LED-707 User Manual
Contents
1. LED 07 orano ALONS TABLE OF CONTENTS 1 Safety Instructions 2 Technical Specifications 3 Installation 4 How to control the fixture 5 DMX512 Configuration 6 DMX512 Connections 7 Troubleshooting 8 Fixture Cleaning User Manual Please read the instructions carefully before use WARNING 1 Safety Introductions A N Please read the instructions carefully which includes important information about the installation operation and maintenance Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the fixture Before operating ensure that the voltage and frequency of power supply match the power requirements of the fixture It s important to ground the yellow green conductor to earth in order to avoid electric shock Disconnect main power before servicing and maintenance Use safety chain when fixes this fixture Don t handle the fixture by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistan2. 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 8A 8 Fixture Cleanino The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements Innovation Quality Performance 9A
3. controller The address number is between 0 511 usually O amp 1 are equal to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 6A 7A 7 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light and the fan does not work 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some fixtures don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the fixture Set the proper address D No response to the sound 1 Make sure the fixture does not receive DMX signal
4. 120 129 Chase 12 Pattern 11 110 119 Chase 11 Ae Termination reduces signal errors and to avoid signal 9 Pattern 10 100 109 Chase 10 transmission problems and interference It is always Batter 09 090 Chase 00 advisable to connect a DMX terminal Pattern 08 080 089 Chase 08 a Se a Pattern 07 070 079 Chase 07 Resistance 120 ohm 1 4W between pin2 DMX and Pattern 06 060 069 Chase 06 Slow pin3 DMX of the last fixture Pattern 05 050 059 Chase 05 Strobe l l l l Pattern 04 040 049 Chase 04 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the ine 039 Pattern 03 030 039 Chase 03 er Pattern Pattern 02 020 029 Chase 02 fixture to the input of the next fixture The cable cannot be branched or split to a Y Pattern 01 010 019 Chase 01 Blackout bie inad t d d bi id d ion ded t Blackout 000 009 Blackout 0 0 cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit when no power is connected to the fixture 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the
5. ce center Always use the same type spare parts Do not connect the device to any dimmer pack Do not touch any wire during operation and there might be a hazard of electric shock To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture The housing must be replaced if they are visibly damaged Do not look directly at the LED light beam while the fixture is on There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer 2A 2 technical Specifications Power supply Input Voltage AC 100V 240V 50 60Hz 4 Channels Channel 1 Mode Channel 2 Pattern Chase Channel 3 Pattern Strobe Chase Speed Channel 4 Dimmer It can be operated by DMX512 control or can be used as an individual unit without controller It can be linked together as many as required in master slave mode and perform the great built in programmed lighting shows triggered by music Please use a 3 pin XLR cable plug when connecting them together lt features different pre programmed chase patterns Fan cooled Dimension 194 x 202 x 141 mm Weight 1KG 3 Installation You can install the unit on the truss or ceiling Use clamps to fix the unit to truss Always ensure that the unit is firmly fixed to avoid vibration and slipping while opera
6. ol the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX A signal Press the MENU button up to when the MDAT is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 units DMX address can be setting remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain 5A 5 DMX512 Configuration 6 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels ELA A ZEE JZE DMX512 Configuration Ch Mode 250 255 Pattern 25 250 255 Chase 25 955 100 240 235 240 249 Pattern 24 240 249 Chase 24 Stand alone 230 239 Pattern 23 230 239 Chase 23 Pattern 22 220 229 Chase 22 Pattern 21 210 219 Chase 21 Pattern 20 200 209 Chase 20 Pattern 19 1980 199 Chase 19 180 189 Pattern 18 180 189 Chase 18 170 179 Pattern 17 170 179 Chase 17 COMMON 160 169 Pattern 16 160 169 Chase 16 120 239 150 159 Pattern 15 150 159 Chase 15 3 140 149 Pattern 14 140 149 Chase 14 Chase 430 139 Pattern 13 130 139 Chase 13 Pattern 12
7. rmal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show i i ii slave mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 4 2 Easy Controller by CA 8 The easy remote control is used only in master slave mode There is a terminator for In oe ite connect the easy controller inside the fixture By connecting the cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the first fixture you will find that the remote control on the first fixture will control all the other fixtures for Stand by Function and Mode functions Blackout Blackout the unit 1 Synchronous Strobe Function 2 Sound Strobe Chase Select Chase 1 10 3 Two light Strobe Sound Strobe Chase LED OFF ese ON 3 4 3 iSolution Operation e Consistent DMX configuration enable iMove to be linked together with iRock and iShow and controlled at the same time DMX address can be set remotely by iLead controller Please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain Automatic switching between DMX function and built in stand alone programs 4 4 DMX Controller An universal DMX controller to contr
8. ting Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 kg for each unit Place on the ground Fixed on the ceiling Clamp on the truss 3A 4 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By iLead controller Please refer to the user guide of iLead or universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 200S on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in master mode Satie and select ah Li show 1 or anc show 2 or ah 3 show 3 or aH H show 4 mode Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode SLIid and select no
Download Pdf Manuals
Related Search