DUAL GAUGE PRO DPB-M USER`S MANUAL
Contents
1. Divort DPB M As of July 2015 No 1 DUAL GAUGE PRO USER S MANUAL Easy Installation Thank you for purchasing this PIVOT product BOOST DIGITAL D p B M Please read this manual carefully and keep it for future reference Designed for MAZDA SKYACTIV D this product is given to ae another user make sure to include this User s Manual Contents Please check the contents of the package Contents WARNING CAUTION 7e 1 Features Pee eee reer errr rere eee eee ee eee ee ee eee eee 1 2 Part Names and Display 2 Connecting The Wires eesssoessesssessesoseooo 2 A JDG i GN S A Pillar Installing The Product 3 Unit Gauge Cable with aes an with ees A Meter Holder Stand Basic Operation 7777 3 Switching The Display errr eee eee eee ee eee eed 4 5 lllumination color settings v7 4 TERS Illumination brightness settings 4 Zip Ties User s Troubleshooting svc 4 S raw Nut Wek Pree coe Connectors Large x 2 Manual P P x2 Small x5 This Book 1 The display will not be proper if the ECU being used is not the standard one or if a sub computer is being used even in compatible car models 2 Cannot be used in combination with other company s products that use Diagnostic Monitoring Connectors 3 For details about using combinations of PIVOT OBD products see here gt http pivotjp com obd a N A WARN l NG Improper use or disregard of these warnings AN CAUTIO N Imprope2. ching The Display Switching The Digital Display Water Temperature Oil Temperature Reading the Display Water Temp Voltage Oil Temp 35 1 C i o0 99 C 100 150 C The first place on the The third place from the Numerical Value below shows minus below shows E Celsius Only Press switch to change the multi digital display in operation Sem bc 35 gt Gbc A eet Display and Reset the Peak Value Real time Display Peak Value Display for 3 Seconds a for 3 Seconds Reset the Peak Value Only the peak value on display will be reset This will return to the Real time Display for the currently displayed mode With no operation 5 Seconds Peak readings are reset when the key is turned OFF For Boost Water Temperature and Oil Temperature the high will be shown and for Voltage the low will be displayed lf you wish to check the loss of voltage upon operation of the starter turn the key to the ON position and after the digital display comes on operate the starter 2 Display the current 3 or Press the 4 Ee Release the switch illumination color setting switch to change after setting is done the color Engine Start e c 1 9 hele Pad Back to normal display with After the meter off hal R ii le m Engine start durin elease the switc Biessiig the sultan cJ after displayed c i White c Blue the current setting Each pre
3. e the power source and connect the power cable to IGN gt See If connect the power cable to IGN Not normally required below If connect the power cable to IGN Not normally required The meter start up and stop is differ in power connection method Normal not using IGN Cable Linked to the ECU Kei using IGN Cable Linked to the key switch Unplug the connector of and cable of OBD Cable and connect Yellow cable of IGN Cable into the connector on cable then connect to IGN cable to IGN of car Do not connect to Acc Notes about using the OBD Connector OBD Cable Diagnostic Monitoring Connector IGN gt fellow a IGN Cable 12V with Key ON E Cut Connector Make sure to grip the distended portions when pulling it out or inserting it A CAUTION If you unable to get a grip on the distended portions In such case pull out the connector Do not pull on the wires when trying to remove the With some car models it by pulling on the end of the zip tie gt connector the wires may May be difficult to get a a ne R lt become disconnected good grip on the connector How to use the Cut Connectors 1 10mm 2 10mm 3 4 5 ae gt NE When crimping please use crimpers or use i gt liers to bend and then Peel off of the vinyl Feel
4. es Normally illuminated when on display and Three step dimming Dial amp Needle White or Blue Switchable Analog Display Digital Display Red Size Unit mm Meter 15 30 265 260 Analog Display Boost 0 200kPa Digital Display Water Temp 35 150 C Voltage 8 18V Oil Temp 35 150 C 50 Depth22 7 Meter connector Connect gauge 8 Power connector cable Connect OBD cable 9 10 Spare No need to use 7 amp 9 10 Connecting The Wires Engine Start Engine ao Insert the OBD Connector to the Diagnostic Monitoring Start Pigg Connector Raced FRR N fe e Insert the 4 pin Connector to the backside of the meter meter Diagnostic N i Insert the 5 pin Connector of Gauge Cable and 6 pin is monorng D Connector from the Power Cable to the Unit 4 pin se Connector 8 _4 Placement Diagram for Diagnostic Meter Monitoring Connector Holder OV 3 MAZDA D At the right foot of the driver seat 0 5m a ctl OO At the left foot of the driver seat Panel to right of steering wheel upper part of small storage box lt gt 6 pin 5 pin Connector Connector A If the meter not activate from individual differences in car models or some reasons after the engine starts you need to chang
5. gerous to pull tangled wires by force or allow tangled wires to Do not install the product in a place where it will cause distraction interfere with driving Do not in any manner process take apart or make changes to this product X J any place where water may be splashed Features Our specialized communication analyzer makes it possible to display BOOST data of MAZDA SKYACTIV D Easy Installation Meter Holder included Simple coupler connection to Diagnostic monitor connector The included full cover type holder allows seamless installation to a number of places Dual Display Boost is shown by the needle water and voltage are shown digitally 2 Color Illumination Switch with 3 step Dimmer lllumination switch allows selection between two colors and brightness adjusted with three step dimmer Peak Hold Save and display each peak reading after engine starts Black Titanium Bezel High quality black titanium bezel Part Names and Display Meter Unit View from Gauge Connection E Analog Display EJ Needle EJ Switch Ed Digital Display E illumination J Display Range View from Car Connection if L night illumination Display Boost data Shows the current values and peak value Use to change modes of digital display and reset the peak value Display switches between typ
6. n the key is Demo Panel to Flat Space SS Affix the Cushion Tape to the base of the meter connect the Gauge Cable to the Meter and install the Meter into the Meter Holder Please add the Cushion Tape if the Meter not fixed Cushion Tape Meter Holder Cushion Tape Back side of Meter sot a Cushion Tape Gauge Cable i C Installation to A pillar using A pillar Stand Make a 95 hole on the place to install the meter of the A pillar and fix the Meter using A pillar Stand with Screw and Nut A v4 i A pillar Screw Cfoum A pillar Stand 25 Hole When Fastenings to a Cable or Pipe Through turned ON the needle will move to the extreme left several times for searching position Then it will move to the maximum value and finally to reading for current measurement item Due to analyzation time for the car data transmission it may take up to a few seconds from engine start before opening demo Double sided tape holes Clean to i rr cable The needle stops in the vicinity of lowest value Due to analyzation time for the car data transmission the illumination may remain on for up to 1 minutes even after the engine has been turned off this is normal and no effect on the vehicle performance except wiring IGN Turning off the Display Swit
7. ont of menn Wrap around both Close tightly with cut Insulate with vinyl l idertegaher cover at connection the product s wire wire coils connector tape Installing The Product Installing The Meter A Installation with the Meter Holder Fasten using the double sided tape Nw Double sided tape Clean to remove oil and dust Note Please be sure about where you wish to install the meter as it is not advisable to reuse double sided tape After deciding the position and angle of the meter face fasten the Hexagonal bolt on both sides to secure Hexagonal bolt B Installation to panel or something Cut the Cushion Tape in half affix to base of the Meter to be on press fit condition with adjusting number And connect the Gauge Cable to the Meter and insert into the panel Cut the Cushion Tape in half Installing The Unit Cushion Tape 1 As shown in the below diagram fasten the unit into positions not usually affected by water Example of Installation Gauge i ee Cable Cushion Tape Fastening 7 Under the steering Fl On the back side column cover of the under cover lt Si YW BIN A On the inside of the driver s door q remove f or pipe Basic Operation 1 Engine Start 2 Opening Demo 3 Display Each Mode 4 Engine Stop 5 Meter OFF Opening Whe
8. r use or disregard of these warnings may cause may result in the injury or death of people injury to persons damage the product and other things Do not work in areas where there is excessive exhaust This product is for DC12V cars Due to vehicle exhaust emission poisoning or fire may result in a damage to Installation cannot be carried out on cars with other voltage batteries humans Just after installation do not exert any strong force on the product Do not crush the cable When double sided tape is used for an installation be warned that when hot the tape Please be careful that the cable does not get crushed by the seat rail or car temporarily losses adhesiveness door steel plate nor cut by any sharp steel plate as this may cause a poor Do Not Use Chemical Cleansers connection or an electric short leading to fire or other danger i g A If the unit gets dirty please wipe with a soft cloth to remove any dirt Do not use chemical Do not operate while driving cleansers such as thinner benzene or alcohol Operating or checking the display during driving may cause an accident Do not install the product in any place subject to high temperature or please use with the utmost consideration for safety Please securely fasten the product to a stable place and be mak t i ll d ts to their original pl sure to store bundle away all wires with tape etc ane Sure to replace all Screws and parts to 1nelr original Pace It is very dan
9. ssing will change the color Seiting Completed no operation for 5 seconds u m i n atio n bri g htness sett i n gs OnE case of anxious about reflected illumination of door mirror 1 Press 2 Display a peak value after 3 4 4 Press the switch the switch 3 seconds and the current Ce to change the brightness for 6 seconds brightness after 6 seconds Release the switch a Holding downs the switch after displayed a A n A in operation e g L 3 the current setting L 4 L E L I Ve I 3 lt High gt Mid gt lt Low 5 Ce Release 6 Back to normal display with Each pressing will change the brightness the switch no operation for 5 seconds after setting is done i s Setting Completed Troubleshooting O PIC O DIC a O DIC O O Does not work with Engine start Poor connection of Gauge cable Please reconfirm whether wiring and connections 6 pin Connector or OBD Connector wires are correct or not The unit has been installed into an incompatible Please reconfirm the Fitting List car model Upon starting up the unit will not start in the Because after changing displays if the car s engine is turned off within 3 seconds the new setting will newly changed display not be stored make sure to wait at least 3 seconds before turning the engine off Before the opening demo
10. starts the needle briefly This is due to a special characteristic of the meter and is not a malfunction moves The displayed values are different from the standard Due to the ECU information received the displayed values on this product may differ from those of meter standard or other meters X Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status X We plan in the near future to take all possible legal measures to protect against unfair competition from look alike products using similar designs regulating characteristics circuitry and circuitry layout We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User s Manual PIVOT CORPORATION 87 3 Shimookada Okada Matsumoto shi Nagano 390 0313 JAPAN
Download Pdf Manuals
Related Search