User Manual For Portable Biometric Compact Lock Box
Contents
1. BARSKA User Manual For Portable Biometric Compact Lock Box DELETING ALL FINGERPRINTS continued 9 All fingerprints stored in the lock box have been deleted 10 The lock box is in demo mode ANY fingerprint can open the lock box INSTALLING THE CABLE Included with the lock box is a steel cable that may be attached to any stationary item for increased security The cable hole is located on the side of the lock box Installing the Cable 1 Thread one end of the cable Open lock box by using the Locate the stationary item you would like the safe to be attached to and wrap the cable around the FL stationary item a through the other loop of the cable The loop that was just created in this step should be wrapped around the stationary item personal pin code or access key Locate the cable slot Place the unused loop of the steel cable with the with the metal stopper portion in the lock box through the cable slot Close lock box and ensure that the lock box is locked Slightly tug on the cable to ensure that the cable is securely attached to the lock box Removing the Cable 1 Open lock box by using a registered fingerprint or access key 2 Lift steel cable out of the cable slot 3 Pull the one end of the cable through the other loop of the cable 4 Store cable in a safe place MOUNTING The lock box may be mounted to a wall or to the floor The three pre drille2. SBARSKA User Manual For Portable Biometric Compact Lock Box PARTS OF THE LOCK BOX Parts of the Safe A Key Entry B Indicator Light O 0 O C Fingerprint Scanner D Wake Up Button E Initialization Button F Battery Compartment and Cover G Cable Slot H Mounting Holes located under the safe WARNING Avoid leaving lock box open and unattended it will allow unauthorized individuals to add their fingerprint and or reprogram the lock box gaining full access to the lock box and the contents OPENING THE LOCK BOX WITH ACCESS KEY 1 Insert access key into key entry turn clockwise to open partially lift lid of lock box and remove access key by turning it counter clockwise 2 Open lock box by lifting the lid of the lock box NOTE Store access keys in a secure place NOT inside of lock box When calling for replacement or additional access keys have the access key code number ready The access key code is etched in the key entry and on the access keys BATTERIES 1 Locate the battery compartment and remove battery cover 2 Gently slide battery holder out of the compartment 3 Place 4 AA batteries and pay attention to the polarity of each battery 4 Gently slide battery holder back into place 5 Replace battery cover REPLACING BATTERIES The red indicator light will start flashing and a continuous beeping sound will be heard This indicates that the batteries are low 1 Open lock box by using the a
3. 1767 Please include all of the following when returning BARSKA products for service and or replacement 1 Please write your complete details Name Address Telephone E mail address RMA etc 2 Purchase receipt or Proof of Purchase Original Copy 3 A brief explanation of the defect 4 A Check Money Order of 20 00 to cover inspection shipping and handling Please allow 6 8 weeks for delivery BARSKA will examine and test returned product and repair or replace defective part s or units with new part s or a new unit if necessary within the warranty period Purchaser is required to remit 20 00 to BARSKA for return shipping and handling at time product is returned If repair is required after warranty period expiration purchaser will be charged for replacement parts and return shipping BARSKA Optics shall not be liable for any consequential incidental and or contingent damages whatsoever We will not pay shipping insurance or transportation charges from you to us or any import fees duties and or taxes This warranty supersedes all previous BARSKA Optics warranties BC300 9 14 2014 BARSKA 855 Towne Center Drive Pomona CA 91767 t 888 666 6769 f 909 445 8169 www barska com Replacement Keys When calling for replacement or additional access keys have the access key code number ready The access key code is etched in the key entry AND on the access keys
4. ccess key turn clockwise 2 Repeat steps 1 5 of Batteries and replace old batteries with new batteries 3 Close lock box and ensure that the lock box is locked NOTE After replacing the batteries lock box retains registered fingerprints REGISTERING A FINGERPRINT The lock box is in demo mode ANY fingerprint can open the lock box 1 With the lock box open press and release the initialization button 2 A beep will be heard and scanner will flash red 3 Immediately place desired finger on the scanner Hold finger still until registration process is complete 4 Registration process is complete when a total three beeps are heard See below Successful Save Indicator light will flash green followed by one beep indicator light will flash green twice and two consecutive beeps Registration has been successful Unsuccessful Save Indicator light will flash green followed by one beep indicator light will flash red and two consecutive beeps Repeat registration process again NOTE To add more fingerprints users repeat steps above Stores up to 120 fingerprints For security purposes wipe fingerprint off scanner For Accurate and Consistent Fingerprint Scanning Use scanner in low light conditions Use the index finger Place and hold finger firmly on the scanner Each user should register 2 3 different fingerprints TESTING A REGISTERING A FINGERPRINT 1 With lock box lid open press the wake up but
5. ct For all repairs and maintenance contact authorized service centers or distributor BARSKA Customer Service DO NOT place emergency keys inside of lock box 4 BARSKA 1 YEAR LIMITED WARRANTY COMPACT LOCK BOX BARSKA warrants this new lock box to be free of original defects in material and or workmanship under normal use for a period of twelve 12 months from the date product is received by purchaser This warranty does not include damage caused by improper installation or maintenance Damage from misuse abuse accident such as dropping normal wear and tear fire flood or acts of nature Damage from service or repairs other than those performed by BARSKA Labor cost and shipping charges for the removal and replacement of defective parts beyond the initial twelve month warranty period All transportation and shipping charges Removing or altering the seal under any circumstances will automatically void the warranty This warranty is limited to original purchaser and is not transferable This warranty applies only to products purchased in the United States Please email info barska com or call 1 888 666 6769 for Return Merchandise Number RMA before any returns The RMA number must appear on the outside of the shipping package Product must be packed carefully and sturdily in its original packaging to prevent damage in transit and returned freight pre paid to BARSKA OPTICS Repair Department 855 Towne Center Drive Pomona CA 9
6. d mounting holes are located under the lock box and can be exposed by gently removing the rubber pads out of it s place NOTE On Wall Mounting When mounting to a wall be aware of the load bearing to ensure Safety of lock box and contents Failure to do so could result in the lock box falling and damaging property and or people DO NOT mount lock box without anchoring to the wall behind the lock box When mounting to a wall check the wall or cabinet for structural soundness 1 Check location for concealed items such as wires pipes etc 2 Get the appropriate anchors for the type of floor or wall you will be mounting the lock box to wood tile concrete etc 3 Mark the surface to drill holes for the anchors you will be using 4 Drill the appropriate size hole for the anchors you will be using 5 Once mounted test the strength to make sure the lock box is securely mounted CARE AND MAINTENANCE For security purposes wipe fingerprint off scanner when opening and or closing the lock box If necessary use a damp cloth to clean the lock box DO NOT use chemicals or cleaning agents Keep liquids away from the control panel Spills on the control panel will cause damage and possibly electric shock Secure lock box in a proper area to prevent it from falling and causing damage or injury DO NOT over stuff the contents of the lock box it can damage the motor mechanism or the contents DO NOT disassemble the produ
7. ton 2 Place registered finger on the scanner Successfully Saved Fingerprint Indicator light will flash green indicating a valid fingerprint You will hear the lock box unlock Unsuccessful Fingerprint Indicator light will flash red and green consecutively indicating that the fingerprint in not valid Repeat steps in Registering A Fingerprint 4 Close lock box and ensure that the lock box is locked 5 For security purposes wipe fingerprint off scanner OPENING THE LOCK BOX USING A FINGERPRINT 1 Press the wake up button 2 Place registered finger on the scanner 3 The indicator light will flash green indicating a valid fingerprint 4 Gently lift the door of the lock box 5 Close lock box and ensure that the safe is locked 6 For security purposes wipe fingerprint off scanner DELETING ALL FINGERPRINTS 1 With the lock box open locate the battery compartment and remove battery cover 2 Gently slide battery holder of out of the compartment 3 Remove all 4 AA batteries from battery holder 4 Press wake up button a few times to release remaining electronic power 5 Re insert 3 AA batteries and pay attention to the polarity of each battery 6 Press and hold down the initialization button 7 Re insert the last AA battery you will hear 2 beeps release initialization button 8 Gently slide battery holder back into place and replace battery cover 9 14 See reverse side for more information BC346
Download Pdf Manuals
Related Search