Multi Function Professional Puncher – A1
Contents
1. Die Stop Position On some of the Professional Puncher die sets there is an adjustable die stop which is used to re center the die set for certain sheet sizes as shown in Figure 8 7 For die sets without a die stop knob there is no die stop position adjustment necessary For units with a die stop knob the die stop must be set to the correct position or the punched holes will not be centered on the sheet The common paper sizes are shown on the die stop handle label below the die stop knob for the uncommon paper sizes please refer to Table 8 2 Position A is when the arrow on the die stop knob points down towards the handle and lines up with the lower arrow on the die stop handle label Position B is when the arrow on the die stop knob points to the side and lines up with the side arrow on the die stop handle label See Figure 8 7 To change the die stop position first remove the die from the machine and place on a flat stable surface While holding the die in a stable position push down on the die stop knob until the knob is free to rotate Then turn the knob until the arrow on the knob lines up with the desired arrow on the die stop handle label Once the arrows line up release the die stop knob making sure that the metal die stop on the bottom fully seats against the die plate US Paper Sizes Die Stop Position Based On Paper Size or Orientation Canon Part Number T CC re 8 a a a a2. CORD Type HO5VV F3G0 75 Harmonized lt HAR gt The lt gt symbols indicate cord approved according to appropriate European standard NOTE HAR may be substituted for approval mark of European safety agency that approved the cord An example would be lt VDE gt APPLIANCE CONNECTOR 3 amperes 250 volts 50 60 Hz European safety approved Type IEC 320 The cordset shall not exceed 3 meters in length A cordset with component electrical ratings greater than the minimum specified electrical ratings may be substituted Service Professional Puncher Do not attempt to service your Professional Puncher yourself Contact an authorized service representative for any required repairs or major maintenance for your Professional Puncher A DO NOT REMOVE THE MACHINE S COVER There are NO user serviceable parts inside the machine in order to avoid potential personal injury and or damage to property or the machine itself Service Diesets Every dieset is thoroughly oiled at the factory prior to shipping Please note that it is normal for oil to be present on the first few punched sheets During normal use this oil will be exhausted and should be replaced As part of regular maintenance each dieset should be oiled after approximately 100K punch cycles Canon recommends use of brand 3 IN ONE oil as it is readily available Other light machine oils can also be used To oil the dieset refer to Section 8 Die
3. Paper Bypass Mode Sheet size Punch Capacity Power Supply Electrical Safety Certification Dimensions Weight Shipping Weight Manufactured Paper sizes and stocks same as printer Single Sheet 115V 60Hz Single Phase Amps and Frequency 115V 3 8A 60Hz cULus L 795mm W 445mm H 1040mm L 31 5 W 17 5 H 41 102 kg 225 lbs 135 kg 298 lbs Assembled in Taiwan Multi Function Professional Puncher A1 8 DIE SET USER MANUAL Remove the pressure bar and set aside a The die sets for the Professional Puncher are intended to work with multiple paper sizes and sheet feed directions In order to accommodate different sheet sizes this die set must be configured to the correct number of punching pins and the die stop must be set to Figure 8 3 Pressure Bar the proper position The die label contains information on the common paper punching sizes for uncommon sizes please refer to Table 8 1 O Le Glossary nn p LU LEF Long Edge Feed Indicates that the paper is being fed through ea i a Mn the machine so that the longer side of the sheet will be punched SEF Short Edge Feed Indicates that the paper is being fed through the machine so that the shorter side of the sheet will be punched Statement Paper 8 5 X 5 5 Legal Paper 8 5 X 14 ANNAN NANA Figure 8 4 Pin Removal Ledger Pa
4. a LTR SEF B a B A Aa 8 7 STATEMENT LEF B a B a A 8 7 ense DS ta e a a 8 LEDGER SEF B a a a a A 1 9 x 12 LEF ea a ee NE 9 x 12 SEF CA ey ANR En 12 x 18 SEF B A A Coil Rnc Sa eS aa SS es Table 8 2 Die Stop Position Guide For CombBind 20H Configuration set to die stop position B A alo rain A gi Mc Figure 8 7 Coil Die Stop Position Die Set Maintenance The die sets must be periodically oiled and greased to maintain proper functionality and prevent premature failure of the die set The die set should be oiled and inspected every 100K cycles To lubricate die set pins that do not have felt pads 1 Apply a drop 0 05 ml of 3 IN ONE or high quality light machine oil directly to the pins 2 Depress the top portion of the die set so that the pins protrude from the bottom plate 3 Wipe clean leaving a light coat of oil on them 4 Wipe up any oil that remains on the top of the plates To lubricate die set pins that have felt pads 1 Lubricate with 3 IN ONE oil or a high quality light machine oil 2 Apply a 1 8 3 mm bead of oil lightly along the length of the felt pad 1 but do not over saturate 3 Do not use spray lubricants because they tend to dry up quickly and leave a sticky residue Oil from the die may blemish the first few punched sheets after oil has been applied Run test punched copies until clean copies can be made TI Ti Figure 8 8
5. through the Professional Puncher Step 1 A Crease die set must be inserted to enable the Crease mode See section 4 A for details on Die set changes Step 2 For some controllers before starting a print job select the Crease mode from the printer s UI See printer manual Professional Puncher will now function in Crease mode Note Crease mode is out of specification for certain printer configurations ENTER OK Layout of Professional Puncher LCD User Interface 4 Die Set Configuration To configure the Die Set for the desired sheet size that is being processed see section 8 Die Set User Manual Multi Function Professional Puncher A1 4 USER OPERATIONS A Interchanging Die Sets Your Professional Puncher offers the convenience of interchangeable i interchanging Die Sets die sets allowing you to economically punch documents for a wide Are completed without tools and only take seconds to perform variety of binding styles Changing the machine s die sets is both quick and easy as the following instructions illustrate lii PURE Chip Containers Note For advanced Die Set Configuration instructions See Section 8 Easy to access chip tray for quick chip disposal Die Set User Manual iii Die Set Storage Removing Die Sets from the Machine The inter changeable die set Holds up to 2 spare Die Sets slot of the Professional Puncher is located above the bypass section of the machine iv Punch Bypass Short strai
6. Ready To Crease Professional Puncher is ready to process a crease job For some controllers all sheets through the unit will be creased 4 Running Bypass This is displayed when Bypass mode is in operation 5 Running Punch This is displayed when Punch mode is in operation 6 Running Crease This is displayed when Crease mode is in operation 7 Chip tray Full When the punch container becomes full of waste paper chips this message will be displayed 8 Chip tray Out When the punch container is removed or not fully inserted into the punch unit this message will be displayed 9 Check die When the Die Set is removed or not fully inserted into the punch unit this message will be displayed When this message is displayed the punch unit will run in Bypass mode only 10 Close Door When the Front door is open or not completely closed this message will be displayed 11 Paper jam When a sheet of paper becomes jammed within the punch unit this message is displayed See the section of this manual titled PAPER CLEARING for instructions on how to remove a jammed sheet Multi Function Professional Puncher A1 Changing the Settings on the LCD panel 1 Mode With Crease die inserted crease function can be turned ON OFF Backgage Depth Setting Backgage is the distance of the punched hole s from the trail edge of the sheet This distance can be adjusted by entering the Settings section press Up or Down from the Home scr
7. for details Die sets have an expected use life of 750 000 punches using 20 Ib 5 gsm paper This is a minimum life expectation only Die life is NOT guaranteed due to a wide range of media weights and environmental conditions that the dies may endure If you are going to be punching extended runs that exceed the die use life it is strongly recommended that you have sufficient numbers of the appropriate die sets on hand to continue with minimal downtime Multi Function Professional Puncher A1 3 QUICK START GUIDE Professional Puncher must be connected to AC power to enable any feature of the machine Below are three modes of operation of Professional Puncher 1 Bypass Mode This operation will allow paper to pass through the Professional Puncher without being punched This is the default mode of operation for Professional Puncher Make sure the Punch Icon is not selected in the printers User Interface 2 Punch Mode This operation will punch the trail edge of all sheets that pass through the Professional Puncher Step 1 A properly configured die set must be inserted before running punch mode See section 4 A for details on Die set changes and follow the labels on the die set for configuration Step 2 Before starting a print job select the Punch mode from the printer s Ul Professional Puncher will now function in Punch mode 3 Crease Mode This operation will crease in the middle of all sheets that pass
8. la desconecci n bend s shock because disconnectin I cie l J Do not operate the Professional Puncher if the machine has a power from this section does not cut off power from damaged power supply cord or plug Do not operate the machine Gevaar voor elektrische schokken Pericolo di cortocircuito La after any malfunction Do not operate the machine in case of liquid dit gedeelte schakelt niet de cs da questa me qe inden qe adjacent sections of the I I I van de aanliggende gedeeltes van disconnessione anche in altre spills or if the machine has been damaged In any other Way het apparaat uit sezioni della macchina m achi ne Do not overload electrical outlets beyond their capacity To do so Perigo de choque el trico may result in fire or electrical shock continuar o ligadas Cleaning Electrical shock Risque de ee be Premed serviceable uv Pes da ill You may clean the exterior of the Professional Puncher using a parts inside pieces r parables elar servicing to AE W soft damp cloth personnel personnel qualifi Th IS safety mess ag e means I o not use detergents or solvents as damage to the machine ma D t det t vent d to th h y Spannungsf hrende Teile Nicht ffnen Enthait keine vom Endverbraucher zu wartende Teile F r Service bitte an qualifiziertes Service Personal wenden Kans op elektrische schok Niet openen Bevat geen door gebruik te repareren onderdelen Door bevoegd servicepersoneel lat
9. of binding styles by means of a simple die change It has also been designed for easy operation The Professional Puncher is an innovative solution for punching paper and offers the following design features Quick change die sets that can be interchanged without any tools All Professional Puncher die sets include an Identification Label providing the user with the hole pattern and name Convenient storage area for two extra Die Sets located above the sheet bypass Duty Cycle and Product Positioning The CANON Multi Function Professional Puncher A1 provides a flexible cost effective punching solution for light to medium level punching production environments It is designed for production print users that typically punch their documents at an average of 20 30 of their overall workflow For customers that run continuous punching for long runs of over 4 hours performance may vary or degrade due to a wide range of media weights and environmental conditions that can occur Maximum Recommended Monthly Volume The maximum recommended monthly punch volume should NOT exceed 400 000 Operating Die Set Supplies Dies are considered consumables and when worn must be replaced since sharpening is not possible Each die set has a 90 day warranty from the date of purchase The warranty Is void if the die is used beyond its specifications Punch die life will be maximized if oiled every 100 000 punch cycles see Dieset Service
10. Lubrication End of Die Life If a die set is at the end of its life it will tend to cause paper jams due to hanging paper chips This is a result of die plate wear and not pin wear which cannot be corrected When this occurs the die set must be replaced with a new one Attempting to replace or sharpen pins will not correct the issue and therefore is not recommended Die Set Handling There is a chipset located in the die set which should not be touched during die set handling Do not attempt to touch the chipset reader located inside the machine as this may result in damage to the punch 11 Multi Function Professional Puncher A1 Professional Puncher Die Sets The Professional Puncher uses a variety of easily interchangeable die sets that allow you to punch documents in line for several different binding styles By selecting the appropriate die set you can use your Professional Puncher to punch documents in any of the following binding styles For Plastic Comb Binding High Durability Option available O E EE HE HE HE EE HE HE HE HE HE HE HE HE HE HE eee E 1 19 LTR 21 A4 Die Canon Comb Bind Die Canon Comb Bind HD PB Plastic Bind Hole Size 8mm x 2 9mm 0 313 x 0 116 LxW Center to Center Hole Spacing 14 3mm 0 563 For Twin Loop Binding OBB BRB RRR RRR Ree ee eee eee eee ee eee oeo 1 32 LTR 34 A4 W3 Wire Square 3 Holes per inch Hole Size 4mm x 4mm 0 156 x 0 156 L x W Center to Center Hol
11. Multi Function Professional Puncher A1 Operation Instructions Manual CF Manuel d instructions et d utilisation CE Manual de instrucciones de operaci n Part Number 7715006 Revision number 1 Issue Date June 2015 o 08 Multi Function Professional Puncher A1 English 3 Francais 13 Espanol 23 Please read these instructions carefully and keep them in a safe place for future reference Lisez attentivement le present manuel et conservez le en lieu sur afin de pouvoir le consulter en cas de besoin Lea estas instrucciones cuidadosamente y mant ngalas en un lugar seguro para consulta en el futuro Multi Function Professional Puncher A1 TABLE OF CONTENTS 1 SAFETY INSTRUCTIONS 3 5 USER DISPLAY Important safeguards 3 6 PROBLEM SOLVING Cleaning 3 7 SPECIFICATIONS 9 Service 4 8 DIE SET USER MANUAL 10 Safety messages 4 2 INTRODUCTION 4 3 QUICK START GUIDE 5 4 USER OPERATIONS 6 Important safeguards A THE SAFETY OF YOU AND OTHERS IS VERY IMPORTANT TO CANON CORPORATION IMPORTANT SAFETY MESSAGES AND INFORMATION ARE CONTAINED IN THIS MANUAL AS WELL AS ON THE MACHINE ITSELF PLEASE MAKE SURE YOU CAREFULLY READ AND UNDERSTAND ALL OF THESE BEFORE OPERATING THE MACHINE A Use the Professional Puncher only for its intended purpose of punching paper and covers according to the indicated specifications Retain this Operation Instructions manual for future use CAUTION THE PRINTER O
12. N OFF SWITCH DOES NOT THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY CUT OFF POWER FROM THE PUNCH MESSAGE IN THIS OPERATION INSTRUCTIONS MANUAL THIS SYMBOL INDICATES A POTENTIAL PERSONAL SAFETY HAZARD THAT COULD HURT YOU The Professional Puncher must be connected to a supply voltage OR OTHERS corresponding to the electrical rating of the machine operation instructions also listed on the serial number label THE FOLLOWING PICTORIAL IS FOUND ON THE PROFESSIONAL o PUNCHER The grounding plug is a safety feature and will only fit into the proper grounding type power outlet If you are unable to insert the plug into an outlet contact a qualified electrician to have a suitable outlet installed Electrical shock hazard Discon Risque de necting power lectrique Couper 2 ily Do not alter the plug on the end of the cordset if provided of the from this section e circuit lectrique dos not remove dans ce secteur ne Professional Puncher It is provided for your safety adjacent sections Le np pe t of the machine mache Unplug the Professional Puncher before moving the machine or This safety message MES whenever the machine is not in use for an extended period of Elektroschockgefahr Abschalten Riesgo de choque el ctrico you Cou Id get an electrical ti des Stroms von diesem Teil der El desconectar la fuente de Im e j Maschine unterbricht nicht den alimenaci n de esta secci n n I j rom von anliegenden Teilen der reviene
13. Set User manual Please note that it is normal for oil to be present on the first set of sheets punched after oiling the dieset After approximately 25 to 50 sheets oil will no longer be found on the punched sheet At this time the Professional Puncher can be utilized for punching of print jobs See Section 8 Professional Puncher Dieset Manual for further instructions on servicing the Diesets Safety messages A FCC NOTE THE FOLLOWING NOTE ONLY APPLIES TO THE UNITS RATED 115V 60Hz This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Operation Manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense CAUTION CHANGES OR MODIFICATIONS NOT A EXPRESSLY APPROVED BY GENERAL BINDING CORPORATION COULD VOID YOUR AUTHORITY TO OPERATE THE EQUIPMENT 2 INTRODUCTION Thank you for purchasing the Professional Puncher It is a versatile production system that will enable you to punch documents for a variety
14. al number of punched sheets the system has processed Firmware This displays the current level of firmware of Professional Puncher Multi Function Professional Puncher A1 7 SPECIFICATIONS Punch and Crease Sheet US Sizes 6 PROBLEM SOLVING Probable Cause Probable Cause Size and Edge LTR LEF Punch only No power won t punch Power cord not attached to back LTR SEF of machine or not properly LEF Long Edge Fed 8 Y2 x 5 2 LEF Punch only 11x17 SEF Power On Off Switch not 9 x 12 SEF Punch only activated 9 x12 LEF Punch only 12 x 18 SEF Punched holes not aligned with Follow instructions on die set 12 6 x 19 2 Crease only the edge of the paper labels to properly configure the 13 x 19 Crease only die for a specific sheet size 13 x 19 2 Crease only ISO sizes Sheet jamming repeatedly at die Remove the die set inspect the A4 LEF Punch only set area die throat to see if there is any A4 SEF stuck paper chad A5 LEF Punch only A3 SEF Insert Chip tray message on the Make sure the Chip tray is fully SRA4 SEF Punch only i SRA4 LEF Punch only LCD interface inserted SRA3 SEF Tab Stock US Sizes LTR with 3 4 5 8 10 12 25 26 27 tabs 160gsm 300 gsm 8 12 x 5 12 With 3 5 tabs ISO Sizes A4 with 5 10 12 25 26 27 tabs 160 300gsm A5 with 3 5 tabs Paper Stock Plain 75gsm 300gsm 20 bond to 110 cover Coated 120gsm 300gsm 32 bond to 110 cover Clear Cover 7mil
15. e Spacing 8 5mm 0 333 mE E E E Eggan g g g ggg g g g g MI 21 LTR 23 A4 W2 Wire Rectangle 2 Holes per inch Hole Size 6 4mm x 5 4mm 0 250 x 0 214 L xW Center to Center Hole Spacing 12 7mm 0 500 Die Canon Wire 3 1 Sq Die Canon Wire 2 1 Sq 0000000000 00000000 00000000 0 0 00 0 00 OV 1 32 LTR 34 A4 W3 Wire Round 3 Holes per inch Hole Size 4mm 0 158 Diameter Center to Center Hole Spacing 8 5mm 0 335 0 600000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 O 1 21 LTR 23 A4 W2 Wire Round 2 Holes per inch Hole Size 6 5mm 0 0 256 Diameter Center to Center Hole Spacing 12 7mm 0 5 Die Canon Wire 3 1 Rnd Die Canon Wire 2 1 Rnd For Color Coil Binding High Durability option available O000000000000000000000000000000000000000000000 Die Canon Coil Rnd 1 44 LTR 47 A4 Die Canon Coil Rnd HD C4 Coil Round 4 Holes per inch Hole Size 4 4mm 0 174 Diameter Center to Center Hole Spacing 6 3mm 0 2475 For Velo Bind Die Canon Velobind 11 Holes Ltr e 11 VB Velobind Round 1 Hole per inch Hole Size 3 2mm 0 125 Diameter Center to Center Hole Spacing 25 4mm 1 Die Canon Velobind 12 Holes A4 Die Canon 3 Hole 8mm Die Canon 3 Hole 8mm HD 3 Ring 5 Ring 7 Ring U S Standard Loose leaf Patterns Hole Size 8mm 0 316 Diameter 4 Ring Binder European Standard Loose leaf Patterns Hole Size 8mm 0 315 Diameter Die Can
16. een and press OK for Settings Pressing Up arrow will increase the Depth of Backgage and Pressing Down arrow will decrease the Depth of Backgage BACKGAGE ON THE LCD ON THE LCD DECREASES INCREASES BACKGAGE BACKGAGE DEPTH DEPTH When a crease die is inserted the Backgage Depth options is 1 Crease Mid CREASE LINE ON THE LCD 4 ON THE LCD MOVES THE MOVES THE CREASE LINE IN THIS DIRECTION CREASE LINE IN THIS DIRECTION PAPER FLOW DIRECTION Alignment Setting Alignment is the distance of the Top punched hole from the side edge of the sheet viewed from the punch output orientation This distance can be adjusted by entering the Settings section press Up or Down arrow from the Home screen and press OK for Settings Pressing Up arrow will increase the Alignment position and Pressing Down arrow will decrease the Alignment position ON THE LCD INCREASES ALIGNMENT OFFSET ALIGNEMENT ON THE LCD DECREASES ALIGNMENT OFFSET O Clear Cover The Backgage Depth setting and Alignment setting for Clear Cover media can be adjusted using this function Language The LCD panel can be configured to display one of the following languages English Francais Espanol Deutsch or ltaliano Displaying Information on the LCD Panel Die type The type of die set that is presently installed in the machine will be displayed Punch cycles This is the tot
17. emoval Pin Numbers to Remove Based On Paper Size or Orientation Canon Part Number Be me oo a has La Now EH La fa NONE sa NONE ba NONE ba LeoGersEr 247 123 L34 NONE Hs NONE N x18 r23 3a 3 pousse zar La fsa Now FH NONE Canon Part Number I uP ff haie NON NONE NONE Wa wa an aan NONE N A NONE NONE NONE NONE A za 4 LEF ma SE pa N A 2H fH JNONE a na 19d oo AS LEF pa azn fso na N A HH JNONE N A INA 425 30 N N S S 6 7 42 4 21 NONE NONE NONE N A N A 2H 4H PH 4H JNONE N A NONE JNONE SRA4SEF 6 7 42 41 4 21 4 5 30 31 N A N A N A N A NONE N A N A 4 19 4 21 4 5 30 31 SRA3 SEF NONE None NONE N A N A 2H 4H 2H 4H JNONE N A NONE JNONE None _ None For CombBind 20H Configuration Pull Pin Number 1 Table 8 1 Pin Removal Guide The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the Professional Puncher can accept For standard offering dies not found in the chart no pin adjustment is necessary Multi Function Professional Puncher A1 Pin Addition The process for adding punch pins is the same as pin removal except that pins are added and not removed once the pressure bar is off When replacing punch pins make certain that the pins are completely seated against the pin retainer prior to reattaching the pressure bar CORRECT CORRECT INCORRECT Figure 8 6 Pin Addition
18. en repareren Perigo de choque el trico Nao abra Nao h nenhuma pe a na parte interna que possa ser manuseada pelo susuario A manauten o deve ser realizada por pessoas qualificadas Riesgo de choque el ctrico No abra Adentro no hay piezas reparables para el usuario Mantenimiento solamente para personal calificado Pericolo di scarica elettrica Non aprire Nessuna parte riparabile dall utente Chiamare un servizio di riparazioni qualificato that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage NEVER remove the screwed on covers ALWAYS refer service requirements to qualified service personnel occur Multi Function Professional Puncher A1 Safety messages A MAIN CORDSET SELECTION THE FOLLOVVING NOTE APPLIES ONLY TO THE UNITS RATED 230V 50Hz AND LOCATED IN THE EUROPEAN UNION CAUTION WHEN CHOOSING A DETACHABLE LINE CORD FOR USE WITH YOUR PROFESSIONAL PUNCHER ALWAYS FOLLOW THE FOLLOWING PRECAUTIONS The cordset consists of three parts the attachment plug the cord and the appliance inlet Each of these components must have European regulatory safety approvals The following minimum electrical ratings for the specific cordset are published for safety purposes DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS PLUG 3 amperes 250 volts 50 60 Hz Class 1 3 conductor European safety approved
19. er is jammed in the right bottom chute press the top lever while holding the bottom lever This will unlatch the chute continue to open the chute until it reached the magnet on the right side Reach in and remove the paper To return the chute to the closed position move it back in the opposite direction until the latch mechanism is activated Ensure the paper chute is closed Area B3 If paper is jammed in the left bottom chute unlatch the chute reach in and remove any jammed paper Ensure the paper chute is closed Area B4 If paper is jammed in the upward paper chute move the door to the left reach in and remove the jammed paper Ensure the paper chute is closed Area B2 B3 Before uninstalling the die set ensure Area B2 and B3 are cleared of any jammed paper If there is jammed paper cannot be removed from Area B2 and B3 uninstall the die set to remove the jammed paper see Section 4 Changing the Interchangable die sets 5 USER DISPLAY Located on the top of the Professional Puncher is a user interactive LCD panel that provides Messages Settings and Information relating to the functions of the punch unit Main Screen SETTINGS INFORMATION LCD Panel Overview Messages on the LCD Panel 1 Ready Bypass Professional Puncher is ready to bypass sheets will not be punched 2 Ready To Punch Professional Puncher is ready to process a punch job all sheets through the unit will be punched 3
20. ght through paper path for unpunched documents Step 1 Stop the printer copier Step 2 Open the Professional Puncher access door panel v Punch Mode Path Step 3 Securely grasp the die lock handle and rotate it in the Wide radius turn can support stocks up to 300g m cover CCW direction as indicated in the label near the die lock handle This releases the die from the locked position Step 4 Slide the die set out until it is fully removed supporting it with both hands Step 5 Properly store the removed Die Set in the Die Set storage area of the Professional Puncher keep away from dust dirt accidental falls from the edge of counters etc Step 6 Select the desired Die Set for your new job and slide it into the Die Set slot Push the Die set firmly until the Die stop feature contacts the round magnet This is critical in ensuring the proper position of the die set Step 7 Grasp the handle and rotate it in CW direction until the latch is fully engaged as shown indicated in the label WARNING POSSIBLE PINCH POINT HAZARD WHEN A INSTALLING DIE SETS IN YOUR PROFESSIONAL PUNCHER ALWAYS KEEP FINGERS AND OTHER BODY PARTS OUT OF THE MACHINE S DIE SET SLOT AND AWAY FROM ALL AREAS OF THE DIE SET EXCEPT FOR THE FINGER HOLE IN THE DIE SET FAILURE TO FOLLOW THESE PRECAUTIONS MAY RESULT IN INJURY Step 8 Close the Access Door Panel Step 9 Proceed with your printing and punching job Please note that when u
21. on 3 5 7 Hole 8mm Die Canon 4 Hole 8mm Die Canon 4 Hole 6 5mm 4 Ring Binder European Standard Loose leaf Patterns Hole Size 6 5mm 0 256 Diameter Die Canon 4 Hole Scan 4 Ring Binder Scandinavian Standard Loose leaf Patterns Hole Size 6 5mm 0 256 Diameter Graphics do not represent actual punch pattern dimensions or spacing For Creasing Die Canon Crease Crease 12
22. per 11 X 17 Note Lubricating oil may be present on the die pins wear gloves if needed Pin Numbering Lift up and remove the desired pins according to Table 8 1 Store pins in the pin storage tray inside front door of machine making sure pins Die punching pins are numbered sequentially starting from the handle cannot be dropped damaged or lost while removed end Figure 8 1 shows a 47 hole coil die as an example All square and round hole die sets follow the same pin numbering format o Lee 3 Da tt L 1 Le ee IE i VAAN mn Figure 8 5 Replace Pressure Bar Replace the pressure bar by lining up dowel pin holes with exposed dowel pins Hold pressure bar so that it is seats completely over dowel es FR pins and then rotate Quarter Turn Fasteners clockwise until a click is RA P felt to lock pressure bar in position The pressure bar can be locked Wi only if the orientation is correct it cannot be locked in any other LL TT en orientation E Important Make sure pressure bar is attached and both Quarter Turn Fasteners are in the locked position prior to inserting the die set into Figure 8 2 Pressure Bar Removal the machine or serious damage can occur to both the machine and die set To remove punch pins from the Professional Puncher first turn the two Quarter Turn Fasteners CCW direction to release the pressure bar Pin R
23. sing a new die some oil will be present around the punched holes on the sheet After punching 25 to 50 sheets the die will no longer leave oil on the sheets It is recommended that a short test print job be run after installing a new die or a die that has recently been oiled B Punch Chip Container The Punch Chip Container for your Professional Puncher is located at the front of the machine s base The drawer should periodically be pulled out and emptied The Professional Puncher uses a sensor to determine when the punch container is full Once the punch container becomes full the LCD display shows Chip Tray Full message and a message also appear on the printers user interface screen Paper flow and User Interactive sections of Professional Puncher Multi Function Professional Puncher A1 C Paper Clearing O When paper is jammed in the paper path of oW Professional Puncher the LCD display shows the area where a sheet s is jammed Area Description Area A If paper is jammed in the Punch Bypass lift the handle until it latches with the locking mechanism Reach and remove the jammed paper To close the paper guide press the upper latch lever while holding the guide plate handle and lower the guide plate to close it firmly Area B1 If paper is jammed in the downward paper chute move the chute to the right reach in and remove the jammed paper Ensure the paper chute is closed Area B2 If pap
Download Pdf Manuals
Related Search