gear box Fit the driving wheel onto the rear axle keep it match with the gear box e Fit a O12 washer onto the rear axle e Fit a O10 locknut to the end of the Driving wheel rear axle Locknut Rear axle Slide the gear box standing at back of vehicle body onto the rear axle R labeled gear box should be fit to the R side of vehicle body L labeled gear box should be fit to L side of vehicle body Slide the driving wheel onto rear axle make it match with the gear box Slide a O12 washer Tighten the 10 locknut with a spanner Do not over tighten Repeat this procedure to assemble the other driving wheel to the rear axle Alp Hint An extra spanner has been provided to hold the 10 locknut on the other side of the front axle while tightening the locknut on the other side ee e Remove the parts from the front axle 4 mae Washer Y e Fit a 212 washer onto the axle ga Fit a bushing onto the axle e Fit a normal wheel onto the axle make the wheel match with the bushing e Fit a G12 washer onto the axle e Tighten the 010 locknut with a spanner Do not over
17. tighten Bushing Fonade e Repeat for the other wheel s Washer ASSEMBLY STEPS e Snap a hubcap onto the center of each wheel cover Hubcaps ee ir S BOTTOM VIEW Split pin Direction al A gear box mA SA R C driver column Split pin washer Steering column e Turn the vehicle body on its side e Remove the screw and nut from the R C driver with a screwdriver e Insert the straight end of steering column up through the hole in the R C driver the hole in the direction gear box and the hole in the vehicle body Continue pushing the steering column to pass through the hole in the dash e Line up the holes in the R C driver with the hole in the steering column tighten the M5x20 machine screw and 5 nut back in the same location with a screwdriver PIC 6 1 e Insert the bent end of steering column through the hole in the front axle linkage insert a 810 washer onto the steering column and insert a split pin into the hole in the steering shaft bend the ends of split pin back using a pair of pliers PIC 6 2 ASSEMBLY STEPS 7 Slots in the vehicle body BOTTOM VIEW Il 4x16 round head screws REAR VIEW 7 e Insert the tabs in the spare wheel into the slots at the rear of the vehicle body Spare wheel e Insert two 4x16 round head screws through the vehicle body wall and into the spare wheel tighten with a screwdriver e Snap the hubcap into th
Download Pdf Manuals
Related Search