Home

User Guide - VOXX International Corporation

1. among the following options i If the chosen storage location is empty denoted by or if the storage location contains the FM preset currently being used denoted by current then the FM channel tuning screen is displayed ii If the chosen storage location has an FM preset that is not currently being used and you want to edit it Edit Channel is highlighted Press the Select button The FM channel tuning screen is displayed iii If the chosen storage location has an FM preset that is not currently being used and you want to start using it press 4 to highlight Start Using and press the Select button Skip to step 7 Press and P to tune the desired FM channel in steps of 2 i e 99 3 to 99 5 Press V and 4 to tune the desired channel in steps of 1 i e 99 3 to 100 3 Press the Select button Mir Mi to select the FM channel Edit FM Channel 2 99 3 FM If you are editing the storage Press arrow keys to tune location that has the current and Select to confirm FM preset skip to step 7 Otherwise Start Using will be highlighted Press the Select button NOTE You can also preset an FM channel in a storage location without having to start using it right away Just press menu and exit the screen Configuring Your onyX The chosen FM channel will be confirmed on the display screen and the onyX will tune to that FM channel Set your vehicle s FM radio to same FM channel
2. display screen that denotes antenna signal strength You can also press menu and then press W to scroll to and highlight Signal Indicator Press the Select button The Satellite and Terrestrial bars show the strength of the signal being received If the signal reception is good press and hold menu to return to the main display screen Signal Indicator 7 Ensure onyX is tuned to channel 1 Upon power up onyX should tune to channel 1 by default when it s not yet activated If it s not on channel 1 refer to Listening to Satellite Radio on page 55 to learn about how to tune a channel 8 Turn on your vehicle s stereo system Set it to play input from the auxiliary input source 9 You should hear XM channel 1 through your vehicle s stereo system You are now ready to activate your onyX 10 The audio level output of the onyX can be increased or decreased as necessary to match the audio levels of other sources in your vehicle Refer to Set Audio Level on page 89 If the signal reception is good but there is no audio when tuned to channel 1 be sure the vehicle s stereo system is set to the correct source i e auxiliary input source step 8 Also be sure that the audio level is set high enough to be heard step 10 Refer to Troubleshooting on page 102 for additional help Option 2 Cassette Adapter Installation Instructions 1 Plug the Cassette Adapte
3. XM onyx User Guide omi j 26 l gt Pulse Ga Maroon 5 A gt Makes Me Wonder 07 y v SIRIUS omy SATEL Li Table of Contents Introduction o oo oooo A en een 6 Safety and Care Information 7 What s in the Box o oooooo m o 9 OMY X FUNCTIONS su ee 10 PowerConnect Vehicle Dock 11 Vehicle Installation 13 Step 1 Choose a Location for Your Radio ma a aia 14 Step 2 Install the Dash or Vent Mount 16 Step 3 Mount the Magnetic Mount Antenas use 20 Step 4 Route the Magnetic Mount Antenna Cable Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter 0 000 37 Step 6 Connect the Audio 38 Activation ooo o 49 Using Your onyX 51 The Main Display 52 Navigation Basics 53 Listening to Satellite Radio 55 FM Presets oia 60 Special Features 63 Color THEMES 00 Trim Rings Parental Controls 68 Where Else Can You Use Your ONYX cece ewww eens 75 Configuring Your onyX 77 Radio ID au uuu au ir pee eee 78 Find Available FM Channels in Your Area TA 79 Set and Select an FM Channel 82 Jump Settings 04 000000 86 Set BrightnesS o ooooooooo 88 Set Audio Level ooo ooo 89 Signal Indicato isis stepis tiens assor 90 Factory Settings u
4. e The information may not be available or updates may be in progress Traffic and Weather channels sound different from other channels e These channels use a different audio technology than other channels so they often sound different from other channels The demo is playing e Your Magnetic Mount Antenna is not connected or you are not receiving the signal Check that the antenna is connected properly and is not obstructed e Press and hold the Select button for 10 seconds to exit Demo Mode e You can disable Demo Mode Refer to Demo Mode on page 94 106 107 Product Specifications System Power Requirements Operating Temperature Audio Output onyX Radio Dimensions Weight PowerConnect Vehicle Dock Dimensions Weight FM Connector Audio Connector Antenna Connector Power Connector PowerConnect Power Adapter Dimensions Weight Input Output Cable Length Vehicle Antenna Type Connector Cable Length Aux In Cable Connectors Cable Length 9 16 V DC 500 mA max 20 C to 60 C 4 F to 140 F 1 0 Vrms max 115 mm width x 61 mm height x 17 mm depth 4 5 in width x 2 4 in height x 0 7 in depth 95 g 3 4 0z 102 mm width x 59 mm height x 31 mm depth 4 0 in width x 2 3 in height x 1 2 in depth 46 g 1 6 oz 2 5 mm female 3 5 mm female SMB male 4 8 mm female 94 mm width x 43 mm height x 34 mm depth 3 7 in
5. Pressing menu displays various options to make setup and feature changes Pressing menu when in menu options returns to the previous menu option screen until menu options is exited Pressing and holding menu returns to the main display screen in most instances FM Button FM Provides easy tuning of FM presets for optimized PowerConnect performance Repeatedly pressing FM displays and cycles through the list of preset FM channels one at a time The radio automatically tunes to the displayed FM channel Pressing and holding FM accesses the FM Settings menu It is not available when Aux In Cable or Cassette Adapter is used for audio connection Jump Button Depending on how it is configured pressing jump either tunes to the channel broadcasting traffic and weather conditions of a selected city from a list of the 20 most congested cities or tunes to the previous channel that was being played Direct Button direct Pressing direct prompts for the entry of a channel number using the number buttons Once the channel number is entered the radio directly tunes to the new channel Number Buttons BI gt gt gt ee Each number button stores a favorite channel in its button location and provides one touch access to it afterward Number buttons also directly tune to a channel when the channel number is entered after pressing direct Listening to Satellite Radio Tune a channel 1 Press and r
6. between the choices 4 Ifyou have selected Last Channel press and hold menu to return to the main display screen If you have selected Traffic Weather continue with step 5 5 Press to scroll to and highlight Set Location and press the Select button 6 A list of cities will be displayed Press W to scroll to and highlight your desired location and press the Select button 7 The JUMP Settings screen will display the location you selected Press and hold menu to return to the main display screen Set Location f JUMP Settings Atlanta Mode Traffic Weather O Baltimore Set Location ATL Boston Chicago O Dallas Configuring Your onyX Set Brightness To change the display s brightness 1 Press menu 2 Press to scroll to and highlight Brightness and press the Select button 3 Press 4 to decrease or P to increase the brightness of the display 4 Press the Select button to confirm the brightness setting Press arrow keys to adjust 5 Press and hold menu to return to the and Select to confirm main display screen Set Audio Level The audio level of the onyX can be adjusted when an audio connection is made between the dock and the vehicle s stereo system Audio level is used to adjust the onyX s volume level to match the volume of other audio sources you may use such as aCD player other FM stations or an MP3 player Do not use the audio level as a vol
7. e If the message persists most likely the Magnetic Mount Antenna cable has been damaged Replace the antenna If you see this on the screen Channel Off Air Try this e The channel you ve selected is not currently broadcasting Tune to another channel Loading e Your onyX is acquiring audio or program information This message usually goes away in a few seconds Updating e Your onyX is updating with the latest encryption code Wait until the update is done e You may be trying to tune to a channel that is blocked or unavailable Tune to another channel If this happens You do not receive all the channels to which you subscribed No program information such as artist name song title or channel exists Try this e Ensure that you have activated your service by following the steps in Activation on page 50 e Go to www xmradio com refresh and follow the directions refresh your radio e Call 1 800 967 2346 for further assistance Audio sounds too soft e Raise the volume of your stereo system or increase the audio level of your onyX until the sound quality improves Refer to Set Audio Level on page 89 Troubleshooting If this happens No audio when using the Aux In Cable or Cassette Adapter Try this e Check all cables between your onyX and your vehicle s stereo system for a firm and secure connection Ensure you have selected the proper input sourc
8. ss su 00 9 Demo Mode ee ee eee eee 94 Using the Vehicle Dock From the Universal Xpress Car Kit 96 Turn FM Transmitter On Off 98 Troubleshooting 101 Product Specifications 107 Patent Information 109 Environmental Information 109 Owners Record aise o disse te iras ico 112 Introduction Features Congratulations on your purchase of the onyX The onyX has these exciting features to enhance your overall experience e Large color display View artist name song title and channel information on a color display Customize your display Choose the backlight color theme that matches your mood or your vehicle dash lights Personalize your radio Choose the trim ring that reflects your taste or complements your vehicle interior Improved audio connection options Use either the included Aux In Cable or the new PowerConnect technology to receive audio through your vehicle s stereo system Enhanced real time channel guide Browse programs artists and songs playing on other channels without having to change the channel you are on Favorite channel presets Save and enjoy fast access to up to 10 of your favorite channels FM preset button Store and quickly access FM channels that give you the best audio reception when using PowerConnect One Touch Jump Directly access traffic or weather of the 20 most congested cities or use it
9. PUSH aman Foot y Dash Vent Louver Dash 3 Push the Vent Mount onto the vehicle vent as shown 1 until it HOOKED Vent TILT ADJ USTMENT HOLES Dash Vent To remove the Vent Mount push the mount into the vent Then lift up until disengaged from the rear of the vent louver and remove the Vent Mount Vehicle Installation Step 3 Mount the Magnetic Mount Antenna The Magnetic Mount Antenna contains a strong magnet which will stick to any metal part of your vehicle but will not damage the vehicle To install the Magnetic Mount Antenna a 1 Choose the best location for your antenna considering your vehicle type Pay particular attention to any Y accessories that you may have like luggage racks and how frequently you may use them Magnet Sedan Coupe We recommend mounting the antenna just above either the front windshield or the back window as shown SUV We recommend mounting the antenna at the rear of the roof as shown Convertible We recommend mounting the antenna at the leading edge of the trunk as shown Pickup Truck We recommend mounting the antenna just above the front windshield as shown 2 Clean the surface of the selected mounting location using the alcohol preparation pad and let it dry thoroughly Vehicle Installation 3 Place the antenna in the location you selected Follow the Tips and Caut
10. be increased or decreased as necessary to match the audio levels of other sources in your vehicle Refer to Set Audio Level on page 89 If the signal reception is good but there is no audio when tuned to channel 1 be sure the vehicle s stereo system is set to the correct source i e cassette source step 8 Also be sure that the audio level is set high enough to be heard step 10 Refer to Troubleshooting on page 102 for additional help Option 3 PowerConnect Installation Instructions 1 Insert the dock into the MA mount Insert your onyX into the J dock Power on your onyX 1 A by pressing the Power i E button Be sure the vehicle is outside and the antenna has a clear view of the sky Verify that you are receiving the XM signal There should at least be one bar on the lower left corner of the main display screen that denotes antenna signal strength You can also press menu and then press Y to scroll to and highlight Signal Indicator Press the Select button The Satellite and Terrestrial bars show the strength of the signal being received If the signal reception is good press and hold menu to return to the main display screen You are ready to make the audio connection Vehicle Installation 5 You ll first need to find an available FM channel An available FM channel is one that s not being used by an FM radio station in your area When you tune your FM
11. dash method using the Dash Mount and B is the vent clip method using the Vent Mount Option 1 Option 2 DER E A 5 SY gt CAES Y ASS a Vehicle Installation Step 2 Install the Dash or Vent Mount Depending on your situation you can either choose to use the Dash Mount or the Vent Mount IMPORTANT When you install the chosen mount do not attach the dock to the 5 mount All cables should be attached to the dock prior to connecting the dock to the mount Installing the Dash Mount Eu CAUTION The adhesive used on the Dash Mount may be difficult to remove Do not install this mount on leather surfaces contact your vehicle dealer if you are unsure about your dash surface and make sure the air temperature is at least 60 F 15 C during installation If it s not at least 60 F turn on the heater in your vehicle to bring the temperature up to 60 F 1 Locate a flat surface for the Dash Mount Make sure there is ample room for the PowerConnect Vehicle Dock and onyX Radio when installed 2 Set the orientation of the Dash Mount before adhering it Loosen the knob and adjust the adhesive foot for the location you selected in Step 1 Choose a Location for Your Radio on page 14 e Option 1 amp Option 3 should be oriented asl e Option 2 should be oriented as II 3 The dock mounting plate can be t
12. onyX will tune to the FM channel 9 You should hear XM channel 1 through your vehicle s FM radio If you are satisfied with the sound quality you re done You are now Set your vehicle radio to the ready to activate your onyX above channel to enable audio 10 If the selected FM channel doesn t work well for you work down the list of FM channels until you find one that allows you to hear XM clearly Each time you will need to tune your vehicle s FM radio to the FM channel and then set your onyX to transmit on the same FM channel steps 7 amp 8 If the signal reception is good but there is no XM audio when tuned to channel 1 verify that both the onyX and your vehicle s FM radio are tuned to the same FM channel steps 7 amp 8 Also ensure the chosen FM channel is a suitable one to use in your area step 5 Verify that nothing is plugged into the AUDIO connector on the PowerConnect Vehicle Dock Refer to Troubleshooting on page 102 for additional help Option 4 FM Direct Adapter FMDA Installation The FMDA needs to be installed by a professional installer Professional installation can help improve your radio s reception and significantly reduce the visibility of wires To learn more check with the retailer where you bought your radio or go to xmradio com accessories 48 49 Activation Before you can enjoy Commercial Free Music plus Sports News Talk amp
13. player Cassette Adapters are sold separately and can be purchased from an electronics retailer or go to xmradio com accessories e Option 3 Good Use the PowerConnect feature in the onyX PowerConnect plays the audio through your vehicle s FM radio e Option 4 Best Use the FM Direct Adapter If none of the previous three audio connection options will work in your vehicle then you will need to use the FM Direct Adapter FMDA sold separately The FMDA needs to be installed by a professional installer and directly connects the onyX to your vehicle s FM radio To learn more check with the retailer where you bought your radio or go to xmradio com accessories Follow the installation instructions in the next several sections for the audio connection option that you have selected Option 1 Aux In Cable Installation Instructions 1 Plug one end of the Aux In Cable into the green AUDIO connector on the dock ago CDs RO RUXINAODE fe N Plug the other end into the auxiliary input jack connection of your vehicle s stereo system Insert the dock into the mount i Power on your onyX by pressing the Power button Insert your onyX into the dock Be sure the vehicle is outside and the antenna has a clear view of the sky Verify that you are receiving the XM signal There should at least be one bar on the lower left corner of the main Vehicle Installation
14. width x 1 7 in height x 1 3 in depth 69 g 2 4 oz 916VDC 5VDC 1 5A 1 4 m 4 ft 7 in XM Magnetic Mount SMB female right angle 7 0 m 23 ft 3 5 mm stereo male to 3 5 mm stereo male 1 2 m 4 ft Patent and Environmental Information Patent Information It is prohibited to and you agree that you will not copy decompile disassemble reverse engineer hack manipulate or otherwise access and or make available any technology incorporated in this product Furthermore the AMBE voice compression software included in this product is protected by intellectual property rights including patent rights copyrights and trade secrets of Digital Voice Systems Inc The software is licensed solely for use within this product The music talk news entertainment data and other content on the Services are protected by copyright and other intellectual property laws and all ownership rights remain with the respective content and data service providers You are prohibited from any export of the content and or data or derivative thereof except in compliance with applicable export laws rules and regulations The user of this or any other software contained in a SIRIUS XM radio is explicitly prohibited from attempting to copy decompile reverse engineer hack manipulate or disassemble the object code or in any other way convert the object code into human readable form Environmental Information Follow local guidelines f
15. Entertainment you need to activate your onyX 1 Make sure your onyX is properly installed turned on and receiving the XM signal so that you can hear the audio on channel 1 2 Make a note of your XM Radio ID You can find it on channel O on a label on the bottom of the gift box and on the label on the back of your onyX G NOTE The XM Radio ID does not use the letters I O S or F 3 Activate your service e Online Go to www xmradio com and click on ACTIVATE RADIO in the top right corner OR By phone Call 1 800 XM RADIO 1 800 967 2346 Eu TIP You can follow the built in activation wizard in your Fi ex S ens will hel D onyX If your radio has not been activated press menu led and the first item in the list will be Activate Radio Press red ep Sieou with the activation of your radio Welcome the Select button A series of screens will guide you or press menu to cancel through the activation process Follow the instructions on ADS each screen Press the Select button to advance to the Press Select to continue next screen or menu to cancel and return to the main display screen 4 When your service is activated your onyX will receive all channels to which you have subscribed At this time if you press 4 or Y you can scroll and tune other channels Activation usually takes 10 to 15 minutes but may take up to an hour We recommend that your radio remain on until activated 51 Using Your onyX Th
16. IMPORTANT You ll first need to find a f suitable FM channel that is unused or Set your vehicle radio to the available in your area above channel to enable audio 99 3 FM To quickly select an FM channel from the preset list 1 Press FM to display the current FM preset 99 3 FM 2 To display and select the next FM preset press FM The radio p will tune to the displayed FM Set your vehicle radio to De channel If the preset is the one above channel to enable audio you want press menu or wait for the screen to timeout 3 Repeatedly pressing FM will cycle through the FM presets 4 Set your vehicle s FM radio to same FM channel 103 7 FM Set your vehicle radio to the above channel to enable audio Configuring Your onyX Jump Settings The jump button can be configured to either jump to the traffic and weather channel of one of the 20 most congested cities or to jump back to the last channel to which you were listening When configured for traffic weather you ll need to select a desired city from the list To configure jump 1 Press menu 2 Press V to scroll to and highlight JUMP Settings JUMP Settings and press the Select 5 button Mode Traffic Weather 3 Mode will be highlighted with either RIAR ELI SgS Last Channel or Traffic Weather If you want to change the mode press the Select button Otherwise just leave it as shown Repeatedly pressing the Select button toggles
17. Select button Continue with step 3 e If you had previously selected a 4 digit code you will be prompted to enter your code i For each digit press one of Press OK to confirm Code Confirmation Your Parental Code is the O 9 keys and then press 3287 to advance to the next You will need this code to change digit Press dif you need or turn off Parental Controls to go back and edit a previous digit Press Select to continue ii When you have selected all 4 digits of the code press Special Features the Select button 3 At the Parental Controls screen Parental Controls will be highlighted Press the Select button to turn parental control On or press the Select button to turn parental control Off 4 Press and hold menu to return to the main display screen To lock or unlock channels or categories 1 Press menu 2 Press W to scroll to and highlight Parental Controls Press the Select button 3 You will be prompted to enter the 4 digit code For each digit press one of the O 9 keys and then press to advance to the next digit Press if you need to go back and edit a previous digit 4 When you have entered all 4 digits of the code press the Select button 5 If Parental Controls is shown as Off press the Select button to turn it On otherwise continue with the next step 6 At the Parental Controls screen Press W to scroll to and highlight Locked Channels Press the Select bu
18. ar Kit and plan to use SureConnect or FMDA as the audio connection option You ll have to turn On the FM Transmitter under the FM Settings menu However before you can access the FM Settings menu you first need to disable AUX Detect Refer to AUX Detect on page 91 Once you have disabled AUX Detect the FM Settings menu will be accessible To turn the FM Transmitter On 1 Press menu FM Settings 2 Press W to scroll to and highlight FM Settings and press the Select FM Transmitter button FM Channels 3 FM Transmitter will be highlighted Press the Select button to toggle the setting from Off to On 4 The FM Channels menu item will now be accessible allowing you to tune the onyX and the FM radio in your vehicle to the same FM channel O TIP onyX is programmed with FM channel 97 9 as the default setting To turn the FM Transmitter Off If you are using the older model Vehicle Dock from the Universal Xpress Car Kit and plan to use the Aux In Cable or a Cassette Adapter as the audio connection option you ll have to turn the FM Transmitter under the FM Settings menu in the onyX Radio Off if it was previously turned On 1 Press menu 2 Press Y to scroll to and highlight FM Settings and press the Select button 3 FM Transmitter will be highlighted Press the Select button to toggle the setting from On to Off 4 A warning message will be displayed advising you to connect th
19. dentifications are the intellectual property of NBA Properties Inc and the respective NBA member teams 2009 NBA Properties Inc 2009 NFL Properties LLC All NFL related trademarks are trademarks of the National Football League NHL and the NHL Shield are registered trademarks of the National Hockey League NHL 2009 All NHL logos and marks and NHL team logos and marks depicted herein are the property of the NHL and the respective teams and may not be reproduced without the prior written consent of NHL Enterprises L P The Home Ice channel is a registered trademark of XM Satellite Radio Inc The Swinger Golfer logo is a registered trademark of PGA TOUR Inc Visit xmradio com xmlineup for updates All programming channel lineup XM service subject to change or preemption All other marks and logos are the property of their respective owners All rights reserved Hardware subscription and activation fee required Other fees and taxes may apply Month to month subscriptions must be activated via telephone Hardware and subscription sold separately Subscription governed by XM Customer Agreement which can be found at xmradio com serviceterms Prices and programming are subject to change XM Radio U S service only available in the 48 contiguous United States and the District of Columbia Owners Record Owner s Record The radio model number is located below and the XM Radio ID is located on the label on the back of the onyX Rec
20. detects it s not connected to the antenna or the antenna stops receiving a signal It disappears when the antenna is connected properly or when the radio starts receiving a signal You can also exit demo mode at any time by pressing and holding the Select button for 10 seconds If desired you can also manually put the onyX in demo mode The ability for onyX to enter demo mode is enabled by default If you don t want onyX to ever enter the demo mode you can disable the demo feature You can enable it again at another time if desired To enable or disable the demo mode 1 Press menu Demo Mode 2 Press Y to scroll to and highlight Demo Mode and press the Select Status button Enter Demo Mode 3 Status will be highlighted Press the Select button to toggle the setting between enabled or disabled Repeatedly pressing the Select button toggles between the choices enabled 4 Ifyou have selected disabled press and hold menu to return to the main display screen If you have selected enabled continue with step 5 Press Y to scroll to and highlight Enter Demo Mode and press the Select button The demo mode will start in 10 seconds 6 To exit demo mode at any time press and hold the Select button for 10 seconds Demo Mode Entering Demo Mode Press Hold Select for 10 seconds to exit Configuring Your onyX Using the Vehicle Dock From the Universal Xpress Car Kit If you have chosen to use the Vehic
21. e on your vehicle s stereo system e If you are using the Vehicle Dock that came with the Universal Xpress Car Kit ensure that the FM Transmitter in the onyX is turned Off and increase the audio level of the onyX Refer to Set Audio Level on page 89 Audio fades or has static when listening e Check all cables for a firm and secure connection If you are using PowerConnect to listen via your vehicle s FM radio and the problem persists it most likely is interference from another commercial or broadcast FM station You will need to find an unused or available FM channel in your area Refer to Find Available FM Channels in Your Area on page 79 If you are using PowerConnect and you cannot solve the audio problem try connecting the audio using the Aux In Cable or a Cassette Adapter Refer to page 39 and page 41 If you cannot use those solutions consider using an FM Direct Adapter Refer to page 47 If this happens No audio when using PowerConnect or FMDA Try this e Check that your onyX and your vehicle s FM radio are tuned to the same FM channel e For PowerConnect ensure you are using the PowerConnect Vehicle Dock and PowerConnect Power Adapter e If you are using the Vehicle Dock that came with the Universal Xpress Car Kit ensure that the FM Transmitter in the onyX is turned On Refer to Turn FM Transmitter On Off on page 98 No song title or artist name is displayed
22. e Aux In Cable Press the Select button to confirm that you want to turn off the FM Transmitter 5 Press and hold menu to exit FM Settings FM Transmitter off Turn OFF FM Please connect an AUX cable or no audio will be available Press Select to confirm 100 Trouble 101 Troubleshooting onyX has been designed and built to be trouble free but if you experience a problem try this e Check that all connections are firm and secure e Make sure the vehicle power socket is clean and free of corrosion e Make sure you have connected the onyX as described in this User Guide Verify that the PowerConnect Power Adapter is plugged into the vehicle s cigarette lighter or power adapter socket and that the LED on the PowerConnect Power Adapter is lit on If not your vehicle may need to be running to provide power to the socket If you see this on the screen Try this Acquiring Signal Make sure that the vehicle is outdoors with a clear view of the sky Make sure the Magnetic Mount Antenna is mounted outside of the vehicle Move the antenna away from any obstructed area For example if you are parked in an underground garage you should receive a signal after leaving the garage Check Antenna Connection Make sure that the antenna cable is firmly and securely plugged into the PowerConnect Vehicle Dock Make sure the cable is not bent or broken e Turn onyX Off then On to reset this message
23. e Main Display When listening to a channel information about the channel is displayed Channel Number YA IA Channel Name STUER Mat a alanis Artist Name Bullet With Butterfly Wings Gaeta a Antenna Signal Song Title Strength or Talk Show Schedule or Game Time Game Details Navigation Basics Power Button Pressing the Power button turns the onyX On or Off GAR Navigation Buttons O Qu Use the Left Right Up and Down buttons to navigate through various features and functions of onyX e Left d or Right P button Displays the channel categories such as Rock Pop Sports Talk New etc Repeated presses cycle through the categories one at a time Decreases or increases the settings of various menu options such as Brightness Audio Level etc e Up amp or Down Y button press and release Immediately tunes to the next or previous channel in the channel lineup Scrolls through lists and highlights an item in the list e Up 4 or Down Y button press and hold Continuously scrolls through any list While on the main display screen continuously scrolls through the channel lineup and briefly displays the information of each channel When the button is released radio tunes to the last channel it had scrolled to in the channel lineup lt gt Select Button O The Select button selects a highlighted item in a list and confirms gt settings Using Your onyX Menu Button menu
24. e first FM channel on your Channel Finder list and tune the FM radio to that channel If you do not hear a local FM station broadcast then tune the onyX to the same FM channel Refer to Set and Select an FM Channel on page 82 You should hear the XM channel through your Configuring Your onyX vehicle s radio If you are satisfied with the sound quality you re done If this FM channel doesn t work well for you work down the list until you find an FM channel that allows you to hear XM clearly OR 2 Manually tune through your local FM channels Manually tune through your local FM channels on your vehicle s FM radio Turn on your vehicle s FM radio Start at 88 1 and use the Manual tune function on your vehicle s FM radio to tune through each FM channel one by one 88 1 followed by 88 3 etc to locate channels that aren t being used by a local FM radio station Write down each FM channel that has only static or silence on it until you reach 107 9 Once you have created your list of available FM channels you will need to find the one that provides the best match for onyX Tune onyX to a favorite XM channel or to channel 1 if it s not yet activated Pick the first FM channel on your list and tune the FM radio to that channel Then tune the onyX to the same FM channel Refer to Set and Select an FM Channel on page 82 You should hear the XM channel through your vehicle s radio If you are satisfied with the sound q
25. e shown but not M Rock the artist and song show information Instead a ee lock icon and the word Locked is shown If 54 Lithium you scroll through the channels using Wand A Live Selling the Drama the locked channels are skipped and not 55 A Locked displayed If you attempt to tune to a locked channel either MEET MON by using direct tune or through the category list Phish Backwards Down you ll be prompted to enter your 4 digit code When the correct code is entered you ll be able to tune to and listen to the channel All locked channels become unlocked and will remain unlocked until you turn the onyX Off and back On In the category list the previously locked channels will show an unlocked icon h To turn Parental Controls On or Off 1 Press menu 2 Press W to scroll to and highlight Parental Controls Press the Select button e If this is the first time you want to turn on Parental Controls Parental Controls will be highlighted Press the Select button You will be prompted to select a 4 digit code i For each digit press one of jm the O 9 keys and then press ff Enter Parental Code P to advance to the next digit Press ir you need to go back and edit a previous digit ii When you have selected all 4 digits of your code press the Select button iii The Code Confirmation screen will be displayed For your records write down the code you have selected Press the
26. ear of the Roof 1 Feed the antenna cable from the antenna underneath the rubber molding around the rear window Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the rear window and tuck the antenna cable underneath the molding Route the antenna cable around and down the window to the lowest point If your rear window does not have rubber molding we recommend consulting a professional installer 2 Route the antenna cable out of the window molding and into the rubber weather stripping around the trunk opening Lift the weather stripping from the opening and tuck the cable inside it then replace the weather stripping To avoid sharp bends in the cable run the cable inside the weather stripping for a few inches then remove the cable from the weather stripping inside the trunk Keep the cable away from hinges gears etc that could damage it 3 Route the cable out from the rubber weather stripping and along the trunk wall Continue routing the cable into the vehicle cabin through a conduit or along an existing wiring harness 4 Route the cable through the main cabin area under the interior trim towards the front of the vehicle Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath Avoid side airbag locations on back pillars and above the doors Airbag locations are marked with SRS logos Be careful no
27. elease M and Y to immediately tune to the next or previous channel 2 Press and hold 4 and Y to quickly scroll through the channels Release to tune to the channel that is displayed View a category Channels are organized into categories to make it easier for you to find the ones that suit your taste To view a category press dor P Rock 1 Scroll through the category Lithium using 4 and Y and find the Fiona Apple Fast As You channel you want Margaritaville 2 Press the Select button to Ken Boothe Freedom Str select the channel or press dor gt for the previous or next category Jam_ON String Cheese In Round T Eu TIP To briefly listen to each channel in the category scroll to and highlight Scan at the end of the category list and press the Select button Refer to Scanning Channels in a Category on page 59 to learn more about Scan Using Your onyX Direct Tune A channel can be tuned directly by entering the channel number using the number buttons 1 To directly tune a channel press direct Direct Tune Enter channel 62_ 2 Use the number buttons O 9 to enter the channel number and wait a moment until the channel is tuned or press the Select button to immediately tune to the channel Jump Depending upon how you configure the mode jump will either go to the traffic and weather channel of a selected city from a list of the 20 most congested cities or go to the last channel t
28. enna of the affected receiver Increase the separation between the SIRIUS XM equipment and the affected receiver Connect the SIRIUS XM equipment into an outlet on a circuit different from that to which the affected receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING The FCC and FAA have not certified this Satellite Radio Receiver for use in any aircraft neither portable nor permanent installation Therefore SIRIUS XM Radio Inc cannot support this type of application or installation Copyrights and Trademarks 2009 SIRIUS XM Radio Inc SIRIUS XM and all related marks and logos are trademarks of SIRIUS XM Radio Inc and its subsidiaries BBC and Radio One are trademarks of the British Broadcasting Corporation and are used under license BBC logo BBC 1996 Radio 1 logo BBC 2001 Cosmopolitan is a registered trademark of Hearst Communications Inc Elvis Radio logo EPE Reg U S Pat amp TM off IndyCar and Design are registered trademarks of Brickyard Trademarks Inc used with permission Major League Baseball trademarks and copyrights are used with permission of Major League Baseball Properties Inc Visit the official website at MLB com Games subject to availability and change and may not include all spring training games All rights reserved NASCAR is a registered trademark of the National Association for Stock Car Auto Racing Inc The NBA i
29. ensure that CIS GENIE io Gele eelo your vehicle s FM radio is tuned to the same FM channel TIP To configure the list of preset FM channels you need to find available SS FM channels in your area Refer to Find Available FM Channels in Your Area on page 79 Next refer to Set and Select an FM Channel on page 82 62 63 Special Features Color Themes You can change the color of the display screen to one of 6 color themes Blue Red Amber Yellow Silver or Teal You can coordinate the color theme with your vehicle dash lights and with the Trim Ring of your choice for your onyX The default color theme is blue To change the color theme 1 Press menu 2 Press to scroll to and highlight Color Theme Press the Select button 3 Press or to highlight the A oe desired color theme The onyX will immediately change to the selected color theme Press arrow keys to choose 4 Press the Select button to confirm and Select to confirm the selected color theme 5 Press and hold menu to return to the main display screen Trim Rings Your onyX has a changeable Trim Ring to style the radio to your liking The Trim Ring surrounds the Select button on the radio A total of three trim rings are included with your onyX including the one that is already installed in the onyX Radio To remove and replace the Trim Ring The Trim Ring can be removed by using the Trim Ring Remo
30. g and route it under the carpet toward the dashboard Coil any excess cable in a hidden location such as under the carpet keeping it away from any vehicle pedals or controls Secure the excess cable with wire ties 4 Bring the end of the cable out at the PowerConnect Vehicle Dock location Leave yourself enough cable so you can easily connect it to the antenna connector of the dock 5 Continue with Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter on page 37 e SUV 1 Feed the antenna cable underneath the rubber weather stripping of the rear tailgate window door and route the cable along the rear hatch Lift the weather stripping from the opening and tuck the cable inside it then replace the weather stripping Pull the cable out from weather stripping and route it into the cabin under the interior trim Avoid hinges or gears that could crimp or cut the cable 2 Route the cable through the SUV s main cabin area under the interior trim towards the front of the vehicle Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath Avoid side airbag locations on back pillars and above the doors Airbag locations are marked with SRS logos Be careful not to crimp or cut the cable 3 Bring the cable out from the trim near the front of the cabin and route it under Vehicle Installation t
31. gits of the code press the Select button If your code is correct the channel will be tuned All locked channels become unlocked and will remain unlocked until you turn the onyX Off and back On In the category list the previously locked channels will show an unlocked icon M 74 Where E 1N Where Else Can You Use Your onyX SIRIUS XM offers a variety of accessories that allow you to adapt your onyX Radio to your lifestyle and enhance your listening experience With these accessories you can effortlessly take your Satellite Radio listening experience from your vehicle to your home or office or on the go all with a single subscription e In the Home Office etc With a Home Kit you can play your onyX over an existing home office or other stereo system e In Other Vehicles With a Vehicle Kit you can enjoy your onyX in more than one vehicle e In Almost Any Location You Like With a desktop or portable Sound System you have the freedom to listen to your onyX where and when you want from your kitchen or den to the office to outside on the deck or at a picnic For more information on XM accessories or to purchase an accessory please visit your local retailer or www xmradio com accessories TE Configuring Your onyX Radio ID Your onyX has an alphanumeric ID which uniquely identifies the radio This ID is used during the activation process To display the Radio ID Radio ID 1 Press me
32. he carpet toward the dashboard or console Coil any excess cable in a hidden location such as under the carpet keeping it away from any vehicle pedals or controls Secure the excess cable with wire ties purchased separately 4 Bring the end of the cable out at the PowerConnect Vehicle Dock location Leave yourself enough cable so you can easily connect it to the antenna connector of the dock 5 Continue with Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter on page 37 e Convertible 1 Bring the antenna cable from the antenna into the trunk at the front edge of the trunk lid Keep any bends in the cable loose Tape or tie the cable along the inside of the trunk lid to the trunk lid hinge strut 2 Allow enough slack in the cable so the trunk lid can easily open and close and keep the cable away from hinges gears etc that could crimp or cut it Route the cable along the trunk wall and into the cabin through a conduit or along an existing wiring harness 3 Route the cable through the main cabin area under the interior trim towards the front of the vehicle Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath Avoid side airbag locations on back pillars and above the doors Airbag locations are marked with SRS logos Be careful not to crimp or cut the cable 4 Bring the cable out fr
33. ighlight Change My Code Press the Select button 7 You will be prompted to enter a new 4 digit code For each digit press one of the 0 9 keys and then press P to advance to the next Code Confirmation gt digit Press dis you need to go D back and edit a previous digit Your Parental Code is 8 The Code Confirmation screen will 3287 be displayed For your records You will need this code to change write down the code you have selected Press the Select button or turn off Parental Controls 9 Press and hold menu to return to Press Select to continue the main display screen To listen to a locked channel There are two ways to tune to a channel which has been locked The first is by directly tuning the locked channel and the second is to select the locked channel from a category list 1 2 3 Directly tune or select the locked channel To directly tune a locked channel i Press direct and enter the channel number using the 0 9 keys To select a locked channel from the category list i Press d or P to display the category list of the locked channel you wish to tune ii Press W to scroll to and highlight the locked channel Press the Select button You will be prompted to enter your existing 4 digit code For each digit press one of the O 9 keys and then press P to advance to the next digit Press dif you need to go back and edit a previous digit When you have entered all 4 di
34. ilted in different directions Adjust as necessary for your particular vehicle When the orientation is correct tighten the knob Knob Adhesive Foot Dock Mounting Plate 4 Clean the surface with the alcohol preparation pad and let it dry thoroughly 5 Peel off the adhesive liner Position press and hold the Dash Mount in place for 30 seconds IMPORTANT Allow the Dash Mount adhesive to cure dry for a minimum of 2 4 hours before using the mount The best adhesion occurs after 24 hours Eu TIP To remove carefully lift the adhesive pad with your fingers or a spoon dy Warming the pad with a hair dryer for several minutes will help soften the adhesive Vehicle Installation Installing the Vent Mount Extended Vent Clamps 1 Locate a vent with horizontal louvers sturdy enough to hold your PowerConnect Vehicle Dock and radio 2 If the vent louvers in your vehicle are recessed you may need to use the longer vent clamps with the Vent Mount If so remove the shorter vent clamps and install the longer ones into the Vent Mount Be sure to observe the orientation of the vent clamps as shown Remove End Cap Slide Short Vent Clamps Out MUS Slide Extended Vent Clamps In hooks on the rear of the vent louver 2 4 Rest the foot against the bottom of the vent 2 and adjust the tilt of the Vent Mount by repositioning the foot to a different adjustment hole 3
35. ions shown on the next several pages TIP Mount the antenna on the roof for most vehicles or trunk for convertibles where it has a clear view of the sky in all directions CAUTION Don t mount the antenna inside gt the vehicle for example on the dashboard CAUTION Don t mount the antenna on any D of the vehicle s front back or side pillars a CAUTION Don t mount the antenna close to a roof rack Adjust the rack so it s further away from the antenna or move the antenna closer to the center of the roof Vehicle Installation CAUTION Don t mount the antenna 5 close to another antenna Mount it at least 3 inches away Step 4 Route the Magnetic Mount Antenna Cable Before you begin routing the antenna cable read these general instructions for how to route and hide the antenna cable Then route your antenna cable according to the instructions which follow for your specific type of vehicle pe Use a blunt plastic putty knife a credit card a plastic knife or a similar blunt tool to lift the rubber window moulding Tuck the cable under the moulding around the window Feed cable under lt rubber moulding around window Vehicle Installation Route cable out from under rear windshield moulding and tuck into weatherstripping IT around trunk opening a lt Avoid sharp bends by running cable through weatherstripping f
36. le Dock from the Universal Xpress Car Kit rather than the PowerConnect Vehicle Dock included with your onyX radio you will need to complete some additional installation steps When you have completed these additional steps you can continue with the installation of your onyX AUX Connected Audio enabled through auxiliary line FM turned OFF When you are using the Universal Xpress Vehicle Dock the screen will initially display AUX Connected when you power on your onyX Ignore this message Once you have completed the steps below it will not be displayed again If you are connecting the audio through your vehicle s FM radio SureConnect or FMDA 1 Disable the AUX Detect feature Refer to AUX Detect on page 91 and disable AUX Detect 2 Turn the FM Transmitter in the onyX On Refer to Turn FM Transmitter On Off on page 98 and turn the FM Transmitter On 3 Continue with the installation If you are connecting the audio using the Aux In Cable or Cassette Adapter 1 Disable the AUX Detect feature Refer to AUX Detect on page 91 and disable AUX Detect TIP The FM Transmitter must be Off To verify that the FM Transmitter is C Off refer to Turn FM Transmitter On Off on page 98 2 Continue with the installation Configuring Your onyX Turn FM Transmitter On Off Turning the FM Transmitter On applies only if you are using the older model Vehicle Dock from the Universal Xpress C
37. m Press and hold menu to return to the or menu to cancel main display screen To enable AUX Detect Do this when radio is transferred to the PowerConnect Vehicle Dock from an older model Vehicle Dock 1 Press menu 2 Press Y to scroll to and highlight Factory Settings and press the Select button 3 AUX Detect will be highlighted and show as disabled Press the Select button again to toggle the setting to enabled 4 Press and hold menu to return to the main display screen Restore Defaults You can clear all of your personal settings such as favorite channels FM presets etc and return the radio to its original out of the box settings To reset onyX to factory defaults T NOTE Restoring defaults permanently removes all personal settings 1 Press menu 2 Press to scroll to and highlight Factory Settings and Are You Sure press the Select button All settings will be erased 3 Press YW to scroll to and highlight Restore Defaults and press the Select button Press Select to confirm 4 A warning screen will be or menu to cancel displayed If you are certain that HT nn you want to reset your onyX to the default settings press the Select button to confirm If you want to cancel press menu to return to Factory Settings Configuring Your onyX Demo Mode Your onyX has a demo mode that starts playing when for a prolonged period of time more than 5 minutes the radio either
38. n wipe the skin area with a cloth and then wash the skin thoroughly with soap and running water If the liquid crystal fluid comes into contact with your eyes flush the eyes with clean water for at least 15 minutes and seek medical care If the liquid crystal fluid is ingested flush your mouth thoroughly with water Drink large quantities of water and induce vomiting Seek medical care Make sure that you insert the PowerConnect Power Adapter all the way into the vehicle s cigarette lighter or power adapter socket e If you are using PowerConnect as your audio connection option it is advisable not to insert a multi outlet adapter into the same vehicle cigarette lighter or power adapter socket to simultaneously power other devices Some multi outlet adapters can prevent the PowerConnect feature from working properly When using this product it is always important to keep your eyes on the road and hands on the wheel Not doing so could result in personal injury death and or damage to your device accessories and or to your vehicle or other property Vehicle installation and radio configuration functions should not be performed while driving Park your vehicle in a safe location before beginning installation This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Your device should be placed in your vehicle where it will not interfere with the function of safety featu
39. n your list from step 5 Turn on your vehicle s FM radio if you have not already done so and tune it to this FM channel eu NOTE If you are using the Vehicle Dock from the Universal Xpress Car Kit instead of the PowerConnect Vehicle Dock which came with your onyX you will have to disable AUX Detect Refer to Using the Vehicle Dock From the Universal Xpress Car Kit on page 96 and complete the additional instructions before continuing with the next step The audio connection will be through your vehicle s FM radio but it is not PowerConnect MATCH FM CHANNELS 8 Set your onyX to transmit on the same FM channel that you have selected in step 7 i Press menu ii Press W to scroll to and highlight FM Settings and press the Select button iii FM Channels will be highlighted If it is not highlighted press Y to scroll to and highlight FM Channels Press the Select button iv Press Y to scroll to and highlight the storage location FM 2 and press the Select button Tune to the available FM channel you found in step 7 Press 4 Vehicle Installation 7 and P to tune in steps of 2 i e FM Channels 99 3 to 99 5 Press W and 4 to tune in steps of 1 i e 99 3 to FM 1 97 9 current 100 3 Press the Select button to select the FM channel v Start Using is highlighted Press the Select button vi The FM channel you selected will be confirmed on the display screen The
40. nu 2 Radio ID will be highlighted If it is Your Radio ID is not highlighted press Y to scroll to and highlight Radio ID Press the A234B456 Select button The Radio ID will be displayed 3 Press and hold menu to return to the main display screen Find Available FM Channels in Your Area Before attempting any of the procedures below you should park your vehicle in a safe location Do not attempt to set up your FM channels or any onyX function while driving PowerConnect allows you to listen to XM audio through your vehicle s FM radio You will first need to find an available FM channel which is a channel that is not being used by an FM radio station in your area When you tune your FM radio to an available channel you should only hear static or silence not talk or music Once you have found an available channel you need to tune onyX s built in transmitter to the same channel to receive XM sound through your vehicle s radio We recommend one of the following methods to find an available FM channel 1 Use the SIRIUS XM FM Channel Finder Use the SIRIUS XM FM Channel Finder at www xmradio com fmchannel Go to the website and enter your zip code The Channel Finder will suggest a list of available FM channels in your area For convenience write down or print out the list Tune onyX to a favorite XM channel or to channel 1 if it s not yet activated Turn on your vehicle s FM radio Pick th
41. o which you were listening TIP By default jump is configured to tune to a traffic weather channel To O select a city for traffic and weather or to configure jump to tune to the last channel listened to refer to Jump Settings on page 86 Return to Main Display Screen Pressing and holding menu in most instances will return you to the main display screen In some cases you may need to follow the instructions on the display screen Using Your onyX Favorite Channels You can set up to 10 of your favorite channels so you can easily access them Each favorite channel can be assigned to a number button To assign a favorite channel to a number zz button ee Favorite Saved 1 Tune to the desired channel 26 The Pulse 2 Press and hold the number button saved as 0 9 you want to assign to that favorite Favorite 1 channel To listen to a favorite channel 1 Press the number button O 9 that was assigned to the desired favorite channel Eu TIP When you are at the main display screen press lt to see your list of favorite CS channels Scroll to highlight a favorite and press the Select button to listen to that channel Scanning Channels in a Category You can scan a category and listen to each channel for 10 seconds before the next channel is automatically tuned If you want to stay tuned to the channel being played and stop the scan just press the Select button To scan a category 1 P
42. om the trim near the front of the cabin and route it under the carpet toward the dashboard or console Coil any excess cable in a hidden location such as under the carpet keeping it away from any vehicle pedals or controls Secure the excess cable with wire ties purchased separately 5 Bring the end of the cable out at the PowerConnect Vehicle Dock location Leave yourself enough cable so you can easily connect it to the antenna connector of the dock 6 Continue with Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter on page 37 e Pickup Truck 1 Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath it 2 Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner 3 At the lowest corner of the Vehicle Installation windshield route the cable out of the windshield molding and into the rubber weather stripping around the door opening Lift the weather stripping from the opening and tuck the cable inside it then replace the weather stripping Run the cable inside of the weather stripping to the bottom of the door opening 4 Pull the cable out of the weather stripping at the bottom of the door opening and route it under the carpet toward the dashboard Coil any excess cable in a hidden location such as under the carpet keeping it away from any vehicle pedals
43. or controls Secure the excess cable with wire ties 5 Bring the end of the cable out at the PowerConnect Vehicle Dock location Leave yourself enough cable so you can easily connect it to the antenna connector of the dock 6 Continue with Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter on page 37 Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter 1 Plug the Magnetic Mount Antenna into the silver ANT connector on the PowerConnect Vehicle Dock 2 Insert the PowerConnect Power Adapter into your vehicle s cigarette lighter or power adapter socket 3 Plug the PowerConnect Power Adapter into the red PWR connector on the dock Vehicle Installation Step 6 Connect the Audio To play audio through your vehicle s stereo or FM radio decide on one of the following audio connection options e Option 1 Best Use the Aux In Cable if your vehicle s stereo system has an auxiliary input connection Refer to your vehicle s owners manual to find the location of the auxiliary input jack or consult the vehicle dealer Eu TIP The auxiliary input jack may be located on the face plate of the vehicle D radio on the back of the radio anywhere on the front dash panel inside the glove compartment or inside the center console in between the front seats e Option 2 Better Use a Cassette Adapter if your vehicle has a built in cassette
44. or several inches Pull weatherstripping from trunk opening Tuck cable into weatherstripping Route cable through weatherstripping several inches to avoid sharp bends Pull cable out of weatherstripping and route through trunk to cabin Route cable out of window moulding and into weather stripping around trunk opening gap or conduit along existing wiring harness Route cable along trunk wall and into cabin Vehicle Installation Use a blunt plastic putty knife or similar blunt tool to lift edge of interior trim and tuck cable under trim Continue towards front of vehicle Route cable under trim or upholstery Continue routing cable under trim or carpet towards front of vehicle Route cable from trunk under interior trim into cabin and towards front of vehicle Continue routing cable under carpet or console to radio location Coil excess cable under Pull carpet lt carpet or mat or mat AS Bring cable out from trim Bring cable out from trim and route under carpet to dashboard or console TIP Always be careful to include enough slack in your cable to CS accommodate open doors or trunk lids Use things typically found around the home like electrical tape to secure cables in areas so that hinges do not pinch the cable with the door Hide any excess cable in the trim Vehicle Installation e Sedan Coupe With Antenna Placed at the R
45. or waste disposal when discarding packaging and electronic appliances Your radio is packaged with cardboard polyethylene etc and does not contain any unnecessary materials FCC Statement The user is cautioned that changes or modifications not expressly approved by SIRIUS XM Radio Inc can void the user s authority to operate this device This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the installation instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving ant
46. ord the XM Radio ID in the space provided below Refer to these numbers whenever you call your dealer regarding this product Radio Model Number XDNX1 XM Radio ID xmradio com SIRIUS XM Radio Inc 1221 Avenue of the Americas New York NY 10020 1 800 967 2346 2009 SIRIUS XM Radio Inc XDNX1UG 092909a
47. r into the YO Joya ln LO fem O connector on the A Fa ze dock Fi Insert the Cassette Adapter into the vehicle s cassette deck You may need to turn on your vehicle s stereo system in order to do so Insert the dock into the mount Insert your onyX into the dock Power on your onyX by pressing the Power button Be sure the vehicle is outside and the antenna has a clear view of the sky Verify that you are receiving the XM signal There should at least be one bar on the lower left corner of the main display screen that denotes antenna signal Vehicle Installation strength You can also press menu and then press to scroll to and highlight Signal Indicator Press the Select button The Satellite and Terrestrial bars show the strength of the signal being received If the signal reception is good press and hold menu to return to the main display screen Signal Indicator 7 Ensure onyX is tuned to channel 1 Upon power up onyX should tune to channel 1 by default when it s not yet activated If it s not on channel 1 refer to Listening to Satellite Radio on page 55 to learn about how to tune a channel 8 If you haven t done so turn on your vehicle s stereo system Set it to play input from the cassette source 9 You should hear XM channel 1 through your vehicle s stereo system You are now ready to activate your onyX 10 The audio level output of the onyX can
48. r use it to go back to the previous channel to which you were listening PowerConnect Vehicle Dock Color Coded Connections The color coded PowerConnect Vehicle Dock makes it simple to connect Just match the colors on the cable ends to the colors on the dock to see what goes where Rear View AUDIO Green ANT Silver PWR Red FM Blue Connection for Aux In Connection for Connection for Connection for Cable or optional the Magnetic PowerConnect optional FM Direct Cassette Adapter Mount Antenna Power Adapter Adapter sold sold separately separately Introduction Wire Guide The PowerConnect Vehicle Dock has a wire guide at the top rear that can help you to organize the cables and wires connected to the dock If you need to bring a Cable or wire from one side of the dock to the other utilize the wire guide by looping the cable though the wire guide as shown Wire Guide Veh IC 13 Vehicle Installation Step 1 Choose a Location for Your Radio When installing the onyX in your vehicle choose a location where it will not block your vision interfere with the controls or obstruct the air bag The location should be easily accessible and provide good visibility of the display and should not be located where it will be in direct sunlight which will affect the visibility of the display screen Several examples of the onyX mounted in a vehicle are shown A is the on
49. radio to an available channel you should only hear static or silence not talk or music We recommend one of the following methods to find an available FM channel a Use the SIRIUS XM FM Channel Finder at www xmradio com fmchannel Go to the website and enter your zip code The Channel Finder will suggest a list of available FM channels in your area For convenience write down or print out the list OR b Manually tune through your local FM channels on your vehicle s FM radio Locate and create a list of channels that aren t being used by any FM radio station Write down the list Once you have created your list of available FM channels you will need to find the one that provides the best match for onyX Eu TIP You ll need to use the Manual tune function on your vehicle s FM radio to tune through every FM channel one by one Turn on your vehicle s FM radio Start at 88 1 and use the Manual tune function on your vehicle s FM radio to tune through each FM channel one by one 88 1 followed by 88 3 etc to locate channels that aren t being used by a local FM radio station Write down each FM channel that has only static or silence on it until you reach 107 9 6 Ensure onyX is tuned to channel 1 Upon power up onyX should tune to channel 1 by default when it s not yet activated If it s not on channel 1 refer to Listening to Satellite Radio on page 55 to learn about how to tune a channel 7 Pick the first FM channel o
50. res e g deployment of airbags Failure to correctly place device may result in injury to you or others if the unit becomes detached during an accident and or obstructs the deployment of an airbag What s in the Box om onyX Radio PowerConnect Vehicle Dock Aux In Cable Vent Mount and Extended Vent Clamps Trim Rings Trim Ring Removal Tool cS N Acon Prep Pad 0 N Antenna amp Dash Mount PowerConnect Power Magnetic Mount Alcohol Preparation Pads Adapter Antenna Introduction onyX Functions Up and Down Arrows Scroll through lists and preview channels also highlight menu options Left and Right Arrows Search for channels by category ony Li 2 Cs 4 1s Ls 7 48 9 0 creer Number Buttons Select your favorite channels also enter a channel number Trim Ring Changeable decorative Trim Ring Direct Button Press first before entering the channel number to directly tune to a channel Power Button Turn radio on and off Select Button Press to confirm selection for channel and menu items Menu Button Access advanced features and configuration options also press and hold to return to main display screen FM Button Access and cycle through FM presets Jump Directly access traffic and weather of the 20 most congested cities o
51. ress d or D until the desired category is displayed 2 Scroll down to highlight the last item in the category which will be Scan and the category name 3 Press the Select button The scan will begin 4 Press the Select button to stop the scan and continue to listen to the channel currently being played or press V or 41 to return to the channel you were listening to before you began the scan Pop Scanning BBC Radio 1 70s on 7 Green Day American Idio Bee Gees You Should Be Pop2K 80s on 8 David Archuleta Crush The Hooters And We Dan Scan Pop 90s on 9 Oasis Champagne Super Using Your onyX FM Presets FM presets make it easy to quickly access stored FM channels and choose a new FM channel from them Use FM presets when you use PowerConnect to listen to your onyX through your vehicle s FM radio Refer to Option 3 PowerConnect Installation Instructions on page 43 for more information To start using a different FM preset 99 3 FM 1 Press FM to display the current FM preset Set your vehicle radio to the 2 To display and select the next FM above channel to enable audio preset press FM The radio will tune to the displayed FM channel If the preset is the one you want press menu or wait for the screen to timeout 3 Repeatedly pressing FM will cycle through the FM presets 103 7 FM 4 Set your vehicle s FM radio to the same FM channel Set your vehicle radio to the IMPORTANT You need to
52. t to crimp or cut the cable Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the dashboard or console Coil any excess cable in a hidden location such as under the carpet keeping it away from any vehicle pedals or controls Secure the excess cable with wire ties purchased separately Bring the end of the cable out at the PowerConnect Vehicle Dock location Leave yourself enough cable so you can easily connect it to the antenna connector of the dock Continue with Step 5 Connect the Magnetic Mount Antenna and PowerConnect Power Adapter on page 37 Vehicle Installation e Sedan Coupe With Antenna Placed at the Front of the Roof 1 Feed the antenna cable from the antenna underneath the rubber molding around the windshield Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath the molding Route the antenna cable around and down the windshield to the lowest point 2 At the lowest corner of the windshield route the cable out of the windshield molding and into the rubber weather stripping around the door opening Lift the weather stripping from the opening and tuck the cable inside it then replace the weather stripping Run the cable inside of the weather stripping to the bottom of the door opening 3 Pull the cable out of the weather stripping at the bottom of the door openin
53. tically detect a connection made to the AUDIO connector of the PowerConnect AUX Detect enabled Vehicle Dock by an Aux In Cable or Restore Defaults Cassette Adapter AUX Detect is enabled by default IMPORTANT If you are using the C5 PowerConnect Vehicle Dock which came with your onyX Radio AUX Detect should remain enabled If you are using the older model Vehicle Dock from the Universal Xpress Car Kit and plan to use PowerConnect or FMDA as the audio connection option you will need to disable AUX Detect Please read the additional instructions Using the Vehicle Dock From the Universal Xpress Car Kit on page 96 Once AUX Detect is disabled you ll have to turn the FM Transmitter On Refer to Turn FM Transmitter On Off on page 98 To disable AUX Detect Do this only when using the older model Vehicle Dock 1 Press menu Configuring Your onyX 2 Press to scroll to and highlight Factory Settings and press the Select button 3 AUX Detect should be highlighted and show as enabled Press the Select button to toggle the setting 4 A warning screen will be displayed Press the Select button to confirm o that you want to disable AUX Detect Disable AUX Detect If you want to cancel press menu to Disable only if using vehicle dock return to Factory Settings AUX from Universal Xpress Car Kit Detect will remain enabled Otherwise leave it enabled 5 AUX Detect will show as disabled Press Select to confir
54. to go back to the previous channel to which you were listening e Parental controls Easily lock and unlock channels with mature content Please read the entire user guide before using your onyX Safety and Care Information IMPORTANT Always read and understand all the instructions to avoid C injury to yourself and or damage to your device SIRIUS XM Radio Inc disclaims all responsibility for damage from data loss due to breakdown repair or other causes Do not expose to extreme temperatures above 140 F or below 4 F or above 60 C or below 20 C Do not expose to moisture Do not use device near or in water Do not touch the device with wet hands e Do not let any foreign matter spill into device e Do not store in dusty areas e Do not expose to chemicals such as benzene and thinners Do not use liquid or aerosol cleaners Clean with a soft damp cloth only Do not expose to direct sunlight for a prolonged period of time and do not expose to fire flame or other heat sources Do not try to disassemble and or repair device yourself Do not drop your device or subject it to severe impact e Do not place heavy objects on device e Do not subject device to excessive pressure If the LCD screen is damaged do not touch the liquid crystal fluid Introduction Warning e Opening the case may result in electric shock e If the liquid crystal fluid comes in contact with your ski
55. tton 7 Alist of all the categories and the channels in each category will be displayed Press V and 4 to scroll to and highlight a channel or category you want to lock Press the Select button A lock icon A will be displayed to the left of the channel or category you locked To unlock a locked channel or category simply highlight the locked channel or category and press the Select button The lock icon will disappear indicating the channel or category is unlocked Locked Channels Locked Categories Locked Channels Locked Channels Rock a Rock ia Deep Tracks Deep Tracks Hair Nation a Hair Nation xL Liquid Metal a xL Liquid Metal SIRIXM U a SIRIXM U 8 You can continue to lock and unlock as many channels or categories as you wish When you are finished press and hold menu to return to the main display screen To change your code 1 Press menu 2 Press V to scroll to and highlight Parental Controls Press the Select button 3 You will be prompted to enter your existing 4 digit code For each digit press one of the O 9 keys and then press P to advance to the next digit Press dis you need to go back and edit a previous digit Special Features 4 When you have entered all 4 digits of the code press the Select button 5 If Parental Controls are shown as Off press the Select button to turn it On otherwise continue with the next step 6 At the Parental Controls screen Press W to scroll to and h
56. uality you re done If this FM channel doesn t work well for you work down the list until you find an FM channel that allows you to hear XM clearly NOTE You may find an FM channel with static or silence that does not work with onyX It is possible that some type of inaudible interference is present that prevents reception of the onyX broadcast Your only options are to use another FM channel or a different audio connection method TIP If you regularly drive from one location to another such as your daily commute you may need to use different FM channels along your route for best performance If this is the case we recommend saving the best FM channels as presets on your FM radio and onyX Then you simply select and match the best channel for the area you are in zu TIP It will be much more difficult to find available FM channels in large O cities than in most suburban or rural locations A direct audio connection using the Aux In Cable Cassette Adapter or professional installation is your best solution if you drive in or near large metropolitan areas Zu NOTE The SIRIUS XM FM Channel Finder relies on data from the Federal O Communications Commission The data may not reflect the latest stations in your area In addition local geography and weather conditions can impact reception so your results may be different from the list Eu NOTE The performance of FM radios are different based on manufacturer D and
57. ume control Use the volume control on your vehicle s stereo instead To adjust the audio level 1 Press menu Set Audio Level 2 Press Y to scroll to and ie highlight Audio Level and press the Select button 3 Press to decrease or P to GE increase the audio level 4 Press the Select button to confirm the new audio level Press arrow keys to adjust and Select to confirm 5 Press and hold menu to return to the main display screen Configuring Your onyX Signal Indicator For best reception your Magnetic Mount Antenna should have an unobstructed view of the XM satellites In large cities there are terrestrial transmitters ground repeaters to help increase the signal coverage Your onyX can display the received strength of the satellite and terrestrial signals being received To display the signal strength 1 Press menu Signal Indicator 2 Press to scroll to and highlight Signal Indicator and press the Select button 3 The Satellite and Terrestrial bars show the strength of the signal being received 4 Reposition the antenna if you are having trouble receiving the signal Be sure your vehicle is outside with an unobstructed view of the sky 5 Press and hold menu to return to the main display screen Factory Settings The factory settings menu has two choices AUX Detect and Restore Defaults AUX Detect AUX Detect allows the onyX Radio to Factory Settings automa
58. val Tool Placing this tool against the Trim Ring and with mild pressure while turning the tool it will loosen or tighten the Trim Ring depending upon which direction you Special Features turn the tool 1 Place the Trim Ring Removal Tool on the Trim Ring on the radio Use care to align the tool so it s centered on the Trim Ring eI2I 2I 1 2 1 12 1212101 2 Using mild pressure to keep the tool against the Trim Ring rotate the tool counter clockwise until it will not rotate any further 3 The Trim Ring is now loose Turn the onyX over and the Trim Ring should fall out If it does not gently tap the back of the radio until it does 4 Turn the radio face up again and insert the new Trim Ring into the radio Align the Trim Ring Removal Tool on the Trim Ring on the radio Use care to align the tool so it s centered on the Trim Ring 213 14 Ls Ls 7 13 Le 6 Using mild pressure to keep the tool against the Trim Ring rotate the tool clockwise until it will not rotate any further The new Trim Ring is now installed Special Features Parental Controls Your onyX has a parental control feature which will allow you to lock access to channels or lock access to an entire category A 4 digit code controls access to the locked channel or locked category When you browse a category the locked channel number or locked category will b
59. vehicle style Some may not work well with the type of FM transmitter used by onyX This is why we recommend a direct audio connection using the Aux In Cable or Cassette Adapter if they can be used in your vehicle Professional installation can also resolve almost any performance issue Configuring Your onyX Set and Select an FM Channel The onyX allows you to easily store i e preset up to 5 different FM channels At any time you can select any one of these 5 FM presets to transmit audio from the onyX to your vehicle s FM radio Having a choice of 5 FM presets also makes it easy to switch to the appropriate FM channel as you travel from one area to another Each FM preset is stored in its own storage location You can easily add or edit the FM preset in any one of the 5 storage locations IMPORTANT The onyX and the vehicle s FM radio need to be tuned to the same FM D channel in order to hear the audio TIP The FM 1 storage location is preset with FM channel 97 9 To set and select an FM preset FM Channels 1 Press menu FM 1 97 9 2 Press to scroll to and highlight FM 2 99 3 current ee and press the Select EM 3 103 7 3 FM Channels will be highlighted If it FM 4 is not highlighted press Y to scroll FM 5 to and highlight FM Channels Press the Select button 4 Press to scroll to and highlight the storage location FM 1 to FM 5 you want to set and press the Select button You can choose 5 6

User Guide - VOXX International Corporation

Contents

Download Pdf Manuals

Related Search

Related Contents