PROGRAMMABLE RELAY I/O CARD USER MANUAL
Contents
1. PROGRAMMABLE RELAY I O CARD USER MANUAL INTERNAL CIRCUIT Common R1 Selected Event Relay1 Summary Alarm Relay2 Power Fail Relay3 Battery Low Relay4 On Bypass Relay5 Overload Relay6 Over Temperature R4 Back To Previous Menu R R5 Please Enter Your Choice gt R2 R3 fly R6 Once the configuration is complete SW2 OoOo o MUST be switched to the ON position to appl the new settings switch SW2 back to the OFF position to reset to the default settings D Press 2 to configure the Input signal FEATURES a Configure Input Signal ari cE ea This relay I O card is an UPS management OUTLINE iket ae Spanier Task Shenae product with 6 relay output contacts for monitoring 2 Input Signal Confirm 3 Seconds the status and 1 input contact as a shutdown UPS OOO 3 Delay Before Shutdown 30 Seconds or a battery test command 0 Back To Previous Menu Features Monitor UPS events 6 programmable relay output contacts O Configurable normal open or normal close for each relay contact Configurable UPS shutdown delay time Configurable input signal as shutdown UPS or battery test Has the ability to protect up to 6 computers unattended shutdown gracefully CPU Pin Please Enter Your Choice gt In th2. is menu the input signal can be redefined as shutdown UPS or battery test signal Meanwhile the UPS shutdown delay time is also adjustable to a maximum of 9999 seconds Press 3 to configure the normal open or normal close for each relay qe rer Customize Output Relay SSSSSSSSssss z VO PINOUT GND R Ground for relays Common 12 24VDC Default Alarm Event R1 Summary Alarm TECHNICAL SPECIFICATION R2 Power Fall TECHNICAL SPECIFICATION Battery Low R4 On Bypass Size 130 x 60 mm R5 Overload Weight 200 g Operating Temperature 0 40 C E ut A battery test Operating Humidity 10 80 put Power Input 8 20V DG LL Transmit to PC connect to sub9 pin2 Power Consumption 1 2 Watts Rx Receive from PC connect to sub9 pin3 f GND C Ground for configuration Tx and Rx pins OFF Default ON Selected Event Normal Close Normal Open Normal Close Normal Open Relay5 Normal Close Relay6 Normal Open Back To Previous Menu Relay Relay1 Relay2 Relay3 Relay4 Please Enter Your Choice gt Once the configuration is complete SW2 MUST be switched to the ON position to appl the new settings Switch SW2 back to the OUTPUT CONTACT RATING Maximum DC Voltage DC Current Relay swi Normal open for default settings Normal close for default setti
3. ngs sw2 Default settings Customized settings OFF position to reset to the default settings Press 0 to quit this configuration session The system would prompt you to save or not R1 R6 24V 1A Press Y to save your settings N to ignore POWER OPTION IN WIN 2000 XP This relay card has the ability to provide UPS signals for Windows NT4 2000 XP 2003 First connect the RS232 port on the PC to the relay card as shown Then open the power option from control panel and click on the UPS tab to setup the signals polarity select Positive for Power Fail Low Battery and UPS Shutdown Since the R1 R6 contacts are programmable the output contacts can be Firmware Version Relay Card V1 4 R4 configured for 3 1 Customize Output Relay computers with 2 2 Configure Input Signal na signals power fail Lo Oanei Normal Open or Normal Close i and low battery on Shutdown UPS ee 6 computers with one signal power fail or low battery PROGRAMMABLE CONTACTS COMMUNICATION SETUP Maximum 1 Connect Tx to pin2 Rx to pin3 and GND C to DC Voltage DC Current pins of PC RS232 port 24 V 10 mA 2 Inthe Windows environment launch the Hyper Terminal program then open the specified COM port Set the following properties Baud rate 2400 Data Bits 8 Parity None Stop Bit 1 Flow Control None UT RATING Input APPLICATION EXAMPLE In this case we ll use the defa
4. ult settings please set SW1 and SW2 to the OFF position Apply 12VDC to Common contact and connect the lamps to R1 R6 terminals Install a push button from the Common contact to the input terminal Press the button for at least 3 seconds to shutdown the UPS remotely Common 12V Common RTS pin7 CONFIGURATION 1 Press lt Enter gt to get the main menu of the sy programmable relay card Power Fail R2 gt Battery Low R3 gt GND R GND pin5 CTS pin8 ee DCD pint lt lt Summary Alarm lt Power Fail lt Battery Low Please Enter Your Choice gt Press 1 to configure the alarm event for R1 R6 Contacts R1 R6 can be configured for different power events lt On Bypass DTR pin4 Overload lt Over Temperature Note All of the computers must have the same earth ground potential Connect all of the computers input power to the same UPS lt lt Shutdown UPS
Download Pdf Manuals
Related Search