LED LED 60W Scanner Light - Flash
Contents
1. 4 The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices in hanging installations may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the2. amp Sound Active Built in lighting programs Sound Active Compact amp portable design Manual focusing lens Gobo Shake effect Strobe effect in every color 13 degree beam angle DMX 512 protocol Fan cooled Hanging Bracket Included Optional controller easy to use JC 6 controller sold separately e Advantages of LED technology extremely long life low power consumption minimal heat emission defacto maintenance free with brilliant light radiation Overview 1 Mirror 2 Objective lens Focus 3 Mounting bracket 4 Fixation screw 5 Housing cover 6 Remote Control socket 7 DMX In socket 8 DMX Out socket 9 Power supply Fuseholder 10 Control Board 11 Down button 12 Up button 13 Menu button 14 Microphone 15 Rotary control microphone sensitivity INSTALLATION Overhead rigging The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden www flash butrym pl Page
3. device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s DANGER OF FIRE weight When installing the device make sure there is no highly inflammablematerial decoration articles etc within a distance of min 0 5 m Mount the device to your trussing system using an appropriate clamp For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick link with screw cap Pull the safety rope through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope which already held the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws DANGER TO LIFE ANS taking into operation for the first time the installation has to be approved by an expert Master Slave operation The master slave operation enables that several devices can be synchronized and controlled by one master device On the rear panel of the LED 60W Scan you canfind an XLR jack DMX Out and an XLR plug DMX In which can be used for connecting several devices Choose the device which is to control the effects This device then works as master device and controls all other slave devices
4. otherwise the fixtures will not work at all or will not work properly N Please note the starting address depends upon which controller is being used N Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 Q resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture Connection with the mains Connect the device to the mains with the enclosed power supply cable The occupation of the connection cables is as follows international Yellow Green The earth has to be connected If the device will be directly connected with the loc
5. USER MANUAL LED 60W Scanner Light www flash butrvm nl Page 1 SS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Please make sure that there are no obvious transport damages Should you notice any damages on the A C connection cable or on the casing do not take the device into operation and immediately consult your local dealer This device falls under protection class The power plug must only be plugged into a protection class outlet The voltage and frequency must exactly be the same as stated on the device Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Never touch them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the powe
6. al power supply network a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation The device must only be connected with an electric installation carried out in compliance with the IEC standards The electric installation must be equipped with a Residual Current Device RCD with a maximum fault current of 30 mA Lighting effects must not be connected to dimming packs www flash butrym pl Page 7 OPERATION After you connected the effect to the mains the LED 60W Scan starts running During the Reset the motors are trimmed and the device is ready for use afterwards Stand Alone operation In the Stand Alone mode the LED 60W Scan can be used without controller You can do without a controller as the LED 60W Scan features a built in microphone which provides automatic sound control Disconnect the LED 60W Scan from the controller and select the desired Master Mode Master Slave operation Connect the master and slave devices and adjust the settings as desribed above DMX controlled operation You can control the projectors individually via your DMX controller Every DMX channel has a different occupation with different features Addressing The Control Board allows you to assign the DMX fixture address which is defined as the first channel from which the LED 60W Scan will respond to the controller Please be sure that you don t have any overlapping c
7. en choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others This device must never be operated or stockpiled in sourroundings where splash water rain moisture or fog may harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0 5 meters between smoke machine and device The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters The ambient temperature must always be between 5 C and 45 C Keep away from direct insulation particularly in cars and heaters The relative humidity must not exceed 50 with an ambient temperature of 45 C This device must only be operated in an altitude between 20 and 2000 m over NN Never use the device during thunderstorms Over voltage could destroy the device Always disconnect the device during thunderstorms The symbol q di mE determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 1 meters This device is only allowed for an installation via the mounting bracket In order to safeguard sufficient ventilation leave 50 cm of free space a
8. es or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE AN seconnee from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents CAUTION ne lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly www flash butrym pl Page 10 To ensure a proper function of the rotating parts we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out during the rotation There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized deale
9. hannels in order to control each LED 60W Scan correctly and independently from any other fixture on the DMX data link If two three or more LED 60W Scan are addressed similarly they will work similarly For address setting press the Mode button until the display shows A 001 and set the desired address via the Up Down buttons Controlling After having addressed all LED 60W Scan you may now start operating these via your lighting controller Note After switching on the LED 60W Scan will automati cally detect whether DMX 512 data is received or not lf the data is received the display will show A 001 with the actually set address If there is no datareceived at the DMX input the display will show A001 This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the LED 60W Scan the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link DMX protocol Control channel 1 Horizontal movement Pan Push slider up in order to move the mirror horizontally PAN Gradual mirror adjustment from one end of the slider to the other 0 255 128 center The mirror can be stopped at any position you wish Control channel 2 Vertical move
10. ment Tilt Push slider up in order to move the mirror vertically TILT Gradual mirror adjustment from one end of the slider to the other 0 255 128 center The mirror can be stopped at any position you wish www flash butrym pl Page 8 Control channel 3 COLORS a WHITE 80 9 LUIGHTBLUE _ _ _ _ _ m GREEN y Control channel 4 Gobo rotation wheel ON 8 1 SpinGobot 80 87 GOBO 2 SHAKE __96 103 GOBO 4 SHAKE Control channel 5 Gobo rotation 0 15 Norotaton S Forwards gobo rotation with decreasing speed Backwards gobo rotation with increasing speed Control channel 6 SHUTTER STROBE Oo 7 BLACKOUT Cs 8 15 SHUTTEROPEN Cd SHUTTER OPEN po SHUTTER OPEN Control channel 7 DIMMER O 255 DIMMER 0 100 Control channel 8 MOVING HEAD MOVEMENT www flash butrym pl Page 9 Feature 1 Control channel 9 MOVEMENT SPEED O0 255 MOVEMENT SPEED SLOW FAST oO e e0 T h OI NIOIAIN CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devic
11. r cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficientcable to the device Otherwise the cable may be damaged which may lead to mortal damage Make sure that the power cord is never crimped or damaged by sharp edges Check the device and thepower cord from time to time lf extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damaged leading to mortal electrical shock If the power plug or the power switch is not accessible the device must be disconnected via the mains If the power plug or the device is dusty the device must be taken out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to mortal electrical shock More severe dirt in and at the device should only be removed by a specialist There must never enter any liquid into power outlets extension cords or any holes in the housing of the device If you suppose that also a minimal amount of liq
12. round the device The housing must never touch surrounding surfaces or objects Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope The maximum ambient temperature T 45 C must never be exceeded Operate the device only after having become familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Never use solvents or aggressive detergents in order to clean the device Rather use a soft and damp cloth Please use the original packaging if the device is to be transported Make sure that you pack the device in the Original state Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may sufferdamages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock crash etc www flash butrym pl Page 3 DESCRIPTION OF THE DEVICE Features LED version of the scanner High performance mobile DMX scanner with 1 x 60W LED source 7 Colors White Gobo wheel with 7 rotating gobos and open 9 DMX Channels 3 Button menu system LED Display making it easy to navigate 3 Operational modes DMX controller Master Slave
13. rs Replacing the fuse If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Open the fuseholder on the rearpanel with a fitting screwdriver Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by a special power supply cable available at your dealer Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS Power supply 230 V AC 50 Hz Power consumption 90 W DMX control channels Qo pin XLR DMX 512 connection 3 pin XLR Sound control microphone Flash rate Number of LEDs Dimensions LxWxH Weight Maximum ambient temperature Ta Maximum housing temperature TB steady state Min distance from flammable surfaces Min distance to lighted object Fuse F 2 A 250 V Please note Every information is subject to change without prior notice 12 8 2009 www flash butrym pl Page 11
14. uid may have entered the device it must immediately be disconnected This is also valid if the device was exposed to high humidity Also if the device is still running the device must be checked by a specialist if the liquid has reduced any insulation Reduced insulation can cause mortal electrical shock There must never be any objects entering into the device This is especially valid for metal parts If any metal parts like staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal parts may cause mortal injuries HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs www flash butrym pl Page 2 Never leave this device running unattended OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects This product is only allowed to be operated with an alternating voltage of 230 V 50 Hz and was designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device Wh
15. which are to be connected to the master device via a balanced microphone lead Connect the DMX OUT jack with the DMX IN plug of the next device www flash butrym pl Page 5 DMX Mode ADHD Control Board Slave Mode G UP MENU Master Mode g HDown PAN Mode Bai D O g MENU UP DOWN Tilt Mode E 0 LED Display d Set the desired Master mode for the master device Set the respective Slave mode for all slave devices Please note The function G 3 is only meant for service purposes Please do only use this function if you want to set the unit shortly into standby mode Pan Reverse With this function you can reverse the Pan movement Tilt Reverse E L With this function you can reverse the Tilt movement Display close time d With this function you can shut off the LED display Remote Control socket If you wish to lock the light output via an optional JC 6 remote control connect your JC 6 remote control to the remote control socket The optional JC 6 Controller not included may be used to con trol different functions including blackout MODE Red LED Green LED Button 1 Button 2 a Se ee Sound Mode On Rx Select Gobo __ Select Color DMX 512 connection connection between fixtures 120 Ohms LS DMX 512 Contro www flash butrym pl Page 6 A wires must not come into contact with each other
Download Pdf Manuals
Related Search