e-one user manual
Contents
1. It is essential that the areas of the skin to be treated are freed of all hair by shaving wax cream electric epilator or any other method that plucks the hair should not be used The skin should be damp upon shaving to minimize the harsh effect of the razor e Rinse the skin thoroughly with water after shaving to remove any remaining cut hairs ISTEP 3 SWITCHING THE EOne ON AND ADJUSTING THE SETTINGS Reminder Icon definitions can be found on pages 14 and 15 e Plug the Onte mains lead in 3 beeps sound and 2 icons are displayed on the screen E gt One product icon top left On Off icon bottom left icon 15 p 15 The screen backlighting is not yet lit e Press the on off icon bottom left The backlighting comes on All icons are displayed The amp gt One internal test procedure begins and ends after a few seconds At the end of the test procedure the drop down text at the bottom of the screen proposes Epilation Press the validation icon bottom right icon 19 p 15 to access the clinical settings menu HAIR REMOVAL WITH THE EOne e Depilation settings SELECT YOUR PROFILE Male or female by pressing the relevant side of the body The profile selected remains displayed the other fades away SELECTING HAIR THICKNESS Once the profile is selected the 4 hair thickness icons are displayed from the finest hair on the left to the thickest hair on the right Press the desir2. inserted photo 28 Observation the cartridges are not symmetrical and must therefore be inserted in a certain way and care should be taken not to insert them the wrong way To guide you a red dot indicates the underside of the car tridge This must be placed to face the side of the epilator with the air vent Another red dot on the applicator shows you the direction both red dots should be on the same side Attention when inserting the cartridge care must be taken not to touch or snag the very fine metal wire shown in photo 29 e After having inserted the cartridge it must be ensured that it is in the right position it must be aligned with the tip of the fixed part of the applicator photo 39 If this is not the case if it overlaps by more than 2 mm CHANGING THE OPTIC CARTRIDGE this means the cartridge has been incorrectly inserted it must therefore be removed and you should check that the red dots are on the same side photo 28 the electrodes have not been twisted photo 31 If the electrodes have been twisted the Optic cartridge must not be inserted in the EOne This may cause serious damage to your Er One You must therefore return the damaged cartridge to us and order a new one e Check that the cartridge is firmly in place Precautions throughout cartridge replacement proce dure you must not touch The tube or its reflector photo 32 The tube electrodes photo 34 The short metal wi
3. then clean the filter red glass flat part using the dampened cloth Polish with the dry part of the cloth The spray must only be used when the E gt One has been unplugged and when the optical parts have cooled down If you are cleaning the E gt One immediately after use it must be ensured that the applicator fan has fully stopped before unplugging the base This enables the optical and other parts to cool down properly e the applicator touch screen never spray directly onto the touch screen Spray onto a dry cotton cloth then clean the screen using the dampened cloth Polish using the dry part of the cloth clean Made in France WUW E SWIN COM These patches are used to protect small areas that are not to be treated i e moles They must be placed after shaving and before application of the gel The designated areas can then be treated without having to worry about moles The patches should be removed at the end of the session patches Made in France These stencils can be used to mark out areas to be left untrea ted in order to keep hair in fun shapes in specific places see the templates on our website at www e swin com They are to be applied after shaving and gel application The gel helps hold the stencils in place The applicator is safe to use overlapping the edge of the stencils so as to form a clear outline of the Pr shape required Made in France FUN option Le 1er et le seul
4. appareil m dical d pilation au monde disponible pour une utilisation personnelle amp la maison Frais de por OFFERTS pour la France m tropolitaine Tout savoir sur E gt One en vid o a r Zi gt Actualit s gt T moignages Une peau durablement lisse pour cet t Marau Quand j ai appris l existence de l E One avec mon pouse R servez votre pack E gt One avant le 31 mars 2010 minuit et b n ficiez des frais de port gratuits Oltre gramatiommehe valable pour la France M topoitiane uniqverient iusas au 31 mars 2010 mingt Uanayaz et vener d couver tecna pe a de chez vous E piston dlectonque chez so Ala mason comme en nsttut de Dasut piston citntne mons chira que la laser Acheter benlateur umare pulse MAINTENANCE IBASE e Plastic parts All of the E gt One s plastic parts must be cleaned using a Clean cloth dampened with water only e Touch screen The screen must be cleaned using a cloth dampened with the clean spray never spray directly onto the touch I APPLICATOR e Mobile head Your E gt One will continue to perform well if the optical parts internal and external of the mobile head are cleaned with the Clean spray before and after each use Never spray directly onto the internal parts of the applicator screen e Mains lead Check that the mains lead is in perfect condition that it is not pinched or squashed and that there are no bare wires Cle
5. applied so as to snap on the appli UNS ST a lis Us el el E cis ee comes on no shot will be emitted optical parts to cool down fully cator head Shot emission can then be triggered by pressing Take care to stretch the skin in those areas in Store the E ne in a suitable place the button on the side of the applicator which it is finest to ensure that the glass part of the applicator tip light guide comes into contact with the skin and that hair is removed correctly Observation If you have sensitive skin do not use a from the treated area depilatory cream on the treated areas for one week after depilating with the EU ne Pressure must then be released for the applica tor to come away from the skin The applicator is then moved to an adjacent area The next shot may only be applied once the LED is green if the applicator is applied before the LED turns green no shot will be emitted STEP 5 e Press button 15 Observation Each time a shot is emitted the area epi lated is the area covered by the light guide tip 3 x 2 6 cm_ Upon releasing the pressure on the applicator a slight imprint can be seen in the gel enabling you to see where you are up to The glass surface light guide at the tip of the appli cator must be placed flat on the skin e You may unplug the E gt One from the mains once the fan has switched off after approximately 10 minutes e Clean the glass applicator head ligh
6. glass flat part and light guide To do this remove the mobile applicator head from the applicator body by pressing on both sides of the mobile head at the same time as shown below see photo 2 This enables visual access to the filter tube light guide and internal side The tube wall must be intact and must not be cracked The filter red glass flat part must be intact not split and must have a flat and regular surface It must be clean and dust free For E One to be more efficient it is recommended to clean the filter before each usage with the Clean spray provided upon purchase of the E gt OUne Any damaged filter due to bad maintenance will not be covered by the guarantee see the terms and conditions for spray usage in the appendix ISTEP 1 CHOOSE THE BEST TIME FOR USING THE E gt One If your usual depilation method is The razor You may use the E gt One straight away Depilatory cream You will only be able to use the E One one week after the last depilation Waxes electric epilator tweezers You will only be able to use the EOne three weeks after the last depilation Laser or flash lamp technology and other methods You will only be able to use the E One once regrowth has begun I STEP 2 PREPARING YOUR SKIN e Your skin should be clean and dry and cleansed of any cosmetic products e Do not apply any cream moisturizer oil or any other substance to the skin e Shave the area to be treated
7. E ONE User Manual HAIR REMOVAL WITH THE CHANGING THE OPTIC CARTRIDGE SOFTWARE OPTION Dear Customer Thank you for buying the E One Lifestyles are changing and the E One is a perfect example of this Professional and safe hair removal is now brought to you in the comfort and privacy of your own home give my own personal guarantee that each E Onre is manufactured to the highest standard and as you will see the E gt One is a remarkable product hope that you will be fully satisfied with your purchase and invite you to share your remarks on our company s official website Best regards ves ve Er e gt One creator E gt ONE PACK CONTENT 1 Stop marking plate 1 CLEAN optical spray 1 E gt Onke base details page 12 13 1 E gt Onkte applicator details page 12 13 1 Optic cartridge consumable included with your E gt One applicator 1 marking PEN for marking with sharpener 1 gel optical gel 1 Mask protective glasses 1 depilation diary 1 user manual its accessories Optic stop clean patches pen gel NOTE E Swin is exclusively authorised to sell the E gt One and A mask FUN etc on its website www e swin com 1 Patches adhesive patches ATTENTION DO NOT DISPOSE OF ANY OF THE ORIGINAL PACKAGING MATERIAL BOXES PROTECTION ETC The 2 year manufacturer s parts and labour guarantee is only valid if the item is returned in its original packa gi
8. an the lead using a cloth dampened with water only e Applicator body All plastic applicator parts must be cleaned using a clean cloth dampened with water only Take care not to drip any water into the lower shell air vent IBASE APPLICATOR CABLE This cable must be kept clean at all times and not show any visible damage It must never be folded or pinched If you have any doubts as to the cable s condition you must stop using your One immediately I BASE AND APPLICATOR AIR INLETS The applicator and the base are both ventilated Air vents are present on the lower part of the applicator and the lower and upper back parts of the base It must be ensured that these vents are clean and unobstructed STORAGE e Store your E gt One and accessories in their box e Store your E One at ambient temperature 40 maximum away from any sources of excessive humidity i e bathroom and vibrations i e on a washing machine e If the One is dropped or knocked it must be ensu red that all optical parts are intact e You must stop using the E gt One immediately if you notice any visible damage to the optical parts filter red glass flat part light guide tube etc STANDARDS I CERTIFICATION E SWIN SAS exclusive manufacturer of the E Once is ISO 9001 and ISO 13485 certified I COMPLIANCE E SWIN hereby declares that the E gt One is compliant with the essential requirements of Directive 93 42 EEC Ap
9. e ordered from our web site www e swin com via the Client corner and New Accessories Order sections We decline all liability for the use of cartridges and accessories provided by other manufacturers During use the E gt One must be placed on a flat surface and in a place where it is not likely to fall E SWIN SAS declines all liability for any damage resulting from improper use of the item or any use other than provided for in this user manual The E One comes with a pair of protective glasses mask these glasses must be worn throughout use Any other persons in the vicinity at the time of use of the E gt One must also wear a mask During operation the E Une must not come into contact with your hair the periocular region protected by the mask the E One must not be used for eye brow and eyelash removal for example clothing or other objects so as to pre vent any risk of injury blocking or deterioration The applicator tip must not be touching the mask during the shot Never use near aerosols or a heat source PRECAUTIONS FOR USE YOU SHOULD NOT USE THE E One e If you are pregnant or diabetic e To remove grey or red hair In particular individuals born with skin photo type and red hair In adulthood the fundamental orange colour may wane in these individuals however the hair s melanin structure retains the characteristics on which pulsed light depilation technology is ineffective e On very dark o
10. ed thickness the icon flashes SELECTING SKIN COLOUR Once the hair thickness has been selected 5 skin colour icons are displayed from the fairest skin on the left to the darkest skin on the right Very dark and black skin options are not UN 22120 as they are incompatible with the E One Press on the colour selected It will start to blink gt aid HAIR REMOVAL WITH THE EOne SETTING THE DESIRED INTENSITY Once the skin colour is selected the intensity gauge appears Icon II see page 15 is used to increase or decrease the shot intensitys a BR The intensity is set to low by default This value produces good results for the majority of users in optimum conditions of safety in 100 of cases Increasing the intensity will result in the following Enhanced results Reduction in the number of sessions required to obtain a lasting result Increased skin sensation upon application Increased risk of redness or even burns on highly pigmented skin dark skin after one session Icon I2 is used to confirm the intensity level see page 15 e Unlocking the safety system Once the previous settings are confirmed by icon l2 icons 2 3 4 5 and G as shown on page 14 begin to blink Important the darker the skin treated whether this is natural or through tanning the more it is This procedure recalls the basic safety guidelines recommended to set the gt no to a low intensity Water must not be projected o
11. ered confirm by pressing icon 19 You will then need to enter the second activation code and confirm it by pressing icon 19 If you have entered the wrong code an error message is displayed You must then enter the two activation codes again one after the other If the activation codes entered are correct the message codes accepted will appear on the screen You should then switch off your COnme and switch it back on again in order for the activation codes to be taken into account You may then use your E gt One normally the counter dis plays the number of shots available CHANGING THE OPTIC CARTRIDGE SOFTWARE OPTION ICHANGING THE OPTIC CARTRIDGE When the EOne is switched on the first menu proposed is the Depilation menu Next to this text is a set of icons SPECIAL PROCEDURES 16 which can be used to access the other sub menus of the embedded software via the Configuration menu e Personal identification code You can secure access to your E One by entering a personal identification number You may need to change the cartridge before the num ber of shots initially provided runs out due to a broken tube or a tube that no longer works for example This number is 0000 by default If you do not change your PIN number it will not be requested when the E gt One is switched on If however you change the default PIN 0000 you must enter the new PIN each time the E gt One is switched on When you have replaced
12. ing When blinking it indicates that certain com ponents have exceeded the permissible temperature The E One switches to standby mode automatically until normal temperature is reached again This icon warns that the projection of water on any part of the E gt One is strictly prohibited E Warning or precaution for use The following number icon shows which page of the manual should be consulted E Where a warning or precaution for use is displayed this icon shows which page of the manual should be consulted This icon indicates that the E One must not be used in certain physiological or medical contexts during pregnancy when taking photosensitizing medicine etc This icon indicates that the MASK must be worn at all times during use amp These icons are used to select male or female O These icons show 4 different hair thicknesses from the finest on the left to the thickest on the left E These icons represent 5 types of skin colour from the fairest on the left to the darkest on the right Black skin is not shown as the E One cannot be used on black skin THE E gt ONE BASE IS EQUIPPED WITH A TOUCH SCREEN Shot intensity gauge O These icons are used to increase or decrease the shot intensity Selections can be confirmed with icons 7 8 9 IO and ll Once the settings have been confirmed and the safety icons unlocked the E gt One is ready for use Pressing this ic
13. n the E One TheE One must not be used if taking photosensitizing medicine and the skin must be Sa A Bea 53 67 an a A Es The MASK must be worn throughout the session gt D A Always start with a test patch at the lowest setting default setting proposed by the Jme then increase the intensity level gradually by 1 point each time Apply a shot then wait for 5 minutes to evaluate the skin s reaction If no reaction occurs y you may then treat the entire area or increase the intensity by 1 point and re evaluate the reaction and di so forth N B the E Une will not emit a shot until all safety elements have been unlocked by pressing on each flashing icon I EXAMPLES l am a man with fair skin and want to epilate my armpits The following selections apply Male Fair skin 1st colour Thickest hair 4th thickness Intensity level gauge 1st level When the beard is flashed it could be painful so we recom mend that before flashing the gel should be stored in the fridge for 3 hours I am a woman with dark skin and want to epilate my arms The following selections apply Female Darkest skin 5th colour Hair 2nd thickness Intensity level gauge 1st level HAIR REMOVAL WITH THE EOne E QOne ty amp Y E Es Es ISTEP 4 APPLICATION e Circle the area to be treated using the DEN e Cover the small areas to be protected moles etc with the patche
14. nce the gel has been applied to the skin and exposed to the shots it must not be re used on another area The gel s optical characteristics are subject to change after treatment The gel is to be removed at the end of the session either in the shower or using a damp towel It should also be removed from the optical and mobile parts of the applicator using a slightly damp cloth and the clean spray Active components Menthylsothiazoline and Methylcholoroisothiazolinone MCI MI Their quantity in a ratio of 3 1 is 0 0008 Does not contain formal dehyde Keep away from light external use only Do not use on damaged burnt or infected skin gel Made in Europe The mask must be worn by all persons present at the time of shot emission It masks the area that should not be exposed to the treatment eyelashes eyebrows etc Made in China mask This plate is made from a shot resistant material It is used to protect any areas from unwanted treatment i e a tattoo The glass applicator tip light guide is safe to use overlapping the Stop and the skin Made in France stop See all our products on our website at The clean spray is used for the cleaning and maintenance of e the optical parts of the mobile applicator head external optical parts spray on directly then wipe with a dry cotton cloth internal optical parts never spray directly on the internal optical parts Spray onto a dry cotton cloth
15. ng We strongly recommend you carefully keep all the original gt Jme delivery packaging material in a safe place Any manufacture guarantee will become invalid if it is used An amp me having lost its guarantee may not recu perate it immediately even if an exten ded guarantee was bought beforehand FOR YOUR SAFETY PRECAUTIONS FOR USE Please read the following information carefully before using your E gt ne Voltage 90 250 VAC Check that the voltage matches that of your mains electricity Incorrect connection may cause irreversible damage that is not covered by the guarantee The EOne is for private and domestic use only It should not be used for professio nal purposes Do not disconnect by pulling on the E gt ne lead Do not use an extension cord with the E gt One Never handle the gt One with wet hands The E One must not be used in the shower or bath or in any place where water may splash onto it applicator or base Never immerse the E gt One base applicator or Optic cartridge in water Never use the E gt One if it is damaged if faulty operation is indicated on the touch screen or if it has been dropped non visible damage may put your safety at risk This item can only be repaired using specialised tools In the event of any after sales problems please contact us via our website on www e swin com via your personal area The Optic cartridges and all other accessories should only b
16. on places the E gt One in pause mode thus disabling emission of shots from the applicator Press icon l2 to leave the pause mode This icon is used to change the selection made pre viously on icons 7 8 3 and Il The E gt One can be switched on and off by means of this icon These icons make it possible to browse the various E gt One menus Real time information display These characters enable menu browsing and language selection and can be used to enter a personal identifica tion number or Optic cartridge activation codes Consumable level gauge Optic cartridge O This icon is used to confirm the information entered in the characters no 17 I BEFORE EACH USE HAIR REMOVAL WITH THE EOne e Check that the mains lead is not pinched or squashed and that there are no bare wires e Check that there is no visible damage to the cable linking the base to the applicator e Check the E gt One s external and internal optical parts Checking the external optical parts gt Check that the applicator s glass tip light guide is intact If it is not the case light guide split or chipped it must be changed This part can be ordered on the www e swin com website go to Client corner New Accessories Order mobile applicator head Checking the internal optical parts gt Before switching on and using your E gt One please check that all internal optical parts are intact tube filter red
17. pendix Il Article 3 and is EC labelled by SGS It therefore meets the requirements of the EN 60601 1 EN 60601 1 1 EN 60601 1 2 EN 60601 1 4 standards and appendices and standards EN 60601 1 6 and EN 60601 1 8 The EC certificate is available on the website at www e swin com I PRECAUTIONS FOR USE The base and the applicator must not come into contact with water To avoid exposure to high voltages do not attempt to open the base or the applicator Never use any cartridges or accessories other than those designated and sold for the E gt One and by E SWIN I PROTECTION OF THE ENVIRONMENT Local legislation must be observed when disposing of the packaging and consumables Promote effective recycling as far as possible RECYCLING AND REPROCESSING Directive relating to the reprocessing of waste products The WEEE Directive Waste Electrical and Electronic Equipment 2002 96 EC was implemented in order to ensure that products are recycled using the most effective processing recovery and recycling techniques available and thus contribute to protecting the environment and human health Your product has been designed and manufactured using high quality materials that can be recycled and reused E SWIN SAS is a member of an environmental organisation responsible for collecting and processing our products at the end of their life cycle Do not dispose of your product with your usual household waste Ensure that you dispose of yo
18. r black skin please consult our website at www e swin com Clinical information section e On damaged burnt or infected skin e On skin having suffered sunburn and healed less than one month ago e On skin lesions requiring a medical opinion e On high risk areas spots birth marks warts unhealed wounds etc KEEP OUT OF THE REACH OF CHILDREN On moles if moles are present in the area in which hair is to be removed they must be protected using the Patches provided with the E gt One On tattooed areas make up tattoo lip contour for example or aesthetic tattoo regardless of the colour The StON marking plate provided with your E One should be used in these cases If you have a skin disorder eczema inflammation acne etc If you are receiving photosensitizing treatment ask your doctor for advice If you have a history of dermatological disorders Please seek medical advice before using the E ONGe Not to be used on animals Only use the pen the gel Patches stop marking plate and Mask provided with your E gt One The use of any other products may lead to skin burns LEXICON BASE APPLICATOR Light guide tip Mobile head Mobile head sprockets Trigger Lower button shell yy Applicator lead storage N y Air ready LED vents Upper shell INFORMATION PROVIDED BY THE EOne TOUCH SCREEN D The steady state icon indicates that no component is overheat
19. re attached to the applicator photo 29 The copper contact studs at the base of the applicator If you have inadvertently touched the tube or its reflec tor we recommend that you return your cartridge to us in order to have it replaced ISTEP 6 e Before repositioning the mobile part of the applicator always clean the filter in the applicator head on the accessible side with the clean spray photo 35 The filter is the red glass part ISTEP 7 e Snap the mobile part back in by pressing gently as shown opposite ISTEP 8 ACTIVATION CODES e Plug the E One in e Switch it on by pressing the on off icon bottom left After validating the Optic cartridge replacement request a message is displayed asking for the first activation code of the cartridge inserted to be entered You will receive the activation codes after your order is sent on the Client Corner and by following the instruc tions after having clicked on K7 optic activation codes They are then available in the section My messages and sent to your email address These acti vation codes are unique and take into consideration the serial number of your machine and will not work on any other E gt One machine CHANGING THE OPTIC CARTRIDGE Using the browser icon 16 see page 15 enter the first code provided 5 digits Icon 16 enables you to change the digit in each box and move from one box to another Once the full code has been ent
20. s e Apply the gel in a thin layer to the area to be treated Observation if you wish to treat a large area do not spread the gel on the whole area straight away as it will dry and become ineffective in terms of optical transmis sion Spread the gel on the area in question gradually as you go Once the gel has been applied to the skin and treated it must not be reused on another area Once the gel has been subjected to a shot changes are likely to occur in its optical characteristics e Put the mask mask on Any other persons in the vici nity during use must also wear a MASK Important do not apply shots to the periocular area under the Mask protecting your eyes eyebrows eyelashes etc a V TIPS a a o Reminder the Pen Gel Patches stop marking plate and mask should be provided with your ENE The use of any other products may lead to skin burns and are not covered by the guarantee e If necessary use the StOP to hide any large areas not to be treated tattoo etc To remove easily the applicator from its base you should hold its A A big white cable and lift up The applicator can be then taken down easily i e Shot emission To be able to emit shots the glass applicator tip The applicator must only be used once the If you mien E he the ladies anter uas dl light guide must be placed on the skin Pressure SN ereen light is on if the applicator is pressed se wait 2 k e nn as o must then be
21. t guide with a damp cloth e Finish cleaning with the spray photos 19 and 20 STEP 3 Great care must be taken when changing the cartridge Incorrect handling may lead to irreversible damage to the applicator and to the E gt U ne in e Switch the EOne off general In the event of improper handling the guarantee will no longer be valid We therefore recom a R l mend that you follow the official procedure closely ee ine mame STEP 4 STEP 1 e Release the mobile part of the applicator by pressing on either side as shown in photo The cartridge must be changed when Change cartridge is displayed on the screen e Remove the mobile part from the fixed part photo The Optic cartridge must not be changed before this message is displayed Cartridges changed too early cannot be used again e Gently place the mobile part on a flat surface e identify the cartridge positioning notches photo 25 e Take the cartridge by the notches e Gently extract the cartridge photo l You may track the cartridge status on the touch screen at y ge p any time e Remove it completely photo 27 TAPE 2 e Wait for the fan in the applicator to stop before switching off and unplugging your E gt One this may take a few minutes This procedure enables the internal optical parts of the applicator to cool down ISTEP 5 INSERTING A NEW CARTRIDGE e Identify the way in which the new cartridge should be
22. the old cartridge and you switch the E gt One on instead of validating the Depilation menu you must change the menu by pressing icon 16 3 menus are available in all Epilation Change cartridge Configuration To change the PIN you must follow the instructions on the screen Enter the old PIN then the new PIN etc You may quit this sub menu using the cursor key adjacent to this line of information e Language selection Select the Change cartridge menu and enter the new e Key Beep the key Beep is activated by default but it can also be deactivated codes as during the standard procedure To protect the environment please use the Optic cartridge packaging to return the used cartridge to us WHAT NOT TO DO I BELOW IS A NON EXHAUSTIVE LIST OF WHAT NOT TO DO WITH YOUR E One The following are prohibited as they may endanger your own personal safety or cause irreversible damage to your EON USING THE ACCESSORIES The pen is used to circle the area to be treated before the gel is applied Important this pen only must be used to mark out the areas to be treated and is designed to be shot resis tant Any other pen or pencil may cause skin burns if the pulse is directed on the line drawn on the skin PEN Made in China The gel must be stored at ambient temperature It is to be applied in a thick layer gradually throughout the session to prevent it from drying on the skin O
23. ur E gt One in containers for the separate collection of electrical and electronic equip ment bearing this symbol Please use one of the following reprocessing options 1 Dispose of the E gt One in its entirety including the cables plugs and accessories in designated WEEE col lection points 2 If you have purchased a new replacement product return your old product in its entirety to E SWIN SAS in its original packaging GUARANTEE Your E One is covered by a two year guarantee for private and domestic use only The guarantee does not cover any connection errors improper handling or use other than that for which the E gt One is intended E SWIN declines all responsibility for any accident occur ring from improper use or non observance of the instruc tions in this manual or in the information provided on labelling or on the touch screen The 2 year manufacturer s parts and material guarantee is only valid if the item is returned in its original packaging Please keep the packaging in which the E gt One was delivered in a safe place For after sales advice or ordering spare parts consult our website at www e swin com WWW e swin com 0120 y 00 NO 00
Download Pdf Manuals
Related Search