Flat Par TW12 User Manual
Contents
1. Standard 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 20 Flat Par TW12 With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 10 fixtures maximum After 10 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures Flat Par TW12 Power Cord Daisy Chain Fuse Replacement Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse Flat Par TW12 Listed below are a few common problems the user may encounter with solutions Trouble Shooting Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not act2. 128 135 1 134 201 off Color2 1 7 255 206 143 Colorl9 136 143 0 145 212 Color3 8 15 254 177 153 Color20 144 151 0 121 192 Color4 16 23 254 192 138 Color21 152 159 0 129 184 Colors 24 31 254 165 98 Color22 160 167 0 83 115 Color6 32 39 254 121 0 Color23 168 175 0 97 166 Color7 40 47 176 17 0 Color24 176 183 1 100 167 Color8 48 55 96 0 11 Color25 184 191 0 40 86 Color9 56 63 234 139 171 Color26 192 199 209 219 182 Colorl0 64 71 254 5 97 Color27 200 207 42 165 85 Colorll 72 79 175 mm 173 Color28 208 215 0 46 35 Colorl2 80 87 19 130 199 Color29 216 223 8 107 222 Colorl3 88 95 147 164 212 Color30 224 231 107 156 231 Colorl4 96 103 88 2 163 Color31 232 239 165 198 247 Colorl5 104 111 0 38 86 Color32 240 247 0 0 189 Colorl6 112 119 0 142 208 Color33 248 255 165 35 1 Colorl7 120 127 52 148 209 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 19 Flat Par TW12 Photometric Chart ww D40 2530 600 216 137 6 88 5 cw D40 3220 o 79 350 o 1 128 ux Amber D40 2020 507 i 218 123 7 5 0 Distance m Flat Par TW12 Dimmer Curve Chart Dimmer 100 Eai a 50 I 10 i 0 en i Tie Da es Ramp Effect Pa ead OS Fade Time 0 a 1S Fade Time Trise ms Teow ms Tise ms Tont
3. 2 Year 730 days Color Temperature Variable 2700 6500 Cool White gt 6500 K Warm White gt 2700 K Amber Wavelength 590 595NM CRI Values Cool White 70 80 Warm White 70 80 Amber None Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Flat Par TW12 User Manual Page 26 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj com Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On FTE facebook com americandj twitter com americandj youtube com adjlighting
4. Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 21 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers
5. LLC provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or sugges tions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 323 582 3322 Fax 323 582 3108 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com Flat Par TW12 User Manual Page 2 Flat Par TW12 e Mulit Colors Five Operating Modes e Electronic Dimming 0 100 Built in Microphone e DMX 512 protocol 3 Pin DMX Connection 6 DMX Modes 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 8 Channel Mode and 9 Channel Mode e ADJ LED RC compatiable Not Included Power Cord Daisy Chain See page 21 Features Flat Par TW12 Warranty Registration The Flat Par TW12 carries a 2 year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must
6. be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our customer support number All pack ages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper Flat Par TW12 The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp Installation ADJ Products LLC www adj com Flat Par TW12 User Manual Page 3 Flat Par TW12 Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture
7. connector only Connect the first Slave unit to the Master Set the Master unit to your desired mode of operation For the Slave unit s press the MODE button until SLAv is displayed The Slave unit s will now follow the Master ADJ Products LLC www adj com Flat Par TW12 User Manual Page 11 on Flat Par TW12 ADJ LED RC3 Operation The ADJ LED RC3 infrared remote sold seperately has many dif fernet functions and gives you complete control of your Flat Par TW12 To control the your desired fixture you must aim the controller at the front of the fixture and be no more the 30 feet away To use the ADJ LED RC3 you must first activate the fixtures infrared receiver to activate the receiver please see the instructions on page 10 BLACKOUT Pressing this button will blackout the fixture AUTO RUN Pressing this button will cycle through the auto run mode color fade mode and color change You can control the speed of the 3 modes by pressing the SPEED button first and then pressing the and buttons In color fade and color change mode press cc the and buttons to scroll through the 8 modes PROGRAM SELECTION Pressing this button activates static color mode Use the or to scroll through the 32 colors Press Flash to activate deactivate strobing Use the and buttons to adjust the strobe speed DMX MODE Press this butto
8. 7 14 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power wh
9. Mode press the MODE button until Ch02 is displayed This is the 2 Channel DMX Mode To run the 3 Channel Mode press the MODE button until Ch03 is displayed This is the 3 Channel DMX Mode To run the 4 Channel Mode press the MODE button until Ch04 is displayed This is the 4 Channel DMX Mode To run the 5 Channel Mode press the MODE button until Ch05 is displayed This is the 5 Channel DMX Mode To run the 8 Channel Mode press the MODE button until Ch08 is displayed This is the 8 Channel DMX Mode To run the 9 Channel Mode press the MODE button until Ch09 is displayed This is the 9 Channel DMX Mode 4 See pages 14 19 for the DMX values and traits of each channel mode 5 After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX controller WW CW A Dimmer Mode 1 Plug the fixture in and press the MODE button until 2 When H XXX is displayed you are in Warm White dimming mode Press the UP and DOWN buttons to adjust intensity 3 When C XXX is displayed you are in Cool White dimming mode Press the UP and DOWN buttons to adjust intensity 4 When A XXX is displayed you are in Amber dimming mode Press the UP and DOWN buttons to adjust intensity 5 After you have adjusted the colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the strobe mode 6 S XXX will b
10. Speed button and use the and buttons to adjust the sound sensitivity level SLAVE This designates the fixture as a slave fixture in a master slave configuration SET ADDRESS Press this button to set the DMX address Press this button first then press the numbers to set the address Note When setting the DMX address each time a number is pressed a LED color will glow when you have set the DMX address correctly all LED s will flash 2 3 times Example Set DMX Address 1 Press S 0 0 1 Set DMX Address 245 Press S 2 4 5 WW CW A Press either one of these buttons and the press the or to adjust the output intensity Press Flash to activate deactivate strobing Use the and buttons to adjust the strobe speed ADJ Products LLC www adj com Flat Par TW12 User Manual Page 13 Flat Par TW12 2 Channel Mode Flat Par TW12 5 Channel Mode Le a eee era 0 255 COLOR MACROS WARM WHITE See the Color Macro chart on page 19 0 100 0 255 DIMMER 0 100 COOL WHITE 0 100 AMBER Fossa WARM WHITE 0 255 0 100 0 100 MASTER DIMMER 0 100 STROBING LED OFF LED ON las Ei 0 255 0 100 255 0 100 2 LED ON em O amion To RANDOM STROBING SLOW FAST WARM WHITE 0 255 0 100 A DON oes 0 100 0 255 0 100 STROBING SLOW FAST 0 255 0 100 sa MASTER DIMMER 0 255 0 100 ADJ Products LLC www a
11. T UP button until SP XX is displayed When this is displayed you can adjust the running speed of your desired program Use the UP or DOWN button to adjust the speed between SP 01 Slowest and SP 16 fastest Once you have set your desired running speed press the SET UP button to return to your desired Auto Run Mode Static Color Mode J 2 Plug the fixture in and press the MODE button until CLXX is dis played There are 32 colors to choose from Select your desired color by pressing the UP and DOWN buttons After you have selected your desired color you can activate strobing by pressing the SET UP but ton to enter the strobe mode S XXX will be displayed this is strobing The strobing can be adjusted between S 000 strobe off to S 015 fastest strobe ADJ Products LLC www adj com Flat Par TW12 User Manual Page 9 Flat Par TW12 Operating Instructions Default Running Mode This is a default running mode When this mode is activated all modes will return to their default settings 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until dEFA is displayed 3 Press the UP and DOWN buttons simultaneously Press the MODE button to exit ADJ LED RC3 This function is used to activate and deactivate the ADJ LED RC3 Remote Control When this function is activated yo
12. TE 0 100 AMBER 0 100 MASTER DIMMER 0 100 STROBING LED OFF LED ON STROBING SLOW FAST LED ON PULSE STROBING SLOW FAST LED ON RANDOM STROBING SLOW FAST LED ON COLOR MACROS See the Color Macro chart on page 19 PROGRAMS NO PROGRAM COLOR FADE 1 COLOR FADE 2 COLOR FADE 3 COLOR FADE 4 COLOR FADE 5 COLOR FADE 6 COLOR FADE 7 COLOR FADE 8 COLOR CHANGE 1 COLOR CHANGE 2 COLOR CHANGE 3 216 223 COLOR CHANGE 4 224 231 COLOR CHANGE 5 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 18 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 Flat Par TW12 9 Channel Mode PROGRAMS COLOR CHANGE 6 SOUND ACTIVE MODE 1 SOUND ACTIVE MODE 2 PROGRAM SPEED SOUND SENSITIVE PROGRAM SPEED SLOW FAST 232 239 240 247 248 255 SOUND SENSITIVITY MIN MAX DIMMER CURVES STANDARD STAGE TV ARCHITECTURAL THEATRE DEFAULT TO UNIT CURVE SETTING Channels 1 2 and 3 will not work when Channel 6 is being used When using Channel 7 values 128 239 Channel 8 will control the speed of the programs When using Channel 7 values 240 255 Channel 8 will control the sound sensitivity Flat Par TW12 Color Macro Chart Color DMX WW CW A COLOR INTENSITY Color DMX WW CW A COLOR INTENSITY No VAULE Ww cw A No VAULE WW CW A Colorl 0 0 0 0 Colorl8
13. This warranty was revised after December 1 2012 MANUFACTURER S LIMITED WARRANTY PERIODS Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LEDs and lamps Laser Products 90 Day Limited Warranty L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Flat Par TW12 User Manual Page 22 Flat Par TW12 Notes ADJ Products LLC www adj com Flat Par TW12 User Manual Page 23 Flat Par TW12 Notes Flat Par TW12 Notes ADJ Products LLC www adj com Flat Par TW12 User Manual Page 24 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 25 Flat Par TW12 Specifications Model Flat Par TW12 Voltage 100V 240V 50 60Hz LEDs 12 x 5W 3 in 1 Tri LED s Beam Angle 40 Degrees Working Position Any safe working position Power Draw 61W Power Cord Daisy Chain 10 Fixtures Max Fuse 2A Weight 7lbs 3 25Kgs Dimensions 13 L x 11 W x 4 H 328 x 280 x 105mm Colors Warm White Cool White amp Amber DMX Channels 6 DMX Modes 2 Channel Mode 3 Channel Mode 4 Channel Mode 5 Channel Mode 8 Channel Mode amp 9 Channel Mode Warranty
14. dj com Flat Par TW12 User Manual Page 14 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 15 Flat Par TW12 8 Channel Mode WARM WHITE 0 100 COOL WHITE 0 100 AMBER 0 100 MASTER DIMMER 0 100 STROBING LED OFF LED ON STROBING SLOW FAST LED ON PULSE STROBING SLOW FAST LED ON RANDOM STROBING SLOW FAST LED ON COLOR MACROS See the Color Macro chart on page 19 PROGRAMS NO PROGRAM COLOR FADE 1 COLOR FADE 2 COLOR FADE 3 COLOR FADE 4 COLOR FADE 5 COLOR FADE 6 COLOR FADE 7 COLOR FADE 8 COLOR CHANGE 1 COLOR CHANGE 2 COLOR CHANGE 3 216 223 COLOR CHANGE 4 224 231 COLOR CHANGE 5 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 16 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 Flat Par TW12 8 Channel Mode PROGRAMS COLOR CHANGE 6 SOUND ACTIVE MODE 1 SOUND ACTIVE MODE 2 232 239 240 247 248 255 PROGRAM SPEED SOUND SENSITIVE 0 255 PROGRAM SPEED SLOW FAST 0 255 SOUND SENSITIVITY MIN MAX When channel 6 is being used channels 1 3 will cannot be used When channel 7 is between the values of 128 239 channel 8 will control the program speed When channel 7 is between the values of 240 255 channel 8 will control the sound sensitivity ADJ Products LLC www adj com Flat Par TW12 User Manual Page 17 Flat Par TW12 9 Channel Mode WARM WHITE 0 100 COOL WHI
15. e displayed this is strobing mode The strobing can be adjusted between S 000 strobe off to S 015 fastest strobe ADJ Products LLC www adj com Flat Par TW12 User Manual Page 8 Flat Par TW12 Operating Instructions Sound Active Mode In this mode the Flat Par TW12 will react to sound and chase through the different colors 1 Plug the fixture in and press the MODE button until So X is dis played X represents the sound active mode 1 8 currently dis played The fixture will now change via sound To adjust the sound sensivity press the SET UP button SJ X will be displayed Use the UP or DOWN buttons to adjust the sensitivity SJ 1 is the least sensitive SJ 8 is the most sensitive Auto Run Mode There are 3 types of Auto Run Modes to choose from Color Fade Color Change and both modes running together The running speed is adjustable in all 3 modes 1 Plug the fixture in and press the MODE button until either AF X AJ X or A JF is displayed AF X Color Fade mode there are 8 Color Fade modes to choose from Use the UP or DOWN buttons to scroll through the different Auto Fade modes AJ X Color Change mode there are 8 Color Change modes to choose from Use the UP or DOWN buttons to scroll through the different Auto Change modes A JF Both Color Fade and Color Change modes running After you have chosen your desired running mode press the SE
16. e readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Data Compliment signal Pin 2 Data True signal Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com Flat Par TW12 User Manual Page 6 Flat Par TW12 Operating Instructions The display will lock after 30 seconds press the MENU button for 3 seconds to unlock LED Display On Off To set the LED display to turn off after 10 seconds press the MODE but ton until don is displayed press the UP button to display doff Now the display will disappear after 10s Press any button to turn the display on again Be advised though that the display will turn off automatically after 10 seconds To set the display press the MODE button until dXX is displayed XX represents either on or oFF Use the UP or DOWN buttons to select either don LED display on at all times doFF LED display shuts off after 10 seconds LED Display Inversion Follow these instructions to flip the display 180 so that the display can be read upside down 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or oFF 2 Press the SET UP button until Stnd is displayed 3 Press the UP or DOWN butt
17. en not in use Thank you Flat Par TW12 Introduction Unpacking Thank you for purchasing the Flat Par TW12 by ADJ Prod ucts LLC Every Flat Par TW12 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the ship ping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are miss ing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contact ing customer support Introduction The ADJ Flat Par TW12 is part of a continuing pursuit to create high quality intelligent lighting The Flat Par TW12 is a DMX intel ligent high powered LED par fixture This fixture can be used in a stand alone mode or connected in a Master Slave configuration This wash has five operating modes Sound Active mode Auto Run mode WW CW A Dimmer mode Static Color mode and DMX control mode To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Customer Support ADJ Products
18. ivate the unit 2 Make sure that Sound Active mode is activated Flat Par TW12 Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing Clean the external optics with glass cleaner and a soft cloth every 20 days Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew ADJ Products LLC www adj com Flat Par TW12 User Manual Page 21 Cleaning Ra o Flat Par TW12 Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ P
19. n to cycle between DMX Channel mode selection DMX addressing DMX State and dimming curve selection Each press of this button will change to the next mode In DMX State mode press the the and buttons to scroll through the DMX state modes See DMX State on page 10 11 for more info ced In DMX address mode press the the and buttons to adjust the DMX address In dimmer curve setting press the the and buttons to scroll through the dimmer curves See Dimmer Curves on page 11 for more info In DMX Channel selection press the the and buttons to scroll through the different DMX Channel modes See DMX mode on pages 7 8 for more info The info below and on the next page will help iden tify which channel mode you are in If the Warm White LED s glow you are in 2 Channel Mode If the Cool White LED s glow you are in 3 Channel Mode If the Amber LED s glow you are in 4 Channel Mode e If the Warm amp Cool White LED s glow you are in 5 Channel ADJ Products LLC www adj com Flat Par TW12 User Manual Page 12 Flat Par TW12 ADJ LED RC3 Operation Mode If the Warm White amp Amber LED s glow you are in 8 Channel Mode If Cool White amp Amber LED s glow you are in 9 Channel Mode SOUND ACTIVE This button activates sound active mode Use the and buttons to scroll through the 8 sound active modes Press the
20. nty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect ADJ Products LLC reserves the right to make changes in design and or improvements upon it s products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published
21. ons to reverse the display 180 Operating Modes The Flat Par TW12 has five operating modes Sound Active mode The unit will react to sound chasing through the built in programs Static Color Mode There are 32 colors to choose from Auto Run Mode There are 3 Auto Modes to choose from WW CW A Dimmer Mode Choose one of the three colors to remain static or adjust the intensity of each color to make your desired color DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs The Flat Par TW12 has 6 DMX modes 2 Channel mode 3 Channel mode 4 Channel mode 5 Channel mode 8 Channel mode and a 9 Channel mode ADJ Products LLC www adj com Flat Par TW12 User Manual Page 7 Flat Par TW12 Operating Instructions 1 2 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller To run your fixture in DMX mode press the MODE button until d XXX is displayed XXX represents the current displayed ad dress Use the UP or DOWN buttons to select your desired DMX address then press the SETUP button to select your DMX Channel mode Use the UP or DOWN buttons to scroll through the DMX Channel modes The Channel modes are listed below To run the 2 Channel
22. roducts LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warra
23. round lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 O 2 ey Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference It is always advisable Ss o to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 Figure 2 XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative lal i ins evita Pin 3 Data True positive 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors ar
24. shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Flat Par TW12 can be controlled via DMX 512 protocol The Flat Par TW12 has 6 DMX channel modes please see pages 7 8 for the different modes The DMX address is set on the back panel of the Flat Par TW12 Your unit and your DMX controller require a standard 3 pin XLR connec tor for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com Flat Par TW12 User Manual Page 5 Flat Par TW12 Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the g
25. that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Flat Par TW12 User Manual Page 4 Flat Par TW12 Set Up Power Supply The ADJ Flat Par TW12 contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the cor rect power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the
26. u can control the fixture using the ADJ LED RC3 Please see the next page for ADJ LED RC3 controls and functions 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until IrXX is displayed XX represents either on or oF 3 Press the UP or DOWN buttons to either activate the remote func tion On or deactivate it Off DMX State This mode can be used as a precaution mode that in case the DMX signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operating mode you would like the unit to return to when power is applied 1 Press the MODE button until the DMX address is displayed 2 Press the SET UP button until No X is displayed X represents a number between 0 2 3 Use the UP or DOWN buttons to operating mode you would like the unit to start up in when power is applied or the DMX signal is lost e NO 0 BLACKOUT If the DMX signal is lost or power is applied the unit will automatically go into stand by mode e NO 1 HOLD If the DMX signal is lost the fixture will stay in the ADJ Products LLC www adj com Flat Par TW12 User Manual Page 10 Flat Par TW12 Operating Instructions last DMX set up If power is applied and this mode is set the unit will automaticall
27. y go into the last DMX set up e NO 2 FADE PROGRAM If the DMX signal is lost or power is applied the unit will automatically run the fade program Dimmer Curve This is used to set the dimmer curve used with DMX mode See the Dimmer Curve chart on page 18 for more information 1 Plug the fixture in and press the MODE button until the DMX address is displayed 2 Press the ENTER button until dr X is displayed X represents the current dimming mode 3 Use the UP and DOWN buttons to find your desired dimmer curve Press SET UP when you are finished dr 0 Standard dr 1 Stage e dr 2 TV dr 3 Architectural dr 4 Theater Flat Par TW12 Master Slave Configuration Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units built in programs Any unit can act as a Master or as a Slave however only one unit can be pro grammed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that the Male XLR connector is the input and the Female XLR con nector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR
Download Pdf Manuals
Related Search