Push button Transmitter Device - PTM 200: User Manual
Contents
1. held remote controls with up to 4 single pushbuttons Because the RF transmitters are self powered no batteries maintenance free RF systems are possible 1 3 Technical Data Power supply power generation by rocker operating Electrodynamic Power Generator Antenna external whip antenna 26 8 cm 21 3 9 1mm Frequency Transmission power 315 0 MHz typ 3 dBm at antenna input Data rate Modulation type 125 kbps ASK Channels 2 with 4 action states each upper lower pushbutton is pressed released Telegram type RPS of type 2 allows interpretation of operating two buttons simultaneously Transmission range 300 m free field typ 30 m indoor Telegram packet length sub telegram 0 7 ms 5 Number of channels 2 channels with action states each upper lower contact nipple is pressed released Device identifier individual 32 bit ID factory programmed No of redundant packets 3 5 depending on residual energy 3 packets within about 20 ms delay effected at random 1 4 Mechanical Interface Module dimensions inclusive rotation axis and energy bow 40 0 x 40 0 x 11 2 mm Device weight 20gtig Energy bow travel operating force 1 8 mm approx 7 N at room temperature only one energy bow may be actuated at the same time Restoring force at energy bow 0 5 Nto 4 N For the correct function of the application the specified minimal restoring force of 0 5 N must be considered Number of operations typ 50 000 actuations tested accordin2. 2 dimensions of rocker part Figure 5 PTM 200C without antenna cut B and C EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 7 22 USER MANUAL Green Smart Wireless enocearn 36 440 15 antenna labeling area 4020 1 Hatched areas support planes Figure 6 PTM 200C with antenna rear view EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 8 22 USER MANUAL Green Smart Wireless enocean catwalks of switch rocker press bow to stopper 2 dimensions of rocker part Figure 7 and 8 PTM 200C without antenna side view If the rocker is not mounted on the rotation axis of PTM 200C several tolerances have to be considered The measure from support plane to top of the energy bow is 7 70 mm 0 3 mm The movement of the energy bow must not be limited by mounted rockers Catwalks of switch rocker must not exert continuous forces on contact nipples gt gt gt EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 A
3. Convenient equipment case 120V wall power supply Field Intensity Meter EPM 100C The EPM 100C is a mobile field intensity meter that helps the engineer to find the best in Stallation positions for sensor and receiver It can also be used to check disturbances in links to already installed equipment The EPM 100C displays the field intensity of received radio telegrams and interfering radio signals in the 315 MHz range The simplest procedure for determining the best installation positions for the radio sensor receiver Type Person 1 operates the radio sensor and generates pushbut ton radio telegrams Person 2 checks the received field intensity on the meter dis play to find the optimal installa tion position EnOcean Ordering Code EPM 100c 53034 3100 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 21 22 USER MANUAL Green Smart Wireless enocearn 5 PATENT PROTECTION PTM 200C is protected by the following patents US 6 747 573 US 7 019 241 Further patents pending EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 22 22
4. DDIICOLIOL Svar cece ec red rU DK EUIS oa a EPDUr FUP EPRE RM PRU rUU Costi pa KR 5 1 3 Irene Daal erna a A E AEA 5 1 4 Mechanical IMET ACS rautvaagraaeveaeveaareanruaeveaeveauvenniiayveaevaaue ania enereaurean ran ENA 5 1 5 Environmental CONAN S esses paa exu MEER ENRUPITOSUHE REIN AAE ANa 10 1 6 PECTIN r O earrannan Er EEEE E tim Cir tiU e DrF eee PDKP CEPI 10 2 FUNCTIONAL DESCRIPTION s vestitetvbIv TRE ROUND PDT UR RESP I cta TuS adapt RIE nS 10 2 1 BOE DIA OI sccurawawent aos E E IDA U QUI KM MXN EN MRUMN KM IPENMEISCEEMMEESMS 10 2 2 Contact Nipples Designation sgennctencsipiid bu pasta vid Part DPI INTUS Dita Pm VI EROR DIM NU 11 2 3 PIN 200C Radio VECO dbi ccna china ta ceat rac v Rr UrKOI KEY FEE dx ptura Sod ur Eo sete U CEP 12 2 3 1 FPRCOUCIIC M EON im IET TU IT UITTUEUTUIETTLTTDET 12 2 3 2 Mlesitiz iesus N T t EAE E E A EEA E AREA 12 2 329 TPAS SONNEN Tem TT T DL LUTMTUTTTUEUEUTUECTT 12 2 3 4 Reliable radio transmission within systems operating many sensors 13 3 APPLICATIONS INFORMATION 5etaaes oras V3 adATRaX x aaa eux eaadan dA a TOR SFR Ha dRO rinii nininini 14 3 1 Lavinga tme COM a vicars nau AE teas RARE NN TNVEXMER SEEN EI NM PENMDIICE MMIMME 14 3 2 Construction of application specific Switch Rockers eeeeennn m n nnn 15 3 3 DEVICE ROUN IO acest 2 09pdtved sou dua DM METEO Va NUUS UPEeD Mad a ME MUNUU UE SUN DRIED WIDE UpUU EE 15 3 4 Transmission Rardessessaois unies ds 215304309929 0209 133993 90d e
5. L Figure 10 Contact nipple designation Radio signals of the PTM 200C device are event controlled energy bow is pressed released with contact nipple code channel state and unique device identification fixed 32 bit ID When operating more than one nipple at the same time note that PTM 200C sends multiple button code combinations Note N message One or two contact nipples have been pressed when activating the energy generator gt Message with nipple code and pressed released event status of the energy bow is sent U message No contact nipple was pressed when activating the energy genera tor or 3 or 4 nipples have been pressed gt Message with pressed released event status of the energy bow is sent and the information if either none or more than two nipples have been pressed Note that it can t be differentiated if 3 or if 4 nipples have been pressed Due to the mechanical hysteresis of the energy bow in most rocker switch device implementations pressing the rocker sends an N message and releasing the rocker sends a U message EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 11 22 USER MANUAL V1 11 Green Smart Wireless PTM 200C enocearr 2 3 PTM 200C Radio Telegram For the transmission of the telemetric signals EnOcean has
6. M Germany www enocean com Page 9 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C 1 5 Environmental Conditions Operating temperature 25 C up to 65 C Storage temperature 25 C up to 65 C Humidity 0 to 95 r h 1 6 Ordering Information Type Ordering Code PTM 200C S3031 A200 2 FUNCTIONAL DESCRIPTION 2 1 Block Diagram Data Processor Contact Nipples Ant Pushed Released DC Power Power Converter Figure 9 Block diagram of PTM 200C Energy Bow Power Generator Converts pressure on the energy bow into electrical energy Power Converter Electronic converter unit for generating the device DC power supply EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 10 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C Processor Converts the contact nipples status and pushed released data from the power generator into a reliable and energy efficient serial telegram structure HF transmitter Sends the data in the form of a series of short radio signals 2 2 Contact Nipples Designation With 4 contact nipples the PTM 200C offers 2 channels with 4 action states each up per lower nipple is pressed released when activating the energy bow The nipples designa tion is as follows CHANNE
7. Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 16 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C 3 5 FCC IC Approval Requirements This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada If this device is operated in compliance with the following requirements it can be operated without notification and free of charge in the area of the United States of America and in Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Trade Name PTM 200C Model No PTM 200C FCC ID SZV PTM200C IC 5713A PTM200C This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interfe rence that may cause undesired operation Warning Changes or modifications made to this equipment not expressly approved by EnOcean may void the FCC authorization to operate this equipment This equipment has been tested and found to comply with the limits for a Class B digital de vice pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection a
8. Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 17 22 USER MANUAL Green Smart Wireless enocearn TCB CUAUTHORZATION TCB Certification Issued Under the Authority of the Federal Communications Commission By CETECOM ICT Services GmbH ae Untertuerkheimer Strasse 6 10 AVE al D 66117 Saarbruecken Germany Application Dated 07 24 2007 EnOcean GmbH Kolpingring 18a Oberhaching 82041 Attention Armin Anders Director Product Marketing NOT TRANSFERABLE EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE and is VALID ONLY for tha equipment identified hereon for use under the Commission s Rules and Regulations listed below FCC IDENTIFIER Name of Grantee Equipment Class Part 15 Security Remote Control Transmitter Notes Pushbutton Transmitter Frequency Output Frequency Emission Grant Notes FCC Rule Parts Range MHZ Watts Tolerance Designator 15 231 315 SSS RES zm COMM fU Lh X we OM A tti wta EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 18 22 USER MANUAL EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany CETECOM ICT Services GmbH Untert rkheimer Strasse 6 10 D 66117 Saarbr cken Germany Conformity Assessment Body Cer
9. USER MANUAL Green Smart Wireless enocearn October 6 2011 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany WWW enocean com Page 1 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C REVISION HISTORY The following major modifications and improvements have been made to the first version of this document No Major Changes V1 01 Note added in chapter 1 4 Movement of energy bows must not be limited by mounted rockers V1 02 Section 3 6 Japanese Type Approval added Recommendation for rocker material modified in chapter 3 2 V1 11 No continuous forces on contact nipples allowed Remark added in 1 4 Published by EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany www enocean com info enocean com phone 49 89 6734 6890 EnOcean GmbH All Rights Reserved Important This information describes the type of component and shall not be considered as assured characteristics No responsibility is assumed for possible omissions or inaccuracies Circuitry and specifications are subject to change without notice For the latest product specifications refer to the EnOcean website http www enocean com As far as patents or other rights of third parties are concerned liability is only assumed for modules not for the described a
10. aa Toda qudd PP PREND PE a naa 16 3 5 FCC IC Approval Reddit ermellbS ivacavanatece xpu VER EROR REUNIR NU RN ARD EATER QUE E DN EY 17 3 6 Japanese Type ADDO Val csnentisms amis Pate mE euDRMITU CM PMID RC UI PII CM US UM 20 4 DEVELOPMENT FOOL irrien mood atti v EE SEXO Pix PC a der ENAA NEA 21 4 1 Eyaluation KIC EYA ic UEM 21 4 2 Field Intensity Meter EPM 100C s ssssssssssssssssssssssnnsssnnsssnnsssnnssnsnssnsnennsnennesenne 21 5 PATENT PROTECTION 2axiatesemassiatdeua pO EE E A US art inu DN eU Beta DE 22 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 3 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C 1 GENERAL DESCRIPTION The radio transmitter device PTM 200C from EnOcean enables the implementation of wireless remote controls without batteries Power is provided by a built in elec tro dynamic power generator The PTM 200C device serves the 315 MHz air interface protocol of EnOcean Together with the receiver device RCM 130C this device can be easily integrated in operation and control units for the implementation of different application specific system solutions 2 Contact nipples for switch rocker identification 1 Energy bow on both device sides Rotation axis for pushbuttons or switch rocker Figure 1 Electro dynami
11. apply teflon varnish in the areas of actuation Please note that the rockers should be of nonmetal for best transmission range Please also avoid plastic materials with conducting ingredients like graphite 3 3 Device Mounting For mounting the PTM 200C device into an application specific case the package outline drawings of the device are roughly dimensioned in chapter 1 4 If more detailed dimension ing data of the PTM 200C device case is necessary 3D construction data is available from EnOcean IGS data EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 15 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C 3 4 Transmission Range The main factors that influence the system transmission range are Type and location of the antennas of receiver and transmitter Type of terrain and degree of obstruction of the link path Sources of interference affecting the receiver Dead spots caused by signal reflections from nearby conductive objects Since the expected transmission range strongly depends on these system conditions range tests should categorically be performed in early project phases The following figures for expected transmission range are considered by using a PTM or STM transmitter device and the RCM radio receiver device with prein
12. c powered radio transmitter device PTM 200C 1 1 Basic Functionality A common electro dynamic energy transducer is actuated by a bow 1 which can be pushed from outside the device by an appropriate push button or switch rocker When the energy bow is pushed down electrical energy is created and an RF telegram is transmitted including a 32 bit device ID Releasing the energy bow generates different telegram data so every PTM telegram contains the information that the bow was pressed or released Long or Short push button operation the time between pushing and releasing the push button can be easily detected by the receiver By doing that applications such as dimming control or blinds control including slat action are simple to implement In addition the PTM telegram transmits the operating status of the contact nipples 2 when pressing the bow This enables the identification of up to 2 appropriate switch rockers or up to 4 pushbuttons EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 4 22 USER MANUAL V1 11 Green Smart Wireless enocearr PTM 200C 1 2 Typical Applications Building installation Industrial automation Consumer electronics Key applications are wall mounted flat rocker switches with 1 or 2 rockers as well as hand
13. defined a new dynamic radio data telegram that is adapted to the individual application It is optimized to the essential features of energy autarkic radio sensors Minimal energy demand Possibility of operating hundred of senders within the same radio cell Maximum transmission reliability Wide transmission range Easy extensibility Suitable for uni and bi directional communication Flexibility for adaptation of different data structures and data quantities Data encryption option 2 3 1 Frequency range The EnOcean PTM 200C operates at 315 0 MHz 2 3 2 Modulation process As modulation process EnOcean uses incoherent amplitude modulation ASK Digital ampli tude modulation enables the implementation of very efficient energy saving transmitters because only the 1 bits are transferred At the same interference signal level the trans mission security of the alternative FSK method is identical to that of the ASK method 2 3 3 Transmission timing The transmission timing of the radio device PTM 200C has been developed to avoid possible collisions with data packages of other EnOcean transmitters as well as disturbances from the environment With each transmission cycle at least three identical subtelegrams are transmitted The transmission of a subtelegram lasts approximately 0 7 ms To optimize data security each telegram is repeated twice within about 20 ms whereas the delay between the second and the third transmission burst i
14. g to VDE 0632 EN 60669 Cover material Hostaform POM Energy bow material PBT 50 GV EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 5 22 USER MANUAL 1 this catwalks are not needed when using one single rocker only a LI LL a SEEN C ee ee ee NENNEN a ALES i AT S E DESI DNI Pe jj Lent Green Smart Wireless enocean Energy Bow Dn N Me p 2 640 2 d LL lL 7 T C C I N 2 dimensions of rocker part Figure 3 PTM 200C without antenna top view note cut A B and C marking EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone 49 89 67 34 689 0 49 89 67 34 689 50 info enocean com www enocean com Subject to modifications PTM 200C User Manual V1 11 October 6 2011 11 10 AM Page 6 22 USER MANUAL Green Smart Wireless enocean e LLM hp ai f f AL Lu Ll B 4 ae i aaa GY QS SAAS SSAA AAMAS LLL L ef igi 1S ik M 4 i d AP AF tt d Pu el AAA Ae TE PRL 14A my 5 7 10 15 Figure 4 PTM 200C without antenna cut A 4 610 2 p EE LLLA E LL ppp P p A SUL LIS E 7 at N M ESSA aS A EERE ASIN CZ7 rZ NN e IEEE N RN ME DL DEO NNI SY pra HA n 1 2 10 1
15. gainst harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio com munications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the re ceiver is connected Consult the dealer or an experienced radio TV technician for help Due to FCC 15 231 operational and timing requirements the PTM 200C switch device must not be operated more than 1088 times per hour pushed or released as one operation each Total duration of transmissions must not exceed more than two seconds per hour PTM 200C packet length is 0 7 ms max 5 redundant packets tolerance of 5 in packet length 50 on average packet Ton Toff ratio This Class B digital apparatus complies with Canadian ICES 003 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041
16. ingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 13 22 USER MANUAL Green Smart Wireless enocean 3 APPLICATIONS INFORMATION 3 1 Laying the antenna For best performance the antenna cable should be layed as shown in the figure below gt 25mm 102mm 63mm 42mm Figure 13 Laying the antenna Important note The distance between antenna foot point and antenna end must be gt 25 mm The antenna area should be maximized The antenna should be placed at the same height above the ground plane as the ro tation axis for the switch rocker see example below EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 14 22 USER MANUAL Green Smart Wireless enocean Figure 13 Example of a well suited antenna 3 2 Construction of application specific Switch Rockers For CAD system development support 3D construction data is available from EnOcean IGS data Using this data the mechanical interface is fixed and the shape and surface of the rocker s can be changed according to requirements Recommendation for suitable rocker material is polycarbonate buckling resistant and wear proof material It is recommended to
17. ns in the Department s Radio List REL Certified equipment shall not be distributed leased sold offered for sale in Canada before the details of this certification have been added to the REL URL http strategis ic qc ca sitt reltel search newRadioSearch do languagezen 2007 07 24 Date Recognized by IC CB ID DE0001 Phone 49 89 67 34 689 0 Fax 49 89 67 34 689 50 info enocean com www enocean com Gerald Schmidt Signature LP y Ze uu Deutscher w iie rungs a dle TTI P G 081 94 DO Subject to modifications PTM 200C User Manual V1 11 October 6 2011 11 10 AM Page 19 22 USER MANUAL Green Smart Wireless enocearn 3 6 Japanese Type Approval PTM 200C complies with the Japanese radio law It carries the following marking on the back side label MIC marking 202YW08108131 T If the certification label cannot be recognized from outside e g installation in a host ap propriate information must be referenced in the user manual CETECOM ICT Services GmbH Untert rkheimer Strasse 6 10 D 66117 Saarbr cken Germany CETECOM Conformity Assessment Body Recognized Certification Body for Japan peal TYPE BASED CERTIFICATE 4 52 f 8 zs die 00 BER Article 2 Clause 1 Item 8 Classification of specified radio equipment Specified low power radio equipment Telemeter Remote Control or data transmission 315MHz band WRONG ARR MD ROP HRED 315 MHz 312 315 25 MHz Type
18. of emissions frequency and 0 2 mW antenna power EALEN Model Name PTM 200C REESE Manufacturer Name EnOcean GmbH E ci Certified Number 202YW08108131 ZELF H B 2009 01 07 Certified Date LiB E45 BRAF 38 RO 24 98 1 BOREL E O C BERE 72 650 Cb S C E ERES This is to certify that the above mentioned certification by type has been granted in accordance with the provisions of Article 38 24 Paragraph 1 of the Radio Law Cetecom ICT Services GmbH Lothar Spitzer M Recognized by The Ministry of Internal Afairs and Communications MIC CAB ID 202 TTI P G 081 94 DO EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 20 22 USER MANUAL V1 11 Green Smart Wireless enocean PTM 200C 4 4 1 EVA 100C is an evaluation kit to support a simple setting up operation of the receiver side when the EnOcean transmitter device PTM 200C is evaluated EVA 100C supports a quick evaluation of RCM 130C receiver operation modes and sup ports the fast development of applications Type DEVELOPMENT TOOLS Evaluation Kit EVA 105C EnOcean Ordering Code Scope of supply EVA 105C Evaluation board EVA PCB 4 2 EnOcean radio devices STM 110C PTM 200C and RCM 130C CD with RS232 PC link monitor software and detailed kit documentation
19. pplications processes and circuits EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship Devices or systems containing RF components must meet the essential requirements of the local legal authorities The modules must not be used in any relation with equipment that supports directly or indi rectly human health or life or with applications that can result in danger for people animals or real value Components of the modules are considered and should be disposed of as hazardous waste Local government regulations are to be observed Packing Please use the recycling operators known to you By agreement we will take pack ing material back if it is sorted You must bear the costs of transport For packing material that is returned to us unsorted or that we are not obliged to accept we shall have to invoice you for any costs incurred EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 82041 Oberhaching info enocean com October 6 2011 11 10 AM Germany www enocean com Page 2 22 USER MANUAL Green Smart Wireless enocean TABLE OF CONTENT 1 GENERAL DESCRIPTION esas n de raf SERE ion UNE PSU A EE E UN d OCURRE DCUM DIN E 4 1 1 BSG EMPDOBOTTSITE Us euivitme sese Pera prPA MEI Dosrd pn ITI Do Fons Ea DPI URN NECI I OIM NE 4 1 2 TVDIESIJA
20. s effected at random If some residual energy is available after transmission of three subtelegrams up to 2 further subtelegrams are sent EnOcean GmbH Kolpingring 18a 82041 Oberhaching Nominal values 5 ms 10 ms 0 7 5 ms at random Figure 11 PTM 200C radio timing Phone 49 89 67 34 689 0 Subject to modifications Fax 49 89 67 34 689 50 PTM 200C User Manual V1 11 info enocean com October 6 2011 11 10 AM www enocean com Page 12 22 Germany USER MANUAL Green Smart Wireless enocean 2 3 4 Reliable radio transmission within systems operating many sensors The very short telegrams of EnOcean transmitters enable the operating of a large number of transmitters within the same radio cell the error rate caused by telegram collisions remains extremely low Statistically viewed the transmission reliability is still greater than 99 99 in the case of 100 radio sensors that transmit once every minute This means that even large office buildings and also huge industrial facilities can be equipped with a large number of sensors of this kind of radio technology 100 M oom Nl A LAU Typical Radio Sensor 99 9 Transmission probability in 96 1 10 100 1000 Number of senders transmitting one time per minute Figure 12 Probability of transmission failure caused by radio data collision for EnOcean light switch transmitter PTM 200C EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolp
21. stalled whip antenna and may be used as a rough guide only Line of sight connections Typically 30 m range in corridors up to 100 m in halls Plasterboard walls dry wood Typically 30 m range through max 5 walls Brick walls aerated concrete Typically 20 m range through max 3 walls Ferroconcrete walls ceilings Typically 10 m range through max 1 ceiling Fire safety walls elevator shafts staircases and supply areas should be considered as screening The angle at which the transmitted signal hits the wall is very important The effective wall thickness and with it the signal attenuation varies according to this angle Signals should be transmitted as directly as possible through the wall Wall niches should be avoided Other factors restricting transmission range Switch mounted on metal surfaces up to 60 loss of transmission range Hollow lightweight walls filled with insulating wool on metal foil False ceilings with panels of metal or carbon fiber Lead glass or glass with metal coating steel furniture The distance between EnOcean receivers and other transmitting devices such as computers audio and video equipment that also emit high frequency signals should be at least 1 m A summarized application note to determine the transmission range within buildings is avail able as download from www enocean com EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 PTM 200C User
22. tification Body at Industry Canada CERTIFICATE OF CONFORMITY Certificate Holder Model Identification Description Equipment Category Standards and Specifications OATS Facility OATS Facility ID IC Certification Number Frequency Range Emission Designator RF Output Rating Antenna Information Cetecom Registration No EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany PTM200C Pushbutton Transmitter Remote Control Device RSS210 Issue 7 Cetecom ICT Services GmbH Untertuerkheimer Str 6 10 66117 Saarbruecken Germany 3463A 1 5713A PTM200C 315 MHz 187KA1D 59 8 dBuV m 3m External whip antenna 2 4706 07 Green Smart Wireless enocearn Certification of equipment means only that the equipment has met the requirements of the above noted specification License applications where applicable to use certified equipment are acted on accordingly by the issuing office and will depend on the existing radio environment service and location of operation This certificate is issued on condition that the holder complies and will continue to comply with the requirements of the radio standards specifications and procedures issued by Industry Canada This certificate is issued on condition that the holder complies and will continue to comply with the requirements of the radio standards specifications and procedures issued by the Department The Bureau will record the details of all certificatio
Download Pdf Manuals
Related Search