XTREME VALUE TOWER SERIES (XVT) USER`S MANUAL
Contents
1. Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 14 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Please handle the UPS and associated equipment with extreme caution since a high amount of energy is contained in the batteries Always keep the unit in an upright position as marked on the packaging and never drop the unit Please adhere to the following instructions if the UPS is not installed immediately e Store the equipment as is in its original packing and shipping carton Do not store in temperatures outside the range of 15 C to 25 e Ensure that the equipment is fully protected from wet or damp areas and from moist air In order to maintain the batteries the UPS should be recharged every 6 months for at least 8 hours If flammable substances such as gases or fumes are present or if the room is airtight a hazardous situation may exist in which no electrical equipment should be operated The instructions in this manual explain how to install the UPS safely Not acknowledging such electrical hazards may be fatal keep this manual for future reference WARNING It is strongly recommended that the UPS cabinet not be opened as components have very high voltage and touching those components may be fatal Only a qualified technician or authorized agent may service the unit The UPS unit s output receptacles carry live voltage even when not connect2. s ST EXE WT NEC suc M 4 NXRT EBP FRONT PANEL Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 45 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS LED Description The Charging LED GREEN indicates that the battery charger in the Extended Battery Pack is charging normally with the AC power cord attached to the Battery pack The Battery Test LED GREEN indicates that the DC output of the Extended Battery Pack EBP is normal To perform the Battery Test e switch the breaker on the rear of the to ON position e press the Battery Test Button on the front panel of the e the DC output from the is normal when the Battery Test LED is illuminated Prior to connecting EBP s test each EBP to assure proper operation Extended Battery Pack Operation The NXRT UPS System can be connected to multiple extended battery packs to increase the runtime when connected to the UPS supporting the load Most UPS Systems are limited to one or two external battery packs because the UPS is responsible for the recharging and does not have the recharge capacity to handle the additional batteries to a full recharge The NXRT UPS System overcomes this limitation by equipping each extended battery pack EBP with its own charger providing the user a way to achieve significantly more battery backup time Not all of the AC input power cords for the
3. ______ __________ _ 18 Wall mounted Installation Steps 19 19 Rack mount using 5 in 1 bracket 20 RACK MOUNT INSTALLATION STEPS 21 UPS Rail Installation Instructions to 19 12 2 2 2 2 nnns 21 INITIAL CONNECTION AND STARTUP J 24 Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 2 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS USER S OPERATIONS uq nat DI RUE ENIM Ne REV AP UN URS 26 Turning Off the UPS when connected to an AC source 26 Starting the UPS from a DC source cold start tenente 26 Turning Off the UPS when in DC ert td ettet cr tacita cr ertt 26 STEMS BIS dr HIS INN E T TT 27 Audible Alarm silence in DC Mode or Fault Mode 27 e 28 REPLACING THE BATTERY EE 28 TROUBLESHOOTING 31 32 SPECIFICATIONS tum s 33 SHIPPING LIS id esee Ex 36 OBTAINING SERV ICE Fa do 37 XTREME POWER CONVERSIONS XPC CORPORATION LIMITED WARRANTY e 38 XTREM
4. fire flood and wind Damage caused by abuse misuse alteration modification or negligence Any labor costs or travel room and board expenses associated with the repair and or restoration of lost or damaged hardware software or data EXCEPT AS EXPRESSLY PROVIDED IN THIS POLICY XPC SHALL NOT BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO DIRECT INDIRECT SPECIAL INCIDENTAL CONSEQUENTIAL OR MULTIPLE DAMAGES ARISING OUT OF THE USE OF THE PRODUCT OR DAMAGE TO THE CONNECTED EQUIPMENT REGARDLESS OF THE LEGAL THEORY ON WHICH SUCH CLAIM IS BASED EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE SUCH DAMAGES INCLUDE BUT ARE NOT LIMITED TO LOSS OF PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF USE OF THE PRODUCT OR THE CONNECTED EQUIPMENT OR ANY ASSOCIATED EQUIPMENT LOSS OF SOFTWARE COST OF CAPITAL COST OF ANY SUBSTITUTE EQUIPMENT FACILITIES OR SERVICES DOWNTIME THE CLAIMS OF THIRD PARTIES INCLUDING CUSTOMERS AND INJURY TO PROPERTY Submitting a Load Protection Policy Claim e ool 1 Any claim under the Load Protection Policy must be made within 10 days of the date of alleged damage to the Connected Equipment 2 Call the XPC technical support department at 1 800 582 4524 and obtain a Load Protection Policy Returned Material Authorization RMA number Have information on all applicable insurance or other resources of recovery payment that is available to the Purchaser and the name of the power utility sup
5. 7 13 Page 40 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS to make any representations beyond those made in this agreement concerning the Load Protection Policy XPC Corporation 230 Yuma Street Denver CO 80223 1 800 582 4524 RS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 41 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS APPENDIX A EXTENDED BATTERY PACK USER GUIDE Estimated Run Time for UPS with Extended Battery Packs RUNTIME FOR OF EXTENDED BATTERY PACKS IN MIN VA WA ues 2 4 5 NXRT 1000 1500 1050 18 67 123 184 315 NXRT 3000 2100 120 152 Note for estimated run times using more than 5 EBP s contact Xtreme Power Conversion at support xpcc com ee ee Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 42 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS CAUTION It is very critical to connect the correct voltage with the UPS intended EBP1 is for NXRT 1000 EBP2 is for NXRT 1500 EBP3 is for NXRT 2000 3000 CONNECTING THE INCORRECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS AND OR BATTERY PACK WILL VOID THE WARRANTY All EBP s have a different DC voltage configuration intended only for the UPS s listed above PLEASE D
6. LED will no longer be illuminated This is normal operation for the EBP The EBP is working properly SS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 49 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 5 Why don t the LED s on each EBP connected to an AC input source turn ON and OFF at the same time e The charger on each functions independently from the others One charger may be charging while another one might be at 10096 and the charger turned off This is normal operation of the EBP Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 50
7. brackets gy MV dcr 1 set of horizontal mounting brackets lt _________________ ___________________________ Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 36 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS OBTAINING SERVICE If the UPS requires Service Use the TROUBLESHOOTING section in this manual to eliminate obvious causes Verify there are no circuit breakers tripped Call your dealer for assistance If you cannot reach your dealer or if they cannot resolve the problem call Xtreme Power Conversion Corp Technical Support at 800 582 4524 Technical support inquires can also be made at support xpcc com Please have the following information available BEFORE calling the Technical Support Department a Your name and address The serial number of the unit Where and when the unit was purchased All of the model information about your UPS Any information on the failure including LED s that may or may not be illuminated 560 Dem A description of the protected equipment including model numbers if possible A technician will ask you for the above information and if possible help solve your problem over the phone In the event that the unit requires factory service the technician will issue you a Return Material Authorization number If you are returning the UPS to Xtreme Power for service please follow these procedures 1 Packthe UPS
8. power requirements Backup time required will indicate the battery size needed If the load is less than the UPS nominal power rating then actual backup time is longer e The following options are available o Extended Battery Packs NXRT EBP1 for 1000 NXRT EBP2 for 1500 NXRT EBP3 for 2000 3000 o Connectivity Options SNMP WEB card o Xtreme Power Distribution Units XPDU See the Specification section of this manual for additional model information _ E Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 9 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS BATTERY INTERNAL COMMUNICATION REPO SOCKET SNMP SLOT SWITCH OUTPUT I NPUT INPUT COMMUNICATION SOCKET BREAKER SOCKET INTERFACE NXRT 1000 REAR VIEW INPUT INTERNAL COMMUN ICATION BREAKER SNMP SLOT T SWITCH IL mo o B8 e 52 ba ID _ P lo OUTPUT BATTERY AC INPUT FAN COMMUNICATION SOCKET SOCKET INTERFACE NXRT 1500 REAR VIEW OUTPUT INTERNAL COMMUNI CATION SOCKET SNMP SLOT FAN NTERFACE COMMUNICATION QUTPUT HIGH CURRENT INPUT INPUT BATTERY SWITCH BREAKER OUTPUT SOCKET BREAKER SOCKET NXRT 2000 REAR VIEW Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 10
9. the event that the internal EBP charger draws excessive current Extended Battery Pack Installation CAUTION Extended Battery Pack EBP Installation should be performed by qualified service personnel 1 Verify that the DC circuit breaker on the rear panel of the EBP is in the OFF position 2 Turn the UPS OFF and disconnect the UPS Input Cord from the AC wall outlet 3 Remove the EBP connector cover from the UPS rear panel 4 Connectthe external DC battery cable from the EBP to the appropriate connector on the UPS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 48 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 5 Secure the DC battery cable to both the rear of the UPS and the rear of the by using 8 screws provided 2 each per connector end 6 Repeat the above procedure for testing and securing each additional EBP required CAUTION Do not use extension cords when connecting input AC power to UPS or EBP s 7 Move the DC circuit breaker on the rear of each to the ON position At this point the UPS will need to be started 8 If the EBP s are plugged into an AC source and properly installed the internal batteries will be charged when acceptable voltage is present EBP s must be charged for a minimum of 6 hours for full battery time NOTE If the EBP is going to be out of service or stored for six months or
10. 50dba at one meter Altitude 11 500 ft 3500 m above sea level WARRANTY Three years electronics Three years batteries APPROVALS North America UL cUL FCC INDICATORS amp ALARMS Input output voltage amp frequency on line mode back up mode battery capacity load level Audible Alarm Beep every 4 sec on battery UPS Faut Continuous beeping sound and LCD display LCD Visual Display Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 34 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS seen 50 60 Hz auto sensing Ree _ BATTERY Battery Type sealed non spillable maintenance free valve regulated lead acid _ ma mem one EXTENDED BATTERY EE PACK MODELS NXRT EBP1 NXRT EBP2 NXRT EBP3 WARRANTY Warranty Three years electronics Three years batteries APPROVALS North America UL cUL FCC INDICATORS amp ALARMS LED Visual Display Charging LED Battery test LED Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 35 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS SHIPPING LIST 1 1 UPS 1 User s and Installation Manual 1 6 ft RS232 cable 1 UPSILON CD monitoring software 2 sets of 5 in 1 mounting
11. BP2 Use x 6 screws on places marked with letter A NXRT 2000 NXRT 3000 NXRT EBP3 Use M4 x 6 screws on places marked with letter A F Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 17 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Vertical Installation Steps NXRT 1000 NXRT 1500 NXRT EBP1 NXRT EBP2 Use M4 x 6 screws on places marked with letter NXRT 2000 NXRT 3000 NXRT EBP3 Use M4 x 6 screws on places marked with letter A Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 18 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Wall mounted Installation Steps NXRT 1000 NXRT 1500 NXRT EBP1 NXRT EBP2 Use M5 x 12 screws on places marked with letter B NXRT 2000 NXRT 3000 NXRT EBP3 Use M5 x 12 screws on places marked with letter B Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 19 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 19 Rack mount using 5 in 1 bracket NXRT 1000 NXRT 1500 NXRT EBP1 NXRT EBP2 Use M5 x 12 screws on places marked with letter B NXRT 2000 NXRT 3000 NXRT EBP3 Use M5 x 12 screws on places marked with letter B Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 20 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRU
12. E POWER CONVERSION LOAD PROTECTION POLICY eR Error Bookmark not defined APPENDIX A EXTENDED BATTERY PACK USER GUIDE 39 Estimated Run Time for UPS with Extended Battery Packs 42 MM 46 Extended Battery Pack Opera Otivissssssiviassstsissiscaaeatecousacvbassiwtasselabso sdadeatosousactbusshwiassalabioisdagentbsorsnctbnashe 46 Extended Battery Pack Installation scssssssssssssesssssessssssesssssessessecssssussessssessssucesssisessssecsessiesessseseesseeeten 48 Extended Battery Pack Q amp A dicc 49 e Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 3 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Thank you for selecting this uninterruptible power supply UPS It provides you with protection for connected equipment Please read this manual before installing the NXRT Series UPS models NXRT 1000 NXRT 1500 NXRT 2000 and NXRT 3000 as it provides important information that should be followed during installation and maintenance of the UPS and batteries allowing you to correctly set up your system for the maximum safety and performance Included is information on customer support and service if it is required If you experience a problem with the UPS please refer to the Troubleshooting section in this manual to correct the problem If the problem is not corrected please collect information so that the Technical Sup
13. E POWER SUPPLY UPS Xtreme Power Conversion Load Protection Policy THIS POLICY 15 NOT AWARRANTY REFER TO THE XPC CORPORATION INC LIMITED WARRANTY FOR INFORMATION CONCERNING THE WARRANTY FOR YOUR XPC PRODUCT THE LIMITATIONS AND CONDITIONS CONTAINED IN THIS POLICY DO NOT AFFECT THE TERMS OF THE XPC LIMITED WARRANTY Definitions 1 Product means a Standard 120 208 or 240 Volt power protection device that is used in the United States and Canada This policy does not include custom manufactured products 2 Power Disturbance means an AC power line transient telephone line or Local Area Network if applicable spike or surge 3 Connected Equipment properly connected electronic equipment 4 Fair Market Value of damaged Connected Equipment as determined by XPC shall be the lower of a the average price the same or similar items are being sold for on eBay b the price list of Orion Blue Book or if such price list is no longer published a published or announced price list reasonably selected by XPO c the lowest price the same or similar items can be purchased for in the United States or d the total amount of all payment s you have or are entitled to receive from insurance other warranties extended warranties a legal liability claim or from other sources or persons for the damaged Connected Equipment 5 Purchaser means the person or entity that originally purchased the Product from an authorized reseller or distribut
14. EBP s need to be connected to AC the more you connect the faster the recharge of the batteries 1 The DC Circuit Breaker on the rear of the connects and disconnects the DC bus voltage from the EBP to the UPS The DC Circuit Breaker will also trip to the OFF position in the event of an over current condition in the EBP BREAKER 125 ON INPUT 110V 120V 60Hz Max3A mI The equipment must be BREAKER 50A 230Vac connected to the power socket with the grounding EBP2 REAR VIEW Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 46 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 2 The EBP s use a cable shipped with each EBP to daisy chain together additional EBP s to the first EBP being connected to the UPS in the appropriately labeled connector or for connecting the first EBP to the UPS UPS gt 5 daisy chain to UPS or other 3 The AC input cord is for connecting AC utility to operate the Charger contained in each EBP Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 47 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS MSN 5 Gre 5 daisy chain to UPS or other 4 The input AC Circuit Breaker will trip to the OFF position in
15. HE SETTINGS SECTION FOR YOUR SPECIFIC INSTALLATION 8 After charging is complete connect the loads to the UPS while monitoring the load levels via the UPS LCD or via the software Do not connect any devices that have the possibility of overloading the UPS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 25 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Refer to the Troubleshooting section and or Technical Support with any problems during setup USER S OPERATIONS The only operations that users are permitted to do are e Turning the UPS unit ON or OFF e Operating the user interfaces e Connecting data interface cables e Changing the batteries All such operations are to be performed exactly as instructed in this manual The greatest care possible must be taken for any of these operations and any change thereof may prove very hazardous to the operator On Off Button Function Button Inquiry Button Turning Off the UPS when connected to an AC source e Press and hold the ON OFF button for more than 3 seconds to turn off the UPS This means the internal inverter has been deactivated The unit will run a self test prior to the deactivation of the inverter e The green LED will be off and the yellow LED will be on The LCD display will indicate On BPS which means the UPS in providing no output Starting the UPS from a DC source cold start e Assure that t
16. IOT REME Power Conversion UNINTERRUPTIBLE POWER SUPPLY UPS NXRT Online Low Voltage Models USER amp INSTALLATION MANUAL WWW Xpcc com 2013 Xtreme Power Conversion Corporation All rights reserved NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Table of Contents Statements FCC Part 15 ns D IMPORTANT SAFETY INSTRUCTIONS 6 INTRODUCTION sna annainn ananasa aaa 8 PRODUCT DESCRIPTION l 8 Double Conversion On Line Technology 8 uuu un 9 SYSTEM CONFIGURATION iu a ua 9 BR neu gach iti uL UM Ren M OE NL EATUR E eR 11 ON 12 13 SNMP Communications Option cease 13 Remote Emergency Power Off REPO Port nn treten 14 DETERMINING THE POWER REQUIREMENTS OF YOUR EOUIPMEN u l li l 14 HARDWARE INSTALLATION GUIDE nnns 14 ordeo UD 16 s Lida rae k c umo AI MM ML UA MM IM 16 19 Cabinet Ear IMStalll ation 17 Vertical Installation Steps
17. NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS OUTPUT INTERNAL COMMUNICATION SOCKET SNMP SLOT FAN REPO INTERFACE COMMUNICATION OUTPUT HIGH CURRENT INPUT INPUT BATTERY SWITCH BREAKER OUTPUT SOCKET BREAKER SOCKET NXRT 3000 REAR VIEW LED Green light LED Yellow light LED Red light A A A 9 e T 6 6 6 NXRT FRONT CONTROL PANEL LED Description The UPS has three LED s on the front control panel These LED s allow the user to quickly understand if any action is needed Red LED If this LED is illuminated it indicates a fault and the UPS will have no output Faults that would indicate this alarm condition include e Overload e Inverter fault e BUSfault e Over temperature fault Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 11 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Yellow LED If this LED is illuminated it indicates the user needs to take some action and included UPSin Bypass Mode e Batteries Overcharged e Charger fault e Fan fault e Batteries discharged to low voltage level Green LED If this LED is illuminated it indicates that everything is normal and the UPS is being powered by incoming AC utility or by the batteries LCD Descriptions There are four lines of information in the LCD display Each line provides specific information related to the unit stat
18. O NOT MIX EBP s AND MAKE SURE YOU ONLY CONNECT THE EBP TO LIKE EBP s OR UPS INDICATED ABOVE DC VOLTAGES ARE MARKED ON BOTH THE UPS AND THE MAKE SURE THEY MATCH CAUTION CAUTION LABEL CABLE CONNECTORS PLEASE CHECK VOLTAGES CAREFULLY LS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 43 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Extended Battery Pack Configuration e INPUT BATTERY E INPUT BREAKER socker FAN SOCKET BATTERY BREAKER Fe or 9 e P 2 4 J AN wy dE Er O j 0 ur reme y S lt Sd n Ee 9 v EXTENDED BATTERY PACK 1 EBP1 FOR NXRT 1000 TT BATTERY BREAKER palio FAN INPUT BREAKER oy o a INPUT SOCKET EXTENDED BATTERY PACK 2 EBP2 FOR NXRT 1500 Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 44 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS BATTERY BATTERY BREAKER SOCKET FAN INPUT BREAKER INPUT SOCKET EXTENDED BATTERY PACK 3 EBP3 FOR NXRT 2000 3000 CHA RGING LED BATTERY TEST LED C Serr nia ER c atl puc a 5 m UN w E uet S 4
19. PTIBLE POWER SUPPLY UPS RACK MOUNT INSTALLATION STEPS UPS Rail Installation Instructions to 19 Cabinet 1 2U EAR FOR UPS MOUNING IN CABINET EXPANDABLE RAIL FOR UPS OR EBP MOUNTING IN CABINET MOVEABLE NUT FOR MOUNTING RAIL KIT IN CABINET w vrw _ _ Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 21 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 4 ASSEMBLE THE RAIL ONTO THE CABINET U BAR WITH SCREWS AT FRONT amp BACK USING MOVABLE NUTS z Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 22 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 6 EU PUSH THE UPS OR EBP INTO THE CABINET VIA THE RAIL FROM THE FRONT dii j Z mall um a ma mt T 3 ATTACH UPS OR EAR ONTO CABINET U BAR WITH SCREWS ON BOTH LEFT amp RIGHT SIDES Note Any external Battery Packs must be installed next to or under the UPS Please refer to Appendix A Battery Pack User Guide for more information when installing these Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 23 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS INITIAL CONNECTION AND STARTUP Ensure that the UPS and
20. The short circuit current capability of the battery is sufficient to burn wire or tools very rapidly producing molten metal Observe these precautions when replacing the battery Remove all watches rings or other metal objects Only use tools with insulated handles Do not lay tools or metal parts on top of battery or any terminals Wear protective eye wear goggles rubber gloves and boots Disconnect the charging source before connecting or disconnecting the battery terminals Qu M6 d ind Determine if the battery is inadvertently grounded If inadvertently grounded remove the source of the ground Contact with a grounded battery can result in electrical shock The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance applicable to a UPS and a remote battery supply not having a grounded circuit 7 ______________________ Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 28 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Remove plastic front cover Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 29 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 6029 0 0 0402 040 oO O O O 0 0 20 O O o Q OO oo oo ooo dara D O O O 250505040 WS WS CODO OO O0 o O D OU ORC aon na noa e 5 0 0 0 OOO OO e
21. XPC Corporation or a XPC Corporation authorized representative before or after delivery with regard to the use or application of Xtreme Power Conversion equipment is furnished on the basis that it represents XPC Corporations best judgment under the situation and circumstances but it is used at the recipient s sole risk EXCEPT AS STATED ABOVE XPC Corporation DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE EXCEPT AS STATED ABOVE IN NO EVENT WILL XPC Corporation BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF Xtreme Power Conversion EQUIPMENT including but not limited to any costs lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data cost of substitutes or claims by third parties Purchaser s sole and exclusive remedy for breach of any warranty expressed or implied concerning Xtreme Power Conversion equipment and the only obligation of XPC Corporation under this warranty shall be the repair or replacement of defective equipment components or parts or at XPC Corporations sole discretion refund of the purchase price or substitution of an equivalent replacement product Ii OII Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 38 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBL
22. ance ICES 003 This Class B Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment Regulations ICES 003 Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada Declaration of Conformity Request Units labeled with a UL mark comply with the following standards and directives e UL 1778 CAUTION shielded type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio or TV reception It is essential that only the supplied power cord be used Use only shielded cables to connect 1 0 devices to this equipment WARNING Any changes or modifications not expressly approved by the manufacturer of this device could void the user s authority to operate the equipment Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 5 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION UPS having Internal Batteries Risk of electrical shock Hazardous live parts inside this unit are energized from the battery supply even when the input AC power is disconnected CAUTION No User serviceable Parts Risk of electrical shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel CAUTION Non isolated Bat
23. ding computers workstations process control systems telecommunications systems sales terminals other critical instrumentation etc The purpose of the UPS is to protect these systems from poor quality utility power complete loss of power or other associated problems Electrical interference exists in many forms causing problems in AC power from lightning power company accidents and radio transmission motors air conditioners and vending machines Protection of sensitive electrical equipment is vital to protect against power outages low or high voltage conditions slow voltage fluctuations frequency variations differential and common mode noise transients etc To prevent power line problems from reaching critical systems causing damage to software hardware and equipment malfunctions the UPS maintains constant voltage isolating critical load output and cleaning the utility AC power Double Conversion On Line Technology A double conversion on line technology UPS provides completely isolated clean uninterrupted single phase power to your critical systems while maintaining the batteries for their maximum potential In the event that the power failure lasts longer than the UPS backup time the UPS will shut down avoiding battery damage When the input AC voltage returns the UPS will automatically return online to recharge the batteries As shown in fig 1 block diagram e An input filter reduces transients on the incoming utili
24. e OG O D G TOO OO O00 o o0 6 0 9 OOO IRI O O O CO OO O Remove the battery tray from the UPS ___ _ gt _ _ Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 30 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS TROUBLESHOOTING Issue The Input letters in the second row of the LCD are flashing The Input letters in the second row of the LCD are flashing Battery Indicator Flashing Utility Normal UPS has no AC input Insufficient battery run time UPS will not start after pressing the On Off button Major fault detection by the UPS Audible Alarm Two Beeps per second at startup for 8 total seconds One beep per 2 minutes One beep per second Once every 4 seconds in DC mode Constant beep Alarm Description The Input Voltage or frequency may be beyond the normal acceptable range Possible mis wiring AC line and neutral line Batteries are undercharged disconnected or need to be replaced Possibility that circuit breaker on UPS has tripped On batt displayed on LCD 1 Insufficient time for button depression 2 UPS has no battery connected 3 Battery voltage is too low to power the load 4 Fault has occurred inside the UPS Type of fault and fault code displayed on LCD Xtreme Power Convers
25. e for the correct operating system Follow the setup instructions Enter the product key when prompted The software key is found on the CD cover Click finish when prompted e The UPSILON icon will appear in the system tray of the desktop near the system clock Double click this icon to enlarge the program window Connect the RS232 cable included in the UPS packaging to the Computer and UPS Communication should start momentarily If it does not click on Settings up on the UPSilon toolbar then select a different Comport until communication is established Click on Manual in the UPSILON toolbar for further software configuration e NOTE PLEASE VERIFY AUTOMATIC SHUTDOWN TIME PARAMETERS IN THE SETTINGS SECTION FOR YOUR SPECIFIC INSTALLATION 7 Configure the optional NetAgentll SNMP card if installed Insert the NetAgent Utility CD included with SNMP packaging into a PC and download the user manual Install Netility from the AutoRun menu Connect a network cable from the PC to the SNMP Run Netility program and it will auto search and list available NetAgents SNMP card Highlight and click Configure to change the network settings on the NetAgent discovered e Disconnect the cable the PC and connect the SNMP to your network e Access the SNMP card via the network and make configuration changes using the manual downloaded previously e NOTE PLEASE VERIFY AUTOMATIC SHUTDOWN TIME PARAMETERS IN T
26. ed to an input voltage source The UPS has its own internal energy source Environment Ensure that all environmental concerns and requirements are met according to specifications listed in this document otherwise the safety of installation personnel cannot be guaranteed and the unit may malfunction Ensure that you remember the following when locating the UPS system and battery options Avoid extremes of temperature and humidity Maximum battery life can be attained with a recommended temperature range of 15 to 25 e Provide protection for the equipment from moisture e Space and ventilation requirements must be met Ensure there is 100mm behind and 50mm on the sides of the UPS for proper ventilation e Ensure that the front of the UPS remains clear for user operation _ lt lt Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 15 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Installation Standard brackets 4 Fj 2U 5IN 1 BRACKET FOR NXRT 1000 NXRT 1500 EBP1 amp EBP2 X k 3U 5 IN1 BRACKET FOR NXRT 2000 NXRT 3000 amp EBP3 Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 16 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 19 Cabinet Ear Installation NXRT 1000 NXRT 1500 NXRT EBP1 NXRT E
27. er for either the cost of repair of the Connected Equipment or the Fair Market Value of the damaged Connected Equipment up to the dollar limits stated above XPC reserves the right to require the Purchaser to transfer title and deliver the Connected Equipment to XPC if it chooses to reimburse the Purchaser for the fair market value of the Connected Equipment maximum liability shall be reduced to reflect all such other payments or sources of recovery whether applied for or not 4 f XPC issues payment to the Purchaser to have the Connected Equipment repaired the repair must be performed at a service center that is authorized by the manufacturer of the Connected Equipment XPC reserves the right to contact the authorized service center directly to discuss repair costs and damage to the Connected Equipment to determine if it was caused by a Power Disturbance and the right to request that the service center forward the Connected Equipment or components of the Connected Equipment to XPC for inspection 5 Unless modified in writing signed by an officer of XPC and the Purchaser the terms of this policy are the complete and exclusive agreement between the parties superseding all prior agreements oral or written and all other communications between the parties relating to the subject matter of this agreement No employee of XPC or any other party is authorized iz Xtreme Power Conversion XPC Corporation Rev 2
28. erly operated when a Power Disturbance passed through the Product and i exhausts the protection capacity of the Product or ii damages the Product 6 The Load Protection Policy does not apply if the Product has been operated in a failure mode or not in compliance with XPC operating instructions in the Product user s manual or if the Connected Equipment has not been operated in compliance with the instructions and manuals of its manufacturer vendor III Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 39 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS 7 This policy is null and void if XPC determines in its sole discretion that the Product has been tampered with or altered in any way What is Not Covered Under the Load Protection Policy The following damage is not covered by this Policy 1 Restoration of lost data and reinstallation of software 2 Damage from a cause other than AC power line transients except for damage due to telephone line Local Area Network or CATV transients which is covered only if the Product offers such protection DAMAGE CAUSED BY FAILURE TO PROVIDE A SUITABLE INSTALLATION ENVIRONMENT FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO LACK OF A PROPER SAFETY GROUND Damage caused by the use of the Product for purposes other than those for which it was designed Damage caused by accidents or natural disasters including but not limited to
29. follow up maintenance of the UPS and batteries Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 6 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS CAUTION The unit has a dangerous amount of voltage If the UPS indicator is on the unit s outlets may have a dangerous amount of voltage even when not plugged into the wall outlet because the battery may continue to supply power Care should be taken to undertake installation indoors free from electrically conductive particles which are under temperature and humidity control in order to reduce the risk of electric shock It is best to disconnect the device using the power supply cord Ensure that the equipment is placed in a position near the outlet where easily accessible Except for replacing the batteries all servicing on this equipment must be carried out by qualified service personnel Before conducting any maintenance repair or shipment first ensure that everything is turned off completely and disconnected For additional safety instructions please use the Safety Manual as a reference Special Symbols The following symbols used on the UPS warn you of precautions RISK OF ELECTRIC SHOCK Please observe the warning that a risk of electric shock is present CAUTION REFER TO OPERATOR S MANUAL Refer to the operator s manual for additional information such as important operating and maintenance ins
30. he UPS has fully charged batteries and the internal battery pack is connected e Assure that there is no AC input power source and or the unit is not plugged into an outlet e Press and hold the ON OFF button for three seconds e turned the UPS will perform a self test function when the yellow LED turns to green LCD displays On Batt the UPS is now functioning in DC mode Turning Off the UPS when in DC Mode e Press and hold the ON OFF button for more than 3 seconds to turn off the UPS This means the internal inverter has been deactivated rc SS SS Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 26 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS e During the shutdown period the UPS will run a self test Once the self test has been completed assuming there is still no AC input the LCD will no longer display information This indicates the UPS has no output Self Test Operation Please refer to the three operating buttons on the front panel of the UPS e Confirm the UPS is in Utility Mode e Press and hold the Function button for a minimum of two seconds e The self test will last for 10 seconds during this time the LED s will be lit in a sequential repeating fashion Audible Alarm silence in DC Mode or Fault Mode When the UPS is in DC Mode the audible alarm will sound every four 4 seconds Press and hold the Function Button for a mini
31. in its original packaging If the original packaging is no longer available as the Technical Support Technician about obtaining a replacement set of packaging material It is important to pack the UPS properly in order to avoid damage in transit Never use Styrofoam beads for a packing material 2 Include a letter with your name address daytime phone number RMA number a copy of your original sales receipt and a brief description of the problem 3 Markthe RMA number on the outside of all packages Xtreme Power cannot accept any package without the RMA number marked on the outside of the boxes 4 Return the UPS by insured prepaid carrier to the address provided by the Technician Refer to the Warranty statements in this manual for additional details on what is covered Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 37 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS XTREME POWER CONVERSIONS XPC CORPORATION LIMITED WARRANTY Xtreme Power Conversion XPC Corporation warrants Xtreme Power Conversion equipment when properly applied and operated within specified conditions against faulty materials or workmanship excluding batteries for a period of three years for NXRT Series products from the date of purchase XPC Corporation warrants internal batteries for a period of three years from the date of purchase For equipment sites within the United States and Ca
32. ion XPC Corporation Rev 2 7 13 What You Should Do Verify that utility voltage and frequency is within acceptable range If so contact support Check wiring of input to UPS reversed wiring etc Rewire if necessary Check UPS batteries If necessary reconnect batteries wait 12 hours to charge or replace defective batteries Reset circuit breaker 1 If batteries are undercharged let UPS charge batteries at least 12 hours 2 After charging if runtime is still insufficient replace with new batteries 3 Reduce output load to lengthen runtime 1 Depress the On Off button for at least three seconds 2 Make sure the batteries are connected and the connector on the battery cartridge is mated correctly 3 Plug the UPS in remove all loads and allow to charge for 12 hours 4 Contact dealer for service details Review abnormal process information table listed below in this manual and take appropriate action If problem does not resolve contact supplier for service and provide error code s Page 31 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS LCD FAULT CODES LNEMODE BATTEST MODE BUS FAULT ee 05 25 01 21 40 41 OVERHEAT 33 06 oB B __ OPSHRT 6 02 14 OVERLOAD B 060 45 FANFAUT _ 36 28 38 46 __ E Xtreme Power Conver
33. longer the batteries must be recharged for at least 36 hours every six months Extended Battery Pack Q amp A 1 Which EBP s do connect to an AC input source t is possible to plug in every into AC input source The more connected the faster the recharge time It is recommended that every third EBP be connected to incoming AC utility to properly charge the batteries in a complete system Leaving too many chargers connected may cause an over charge situation which could damage the batteries 2 Which LED s are supposed to be lit on the front of each EBP When is connected to an AC input source and the unit is charging a GREEN LED on the front of the EBP will be illuminated 3 Are any LED s on the front of the EBP supposed to be lit if it is not connected to an AC input source No The UPS and or the EBP s that are plugged into an AC input source are responsible for charging the entire system The EBP is still working and has the capability of providing DC voltage when needed No LED on the front bezel will be illuminated 4 The EBP is connected to an AC input source why does the LED on the front of the EBP turn ON and OFF intermittently and does this mean this EBP is not working e GREEN LED on the front of each indicates that the charger contained in the is charging Under certain conditions when the batteries are 10096 charged the charger in the EBP will shut off and the
34. mum of two 2 seconds to disable the audible alarm e When the UPS is in Fault Mode the audible alarm will continuously sound Press and hold the Function Button for a minimum of two 2 seconds to disable the audible alarm Ila II Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 27 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS BATTERIES The life of batteries used in these UPS products is estimated at 3 6 years depending on level of usage Once the battery is no longer useful and must be replaced please contact service personnel for assistance REPLACING THE BATTERY QUALIFIED SERVICE PERSONNEL ONLY CAUTION nead and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Service the battery under the supervision of Qualified Service Personnel knowledgeable of batteries and their precautions CAUTION use only the specified type of battery See your dealer for replacement batteries CAUTION rne battery may present risk of electrical shock Do not dispose of batteries in a fire as it may explode Follow all local ordinances regarding proper disposal of batteries CAUTION po not open or mutilate the batteries Released electrolyte is harmful to skin and eyes and may be toxic CAUTION Although the battery system voltage is only 12VDC and 24VDC the battery can present high risk of short circuit current and electrical shock
35. n the Optional battery packs if installed Connect the AC input cable to the UPS and connect the other end to an approved grounded outlet Once the UPS has been connected to an AC power source the internal charger will start charging the UPS batteries at this point the yellow LED is illuminated and the LCD displays UPS OFF In this state the output voltage is zero which means UPS has no output Please realize that although you may start using the UPS immediately maximum back up time will still not be available so it is recommended to charge the batteries for a minimum of 6 hours before use 5 Start and configure the UPS On Off Button Function Button Inquiry Button Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 24 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS e Press and hold the ON OFF button for more than 3 seconds to turn on the UPS The UPS should now start its inspection of the internal functions main synchronization and inverter startup Then power should start to be supplied via the outlets Once turned on the UPS will perform a self test function when the yellow LED turns to green LCD displays on line and means UPS is working in utility mode 6 Configure the local monitoring software if desired e Insert the UPSilon 2000 CD included with UPS packaging into the CD ROM of the local computer e Select Install program from the Autorun menu and choos
36. nada this warranty covers repair or replacement at the sole discretion of XPC Corporation The customer is responsible for the costs of shipping the defective product to XPC Corporation XPC Corporation will pay for ground shipment of the repaired or replacement product This warranty applies only to the original purchaser If equipment provided by XPC Corporation is found to be Dead on Arrival DOA XPC Corporation will be responsible for the costs of shipping product to and returning equipment from the customer in a timely manner as agreed to with the customer once the customer has requested and received a Return Material Authorization RMA number DOA equipment is defined as equipment that does not properly function according to user documentation when initially received and connected in conjunction with proper procedures as shown in the user documentation or via support provided by XPC Corporation personnel or authorized agents This warranty shall be void if a the equipment is repaired or modified by anyone other than XPC Corporation or a XPC Corporation approved third party b the equipment is damaged by the customer is improperly used or stored is subjected to an adverse operating environment or is operated outside the limits of its electrical specifications or c the equipment has been used or stored in a manner contrary to the equipment s operating manual intended use or other written instructions Any technical advice furnished by
37. onnected equipment does not exceed the maximum VA rating for the UPS The maximum VA ratings are shown in the Specifications section of this document 2 Ensure that the equipment plugged into the battery powered outlets does not exceed the UPS rated capacity If UPS rated capacities are exceeded an overload condition may occur and cause the UPS to shut down and trip the circuit breaker 3 If the power requirements of your equipment are listed in values other than Volt Amps convert Watts W or Amps A into VA by doing the calculations below Note The equation below only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at any given time Users should expect usage requirements to be approximately 6096 of the value to estimate power requirements Watts W x 1 43 VA or Amps A x 120 VA Add the totals for all of the equipment and multiply this total by 0 65 to calculate actual power requirements Note Many factors can affect the amount of power that your computer system will require The total load that you will be placing on the battery powered outlets should not exceed 8596 of the UPS capacity HARDWARE INSTALLATION GUIDE Inspect the UPS upon receipt The packaging is recyclable keep it for reuse or dispose of properly Safety Information Information presented here is vital to all personnel Please read all Safety information Storage and Transportation
38. operating systems It can support operating systems such as HP Open View IBM Netview SUN Netmanager etc This enables the UPS to provide instant UPS and power information over the network Please contact your reseller for additional details Notes The UPS can be monitored through the RS232 interface or the SNMP card but only one way at a time The user can choose RS232 or SNMP communications through the communications switch on the rear panel of the UPS RS232 is chosen if the switch is depressed to the RS232 position and SNMP is chosen if the switch is depressed to the SNMP position When there are two or more monitored pieces of equipment the ground of each piece of equipment should be shared The SNMP card is configured as DHCP by default IP setting cv rnn Yr Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 13 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Remote Emergency Power Off Port A customer supplied switch located remotely can be used to close the REPO connection and allows the UPS output receptacles to be switched off Since the REPO shuts down the equipment immediately orderly shutdown procedures are not followed by any power management software The UPS will have to be manually restarted in order to regain power to the outlets on the UPS DETERMINING THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Make sure the total Volt Amp VA requirements of your c
39. optional battery packs are mounted correctly and the UPS is disconnected from input power before proceeding 1 Connect external battery packs option CAUTION CONNECT ONLY BATTERY PACKS PROVIDING THE SAME DC VOLTAGE AS THE UPS PLEASE DOUBLE CHECK LABELING ON THE UPS AND BATTERY PACKS TO ASSURE PROPER VOLTAGES ARE CONNECTED CONNECTING THE INCORECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS AND OR BATTERY PACK THAT WILL VOID THE WARRANTY Ensure that the UPS is disconnected from input and is off while connecting the External Battery Packs Ensure all battery breakers are in the OFF position e Remove the covers on the UPS and Connect the battery cable that comes with the External Battery Pack between the External Battery Pack to the UPS e Secure the DC battery cable to the rear of the UPS and the rear of the by using x 8 screws provided 2 each per connector end Connect the 5 15P from the to input AC utility source per specifications Connect a second battery pack to the first in the same fashion if more than one is to be installed e Refer to Appendix A Battery Pack User Manual for more details 2 Connect SNMP card option Remove the two screws securing the SNMP cover plate on the rear of the UPS and slide the SNMP NetAgentll card into the slot Secure the card into the slot with the two screws previously removed 3 Close the battery breakers o
40. or of XPC Products The Purchaser of this Product is protected for the term of the XPC Limited Warranty against certain losses caused by a Power Disturbance for properly connected electronic equipment referred to as the Connected Equipment subject to certain terms and conditions provided below This policy applies only to the original purchaser of the Product If the Product is transferred or sold to another person or entity this policy is void Load Protection Policy Dollar and Period Limits For purchasers that meet the qualifications and conditions set forth in this policy XPC will provide reimbursement cost of repair or fair market value as determined by during the period limits and up to the dollar limits stated as follows NXRT 50 000 Term of XPC Limited Warranty P80 50 000 Term of XPC Limited Warranty P90 50000 Term of XPC Limited Warranty This Load Protection Policy is not deemed first dollar coverage XPC s obligation is reduced by any amounts that the Purchaser is entitled to recover from other sources regarding the Connected Equipment including but not limited to insurance other warranty extended warranty or legal liability regardless of whether or not the Purchaser makes a claim for recovery Eligibility for Coverage Under the Load Protection Policy 1 The Product must be registered on the XPC website www xpcc com within 10 days of purchase All required information must be provided and Purchaser
41. plier for the location of the Connected Equipment XPC will forward to the Purchaser a Load Protection Policy claims form which must be completed and filed with XPC within 30 days a Mark the Load Protection Policy number on the Product the Purchaser is returning b Pack the Product in its original packaging or similar packing materials if the original packaging has been discarded Enclose the completed Load Protection Policy claim form and a copy of the Purchaser s original sales receipt for the Product in the box c Mark the RMA number clearly on the outside of the box d Ship the Product one way shipping charges paid by the Purchaser to XPC Corporation 230 Yuma Street Denver CO 80223 Attn LPP RMA 3 XPC will evaluate the Product to determine its level of functionality and will examine the Product for evidence of damage from a Power Disturbance a f XPCs evaluation provides no evidence of damage from a Power Disturbance XPC will send to the Purchaser i a report summarizing the tests performed and ii a rejection of claim notice b If the Product shows evidence of damage from a Power Disturbance XPC will request that all Connected Equipment for which a Load Protection Policy claim has been submitted be sent for evaluation to either XPC or an authorized service center If it is determined that the Connected Equipment has been damaged by a Power Disturbance XPC will in its sole discretion issue payment to the Purchas
42. port personnel can more effectively assist you Cr Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 4 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS EMC Statements FCC Part 15 Notice Pursuant to section 15 of the rules this product has been tested and thereby complies to the conditions of a Class B NXRT 1000 NXRT 1500 and Class A NXRT 2000 NXRT 3000 digital device which have been established for offering sufficient protection against dangerous interference for installation in a residential area Installation and use of the equipment should comply with the instructions provided in order to avoid such interference due to the amount of radio frequency energy that is radiated and generated by the equipment In spite of this we cannot assure that a certain amount of interference may not occur in some installations If by turning on and off it can be deduced that your radio or television reception is found to be influenced by harmful interference from the equipment it is recommended to use one of the following preventive measures e Place the receiving antenna in a separate location or orientation e Ensure a greater distance is achieved between the receiver and the equipment Ensure that your equipment is connected to an outlet on a separate circuit than the receiver e Contacta technician experienced with radio and TV or a dealer for further assist
43. should retain a copy for Purchaser s records When registering on the website Purchaser must list all connected equipment that is directly connected to the product Only those devices registered in that manner will be covered 2 All Connected Equipment must be UL or CSA approved 3 The Product must be plugged into a properly wired and grounded outlet Use of input surge devices extension cords adapters ground wires or electrical connections not manufactured by XPC voids the XPC Load Protection Policy No other surge protection device may be connected to the output sockets of the Product The installation must comply with all applicable electrical and safety codes set forth pursuant to the NEC 4 The Product must have undeniable physical evidence of a Power Disturbance that directly and proximately caused the damage 5 The Connected Equipment must have been damaged by a Power Disturbance on a properly installed grounded and National Electric Code code compliant 120 208 240 Volt AC power line in the United States or Canada by a Power Disturbance on standard telephone land line or PBX telephone equipment line that is properly installed and connected to an RJ11 port on the Product or by a Power Disturbance on a standard Local Area Network connection that is properly installed and connected to an RJ45 port on the Product and d is directly plugged into and properly connected to the Product in its original condition which was prop
44. sion XPC Corporation Rev 2 7 13 Page 32 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS SPECIFICATIONS mmm emm 120 VAC 80 138V at 100 load 60 138V at 40 load Linear lt 596 non Linear lt 10 ULU EL mese mz oxm w Overload Capacity 110 150 for 30 sec gt 150 for 200 msec Crest Factor 3 1 at full load Battery UPS 3 12V 9 36 4 12V 7 2 AH 48V 8 12V 7 2AH 96V Backup Time 7 11 min internal batteries to 18 hours using External Battery Packs EBP Battery Type EBP E us da An d 2 strings of 8 12V 7 2 AH 96V Recharge Time 8 hours to 9096 E Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 33 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS waran _ 17 3 x 17 7 x 3 4 17 3 x 25 6 x 3 4 17 3 x 21 7 x 5 2 usimerermrimenr mexmexne orm oem _ _ _____ s 1 NEMA L5 20R 1 NEMA 15 308 Receptacles v Tort 4 5 20R 4 NEMA 5 20R Communication RS 232 or SNMP optional card Interface Included in box UPSILON CD horizontal brackets 5 1 brackets manual 6ft DB9 cable ENVIRONMENT Operating 0 40 32 10437 Temperature Audible Noise lt
45. tery supply Risk of electric shock battery circuit 15 not isolated from AC input hazardous voltage may exist between battery terminals and ground Test before touching WARNING Fuses To reduce the risk of fire replace only with the same type and size of fuse WARNING I unit intended for installation in a controlled environment CAUTION po not dispose of batteries in a fire the battery may explode CAUTION po not open or mutilate the battery released electrolyte is harmful to the skin and eyes CAUTION A battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries Remove watches rings or other metal objects e Use tools with insulated handles To reduce the risk of electric shock disconnect the UPS from the main supply before installing a computer interface signal cable Reconnect the power cord only after signaling interconnections have been made Servicing of batteries should be performed or supervised by personnel with knowledge of batteries and the required precautions Keep unauthorized personnel away from batteries These UPS units are extremely heavy Do not install the UPS in a rack or enclosure by its front two ears only Adjustable rack rails are required for this type of installation The instructions contained within this safety manual are deemed important and should be closely followed at all times during installation and
46. tructions SAFE GROUNDING TERMINAL Indicates primary safe ground LOAD ON OFF Pressing the button turns on off the output receptacles and the indicator light RJ45 RECEPTACLE The receptacle provides network interface connections and telephone or telecommunications equipment should not be plugged into it Please do not discard of the UPS or the UPS batteries as the UPS may have valve regulated lead acid batteries Please recycle batteries appropriately 4 Qe Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 7 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS INTRODUCTION The information provided in this manual covers single phase 1000 3000 VA uninterruptible power systems their basic functions operating procedures options available and emergency situations It also includes information on how to ship store handle and install the equipment Only detailed requirements of the UPS units are described herein and installation must be carried out in accordance with this manual Electrical installation must also carefully follow local legislation and regulations Only qualified personnel should conduct these installations as failure to acknowledge electrical hazards could prove to be fatal PRODUCT DESCRIPTION Many different kinds of sensitive electrical equipment can be protected by an Uninterruptible Power Supply UPS inclu
47. ty maintain full battery charge the AC input power is rectified and regulated in the rectifier feeding power to the battery converter and inverter DC power is converted to AC in the inverter passing it on to the load e Power is maintained from the battery during a power failure e The converter increases voltage appropriately for the inverter Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 8 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS By pass Filter Rectifier Inverter Filter 4 Monitoring DC DC panel Battery Converter Control 8 75232 m Charger amp Monitoring battery Figure 1 Block Diagram Diagnostic Tests When the UPS is started a diagnostic test is automatically executed checking the electronics and batteries reporting any problems on the LCD display A diagnostic test can also be performed manually from the front panel at any time SYSTEM CONFIGURATION The UPS device and the internal batteries make up the system Depending on the site and load requirements of the installation certain additional options are available for the solution Planning a UPS system the following should be taken into consideration The total demand of the protected system shall dictate the output power rating VA Allow margin for future expansion or calculation inaccuracies from measured
48. us and or operation Line information will be described from top to bottom with the top being line one Line One Provides data in to numeric sections with the data corresponding to the applicable category in line one and two Line Two Allows the user to identify which variable information is being displayed Input e Output e Battery e Load e Temperature Line Three This is a graphics section with load graphics on the left and battery graphics on the right The failure icon will appear in this section when a failure occurs Xtreme Power Conversion XPC Corporation Rev 2 7 13 Page 12 NXRT 1000 NXRT 1500 NXRT 2000 NXRT 3000 USER S MANUALUNINTERRUPTIBLE POWER SUPPLY UPS Line Four This indicates the status of the UPS e ONLINE utility mode ON BATT battery mode ON BPS bypass mode UPSOFF standby mode RS 232 Standard Interface The RS 232 interface uses a 9 pin female D sub connector Information provided includes data about utility load and the UPS The interface port pins and their functions are identified in the following table GOGO PIN FUNCTIONS 1 4 6 7 8 NOT USED 9 _______ REMOTEWAKEUP CAUTION MAX RATED VALUES 12VDC SNMP Communications Option The UPS provides an intelligent slot for internal or external network card This special intelligent network card can be compatible with popular software and hardware found on the web and in
Download Pdf Manuals
Related Search