STEYR Control Center Configuration User Manual
Contents
1. Box No 4 H england Picture 10 configurable data of an output When selecting an output in the route window you can configure data as shown in the above picture Configurable output data e Auto off time duration after which time an active output is switched off automatically Attention the unit of this value is 1 10 seconds e g a value of 100 means ten seconds Allowed values any positive integer Zero means no automatic switch off e Push button when checked the button in the I O Box view of the SCC software is a push button That means that an output is only switched on when the button is pressed in the SCC software When Push button is not checked the output is like a normal switch Z001075 0 04 081211_MAD Page 16 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS Gi EG o Box NMo 3 Changing the position of an output O Da Right click the output element in the route window from which ES you want change the position in the following context menu a oe A AA select Move up or Move Down Repeat this step until the ii output is placed correctly RBE fA 7 IO Box Mo 4 The top position is the top left button in the STEYR CONTROL CENTER one below top is for top right button 3 from top is bottom left and bottom position is the bottom right button on the display Renaming an output Right click the output element in the route window of which you want2. The lowest or highest scale value of the calibration values may not be the same as the scale min or max It s also possible to start and end with the calibration values somewhere in the middle of the sensors scale bandwidth In the picture above you see a sensor with the behaviour when the resistance of the sensors goes up the scale value goes up too There are also sensors like temperature sensors NTC s with the opposite behaviour when the resistance goes up the scale value falls see the picture bellow Calibration alues X Calibration values 5 23 000000 4200 29 000000 540 90 000000 Move Up Insert Delete Move down Clear all Picture 14 raising resistance falling scale value Attention when defining calibration values you must always define them in the right order Z001075 0 04 081211_MAD Page 21 of 24 STEYR CONTROL CENTER Configuration software users manual Changing the position of a sensor Ei Sensors Move Up Right click the sensor element in the route window of which E you want change the position in the following context menu ce select Move up or Move Down Repeat this step until the sland Delete Sensor sensor is placed correctly ues The top position is the top middle instrument in the STEYR CONTROL CENTER one below top is for the bottom left instrument 3 from top is bottom middle and bottom position is the bottom right instrument on the
3. change the name in the following context menu select Rename output The name of an output is equal to the label of the corresponding button in the SCC software Adding a new sensor to an I O Box ii STEYR Control Center Configuration File Options wiew Help H D austria E ni STEYR ic STEY Picture 11 Add a new sensor Right click the Sensors folder of the I O Box where you want add a new sensor in the route window in the following context menu select Add new sensor and input a name for it After confirming the Enter name input box with OK the new sensor will be added with default configuration settings Maximally four sensors are permitted Z001075 0 04 081211_MAD Page 17 of 24 eX STEYR CONTROL CENTER STEYRMOTORS K Configuration software users manual Configure a sensor Ae STEYR Control Center Configuration ioj x File Options View Help STEYR Control Centers H E austria Ba Spey Me Pressure sensor i A Default O Box i self defined sensor i BO I O Boxes B YWO Box No 3 Filter Se ae Outputs A sensors Sensor max value 1 10 Ohmi LEAU ol Fuel AFT Sensor min value 1 10 Ohmi ae 25 Scale unit BILGE ALARM Scale max value EE 1O Box No 4 fe Bar E HG england Scale min value I Enable upper red region nable high alarm eee 25 I Enable high al Upper red region B Engine must rum I Enable lower red region 0 T Enable
4. l l l ASTER Control Center Configuration e About SCCWinConfig shows version information Fie options wiew rey a Abat sccwincentia Toolbar e Ei sameas menu File gt Save Z001075 0 04 081211_MAD Page 6 of 24 STEYR CONTROL CENTER Configuration software users manual a I Ta STEYRMOTORS j MELAN INNOVATION WITH LIG HTHEGI nA Route window BE OuRSTEYR Control Centers o HG austria Toa Symbols fe Default I Box l oo Main element for the STEYR CONTROL EEE YO Box No 3 CENTER Pool EMS S ha oe NAY LT pa Grouping folder BL ER BP Sse Be amp STEYR CONTROL CENTER EH Sensors Fuel AFT 1 O Box A G PRESS A G TEMP l wf BILGE ALARM gt ane DE TfO Box No 4 MC england I lt Sensor input H Connected SCC HE Default 1O Box eS Ti Boxes E 2 Holyhead E Plymouth Relay output Via ActiveSync connected SCC Picture 2 route window Under the main element STEYR Control Centers it s possible to create grouping folders and STEYR CONTROL CENTERS Grouping folders are useful to get a structure in the configured SCCs Use these folders for example for customers a boat configuration places The second main element Connected SCC is only available if an SCC is connected via ActiveSync to the computer this has the same functionality as an SCC which is stored in the pool Z001075 0 04 081211_MAD Page 7 of 24 STEYR CONTROL CENTER Configuration software us
5. EYR CONTROL CENTER to the computer This is necessary to access and change data from an SCC If ActiveSync is already installed on the computer and a connection to an SCC is possible then you don t have to install ActiveSync again How to check if a connection via ActiveSync between an SCC and the computer is possible In the ActiveSync connection settings enable the USB connections power up the SCC and connect it with the USB cable to a free USB port of the computer The connection wil be established automatically Confirm the question if you want to set up a partnership with the device with no a guest connection is enough to configure the SCC STEYR CONTROL CENTER Configuration Software For installation simply run the setup program InstallSCCWinConfig msi from the setup CD or download the newest version from the internet ATTENTION uninstall any previous installed version before installing a new one Z001075 0 04 081211_MAD Page 4 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS Application interface Main window M e n u a STEYR Control Center Configuration gt File Options View Help Toobar es DB austria a boat xy FO aipa STEYR CONTROL CENTER Configuration PT Outputs c STEYRMOTORS GmbH Steyr Austria BILGE ALARM E L 1 0 Box No 4 H O england E E Connected SCC Default 1 0 Box 10 Boxes E L Holyhead D Outputs gt ER BP gt
6. JET BP A NAY LT gt IR FLD H O Sensors E L Plymouth Status bar Picture 1 application window Menu application menu Toolbar with the save button changes are stored in the STEYR CONTROL CENTER Pool on the hard drive or the connected SCC is updated Route window all stored SCCs and the connected SCC are listed in this area Data window depending on which item is selected in the route window all configurable values are shown in this area Status bar in this line is a short description of selected menu or context menu entries shown Z001075 0 04 081211_MAD Page 5 of 24 STEYR CONTROL CENTER Configuration software users manual Application menu Menu File e Save Ctri S saves all changes onto the hard drive if data 0 STEYR Control Center in the SCC pool are changed or transfers changes to the Selene lew bile connected SCC if changes were made on the connected SCC aes ems e Exit quits the application if changes were made the application will ask to save them Exit Menu Option JH STEYR Control Center Configu e Set path of SCC pool sets the path on the hard Sje Options view Help drive where all SCC and grouping folders should be Set Path of SCC Pool saved Menu View STEYR Control Center Confi e Toolbar shows or hides the toolbar File Options view Help e Status Bar shows or hides the status bar Toolbar w Status Bar Menu Help l l
7. STEYR CONTROL CENTER Configuration software users manual jii STEYR Control Center Configuration E O x File Options wiew Help l 4 austria o BA boat xy 7 z ek yoso STEYR CONTROL CENTER Configuration l a ED Outputs c STEYRMOTORS GmbH Steyr Austria ES Sensors 3 BILGE ALARM ok Be TO Box No 4 H E england Fe Connected SCC HE Default 1O Box Ee LO Boxes E Holyhead 2 EM Outputs H E Sensors nEs Plymouth YR Control Centers Z001075 0 04 081211_MAD Page 1 of 24 STEYR CONTROL CENTER Configuration software users manual PUD OT EVAO S iE yecnswnanauansnesesasunebaun ase besnewnaneuanenevasaneieeeatsUereest E 3 DUTT OCT ON E E sca sccansonsaessassec acsoseecas 3 DYES TOON soars Pater cts ais E O 4 Microsol A COVES VNC spini 4 STEYR CONTROL CENTER Configuration Software ccsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssess 4 APPC ALON OI OCC eg ssvagcoccccat ctu cte sas cecsanseese E E EE 5 IVAN Wy INN WY sass casein ea seas cesses E van see bes eens cuteeuasees ue ceneuyenwsnets euceeenweeusceseuceusayeessscesszceuenvesess 5 ApphcaNon MeNi ssiri a a 6 Route WO Wy sora rscsesceandeecateastaaccusanenenscssaceuedauasatesutacenecansnenecsie ates auscetessescauesavscenecstecstelavsnetecsbecsberansnenecsuecaueraussenecsnecenc 7 How to work with the application 2 vss ss teucovesaasceschvausescessvensshecucousss cus vous scecauedsaxecscbececesseasssesegeusaveec
8. TEYR CONTROL CENTER and input a name for it After confirming the Enter name input box with OK the new SCC will be added with default configuration settings ji STEYR Control Center Configuration _ O x Fie Options View Help Ma STEYR Control Centers H austria Ff boot 5 een STEYR Control Center Configuration E birmingham a mm be Mew Folder ae a ae New STEYR Control Center Paste STEYR Control Genter EYRMOTORS GmbH Steyr Austria Delete Folder Rename Folder Create a new STEYR Control Center MUM E Picture 3 create a new SCC Z001075 0 04 081211_MAD Page 10 of 24 STEYR CONTROL CENTER Configuration software users manual y aN STEYRMOTORS Configure a STEYR CONTROL CENTER aH STEYR Control Center Configuration Joj x File Options wiew Help 1 4 STEYR Control Centers a austria HE boat xy Time zone UTE 2 Hours FMS england Manual tank litre H birmingham Gear ratio 0 london Tank volume hA Propellor pitch fo a mee j Alarm level J 1 gt EHE le eS manchester H Connected SCC Temperature Pressure Volume i kmh Celsius C Bar Litre C knots Fahrenheit F PSI Gallons C mph C kPa CAN behavior 0 Master C Slave Picture 4 configurable data of an SCC When selecting an SCC in the route window you can configure data as shown in the above picture Configurable common SCC data
9. ck the I O Boxes folder of the STEYR CONTROL CENTER where you want add a new I O Box in the route window in the following context menu select Add new I O Box and input a name for it After confirming the Enter name input box with OK the new I O Box will be added with default configuration settings from the Default I O Box After this enter a correct serial number for the new I O Box because zero is not allowed Configure a O Box STEYR Control Center Configuration x File Options View Help STEYR Control Centers eM aa Serial number 200004 HA book xy aE i Default If 0 Box con pa ES T O Boxes Priority ee Picture 7 configurable data of an I O Box When selecting an I O Box in the route window you can configure data as shown in the above picture Z001075 0 04 081211_MAD Page 13 of 24 STEYR CONTROL CENTER Configuration software users manual a i alias j iMag aa TEA INNOVATION WITH LIGHTAES ii Configurable common l O Box data e Serial number serial number of the I O Box for which this configuration is valid This number is very important because the STEYR CONTROL CENTER recognizes the connected I O Boxes through there serial numbers According to the serial number the SCC knows which configuration it should take to calculate and show data from the I O Box The configuration of an I O Box is always stored on the SCC and not in the I O Box itself The only thing which
10. cscceccccccscesccecccscescesees 13 Comoe TIO BO eee E EE caianene atone mova a E E E T sanded 13 Configurable common O BOX data ccccccccccccssssssssssssseeeeeeeeeeeeeeeeeaaeessesseeeeeeeeeeeeeeeeeeeeeeaaaeessssseseeeeeeeeeeaqageaggesases 14 Elements below an I O Box element in the route window cccccccccssseeseccceeeceesseeeccceecsaaeseeecceeessaaeesececeeeeaaaaeeeess 14 Adding a new output toan VO BOX gi cicatcccescczenciecibccecsnctencccebiavenseetensy an tends sabiscanseepencvech Eana Ea aan aera ninan 15 Connora COU UG ALA eei e E EEEE EEE EEE EE 16 Changing the position Of an OULPUL ccccccccccccccccceeeeeaasseseeseseeeeeeeeeeeeeeeeeseeseeeeseeeeeeeeeeeeeeeeeaaaaeaesessseeeseeeseeeeeeeaaags 17 Renaming an OU csc cancasaacanaceneneceteon ecasagaamenaseheccanepacaeoasaieaeaenananeeseehaneumaeus aadesdapaansndacnemnest nic sanpevacdanad eaeauasocdgesecuanct 17 Adding a new sensor to an T OB ON ssecsicsiscctccetecctncsncvetbesesuctecsvacetacndecctinesueuetbenesuctbestecetacndeccteesusteticbesustecstecetncadescteess 17 Cona a GOMS OF e A T T E A E 18 Configurable sensor dali seroren OOE EEEa EEDA SER Ea O ORO AEE 18 Sensor Ype descrip IOI co cer cisrcenctcanssnaveesaaittauneaememaecuaasoatasnsuinehacestalovenesecsnspusseuansteind OE a EEEa EEA EREA 19 Canbron ValS eoin Or A E A OEE O AE AOA 20 Changing the position of a SNS OF vicaisccacassadnanssiuseavanandeddwetetessacs whinxnsihaisaheannadnstnebodeadaaixtinassnhadnpecanabest
11. cusnscss sesoutsseresnehdes euceessee 8 DEE VI CON PROUT CE INTER pool ses 8 What is configurable of a STEYR CONTROL CENTER ccccccccssscccccsccccccccesesccsccccsececcccsccecceccscesscecesecccccces 8 Handling with the user interface ssiccctestcececescasccceviceascesvenceeseccucnessesesencetesecoceueevasesdesossescveven ceceectecnsaesossnteseueseeeescscnerensee 8 Saving chanacd data mi ihe SCC OOM aac eseserass casas csceeusvenstewesecesecseveeasuouesssseeuesnasuoeues taasuveeatesnacaiegeseseasveuwscceaeuveeatioes 9 Saving changed data of the Connected SCC eiisteecetenceeenscteticeerises atest aces 9 Conjigure STEYR CONTROL CEN TE vrccspccorcctaccoscespteaxtisascerscapecance asaensessseanecensienscatesancebaaconccassearscehuserscatesoncebsniotaced 10 PCG NG MEW CV OU INE TONG 0 s sisien EEEE EEEE EEEE REEE ENAERE REEE 10 Adding a new STEYR CONTROL CENTER svssesssssssssscsssscensenesdnnnessessacseessvevasoncnacenccdeswedeeteusanesdvocatoosnnsenecdvavsssssevses 10 Conneurea STEYR CONTROLCENTER vac sccansoictenezassestneanns ce oaie a EEEN ENaC iei l1 Confieurable common SCC a lac acace ceacscaezacascdsiesccustenincaadustcenseaieabecaneeceucuacnsoueanas cercaadncbnrone scsatusamibacaneedcersesaremeeuaes 11 Elements below an SCC element in the route WINdOW cc ceeccccccccsseeseeeccceecaaesseeccceeseaaeeeecceeesaueeseeecesessaaaeseeeeeeeeas 12 Adding a new I O Box to a STEYR CONTROL CENTER ccccccsscssccsccccccccccescscccceccscese
12. display Renaming a sensor Right click the sensor element in the route window of which you want change the name in the following context menu select Rename sensor The name of a sensor is equal to the label of the corresponding instrument in the SCC software Z001075 0 04 081211_MAD Page 22 of 24 STEYR CONTROL CENTER Configuration software users manual a ape i Cle aa TEA INNOVATION WITH LIGHTAEE 5 Working with the Connected SCC Change the connected SCC directly When a STEYR CONTROL CENTER is connected to the host computer via ActiveSync you see the element Connected SC jn the route window You can configure the connected SCC like a normal SCC which is saved in the pool When you are finished with the configuration don t forget to save menu File gt Save your work When disconnecting the SCC from the host computer without saving you will lose all your configuration changes After saving changes of the connected SCC you have to perform a restart of the SCC to take effect the new configuration Transfer the configuration of an SCC in the pool onto the connected SCC After you have finished the configuration of SCCs in the SCC pool you may want to transfer the settings from an SCC inside the pool onto the connected SCC This is easily done by selecting with the right mouse button on the relevant SCC in the pool and selecting in the following context menu Transfer STEYR CONTROL CENTER The e
13. e Time zone when a GPS sensor is connected to the STEYR CONTROL CENTER then the time zone must be configured because the received GPS time is UTC time Allowed values all values from the drop down list e Gear ratio to calculate the theoretical speed and the corresponding slip value this value is required i e 2 1 Allowed values any positive decimal number e Propeller pitch this value is needed for the same reason as the gear ratio Allowed values any positive decimal number i e 20 e Tank volume tank volume of the manual tank Allowed values any positive integer e Alarm level level when the SCC should show a warning if the actual contents of the manual tank falls below this threshold Z001075 0 04 081211_MAD Page 11 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS Allowed values any positive integer and 1 If 1 then no alarm level is configured e Units unit which is shown for speed temperature pressure or volume values in the SCC software Allowed values any selection e CAN behaviour it is possible to connect more than one SCC on the same CAN line at different places e g to view engine or sensor data or to switch an I O Box relay output from different locations on a boat At start up the Master SCC initializes the I O Boxes and Slave SCCs with important values for the CAN communication and this is only allowed from just one Master SCC So for a functional commun
14. ers manual STEYRMOTORS How to work with the application STEYR CONTROL CENTER pool The SCC pool is a directory on the hard drive or a mounted network share The pool consists of grouping folders and configured STEYR CONTROL CENTERs Grouping folders can contain other grouping folders STEYR CONTROL CENTERs or both By default the directory for the SCC pool is SCCPool under the installation path of the SCCWinConfig software You can change the SCC pool directory with the menu item Options gt Set path of SCC pool What is configurable of a STEYR CONTROL CENTER Time zone Gear ratio Propeller pitch Volume and alarm level of manual tank Unit values CAN behaviour Default I O Box I O Boxes Handling with the user interface Creating deleting renaming copying or transferring objects grouping folders SCCs I O Boxes outputs or sensors is done over the context menu when clicking with the right mouse button on an element in the route window When adding an object the object is always added as a sub element from the selected element in the route window To change data of an object SCCs I O Boxes outputs or sensors select the corresponding element in the route window After this all configurable data are shown in the data window I mportant when entering fraction of numbers always use the decimal point e g 15 7 Z001075 0 04 081211_MAD Page 8 of 24 STEYR CONTROL CENTER Configuration s
15. ication between the engine SCCs and I O Boxes it s necessary to have just one Master SCC and any number zero is also possible of Slave SCCs Allowed values see description above Elements below an SCC element in the route window ai STEYR Control Center Configuration File Options View Help Time zone OUTE 2 Hours a Default 1 O Box H 1fo Boxes Manual bank litre vy G tic 2 0 Ge XVZ BOX ear ratio T Tank volume TV Outputs Propellor pitch B 3 HORI g R Alarm level 10 mlotecoe Picture 5 elements below SCC element e Default I O Box Each SCC has a Default I O Box member which can be configured like a normal I O Box except for the serial number This configuration will be used if an SCC recognizes a new or unknown I O Box SCC s recognize the I O Boxes by there serial number Recommended configuration when using only one I O Box configure the Default I O Box equal to the connected one The advantage is when you change the I O Box due to a defect you don t have to set up the new one e I O Boxes The I O Boxes folder can contain an unlimited number of configured I O Boxes which the STEYR CONTROL CENTER knows Z001075 0 04 081211_MAD Page 12 of 24 STEYR CONTROL CENTER Configuration software users manual H austria book x ae saad IO Box S T Y R Co n ele itlenstereert aur c STEYRM Picture 6 Add a new I O Box Right cli
16. is permanently programmed into the I O Box is its serial number Allowed values any positive integer except zero e Priority when more than one I O Box is connected to the STEYR CONTROL CENTER the priority defines the order of the recognized I O Boxes in the I O Box view of the SCC software Null means the highest priority and 255 the lowest The order is random if two ore more I O Boxes have the same priority Allowed values any slider position Elements below an I O Box element in the route window ap STEYR Control Center Configuration a iol X File Options View Help H austria ee at book xy E 2 Default 1 0 Box Fl O Boxes Serial number 3 Priority 0 j fe wox hq EE Outputs B Sensors oof Fuel AFT GPRESS BILGE ALARM Oo E 110 Box No 4 3 england Picture 8 elements of an I O Box Z001075 0 04 081211_MAD Page 14 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS KD INNOVATION WITH LIGHTMES a e Outputs The Outputs folder contains the configured relay outputs of an I O Box The order of the outputs in the route window is important because it represents the pinning on the I O Box output connector The first output in the route is the first relay place on the output connector Pin 1 and Pin 12 of the I O Box the second output is the second relay place etc for a connector description of the I O Box see the SCC technical documentatio
17. is switched off When the sensor switch is opened the backlight is turned on again e Common sensor Sensors with no special type Calibration values Calibration values are necessary to define non linear sensors When defining sensors without any calibration values then the scale value is calculated with the linear interpolation method between the sensor min and max value Calibration values are always two values the resistance value of the sensor and the corresponding scale value This pair of values defines a point in the sensor curve A sensor can have an unlimited number of calibration values Attention when defining a calibration value pair the resistance value must be given in 1 10 ohm Z001075 0 04 081211_MAD Page 20 of 24 STEYR CONTROL CENTER Configuration software users manual Calibration alues x Calibration values Ohm 1 10 Scale value l Cancel o 2 Q00000 710 3 000000 900 4 000000 caren 1070 5 000000 Ea e 1240 6 000000 1400 7 000000 Insert 1560 5 000000 1630 8 500000 Delete 1700 9 000000 1840 10 000000 Move down Clear all Picture 13 calibration values input dialog The order of the values listed in the calibration values dialog is very important the calibration value pair with the lowest scale value has to be at the top at the bottom of the list the value pair with the highest scale value The list is ordered from the lowest scale value to the highest scale value
18. low alarm i Engine must rum Calibration values 6 value s sek Lower red region Picture 12 configurable data of a sensor When selecting a sensor in the route window you can configure data as shown in the above picture Configurable sensor data e Sensor type see sensor type description below e Sensor in this drop down list you can find all predefined sensors of the selected sensor type When selecting any predefined sensor all data except the red region parts are filled out When selecting the self defined sensor entry from the drop down list it s possible to configure all values from the sensor yourself e Filter number of measured sensor values to calculate an average value This is useful for a sensor which has a huge fluctuation e g tank level sensors The average value is shown in the corresponding instrument in the I O Box view of the SCC software The I O Box measures and sends the sensor values approximately every second so a filter value from max five is recommended Allowed values any slider position Zero and one means no filter is used the sensor values are shown directly in SCC software Z001075 0 04 081211_MAD Page 18 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS e Sensor max value resistance of the sensor when it reaches the highest possible scale value Attention the unit of this value is 1 10 ohm e g a value of 1000 means 100 ohms Allowed va
19. lues positive integer 0 65535 e Sensor min value resistance of the sensor when it reaches the lowest possible scale value Attention the unit of this value is 1 10 ohm e g a value of 1000 means 100 ohms Allowed values any positive integer 0 65535 e Scale max value value which is shown in the instrument at the end of the scale Allowed values integer 999 999 e Scale min value value which is shown in the instrument at the start of the scale Allowed values integer 999 999 e Scale unit unit of the values Scale max value and Scale min value Attention this is not the unit which is shown for the instrument in the SCC software The instrument unit is configured in the common SCC settings The scale unit is needed for a conversion into the different shown units e Enable upper red region enables the possibility to configure an upper red region and a high alarm warning e Upper red region scale value at which the upper red region should start Allowed values interger value must be lower than Scale max value and greater than Scale min value e Enable high alarm if enabled a warning popup appears on the SCC when the sensor value is greater than the Upper red region value e Engine must run if enabled the high alarm warning appears only when the sensor value is greater than the Upper red region value and the engine is running e Enable lower red region enables the possibility to configure a lower
20. n e Sensors The Sensors folder contains the configured sensor inputs of an I O Box The order of the sensors in the route window is important because it represents the pinning on the I O Box sensor connector The first sensor in the route is the first sensor input place on the sensor connector Pin 1 and Pin 8 of the I O Box the second sensor is the second sensor input place etc for a connector description of the I O Box see the SCC technical documentation Adding a new output to an I O Box ay STEYR Control Center Configuration Fie Options wiew Help fe STEYR Control Centers H E austria fo f a ba TO Box S T Y F Bo TiO Boxes I a TO Box No 3 SORME c STE oo E N0 Box Mo england Picture 9 Add a new output Right click the Outputs folder of the I O Box where you want to add a new output in the route window in the following context menu select Add new output and enter a name for it After confirming the Enter name input box with OK the new output will be added with default configuration settings Maximally four outputs are permitted Z001075 0 04 081211_MAD Page 15 of 24 STEYR CONTROL CENTER Configuration software users manual 15 x File Options View Help STEYR Control Centers Er austria Elf book xy Auto off tine 1 10 sec T T Push button Ee Default 110 Box A TiO Boxes aj LO Box Wo 3 3 HS Sensors H TO
21. ntry Transfer STEYR CONTROL CENTER is only available if an SCC is connected to the host computer via ActiveSync AP STEYR Control Center Configuration File Options View Help File Options View Help OY STEYR Control Center Configuration H E austria Time zone Jur g A book xy Oi E amp A DeFault 1O Box Delete STEYR Control Center o D E 1O Boxes Gear ratio Rename STEYR Control Center Ae IO Box Mo 3 l E o ES Outputs Propellor pitch Transfer STEYR Control Center 3 3 Be Sensors fK Fuel AFT eal Units E Units 4 ooh G PRESS qJ in Speed ar G TEMP Speed 1 _AQ BILGE ALARM o 2 col BILGE ALARM p N DE 2 T O Box No 4 kmh 5 a GES i TO Box No 4 a e noe o knots i 2 a S o F Poa n Conn Copy connected STEYR Control Center H 1 9 Connected SCE Picture 15 Transfer to peace SCC and copy connected SCC Copying the connected SCC into the SCC pool To store the connected SCC inside the SCC pool right click the Connected SCC element in the route window and select Copy connected STEYR CONTROL CENTER Now right click a grouping folder or STEYR CONTROL CENTERs and select Paste STEYR CONTROL CENTER enter a name for the SCC and confirm the box with OK The configuration of the connected SCC is saved below the folder where you have selected Paste STEYR CONTROL CENTER Z001075 0 04 081211_MAD Page 23 of 24 STEYR CONTROL CENTER Configuration sof
22. oftware users manual STEYRMOTORS Saving changed data in the SCC pool After changes have been made the data must be saved e g with menu File gt Save before quitting the application to store the changes permanently in the pool Some changes are stored immediately in the pool without the need to save them explicitly these are e renaming a grouping folder or SCC e deleting a grouping folder or SCC e creating a new grouping folder or SCC e copying an SCC Saving changed data of the Connected SCC Each change is done temporary on the hard drive so you have to save your work e g with menu File gt Save before quitting the application or disconnecting the SCC from ActiveSync After saving you must restart the STEYR CONTROL CENTER to take effect of the new settings If you do not save the changed data and disconnect the SCC from ActiveSync or quit the application all changes will be lost Z001075 0 04 081211_MAD Page 9 of 24 STEYR CONTROL CENTER Configuration software users manual a STEYRMOTORS Configure STEYR CONTROL CENTERs Adding a new grouping folder Right click the STEYR CONTROL CENTERs element or another grouping folder in the route window in the following context menu select New Folder and input a name for it Adding a new STEYR CONTROL CENTER Right click the STEYR CONTROL CENTERs element or a grouping folder in the route window in the following context menu select New S
23. red region and a low alarm warning e Lower red region scale value at which the lower red region should end Allowed values interger value must be lower than Scale max value and greater than Scale min value e Enable low alarm if enabled a warning popup appears on the SCC when the sensor value is lower than the Lower red region value e Calibration values see Calibration values below Sensor type description Possbile sensor types are e Empty sensor place When Empty sensor place is selected then the corresponding sensor place in the I O Box view of the SCC software is empty This is needed when the sensor place on the I O Box connector is not used Z001075 0 04 081211_MAD Page 19 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS e Fuel sensor Fuel level sensor for tanks Sensors of this type can be selected as used tank sensor in the tank view of the SCC software e Temperature senor Temperature sensors e Pressure sensors Pressure sensors e Digital sensors Digital sensors are sensors which have only two states on and off like a switch The only thing you can configure with a digital sensors is a high alarm warning when the switch is closed null ohm or a low alarm warning when the switch is opened co ohm Predefined digital sensor Screen off mode If this sensor is selected and the corresponding sensor switch is closed then the display backlight of the SCC
24. tware users manual i STEYRMOTORS KD Wea INA OY A TIO WITH Lie EAE ot The About SCCWinConfig dialog To obtain version information of the application and the available predefined sensors select menu Help gt About SCCWinConfig About SCCWinConfig xX SCCWinContig version w1 05 Copyright 2 2006 Predefined sensor list version 2 Picture 16 About SCCWinConfig dialog Z001075 0 04 081211_MAD Page 24 of 24
25. uwbuliastadeshanesniaestoass 22 Renamine a S SOT asaan ae a a ee ae ea aanas 22 Working wilh ihe Connecied SGU esriviecsasizsncetiswiewsvosasseseaieieseasiesncedsnies cessnasseaiedesoasioanceieniawesssasseseaieiesessiesnceeoiewessia 23 Ihe Aboul SCCWinCon aaa sa oso ss Goa N N T 24 Z001075 0 04 081211_MAD Page 2 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS Abbreviations Controller Area Network Serial communication protocol I O Box Input Output box Optional box to connect sensors and to Switch loads STEYR CONTROL CENTER SCCWinConfig STEYR CONTROL CENTER this manual describes these software configuration software Introduction With the STEYR CONTROL CENTER Configuration software you can configure your STEYR CONTROL CENTERs The configuration of the SCCs can be changed and stored in the STEYR CONTROL CENTER Pool on the hard drive or it s possible to configure directly a via Active Sync to the host computer connected SCC For archive or duplicate purpose you can copy the whole configuration of a connected SCC into the STEYR CONTROL CENTER Pool The configuration of stored or changed SCCs in the STEYR CONTROL CENTER Pool can be transferred to the connected SCC Z001075 0 04 081211_MAD Page 3 of 24 STEYR CONTROL CENTER Configuration software users manual STEYRMOTORS Installation Microsoft ActiveSync You need to install Microsoft ActiveSync to connect a ST
Download Pdf Manuals
Related Search