Home

VISO 1 Owners Manual

1. S PDIF input is immediately disconnected when a Bluetooth device gets paired or connected with VISO 1 The Bluetooth device takes priority and becomes the active source device Check the corresponding Bluetooth device s manual on how to pair it with VISO 1 VISO 1 SOURCE SELECTION FLOWCHART COMPONENT VIDEO OUTPUT Using compatible iPod models one can playback a stored video in one s iPod and view the video via VISO 1 by making use of the following methods Y Pb Pr e If your particular iPod model supports component video signal connect VISO 1 s Y Pb and Pr output terminals to the corresponding Y Pb Pr Component Video input terminals of a compatible TV e Switch your TV to the corresponding Component Video input to view your iPod s video playback e Press and hold gt II to toggle iPod video output between the connected TV and the iPod s own display screen Pb e If your particular iPod model does not support component video signal but supports composite video signal connect only VISO 1 s Pb output terminal to the corresponding composite video input of a compatible TV e Switch your TV to the corresponding Composite Video input to view your iPod s video playback Check with your iPod distributor which video signal your particular iPod model supports EXTENDED MODE When you dock your iPod into VISO 1 and a check mark appears and OK to disconnect is shown in the iPod display screen it means that your parti
2. position this will ensure reliable infrared remote control communications IDENTIFICATION OF CONTROLS ATTENTION Please make sure that the VISO 1 is powered off or unplugged from the mains power source before making any connections It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections POWER BUTTON Press this button to switch ON the VISO 1 When the POWER button is pressed the blue POWER indicator flashes continuously and then eventually gets fixed to blue Press again the POWER button to switch OFF the VISO 1 IDENTIFICATION OF CONTROLS 6 S Toggle S button to step through the Sources in the following order Docked iPod Bluetooth device and S PDIF input source device Press to increase the volume level to lower it 7 CONNECTOR COVER USB VISO 1 may need a software update to be in step with the latest technology trends Check with your authorized NAD distributors for Use to protect the pin connectors Remove before docking an iPod future software updates Only authorized NAD distributors or service IMPORTANT NOTE ABOUT THE PIN CONNECTORS centers are allowed to implement a software update Playback of a docked iPod maybe impaired if the pin connectors are dirty Connect to this input a USB memory stick containing the software Ensure that the VISO 1 pin connectors are clean free of any lint or any other up
3. DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL THE EQUIPMENT MUST BE CONNECTED TO AN EARTHED MAINS SOCKET OUTLET CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user s authority to operate this equipment NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment The symbol on the product user s manual and packaging point this out The materials can be reused in accordance with their markings Through re use recycling of raw materials or other forms of recycling of old products you are making an important contribution to the protection of our environment Your local administrative office can advise you of the responsible waste disposal point INFORMATION ABOUT COLLECTION AND DISPOSAL OF WASTE BATTERIES DIRECTIVE 2006 66 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION FOR EUROPEAN CUSTOMERS ONLY Batteries bearing any of these symbols indicate that they should be treated as separate collection and not as municipal waste It is encouraged that necessary Pb measures are implemented to maximize the separate collection of waste batteries a
4. SEE IT The model and serial number of your new VISO 1 are located on the back of the cabinet For your future convenience we suggest that you record these numbers here NAD is a trademark of NAD Electronics International a division of Lenbrook Industries Limited Copyright 2011 NAD Electronics International a division of Lenbrook Industries Limited iPod is a trademark of Apple Inc registered in the U S and other countries THANK YOU FOR CHOOSING NAD NAD VISO 1 The Music System Made for iPod The NAD VISO 1 is an inspired design married to the latest and most sophisticated audio technologies VISO 1 includes NAD s Direct Digital technology which offers two major advances in iPod music systems First it plays in its native digital format the music stored in the iPod completely bypassing the audio circuit limitations of the iPod Secondly the processing power inherent in Direct Digital technology optimizes the sonic performance of the loudspeaker VISO 1 has 2 way speaker system with electronic crossover and bi amplification that guarantees lowest distortion and widest frequency response As with all our products NAD s Music First design philosophy guided the VISO 1 design that it can confidently promise you both state of the art video technology and audiophile quality music listening for years to come We encourage you to take a few minutes now to read right through this manual Investing a little time here at the outse
5. VISO 1 Wireless Digital Music System Owner s Manual IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance with the manufacturer s instructions N QO uu BP WN 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use the attachments accessories specified by the manufacturer 12 Use only with a cart stand tripod bracket or table specified by the O manufacturer or sold with the apparatus When a cart is used use tae caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of tim
6. cular model can only be played back by VISO 1 in Extended Mode The following applies to your applicable iPod model in Extended Mode e The click wheel is non functional e Access to iPod menu is not possible e Playback of the first song automatically starts after docking the iPod VISO 1 FEATURES NEAR FIELD The NAD VISO 1 includes a special feature that subtly reduces the amount of high frequency power to optimize performance for near field listening You may prefer this setting if you listen at a very close distance or have a very small room For most installations the factory setting is correct NEAR FIELD SETUP 1 Press and hold S button until the blue POWER indicator flashes continuously 2 While the blue POWER indicator flashes continuously press Near field mode 3 VISO1 remains in Field mode and the blue POWER indicator remains flashing If there is no activity for 5 seconds the VISO 1 will default back to normal mode and the blue POWER indicator stops flashing ey to set RESTORING VISO 1 TO ITS FACTORY DEFAULT SETTINGS Sometimes power spikes and drop outs may from time to time cause some inadvertent functionality The procedure below will reset the VISO 1 to its factory default settings 1 Press and hold and then press POWER button to turn ON the VISO 1 2 Release when the POWER indicator turns red and flash three times VISO 1 will continue on to initialize www NADelectronic
7. date Use USB adaptor when necessary contaminations Ensure the same with the corresponding pin connectors of the iPod model you will be docking into the VISO 1 S PDIF OPTICAL Connect OPTICAL IN to corresponding optical output of sources 8 DOCKING CRADLE such as CD DVD or BD players digital cable box digital tuners and other applicable components COMPONENT VIDEO OUT Connect Component Video Out to the Component Video input of a Remove the dock s connector cover before docking an iPod player The docking cradle can be rotated 90 degrees allowing for portrait or landscape orientation of applicable iPod models Your iPod will be charged while it is docked to the VISO 1 compatible video monitor TV 9 POWER INDICATOR Be sure to observe consistency in connecting the Y Pb Pr jacks to the corresponding devices Refer also to the item about COMPONENT VIDEO OUTPUT at the VISO 1 FEATURES section AC MAINS INPUT The VISO 1 comes supplied with a separate detachable mains power cord There are 2 supplied power cords select applicable type for your usage Before connecting the plug to the mains powers source connect firmly first the other end to VISO 1 s AC Mains input socket Always disconnect the mains power plug from the mains power source first before disconnecting the cable from the VISO 1 s AC Mains input socket Power Rating 100 240V 50 60Hz 35W S Select through Sources When the POWER button
8. e 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 When disposing of used batteries please comply with governmental regulations or environmental public instruction s rules that apply in your country or area Batteries battery pack or batteries installed must not be exposed to excessive heat such as sunshine fire or the like CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITHIN THE PRODUCT S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE SERVICING INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE CAUTION RISK OF ELECTRIC SHOCK
9. is pressed the blue POWER indicator flashes continuously and then eventually gets fixed to blue The blue POWER indicator will flash when the source is changed or a remote control command is received VISO 1 REMOTE CONTROL Increase or decrease loudness level PPI Skip forward to the next song la Skip back to the previous song gt Il Start playback Pause playback temporarily Press and hold to toggle iPod video output between connected TV and iPod s own display screen applicable only to iPod models that support component video signal 4 Temporarily mutes audio output or restores audio from mute mode VISO 1 FEATURES SOURCE SELECTION B Use of S Source button VISO 1 source selection can be directed in two ways Toggle S button to step through the Sources in the following order A Hierarchical system Docked iPod Bluetooth device and S PDIF source device The three VISO 1 sources are automatically selected by the following order of priority Both source selection methods can be best described by the flowchart 1 Docked iPod below 2 Bluetooth device 3 S PDIF source device e An active Bluetooth device or an active source device connected to the S PDIF Optical input is immediately disconnected if an iPod player is docked in the VISO 1 The docked iPod player immediately takes priority over both devices and becomes the active source device e With no docked iPod player an active device connected to the
10. nd to minimize the disposal of batteries as mixed municipal waste X X End users are exhorted not to dispose waste batteries as unsorted municipal waste In order to achieve a high Hg Cd level of recycling waste batteries discard waste batteries separately and properly through an accessible collection point in your vicinity For more information about collection and recycling of waste batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items By ensuring compliance and conformance to proper disposal of waste batteries potential hazardous effects on human health is prevented and the negative impact of batteries and waste batteries on the environment is minimized thus contributing to the protection preservation and quality improvement of the environment WARNING The unit must not be exposed to dripping or splashing liquids and liquid filled objects such as vases or cups should not be placed on the unit CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user s authority to operate this equipment The disconnect device of the apparatus is its mains plug Cut off power to the apparatus by disconnecting its mains plug from the mains outlet The mains plug of the apparatus should be easily accessible or free from any obstruction during intended use RECORD YOUR MODEL NUMBER NOW WHILE YOU CAN
11. s com 2011 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved NAD and the NAD logo are trademarks of NAD Electronics International a division of Lenbrook Industries Limited No part of this publication may be reproduced stored or transmitted in any form without the written permission of NAD Electronics International VISO1_ENG_OM_V10 10 11
12. t might save you a good deal of time later and is by far the best way to ensure that you make the most of your investment in the VISO 1 One more thing We urge you to register your VISO 1 ownership on the NAD Worldwide Web site http NADelectronics com warranty For warranty information contact your local distributor NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL THE VISO 1 OWNER S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE CHECK OUT THE NAD WEBSITE FOR THE LATEST VERSION OF THE VISO 1 OWNER S MANUAL INTRODUCTION WHAT S IN THE BOX Packed with your VISO 1 you will find e Two detachable mains power cord one for European version models C version and one for North American version models AH version The VISO 1 remote control with 3V CR2025 battery VISO 1 Quickstart Guide SAVE THE PACKAGING Please save the box and all of the packaging in which your VISO 1 arrived Should you move or otherwise need to transport your VISO 1 this is by far the safest container in which to do so We ve seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton so please Save that box CHOOSING A LOCATION Choose a location that is well ventilated with at least several inches to both sides and behind and that will provide a clear line of sight within 25 feet 8 meters between the VISO 1 s front panel and your primary listening viewing

VISO 1 Owners Manual

Contents

Download Pdf Manuals

Related Search

Related Contents