Pegasys to Horizon
Contents
1. 8 If further adjustment is required return to the Custom Job Settings menu steps 1 and 2 go to Edit and change the Gamma value to 1 3 Exit using Menu Test this new configuration and increase the gamma by 3 until the desired lightness is reached Gamma should not go above 2 0 if prints are still too dark at that gamma then there is another issue akon N Erica Sommer Page 5 4 10 2006 Codonics Inc Philips Medical Systems Pegasys to Codonics Horizon Imager Setup2. Erica Sommer Page 1 4 10 2006 Codonics Inc Philips Medical Systems Pegasys to Codonics Horizon Imager Setup If directly connected or on an isolated network choose an unused address that differs only in the last section octet For example if the IP address of the Pegasys is 192 9 200 10 the Horizon could use 192 9 200 50 as long as no other device on the isolated network is also assigned this IP NOTE Find the Pegasys IP address by going to System Maintenance gt System Utilities gt Unix Window and typing ypcat hosts Driver Version 5 only You will be limited to one grayscale media and one color media set through the front panel Default User Settings menu Go to Menu gt Default User Settings gt Media and select the media size and type combination for each of grayscale and color printing This setting can be changed at any time but in practice switching this setting often is awkward Install the imager s IP address Be aware that upon completion of this task the imager will reboot A Press and hold the left arrow button while pressing the Menu button Release both buttons B Press the down arrow J to the Network Settings menu and press Enter C Press the down arrow 4 to the Addresses menu and press Enter D Using the up and down arrows T J enter the first octet of the IP address Use the right arrow to move to the next octet and repeat the process Continue through the rest of the IP address If su
3. If more printers must be configured click Save and repeat this section DICOM Setup The DICOM setup must be peformed from the Master system EDITING THE HOST FILE 1 Click on Patient Utilities gt DICOM Utilities gt DICOM Configuration The window heading will be ADAC DICOM Configuration Select the Change Printer checkbox 3 Look for the Add Host button If the button is available enter the IP address assigned to the printer earlier in this instruction Use the hostname Horizon If there is already a Horizon imager set up either delete that entry or cancel the Add procedure Proceed to the section Printer Setup Utility 4 Ifthe Add Host button is not available do the following Erica Sommer Page 3 4 10 2006 Codonics Inc Philips Medical Systems Pegasys to Codonics Horizon Imager Setup Cancel the ADAC DICOM Configuration window Go to a UNIX shell System Maintenance gt System Utilities gt Unix Window Enter as superuser login su password adacsu owp D Change directories cd etc more hosts E Verify that no Horizon entry is present If there is an entry for Horizon note the IP address and the hostname exactly as written including case F Ifthe more utlility is still active exit it by typing q G Inthe Unix window type textedit hosts H At the bottom of the resulting window make a printer entry in the format IP address lt tab gt hostname Example 192 9 200 51 Horizon Click left on File to sav
4. for color printing is Codonics exclusive Medical Color Matching MCM setting The setting devised for Horizon is MCM 103 Gamma Affects the overall lightness or darkness of the printed image while preserving full black and full white An increase in gamma value will lighten the printed image a decrease in gamma value will darken the printed image Contrast Enhances or reduces the contrast of the printed image Positive settings will enhance contrast while negative settings will reduce contrast in the printed image Saturation Color prints only As saturation increases colors get brighter and more vibrant Negative saturation desaturation removes color and makes them more muted An example of the Configuration Info line using three settings is mcem 103 gamma 1 2 contrast 5 Codonics Driver printing only If the print is too dark and changes to settings do not seem to have any effect create a special Custom Job Setting for the printer Go to the printer and press the left arrow and the Menu key Menu Press the down arrow to Custom Job Settings then press Enter Go to New and press Enter Go to Name and press Enter Press the left and right arrows gt simultaneously Enter the name RAW_Js by using the up and down arrows Press Enter when this is complete Next go to the LUT setting and press Enter Change the LUT to visual Press Enter then Menu then send a print from the Pegasys to verify the change
5. Document One technique that can make printing easier for users is to create multiple printer entries based on the media size and type Therefore there will be one printer configuration for film one for color paper and one for grayscale paper To add a Codonics printer entry 1 Right click to PATIENT UTILITIES gt CODONICS UTILITIES gt CODONICS CONFIGURATION 2 Click on the Add button under the Codonics Printers list A highlighted unTitled entry appears in the list 3 Click on unTitled in the Printer Name field and type the name of a new configuration This name is used to identify the printer The configuration name should not contain any spaces or tabs for example CODONICS_ EP Use something descriptive particularly if multiple printer configurations will be used NOTE Do not use a configuration name that is a subset of another configuration name For example do not assign two configurations with the names CODONICS and CODONICS_HZ 4 Click on the down arrow next to the Printer Host Name field and select the correct hostname for the printer 5 Fill in Configuration Info with the following MCM 103 6 Fill in the remaining fields Pay attention to the media size and type use 8x10 for small film A for American Letter and A4 for European Letter Make sure that color or grayscale option is set correctly as well as the medium type Film or Paper 7 If all printers have been configured click Save All amp Exit
6. Erica Sommer Page 4 4 10 2006 Codonics Inc Philips Medical Systems Pegasys to Codonics Horizon Imager Setup If images are not being received by the printer but the ping command comes back successfully restart the Codonics Print daemon right click on the desktop to display the Pegasys Main Menu and then right click PATIENT UTILITIES gt CODONICS UTILITIES gt RESTART CODONICS PRINT DAEMON Setting the Horizon as the Default Printer See also the section Setting the Codonics Printer as the Default in the Codonics Color Dye Sublimation Printers Ver 7 0 Release Document To set the Horizon as the default for all sessions use the Set Default Devices application Click on SYSTEM MAINTENANCE gt SET DEFAULT DEVICES gt CHANGE DEFAULT SETTINGS gt CHANGE DEFAULT FORMATTER To change the default printer for a single session 1 Display the Formatting Control Panel by right clicking on the Format icon and selecting Control Panel from the pop up menu 2 Right click on the Formatter button and selecting a Codonics printer from the pop up menu Click Proceed 3 When the application is closed the default printer will revert to the printer set through Set Default Devices or through the Print Preview Adjusting Image Quality The Horizon provides a number of adjustments that can be used to optimize printed image quality These adjustments are invoked using the Configuration Info field in the Configuration screen The most important setting
7. Philips Pegasys to Codonics Horizon Quick Start Guide Overview The purpose of this instruction is to outline the essential steps required to set up and configure a Codonics Horizon printer for operation with a Philips Pegasys workstation More detail can be found in other supplied documents such as the Horizon User s Manual Horizon Technical Manual and Codonics Color Dye Sublimation Printers Ver 7 0 Release Document In addition this document attempts to outline some of the unsupported combinations such as the driver version 5 with their capabilities and drawbacks To navigate the Pegasys desktop it is necessary to right click on the background and hold to bring up menu options such as System Maintenance There are two ways to connect a Horizon to Pegasys 1 Driver A Use version 7 of the Codonics print driver B Version 7 driver requires version 5 of the Pegasys system software C The driver supports A A4 and 8x10 page sizes Use DICOM instead of the driver if large medias need to be supported D Version 5 of the driver may be used but only in a limited capacity the media must be chosen from the printer s front panel so that only one color media and one grayscale media may be selected at a time This combination is not officially supported E PegX systems Pegasys version 3 4 cannot be upgraded to version 5 of the Pegasys system software F The Horizon must have an EP Emulation key installed If this feature is enabl
8. bnet and gateway information are required use the right arrow gt to move to the Subnet line and install the subnet address using the same procedure as the IP Use the right arrow to continue to the Gateway address F When all addresses are complete press Enter then press Menu This step will initiate an imager reboot This process takes about 5 minutes NOTE If the subnet or gateway information is illegal based on the IP address the printer will delete these settings and return to the default subnet and gateway upon reboot Run an Imager Status Test Print A Ensure that the red Alert light is not on If it is follow the prompts on the bottom half of the screen to resolve the condition For instance ensure that the receive trays are inserted properly and that at least one media is installed in the imager TIP Use one of 8x10 film A or A4 size DV Paper if available for this test Press Online Press the Down Arrow 4 to Test Prints and press Online Select the currently loaded media size and type Press Enter Select Imager Status from the menu and press Enter Leave the Copies default set to 1 and press Enter This step will initiate the teste print Check the resulting printout for the IP address and for the correct PostScript and DICOM options 1 NetworkInfo IP Address Subnet Mask and Gateway 2 PrinterFeaturelnfo DICOM will be the top two options listed in this section EP Emulation will also be listed here m onmgp
9. e the change To make the change recognized by the system type cd var yp make J Finally return to the ADAC DICOM Configuration utility to finish the installation PRINTER SETUP UTILITY The ADAC DICOM Configuration is very similar to the Codonics driver setup screen One key difference is the AE title Choose the appropriate AE title from the following list Media Type AET to use 14x17 DV Film Blue Base 14x17 dvfb 14x17 DV Film Clear Base 14x17 dvfc 8x10 DV Film Blue Base 8x10 dvfb 8x10 DV Film Clear Base 8x10 dvfc 14x17 DV Paper grayscale 14x17 dv A Size DV Paper grayscale a dvp A4 Size DV Paper grayscale a4 dv A Size CV Paper color a cvp A4 Size CV Paper color a4 cvp Bracketing Print various contrasts gammas SpecialBracket See Page C 2 of the Horizon User s Manual for a complete list of pre set AE titles The DICOM interface supports 8x10 11x14 and 14x17 media sizes The DICOM interface does not include A or A4 page sizes Use the correct AE title from the above list select 8x10 for the page size and make sure that a magnification type such at Bilinear is also set These three settings will force the print onto letter sized paper and will ensure the best fit for letter sized prints Select the preferred layout 1x1 or 2x2 Under Configuration Info enter mcm 103 After all settings have been changed select Save and Exit Re enter this screen to set up subsequent printers Restarting the Codonics Print Daemon
10. ed it will be reflected on the Imager Status Test Print 2 DICOM A Use Pegasys DICOM versions 4 24 and 4 25 There are known issues with 4 22 B Pegasys DICOM 4 24 and 4 25 require Pegsasys system software version 5 C PegX cannot be upgraded to DICOM 4 24 or 4 25 but it can use 4 22 D Large and small formats are supported E Limited print layouts 1x1 and 2x2 are supported in the Pegasys DICOM interface F The Horizon must have the DICOM feature installed Philips Horizon SF configurations do not have this option by default and it must be purchased See the System Requirements section of the Codonics Color Dye Sublimation Printers Ver 7 0 Release Document for details on the offically supported configurations The Add Del Utility must be performed on the Pegasys Master system Please refer to the documentation shipped with the Horizon for unpacking and media loading details These instructions begin with a printer which has been powered up and cleaned Horizon Setup 1 Insert the correct Cat 5 network cable on the back of the printer Use the straight through cable blue cable provided by Codonics if the Horizon and the Pegasys are part of a larger network Use the crossover cable gray cable provided by Codonics if the Horizon will be connected directly to the Pegasys 2 Determine the IP address to be used by the Pegasys Ona large network obtain network address information from the site s System Administrator
11. ow Driver based Setup ADDING THE HORIZON TO THE PEGASYS Before configuring a Codonics printer in the Pegasys software you must add the printer to the Pegasys master host file using the ADD DEL PRINTER utility See also the section Adding or Deleting Codonics Printers in the Codonics Color Dye Sublimation Printers Ver 7 0 Release Document 1 Right click on the background to PATIENT UTILITIES gt CODONICS UTILITIES gt ADD DEL PRINTER A UNIX window appears To exit the Add Del utility prior to completing a task press lt CTRL C gt 2 Log in as Superuser login name adac password adacsu 3 Type Erica Sommer Page 2 4 10 2006 Codonics Inc Philips Medical Systems Pegasys to Codonics Horizon Imager Setup Add lt enter gt 4 Follow the prompts Use the IP address set in the preceding section as the IP address of the printer Please note that two hostnames cannot point to the same IP address if there is already an entry for the IP that you are configuring either cancel the Add procedure or delete the old entry 5 Verify the connection by going to a shell window and typing ping printer ip PRINTER CONFIGURATION IN PEGASYS This section configures the options like the media size and type MCM and formats Multiple configurations can be created for a single printer in order to have different sets of preferences See also the section Adding a Codonics Printer Entry in the Codonics Color Dye Sublimation Printers Ver 7 0 Release
Download Pdf Manuals
Related Search