Chapter 1 - Hardware
Contents
1. Removable 0 30 Snaps to standard 0 175 S 7 6 35 mm x 7 5 mm height DIN rail EN50022 pales i eo pint757035 eal mM vi S 2 25 Dia 0 175 4 4 Pou Use for direct panel mounting to a flat surface with up to 8 screw Removable 2 25 for direct panel 57 1 mounting A 0 39 9 9 Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 L 1 5 St rid Chapter 1 Hardware Mechanical Dimensions for 5 and 9 Port Unmanaged Models with Fiber in Metal Case Inches mm SE SW5U ST WT SE SW5U SC WT SE SW9U ST WT and SE SW9U SC WT Removable Screw Block Snaps to standard Phoenix 0 40 0 30 39mm x 7 5 mm height 0 175 p n 1757035 10 2 7 6 DIN rail EN50022 4 4 N e LLL a A JN 2 25 57 1 Dia 0 175 4 4 Use for direct panel mounting to 4 00 a flat surface with 101 6 up to 8 screw Removable for direct panel mounting 0 55 14 0 1 10 27 9 40 6 5 Port 9 Port l 1 6 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware ee ll Mechanical Dimensions for 5 Port Managed Model Inches mm SE SW5M REMOVABLE SCREW BLOCK PHOENIX P N 1757035 GROUND SCREW SCREW MOUNTING LOCATIONS DIM A TOP VIEW I 0A5 REMOVABLE FOR FLAT REMOVABLE 3 8 PANEL MOUNTING SCREW BLOCK PryP CEJ 1 07 27 1 RJ45 CONSOLE PORT 5 82 97 0 USB CONSOLE PORT BOTTOM VIEW Strid2. collisions and deterministic performance when tied with real time systems These industrial Ethernet switches can support 10BaseT 10 Mbps or 100BaseT 100 Mbps on their RJ45 ports Each of these ports will independently auto sense the speed and duplex mdi mdix crossover and polarity allowing you to use patch or crossover cables Managed switches include models that support gigabit Ethernet Some models include fiber optic ports or slots that accept SFP fiber optic transceivers 1 6 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware Safety Standards These industrial Ethernet switches meet the following standards plus others Electrical Safety CE per Low Voltage Directive and EN61010 1 IEC 1010 UL recognition per UL508 UL File E200031 CSA per C22 2 14 cUL File E200031 See Warnings on following page Install the Switches in accordance with local and national electrical codes Lightning Danger Do not work on equipment during periods of lightning activity Do not connect a telephone line into one of the Ethernet RJ45 connectors EMC emmissions and immunity e CE per the EMC directive EN 55022 or IEC 61326 1 or EN 61000 6 2 4 e FCC part 15 and ICES 003 Class B See FCC statement on following page Marine maritime and offshore These devices when installed in an appropriately IP rated enclosure Comply with DNV No 2 4 and equivalent Lloyds and ABS standard
3. 2 Groups A B C D and CE marked SFP option modules sold separately 1 M f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware n IG Managed Switch Accessories SFP Transceiver Part Number Description STRIDE 100Mb Small Form Factor Pluggable SFP transceiver module Transmit Receive Uses a long wavelength of 1310nm supports data transmission up SFP 4K FMF to 4km on a multi mode fiber LC duplex receptacle SFP Multi Source Agreement compliant 125Mbps IEEE802 3u 100Base FX compliant 125Mbps FDDI ISO IEC 9314 1 compliant STRIDE 100Mb Small Form Factor Pluggable SFP transceiver module Transmit Receive Uses a long SFP 30K FSF wavelength of 1310nm supports data transmission up to 30km on a singlemode fiber LC duplex receptacle SFP Multi Source Agreement compliant STRIDE Gigabit 1 25GB Small Form Factor Pluggable SFP transceiver module Transmit Receive Uses a short wavelength of 850nm supports data transmission up to 550 meters on a multi mode fiber SFP 500 GMF LC duplex receptacle SFP Multi Source Agreement E compliant 1 0625Gbps Fibre Channel FC PI 100 M5 SN I compliant 1 0625Gbps Fibre Channel FC PI 100 M6 SN I compliant 1 25Gbps IEEE802 3z 1000Base SX compliant 1 25Gbps IEEE802 3ah compliant STRIDE Gigabit 1 25GB Small Form Factor A AAL A eS eed Uses a long OK ial wavelength o nm supports data transmission up SFP 2K GM
4. 5 05 128 3 5 10 129 5 5 15 130 8 5 20 132 1 TOP VIEW REMOVABLE FOR FLAT PANEL MOUNTING REMOVABLE SCREW BLOCK 5 20 132 1 119 4 JU 0 80 20 3 9 9 1 60 3 82 40 7 97 0 RJ45 CONSOLE PORT USB CONSOLE PORT BOTTOM VIEW 1 20 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware Mechanical Dimensions for 8 Port Managed Gigabit Switch with Four SFP Ports Inches mm SE SW8MG 4P REMOVABLE SCREW BLOCK PHOENIX P N 1757035 GROUND SCREW TOP VIEW REMOVABLE REMOVABLE FOR FLAT rag PT SCREW BLOCK PANEL MOUNTING RJ45 CONSOLE PORT USB CONSOLE PORT SCREW MOUNTING LOCATIONS SCREW SIZE DIM A 5 05 128 3 6 i 8 5 10 129 5 5 15 130 8 5 20 132 1 BOTTOM VIEW Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 2 1 St rid Chapter 1 Hardware Mechanical Dimensions for 10 Port Managed Gigabit Switch with Two SFP Ports Inches mm SE SW10MG 2P 2 19 REMOVABLE REMOVABLE FOR FLAT l SCREW BLOCK PANEL MOUNTING SCREW MOUNTING LOCATIONS SCREW SIZE DIMA 5 87 149 1 5 92 150 4 5 97 151 6 6 02 152 9 22 f Stride Industrial Ethernet Switches User Manual REMOVABLE SCREW BLOCK PHOENIX P N 17570535 GROUND SCREW O TOP VIEW USB CONSOLE D PORT RJ45 CONSOLE c PORT BOTTOM VIEW 2nd Ed Rev A Chap
5. 5 or 8 Port SE SW5U amp SE SW8U Removable Screw Block Ph p n 1757035 gt Snaps to standard 35 mm x 7 5 mm height DIN rail EN50022 i 6 6 1 25 7 1 98 4 20 Dia 0 15 3 8 L 106 7 o Ue for e 3 95 100 3 panel mounting 1 98 5 z E o a flat surface i J OC IE 1 00 7 1 50 pi ee 3 26 0 06 25 4 38 1 82 8 1 5 5 Port 8 Port Mechanical Dimensions for 5 and 9 Port Unmanaged Models with Fiber in Plastic Case Inches mm SE SW5U ST SE SW5U SC SE SW9U ST and SE SW9U SC Removable Screw Block Phoenix p n 1757035 Snaps to standard 35 mm x 7 5 mm height DIN rail EN50022 4 35 Dia 0 15 3 8 110 5 Use for direct panel mounting o a flat surface 3 96 100 6 1 00 25 4 38 1 5 Port 9 Port 1 14 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware Mechanical Dimensions for 2 Port Media Converter in Plastic Case Inches mm Media Converters SE MC2U ST and SE MC2U SC Removable Screw Block Phoenix 0 40 Snaps to standard p n 1757035 35 mm x 7 5 mm height o j DIN rail EN50022 Dia 0 15 3 8 Use for direct panel mounting 3 96 100 6 o a flat surface T1 7 25 4 Mechanical Dimensions for 5 and 8 Port Unmanaged Models in Metal Case Inches mm 82 8 1 5 5 or 8 Port SE SW5U WT amp SE SW8U WT
6. cables Auto sensing operation Yes Full and half duplex Auto negotiating Yes 10BaseT and 100BaseT Yes on the TD and RD pair Automatic Ethernet isolation 1500 VRMS 1 minute Plug and play Yes Cable requirements Twisted pair Cat 5 or better shielded recommended Max cable distance 100 meters 328 ft Technical Specifications continued on the next page 3 2 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A St rid a Chapter 1 Hardware Technical Specifications cont d SC or ST Fiber Ports 100BaseF multimode 100BaseFX ports 1 on some unmanaged switch models 2 on some managed switch models Fiber port mode Multimode mm Fiber port connector Duplex SC or ST Optimal fiber cable 90 125 or 62 5 125 um for mm 9 125 um for sm Center wavelength 1300 nm Multimode Links up to 4 km typ 1300 nm use with 50 or 62 5 125 um fiber gt Transmitter power dB 21 min 17 typ 14 max gt Receiver sensitivity dB 34 typ 31 max Nominal max distance full duplex see web for details 4 km Half and Full Duplex Full duplex Ethernet Compliance 100BaseF Eye Safety IEC 60825 1 Class 1 FDA 21 CFR 1040 10 and 1040 11 SFP Small Form Factor pluggable Ports Note On the Gigabit MG models these ports are pluggable and accept any SFP Multi Source Agreement compliant transceiver Gigabit SF
7. nonhazardous especially when working in Class 1 Div 2 or Zone 2 hazardous locations e Power is off to the switch e The screw terminal block is unplugged This is especially important on the aluminum housed units as shown below Connecting or disconnecting wires to the screw block when its in place and power is turned on can allow the screwdriver to short the power to the case Unmanaged Models Single DC Power Redundant DC Power Chassis Chassis GND GND panel panel One DC Supply Dual DC Supplies Managed Models SE SW5M SE SW5M 2ST SE SW5M 2SC SE SW8M SE SW8M 2ST and SE SW8M 2SC Single DC Power Redundant DC Power One DC Supply Dual DC Supplies Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A 1 25 St rid Chapter 1 Hardware Managed Models SE SW16M and SE SW10MG 2P Single DC Power Redundant DC Power One DC Supply Dual DC Supplies SE SW8MG 4P Single DC Power Redundant DC Power Alarm Output ae Chassis Load Chassis opt GND opt GND panel panel One DC Supply Dual DC Supplies 1 26 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A St rid a Chapter 1 Hardware Communication Ports Wiring Overview The industrial Ethernet switches and media converters provide connections to standard Ethernet devices such as PLCs Ethernet I O industrial computers and much more RJ45 copper Ethernet ports and fiber optic Ethernet ports are availab
8. to let us know if we are reaching our goal If you cannot find the solution to your particular application or if for any reason you need technical assistance please call us at 770 844 4200 Our technical support group will work with you to answer your questions They are available Monday through Friday from 9 00 A M to 6 00 P M Eastern Time We also encourage you to visit our web site where you can find technical and non technical information about our products and our company http www automationdirect com If you have a comment question or suggestion about any of our products services or manuals please let us know Conventions Used When you see the exclamation mark icon in the left hand margin the paragraph to its immediate right A will be a warning or a caution This information could prevent injury loss of property or even death in extreme cases The words WARNING or CAUTION in boldface will mark the beginning of the text When you see the notepad icon in the left hand margin the paragraph to its immediate right will be a special note The word NOTE in boldface will mark the beginning of the text 1 2 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware Product Overview Stride Unmanaged Ethernet Switches Part Number Description STRIDE SlimLine Industrial Unmanaged Ethernet Switch with five 10 100Basel RJ45 Ethernet ports Redundant J power
9. F to 2km on a multi mode fiber LC duplex receptacle SFP Multi Source Agreement compliant IEEE 802 3 1000Base SX compliant STRIDE Gigabit 1 25GB Small Form Factor Pluggable SFP transceiver module Transmit Receive Uses a long cena th of eat sues cays 10K transmission up to 10km on a singlemode fiber SFP 10K GSF duplex receptacle SFP Multi Source Agreement compliant 1 0625Gbps Fiber Channel FC PI 100 SM LC L compliant 1 25Gbps IEEE 802 3 1000Base LX compliant STRIDE Gigabit 1 25GB Small Form Factor Pluggable SFP transceiver module Transmit Receive Uses a long wavelength of 1310nm supports data SFP 30K GSF transmission up to 30km on a singlemode fiber LC duplex receptacle SFP Multi Source Agreement compliant 1 25Gbps IEEE 802 3 1000Base LX compliant Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A 1 6 St rid Chapter 1 Hardware General Information Overview This user s manual will help you install and maintain the STRIDE industrial Ethernet switches and media converters Installation of these devices is very easy and they will begin to operate as soon as they are powered up Operation Unlike an Ethernet hub that broadcasts all messages out all ports these industrial Ethernet switches will intelligently route Ethernet messages only out the appropriate port The major benefits of this are increased bandwidth and speed reduction or elimination of message
10. HARDWARE In This Chapter INIFOOUCUION ooee esos 55 oe tetas et eee meee Soe soe ones Cee eyrererewen 1 2 Conventions Used 6 6 dh 8666 66D RRR d ae ee ee aed 1 2 Produc OVGIVICW sosro 4545044444445 Shee eae wen ees Stee eeeereess i 1 3 Managed Switch Accessories 6 6 6 66608 20a debe eee oew eres s eee ieee ee sews 1 5 General Information 25222245000 000000saer ree esaeeneteteeeee shennan e ee 1 6 LED INGICAlONrs 3c ead hone ook eG ORI Eees Chee eee ede ded ca 1 9 Installation Plastic Case Switches cece eee ee ee ee ee eee eee 1 11 Installation Metal Case Switches ccc ee eee eee ee ee ee eee 1 12 Power and Alarm Wiring 0 4 464 6 6 6 0645 9408945459 eu Daidaw eee gee o be 1 25 Communication Ports Wiring 2 ce cee ec ee eee eee eee eee 1 27 Technical Specifications 64 s6 u aoe8 46562 HOES HOT UE OHS EA ORO ee Se 1 31 St rid Chapter 1 Hardware Introduction The Purpose of this User s Manual Thank you for purchasing our Stride Industrial Ethernet Switches and Media Converters This manual describes AutomationDirect com s Stride industrial Ethernet switches and media converters their specifications included components and provides you with important information for installation connectivity and setup The manual shows you how to install wire and use the products Technical Support We strive to make our manuals the best in the industry We rely on your feedback
11. Input Voltage all models 10 30 VDC continuous Reverse Power Protection Yes Transient Protection 15 000 watts peak Spike Protection 5 000 watts 10x for 10 uS 34 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A St rid a Chapter 1 Hardware Technical Specifications cont d Environmental Storage Temperature Range 40 to 85 C 40 to 185 F Humidity non condensing 5 to 95 RH Electrical Safety UL508 CSA C22 EN61010 1 CE EMC emissions and FCC part 15 ICES 003 immunity EN55022 and or IEC61326 1 and or EN61000 6 2 4Typical 8 or 9 125 um for singlemode sm UL1604 CSA 622 2 213 Class Div 2 Hazardous Locations FN50021 EN60079 15 Zone2 CE ATEX Eye Safety fiber models een dee Fie A CFR RoHS and WEEE RoHS Pb free and WEEE compliant 1 09001 2000 Certified Total Quality company Mechanical Ingress Protection IP40 UL94V0 Lexan plastic for all plastic cased units Packaging and Protection Aluminum w protective finish for all metal cased units Dimensions L x W x H See mechanical drawings for details Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l i 3 5
12. OSION HAZARD CLASS 1 DIVISION 2 ZONE 2 WARNING WHEN IN HAZARDOUS LOCATIONS DISCONNECT POWER BEFORE EXPLOSION HAZARD REPLACING OR WIRING UNITS DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN WARNING EXPLOSION HAZARD SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS WARNING NOT SEPARATE ANY PART OF THE UNIT WHEN ENERGIZED USE THE EXPLOSION HAZARD UNIT FOR INTERNAL CONNECTIONS ONLY FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced r
13. P ports 2 or 4 depending on model Port Types Supported All SFP Multi Source Agreement compliant transceivers Note 100 Mbps fiber transceiver modules are also supported on these ports Ethernet Compliance 1000BaseT and 1000BaseF SX LX LH Eye safety IEC 60825 1 Class 1 FDA 21 CFR 1040 10 and 1040 11 B Note Refer to SFP module specifications for details specific to the SFP installed Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l li 3 3 St rid Chapter 1 Hardware Technical Specifications cont d OK Alarm Output Managed models only OK Output ON if P1 and P2 have power and switch software is running Voltage Same as switch input voltage Maximum Current Output 0 5 Amp Power Input Power Input Redundant Input Terminals SE MC2U SC 2 0W SE MC2U ST 2 0W SE SW5U 2 0W SE SW5U WT 2 0W SE SW5U SC 3 0W SE SW5U SC WT 3 0W SE SWO5U ST 3 0W SE SW5U SC WT 3 0W OE SW8U 4 0W SE SW8U WT 4 0W SE SW9U SC 5 0W SE SW9U SC WT 5 0W Input power typical with SE SWOL ST 5 0W all ports active at 100 SE SW9U ST WT 5 0W Mbps SE SW5M 3 6W SE SWOM 2SC 5 6W SE SWOM 2ST 5 6W SE SW8M 4 3W SE SW8M 2SC 6 3W SE SW8M 2ST 6 3W SE SW8MG 4P 12 0W No Fiber SE SW8MG 4P 15 0W With 4 Fiber plugged in SE SW10MG 2P 5 0W No Fiber SE SW10MG 2P 7 0W With 4 Fiber plugged in SE SW16M 7 0W
14. ST w H E connector for links up to 4km Redundant power inputs SE SW9U SC 3 m m m with surge and spike protection Auto crossover 35 mm SE SW9U ST WT H pii Hi DIN rail mounting Supports store amp forward wire speed SE SW9U SC WT 3 bl SE ir See and full duplex with flow control UL CSA CUL Note WT models have a metal case and are rated for a wider temperature range from 40 to 85 C STRIDE SlimLine Industrial Unmanaged Ethernet to Fiber Converter with one 10 100BaseT auto detecting r auto crossover and auto polarity RJ45 Ethernet Port and SE MC2U ST one 100BaseFX Fiber Optic Port ST or SC type multimode SE MC2U SC fiber connector for links up to 4km Redundant power Ji inputs with surge and spike protection 35 mm DIN rail mounting Supports store amp forward wire speed switching and full duplex with flow control UL CSA CUL amp CE Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A 1 3 St rid Chapter 1 Hardware Product Overview cont d Stride Managed Ethernet Switches Description Part Number SE SWSM 2ST SE SW5M 2SC STRIDE SlimLine industrial managed 5 port Ethernet switch metal housing 40 to 75 deg C operating temperature range five 10 100BaseT RJ45 Ethernet ports Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full dupl
15. adio TV technician for help Note All information in this document is subject to change without notice 1 82 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware LED Indicators Overview The Stride industrial Ethernet switches have 1 or 2 communication LEDs for each port and a power LED The managed models also have an OK output LED a status LED and dual power LEDs Managed Unmanaged The activity link and Managed speed LEDs e The activity are link and integrated stride A speed LEDs into a single are multi color integrated LED They are into the labeled for RJ45 ports each port number Power amp OK m nat LEDs See the ACT LNK and Speed 10 100 LED See the ACT LNK Speed LED explanation explanations that follow below amp on next page that follows on the next page Status LED Managed Models Only The Status LED indicates the overall health of the switch It is normally ON solid indicating that no internal CPU or software problems are detected It will flash when loading firmware and briefly on power up or reset Otherwise if it is OFF or flashing for an extended period of time then a problem is detected In this case please contact AutomationDirect for support Power LED On unmanaged models there is one power LED that is ON if either power input P1 or P2 has power applied to it On the managed models there are t
16. ased HTTP HTTPS SSL amp TSL Telnet SSH and more Industrial Protocols Modbus TCP EtherNet IP PROFInet Foundation Fieldbus HSE and others depends on model IEEE 802 3 802 3u 802 3ab z 802 3x 802 1D w 802 1p 802 1Q and others Management Interfaces managed models only Web text Telnet amp SSH CLI command line interface and SNMP see Chapter 2 Managed Switch Software for supported MIBs MAC addresses 1024 on unmanaged models 2048 on managed models with 5 8 or 9 ports 8192 on Gigabit models with more than 9 ports Memory bandwidth 3 2 Gbps on models with 9 or fewer ports 3 2 Gbps on models with more than 9 ports Latency for 10 Mbps ports 16 us frame time typical Latency for 100 Mbps ports lt 5 us frame time typical Ethernet isolation 1500 VRMS 1 minute Management Serial Port managed models only RS232 TXD RXD and GND 9600 8 N 1 fixed and or mini USB Varies on load and settings Technical Specifications continued on the next page Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 31 St rid Chapter 1 Hardware Technical Specifications cont d Copper RJ45 Ports 10 100 Mbps or 10 100 1000 Mbps Shielded RJ45 10 100 Mbps or 10 100 1000 Mbps depending on model Protocols supported All standard IEEE 802 3 Auto crossover Yes allows you to use straight through or crossover wired
17. cations activity On 10 100 ports a 100 Mbps connection is detected On 10 100 1000 ports a 1000 Mbps connection is detected On 10 100 ports a 10 Mbps connection is detected On 10 100 1000 ports a 10 or 100 Mbps connection is detected Indicates that there is not a proper Ethernet connection Link between the port and OFF aaa a device Make sure the cable has been plugged securely into the ports at both ends Flashing Green Yellow OK LED Managed Models This LED indicates the status of the power inputs There is an output screw terminal that can be connected as shown in the wiring diagram The output voltage between the screw terminal marked OK and the terminal marked will be the same as the applied switch input voltage The output will be ON when both the PI and P2 terminals have power applied to them It will be OFF if either input does not have power or the switch software is not running l 1 0 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware Installation Plastic Case Switches Overview These industrial Ethernet switches and media converters can be snapped onto a standard 35 mm x 7 5 mm height DIN rail Standard CENELEC EN50022 The switches and media converters can be mounted either vertically or horizontally Refer to the mechanical drawings that follow for proper mounting iS Note Make sure to allow enough room to route your Ethernet copper o
18. e Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 7 St rid Chapter 1 Hardware Mechanical Dimensions for 5 Port Managed Models with Fiber Inches mm SE SW5M 2ST and SE SW5M 2SC REMOVABLE SCREW BLOCK PHOENIX P N 1757035 SCREW MOUNTING LOCATIONS GROUND SCREW REMOVABLE FOR FLAT PANEL MOUNTING REMOVABLE SCREW BLOCK 520 132 1 a 4 70 119 4 0 51 12 9 107 9 9 27 1 3 82 97 0 RJ45 CONSOLE PORT USB CONSOLE PORT BOTTOM VIEW l 1 8 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware n Mechanical Dimensions for 8 Port Managed Model Inches mm SE SW8M REMOVABLE SCREW BLOCK PHOENIX P N PARA GROUND SCREW SCREW MOUNTING LOCATIONS SCREW SIZE DIM A 5 05 128 3 5 10 129 5 9 15 130 8 9 20 132 1 TOP VIEW 0 15 REMOVABLE 3 8 REMOVABLE FOR FLAT SCREW BLOCK TYP PANEL MOUNTING 5 20 66 0 132 1 4 70 3 82 97 0 RJ45 CONSOLE PORT USB CONSOLE c PORT 0 BOTTOM VIEW Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 19 St rid Chapter 1 Hardware Mechanical Dimensions for 8 Port Managed Models with Fiber Inches mm SE SW8M 2ST and SE SW8M 2SC REMOVABLE SCREW BLOCK PHOENIX P N 1757035 GROUND SCREW SCREW MOUNTING LOCATIONS SCREW SIZE DIM A
19. ex with flow control UL CUL1604 Class Div 2 Groups A B C D and CE marked STRIDE SlimLine industrial managed 5 port Ethernet switch metal housing 40 to 75 deg three 10 100BaseT RJ45 Ethernet ports and two multi mode 100BaseFX fiber ports ST or SC type multimode fiber connector for links up to 4km Redundant power inputs with surge and Spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full duplex with flow control UL CUL1604 Class Div 2 Groups A B C D and CE marked STRIDE SlimLine industrial managed 8 port Ethernet switch metal housing 40 to 75 deg C operating temperature range eight 10 100BaseT RJ45 Ethernet ports Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full duplex with flow control UL CUL1604 Class Div 2 Groups A B C D and CE marked SE SW8M 2ST SE SW8M 2SC SE SW8MG 4P SE SW10MG 2P STRIDE SlimLine industrial managed 8 port Ethernet switch metal housing 40 to 75 deg six 10 100BaseT RJ45 Ethernet ports and two multi mode 100BaseFX fiber ports ST or SC type multimode fiber connector for links up to 4km Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports E Store and Forward wire speed switching and full duplex with flow control UL CUL1604 C
20. inputs with surge and spike protection Auto SE SW5U in oe 39 LIRA a N ae ate hh amp 2 i orward wire speed switching and full duplex with flow SE SDL ol control UL CSA CUL amp CE Note WT models have a metal case and are rated for a wider temperature range from 40 to 85 C STRIDE SlimLine Industrial Unmanaged Ethernet Switch with eight 10 100BaseT RJ45 Ethernet ports Redundant m power inputs with surge and spike protection Auto SE SW8U si i o 35 ae al aan al amp p orward wire speed switching and full duplex with flow ESEA l control UL CSA CUL amp CE Note WT models have a metal case and are rated for a wider temperature range from 40 to 85 C STRIDE SlimLine Industrial Unmanaged Ethernet Switch with four 10 100BaseT RJ45 Ethernet Ports and one a r s 100BaseFX Fiber Optic Port ST or SC type multimode fiber SE SW5U ST 7 Tol G connector for links up to 4km Redundant power inputs SE SW5U SC li nt HE and ue protection deme 35 a Z ST rail mounting Supports store amp forward wire spee aaa al a i ng and full duplex with flow control UL CSA CUL K i E t i Note WT models have a metal case and are rated for a wider temperature range from 40 to 85 C STRIDE SlimLine Industrial Unmanaged Ethernet Switch l with eight 10 100BaseT RJ45 Ethernet Ports and one mm a ee ae 100BaseFX Fiber Optic Port ST or SC type multimode fiber SE SW9U
21. lass Div 2 Groups A B C D and CE marked STRIDE SlimLine industrial managed 16 port Ethernet Switch metal housing 40 to 75 deg C operating temperature range sixteen 10 100BaseT RJ45 Ethernet ports Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full duplex with flow control UL CUL1604 Class Div 2 Groups A B C D and CE marked STRIDE SlimLine industrial managed 8 port Ethernet switch all Gigabit metal housing 40 to 75 deg eight 10 100 1000 BaseT RJ45 Ethernet ports and four advanced combination SFP ports that accept noise immune fiber optic links up to 40 km Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full duplex with flow control UL CUL1604 Class I Div 2 Groups A B C D and CE marked SFP option modules sold separately STRIDE SlimLine industrial managed 10 port Ethernet switch with Gigabit metal dasa 40 to 75 deg seven 10 100 BaseT RJ45 Ethernet ports three Gigabit 10 100 1000 BaseT RJ45 port and two advanced combination SFP ports that accept noise immune fiber optic links up to 40 km Redundant power inputs with surge and spike protection auto crossover 35 mm DIN rail mounting Supports Store and Forward wire speed switching and full duplex with flow control UL CUL1604 Class Div
22. le depending on model RJ45 Ethernet Wiring Use data quality not voice quality twisted pair cable rated category 5e or better with standard RJ45 connectors Straight through or crossover Ethernet cable can be used for all devices the switch is connected to because all the ports are capable of auto mdi mdix crossover detection The RJ45 Ethernet port connector bodies on these products are metallic and connected to the Chassis GND terminal Therefore shielded cables may be used to provide further protection To prevent ground loops the cable shield should be tied to the metal connector body at one end of the cable only Electrical isolation is also provided on the Ethernet ports for increased reliability Straight thru Cable Wiring Cross over Cable Wiring B Note For reference only Either cable wiring will work Ethernet Plug amp Connector Pin Positions RJ45 Cable Distance The maximum cable length for 10 100BaseT is 100 meters 328 ft Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 2 7 St rid Chapter 1 Hardware Ethernet Fiber Wiring Guidelines Depending on the model these industrial Ethernet switches may include one two or four fiber optic ports All 100 Mbps fiber ports are available with dual SC or ST multimode style connectors Refer to the technical specifications for details All 1000 Mbps fiber ports are provided as SFP small form
23. llowing AutomationDirect PLC Ethernet Modules are not compatible with the Stride Ethernet switches and Media Converters with fiber optic connections because the modules have a speed of 10BaseF fiber optic only Ethernet Communications Module p n H2 ECOM F amp H4 ECOM F Ethernet Base Controller Module p n H2 EBC F amp H4 EBC F Ethernet Remote Master Module p n H2 ERM F amp H4 ERM F Verifying Connectivity After all Ethernet and or fiber connections are made check the LEDs corresponding to the ports that each of the devices are connected to Ensure that for each port that is in use the LED is on or blinking If a port LED is off go back and check for connectivity problems between that port and the network device connected to that port In addition the color of the LED should indicate the speed at which your device is connected see prior section on LEDs Serial Console Port Wiring An optional way to configure the managed switch is through the RJ45 console RS232 port Wire a serial console cable as shown below to make a connection between a COM port on your PC DB9 male and the RS232 port of the managed switch RJ45 female Switch RJ 45 Serial Configuration Cable PC Serial Port Serial Port i RJ45 8 pin 1 do not use Papac S 2 do not use 3 do not use 4 Signal GND 5 RXD 6 TXD 7 do not use 8 do not use 12345678 Wiring Diagram shield 1 do not use 2 RXD 3 TXD 4 do not u
24. ows for quickest installation and optimal utilization of rail space B Vertical screw to panel mount This mounting option gives better shock and vibration resistance C Flat screw to panel mount This mounting option offers a low profile orientation in shallow boxes plus the best shock and vibration resistance The power connection terminal block is removable for access to the mounting tab Important Notes about Thermal Performance Stride switches with metal cases use an innovative technique to remove excess heat from the product and its components This technique effectively utilizes the heavy gauge all aluminum case as a large heat sink Therefore the case may be warm during operation especially with heavy loads such as all ports linked and active This is normal operation For best performance it is recommended that a DIN rail spacer such as end clamp part number DN EB35 be used between the switch and any adjacent device This will leave an air gap for best heat dissipation off the case For best thermal performance when direct panel mounting to a metal surface thermal compound may be used between the switch and mounting surface This will reduce any air gaps and optimize the transfer of heat from the case to the mounting surface Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 13 St rid Chapter 1 Hardware Mechanical Dimensions for 5 and 8 Port Unmanaged Models in Plastic Case Inches mm
25. pluggable These accept plug in fiber transceivers that have an LC style connector They are available with either multimode or singlemode transceivers Refer to the technical specifications for details For each fiber port there is a transmit TX and receive RX signal When making your fiber optic connections make sure that the transmit TX port of the switch connects to the receive RX port of the other device and the receive RX port of the switch connects to the transmit TX port of the other device Use standard fiber optic wiring techniques not covered by this manual to make your connections The corresponding ACT LNK LED will be ON solid or flashing when you have made a proper connection Fiber Ports on Switches 1 28 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Stride Duplex Operation The RJ45 ports will auto sense for Full or Half duplex operation the fiber ports are configured for full duplex operation On managed switches the duplex setting is software configurable Chapter 1 Hardware Note Fiber devices with half duplex settings will communicate with the switch in most situations Network Device Check The industrial Ethernet switches and media converters support 10 100BaseT or 10 100 100 Base T on the RJ45 copper ports and 100BaseFX or gigabit Ethernet on the fiber optic ports depending on model Make sure you connect the appropriate devices to each port Note The fo
26. r fiber optic cables Mounting Removal DIN Rail Mounting DIN rail mounting steps 1 Hook top back of unit over the DIN rail 2 Push bottom back onto the DIN rail until it snaps into place DIN rail removal steps A Insert screwdriver into DIN clip and pry until it releases from the DIN rail B Unhook top of unit from DIN rail Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 1 1 St rid Chapter 1 Hardware Installation Metal Case Switches Overview These industrial Ethernet switches can be snapped onto a standard 35 mm x 7 5 mm height DIN rail Standard CENELEC EN50022 They can be mounted either vertically or horizontally Refer to the mechanical drawings that follow for proper mounting Note Make sure to allow enough room to route your Ethernet copper or fiber optic cables DIN Rail Mounting Mounting Removal DIN rail mounting steps 1 Hook top back of unit over the DIN rail 2 Push bottom back onto the DIN rail until it snaps into place DIN rail removal steps A Push the unit down to free the bottom of the DIN rail B Rotate the bottom of the unit away from the DIN rail C Unhook top of unit from DIN rail 1 1 2 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware oT Mounting Options Stride switches with metal cases offer the following optional mounting methods A Vertical DIN rail mount This mounting option all
27. s For marine and maritime compliance do not install this product within 5 meters of a standard or a steering magnetic compass WEEE compliance These devices comply with the WEEE directive Dispose of properly RoHS compliance These devices comply with the RoHS directive and are considered lead and other hazardous substance free Hazardous Locations e CE per ATEX directive and EN50021 EN60079 15 Zone 2 EEx nA II T4 X 40 C lt T 85 C e UL per UL1604 Class 1 Div 2 Groups A B C D UL File E200031 e CSA per C22 2 213 Class 1 Div 2 Groups A B C D cUL File E200031 See Warnings on following page Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l l1 St rid Chapter 1 Hardware Installation and Hazardous Area Warnings Warnina These products should not be used to replace proper safety interlocking No software based device or any other solid state device should ever be designed to be responsible for the maintenance of consequential equipment or personnel safety In particular AutomationDirect com disclaims any responsibility for damages either direct or consequential that result from the use of this equipment in any application All power input and output 1 0 wiring must be in accordance with Class I Division 2 wiring methods and in accordance with the authority having jurisdiction WARNING SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR EXPL
28. se 5 Signal GND 6 do not use 7 do not use 8 do not use 9 do not use Note Use the above wiring diagram to make your own cable We recommend using 22 AWG shielded cable Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A 1 29 St rid Chapter 1 Hardware USB Console Port Wiring The managed switches also have an USB port alternative to the RS232 port Use a standard USB cable with a mini USB plug on one end and an A type USB plug on the other end The A type plug goes into a standard USB port on a computer The mini USB plug goes into the USB port on the switch The USB driver is available for download at automationdirect com RS23 RJ45F RS232 RJ45F r fe Note The RS 232 and or USB ports may be located on the bottom edge or front face of the switch 1 30 f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Stride Technical Specifications Chapter 1 Hardware Technical Specs Here are the hardware technical specifications for the industrial Ethernet switches and media converters covered by this manual Ethernet switch type General Specifications Unmanaged or Managed Operating mode Store amp forward wire speed switching non blocking Devices supported All IEEE 802 3 compliant devices are supported Protocols managed models only SNMPv1 v2 v3 RMON DHCP SNTP TFTP STP RSTP QoS CoS ToS DS IGMPv1 v2 VLAN tag and port b
29. ter 1 Hardware n IG Mechanical Dimensions for 16 Port Managed Model Inches mm SE SW16M REMOVABLE SCREW BLOCK PHOENIX P N 1767035 GROUND SCREW 54 5 REMOVABLE REMOVABLE FOR FLAT PANEL MOUNTING SCREW BLOCK SCREW MOUNTING LOCATIONS SCREW SIZE DIM A 5 87 149 7 5 92 150 4 I 5 97 151 6 TY Port 6 02 152 9 USB CONSOLE PORT RJ45 CONSOLE BOTTOM VIEW Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A l 1 2 3 St rid Chapter 1 Hardware Mechanical Dimensions for SFP Transceiver Modules Inches mm SFP 4K FMF SFP 30K FSF SFP 500 GMF SFP 2K GMF SFP 10K GSF and SFP 30K GSF 1 2u f Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A Chapter 1 Hardware i SSS EN Power and AlarmWiring Overview DC voltage in the range of 10 to 30 VDC 3 0W needs to be applied between the P1 plus terminal and the Minus terminal as shown below To maintain a UL 508 panel listing use a Class 2 power supply The chassis screw terminal should be tied to panel or chassis ground To reduce down time resulting from power loss these industrial Ethernet switches can be powered redundantly with a second power supply as shown below Screw Torque When tightening the screws be careful to tighten to a max torque of 5 Ib in 0 57 Nm Wire size should be between 24 AWG and 12 AWG Before performing any wiring to these switches make sure e The area is currently
30. wo Power LEDs that indicate if there is power applied to the respective input Explanation of LED Indicators continued on next page Stride Industrial Ethernet Switches User Manual 2nd Ed Rev A 1 9 St rid Chapter 1 Hardware ACT LNK LED This is the Yellow LED on models with two LEDs per RJ45 port ON yellow Indicates that there is a proper Ethernet connection Link between the port and another not flashing Ethernet device but no communications activity is detected ON yellow Indicates that there is a proper Ethernet connection Link between the port and another flashing Ethernet device and that there is communications activity Indicates that there is not a proper Ethernet connection Link between the port and OFF Ta a device Make sure the cable has been plugged securely into the ports at both ends Speed 10 100 LED This is the Green LED on models with two LED s per RJ45 port ON green A 100 Mbps 100BaseT connection is detected OFF A 10 Mbps 10BaseT connection is detected ACT LNK Speed LED This is a bi color Green Yellow LED on models with one LED per RJ45 port Indicates that there is a proper Ethernet connection Link between the port and another ON Solid not flashing Ethernet device but no communications activity is detected Indicates that there is a proper Ethernet connection Link between the port and another Ethernet device and that there is communi
Download Pdf Manuals
Related Search