Thanks for purchasing “SEAKING” series Electronic Speed
Contents
1. then the cutoff threshold of this battery pack is 3 2 3 9 6V 2 Program the ESC with the Program Card c If you are using NiMH or NiCd battery Program card is an optional equipment for boat ESC it has 3 digital LEDs to show the programmable items and their NiMH and NiCd battery are not easy to be damaged usually you needn t worry about the over discharge values so the user interface is very friendly It is quite easy for programming the ESC with this small equipment Please problem so you can set this programmable item to No Protection read the user manual of program card for more information 4 Timing Please select the most suitable timing value according to the motor you are just using The correct timing Trouble Shooting value makes the motor running smoothly And generally higher timing value brings out higher output power and S higher speed Trouble Possible Reason Action After power on motor does not work no The connection between battery pack Check the power connection Program the ESC sound is emitted and ESC is not correct Replace the connector 1 Program the ESC with you transmitter After power on motor does not work Input voltage is abnormal too high or Check the voltage of battery pack 4 Steps Enter program mode Select programmable item Choose the new value of the selected item Exit such an alert tone is emitted too low beep beep beep beep STEP 1 Enter the program mode Every beep2. beep has a time interval of about 1 second Switch on the transmitter move the throttle stick to maximum position Full throttle position and then After power on motor does not work Throttle signal is irregular Check the receiver and transmitter connect the battery pack to the ESC such an alert tone is emitted Wait for 2 seconds the motor emits Beep Beep tone beep beep beep Every beep has a time interval of about 2 seconds aE Teo Se Come MOTENE gtp epee ane tial Wed istic progran MECE Semele The motor runs in the opposite direction The connection between ESC and Swap any two wire connections the motor need to be changed between ESC and motor The boat cannot run backward The ESC is not set to Forward and Program the ESC correctly STEP 2 Select the programmable item Backward running mode Calibrate the throttle range again You will hear 4 groups of Beep tone circularly If you move the throttle stick to bottom position or the neutral The ESC cannot recognize the according to the instructions on neutral point of throttle channel page 1 poems ann pee CONCS ater One ele Opes hier Nein neces After power on motor does not work a Direction of the throttle channel is Set the direction of throttle channel 1 Beep Running Mode special tone J 56712 is emitted after 2 reversed so the ESC has entered correctly Beep Beep Lipo Cells beep tone Beep Beep the program
3. correctly please always use a fully charged battery to connect the ESC If the battery is Woet One lone Dop 5 short Seep Freno Deien bno mein fa Nae ee 2o partly discharged the Auto Calculate may get a wrong result Hint In the startup process the motor will emits several Beep tones to represent the Lipo cells number it is helpful for you to check whether it is coincident with the actual battery pack or not 3 Low Voltage Cutoff Threshold This function prevents the lithium battery pack from over discharging The ESC STEP 4 Exit program mode detects the battery s voltage at any time if the voltage is lower than the threshold for 2 seconds the output power There are 2 methods to exit the program mode will be reduced 50 Please replace the battery pack as soon as possible _ 1 In Step 3 after choosing the value the motor will emits special tone JSisis move the throttle stick to the a Warning If you ignore the low voltage cutoff phenomenon and keep running the battery pack will be damaged re b How to calculate the cutoff threshold of a whole battery pack bottom position or the neutral position in 2 second to exit the program mode The cutoff threshold of a battery pack The threshold of each cell cells number 2 Disconnect the battery pack from the ESC to exit the program mode forcibly For example if the threshold of each cell is set to 3 2V Cell and the battery pack is 3S 3 Cells
4. 2 HW SM701DUL 20130627 Page 1 1 Disconnect the two bullet connectors on the positive input wire red color thick of the ESC 2 Connect battery wires 3 Connect the bullet connectors on the positive input wire red color thick of the ESC as soon as you hear the special tone 3123 STEP 2 Throttle Range Setting Throttle Range Calibration In order to make the ESC fit the throttle range you must calibrate it for the following cases otherwise the ESC cannot work properly gt Begin to use a new ESC gt Begin to use a new transmitter gt Change the settings of neutral position of the throttle stick ATV or EPA parameters etc 2 1 Turn on the transmitter set the EPA ATV value of throttle channel to 100 and disable the ABS brake function of your transmitter if it does has this function If you are using a Futaba transmitter please set the direction of the throttle channel to REV 2 2 If you are using a Flat style transmitter a Move the throttle stick to the top position that is full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone can be heard that means the full throttle position has been confirmed 2 2 If you are using a Handgun style transmitter a Move the throttle stick to the maximum position that is full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone ca
5. User Manual of SEAKING Series Brushless Speed Controller for Boat Thanks for purchasing SEAKING series Electronic Speed Controller ESC for boat High power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the correct use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses or costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation to compensation is limited to the invoice amount of the affected product Features Specially designed for RC boat with excellent start up acceleration and linearity features Use top quality electronic components to enhance the current endurance ability of the ESC With water cooling heat sink the ESC is splash proof Note Not 100 water proof 2 running modes Forward Only mode and Forward Backward mode for various of boats Multiple protection features Low voltage cut off protection for lithium or nickel battery Over heat protection Throttle signal loss protection 8 steps of timing adjustment compatible with all kinds of sensorless brushless motor Pocket sized Program Card can be purchased separately for easily set
6. le Items in the following form is set to No protection this is only suitable when you are using a NiMH battery pack Please never use No protection mode for lithium battery otherwise the battery is very easy to be damaged 4 Move the throttle stick upwards the motor begins to run and speeds up The LED Status There is a red LED in the ESC the usages are 1 The LED lights when the throttle stick is moved to the maximum position full throttle 2 When setting the throttle range or setting the programmable items of the ESC the LED flashes at the same time when the motor beeps User Manual of SEAKING Series Brushless Speed Controller for Boat HW SM701DUL 20130627 Page 2 Programmable Items Note2 The italics texts in the following form are the default settings STEP 3 Choose the new value for the selected item After entering an item you will hear several tones in loop Set the value matching to a tone by moving the throttle stick to the maximum position Full throttle position when you hear the tone then a special tone sisis emits means the value is chosen and saved in the ESC Keep the throttle stick at the maximum position Full throttle position you will go back to step 2 and you can select other items Move the stick to bottom or neutral position within 2 seconds will exit program mode directly Value Programmable Items 2 3 4 5 6 7 8 1 Running Mode WNote3 Forward Onl Forward and y Back
7. mode 2 3 Beep Beep Beep Low Voltage Cutoff Threshold The motor suddenly speeds down even The ESC has entered the low voltage Replace the battery pack as soon if at the full throttle situation cutoff protection mode as possible 4 Stop running the boat for several The ESC is over heat minutes to cool the ESC Beep Beep Beep Beep Timing
8. n be heard that means the full throttle position has been confirmed b Release the throttle stick to the neutral position a Beep tone can be heard that means the neutral position has been confirmed Now the throttle range setting process is finished b If you want to set it to half range please move the throttle stick to the neutral position a Beep tone can be heard that means the neutral position has been confirmed If you want to set it to full range In such a case the boat cannot run backward please move the throttle stick to the bottom position a Beep tone has been confirmed Hh DN can be heard that means the bottom position Now the throttle range setting process is finished Beep Beep p Note When the motor emits Beep tone the red LED dhe i in the ESC will flash at the same time Beep Beep Beep Note When the motor emits Beep tone the red LED in the ESC will flash at the same time The Normal Start Process 1 Move the throttle stick to the neutral position or the bottom position and then turn on the transmitter 2 Connect the battery pack to the ESC 3 The motor emits several Beep tones to represent the cells number of your lithium battery pack Please make sure that the number is correct If only one Beep tone is emitted that means the Low Voltage Cutoff Threshold Please refer to the Programmab
9. ting the programmable items Note1 The program card is an optional equipment for the ESC YV vVVVVY Specifications Model Cont Current Current Burst BEC BEC Battery Cells Water Mode Output Lipo NiMH Cooling E3 Pipe 35 5 3 5 3 Weight Normal ESC Supports 2 6 cells Lipo 10 60 90 40 48 35 20 48 35 20 5 8V 3A High Voltage ESC Supports 5 12 cells Lipo 80A HV_ SEAKING 80A HV 160A 94 33 18 182g 88 58 23 130A HV SEAKING 130A HV 130A_ 180A None None _ Begin To Use The New ESC Warning For safety please always keep the propeller away from human body or any other object STEP 1 Connect the ESC motor receiver battery and servo according to the following diagram Picture 1 The output wires of A B C of the ESC can be connected with the motor wires freely without any order If the motor runs in the opposite direction please swap any two wire connections Brushless Motor fo Mian Battery pole Connect to throttle TAP ZA ibe Black wire channel HU ff Ch 2 _ Battery pole Red wire Receiver Picture 1 Picture 2 The SEAKING 80A HV SEAKING 130A HV use the new anti spark structure There are a pair of bullet connectors and a thin red wire attached with the positive input wire red color thick of the ESC They are used to eliminate sparks when the battery pack is connecting with the ESC Please use it in the following sequence See picture
10. ward 7 2 Lipo Cells Note4 ee 2 celis 3celis 4 cells 5cels 6cels Note5 Auto Calculate 10 cells 12cells f 3 Low Voltage Cutoff Threshold No Protection 2 8V Cell 3 0V Cell EZAYI 3 4v cen o Note3 Seaking 130A HV only has option 1 Forward Only it hasn t option 2 Forward and Backward Teon Beep Snor Seepa cnong enon pieng Note4 The parameters in this line are available for normal voltage ESC Supports 2 6 cells lipo Items Beeps Beeps Beep Note5 The parameters in this line are available for high voltage ESC Supports 5 12 cells lipo 1 Running Mode With Forward Only mode the boat can go forward but cannot go backward Forward and Backward Backward mode provides backward function which is suitable for some specially designed boats Please read the Lipo Cells Auto Calculate 2 Cells 3 Cells 4Cells 5Cells 6 Cells user manual of your boat to confirm whether it is possible to run backward i i Low Voltage No Protection 2 8V Cell 3 0V Cell 3 2v Cell 3 4V Cell 2 Lipo Cells We strongly suggest setting the Lipo Cells item manually If you choose Auto Calculate the ESC will measure the battery s voltage when it is just connected and then the ESC judges the cells number For Cutoff Threshod example if the battery s voltage is lower than 8 8V it will be judged as 2 cells Lipo battery In order to let the ESC Timing oe ee fo 75 11 25 io 18 75 judge the cells number
Download Pdf Manuals
Related Search