Manual Operation
Contents
1. cccceccc eee e eect eee eee ects eee eee ee ememete e ite eterni serere nns 13 Test the reversing sensitivity ccc eee eee eee nee ene ee eee eee sesenta heme nnne nennen nnns 15 How to learn or erase the remote 0 cece cee eee teen Ies meses ee eee enne 15 How to use the remote to control the operator ssssssssssssses Immer 15 Trouble Shooting cde etta s EE ae spas XE NERA ata ansaid aa NU EX RE XERRHRRA REM C ERE DO Eu ram Ea es 16 Maintenance cg id aeu geet ia he ti ERE ene Sea RIIV RAE ETE Be nin 17 Thank you for purchasing DSR600 DSR1000 sliding gate operator We are sure that the products will be greatly satisfying as soon as you start to use it The product is supplied with a user s manual which encloses installation and safety precautions These should be read carefully before installation and operation as they provide important information about safety installation operation and maintenance This product complies with the recognized technical standards and safety regulations General Safety A WARNING An incorrect installation or improper use of the product can cause damage to persons animals or properties Scrap packing materials plastic cardboard polystyrene etc according to the provisions set out by current standards Keep nylon or polystyrene bags out of children s reach This product was exclusively designed and manufactured for the use specified in the present2. 1 pe LM 135 i pe iLMT34 1 po LMt62 gt Back up battery boul pc Alan Lamp 1 pc Phoinbell Beam System Wall push buttar LMA UM aO 1 sat LM1 a d pe LMT Hv Keypad wiraless Solar panel f pe Supporting frame for sotar Bracket for solar panel 1 pe iLMTOS LMI geras 1 pop LM 115 1 pa LM 116 Mounting post ra for Keypad PED OL 1 pe LMTOT ae Wired Keypad 1 pz LMTOB Loop Detector ID card LMT O i i1 per LMI Technical Specifications amp Features Specifications Power supply 120V 60HZ or 230V 50HZ Motor 24VDC Absorbed power DSR600 180W DSR1000 350W Gate moving speed 7 9 second 20 cm second Max gate weight DSR600 600KGS DSR1000 1000KGS Max torque DSR600 12Nm DSR1000 24Nm Environmental conditions from 15 C to 40 C Protection class IP44 Dimensions 45 x 29 x 37 CM Features Soft start and soft stop Midway mode Reliable rolling code technology Emergency release key in case of power failure Stop Reverse in case of obstruction during gate opening closing Built in adjustable auto close 0 30 60 90 seconds Built in max 90 seconds Motor running time MRT for multiple safety protection Reliable electromagnetism limit for easy adjustment Optional accessories Installation Overview Siding Gate Alarm Lamp 1 Higher Magnet Concrete Pad Gate Operator Rack Lower M
3. documentation Any other use not specified in this documentation could damage the product and be dangerous The factory declines all responsibility for any consequences resulting from improper use of the product or use which is different from that expected and specified in the present documentation Do not install the product in explosive atmosphere The factory declines all responsibility for any consequences resulting from failure to observe Good Technical Practice when constructing closing structures door gates etc as well as from any deformation which might occur during use Disconnect the electrical power supply before carrying out any work on the installation Also disconnect any buffer batteries if fitted Fit an omnipolar or magnetothermal switch on the mains power supply having a contact opening distance equal to or greater than 3 5 mm Check that a differential switch with a 0 03A threshold is fitted just before the power supply mains Check that earthing is carried out correctly connect all metal parts for closure doors gates etc and all system components provided with an earth terminal Fit all the safety devices photocells electric edges etc which are needed to protect the area from any danger caused by squashing conveying and shearing Position at least one luminous signal indication device blinker where it can be easily seen and fix a Warning sign to the structure The factory declines all r
4. retest the gate operator Failure to adjust and retest the gate operator properly can increase the risk of injury or death 5 Use the emergency release only when the gate is not moving 6 KEEP GATES PROPERLY MAINTAINED Read the owner s manual Have a qualified service person make repairs to gate hardware 7 The entrance is for vehicles only Pedestrians must use separate entrance 8 SAVE THESE INSTRUCTIONS Safety Instructions for Installation A Install the gate operator only when 1 The operator is appropriate for the construction of the gate and the usage Class of the gate 2 All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet 1 22 m above the ground to prevent a 2 1 4 inch 57 2 mm diameter sphere from passing through the openings anywhere in the gate and in that portion of the adjacent fence that the gate covers in the open position 3 All exposed pinch points are eliminated or guarded 4 Guarding is supplied for exposed rollers B The operator is intended for installation only on gates used for vehicles Pedestrians must be supplied with a separate access opening The pedestrian access opening shall be designed to promote pedestrian usage Locate the gate such that persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate C The gate must be installed in a location so that enough clearance is supplied betw
5. shall not cause the operator to start H A minimum of two 2 WARNING SIGNS shall be installed one on each side of the gate where easily visible Keep Tann Glee um ccm are nr 1 Maca dus Can Cause injury Cir Beare For a gate operator utilizing a non contact sensor in accordance Usage Class 1 See instructions on the placement of non contact sensors for each Type of application 2 Care shall be exercised to reduce the risk of nuisance tripping such as when a vehicle trips the sensor while the gate is still moving in the opening direction 3 One or more non contact sensors shall be located where the risk of entrapment or obstruction exists such as the perimeter reachable by a moving gate or barrier J For a gate operator utilizing a contact sensor in accordance with Usage Class 1 One or more contact sensors shall be located where the risk of entrapment or obstruction exists such as at the leading edge trailing edge and post mounted both inside and outside of a vehicular horizontal slide gate 2 One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate 3 One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate 4 A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage 5 Awireless contact sensor such as one that trans
6. LockMaster Sliding Gate Operator User s Manual Model DSR 600 1000 Please read and follow all warnings precautions and instructions before installation and use Periodic checks of the operator are required to ensure safe operation For residential use only Save this manual Table of Contents General Safety 2 reddent etre qao SM DEA AEE epo qued etded iunt Hees TREE wha den eee te Pe Dind 2 Important Safety Instructions 2 c cece cece a eee ee nent eee eee meme eene e e eterni n rrr riri EN 3 Preparation for Installation 2220 setae derit Ett rn ee putet sb eying rude ee Eras Re Servo hr Ey ra Se donet Pen nas 5 pcs EE 6 Optional Accessories Part List cccc eee c eee c eect e eee ttt trtt ee Ie hehehe erint erre ri retirer 7 Technical Specifications amp Feature ssssssssssssssssssssssssssess sese eese e eese esee re enne 7 Installation Overview orisii o em e Cre rne eva Sy oa ERR EX RR eR fe Ga poe eire xo arose cue re d RARE E 8 Installation of th Operator 1 cete etd e ee EE ER Pe SER ER HR panes RATER AE sed rd x Os gni pei EE HR eR REIS 8 Manual Operation MM E 9 Fil The RACK 22 ore REED e tee api utei t pL P AV M 10 Installation of the Limit SWIER sesers nenesa cece eee eee ee I III Ime hn aces canes ee esa ease eren 11 Connecting the Control Board ccccecec cece eee e eee eee ee e eee ents ne is ere e etii ri sten 12 Setting of the Control Board
7. agnet Pivatacell Installation of the Operator Caution Be sure that the operator is installed in a level and paralleled position and is properly secured Improper installation could result in property damage severe injury and or death Before starting installation ensure that there is no point of friction during the entire movement of the gate and there is no danger of derailment Ensure that the Warning Signs are present Gate Operator Hex Bol MBx3U 4 pcs vat Pu rt Spring Washer B 4 pes Plain Washer 24 4 pcs Hex Mut M10 4 pcs Spring Washer i 10 4 pes x a Fapa Base Piaje l 3 1 pe Anchor Bii 4 pos E 4 pcs L Cable i 5 AU T Conduit Concrete Pad E Necessary Tools The following tools may be necessary to install the Gate operator You will need screwdrivers an electric drill wire cutters and a wire stripper a socket set and possibly access to a welder When install the operator you should build a concrete pad to support the base plate of operator in order to maintain proper stability The installation proceeds are as follows 1 Dig a hole for a concrete pad which should be approximately 60 x 32 x 35cm 24 x 13 x 14 It may protrude 10 cm 4 above ground and 25 cm 10 in depth underground Increase the pad height if necessary to protect the system from flooding heavy snow etc 2 Prepare one or more conduits for the electrical cables before pour concrete Re
8. ate stops are positioned A WARNING Remember that control devices are intended to facilitate gate operation but can not solve problems due to any defects or deficiency resulting from failure to carry out correct installation or maintenance Take the product out of its packing and inspect it for damage Should it be damaged contact your dealer Remember to dispose of its components cardboard polystyrene nylon etc according to the current prescriptions Refer to the following Figures for gate installation Using the post or wall as a stop either directhy or indirectly is not recommended sn as to protect Ihe post ar wall against damaging shock from the sliding gate Positive Stop in fully closed position It is suggestion that there is a 4 10cm distance at least between the gate edge and the gate wall when the gate is fully open ja 4 minimum Positive Stop in fully apening position lt lt Opening Parts List a C Remate Control Anchor Bolt 4 pcs Magnet bracket 2 pcs q10 Lock Washer ERG MBx3D Bolt 4 pcs ama Lima Duty Plastic Rack Reinforced with Steel Plastic Rack Reinforced with Steel _1005mm Nipes Optional 1005mmxN pcs Optional Galvanized Stee Rack 1O05mm Nipcs Optional Optional Accessories Parts List Optional Back up battery 1 sat LMS Battery emergency changer Extamal Receaver Video Door Phone
9. ated or damaged Turn power off and allow board to cool for several minutes then reset Replace the transformer if the symptom still exists 3 Check the fuse in the control board Replace the fuse if it was burnt out 4 Check the control board Replace the control board if necessary Power LED is ON Operator will not run 1 Check to be sure the beam is not blocked if a photocell is used as a secondary entrapment prevention device If a photocell is not used terminal 8 should be shorted with terminal 9 by a jumper wire 2 Check the motor Release the clutch then disconnect the wires of the motor from terminal 1 and 2 Connect the wires to the terminal 16 and 17 directly the motor should run and then exchange the wires the motor should run in the opposite direction If the motor runs in both directions please check the other parts listed below 3 Check the limit switches Use a jumper wire to short terminal 4 with terminal 3 and 5 and then use a keying device to operate the operator replace the higher limit switch if the motor couldn t run in clockwise direction and replace the lower limit switch if the motor couldn t run in counter clockwise direction 4 Replace the control board if the motor runs in all steps above not work Remote control does 1 The indicator light of remote control is not on Check the battery in your remote control Replace the battery if necessary 2 The distance you use the remote is too
10. ches The YELLOW wire of the limit switches should be connected into the 3 terminal The BLACK wire of the limit switches should be connected into the 4 terminal The RED wire of the limit switches should be connected into the 5 terminal 3 Alarm Lamp 24VDC The WHITE wire of the alarm lamp should be connected into the 6 terminal The RED wire of the alarm lamp should be connected into the 7 terminal 4 Photocell Use a 2 core cable to connect the terminal of the photocell s emitter to the 16 terminal the terminal to the 17 terminal Also the and terminals of the photocell s receiver should be connected to the 16 and 17 terminals in parallel Use another 2 core cable to connect the OUT terminal of the receiver to the 8 terminal the COM terminal to the 9 terminal 5 Push Button The push button should be wired to the 10 and 11 terminals The gate operator works alternately by pushing the button open stop close stop open 6 Loop Detector First insert the LOOP DETECTOR BOARD into the CONTROL BOARD and then connect the twisted pair to the 14 and 15 terminals 7 External Receiver The BROWN wire of the external receiver should be connected into the 11 terminal The BLACK wire of the external receiver should be connected into the 16 terminal The RED wire of the external receiver should be connected into th
11. e 17 terminal 8 Wired Keypad 24VDC The RED wire of the wired keypad should be connected into the 17 terminal The BLACK wire of the wired keypad should be connected into the 16 terminal The BLUE wire of the wired keypad should be connected into the 10 terminal The WHITE wire of the wired keypad should be connected into the 11 terminal 9 Battery The negative terminal of the battery should be wired to the 18 terminal The positive terminal of the battery should be wired to the 19 terminal 10 Solar Panel The negative terminal of the solar panel should be wired to the 20 terminal The positive terminal of the solar panel should be connected to the 21 terminal Gonia Board ee Setting Of the Control Board 1 DIP Switches The DIP switches are used to set the running time of the motor in midway mode fine adjust the soft stop period of the motor auto close time of the gate operator and fast change the open close direction which is determined by the position of the gate operator installed 13 DIP Switch 1 2 Running time of the motor in Midway Mode This mode enables user to drive the vehicle through the gate quickly when the gate opens to certain width DIP Switch 1 ON 2 Seconds OFF 0 DIP Switch 2 ON 4 Seconds OFF 0 NOTE The midway mode function would be disabled if both DIP switches are turned off Factory default setting is disable shel Jal be E g E 2345678 Run
12. een the gate and adjacent structures when opening and closing to reduce the risk of entrapment D The gate must be properly installed and work freely in both directions prior to the installation of the gate operator Do not over tighten the operator clutch or pressure relief valve to compensate for a damaged gate E For gate operators utilizing Type D protection 1 The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving 2 The placard provided marked in letters at least 1 4 in 6 4 mm high with the word WARNING and the following statement or the equivalent Moving Gate Has the Potential of Inflicting Injury or Death Do Not Start Gate Unless Path is Clear shall be placed adjacent to the controls 3 An automatic closing device such as a timer loop sensor or similar device shall not be employed 4 No other activation device shall be connected F Controls intended for user activation must be located at least ten feet 10 away from any moving part of the gate and where the user is prevented from reaching over under around or through the gate to operate the controls Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use Be gure to mount ALL operating devices A clearly aut of reach of through gale G The Stop and or Reset button must be located in the line of sight of the gate Activation of the reset control
13. esponsibility with respect to the automation safety and correct operation when other supplier s components are used Only use original parts for any maintenance or repair operation Do not modify the automation components unless explicitly authorized by the factory Instruct the product user about the control systems provided and the manual opening operation in case of emergency Do not allow persons or children to remain in the automation operation area Keep radio control or other control devices out of children s reach in order to avoid unintentional automation activation The user must avoid any attempt to carry out work or repair on the automation system and always request the assistance of qualified personnel Anything which is not expressly provided for in the present instructions is not allowed Installation must be carried out using the safety devices and controls prescribed by the EN 12978 Standard Important Safety Instructions A WARNING To reduce the risk of injury or death 1 READ AND FOLLOW ALL INSTRUCTIONS 2 Never let children operate or play with gate controls Keep the remote control away from children 3 Always keep people and objects away from the gate NO PERSON SHOULD CROSS THE PATH OF THE MOVING GATE 4 Test the gate operator monthly The gate MUST reverse on contact with a rigid object or stop when an object activates the non contact sensors After adjusting the force or the limit of travel
14. far away from the operator Try it again closer 3 Remote control is not suitable for receiver After making sure the codes are correct erase remote controls and then re program the codes in the device 4 Replace the control board or reverse position Gate open or close but stop in mid travel before reaching the fully limit 1 Check that the clutch is adjusted properly and is not slipping 2 The opening force or closing force is adjusted too small Turn the Potentiometer A to increase the force 3 Disconnect the gate from the gate operator and check that the gate slides freely without any binding 4 Replace the control board return The gate opens but stops and will not 1 Please note the two magnet brackets fixed plate are different one is higher and another is lower Please try to exchange the two brackets position 16 2 Please try to exchange the limit switch wires CL close and OP open 3 Maybe the magnet position was installed in the middle so it inducts both Switches Adjust the magnet higher or lower The gate can open but fails to close 1 Photocell is obstructed Remove obstruction 2 The limit switch is failed Use a jumper wire to short terminal 4 with terminal 3 and 5 and then use a keying device to operate the operator replace the higher limit switch if the motor couldn t run in clockwise direction and replace the lower limit switch if the motor couldn t
15. h section for standard package you can order extra rack from dealer if necessary 2 Put one end of rack section on the gear of operator as a temporary support Make rack level and mark the rack s mounting holes four holes for light duty or six holes for heavy duty on the gate 3 Fit the rack by self threading screws This kind of plastic rack is quieter and allows height adjustments to be made even after it has been fixed Please keep 1 0mm space between the rack and the gear to avoid the weight of the gate leaf effect on the operator alm a Higher Magnet Component Magnet Bracket 2 pca y Se DW Hex Bolt MBxTU 4 pos Piain Washer c B 4 pcs Spring Wahser T 8 4 pcs Hex Mut MB 4 pcs M _ Lower Magnet Component Plastic rack reinforced with steel 10 B Fit the galvanized steel rack 1 Start with gate in closed position 2 There are four sections of steel rack which is one meter length each section for standard package you can order extra rack from dealer if necessary 2 Put one end of rack section on the gear of operator as a temporary support Make rack level and mark the rack s mounting holes three holes on the gate 3 Weld the rack nut on the gate as mark and connect the rack to the gate using the bolt provided Before weld please keep 1 0mm space between the rack and the gear to avoid the weight of the gate leaf effect on the operator Magnet Bracket 2 pcs Hig
16. her Magnet Componert gt Lower Magnet Hax Bolt MB TO 14 ncs Component Plain Washer 73 4 ncs spring Wahser d ncs Hex Mui M8 dd ncs Galvanized Steel Rack Welding 1 f Rack Nu T EN Batt as i Washer ri i Gate Operator A E i j n w d S me AE a S S E E IU m y Concrete Pad Important Check that the rack teeth must engage the gear teeth throughout their full thickness If not adjust the position of the operator or and place a few shims between the rack and gate 4 Manually slide the gate leaf to ensure the rack is proper on the gear of operator weld the second nut 5 Repeat same steps of first rack section to install the rest rack sections until proper length is reached 6 Cut away any excess of the rack Note rack length must be longer than actual travel of the gate to accommodate limit switch brackets on each gate side 7 Thoroughly fasten the four nuts as well as spring washers onto anchor bolts tightly enabling the operator is firmly secured on the concrete pad during the whole gate travel Installation of the Limit Switch Before install limit switch make sure the gate operator is put in manual operation the clutch connected with gear shaft is disengaged and the mains power supply is disconnected Position the two Magnet Components approximately on the gate and move the gate by hand to fix them in place Fit magnets bracket Push the gate fu
17. lly closed by hand Locate and install the magnet bracket so that the operator will stop at the desired close position when the close limit switch approaches it 11 Push the gate fully open by hand Locate and install the magnet bracket so that the operator will stop at the desired open position when the open limit switch approaches it The higher magnet component must be installed at left side and lower magnet component must be installed at right side from the view inside of property Finally adjust the magnet to the proper position by moving the gate with the motor The magnet should be 39 59 away from the magnetic limit switch If it is too far away the switch will fail to work The distance between the magnet and the operator should be 1 2 12mm with the operator cover on Adjust the position of the magnet until the positions of the opening and closing meet the requirement Connecting Of The Control Board CONTROL BOARD 3 153 CIJE EIDE ries GG 3 9 G3 eS Solar Pans LM CSI Dril Swilthas Battery LM 323 Alam Lan L nii Be Ernler Bprener um mith wen rel Tie DEREN Bs A ipii pii dim it halogat EMTOZ 1 Taai i MATTER E E E a Fus Buhan LAT A5 Wired Keypad LM TOR M Loco Delecior LMi5d 12 1 Motor The YELLOW wire of the motor should be connected into the 1 terminal The RED wire of the motor should be connected into the 2 terminal 2 Limit Swit
18. member that cable conduits have to pass through the hole in the base plate 3 Pour concrete and before it starts to harden check that it is parallel to the gate leaf and perfectly level 4 The four anchor bolts must be set into the concrete when it is poured make sure the position of anchor bolts was placed according to the position of mounting holes on the base plate before concrete become harden 5 Mount the base plate to the concrete Pad 6 Place the operator onto base plate Check that it is perfectly parallel to the gate leaf and then screw the four bolts and washers supplied It s only temporary installation Further adjustment will be required when install the rack Manual Operation The operator should be put in the manual emergency release position before fitting the rack installing the 9 operator and limit switch The process is as follows 1 Take of the rubber stopple 2 Insert the Release Key provided and turn it in counter clockwise 180 to disengage the clutch between the gear shaft and power output Now the operator is in the manual operation Fit the Rack There are two kinds of rack available as per buyer s option which are steel reinforced plastic rack and galvanized steel rack The galvanized steel rack is usually used for the heavy duty gate A Fit the plastic rack reinforced with steel 1 Start with gate in closed position 2 There are four sections of plastic rack which is one meter length eac
19. metimes Note 2 Always check the gate reversing function every each time of control board set or restart after power off How to learn or erase the remote REM LED PYAR LED Learn the remote Press and release the learn button the REM LED light will be on then press the key in the remote twice Gontal Bazar A fixo um e Lean Bulpi in 2 seconds the REM LED light will flash for 4 t seconds Now the remote has been learnt successfully e Erase all the remote codes Press and hold the learn button until the REM LED light is off Now all remote codes have been erased How to use the remote to control the operator Koi A were Kay amp Key A is used to operate the operator to work alternately open stop close stop open When the Midway Mode function is enabled Key B is used to achieve the Midway Mode function open the gate for the pre setting time When the Midway Mode function is disabled the operator works alternately open stop close stop open by pressing Key B 15 Troubleshooting Have a multimeter to check voltage and continuity Use caution when checking high voltage terminals Symptom Possible Solution s Power LED is OFF Operator will not run 1 Check if the voltage at high voltage terminal is 120 230 VAC If the voltage measures 0 check the damaged power cable 2 Check if the output voltage of the transformer is 24VAC If the voltage measures 0 the transformer may be overhe
20. mits radio frequency RF signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures natural landscaping or similar obstruction A wireless contact sensor shall function under the intended end use conditions 6 One or more contact sensors shall be located on the inside and outside leading edge of a sliding gate Additionally if the bottom edge of a sliding gate is greater than 6 inches 152 mm above the ground at any point in its arc of travel one or more contact sensors shall be located on the bottom edge 7 One or more contact sensors shall be located at the bottom edge of a vertical barrier arm Preparation for Installation Before proceeding to your operator installation check if your gate structure is in accordance with the current standards especially as follows The gate sliding track is linear and horizontal and the wheels are suitable the gate should be mounted and moving freely Check that the structure is sufficiently strong and rigid and that its dimensions and weights conform to those listed in the specifications table of this document Make sure that the gate is plumb and level The fence posts must be mounted in concrete The gate does not bind or drag on the ground The gate manual operation can be carried out smoothly along its entire run and there is no excessive side slipping The opening and closing g
21. ning time of the operator in midway mode is 2 4 6 seconds N DIP Switch 23 45 Fine adjust the soft stop period of the motor DIP Switch 3 ON 1 Second OFF 0 DIP Switch 4 ON 2 Seconds OFF 0 DIP Switch 5 ON 4 Seconds OFF 0 NOTE Every time you restart the gate operator after power off you should use the access control device such as remote push button and etc to operate the gate operator to run for a complete opening cycle and a complete closing cycle to get the full opening time and the full closing time the motor would run with 5096 rated speed for DSR DSC 1000 and 100 rated speed for DSR DSC 600 during the first two cycles You would achieve the soft stop in your next opening closing cycle Factory default soft stop time is 2 Seconds You can turn the DIP switches on off to fine adjust the soft stop time to meet your actual needs iza45676 gt The soft stop period of the motor is 1 2 3 seconds on DIP Switch 6 7 Auto close time of the gate operator DIP Switch 6 ON 30 Seconds OFF 0 DIP Switch 7 ON 60 Seconds OFF 0 NOTE The auto close function would be disabled if both DIP switches are turned to off factory default setting us 8 Ai AR gt Auto close time of the gate operator is 30 60 90 seconds On DIP Switch 8 Left Right open ON Right open For gate to open toward right OFF Left open factory default setting For gate and close toward left
22. run in counter clockwise direction 3 Replace the control board Maintenance Every six months check the following items for proper operation of the unit Lubricate shafts and sprockets Keep operator clean at all times Check and tighten anchors bolts Check for loose or corroded wire Ensure the operator is well earthed and correctly terminated Always check the Stop Reverse in case of obstruction function when performing any maintenance If this function can t be made operable remove this operator from service until the cause of the malfunction is identified and corrected According to Waste of Electrical and Electronic Equipment WEEE directive WEEE should be separately collected and treated If at any time in future you need to dispose of this product please do NOT dispose of this product with household Please send this product to WEEE collecting points where available LockMaster ALL Rights Reserved 17
23. to open toward left and close toward right 2 Potentiometers The potentiometer A is used to adjust the stall force of the gate operator Don t use the Potentiometer B unless some occasional case happed such as entrapment protection fails Both two potentiometers of 14 factory default force have been set to at 15 00 o clock Turn the potentiometer clockwise to increase the stall force Turn the potentiometer counter clockwise to decrease the stall force Potentiomeler 4 Poleantiometer B Contral Board Test the reversing sensitivity For the sake of safety it is very important to test the reversing sensitivity as soon as the control board set is finished The reversing sensitivity adjustment is inverse correlation with stall force adjustment in potentiometer A In other word the stall force level is higher the reversing sensitivity level is lower Put an immobile object along the gate path and then operate the gate to strike it during the open and close cycles The gate must reverse as soon as object is struck with it If the gate doesn t reverse please increase the reversing sensitivity by turning the potentiometer in counter clockwise direction Turning the stall force potentiometer toward to MIN position to increase the reversing sensitivity Note 1 If the sensitivity setting is too higher the gate will stop or reverses very easy by itself while there is little obstruction or resistance such as strong wind or heavy snow so
Download Pdf Manuals
Related Search