HG755440SM EN User manual
Contents
1. A If you change from natural gas G20 20 mbar to liquid gas fully tighten the by pass screw in If you change from liquid gas to natu ral gas G20 20 mbar undo the by pass screw approximately 1 4 of a turn 1 2 of a turn for Triple Crown burner WARNING Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position 8 5 Electrical connection Do not pull the mains cable to discon nect the appliance Always pull the mains plug The appliance must not be connected with an extension cable an adapter or a multiple socket There is a risk of fire Do not let the power cable to heat up to a temperature of more than 90 C The cable should be guided by means of clamps fixed to the side of the cabi net in order to avoid any contact with the equipment beneath the cooktop Make sure that there is access to the mains plug after the installation ENGLISH 13 Electrical Requirements Permanent electrical installation must agree with the latest I E E Regulations and local Electricity Board regulations For your own safety the installation must be done by a qualified electrician e g your local Electricity Board or a contrac tor who is on the roll of the National In spection Council for Electrical Installa tion Contracting NICEIC The manufacturer refuses to be held responsible if these safe ty measures are not abided by Supply connections This2. are not squeezed Also be careful when the hob is put together with an oven A It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct as sembly will cause leakage of gas A A Make sure that the gas supply pressure of the appliance obeys the recommended values Rigid connection Carry out connection by using metal rig id pipes copper with mechanical end 8 3 Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burner 3 With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use see table in Technical Information chapter 4 Assemble the parts follow the same procedure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package sup plied with the appliance If the supply gas pressure is changeable or different from the necessary pressure you must fit an applicable pressure ad juster on the gas supply pipe 8 4 Adjustment of minimum level To adjust the minimum level of the burn ers 1 2 3 Light the burner Turn the knob on the minimum posi tion Remove the knob With a thin screwdriver adjust the by pass screw position A CY gt no A The by pass screw
3. Environmental information Subject to change without notice ENGLISH 3 1 SAFETY INFORMATION Before the installation and use of the appliance careful ly read the supplied instructions The manufacturer is not responsible if an incorrect installation and use cau ses injuries and damages Always keep the instructions with the appliance for future reference 1 1 Children and vulnerable people safety WARNING Risk of suffocation injury or permanent disability e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised by an adult or a person who is responsible for their safety e Do not let children play with the appliance e Keep all packaging away from children e Keep children and pets away from the appliance when it operates or when it cools down Accessible parts are hot e Ifthe appliance has a child safety device we recom mend that you activate it e Cleaning and user maintenance shall not be made by children without supervision 1 2 General Safety e The appliance and its accessible parts become hot during use Do not touch the heating elements e Do not operate the appliance by means of an exter nal timer or separate remote control system e Unattended cooking on a hob with fat or oil can be dangerous and may result in fire 4 www aeg com e Never try to extinguish a fire
4. hob has to be connected to 230 240 V 50 Hz electricity supply The hob has a terminal block which is marked as follows e L Live terminal e N Neutral terminal e or E Earth terminal Before carrying out the connection make sure 1 The limiter valve and the electrical system can take the appliance load see the rating plate 2 The supply system is equipped with an efficient earth connection in com pliance with the current standards and regulations 3 The outlet or omnipolar switch used for connection is easily accessible with the appliance installed The appliance is supplied with a 3 core flexible powercable with a 3 amp plug If it is necessary to change the fuse use a 3 amp ASTA approved BS 1362 fuse 14 www aeg com A Green and Yellow B 3 amp fuse C Brown D Cord clamp E Blue The wires in the cord are coloured as fol lows Green and yellow Earth Blue Neutral Brown Live letter L lt must always be connec ted to the network phase There must be no cut or stray strands of wire present The cord clamp must be correctly attached to the outer sheath i To replace the connection cable use only HO5V2V2 F T90 or equivalent type Make sure that the cable section is applicable to the voltage load and the working temperature The yellow green earth wire B must be approxi mately 2 cm longer than the live and neutral wire A
5. the bottom Electrical connection WARNING Risk of fire and electrical shock e All electrical connections must be made by a qualified electrician The appliance must be earthed e Before carrying out any operation make sure that the appliance is dis connected from the power supply e Use the correct electricity mains cable e Do not let the electricity mains cable tangle e Make sure the mains cable or plug if applicable does not touch the hot ap pliance or hot cookware when you connect the appliance to the near sockets e Make sure the appliance is installed correctly Loose and incorrect electrici ty mains cable or plug if applicable can make the terminal become too hot e Make sure that a shock protection is installed e Use the strain relief clamp on cable e Make sure not to cause damage to the mains plug if applicable or to the mains cable Contact the Service or an electrician to change a damaged mains cable e The electrical installation must have an isolation device which lets you discon nect the appliance from the mains at all poles The isolation device must have a contact opening width of mini mum 3 mm e Use only correct isolation devices line protecting cut outs fuses screw type fuses removed from the holder earth leakage trips and contactors Gas connection e All gas connections should be made by a qualified person e Make sure that there is air circulation
6. D NO 230V 50Hz PROD NO PROD NO C 0049 SER NO 1P20 SER NO SER NO as tr DATA DATA MADE IN ITALY I J I I I I I I I 1 MODEL MODEL 1 W HE I Stick it on instruction booklet Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m8 If it is installed in a room of vol ume less than 5 m an air vent of effec tive area of 100 cm is required If it is in stalled in a room of volume between 5 m3 and 10 m an air vent of effective area of 50 cm is required while if the volume exceeds 11 m no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is be tween 5 m3 and 11 m3 If there are other fuel burning appliances in the same room B S 5440 Part 2 Cur rent Edition should be consulted to de termine the requisite air vent require ments For appliances installed in the Republic of Ireland please refer to the NSAI Do mestic Gas Installation 1 S 813 Current Editions Table Four 12 www aeg com Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater than 20 m3 but not in a bathroom or shower room The minimum distance combustible ma terial can be fitted above the hob in line with the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be
7. Kitchen unit with door The panel installed below the hob must be easy to remove and let an easy ac cess in case a technical assistance inter vention is necessary IK mm n f frin 20 mm d max 150 mm a Removable pane 9 TECHNICAL INFORMATION Hob dimensions Length 480 mm Width 744mm Heat input Bengt 510 mm Triple Crown 40kW burner Hob recess dimensions Width 560 mm Rapid burner 3 0 kW 16 www aeg com Semi rapid burn 2 0 kW Category 112H3 A Gas connection G 1 2 Auxiliary burner 1 0 kw een G20 2H 20 mbar TOTAL POWER G20 2H 20mbar a ee ee 12 KW ppliance class on By pass diameters G31 3 37 mbar Burner By pass in 843 g h 1 100 mm Electric supply 230 V 50 Hz Auxiliary 28 3 core flexible cable with non Semi rapid 32 rewirable plug Rapid 42 fitted with a 3 a a Triple Crown 56 amp cartridge fuse Gas burners NORMAL POWER NOR RE MAL DUCED NATURAL GAS LPG Butane Propane POWER POWER G20 2H 20 G30 G31 3 28 30 37 BURN mbar mbar ER En ee G30 G31 inj in 28 30 37 kw kW 1 100 m h 1 100 mbar mbar mm mm g h g h AN 1 0 0 33 70 0 095 50 73 71 Semi 2 0 0 45 96 0 190 71 145 143 rapid 3 0 natu Rapid ral gas 0 75 119 0 286 86 204 200 2 8 LPG as 40 1 4 146 0 381 98 291 286 rown 10 ENVIRONMENT CONCERNS Recycle the materials with the appliances Do not dispose symbol amp Put t
8. O O HG755440SM EN User manual OO WAEG perfekt in form und funktion 2 www aeg com CONTENTS 1 SAFETY INFORMATION ccoo nassen een Ba Wee ra 3 2 SAFETY INSTRUCTIONS 2 222 482 a em 4 3 PRODUCT DESCRIPTION terere errores dada 6 As DAILY USE jib deh dia dd dades ab ee 6 5 HELPEUL AINTS AND TIPS as an ba 8 6 CAREAND CLEANING I ic 5 aig e ae a ee ee 8 Tx TROUBLESHOOTING o es ts arena we tad Ra eet 10 8 INSTALLATION og cia mt ound an e ety hand Gees Eee ee ee ed oe 11 9 TECHNICAL INFORMATION ans sans se een 15 FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it Visit our website for Get usage advice brochures trouble shooter service information www aeg com Register your product for better service www aeg com productregistration Buy Accessories Consumables and Original spare parts for your appliance www aeg com shop ad amp CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Serial Number A Warning Caution Safety information i General information and tips 9
9. UCT DESCRIPTION 3 1 Cooking surface layout mo 00000 e Contact your municipal authority for information on how to discard the ap pliance correctly e Disconnect the appliance from the mains supply e Cut off the mains cable and discard it e Flat the external gas pipes Semi rapid burner Triple Crown burner Rapid burner Auxiliary burner Control knobs 3 2 Control knobs Symbol Description no gas supply off position ignition posi tion maximum gas supply 4 DAILY USE WARNING Refer to the Safety chapters Symbol Description minimum gas supply 4 1 Ignition of the burner IN WARNING Be very careful when you use open fire in kitchen environment Manufacturer decline any re sponsibility in case misuse of the flame i Always light the burner before you put cookware To light the burner 1 Turn the control knob counterclock wise to the maximum position 2X and push it down 2 Keep the control knob pushed for approximately 5 seconds this will let thermocouple to warm up If not the gas supply will be interrupted Adjust the flame after it is regular i If after some tries the burner does not light check if the crown and its cap are in correct posi tions w i Each control knob has a pilot light It lights up when you turn the control knob ENGLISH 7 A Burner cap B Burner crown C Ignition ca
10. WARNING A Replacement of the connection cable 1 Connect the green and yellow earth wire to the terminal which is marked with the letter E or the earth symbol O or coloured green and yellow 2 Connect the blue neutral wire to the terminal which is marked with the letter N or coloured blue 3 Connect the brown live wire to the terminal which is marked with the 8 6 Building In A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competen cies in accordance with the cur rent regulations A min 600 mm min 450 mm min 650 mm ENGLISH 15 b Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continu ous supply of air The electrical connec tion of the hob and the oven must be in stalled separately for safety reasons and to let easy remove oven from the unit A supplied seal _ S AA A A B supplied brackets gt gt Boom gt o om CAUTION 4 i h b Install the appliance only on a worktop with flat surface 4 N a ihiliti i i x 8 7 Possibilities for insertion le om o
11. allowed from the edges of the hob For appliances installed in the Republic of Ireland please refer to NSAI Domes tic Gas Installation I S 813 Current Edi tion Section 7 Permitted Locations of Appliance 8 2 Gas Connection WARNING Any gas installation must be car ried out by a GAS SAFE REGIS TER installer Make sure that once the hob is instal led it is easily accessible for the engi neer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorpora ted in this instruction booklet be ignor ed On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted be tween the components as shown in the diagram Screw the parts together with out using excessive force O A End of shaft with nut B Washer C Elbow Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or copper The connection should be suitable for connecting to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and instal lation Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards Be careful they do not come in touch with mobile parts or they
12. around the appliance e The information about the gas supply is on the rating plate e This appliance is not connected to a device which evacuates the products of combustion Make sure to connect the appliance according to current in stallation regulations Pay attention to requirements regarding adequate ventilation 2 2 Use WARNING Risk of injury burns or electric shock e Use this appliance in a household en vironment e Do not change the specification of this appliance e Do not let the appliance stay unatten ded during operation e Do not operate the appliance with wet hands or when it has contact with wa ter e Do not put cutlery or saucepan lids on the cooking zones They become hot e Set the cooking zone to off after use e Do not use the appliance as a work or as a storage surface WARNING Risk of fire or explosion e Fats and oil when heated can release flammable vapours Keep flames or heated objects away from fats and oils when you cook with them ENGLISH 5 The vapours that very hot oil releases can cause spontaneous combustion e Used oil that can contain food rem nants can cause fire at a lower tem perature than oil used for the first time e Do not put flammable products or items that are wet with flammable products in near or on the appliance WARNING Risk of damage to the appliance e Do not keep hot cookware on the con trol panel e Do not let cookwa
13. elp you quickly and correctly These data are available on the supplied rating plate Model description blocked with food resi jector is not blocked and the burner crown is clear of food parti cles e Product number PNC e Serial Number S N Use the original spare parts only They are available at Service Force Centre and approved spare parts shops 7 1 Labels supplied with the accessories bag Stick the adhesive labels as indicated below MOD ENGLISH 11 WH Stick it on Guarantee Card and send this part Stick it on Guarantee Card and keep this part 8 INSTALLATION WARNING Refer to the Safety chapters A AN WARNING The following instructions about installation connection and maintenance must be carried out by qualified personnel in compli ance with standards and local regulations in force 8 1 Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regulations Current Edition and the IEE Wiring Regulations Current Edition For appliances installed in the Republic of Ireland please refer to NSAI Domes tic Gas Installation S 813 Current Edi tions and the ETCI Rules for Electrical In stallations Provision for ventilation Detailed recommendations are con tained in the following British Standards MOD TYPE PRO
14. en dry them with a soft cloth e The pan supports are not dishwasher proof They must be washed by hand e When you wash the pan supports by hand take care when you dry them as the enamelling process occasionally leaves rough edges If necessary re move stubborn stains using a paste cleaner e Make sure you position the pan sup ports correctly after cleaning e To make the burners work correctly make sure that the arms of the pan supports are in the centre of the burn A ENGLISH 9 e Be very careful when you replace the pan supports to prevent the hob top from damage After cleaning dry the appliance with a soft cloth Removing the dirt 1 Remove immediately melting plastic plastic foil and food con taining sugar Stop the appliance and let it cool down before you clean lime scale rings water rings fat stains shiny metallic discolorations Use a special cleaner for glass or stain less steel 2 Clean the appliance with a damp cloth and some detergent 3 Atthe end rub the appliance dry with a clean cloth The stainless steel can become tarnished if it is too much heated Refer to this you must not cook with potstones earthen ware pans or cast iron plates 6 1 Cleaning of the spark plug This feature is obtained through a ce ramic ignition candle with a metal elec trode Keep these components well c
15. he packaging in appliances marked with the symbol 2 applicable containers to recycle it with the household waste Return the Help protect the environment and product to your local recycling human health and to recycle waste facility or contact your municipal of electrical and electronic office ENGLISH 17 18 www aeg com ENGLISH 19 www aeg com shop P Ce es I 397202002 A 492012 C m HAEG perfekt in form und funktion
16. lean to prevent difficult lighting and check that the burner crown holes are not obstructed 6 2 Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure ad juster if fitted 10 www aeg com 7 TROUBLESHOOTING Problem Possible cause Remedy There is no spark when There is no electrical Make sure that the lighting the gas supply unit is connected and the electrical supply is switched on e Control the fuse If the fuse is released more than one time refer to a qualified electrician e Burner cap and crown Make sure that the are placed uneven burner cap and crown are in correct posi tions The flame is blow out im e Thermocouple isnot After lightning the mediately after ignition heated sufficient flame keep the knob pushed for approxi mately 5 seconds The gas ring burns un e Burner crown is e Make sure that the in evenly dues If there is a fault first try to find a solu tion to the problem yourself If you can not find a solution to the problem your self speak your dealer or the local Serv ice Force Centre i If you operated the appliance in correctly or the installation was not carried out by a registered engineer the visit from the cus tomer service technician or deal er may not take place free of charge even during the warranty period These data are necessary to h
17. ndle D Thermocouple A i WARNING Do not keep the control knob pushed for more than 15 sec onds If the burner does not light after 15 seconds release the control knob turn it into off position and try to light the burner again after minimum 1 minute In the absence of electricity you can ignite the burner without electrical device in this case ap proach the burner with a flame push the relevant knob down and turn it counter clockwise to maximum gas release position If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 mi nute The spark generator can start au tomatically when you switch on the mains after installation or a power cut It is normal 4 2 Turning the burner off To put the flame out turn the knob to the symbol O A WARNING Always turn the flame down or switch it off before you remove the pans from the burner www aeg com 4 3 Using the Wok Stand A wok stand lets you to use a rounded bottom wok on the hob Do not use the wok stand with any other type of wok or pan You must only use the wok stand on the Triple Crown When you install the wok stand make sure that the recesses in the frame fit on the bars of the pan supports 5 HELPFUL HINTS AND TIPS WARNING Refer to the Safety chapters 5 1 Energy savings e f possible always put the lids on the pans e When the liquid starts to boil
18. re to boil dry e Do not activate the cooking zones with empty cookware or without cook ware e Do not put aluminium foil on the ap pliance e Do not let acid liquids for example vinegar lemon juice or limescale re mover touch the hob This can cause matt patches e Provide good ventilation in the room where the appliance is installed e Make sure that the ventilation open ings are not blocked e Use only stable cookware with the cor rect shape and diameter larger than the dimensions of the burners There is a risk of overheating and rupture of the glass plate if applicable e Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum posi tion e Make sure pots are centrally posi tioned on the rings and do not stick out over edges of the cooking surface e Use only the accessories supplied with the appliance e Do not install a flame diffuser on the burner 2 3 Care and Cleaning WARNING Risk of damage to the appliance e Clean regularly the appliance to pre vent the deterioration of the surface material 6 Wwww aeg com e Do not use water spray and steam to clean the appliance e Do not clean the burners in the dish washer e Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal ob jects 2 4 Disposal WARNING Risk of injury or suffocation 3 PROD
19. turn down the flame to barely simmer the liquid Use cookware with diameters applicable to the size of burners Burner Diameters of cook ware Triple 180 260 mm Crown Rapid 180 260 mm Front semi 120 180 mm rapid Rear semi 120 220 mm rapid Auxiliary 80 180 mm WARNING Make sure that the bottoms of pots do not stand above the con trol knobs If the control knobs are under the bottoms of pots the flame heats them up Do not put the same pan on two burners A 6 CARE AND CLEANING WARNING Refer to the Safety chapters T WARNING Make sure that pot handles is not above the front edge of the cooktop Make sure that pots are centrally put on the rings in order to get maximum stability and to get lower gas consumption A Do not put unstable or damaged pots on the rings to prevent from spill and in jury WARNING Do not use a flame diffuser WARNING Deactivate the appliance and let it cool down before you clean it Disconnect the appliance from the electrical supply before you do cleaning or maintenance work Scratches or dark stains on the surface have no effect on how the appliance operates i e You can remove the pan supports to easily clean the hob e To clean the enamelled parts cap and crown wash them with warm soapy water and dry them carefully before you put them back e Wash stainless steel parts with water and th
20. with water but switch off the appliance and then cover flame e g with a lid or a fire blanket e Do not store items on the cooking surfaces e Do not use a steam cleaner to clean the appliance e Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot 2 SAFETY INSTRUCTIONS This appliance is suitable for the following markets IE GB 2 1 Installation WARNING Only a qualified person must in stall this appliance e Remove all the packaging e Do not install or use a damaged appli ance e Obey the installation instruction sup plied with the appliance e Keep the minimum distance from the other appliances and units e Always be careful when you move the appliance because it is heavy Always wear safety gloves e Seal the cut surfaces with a sealant to prevent moisture to cause swelling e Protect the bottom of the appliance from steam and moisture e Do not install the appliance adjacent to a door or under a window This pre vents hot cookware to fall from the ap pliance when the door or the window is opened e Ifthe appliance is installed above drawers make sure that the space be tween the bottom of the appliance and the upper drawer is sufficient for air circulation e The bottom of the appliance can get hot We recommend to install a non combustile separation panel under the appliance to prevent access to
Download Pdf Manuals
Related Search