Operating and maintenance manual for Bubble King® DeLuxe
Contents
1. 4 Ifthe skimmer produces a water air mixture in the tube when it is turned on this means that the skim mer is operating correctly The skimming default must lie elsewhere 5 Do not let the pump run dry this would lead to permanent damage 6 A sufficient pre filtering of the water before it en ters the skimmer is recommended So the pump will be spared as before large parts such as snail shells or shells which can lead to a blockage of the needle wheel Depending on how high is the water fill level in the filter the Bubble King DeLuxe can be placed on the right height to achieve an optimal result of skimming Since 1986 Kk kkk Nozzle with air and ozon plug D Do not forget At least 20 30 mm are required for take off and cleaning of the complete skimmer pot For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 8 Defects and claims for compensation disclaimer 8 Defects and claims for compensation 8 1 Barring any further claims we are only liable that the supplied goods are free of defects until the initial transfer of perils Insignificant variatio2. pumps For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de has a so called ideal operation point The ideal point is well defined and will be found as shown below Please turn to completely screw nozzle as on the upper left picture shown Then please turn to the nozzle to the left counter clockwise Usually 1 1 turn This is the best operating point The black dots are used only for orientation The user may exceed or under run this point as desired Under running the point may be advisable to reduce the skimmer performance in coral tanks with only a few fish In creasing the flow through may be advisable on tanks with many fish or in the case of disaster A dying big Tridacna algae emitting spores or poisoning triggered by dying ani mals or similar reasons require a fast and wet foaming Notice Each spin increases water flow through by approx 500 litres Operation without nozzle screw is prohibited The air flow would be reduced by half and water flow would be increased by 300 In this state the pump will be overloaded and within a short time automatically switched off The noise l
3. showing upwards Wheel unit with slide and the counter part on the motor shown on the picture on the left For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 3 Disassembling and cleaning the riser tube of the skimmer All internal Bubble King skimmers can be totally disas sembled Thanks to new production processes with a pre cision range of 100 mm all CNC machined parts have a so called zero fit This means that most of the parts are not bonded to each other but feature precise fits All screws are made from pure titanium grade 2 and are absolutely seawater resistant and rustfree i 5 x D After cleaning reseat the tube into the bearing fig left below and tighten softly Attention Do not overtighten the screws in the base plate Untighten the screw from the jet pan with an Philips tip screw driver Please detach the skimmer in the filter tank as far as pos sible Remove the pump pull out the telescope tube and unscrew the skimmer head Please prevent the head from falling off sideways Clean the parts as far as possible by a soft material and decalcify if necessary
4. skimmed water volume redu ia ball valve gi f II Important Do not posi tion the levelling pipe backflow of the skimmed water of the external skimmer either above or below the wa ter level of the filter unit There is a high risk that the filter unit will idle Note If the geometrical levelling tube sets back a long horizontal sec tion an angle should be used to ensure a safe process For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 2 Maintenance We recommend the cleaning of the Bubble King DeLuxe at frequent intervals respectively to check the needle wheel for foreign objects To check the needle wheel it is not necessary to remove the internal skimmer from the filter tank Unplug the skimmer from the mains Remove the jet tube from its seating Turn the skimmer into your direction and optically check the first row of needles for foreign objects like snails mussels activated carbon pellets filter cotton or food debris In case of an accumulation of debris in the pump the pump must be disassembled Red Dragon Bubble King pumps have a buil
5. Please do not use sharp abrasive or acid cleansers because the plexiglass is sensitive to scratches tion plate cannot be removed from the riser tube Access for cleaning is available through the upper opening fig right below 3 1 Disassembling the plexiglas riser tube from the base plate only internal skimmers From the date of manufacturing as 2007 05 Bubble King skimmers are not glued to the base plate anymore but firmly fixed by screws This allows lifting the riser tube from the base plate to make the innards accessible to thor Hint for an optimal cleaning The skimmer tube should be rinsed under flowing water with some chlorine Chlorine doesn t damage the skimmer parts ough cleaning Please proceed as follows ch z First untighten the 3 screws with an adequate screw driv Ads Ye oe er Lift the tube from the base plate Caution The PVC linkers are very sensitive DO NOT DROP For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 4 Maintenance of the skimmer head PVC thread All Bubble King skimmers have a CNC milled PVC thread providing 100 tightness of th
6. and to demand the return of the skim mer In general every examination of damages is bound to lump sum compensation if it occurs that the customer has to be accounted for the damages 8 8 Spare parts Our liability to deliver and hold spare parts available is limit ed to the period of 5 years after initial shipment of the prod uct Our respective list prices apply for spare parts 8 9 Disposal We offer our customers to take back products that fall under the restriction of hazardous substances directive ElektroG within Germany free of charge for products which were brought into circulation after the 13th of August 2005 We will take care for the disposal If a customer chooses not to let us take care for the disposal he takes the responsibility of a disposal according to legal regulations and discharges us from our liabilities according to 10 sect 2 ElektroG and any associated liabilities of others 8 10 Subject to alterations The manufacture has the right for changes in hardware and software of the product at any time without preliminary no tice as long as these changes advance reliability or quality of the skimmer No claims can be made if for instance de sign functionality or performance of the skimmer changes elementary The assured specification of the skimmer is always guaranteed Pince 1956 Kk kkk 9 Manufacturer s declaration Titles against Royal Exclusiv concerning the products described in this m
7. de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 1 3 Installation and connection of the external skimmer The external Bubble King DeLuxe skimmer functions exactly like the internal one Unless otherwise stated all instructions listed in the handbook for internal skimmers also apply for external skimmers However there is great difference in terms of the connec tion because the external Bubble King DeLuxe skimmer requires a delivery pump which supplies the skimmer and the skimmer pump with the water to be filtered Please re fer to the data specification of your external skimmer for information regarding the power of the delivery pump It is also important to note that the external skimmer should be positioned no lower or higher than the filter unit or water level See left sketch below Note If possible the water sucked in by the delivery pump should be roughly filtered ahead to avoid unnecessarily polluting or contaminating the delivery and skimmer pumps with snail shells or pieces of coral for example which could wear the pin wheel or impeller and or lead to a defect Water fill level in filter unit E BO Backflow of the
8. Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 ince 1986 info royal exclusiv de www royal exclusiv de KKKKK Operating and maintenance manual for Bubble King DeLuxe For all Bubble King DeLuxe protein skimmer 200 250 300 400 500 and 650 internal external Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 Since 1986 info royal exclusiv de www royal exclusiv de KKKKK Operating and maintenance manual for Bubble King DeLuxe For all Bubble King DeLuxe protein skimmer 200 250 300 400 500 and 650 internal external 1 Commissioning putting into operation general ane eee eect eeeeeeteeeeeeeees 1 1 Setting the adjustable nozzle only internal skimmer uae cece eececeeeeeeeeeees 1 2 Regulating the water level stripline in the skimmer cup by the torque tube internal and external skimmer lk eceeeccecceeeeeee ees 1 3 Installation and connection of the external Skimmer ____u eee eccececeeteeeeeeeeee es 2 Maintenance y he re nrrer ree er era 2 1 Disassembling the pump intent te eteeeceeteeeeeeeeeees 2 2 Deliming and cleaning the impeller id deceaetaeesaeeseeeeeeeaaees 3 Disassembling and cleaning the riser tube of the internal skimmer __ eeeeeeeeeee eee 3 1 Disassembling the plexiglas riser tube from the base plate occ eecceeeeeeeeeeee ees 4 Maintenance of th
9. ack up devices for the case of a potential malfunction or failure of the pump 8 3 The customer has to check the goods immediately thoroughly also for product safety Apparent damages have to be reported in written form immediately Hidden damages have to be reported immediately after their dis covery The customer is liable to report transport damages within 24 hours to the carrier and or the delivery service Disregarding the rules for checking and reporting results in a loss of warranty 8 4 Furthermore we are not liable for the consequences of inappropriate application usage maintenance and han dling of the product by the customer or his subsidiaries neither for normal abrasion This applies specifically to the consequences of thermal chemical electrochemical or electrical influences as well as for infringements against our uses and maintenance manuals The same applies to damages which are the result of changes or adjustments by the customer which have not been approved by us in beforehand 8 5 Our liability for wanton negligence is limited to claims of injury of life body and health to claims based upon the law on product liability and to claims from culpable funda mental breach of the contract which peril contractual obli gations For the rest our liabilities for wantonly negligent breach of contractual obligations which are foreseeable at the time of the conclusion of the contract are barred Damages which are unam
10. anual adress on the Royal Exclusiv guarantee clauses Specification may vary due technical improvements 9 1 Manufacturer Royal Exclusiv pumps and skimmers Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de Made in Germany Royal Exclusiv EAR number WEE Reg No 83082352 9 2 Informations and support Thank your for purchasing a Royal Exclusiv Bubble King protein skimmer This protein skimmer is a high qual ity product made in Germany with the highest manufactur ing demands on modern CNC maschines This manual is supposed to help you to setup the protein skimmer for use and to advice you with the necessarily maintenance pro cedures To ensure longlasting satisfaction with this product we please you to read this manual carefully and follow our guidelines Royal Exclusiv guarantees 5 years of spare part availability for the Bubble King DeLuxe protein skimmer Should the device in some way not meet the high demands you expect from Royal Exclusiv please contact the dealer where you purchases your Bubble King DeLuxe protein skimmer This is usually the best way for product support However you may feel free to contact our support on our website http www royal exclusiv de For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv
11. biguously attributed to inappro priate usage of the product are in general to be accounted for by the customer In the case of returns of the product the customer has to use break proof packaging for the product The customer is liable for any damages that can be accounted to an inappropriate packaging For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 8 6 Claims against us become time barred within a year after the initial delivery of the goods to the customer The same applies to claims for damages regardless of their ju ridical cause The limitation period does not apply to claims based upon the malicious concealment of damages from the injury of life health or body and for other damages that result out of intention or wanton negligence 8 7 If it becomes apparent during our examination of dam ages reported by the customer or in the course of our re moval of defects that the reported damages or claims were made wantonly negligent or unwarranted we may charge an adequate consideration for our examination and for the removal of defects The customer has the right to neglect a necessary repairing
12. de All information subject to change We try our best but printing errors reserved
13. e designed to provide high water flow through to the skimmer All Bubble King DeLuxe models have an integrated drain on the skimmer head see right fig above The drain al lows you to remove and clean the skimmer head and drain Pince 1956 Kk kkk the foam residue adsorbate The drain tubing had been sealed factory side by a cone shaped silicone plug On the client side the drain may be prolonged by a hose or tubes to feed the adsorbate into a tank into a bucket or directly into the sewer We recom mend keeping the adsorbate drain permanently closed Notice Please do not wait too long until cleaning an over filled pot By problems caused by low water level The pump inlet must not cause a swirl like shown on the fig on the left below to prevent permanent damage to the pump Please do not use a 90 degrees angular tube but a 90 degrees arch Due to the deflection angles are reduc ing the performance more than 50 compared to an arch The nozzle has been trimmed to 40 0 mm to allow easy installation of an arch 1 1 Setting the adjustable nozzle only internal skimmers All internal Bubble King skimmers are fit with an adjust able water inlet nozzle Using the nozzle mainly adjusts the water flow rarely affecting the air performance Please note A skimmer performs best when a perfectly well defined amount of water and air enters the skimmer on the lowest point of the device The Bubble King Red Dragon
14. e head in stalled to the skimmer tube After every thorough cleans ing the thread should be lu bricated by some silicone grease or oil which makes the head much easier to spin The surface of the seal should be also treated by some oil which allows a smoother seating of the E head and adds more tightness The seal itself was made from silicone and thus is permanently salt water proof 5 Maintenance of the resonator silencer Bubble King skimmers are extremely low noise The noise of the air jet is perfectly dimmed by a valuable reso nator The so called Helmholtz Resonator reduces noise by frequency phase shifting The Royal Exclusiv resona tors are mostly maintenance free because the air is not forced through filters like in other devices but smoothly pass through the resonator Dusty air or accidentally dipping the resonator into salt water may require an internal cleaning to prevent plugging from accumulated salt crystals Please check the resonator for obstructions by manual ly blowing through it If you experience some resistance please proceed as follows Open the resonator by the use of a matching M5 tool Thoroughly clean the resonator and reassemble The left figure below shows the opened resonator Pince 1986 Kk kkk Thoroughly clean the resonator and reassemble The cel lular material is only helpful for noise reduction but must not be replaced if not desired Please do not overtighten
15. e skimmer head PVC thread an eaeeeceeeeteeeeseeeeaeeeens 5 Maintenance of the resonator silencer 2 ncaa eteteeeeaeeeeaeeeeeeees 6 emer ae eee nanena Ot OZOM OU er 6 2 Good to KC W ase reieeettrrte reee elec T Possible sources of error tate tteteeeetaneeeeeseaees 8 Defects and claims for compensation disclaimer iudcceceeeeeeeteeteeeaeeeeees 9 Manufacturer s declaration inate ttetaaeeteeseeeeseaees 9 1 Manufacturer ee beeeieteseeccce eed 9 2 Informations and support nc teteeteeeeteeeeeaeeaeeees Important Notice Please read this manual carefully before you install the device We recommend not to proceed the installation of the device until you read the manual This prevents any questions and problems that might occur in installation process As soon as you power on the skimmer for the first time you agree that you read and understood this manual In doubt or if anything is unclear please contact your supplier vendor or dealer before you start up the skimmer For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 1 Commissioning putting into operation Please take the Bubble King out of t
16. evel also would exceed dramatically 1 2 Regulating the water level stripline in the skimmer cup by the torque tube internal and external skimmer It is also possible to adjust the water level in the skimmer by help of the wedge shaped tube Basically we recom mend to set the water level with the telescope tube The wedge shaped tube should be only used for fine tun ing or flooding of the skimmer head In this case flooding means the cleaning of the Bubble King head without re moving the head The wedge shaped tube must be almost closed forcing the water level immediately into the skimmer head Now use a brush to clean the riser tube to flush the residue into the skimmer head without draining back into the filter tank The O ring shown on the left upper figure should be lubri cated by silicone oil from time to time to keep spinning of the wedge shaped tube easy The O ring also prevents salt and water drain from the T set which would complicate spinning the tube The position of the wedge shaped tube is shown by two black dots If both dots are aligned like shown on the right figure the wedge shaped tube is opened 100 ince 1986 Kk kkk Spinning the tube to the left or to the right like shown on the figure will fine tune the foam level lt The figure below shows how the water outflow can be regulated by turning the torque tube oa For more information please visit www royal exclusiv
17. ews of the internal pumps external V4A were made from titan and thus are 100 salt water proof Pince 1956 Kk kkk Use your fingers to grab behind the needle wheel and soft ly pull the wheel from its guidance Clean the wheel by the help of a sharp tip for example with a Nail file Please decalcify the wheel unit in an applicable decalcify ing bath DO NEVER use hydrochloric acid even when thoroughly diluted The pump may be seriously damaged Applicable are formic acid acetic acid and phosphoric acid or even household decalcifiers for water conditioners and coffee machines Basically the wheel bearing of the motor should be also decalcified Thick greasy residues should be removed under running water by the help of a semi hard brush Attention Please consider the safety regulations imprinted when using decalcifiers Please wear protective clothing and safety glasses For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de Core nee E j wi 4 ranr h n Ea M ig 4 a lt FA k AT z ja i We recommend to check the Red Dragon pump already after th
18. he package and check the skimmer for shipping damage which must be filed to your local dealer within 24 hours The Bubble King is preinstalled and ready for operation and may be put into the filter sump for instant operation omly internal Please install the skimmer head and put the skimmer into the filter sump or equivalent to get famil iar to the device The lower water level of the Bubble King should not be below 15 cm and shouldn t exceed 30 cm The best matching water level is between 20 and 25 cm Under some circumstances the water level may be above 30 cm but this will prevent adjusting of the foam level Now please plug the power cable into the desired wall out let Please note that sub water level pumps must be only connected to a ground fault circuit interrupter FI safety switch Furthermore we recommend a frame connector with voltage surge protection which in the case of a short circuit in the mains prevents a high voltage boost to the Red Dragon pump which will burn the internal fuse In the case the RD fuse melting fuse was blown the motor can t be repaired and therefore must be replaced Please note that it is absolutely prohibited to cut the plug from the power cable to prolong or short the power line Sub water pumps with cut power cables do not meet the safety regulations and any warranty on the device will be void Furthermore we are not allowed to repair sub water pumps if the power cable j wa
19. installation operation and maintenance By using this manual you agree that in no circumstances the manufacturer can or will be held liable for any personal injuries or property damages which possibly occur due to the usage of the device This applies specifically for any damages that are due to inappropriate piping or plumbing Insufficient or missing cleaning or maintenance intervals and damages that might result due to these are not cov ered by warranty This applies especially for calcinations salt water usage and accumulated foreign particles pond usage such as sand or gravel which lead to damages on rotors bearings rotor housing or motor housing that are not covered by warranty Pince 1956 Kk kkk 8 2 Our warranty for defects is strictly limited to supple mentary performance This is upon our choice either re moval of defects or replacement delivery free from defects In the case of challenge impossibility or failure of the sup plementary performance the customer has the right for im pairment or the right to withdraw from the contract Additional expenses which arise because the customer has brought the sales item to another place than his subsidiary The manufacturer explicitly limits the warranty to the pump itself We are not reliable for consequential damages or damages that are caused by a malfunction or failure of the skimmer such as a loss of animals It is in the responsibility of the customer to provide b
20. ns of the contracted appearance and workmanship or marginal limitation of the usability or suitability of the product are unremarkable The warranted condition endurance and usability the prod uct is solely subject to the specification agreed in writing in the product specification and or in this manual Further oral agreements especially from preliminary talks adver tising and or in related industrial standards will are only valid as integral part of a written contract Only conditions and specifications assured specifically by us are valid We do not accept conditions or specifications made by third parties Specifically the specification assured in this manual are valid If the customer wants to use the product for other than the intended purpose he is obliged to thoroughly the suitability of the product for the other purposes We give no warranty and no liability accrues for any applications that are not agreed on by us explicitly and in written form Any manipulation of the pump the needle whell impeller or the electronic as well as any attempt to modify the soft ware to influence the software or to read out or re engineer the software of the driver unit immediately causes a loss of warranty and all claims and rights expire Every user is held responsible for the appropriate usage of his Bubble King DeLuxe skimmer The user manual does not discharge you from your liability for a safe appro priate and secure application
21. ree months to determine the possible maintenance intervals that can be depending on precipitation between 2 12 months If the impeller group extremely calcified solve the plate between engine and rotor Cover enter with a small slot screwdriver carefully 2 2 Deliming and cleaning the impeller If the bearing fits on the shaft like shown on the picture on the left when pulled out then manually remove it from the shaft And the bearing after removal from the shaft shown on the picture on the right Pince 1956 Kk kkk Important notice The backside bearing of the wheel unit should have your special attention because most failures result from there i A Under no circumstances put the bearing loosely onto the shaft and then insert the wheel unit into the motor block The bearing wont fit in its slide and thus the pump will hum extremely after putting into operation The bearing must securely installed into its slide before assembling the wheel unit After the bearing was installed into its slide the O ring seal must be seated by the help of a mid size screw driver After thoroughly rinsing of all decalcified parts with water we now begin to reassemble the device At first check if the bearing sleeve of the wheel unit on the back was seated properly Now take the wheel unit and position in a way that the rectangular slide shows upward This rectangular slide will fit into the motor only when
22. s manipulated After running the pump within a short time a foam cushion should be formed like shown on the right figure above Let the skimmer run for several hours without placing the pot on top Pince 1956 Kk kkk In general new skimmers require a certain amount of time to produce firm foam New skimmers may contain several substances like grease glue residue and similar substances which pre vent foam forming Depending on the contamination of your aquarium water it may take from 2 minutes to 1 week until solid foam was formed A proper prediction when your skimmer was run in can t be made If the skimmer doesn t produce solid bubbles this is due to a normal degreasing process which can t be shortened Shown in the figure below During this process move the telescope tube to the lowest level which is the F stop of the tube holder This will prevent instant overflow while the j skimmer performs its n initial operation _ _ Telescope tube lowered Telescope tube lifted For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de If the foam was solid enough adju
23. st the water level in the skimmer by lifting the telescope tube There is a small screw on the side of the wedge shaped tube to secure the tube into its holder Please never use a tool and do not overtighten the screw Please note that the telescope tube can t be 100 waterproof Before installing the skimmer head make sure the inter nal red O ring was perfectly seated without ripples or simi lar irregularities These may lead into leakage On the figure above Current water level you can see the water level stripline approx 5 cm below the maximum level This water level stripline can be lowered or rised by turning the tube The water level stripline is different in ev ery aquarium depending on quality and surface tension of the salt water The water level should be within the cone and the lower end of the skimmer head This line ensures a dry foaming Our recommendation is a guideline not a must and thus the line may be exceeded in some cases It behoves to the user to decide whether he prefers wet or dry foam The Bubble King water drain Originally the drain tubing of the Bubble King is not fixed by gluing We do not recommend any gluing of the tubes The tubes can be set into any direction but we do not recommend putting the water drain into the environment of the pump inlet because this will provide treated water to the pump which will drastically decrease the perfor mance Basically the filter should b
24. t in automat ic shutoff The internal circuit is permanently measuring the pumps power consumption In the case of serious cal cifying and thus stiff bearings the internal circuit will clas sify the rising power consumption as a failure and switch off the pump due to safety reasons Because of this be haviour a Bubble King pump never can be damaged by smouldering fire or other damage due to a short circuit Just plug off and on to bring the pump back into operation Please note that it is not advisable to trick the internal circuit into normal operation by a repeated switching of the device If a Red Dragon pump was switched off a failure occurred apparently which must be solved If happened usually only a cleaning session is required IMPORTANT Permanently tricking the circuit may result in severe motor damage which will not be covered by warranty 2 1 Disassembling the pump After removing the pump from the silicone hose please remove the inlet nozzle from the designated opening Put the skimmer onto a flat soft surface or a towel and start to disassemble the pump as shown below You just need a standard mid size screw driver and an Allen wrench M5 required for a complete disassembling Turn off the 4 housing screws and remove the head Caution Thepumpholdersaremadefromplastic Justtighten the screws until the gap between pump head and holder was closed Overtighten the screws may damage the threads The housing scr
25. the screws 6 General Important correctly seated adjustable nozzle only internal The noozle fits tightly into a notch and is removable After cleaning the nozzle please check that it was completely pressed into the notch like shown in the left figure The nozzle must be firmly seated If the nozzle was not firmly seated the consequences are equal to a wide open noz zle screw causing huge water flow and turbulences in the skimmer 6 1 Ozon plug Please remove the hose from below the resonator and in stall a 12mm T set auf Install another hose on the lower end of the T set The 12mm T opening must be reduced to 6mm and fitted with a nozzle Plug the ozoniser to the small nozzle Usually the depression of the Bubble King pump is suf ficient to provide enough suction to the ozone If the hose is too long you may use a small air pump to feed the air ozone mix into the skimmer Under no circumstances try to connect the 10mm silicone hose from the Bubble King pump directly to the ozoniser It is definitely not functional The high resistance of ozonisers make it impossible to be directly driven through the pump The skimmer per formance would be instantly reduced by 90 The pump would be overloaded and the safety circuit will emergency shut off the pump to prevent damage to the pump For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info ro
26. yal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 6 2 Good to know We state explicitly that the pump must not dry run Further more it is not allowed even for testing purposes to switch on the pump in a dry state Resulting damage to bearings and or axles are not subject to warranty Royal Exclusiv products are manufactured on state of the art CNC milling machines Our staff is all well trained care fully working master craftsmen In the case of complaints or improvements please contact our service at info royal exclusiv de We are glad to help you Royal Exclusiv guarantees a permant supply of spare parts for at least 5 years 7 Possible sources of error To get an optimal skimming result the following informa tions are important 1 Water does not become water straight away As a result of the different composition the skimmer may need a few days before it starts to skim Particularly with new products 2 Note water filling level from 150 mm up to 300 mm ideally 225 mm this is the height of the water in the filter basin 3 The water level in the skimmer is controlled using a tube This sets the amount of foam to be produced The level of water in the skimmer is set by turning it left or right
Download Pdf Manuals
Related Search