x-torm 300 - Astrolite Web
Contents
1. 96 111 Gobo 6 112 127 Gobo 7 128 255 Gobo wheel rotation from slow to fast Channel 4 Colour wheel 0 15 Open white 16 31 pink 32 47 yellow 48 63 orange 64 79 green 80 95 red 96 111 blue 112 127 purple 128 255 rainbow effects in both directions Channel 5 Rotating gobo index rotating gobo rotation O 127 forward gobo rotation from slow to fast 128 252 backward gobo rotation from slow to fast 253 255 gobo to be static Channel 6 shutter and strobe 0 50 shutter open 51 220 strobe from slow to fast 221 255 shutter open Channel 7 four facet prism 0 255 static prism Channel 8 prism rotation 0 159 clockwise prism rotation 160 255 counter clockwise prism rotation Channel 9 focusing Channel 10 reset Channel 11 prism rotation 0 159 clockwise prism rotation 160 255 counter clockwise prism rotation Channel 12 focusing Channel 13 gobo indexing Channel 14 reset Lighting the Future www astroliteweb com Control Board 7 LED Display O Q UP DOWN MENU ENTER The Control Board offers several features you can simply set the starting address reset The main menu is accessed by pressing the MENU and browse through the menu by pressing the Up button Press the Enter button in order to select the desired menu You can change the selection by pressing the Up button Confirm every selection by pressing the Enter button You can leave every mode by pressing the mode The functions provided2. are described in the following sections 1 Press MENU till A001 displays and then set the desired address and confirm by pressing the button ENTER 2 Pan Reverse With this function you can reverse the Pan movement Select PAN by pressing UP button Press ENTER the display shows PAN and it means the pan moves in the direction set ex factory and PAN means the pan moves in the opposite direction 3 Tilt Reverse With this function you can reverse the tilt movement Select TLT by pressing UP button Press ENTER the display shows TLT and it means the pan moves in the direction set ex factory and TLT means the pan moves in the opposite direction 4 Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel Select CH by pressing UP Press ENTER and the display shows CH1 CH10 and select any one of the 10 items and confirm by pressing the button ENTER and then the different effects on the DMX value will be achieved by pressing UP or DOWN buttons 5 Reset With this function you can Reset the device via the Control Board Select REST by pressing UP button Press ENTER the device will reset Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse of same type and rating Liehting the Future www astroliteweb com Before replacing the fuse unplug mains
3. X TORM 300 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP Introduction Thank you for having chosen a new moving head 250 You acquired a versatile powerful and intelligent lighting effect Unpack your unit and make sure that there are no damages caused by transportation Should there be any please consult your local dealer and do not take the device into operation Features Colour system Colour wheel with 7 different dichroic colour filtres and white Rainbow effect in both directions Gobo wheel with 7 interchangeable rotating gobos and open The rotating gobos can be turned by 360 the adjusted position is memorized High speed rotating 4 facet prism shutter dimmer unit allowing very smooth dimming and strobo effect 1 10 flash per sec e LED display Readout fixture receiving DMX values Remote reset function Silent fans cooling 10 DMX channels Pan movement range 530 Tilt movement range 280 High luminous efficiency parabolic mirror and double condenser system Motorized focus controllable via DMX All lenses are anti reflection coated For PHILIPS MSD 250 2 lamps DMX control via every standard DMX controller Operating determinations This device is a moving head spot for creating decorative effects This product is only allowed to be operated with an alternatin
4. g current of 220 V 60 Hz and was designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Never run the device without lamp Do not shake the device Avoid brute force when installing or operating the device The minimum distance between light output and the illuminated surface must be more than 1 meter Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature fa must never be exceeded Lighting the Future www astroliteweb com 1 Projector head jLens 3 Yoke 4 Base 5 Carrying handle 6 Ventilation slot aa 10 Power Switch 11 Power supply 8 DMX 9 DMX output input Fitting Exchanging the lamp Install the lamp with the device switched off only Unplug from mains before Lighting the Future www astroliteweb com Adjust lamp position by turning lamp adjusting screws WARNING Always dlaconmect from malns before replac
5. ing thelornp Prolonged exposure to unshielded lampcan couse eye Ekin burma 2 Lampadjusting Screw 1 Re lamping screw Lamp is hot Risk of fire Wait at least 15min before opening the covers and removing lamp from the fixture Disconnect the fixture from AC power before re lamping Protect hands and eyes Maximum room temperature t 40 C Minimum distance from flammable material d 0 5m The lamp holder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp open the shutter and the iris set the dimmer intensity onto 100 and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws clockwise turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws counterclockwise turn at a time the light is bright and evenly distributed Remove the re lamping screws for re lamping To insert the lamp PHILIPS MSD 250 2 open the small cover at the head s rear panel by loosening the 2 screws on the cover Gently pull out the
6. lamp assembly If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Do not touch the glass bulb bare handed during the installation Make sure that the lamp is installed tightly into the lamp holder system Reinsert the lamp assembly and tighten the screws again Never on off power the lamp at continuous step and when the lamp off wait at least 5 minutes till the lamp cools enough and on power the lamp Lighting the Future www astroliteweb com DANGER OF FIRE When installing the device make sure there is no highly inflammable materials within a distance of min 0 5 m CAUTION Use 2 appropriate clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Use 2 appropriate clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure Clamps must be locked with both 1 4 turns and the 1 4 turns lock in position when turned fully clockwise Always use two clamps to mount the fixture Always secure safety wire before suspending the fixture Use the m10 screws to fix the clamps on the fixing holders on the bottom of the device and then screw the hanging screw into the bottom base and pu
7. lead Procedure Step 1 Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing and fix it Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by a special power supply cable available at your dealer Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS Power supply 220 V AC 60 Hz Power consumption 500W DMX 512 connection 3 pin XLR Flash rate 10 Hz Dimension 420x410x490mm Weight net 22 0 kg Maximum ambient temperature ta 45 C Please note Any information is subject to change without prior notice Lighting the Future www astroliteweb com
8. t on safety wire 12 Clamp Fixing Plate 13 Safety Wire Hanging STEW DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture Function of the control channels Channel 1 Horizontal movement Pan Push slider up in order to move head horizontally PAN Gradual head adjustment from one end of the slider to the other The head can be turned by 530 and stopped at any position you wish Channel 2 Vertical movement Tilt Lighting the Future www astroliteweb com Push slider up in order to move head vertically TILT Gradual head adjustment from one end of the slider to the other The head can be turned by 280 and stopped at any position you wish Channel 3 rotating gobo wheel 0 15 Open hole 16 31 Gobo 1 32 47 Gobo 2 48 63 Gobo 3 64 79 Gobo 4 80 95 Gobo 5
Download Pdf Manuals
Related Search