Original - Sumed International
Contents
1. Lock Unlock This is used to prevent the user from accidentally changing the control panel settings The button can lock the existing settings status Press again to unlock Please note the ON Standby button will also be locked as an additional safety feature however the Auto Firm Nursing button cannot be locked Display Where a dot appears after a reading this means that the panel is unlocked to enable the system to be reset adjusted When there is no dot the reading is a display of the pressure being EE supplied to cells which are being inflated This is an indication of the Comfort setting 2 Integrity Mattress Components CPR Control The CPR Cardio Pulmonary Resuscitation Control is at the head end position of the mattress and ee Integrity comprises the following componens is identified by the clearly marked pull tag This allows the air to be evacuated in approximately Detachable Cover 10 seconds The standard protective cover is a 2 way stretch cover zipped on 4 sides to a durable anti slip base The zips a Emergency CPR Deflate With the patient lying down pull down hard on the tag pictured are protected by flaps to prevent ingress of fluid and allow easy removal of the cover for cleaning or right for quick deflation replacement b Remember to replace the CPR tag when resuming operation or the unit will not inflate Cells c Pull open the CPR tag to deflate non alternating air cells for storage2. ity hai Integrity has 29 separate welded double height cells lrawepor control 10x blue non ventilated cells on both rows Sees The Transport Control facility is enabled b 19 x grey ventilated micro air loss cells on the top row non ventilated cells on the bottom row p y y disconnecting the air supply tubes from the pump and re connecting the male and female ends together This gives a 58 cell construction including 19 micro air loss cells coloured grey and printed Ventilated less than 10 Litres per hour 5 at the head 5 at the feet and 9 in the central area Pump Power lead Detachable Cover Air Tubes 19x Ventilated Cells Double height cell construction 10 x Non ventilated Cells Foam Insert 3 Clinical Applications Indications Integrity is suitable for patients weighing up to 28 stones 177kg with no minimum working load limit and is suitable for the prevention and management of all grades of pressure ulcers Contra Indications e Integrity both in Alternating and Static Modes should not be used for patients with unstable spinal fractures In the case of patients with other unstable fractures where a moving surface can be harmful advice should be obtained from the appropriate physician before use e Integrity is designed as an aid to assist in the healing and prevention of pressure ulcers If there is no improvement in the patient s condition clinical
3. pump from the mains power supply before cleaning before cleaning Do not use phenol based solutions to clean the system Make sure the system is clean and dry prior to use or storage Never use sharp objects or electrically heated under blankets on or under the system Store the pump and mattress in the protective bag supplied Only the pump and mattress combination as supplied by Sumed should be used The correct function of the product cannot be guaranteed if any other Manufacturer s pump and mattress combination is used Maximum working load limit is 178kg 28 stones About this manual This manual is your introduction to Integrity Auto Adjusting Full Dynamic Replacement Mattress System Use this manual to initially set up the system and keep it as a reference for day to day routines and as a guide to maintenance Noise levels should be less than 30dB About Integrity Integrity is an Auto Adjusting Full Dynamic Replacement Mattress System to assist in the prevention treatment and management of pressure ulcers Integrity comprises a pump and mattress replacement system which can be used on standard hospital profiling auto regression and normal domestic beds with bed rails or sides Beds can be adjusted or profiled with the Integrity mattress in position Manufactured by Sumed International UK Ltd Integrity House Units 1 2 Graphite Way Hadfield Glossop Derbyshire SK13 10
4. 12 9 Technical Specifications Power Unit Specification Part number 12345P Input 220 240V AC 50Hz Power consumption 10W max Fuse rating TIAL 250V Weight 1 5kg approx Dimension L26cm x W8cm x H13cm UK and Euro Electrical Safety Standards Complies with EN 60601 1 1990 A13 1996 Degree of protection against electric shock Degree of protection against water ingress Class Type BF IPXO Mode of operation Integrity Specification Dimension Continuous L195 5cm x W86 4cm x 15cm approx Weight of air mattress within a bag Accessories Spare Parts 12kg approx Detachable mattress cover 2 way stretch cover Part No 12345C Alternating pressure mattress system complete Part No 12345 Alternating pressure mattress including tube but not the pump Part No 12345M Alternating pressure mattress system pump Part No 12345P Carry bag Part No 12345B Power lead Part No 12345PL Environmental Protection Please dispose of this unit in accordance with local regulations Retardancy Complies with BS7177 crib 5 BS597 1 BS597 2 In the event of a problem you must first contact your supplier The Manufacturer Sumed recommends that this product is serviced annually This product carries a Manufacturer s warranty period for the power unit and the air mattress of 2 years against manufacturing defects The Manufacturer s warranty will be invalidated if the
5. H Telephone 01457 890980 Fax 01457 890990 sales sumed co uk www sumed co uk SUMEC eoceanbee Contents 1 Usage and Controls of the Integrity Pump Page 4 5 2 Integrity Mattress Components Page 6 7 3 Clinical Applications Page 8 4 Installation and Set Up Page 8 5 Operation Page 9 6 Cleaning and Decontamination Page 10 7 Routine Maintenance Page 11 8 Troubleshooting Page 11 9 Technical Specifications Page 12 10 Warranty and Service Page 12 1 Usage and Controls of the Integrity Pump The controls and indicators are located on the top panel Comfort EMEF Lock unlock Alternating Mode Cyce minutes v Low Pressure alarm mmHg t Power Failure alarm ON Static Mode Auto Firm Mode Auto Dual Mode Nursing Standby The pump can be fixed to the foot end of a hospital bed by the bed brackets provided The pump can also be placed upright on the floor On Standby When the green indicator is on this means that the power unit will start to operate When the orange indicator is on this means that the unit is in Standby mode and will not operate This can only be used in Unlock mode Comfort Select the green indicators for a soft medium or firm setting The power unit automatically adjusts and shifts to the most appropriate pressure depending on the selected setting This function can be used only to adjust the Comfort level around the preset levels for S Soft M Medium a
6. advice should be sought The above are guidelines only and should not replace clinical judgement or professional experience 4 Installation and Set Up Integrity is supplied in its own carrying bag and comprises of the following Integrity pump Mains power cord Integrity mattress replacement system e Laminated quick set up guide Remove the existing mattress from the bed frame then follow the steps below Step 1 Check that there are no sharp objects on the bed frame surface that will come into contact with the mattress system The end with a connector for the power unit is the foot end Step 2 Ensure the mattress is positioned centrally on the bed ensuring there are no gaps that could cause entrapment Secure the mattress to the bed with the securing straps on to the fixed section of the bed however with a profiling bed the straps must be attached to the profiling sections Step 3 Place the pump in the preferred position Step 4 Connect the air hoses at the foot end of the mattress to the air outlet of the pump these only fit in one way Ensure CPR tag is in closed position Step 5 Connect the power lead to the pump Step 6 Plug the power cord of the pump into a socket with a power supply Step 7 Turn on the main power switch located at the side of the pump adjacent to the pipe inlets The orange indicator light will show indicating that the system is in Standby mode Press the On Standby button and the gre
7. air permeable and may present a suffocation risk It is the responsibility of the user to ensure that this product can be used safely e Electrical equipment may be hazardous if misused The pump should only be dismantled by authorised technical personnel Do not use the pump in the presence of flammable gases such as anaesthetic gas or in places exposed to water liquids oil smoke and flammable chemicals e Safety sides bed rails should be used at an appropriate height based on clinical assessment and in line with local hospital policy and or risk assessments e Ensure that there are no gaps wide enough to entrap a patient s head or body between the system and the bed frame Care should be exercised to prevent occurrence of gaps by compression or movement of the system as death or serious injury may occur Precautions For your own safety and the safety of the equipment always take the following precautions Apart from thin cover sheets placing extra layers between the patient and the system reduces the benefits provided by the system The mattress cover should not be pulled tight and covering sheets should fit loosely e It is advisable to avoid wearing clothing which may cause areas of localised high pressure due to creases seams or similar risks Keep the pump away from liquids Do not expose the system to naked flames or other heat sources Do not store the system in direct sunlight Disconnect the
8. en indicator light will show The pump will start pumping air after a few seconds Step 8 Wait until the inflation cycle has completed and the pump has stabilised to its default settings 10 minute cycles on a medium setting before placing the patient on the system This should take approximately 30 minutes Step 9 The unit AUTOMATICALLY adjusts for the weight of the user Then select the desired Comfort setting for the patient if required WARNING Make sure the mains power cord and air tubes are always positioned to avoid causing a hazard Make sure the mains power cord and air tubes are clear of any moving bed mechanisms or other possible entrapment areas 5 Operation These instructions cover day to day operation of the system Other operations such as maintenance and repair should only be carried out by suitably qualified personnel Deflating and storing the mattress 1 Switch off the pump and disconnect the pump from the mains power supply 2 Remove the tubes from the pump and mattress 3 If quick deflation is required the CPR tag can be used WARNING This CPR tag MUST be reconnected before resuming normal use 4 Make sure the mattress is clean and dry before rolling it up 5 Once deflated roll up the mattress starting at the head end 10 6 Cleaning and Decontamination WARNING Remove the electrical supply to the pump by disconnecting the mains power cord from the mains power supply before cleaning Pro
9. m of 10 minutes This data is based on the United Kingdom Health Service Guideline HSG 95 18 2 The top cover is then dried as follows e Covers can be tumble dried up to 85 C or air dried 7 Routine Maintenance Maintenance The equipment has been designed to be virtually maintenance free between service periods Service manuals Component parts lists and other information necessary for Integrity trained personnel to repair the system will be available from Sumed on request Service period It is recommended that the pump is serviced every 12 months by a Sumed authorised service agent Integrity pump General Care Maintenance and Inspection Check all electrical connections and the mains power cord for signs of excessive wear In the event of the pump being subjected to abnormal treatment e g immersed in water or dropped the unit must be returned to an authorised service centre Integrity mattress General Care Check for obvious signs of wear and tear or other damage If in doubt contact your supplier Serial number labels Pump The serial number label for the pump is on the back of the pump case Mattress The mattress is marked with a LOT number From this the Manufacturer can determine the date of manufacture 8 Troubleshooting In the event of malfunction contact your supplier if the following does not resolve your problem a Power unit does not operate Check if the two ends of the power cord are c
10. n the Auto Firm Nursing button is activated However after 30 minutes the unit will resume its previous setting in order to protect the patient from the risk of developing pressure ulcers This can be used in Lock or Unlock mode Auto Dual Mode This enables a combination of pressure therapy The function enables Alternating and Static Modes to alternate on one hour cycles The mattress automatically adjusts to the set comfort level Asan example if the Alternating Comfort setting is 27mmHsg this will adjust to a Static Mode setting of 18mmHg If the Alternating Comfort setting is 38mmHg this will adjust to a Static Mode setting of 24mmHg This can only be used in Unlock mode Low Pressure Alarm The alarm automatically sounds when a low air pressure is detected in the mattress The alarm can be muted by pressing the Low Pressure Alarm button In order to restore the audible alarm function you have to press the On Standby button and reset to a chosen setting This can only be used in Unlock mode Power Failure Alarm The alarm automatically sounds within 80 seconds when there is a loss of power during normal operation of the system e The indicators do not turn on during normal operation However when the orange indicators are on it means that either the Low Pressure Alarm or the Power Failure Alarm has sounded The alarm can be muted by pressing the Power Failure Alarm button Ifa prolonged power failure occurs refer to initial set up
11. nd F Firm In Alternating Mode Soft 20mmHg Medium 30mmHg and Firm 40mmHg The up and down arrow will allow for adjustment between 20 29 on the S setting 30 39 on the M setting and 40 49 on the F setting This adjustment can only be made in Unlock mode In Static Mode Soft 15mmHg Medium 20mmHg and Firm 25mmHg The up and down arrow will allow for adjustment between 15 19 on the S setting 20 24 on the M setting and 25 29 on the F setting This adjustment can only be made in Unlock mode Alternating Mode This feature allows the time cycle to be changed from its default cycle time of 10 minutes per cycle Options include 5 10 15 or 20 minutes per cycle The green light indicates which cycle time has been selected e This feature allows temporary relief of pressure in conjunction with the selected time cycle This in turn improves blood supply and assists in the healing and prevention of pressure ulcers This can only be used in Unlock mode Static Mode On this setting the system does not alternate If the green indicator is on this means that the Static Mode is activated After 1 hour Integrity automatically reverts to the last comfort and cycle time setting in Alternating Mode This can only be used in Unlock mode Auto Firm Nursing When carers are providing nursing care the mattress is pressurised to be flat and firm to provide a more stable surface to make nursing care easier When the green indicator is o
12. onnected and that the main power switch on the pump is on b Power unit is working but mattress is not inflating First check the CPR tag is in place and replace if appropriate Secondly check that the pipes are connected to the pump 11
13. tamper evident seal on the pump has been broken For after sales service maintenance and any questions regarding this or any other Sumed product please contact Sumed International UK Limited Integrity House Units 1 2 Graphite Way Hadfield Glossop Derbyshire SK13 10H Telephone 01457 890980 Fax 01457 890990 Website www sumed co uk E mail sales sumed co uk SUMEC eda h Alternating Pressure Mattress System User Manual INTEGRITY AUTO ADJUSTING FULL DYNAMIC REPLACEMENT MATTRESS SYSTEM Maximum Working Load Limit 178kg 28 stones Before connecting the pump to a mains socket carefully read all the installation instructions in Section 4 Page 8 Installation and Set Up Safety Criteria This product conforms with the requirements of EN60601 EN60601 1 EN 60601 1 2 Safety Warnings The product is only intended to be used as an aid to assist in healing and prevention of pressure ulcers and should be used in conjunction with a patient specific care plan The Manufacturer cannot be held responsible for inappropriate or incorrect use Do not tamper with the power unit e The power unit is not suitable for use in anaesthetic procedures involving inflammable gases Do not pull the CPR tag in normal working use except in an emergency situation Do not use sharp or pointed objects or subject the mattress to high temperatures e The cover of this product is vapour permeable but not
14. tective clothing should always be worn when carrying out decontamination procedures Avoid immersing electrical parts in water during the cleaning process Always refer to your Infection Control specialist for advice During use It is recommended that where practicable all parts of the system including mattress mattress top cover pump and tube set should be cleaned weekly Suggested cleaning materials Neutral detergents or neutral detergents combined with disinfectants e Alcohol disinfectant wipes Mild soap and water mattress assembly only Method 1 Dampen or rinse a clean cloth in the cleaning solution and remove excess fluid 2 Wipe all external cover surfaces clean Ensure they are dry before replacing the mattress in position For greasy or stubborn soiling use a non abrasive cloth 3 A clean cloth should be used with each application Each application of solution should be made in accordance with the Manufacturer s instructions Rinse after application with clean water using a clean cloth 4 If a combined detergent and disinfection solution is used rinse after application with clean water using a clean cloth 5 Allow the mattress to dry 6 Wipe all surfaces with an alcohol disinfectant wipe To launder the mattress top cover 1 To achieve thermal disinfection the temperature in the washing cycle of the laundering process must be maintained at 71 C for a minimum of 3 minutes or 65 C for a minimu
Download Pdf Manuals
Related Search