10W LED COLOR SPOT
Contents
1. Unit Dip switches setting Slave 1 dip on 1 1 Slave 2 dip on 1 3 1 4 5 1 N MD0090000N N 1234567 8 910 Slave 3 dip on 1 4 1 8 9 2 VOODOO Slave 4 dip on 1 3 4 1 4 8 13 ON 1234567 8910 3 SOOWOCOO0U ON 12345678910 4 hd FA WOE i ON 12345678910 4 3 Easy Coniroller by CA 8 CA 9 CA 9RTX A The easy remote control is used only in master slave mode By connecting 2 o to the 4 pin jack of the first unit you will find that the remote controller on the first unit will control all the other units for Stand by Function and Mode selection Blackout Blackout the unit Strobe Select color 1 Synchronous strobe in white 1 Red 2 Sound strobe in white 2 Green 3 Sound strobe in color 3 Blue 4 White 5 Red Green 6 Red Blue 7 Red White Function 8 Green Blue 9 Green White 10 Blue White 11 Red Green Blue 12 Red Green White 13 Red Blue White 14 Green Blue White 15 Red Green Blue White 16 Color change by sound Mode Sound LED OFF Manual Color LED ON When using a universal DMX controller to control the chain of units you can set DIP switch 10 OFF to select 3 channels mode and set it ON to select 4 channels mode After choosing channel mode you have to set DMX address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal Please refer to the following d2. Acme LINKABLE M arv o Rae Activation STAND ALONE 10W LED COLOR SPOT VA M 7 LED PS10D RGBW User Manual Professional Entertainment Technology TABLE OF CONTENTS 1 Safety Instruction 2 Technical Specification 3 Installation 4 How to Control the Unit 4 1 Control Panel 4 2 Master Slave operation 4 2 Easy controller 4 4 Universal DMX controller 5 DMX 512 Configuration 6 DMX 512 Connection 7 Trouble Shooting 8 Fixture Cleaning 1 Safety Instruction A N Please read the instruction carefully which including important information about the installation operation and maintenance WARNING e Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet e Unpack and check carefully there is no transportation damage before using the unit e Before operating ensure that the voltage and freguency of power supply match the power reguirements of the unit e It s important to ground the yellow green conductor to earth in order to avoid electric shock e The unit is for indoor use only and use only in a dry location e The unit must be installed in a location with adeguate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked e Disconnect mains power before fuse replacement or servicing e Replace fuse only with the same type e Make sure there are no
3. DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may NRD cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller Check the LED for the response of the master slave mode signal Check if the unit is receiving DMX signal and cut it off No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tapping the microphone One of the channels is not working well The stepper motor might be damaged or the cable connected to the PCB is broken The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning freguency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 10 Innovation Ouality Performance 11
4. Weight 2 0kg 174 115 3 Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The eguipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 4 How To Control The Unit D Hanging bracket With 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook Optical Lens Turn the lens to change the focus and obtain sharp gobos 3 DIP Switches Set the different function settings 4 Microphone Receives the sound to control the unit 6 6 Only for remote control Connecting with CA 8 CA 9 CA 9RTX to control the unit for Stand by Function and Mode 7 Safe Ring For attached the safe cable Heat sink for the LED Do not cover this part to ensure proper cooling 9 DMX input For DMX5
5. 12 link use 3 5 pin XLR plug cable to input DMX signal 0 DMX output For DMX512 link use 3 pin XLR plug cable to link the next unit Q Mains input Connect to power supply 4 2 Master Slave Operation The unit can be linked together in daisy chain as many as you need in master slave mode the first unit will control the others to give a coordinate automatic light show and i s good for instant shows In Master Slave mode refer to the DMX settings below Master unit Set DIP switch 1 9 to OFF Slave units The DMX start address may set to any value but 0 gt 4 Light show Set dip switch 1 9 to OFF for the first unit which has nothing in its DMX input jack Set the DMX address of other units to 1 4 7 or 10 when the dip switch 10 OFF or set the DMX address of other units to 1 5 9 or 13 when the dip switch 10 ON then the units slave will follow the first unit master to run built in program for 4 Light show The slave units which don t set the address as mentioned aforementioned will run as slave 1 Dip switch 10 OFF Unit Dip switches setting Slave 1 dip on 1 1 Slave 2 dip on 43 4 1 A ala alelu aja SI 3 dip on 41 H2 3 1 2 4 7 0 ou 1900000000 Slave 4 dip on 2 4 2 8 10 ON 12345678910 3 U0U000000D ON 12345678910 4 9000000000 ON 12345678 910 Dip switch 10 ON
6. Color 8 096 111 Color 7 080 095 Color 6 064 079 Color 5 048 063 Color 4 032 047 Color 3 016 031 Color 2 000 015 Color 1 255 00 255 100 oF 0 255 100 oF 0 255 100 0 0 6 DMX 512 Connection The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels O wy amp HT COMMON i N DMX INPUT SUA DMX OUTPUT DMX Termination reduces signal errors and voids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 1f you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it i
7. iagram to know how to address your DMX 512 system in the binary code DMX 512 Address Chart Dip switches 1 2 3 4 5 6 7 8 9 10 Value 1 2 4 8 16 32 64 128 256 Channel mode Unit Dip switches setting Dip switch 10 OFF Channel 1 dip on 1 1 1 1000000007 ON 12345678910 Channel 2 dip on 3 4 i Channel 3 dip on 41 42 3 1 2 4 7 2 ON NALDEDODAN Channel 4 dip on 2 4 2 8 10 3 VUT p A eS eID 4 09000N800D ON 12345678 910 Dip switch 10 ON Channel 1 Channel 2 Channel 3 Channel 4 dip on 1 1 dip on 1 3 1 4 5 dip on 1 4 1 8 9 dip on 1 3 4 1 4 8 13 5 DMX 512 Configuration Unit Dip switches setting 1 otin 2 1009000000 ON 12345678910 3 105000000 ON 12345678910 4 900000000 ON 12345678910 DMX512 Configuration 3 Channel Mode 4 Channel Mode Ch1 Ch2 Ch3 Ch1 Ch2 Ch3 Ch4 Dimmer Strobe Color Red Green Blue White 255 100 0 0 248 255 Sound Active 555 55 8 247 0 7 No Strobe 240 255 Sound Active 224 239 Color 15 208 223 Color 14 192 207 Color 13 176 191 Color 12 160 175 Color 11 144 159 Color 10 128 143 Color 9 112 127
8. n the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not be branched or split to a Y cable DMX 512 is a very high speed signal Inadeguate or damaged cables solder joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is connected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 512 usually 0 8 1 are equal to 1 6 The end of the DMX 512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 5 Not used 7 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A NRD The fixture does not work no light Check the connection of power and main fuse Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX connectors cables to see if link properly If the DMX LED is on and no response to the channel check the address settings and
9. t flammable materials close to the unit while operating as it is fire hazard e Use safety cable when fixes this unit e Maximum ambient temperature is TA 40 C and don t operate it where the temperature is higher than this e Unit surface temperature may reach up to 60C Don t touch the housing bare hand during its operation e There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may reguire service please contact the nearest authorized technical assistance center and always use the same type spare parts e Don t connect the device to any dimmer pack or power pack e Do not look directly at the LED light beam while the fixture is on e The housing must be replaced if they are visibly damaged e Donottouch any wire during operation as high voltage might be causing electric shock 2 Technical Specification Features a 10W guad color high powered LED creating vivid colors that are suitable for mirror ball projection or for color changing performance 3 Operation Mode DMX Master Slave 8 Sound Active Optional easy controller CA 8 or CA 9 RTX for instant lighting shows at your fingertips No heat low power consumption no duty cycle runs all night Ideal for clubs bars discos parties mobiles DJs etc Voltage AC 100 240V 50 60Hz LED 1 x 10W quad color LED 50 000 hrs rated Power Consumption 14 9W Dimension 187 x 156 x 115 mm
Download Pdf Manuals
Related Search