Home

Manual - Gentex Corporation

1. 2 Open battery drawer by firmly pulling on side lip then sliding battery drawer open 3 Insert battery into drawer terminal side first Take care to make sure the appropriate terminal is aligned correctly terminal on battery to terminal on alarm metal contact and terminal on battery to terminal on the alarm metal contact 4 Rotate battery into drawer and close drawer Note the battery drawer will not close if the battery is installed incorrectly 5 Slide battery drawer shut until it is snapped into place 6 Use only Duracell MN 1604 battery with the GN 300 Series smoke alarm Available at many retail stores TANDEM WIRE YELLOW RED CAUTION Units with battery back up will not provide power or transmit an alarm to other AC only units in the event of an AC power failure All battery back up units in tandem with good batteries will operate normally during an AC power failure a minimum of 24 hours Figure 11 MOUNTING PLATE amp SMOKE ALARM 1 Lace the connector through the provided mounting plate and secure the plate to the junction box 2 Plug the wire connector into the smoke alarm base Figure 12 START FINISH SN SN WORK CONNECTOR WIRES BACK THROUGH HOLE IN ADAPTER PLATE ROTATE ALARM TO UPRIGHT POSITION 3 Place smoke alarm up to mounting plate rotating it clockwise until smoke alarm firmly snap locks into place Keep smoke alarm parallel to the mounting plate so tabs on plate se
2. Remove battery from smoke alarm Do not ship smoke alarm with battery still in battery drawer NOTE Remove anti tamper pins if installed 5 Carefully pack the manufacturer cannot be responsible for consequential damage and return to the manufacturer Include complete details as to exact nature of difficulties being experienced and date of installation 6 Return to Gentex Corporation 10985 Chicago Drive Zeeland Michigan 49464 Prior to returning call Gentex at 800 436 8391 or e mail FP_RMA gentex com to obtain a RMA Number from our return department LIMITED WARRANTY For a period of 12 months from the date of purchase or a maximum of 18 months from the date of manufacture Gentex warrants to you the original consumer purchaser that your Smoke Alarm will be free from defects in workmanship materials and construction under normal use and service If a defect in workmanship materials or construction should cause your Smoke Alarm to become inoperable within the warranty period Gentex will repair your Smoke Alarm or furnish you with a new or rebuilt replacement Smoke Alarm without charge to you except for postage required to return the Smoke Alarm to us Your repaired or replacement Smoke Alarm will be returned to you free of charge and it will be covered under this warranty for the balance of the warranty period This warranty is void if our inspection of your Smoke Alarm shows that the damage or failure was caused by abuse misuse ab
3. escape plans NOTICE Current studies have shown smoke alarms may not awaken all sleeping individuals and that it is the responsibility of individuals in the household that are capable of assisting others to provide assistance to those who may not be awakened by the alarm sound or to those who may be incapable of safely evacuating the area unassisted WHAT THIS SMOKE ALARM CAN DO This smoke alarm is designed to sense smoke entering its sensing chamber It does not sense gas heat or flames When properly located installed and maintained this smoke alarm is designed to provide early warning of developing fires at a reasonable cost This device monitors the air and when it senses smoke activates its built in alarm horn It can provide precious time for you and your family to escape from your residence before a fire spreads Such an early warning however is possible only if the smoke alarm is located installed and maintained as specified in this User s Manual NOTICE This smoke alarm is designed for use within single residential living units only that is it should be used inside a single family home or one apartment of a multi family building In a multi family building the device may not provide early warning for residents if it is placed outside of the residential units such as on outside porches in corridors lobbies basements or in other apartments In multi family buildings each residential unit should have smoke alarms t
4. OPENED PRODUCT WARRANTY BECOMES VOID NOTICE ONLY IVORY DISHWASHING LIQUID IS TO BE USED OTHER BRANDS ARE NOT RECOMMENDED AND MAY CAUSE YOUR SMOKE ALARM TO MALFUNCTION 6 Allow smoke alarm to soak for approximately 10 minutes longer if extremely dirty Then agitate for 5 or 10 seconds to flush out any remaining dirt left inside smoke alarm s housing 7 Remove smoke alarm from wash water and transfer directly to one of the first rinse buckets containing clear water Again allow smoke alarm to become completely submerged agitate once more for 5 or 10 seconds to remove soap residue 8 Finally transfer smoke alarm to your second and final rinse bucket repeating method found in Step 7 then remove smoke alarm to a clean dry area for a period of 48 hours to allow it to thoroughly dry NOTICE SMOKE ALARMS ARE TO BE AIR DRIED ONLY DO NOT PLACE SMOKE ALARM IN OVEN MICROWAVE OR USE A HOT AIR BLOWER TO ACCELERATE DRYING TIME THIS COULD RESULT IN DAMAGE TO YOUR SMOKE ALARM IMPORTANT IT IS RECOMMENDED TO CHANGE WASH AND RINSE WATER AFTER FIVE 5 SMOKE ALARMS IF YOUR SMOKE ALARMS ARE EXTREMELY DIRTY WATER SHOULD BE CHANGED MORE FREQUENTLY In the event you experience difficulty in the cleaning of your smoke alarm or if you have any questions please contact Gentex Corporation or your local Gentex distributor WARNING If the smoke alarm does not work properly do not try and fix it yourself This will void your warranty See T
5. be replaced for the following reasons Dust dirt and other environmental contaminants can affect your smoke alarm over a prolonged period Fast changing industry consensus standards and codes on all smoke alarms make it advisable to periodically upgrade your smoke alarm to maximize life safety Assurance that your smoke alarm needs are kept abreast with the constantly improving electronic technology Smoke alarms are recognized as one of the lowest cost ways to protect dwelling inhabitants against the danger of fire s It makes good common sense to periodically replace and update your smoke alarm that contributes so much to life safety MOUNTING LOCATION This smoke alarm can be mounted on a ceiling or wall with equal efficiency in either location Ceiling location smoke alarm should be mounted as close as possible to the center of a hallway or room Wall location locate the top of the smoke alarm not more than 12 inches from the ceiling Figure 5 NOTE NO MORE THAN 12 30 CM FROM CEILING Sg EAT AANA ASS dib BEST LOCATION lt gt ACCEPTABLE LOCATION Figure 5 RECOMMENDED SMOKE ALARM MOUNTING LOCATIONS Figure 6 NOT IN THIS AREA ANYWHERE IN THIS AREA 4 in 100 mm 36 in 910 mm i910 mn Figure 6 RECOMMENDED SMOKE ALARM LOCATION IN ROOMS WITH SLOPED GABLED OR PEAKED CEILINGS The placement of the smoke alarm is critical if maximum speed of fire detect
6. sparks Keep electrical appliances and cords in good working order and do not overload electrical circuits Keep stoves fireplaces chimneys and barbecue grills grease free and make sure they are properly installed away from combustible materials Keep portable heaters and open flames such as candles away from combustible materials 550 0324 Page 3 1 Do not allow rubbish to accumulate Do not leave small children home alone c Develop a family escape plan and practice it with your entire family especially small children Draw and post a floor plan of your home and find two ways to exit from each room There should be one way to get out of each bedroom without opening the door Teach children what the smoke alarm signal means and that they must be prepared to leave the residence by themselves if necessary Show them how to check to see if doors are hot before opening them how to stay close to the floor and crawl if necessary and how to use the alternate exit if the door is hot and should not be opened Decide on a meeting place a safe distance from your house and make sure that all your children understand that they should go and wait for you if there is a fire Hold fire drills at least every 6 months to make sure that everyone even small children know what to do to escape safely Know where to go to call the fire department from outside your residence Provide emergency equipment such as fire e
7. GENTEX GN 300 amp GN 303 CORPORATION A Smarter Vision SIGNALING LISTED PHOTOELECTRIC TYPE SINGLE STATION MULTI STATION SMOKE ALARMS AC POWERED WITH BATTERY BACK UP amp TANDEM WIRE CONNECTION Installation Instructions Owner s User s Information Manual READ CAREFULLY AND SAVE INTRODUCTION GN 300 SERIES The GN 303 Series smoke alarm is a photoelectric type unit for use as an evacuation device in residential and commercial residential applications while the GN 300 Series are for use as an alert and relocate device Each smoke alarm has a solid state piezo signal to warn and alert the household to the presence of threatening smoke Your photoelectric smoke alarm is designed to detect the smoke that results from an actual fire Consequently it is uncommon for household smoke such as cigarette smoke or normal cooking smoke to cause an alarm BASIC SAFETY INFORMATION AV Dangers Warnings Cautions and Notices alert you to important operating procedures or to potentially hazardous situations Pay special attention to these items WARNING This photoelectric smoke alarm is listed for use in single family and multi family residences along with hotels motels and other commercial residential occupancies This photoelectric smoke alarm must receive continuous 120VAC 60Hz pure sine wave electrical power NEVER ignore your smoke alarm if it sounds Refer to IF YOUR SMOKE ALARM SOUNDS section for more i
8. an the bedroom it is even less likely to wake up people sleeping in the bedroom In such cases the National Fire Protection Association recommends that the smoke alarms be interconnected so that a unit on any level of the residence will sound an alarm loud enough to awaken sleepers in closed bedrooms This can be done by employing a systematic approach by interconnecting smoke alarms together or by using radio frequency transmitters and receivers All types of smoke alarm sensors have limitations No type of device can sense every kind of fire every time These types of fires include 1 Fires where the victim is intimate with a flaming initiated fire for example when a person s clothes catch on fire while cooking 2 Fires where the smoke is prevented from reaching the smoke alarm due to a closed door or other obstruction 3 Incendiary fires where the fire grows so rapidly that an occupant s egress is blocked even with properly located smoke alarms In general smoke alarms may not always warn you about fires caused by violent explosions escaping gas improper storage of flammable materials or arson NOTICE This smoke alarm is not designed to replace special purpose fire detection and alarm systems necessary to protect persons and property in non residential buildings such as warehouses or other large industrial or commercial buildings It alone is nota suitable substitute for complete fire detection systems designed to protect i
9. at correctly into the smoke alarm 4 Remove dust cover after all construction is complete Dust cover must be removed prior to power being supplied to the smoke alarm If the dust cover is not removed operation of smoke alarm will be inhibited Figure 13 PUSH BUTTON HOLD UNTIL UNIT ALARMS POWER ON ALARM LIGHT CAUTION Remove dust cover before operating smoke alarm 5 ANTI TAMPER FEATURE The optional locking pins have been designed to inhibit tampering of the smoke alarm mounting and the battery drawer The GN 300 Series smoke alarms provide two independent anti tamper features one to lock the battery drawer and the other to secure the smoke alarm to the mounting bracket Depending on your application one or both features can be used A To secure the battery drawer remove pin from mounting bracket Figure 14 Figure 14 B Insert pin into locking hole found in back of the base With aid of needle nose pliers open locking hole insert pin and twist pin clockwise 1 4 turn Figure 15 Figure 15 Locking Hole C To secure smoke alarm to base remove pin from mounting bracket and insert into locking hole located in front opposite battery drawer With aid of needle nose pliers twist pin clockwise 1 4 turn Figure 16 Figure 16 te E CHECKOUT amp TROUBLESHOOTING 1 Supply house power to the smoke alarm The red indicator light should flash approximately every 15 30 seconds showing that the smok
10. e 3 Dining i Ge room Kitchen Bedroom D Bedroom Living room D Bedroom Figure 3 IN DWELLING UNITS WITH MORE THAN ONE SLEEPING AREA A SMOKE ALARM MUST BE PROVIDED TO PROTECT EACH SLEEPING AREA IN ADDITION TO SMOKE ALARMS REQUIRED IN BEDROOMS In addition to smoke alarms outside of the sleeping areas and in each bedroom NFPA 72 requires the installation of a smoke alarm on each additional level of the dwelling unit including the basement These installations are shown in Figure 4 The living area smoke alarm should be installed in the living room or near the stairway to the upper lever or in both locations The basement smoke alarm should be installed in close proximity to the stairway leading to the floor above Where installed on an open joisted ceiling the smoke alarm should be placed on the bottom of the joists The smoke alarm should be positioned relative to the stairway so as to intercept smoke coming from a fire in the basement before the smoke enters the stairway Figure 4 22 E E Bedroom Hall Bedroom Living l Dining room room A Basement Figure 4 A SMOKE ALARM MUST BE LOCATED ON EACH LEVEL IN ADDITION TO EACH BEDROOM IMPORTANT CONSIDERATION NFPA 72 2010 Edition Chapter 29 Section 29 8 1 4 5 b states Smoke alarms installed in one and two family dwellings shall not remain in service longer than 10 years from the date of manufacture Smoke alarms should
11. e alarm is operating properly 2 If red light is not flashing or the green LED is not on a Check that the battery is installed b Check the connector plug and wire connections NOTE Be sure you turn off power before checking wire connections c If the power supply and wiring check out but the red light does not flash or the green LED is still off return the unit to the manufacturer See TO RETURN A SMOKE ALARM 3 When powering up smoke alarms in a tandem installation and all the alarms sound immediately inspect all smoke alarms for a flashing red LED These will be the trouble units and should be replaced 4 To check for proper smoke entry into your smoke alarm s sensing chamber Gentex recommends using the Home Safeguard Smoke Alarm spray or CHEKKIT SMOKE Detector Tester from SDI This test should be performed once a year and smoke alarm spray should be sprayed from a distance no closer than 12 inches from the smoke alarm 550 0324 Page 3 5 MAINTENANCE After your smoke alarm has been in operation for a period of time or if it was installed prior to the completion of all building construction your device may have become more sensitive due to dirt build up in the smoke alarm s optic sensing chamber which could cause nuisance alarms or activation from small amounts of smoke build up If this should occur following this simple washing procedure will restore your smoke alarm back to its original condition For further informa
12. hese materials have been prepared by Gentex Corporation Gentex for informational purposes only are necessarily summary and are not purported to serve as legal advice and should not be used as such Gentex makes no rep resentations and warranties express or implied that these materials are complete and accurate up to date or in compliance with all relevant local state and federal laws regulations and rules The materials do not address all legal considerations as there is inevitable uncertainty regarding interpretation of laws regulations and rules and the application of such laws regulations and rules to particular fact patterns Each person s activities can differently affect the obligations that exist under applicable laws regulations or rules Therefore these materials should be used only for informational purposes and should not be used as a substitute for seeking professional legal advice Gentex will not be responsible for any action or failure to act in reliance upon the information contained in this material GENTEX CORPORATION 550 0324 CAC 10985 CHICAGO DRIVE ZEELAND MI 49464 02 01 05 PHONE 1 800 436 8391 www gentex com Pg 3 6
13. ion is desired Thus a logical location for a smoke alarm is the center of the ceiling At this location the device is closest to all areas of the room WHERE SMOKE ALARMS SHOULD BE INSTALLED IN MOBILE HOMES In mobile homes built after about 1978 that were designed and insulated to be energy efficient smoke alarms should be installed as described in the section above Figures 1 2 3 amp 4 are reprinted with permission from NFPA 72 National Fire Alarm Code Copyright 2002 National Fire Protection Association Quincy MA 02169 This reprinted material is not the complete and official position of the National Fire Protection Association on the referenced subject which is represented only by the standard in its entirety National Fire Alarm Code and NFPA 72 are registered trademarks of the National Fire Protection Association Inc Quincy MA 02169 550 0324 Page 3 3 In older mobile homes that have little or no insulation compared to today s standards uninsulated metal outside walls and roofs can transfer heat and cold from outdoors making the air right next to them hotter or colder than the rest of the inside air These layers of hotter or colder air can prevent smoke from reaching a smoke alarm Therefore install smoke alarms in such units only on inside walls 12 inches 30 cm from the ceiling If you are not sure about the insulation level in your mobile home or if you notice that the walls or ceiling are unusually hot o
14. ions of Article 300 3 b 210 of the National Electrical Code ANSI NFPA 70 as well as Article 210 2 Make wire connections to the supplied plug in connector as follows black to black white to white and connect the ground wire to the metal outlet box Figure 8 3rd UNINSULATED WIRE EARTH GROUND FOR NEUTRAL WHITE METAL BOXES ONLY NOTE YELLOW RED WIRE The yellow red wire from the smoke alarm is for tandem connection only DO NOT USE AND DO NOT REMOVE INSULATION CAP UNLESS CONNECTING ANOTHER SMOKE ALARM WIRING TWO OR MORE SMOKE ALARMS Tandem Installation NOTICE All smoke alarms in a tandem installation must be controlled by the same fuse or circuit breaker Otherwise tandem units will not operate Tandem will operate in the event of AC power failure if battery is connected to the smoke alarm LIMITATIONS A maximum of 12 smoke alarms GN 300 or GN 303 may be connected together Do not exceed 125 feet between each smoke alarm Do not exceed 1125 feet between first and last smoke alarm Wire used for interconnection shall be in accordance with article 760 of the latest edition of National Electrical Code NFPA 70 and must not exceed a resistance of 10 ohms TANDEM WIRE YELLOW RED FigDIes Tandem Wiring Diagram 2 ee ee QUICK DISCONNECT on a g eee LIMITATIONS Maximum of 12 smoke alarms may be connected together Do not exceed 125 feet between each smoke alarm Do not exceed 1125 feet between the first a
15. lose distance may be harmful to your hearing INSTALLATION GN 300 SERIES WIRING GENERAL 1 Use U L Listed cable with Class 1 insulation 2 Observe local code requirements Use box connector to anchor cable to outlet box 3 Metal outlet boxes must be grounded to earth ground 4 NOTICE Use only Duracell MN 1604 battery with the GN 300 Series smoke alarms Available at many retail stores CAUTION Turn off electricity to prevent SHOCK and damage to smoke alarm Be sure the power line to the smoke alarm is not controlled by any on off switch or other type of switch other than a fuse or circuit breaker IMPORTANT Insure that all fluorescent lighting fixtures are properly grounded NOTE The wiring to be used shall be in accordance with the provisions of Article 210 of the National Electrical Code ANSI NFPA 70 Wire installation should be performed only by a licensed electrician MOUNTING OUTLET BOX Use a 2 x 3 switch box or a 4 square or octagon junction box Mount a box for each smoke alarm If wall mounting is desired be sure the box screws are oriented to upper right and lower left corners Be sure to use supplied Mounting Plate WIRING ONE SMOKE ALARM 1 Run a minimum of 16 gauge 2 conductor cable plus ground 3 wires to the junction box from a power supply Smoke alarms shall be connected to their own dedicated circuit Use UL Listed Class 1 wire NOTE The wiring to be used shall be in accordance with the provis
16. nd last smoke alarm TO ADDITIONAL SMOKE ALARMS MAX 12 ALARMS PER SYSTEM NEUTRAL WHITE HOT BLACK 1 Run a minimum of 16 gauge 3 conductor cable plus ground 4 wires to the first junction box from a power supply and between all smoke alarms that are to be connected together Use UL Listed Class 1 wire Power limited cable for multiple tandem connections are available at many commercial electrical retail stores 2 Make wire connections to the supplied plug in connector as follows black to black white to white 3rd conductor to the yellow red wire The yellow red wire should be stripped to make the connection Connect ground wire between metal outlet boxes 550 0324 Page 3 4 Figure 10 p AN ANT 4th UNINSULATED WIRE EARTH GROUND FOR NEUTRAL WHITE METAL BOXES ONLY NOTES ON TANDEM INTERCONNECTING MODELS DO NOT connect Gentex Smoke Alarms to other manufacturers smoke alarms No more than 12 Gentex models GN 300 GN 303 may be connected in tandem All units connected in tandem MUST get their power from the same circuit that is all smoke alarms in tandem must be controlled by the same fuse or circuit breaker After installation to verify proper working conditions all horns must sound in this system CAUTION Failure to observe any of the conditions set forth may cause system malfunction and damage to the smoke alarm BATTERY INSTALLATION 1 Locate side mounted battery drawer
17. ndividuals in hotels and motels dormitories hospitals or other health and supervisory care and retirement homes Please refer to NFPA 101 The Life Safety Code and NFPA 72 for smoke alarm requirements for fire protection in buildings not defined as households Installing smoke alarms may make you eligible for lower insurance rates but smoke alarms are not a substitute for insurance Home owners and renters should continue to insure their lives and property PLACEMENT OF SMOKE ALARMS THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION S STANDARD 72 National Fire Protection Association Batterymarch Park Quincy MA 02269 For your information the National Fire Protection Association s Standard 72 reads as follows NFPA 72 2010 Edition Chapter 29 Section 29 5 1 Required Detection states the following 29 5 1 1 Where required by applicable laws codes or standards for a specific type of occupancy approved single and multiple station smoke alarms shall be installed as follows 1 In all sleeping rooms and guest rooms 2 Outside of each separate dwelling unit sleeping area within 6 4m 21ft of any door to a sleeping room the distance measured along a path of travel 3 On every level of a dwelling unit including basements 4 On every level of a residential board and care occupancy small facility including basements and excluding crawl spaces and unfinished attics 5 In the living area
18. nformation Failure to do so can result in serious injury or death Test this device once a week per manufacturer installation recommendation If the device ever fails to test correctly replace immediately If the device is not working properly it can not alert you to a problem This product is intended for use in indoor locations of family dwelling units MODELS SEE BACK OF SMOKE ALARM FOR EXACT MODEL GN 2 S00 ecco stvccsicetetcenens 120 VAC 60Hz FEUSING BS casiocuntabnaaiaiuaiicawosel 120 VAC 60Hz with temporal horn These units produce a non temporal audible alarm and are therefore not intended for locations where the desired action of the occupant s is evacuation Per NFPA 72 the American National Standard Audible Emergency Evacuation Signal as defined in ANSI 3 41 is required whenever the intended response is to evacuate the building NOTICE In the event AC Power fails a 9v battery will provide proper smoke alarm operation for a minimum of 24 hours ELECTRICAL SPECIFICATIONS OPERATING VOLTAGE 22 cee 120VAC 60Hz OPERATING CURRENT MAX 120VAC 9VDC 0 037 amps OPERATING AMBIENT TEMPERATURE RANGE 40 F to 1000F ALARM HORN RATING meets or exceeds 85dBA at 10ft HOW YOUR SMOKE ALARM WORKS The GN 300 Series smoke alarm operates on the photoelectric light scatter principle The unit s sensing chamber houses a light source and a light sensor The darkened sensing chamber i
19. normal usage faulty installation improper maintenance or repairs other than those performed by us ANY WARRANTIES IMPLIED UNDER ANY STATE LAW INCLUDING IMPLIED WARRANTIES OF MER CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLY ONLY FOR THE WARRANTY PERIOD SPECIFIED ABOVE PLEASE NOTE THAT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU Important Notice GENTEX WILL NOT BE LIABLE FOR ANY LOSS DAMAGE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING IN CONNECTION WITH THE SALE USE OR REPAIR OF THIS SMOKE ALARM PLEASE NOTE THAT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU If a defect in workmanship materials or construction should cause your Smoke Alarm to become inoperable within the warranty period you must return the Smoke Alarm to Gentex postage prepaid You must also pack the Smoke Alarm to minimize the risk of it being damaged in transit You must also enclose a return address Smoke Alarms returned for warranty service should be sent to Gentex Corporation 10985 Chicago Drive Zeeland MI 49464 If we receive a Smoke Alarm in a damaged condition as the result of shipping we will notify you and you must file a claim with the Shipper THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE T
20. o Return a Smoke Alarm for instructions to return smoke alarms that do not oper ate properly DO NOT TRY TO FIX IT YOURSELF IMPORTANT Gentex recommends smoke alarms be tested a minimum of once a week WARNING Never use an open flame of any kind to test your smoke alarm You may ignite and damage the smoke alarm as well as your home The test feature of your smoke alarm accurately simulates smoke conditions and tests the smoke alarm s functions as required by Underwriters Laboratories WARNING Do not cover tape or otherwise block the openings of your smoke alarm These openings are designed to allow air to pass through your smoke alarm thus sampling the air around the smoke alarm WARNING Smoke alarms are not to be used with detector guards unless the combination has been evaluated and found suitable for that purpose FAILURE TO REGULARLY CLEAN THIS SMOKE ALARM WILL RESULT IN FALSE ALARMS A BUILD UP OF DUST CREATES AN OBSCURATION THAT SIMULATES SMOKE THIS MEANS THE UNIT WILL GO INTO ALARM WITHOUT A FIRE CONDITION TO RETURN A SMOKE ALARM Should you experience problems with your smoke alarm proceed as follows 1 Turn off electrical power to the smoke alarm 2 Twist the smoke alarm counter clockwise to remove it from its mounting plate NOTE Remove anti tamper pins if installed 3 Unplug the connector from the back of the smoke alarm Do not remove the wire connection leave the connector for your replacement smoke alarm 4
21. o alert the residents of that unit Devices designed to be interconnected should be interconnected within one family residence only otherwise nuisance alarms will occur when a smoke alarm in another living unit is tested NOTICE WHAT SMOKE ALARMS CANNOT DO Smoke alarms will not work without power A battery must be connected to the smoke alarm to maintain proper device operation if AC power supply is cut off by an electrical fire an open fuse or circuit breaker or for any other reason In the event of AC power failure the battery will supply power for a minimum of 24 hours Smoke alarms may not sense fire that starts where smoke cannot reach the units such as in chimneys in walls on roofs or on the other side of closed doors If bedroom doors are usually closed at night smoke alarms should be placed in each bedroom as well as in the common hallway between them Smoke alarms also may not sense a fire on another level of a residence or building For example a second floor device may not sense a first floor or basement fire Therefore smoke alarms should be placed on every level of a residence or building The horn in your smoke alarm meets or exceeds current audibility requirements of Underwriters Laboratories However if the smoke alarm is located outside a bedroom it may not wake up a sound sleeper especially if the bedroom door is closed or only partly open If the smoke alarm is located on a different level of the residence th
22. off from the required alarms increases the escape time because the fire does not need to build to the higher level necessary to force smoke out of the closed room to the required alarms As a consequence it is recommended that the householder consider the installation of additional fire protection devices However it should be understood that NFPA 72 does not require additional smoke alarms over and above those called for in Figures 1 2 3 and 4 where required smoke alarms are shown ee D T Living room Basement Fa Indicates required smoke alarm Figure 1 ASMOKE ALARM MUST BE LOCATED ON EVERY LEVEL OF DWELLING UNIT INCLUDING BASEMENT WITHIN EACH SLEEPING ROOM AND OUTSIDE SLEEPING AREAS Where to Locate the Required Smoke Alarms The major threat from fire in a dwelling unit occurs at night when everyone is asleep Persons in sleeping areas can be threatened by fires in the remainder of the unit therefore smoke alarms are best located in each bedroom and between the bedroom areas and the rest of the unit as shown in Figure 2 Figure 2 Figure 1 Dining A Kitchen Bedroom Bedroom room Living room Bedroom Figure 2 ASMOKE ALARM MUST BE LOCATED BETWEEN THE SLEEPING AREA AND THE REST OF THE DWELLING UNIT AS WELL AS IN EACH BEDROOM In dwelling units with more than one bedroom area or with bedrooms on more than one floor more than one smoke alarm is required as shown in Figure 3 Figur
23. operation are 40 to 100 F 4 4 to 37 8 C In very dusty or dirty areas Dust and dirt can build up on the smoke alarm s sensing chamber and can make it overly sensitive or block openings to the sensing chamber and keep the smoke alarm from sensing smoke Near fresh air inlets returns or excessively drafty areas Air conditioners heaters fans fresh air intakes and returns can drive smoke away from smoke alarms making the devices less effective In dead air spaces at the top of a peaked roof or in the corners between ceilings and walls Dead air may prevent smoke from reaching a smoke alarm See Figures 5 and 6 for recommended mounting locations In insect infested areas If insects enter a smoke alarm s sensing chamber they may cause a nuisance alarm Get rid of the bugs before installing smoke alarms where bugs are a problem Near fluorescent light fixtures Electrical noise from nearby fluorescent light fixtures may cause a nuisance alarm Install smoke alarms and fluorescent lights on separate electrical circuits WARNING Never disconnect an AC smoke alarm to silence a nuisance alarm Open a window or fan the air around the smoke alarm to remove the smoke The alarm will automatically turn off when the smoke in the air is completely gone Do not stand close to the smoke alarm The sound produced by the smoke alarm is loud because it is designed to awaken you in an emergency Prolonged exposure to the horn at a c
24. r cold install the device on an inside wall Minimum protection requires one smoke alarm as close to the sleeping area as possible For better protection install one smoke alarm in each room but first read the Locations to Avoid LOCATIONS TO AVOID Nuisance alarms are caused by placing smoke alarms where they will not operate properly To avoid nuisance alarms do not place smoke alarms In or near areas where combustion particles are normally present such as kitchens in garages where there are particles of combustion in vehicle exhausts near furnaces hot water heaters or gas space heaters Install smoke alarms at least 20 feet 6 meters away from kitchens and other areas where combustion particles are normally present In air streams passing by kitchens Figure 7 shows how a smoke alarm can be exposed to combustion particles in normal air movement paths and how to correct this situation Figure 7 Bedroom Air Inlet Incorrect Living Room Bedroom In damp or very humid areas or next to bathrooms with showers The moisture in humid air can enter the sensing chamber as water vapor then cool and condense into droplets that cause a nuisance alarm Install smoke alarms at least 10 feet 3 meters away from bathrooms In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the smoke alarm Temperature limits for proper
25. rp will sound between the red LED flashes If AC power fails the green LED will turn off NOTE Tandem Interconnect Models When testing one smoke alarm the device that is activated will flash the red indicator light and sound its alarm horn All other units will sound the alarm horn with their red indicator lights remaining off FIRE PROTECTION PLAN WHAT YOU CAN DO TO MAKE YOUR FAMILY SAFE FROM FIRES This smoke alarm can quickly alert you to the presence of smoke it cannot prevent fire The ultimate responsibility for fire protection rests solely on you Installing smoke alarms is just the first step in protecting your family from fires You also must reduce the chances that fires will start in your home and increase your chances of safely escaping if one does start To have an effective fire safety program a Install smoke alarms properly following the instructions in this manual Keep your units clean Test your smoke alarm weekly and have unit repaired or replace unit when it no longer functions As with any electronic product smoke alarms have a limited life it is recommended that smoke alarms be replaced every ten years Smoke alarms that don t work cannot protect you b Follow safety rules and prevent hazardous situations Use smoking materials properly never smoke in bed Keep matches and cigarette lighters away from children Store flammable materials in proper containers and never use them near open flames or
26. s of a guest suite 6 In the living area s of a residential board and care occupancy small facility 29 5 1 2 Where the area addressed in 29 5 1 1 2 is separated from the adjacent living areas by a door a smoke alarm shall be installed in the area between the door and the sleeping room and additional alarms shall be installed on the living area side of the door as specified by 29 5 1 1 and 29 5 1 3 550 0324 Page 3 2 29 5 1 3 In addition to the requirements of 29 5 1 1 1 through 29 5 1 1 3 where the interior floor area for a given level of a dwelling unit excluding garage areas is greater than 93m2 1000ft2 smoke alarms shall be installed per 29 5 1 3 1 and 29 5 1 3 2 29 5 1 3 1 All points on the ceiling shall have a smoke alarm within a distance of 9 1m 30ft travel distance or shall have an equivalent of one smoke alarm per 46 5m2 500ft is evaluated by dividing the total interior square footage of floor area per level by 46 5m 500ft2 29 5 1 3 2 Where dwelling units include great rooms or vaulted cathedral ceilings extending over multiple floors smoke alarms located on the upper floor that are intended to protect the aforementioned area shall be permitted to be considered as part of the lower floor s protection scheme used to meet the requirements of 29 5 1 3 1 The installation of additional alarms of smoke heat or CO type should result in a higher degree of protection Adding alarms to rooms that are normally closed
27. s exposed to the atmosphere and designed to permit optimum smoke entry from any direction while rejecting light from outside the smoke alarm The light source is an infrared invisible LED which pulses every 8 seconds The light sensor is a photodiode matched to the light frequency of the LED light source Under normal conditions the light generated by the pulsing infrared LED is not seen by the light sensor as it is positioned out of the direct path of the light beam When smoke enters the sensing chamber light from the pulsing LED light source is reflected by the smoke particles onto the photodiode light sensor At the first sighting of smoke the device is put into a pre alarm mode This is indicated by a rapidly flashing red LED on the face of the smoke alarm Once the light sensor confirms smoke for 2 consecutive pulses inside the chamber the light sensor produces the signal necessary to trigger the device and sound the electronic horn HOW TO TELL IF YOUR SMOKE ALARM IS WORKING PROPERLY Your smoke alarm is provided with an alarm horn and flashing red Light Emitting Diode LED indicator which flashes every 15 30 seconds and a green AC power on LED Test button function when test button is pressed the full operation of the light source and light sensor is checked and will initiate an alarm If the battery is low or missing a chirp will be emitted when the red LED flashes If the smoke alarm is malfunctioning the chi
28. tion regarding frequency of cleaning and testing refer to NFPA 72 NFPA Batterymarch Park Quincy MA 02269 NOTICE Failure to follow full cleaning instructions could result in damage to this smoke alarm DO NOT remove all smoke alarms at the same time for cleaning 1 Turn off electrical power to the smoke alarm 2 Rotate the smoke alarm counter clockwise to remove it from its mounting plate NOTE If anti tamper pins have been installed they must be removed before rotating smoke alarm from mounting plate 3 Unplug the connector from the back of the smoke alarm Do not remove the wire connection leave the connector for your replacement smoke alarm NOTE If installed remove the anti tamper pins to the battery drawer Remove battery Do not open smoke alarm cover Doing so voids product warranty 4 Select three 3 standard size wash buckets and fill them each with one gallon of normal tap water distilled or de ionized treated water is recommended as a final rinse if water is extremely hard in your area 5 Add 1 8 cup of Ivory dishwashing liquid to the first bucket of water and allow it to mix thoroughly then place one dirty smoke alarm into the soap water mixture until it becomes completely covered or submerged NOTE If the smoke alarms are exceptionally dirty you may wish to first wipe off any excess dirt before washing unit so as not to dirty the wash water too quickly DO NOT open smoke alarm for cleaning IF SMOKE ALARM IS
29. xtinguishers and teach your family to use this equipment properly d Bedroom doors should be closed while sleeping if a smoke alarm is installed in the bedroom They act as a barrier against heat and smoke WHAT TO DO IF THERE IS A FIRE IN YOUR HOME If you have prepared family escape plans and practiced them with your family you have increased their chances of escaping safely Review the following rules with your children when you have fire drills so everyone will remember them in a real fire emergency If alarm should sound a Don t panic stay calm Your safe escape may depend on thinking clearly and remembering what you have practiced b Get out of the house following a planned escape route as quickly as possible Do not stop to collect anything or to get dressed c Open doors carefully only after feeling to see if they are hot Do not open a door if it is hot use an alternate escape route d Stay close to the floor smoke and hot gases rise e Cover your nose and mouth with a cloth wet if possible and take short shallow breaths f Keep doors and windows closed unless you open them to escape g Meet at your prearranged meeting place after leaving the house h Call the Fire Department as soon as possible from outside your house Give the address and your name i Never re enter a burning building Contact your local Fire Department for more information on making your home safer from fires and about preparing your family s

Manual - Gentex Corporation

Contents

Download Pdf Manuals

Related Search

Related Contents