One-door Access Controller
Contents
1. 10 digit or 8 digit machine auto identify Add multi card by input card No zone Programming Password 24 inputstartcardNo cardQty Card Qty is 4 digit If one time add twenty cards input 0020 Add card PIN Programming Password 3 readcard PIN If modify PIN see 3 5 Delete user by input User ID No Programming Password 42 inputUserIDNo About User ID No see 3 4 Delete user by input card No Programming Password 43 inputcardNo Card No is 10 digit or 8 digit machine auto identify Delete user by input PIN Programming Password 44 inputPIN PIN is 3 6 digits Delete all PIN users Programming Password 45 1111 Use to PIN users Do not include Card users and Card PIN users Change Open time Programming Password 5 XX XX can be 2 digit and the max is 99 If input 00 the signal output time is 0 2 Secs Set Open mode Programming Password 6 XX XX can be 01 only card 02 card or Access Password 03 card PIN Reader setting For options Programming Password 6 04 The machine can be used for reader W26 output Security function Setting Programming Password 7 XX XX can be 01 02 Security function OFF ON and 03 04 Anti dismantle alarm OFF ON Anti dismantle Alarm setting For options Remark Security Function ON means System would be locked for 5 Minutes if continue to read illegal card or input wrong Access Password for 10 times Backlight setting For options Programming Password 8 XX XX can be 02. 1 02 03 Normal ON Normal OFF Auto Reset Factory Default Programming Password 8 99 Except Programming Password and Manager Card Set Manager Card Programming Password 91 readMAC readMDC First read card is Manager Add Card and Second read card is Manager Delete Card 3 2 To reset to Factory Programming Password 123456 Step1 Turn off power and connect bin 2 amp 3 of RST S1 Step2 Turn on power and buzzer gives 3 long buzz with green light flash fast 3 4 User ID No explain User ID is auto generating 4 digit number started at 0001 The number increases with adding user one by one and ignores deleting user Common Access Password has no ID If need to set Manager Card now read two empty cards first one as Manager Add Card and Second one as Manager Delete Card with red light flashing and continuous short buzz Step3 Turn off power disconnect bin2 amp 3 and connect bin 1 amp 2 of RST Step4 Turn on power again 3 3 How to use Manager Card MAC amp MDC To add a card user in standby mode read MAC read new cards read MAC To delete a card user in standby mode read MDC read registered cards read MDC To delete all users in standby mode read MDC read MAC read MDC Remark User cards can be added or deleted continuously 3 5 How to change PIN When open mode card PIN After reading card and input correspondin
3. 2 llati ide One door Access Controller nstallatons Guide NO Mark Color Function User Manual V2 0 F ay Red T 1 Specifications 2 GND Black Power 1 1Technical parameters 3 PUSH Blue Low level output NO Item Value 4 OPEN Yellow Door Release 1 Operating voltage DC 12V 10 5 BELL Grey BELL 2 Operating current lt 100mA 6 BELL Purple BELL 3 Dimensions 125mmx84mmx22mm 7 DATAO Green WG DATAO 4 Weight 300g 8 DATA1 White WG DATA1 5 Ambient temperature 10 C 60 C 9 NC Brown Relay NC output 6 Relative humidity 20 80 10 COM Orange Relay Com output 7 Storage 1000users 11 NO Pink Relay NO output 8 Card type alternative EM ID card IC card for options 9 Card reading distance 1 8CM Wiring diagram 1 2 Factory Default Programming Common Access 123456 None Password Password Z Relay Unlock Backlight Auto for options 5 Seconds output W26 port Input for options Security mode OFF Card or Access Password Open mode Access Password include Private Access Password PIN and Common Access Password 1 3 Light and Sound indicates Light red and green Light Description Access control status Red light flash every 1 sec Slow flash Red light is always ON Green light is always ON within Open time Green light flash every 0 5sec Fast flash Holding state Programming state Unlocking state Pending
4. further action Sound buzz Description Indicates 1 short buzz Valid input Invalid input 3 short buzz 1 long buzz Program success Remark If let relay drive electric lock please connect a reverse diode with the lock s and poles Continuous long buzz Restoring factory programming passwords 3 Programming Guide 3 1 Detailed Programming Guide Programming Password Default 123456 all password can be 3 6 digits Purpose Operation Remark Basic Change Programming Password Programming Password 0 new Programming Password If Programming Password lost perform 3 2 to reset to Factory Default 123456 Function New Programming Password Add user card Programming Password 1 readcard If add multi cards read cards continuously Set Common Access Password Programming Password 21 new Common Access Password Common Access Password is only one Open method Common Access Password Delete all users Programming Password 40 0000 Delete all cards and PIN except Common Access Password Delete user by read card Programming Password 41 readcard If delete multi cards read cards continuously a Add Private Access Password PIN Programming Password 22 PIN PIN can be more Unlock door method PIN Add card by input card No Programming Password 23 inputcardNo Card No is
5. g PIN to open the door within 5 seconds long press until the green new PIN new PIN lights flash fast and then input new PIN changed successfully with a long buzz
Download Pdf Manuals
Related Search