Home
S8011030 - User Manual for Master Two
Contents
1. e LI et rel 21 U Ra Optical Coaxial Audio Audio e RGBHV Back of Master Two DW VGA 640x480 SVGA 800x600 XGA 1024x768 and SXGA 1280x1024 resolutions are supported at 60 Hz 16 LLL 8011030 Master Two User Manual 3 0 SETUP 3 2 Audio Operation The Master Two features an audio delay function to exactly match the video delay incurred by the video processing It accepts four discrete digital audio inputs two coaxial Audio 1 2 and two optical Audio 3 and 4 one analog audio input and four HDMI audio inputs The locations of the audio inputs are shown on the back panel diagrams earlier in this product guide The factory default audio assignment is as follows Audio 1 optical Component 1 Audio 2 optical S Video 1 Audio 3 coaxial S Video 2 Audio 4 coaxial Component 2 Stereo analog Video 1 Note The HDMI audio inputs can only be assigned to the same HDMI video input although any of the other audio inputs can be assigned to any of the HDMI video inputs You can assign a Digital Audio input to each Video input in the following manner You can assign an audio input to each Video input in the following manner 1 Select a video input on the remote control 2 Select Audio 1 2 3 4 Stereo HDMI or Off from the Input Adjust Audio Input menu If an analog video input
2. CC C3 C HDMI 2 COMP1 S VIDEO1 VIDEO CD CD CD C2 HDMI 3 COMP2 S VIDEO2 VIDEO2 Input Select HDMI 1 HDMI 2 HDMI 3 HDMI 4 Component 1 Component 2 RGBHV Component S Video 1 S Video 2 Video 1 Video 2 AUTO HDMI 4 RGBHV AUTO INPUT SELECT Power Standby Buttons The Master Two remote has a Power and a Standby button The Power button always turns the Master Two on and the Standby button always put the unit into Standby mode Curtain Button The Master Two remote has a Curtain button which allows you to close a curtain over the image This feature is especially useful when an image is paused on a display susceptible to burn in Remote Control Battery Installation The remote control for the Master Two requires two AA batteries These should be replaced as needed ABT recommends Alkaline batteries because they last longer without leaking To install the remote control batteries 1 Locate the battery compartment on the back of the remote control 2 Remove the cover from the back To do this press the tab attached to the cover and pull the cover with the guide on the back of the remote control 3 Remove the old batteries if applicable 4 Insert two new AA batteries in the compartment as shown on the inside of the battery compartment Make sure the batteries are correctly inserted observing the proper polarity 5 After installation replace the cover and dispose of
3. gt 60Hz gt Unlock gt 50 00 For displays that will only display 60Hz NTSC Output Setup gt Framerate gt 50Hz gt Unlock gt 59 94 Output Setup gt Framerate gt 60Hz gt 60Hz Lock Display Calibration Test Patterns Used Brightness Contrast Color8 Bars75 Color8 Bars100 Gray Ramp The Master Two has several test patterns to assist in the setup of your display Adjustments should be made on your display not on the Master Two to correctly setup your Master Two and display The Brightness Contrast test pattern will assist you in setting up both the brightness black level and contrast white level of your display The Brightness Contrast test pattern is composed of 4 quarter screen blocks Two of the blocks have a background level of standard black and the other two blocks have a background level of standard white Embedded in the black blocks are 3 bars One is 4 IRE below black blacker than black one is 1 IRE above black and the third is 2 IRE above black Embedded in the white blocks are 3 bars One is 1 IRE above white whiter then white one is 1 IRE below white and the third is 2 IRE below white The bottom two blocks differ slightly from these levels For the bottom two blocks the blacker than black is at the lowest possible luma level and the whiter than white bar is at the highest possible luma level When the brightness and contrast are adjusted correctly you should be able to see the 1 IRE an
4. 480i 576i input when you use the Line Offset function This function can be set independently for both 480i and 576i input formats Color Space The color space setting allows the user to specify what the input signal is on the RGBHV Component and HDMI inputs The YPbPr setting only applies to the RGBHV Component input The YCbCr 4 2 2 and YCbCr 4 4 4 and Auto settings only apply to the HDMI inputs The options are RGB YPbPr YCbCr 4 2 2 color space YCbCr 4 4 4 color space Auto Input Level The input level setting allows the user to specify the levels of the input signal either Video 16 235 or PC 0 255 Video PC VCR Mode VCR Mode decouples the output timing completely from the input timing to ensure a stable output from the Master Two for VCR playback especially during trick play modes play forward play reverse still pause On Output timing is decoupled from the input timing regardless of Frame Rate settings Off Output timing is dependent on Frame Rate settings Auto Turns on VCR Mode if a VCR source is detected Film Mode S8011030 Master Two User Manual 4 0 MENU OPTIONS Film Mode allows you to control the film mode operation of the Master Two Usually the automatic film mode detection is preferred However there are some cases where the detection needs to be turned off or biased towards film Off Turns off film detection in the deinterlacer All video sources are treated as original video Film Bia
5. Analog If you don t press the Up button once and the press Enter You should see Output Setup Analog Digital on the FPD 6 Press the Down button four times You should see Output Setup Color Space on the FPD 7 Press the Enter button once You should see Color Space YPbPr on the FPD If you don t press the Up but ton once and press Enter You should see the Master Two s on screen Display OSD on your screen The Master Two cannot output a component signal if the input signal is from a DVI or HDMI source with HDCP Instead the Master Two outputs a blue screen Displays with a VGA HD 15 or 5BNC RGBHV input 1 Press the Menu button on the front panel of the Master Two once You should see Main Menu Input Select on the FPD 2 Press the Up button once You should see Main Menu Output Setup on the FPD 3 Press the Enter button You should see Output Setup Analog Digital on the FPD S8011030 Master Two User Manual 3 0 SETUP 4 Press the Enter button You should see Analog Digital BNC Analog If you don t press the Up button once and then press Enter You should see Output Setup Analog Digital on the FPD 5 Press the Down button four times You should see Output Setup Color Space on the FPD 6 Press the Enter button once You should see Color Space RGB on the FPD If you don t press the Up button once and press Enter You should see the Master Two s on screen Display
6. OSD on your screen The Master Two cannot output an RGBHV signal if the input signal is from a DVI or HDMI source with HDCP Instead the Master Two outputs a blue screen STEP 3 Connecting Your Sources to the Master Two Up to 12 video sources can connected to the Master Two Use the following suggestions for connections to several popular video sources VCR LD Player DVR VCR LD Player DVR Back of Master Two Some VCRs and LD players have S Video outputs These give an improved picture from these sources If your LD player or DVR has a digital audio output CineVERSUM recommends you use that connection S8011030 Master Two User Manual 2 2775s 13 3 0 SETUP 14 DVD Player DVD Recorder DVD Player DVD Recorder Q O00 000 o O5 em ooo U SDI OUT DVI D OUT HDCP HDMI OUT COMPONENT OUT OPTICAL COAXIAL Coaxial Optical Audio Audio Back of Master Two Note If you have a display with an HDMI DVI input CineVERSUM recommends you use the DVI HDMI output of your DVD player with the player s output resolution set to the lowest output resolution preferably 480i If you have a display with only component or RGBHV inputs use either an SDI or component video connection SDI outputs typically need to be added to your DVD player This gives the additiona
7. and Color8 Bars100 will assist in setting up the saturation color and hue tint of your display The Color8 Bars75 test pattern consists of 8 vertical bars across the screen at a 75 saturation level The Color8 Bars100 test pattern consists of 8 vertical bars across the screen at a 100 saturation level From left to right the S8011030 Master Two User Manual 5 0 APPENDIX bars are white yellow cyan green magenta red blue and black To properly adjust the saturation and hue you will need to use the blue colored filter that comes with AVIA You will also need to turn off any automatic flesh tone controls on your display before making these adjustments When the Saturation and Hue are adjusted correctly the white bar and the blue bar should be exactly the same shade when looking through the blue filter Saturation and hue settings interact with each other so after making this setting you may want to go back and check that the saturation setting is correct The Gray Ramp can help verify that your display is showing the gradients between black and white correctly You should see a smooth transition between black and white with this test pattern Special Equipment Needed for Display Calibration To assist in this calibration theMaster Two includes IRE windows to be used with the proper calibration equipment Test Patterns Used Window IRE10 Window IRE20 Window IRE30 Window IRE40 Window IRE50 Window IRE60 W
8. the selected display profile is used independently of the active input S8011030 Master Two User Manual 5 0 APPENDIX 5 0 APPENDIX 5 1 Non Volatile Memory Settings The Master Two stores a variety of user settings in non volatile memory Non volatile memory retains its contents when power is lost There is one group of system settings and one group of user settings System Settings Setting Display Profile Auto Display Profile Description One of ten display profiles or User If enabled selects a display profile based on input selection Active Input One of many Master Two inputs or auto Active input Auto StandBy Off or On Video Priority Priority list of inputs when Auto Active Input is on User Mode Normal or Advanced Border Level Blank to quarter gray Pass Through Input mode is Pass through or not Power LED On Off or Auto Test Pattern Generator SDI Line Offset Current selected test pattern One for 50Hz input and one for 60Hz input Serial Port Bit Rate HDMI Config Input Format Settings Select an available baud rates Current selected parameters Table 2 System Settings The Master Two supports an independent set of saved settings based on input and format Settings Input Format 1 Composite 1 NTSC 2 Composite 2 PAL SECAM 3 S Video 1 NTSC 4 S Video 2 PAL SECAM 5 Component RGBS 1 480i NTSC 6 Component RGBS 1 576i PAL SECAM 7 Component RGBS 1 480p NTSC 8 Compone
9. 4 3 1 5511 1 66 1 1 78 1 16 9 1 8511 2 85 1 To use aspect ratio s in addition to these the Master Two provides the option to choose a custom aspect ratio called User with a range of 1 01 1 3 00 1 Master Two Image Mapping The situation when the Frame Aspect Ratio FAR is the same as the Active Aspect Ratio AAR is sometimes called Full Frame This situation is illustrated below The Master Two maps the AAR to the Output Aspect Ratio OAR in the following three ways When the AAR is greater than OAR the Master Two puts up Borders at the top and bottom as shown below Active Input Area Borders When the AAR is less than the OAR the Master Two puts up Borders on the left and right as shown below Active Input Area Borders When the AAR is equal to the OAR Output Aspect Ratio the Master Two supplies no border as shown below S8011030 Master Two User Manual 22 19 4 0 MENU OPTIONS 20 Panorama The Panorama feature is a non linear stretch that can be applied only to a 4 3 video source The panorama stretches the picture with minimal perceptual distortion in the center of the screen This mode can be turned On or Off Additionally this feature can be accessed in the IAR presets and it is titled 4 3 Stretch Zoom The Zoom function zooms in on or magnifies the image on your display The minimum zoom is 10096 no zooming the maximum zoom is 15096 zoom magnification
10. 60 HDMI 4 576p PAL SECAM 61 HDMI 4 720p ATSC 62 HDMI 4 1080i ATSC 63 HDMI 4 VGA 64 HDMI 4 SVGA 65 HDMI 4 XGA 66 HDMI 4 SXGA Table 3 Input Format Settings Note There is a separate set of settings not just for each input but for each format as well This provides a lot of flexibility but is complex For example you can make settings for an input with an NTSC source but when the source is changed to PAL you must specify new settings S8011030 Master Two User Manual 5 0 APPENDIX Format settings Each Input Format contains the settings below Setting Description Picture Control Brightness Contrast Saturation Hue Sharpness Chroma Error Correction Y C Delay Display Profile Profile 1 10 or User Audio Select Audio 1 4 Audio Delay Overscan VCR Mode Film Mode Pass Through Input A R Preset Preset 1 10 or User Preset User Preset Frame AR Active Input AR Pre defined or User AR User AR Hor Zoom Hor Zoom Vert Zoom Vert Zoom Hor Pan Hor Pan Vert Pan Vert Pan Hor Borders Hor Borders Vert Borders Vert Borders Table 4 Input Format settings There is only one set of presets Preset 1 through Preset 10 for the whole system However the User Preset is per input and per format 5 2 Setting up an Master Two Using the Internal Test Patterns The Master Two has 35 built in test patterns to assist in the setup of your display and your individual source
11. AV LAD SYNC EE 23 44 Picture Controls iret ira ne crei Ra rubei Rabe tr nena Ra ibd a rad er tin et tete 23 Sel E C ERES 23 COMMAS m 24 SEMI M 24 ulf e 24 Shatpli6SS Re engen essit es 24 S8011030 Master Two User Manual NIC Delay ER Rite 24 Chroma Filter Auto CUE C iii 24 4 5 e lt T e 111 eT certc rerit tenerte motos de abe donnees der desert orne 24 TeSUP alterris 2 ite iuum R mr 24 Auto Standby eere nte ete teint entente dtd testo Couteau eda idees ans tects 24 LED Brightiless rerom edipi a entente tre tee 25 De e c Heena Eaa ahalen 25 SerialPort FACS araa a e a A 25 Factory Default cdit ct AR S 25 Software Update D 26 LSIEN e aaa Saa E 26 MEE 26 Analog Digital A D s Iota nee eoe siden uvis Cose eam rade men hate 26 OUTPUT FORM AL aceite ences CEDERE 26 Output Aspect Ratio e cle 2 etre te pectus m rites 27 Syne TyDO iue idee E litur edo demtst ie dees cee AE 28 COIR SPACC E 29 SuUgkl lm 29 Framerate Conversion 29 BOrd r LGT tetes tee T 29 HDGP MOde 22 MR 29 IVA 29 50 APPENDIX onii 31 5 1 Non Volatile Memory Settings aa e EO a 31 System SOUINGS cette reete der hd o te e DU deanad aeaiia ad
12. cannot select the format until you press the Exit button Press the Enter button again to select the output timing controls explained in the Output Timing section Horizontal Vertical Sync Signal Sync Signal Resolution Resolution Scan Type Line Type Colorspace 720 480 P Y Bi level YPbPr 1920 540 P Y Tri level YPbPr 720 576 P Y Bi level YPbPr 1280 720 720p 50 P Y Tri levle YPbPr 1280 720 720p 60 P Y Tri level YPbPr 1920 1080 1080i 50 Y Tri level YPbPr 1920 1080 1080i 60 Y Tri level YPbPr 1920 1080 1080p 50 P Y Tri level YPbPr 1920 1080 1080p 60 P Y Tri level YPbPr 640 480 P Y Tri level YPbPr 800 600 P H V E RGB 1024 768 P H V RGB 1280 1024 P H V RGB 852 480 P H V E RGB 852 576 P H V RGB 1366 768 P H V RGB 1280 768 P H V RGB 1024 1024 P H V RGB 1024 852 P H V RGB 1024 576 P H V RGB 848 600 P H V RGB 1365 1024 P H V RGB 1400 1050 P H V RGB 1400 788 P H V RGB 960 540 P H V RGB 1280 960 P H V RGB 1440 960 P H V RGB 1440 1152 P H V RGB Table 1 Preset Formats and Characteristics for Analog Video Output Output Aspect Ratio Control There are four controls for Output Aspect Ratio OAR Display Aspect Ratio Screen Aspect Ratio Image Shift Underscan S8011030 Master Two User Manual L2 o 222 27 4 0 MENU OPTIONS 28 The Display Aspect Ratio is the full aspect ratio of the display normally specified in the display manual Common displ
13. factor of 1 5X Horizontal Zoom Control Push the Enter button to show the current Zoom setting Push the Up and Down button to increase or decrease the zooming factor Vertical Zoom Control Push the Enter button to show the current Zoom setting Push the Up and Down button to increase or decrease the zooming factor Pan The Pan function allows the image to be shifted up down left and right Note that the Pan function can only be used after the image has been zoomed to any value greater than 100 Horizontal Pan Control Push the Enter button to show the current Pan setting Push the Up button to pan to the right Push the Down button to pan to the left Vertical Pan Control Push the Enter button to show the current Pan setting Push the Up button to pan up Push the Down button to pan the image down Borders The Borders function allows you to add horizontal and or vertical borders around the image These borders obscure part of the input image Certain input to output aspect ratios already result in left right or top bottom border being added This control allows the system generated borders to be extended or for borders to be added when none exist As the borders are adjusted see below theMaster Two temporarily increases the gray level of the borders so that they are visible during the adjustment process The level will return to normal after the adjustment has ceased Horizontal Border Control Push the Up button to mo
14. make each adjustment You can find the guided setup by clicking Advanced AVIA from the main menu and then selecting Basic Video Adjustments on the following menu page Each picture control is explained in depth and the narrative will tell you what to look for in a properly adjusted display Once you have made these adjustments there are several patterns on the AVIA DVD that can be used in conjunction with the built in test patterns of the Master Two to verify the settings are correct Access these as follows 1 After inserting the AVIA DVD into your DVD player press the top menu button to bring up the main menu 2 From the main menu select Advanced AVIA 3 On the right hand side of the Calibrations menu page select Video Test Patterns 4 From the Video Test Patterns menu select Gray Scale amp Levels 5 From the Black and White Levels menu select the Needle Pulses test pattern This is to be used with the Half B W internal test pattern from the Master Two 6 Once you have adjusted brightness and contrast go back to the Video Test Patterns menu and select Color Adjustment 7 From the Color Adjustment menu select Special Color Bars Use the Full Bars test pattern in conjunction with the H Clr7 Bars75 internal test pattern from the scaler Use the Full 100 Bars with the H Clr7 Bars100 internal test pattern 5 3 Troubles
15. not be able to bypass the internal processing on your display S8011030 Master Two User Manual 85 5 0 APPENDIX 36 The Vertical Lines test pattern should appear as one pixel wide black and white columns If you see any irregular pattern s in the image you know that the display is scaling the signal horizontally To override the internal scaling adjust the horizontal size of the image to see if the test pattern can be displayed correctly Output Setup Format User H Size Adjust The Horizontal Lines test pattern should appear as one pixel tall black and white rows If you see any irregular pattern s in the image then you know that the display is scaling the signal vertically To override the internal scaling adjust the vertical size of the image to see if the test pattern can be displayed correctly Output Setup gt Format gt User gt V Size gt Adjust The Judder test pattern displays a bar that bounces back and forth at the chosen output frequency selected in the framerate parameter When this test pattern is displayed correctly the bar moves smoothly across the screen and bounces from side to side When this pattern is displayed incorrectly this bar may tear as it moves across the screen To adjust the framerate conversion go to the Output Setup menu For displays that will only display 50Hz PAL Output Setup gt Framerate gt 50Hz gt 50Hz Lock Output Setup gt Framerate
16. one border level setting for the system To adjust the border level push the Up or Down button The current level is shown The default value is 0 Push the Up or Down button to decrease or increase the border level HDCP Mode There are two HDCP modes Off HDCP is disabled at the Master Two s HDMI output On The Master Two continuously looks for a HDCP display device on its HDMI output Display Profiles A display profile is a group of display parameters you can save and easily recall in the future A display profile consists of a set of display parameter selected from the Output Setup menu This includes the following Output Type Analog or Digital S8011030 Master Two User Manual L2 29 4 0 MENU OPTIONS 30 Format Resolution and all video output timing information Output Aspect Ratio Sync Type Color Space YPbPr YCbCr or RGB Output Level Video or PC Frame Rate Conversion information Border Level You can save up to ten display profiles Profile 1 through 10 A current custom display profile called User is also stored in non volatile memory However it will be overridden when you make any modifications to the display profile You should always save the current display profile to Profile 1 Profile 10 to prevent the custom profile from being lost The Display Profile feature is only enabled when you set the User Mode to Advanced just like the full control of output timing parameters in the Format men
17. receivers digital set top boxes game consoles or other digital audio devices These inputs are compatible with most consumer digital audio formats including CD Audio 44 1kHz 16 bit LPCM Dolby Digital and DTS The coaxial digital audio inputs are compatible with any format with a sampling frequency between 24kHz and 192kHz and with a data word structure up to 24 bits in length The optical digital audio inputs are compatible with any format with a sampling frequency between 24kHz and 96kHz and with a data word structure up to 24 bits in length The HDMI audio inputs are compatible with HDMI 1 1 audio formats Audio Outputs There are two digital audio outputs one coaxial and one optical Both are active at the same time with the selected input Digital Audio stream 2 3 Remote Control Overview The functions of these buttons are detailed in the next paragraph An asterisk indicates this feature will be implemented in future software S8011030 Master Two User Manual EE 9 2 0 BASIC OPERATION Curtain Info Standby Power8 Output Setup Test Patterns Left On Off Right Configuration Display Profiles Viewing Modes CONFIG Picture Control Input Aspect PICTURE Ratio CONTROL DISPLAY VIEWING INPUT PROFILES MODES ASPECT INPUT MEMORIES Input Adjust ADJUST MENU Menu Exit Navigation Keys Up Left Enter Right Down Border Aspect
18. Cr 4 2 2 HDMI 3 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz VGA SVGA XGA SXGA 60Hz RGB YCbCr 4 4 4 YCbCr 4 2 2 HDMI 4 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz VGA SVGA XGA SXGA 60Hz RGB YCbCr 4 4 4 YCbCr 4 2 2 SD SDI 480i 576i SMPTE 259M Compliant Note The Master Two is able to process HDCP protected signals However the output signal may be only visible if a valid HDCP supported display is hooked up to the Master Two s HDMI output connector The output signal would never be visible through the Master Two s analog BNC output connectors Video Outputs The Master Two has two video outputs one analog and one digital The analog output on the Master Two can output the following signal types YPbPr Component RGBHV RGsB RGBS The digital output on the Master Two can output either RGB 4 4 4 8 bit YCbCr 4 2 2 10 bit YCbCr 4 4 4 8 bit To connect the Master Two to a display that has a DVI input use either an HDMI to DVI cable or an adapter Audio Inputs There are nine 9 audio inputs on the Master Two Two 2 Optical Digital inputs Two 2 Coaxial Digital inputs One 1 Analog L R input Four 4 HDMI inputs While the digital and analog audio inputs can be assigned to any one of the video inputs the HDMI audio inputs are tied directly to the HDMI video signal connected on the same input The Master Two accepts digital audio sourced from DVD players satellite
19. Down button again to select the alternate mode Serial Port Rate The serial port is used by the automation system controllers to control the Master Two The serial port baud rate defaults to 19200 bps but can be changed using the Up or Down button The supported baud rates are 1200 bps 1 2K 2400 bps 2 4K 4800 bps 4 8K 9600 bps 9 6K 14400 bps 14 4K 19200 bps 19 2K 38400 bps 38 4K 57600 bps 57 6K Factory Default The Factory Default option allows you to reset system settings to the factory default 1 Press either the Up or Down button The FPD displays No 2 Press the same button to switch to Yes 3 Confirm this selection by pressing the Enter button The default factory settings are as follows Input Selection Auto Input Aspect Ratio 16 9 Picture Controls midrange 0 Chroma Filter CUEC Off Output Aspect Ratio 16 9 Output Resolution 1080p Sync Sync on Y Output Color Space RGB 4 4 4 Output Type Digital Auto Standby Off Frame Rate 60Hz input 1 1 source locked output 50Hz input 1 1 source locked output User Mode Normal Video Input Priority Settings 1 HDMI 1 2 HDMI 2 3 HDMI 3 4 HDMI 4 5 Component 1 6 Component 2 7 S Video 1 8 S Video 2 9 Video 1 10 Video 2 11 SDI S8011030 Master Two User Manual 22 jj 25 4 0 MENU OPTIONS 12 RGBHV Component Digital Audio Input Assignment Component 1 Audio 1 Compon
20. In this situation the closest preset is 1366x768 Output Setup gt Format gt 1366x768 2 Display the Frame Geometry test pattern to verify that the image is positioned correctly on your display Configuration Test Patterns Frame Geometry To turn the test patterns on and off use the Test Patterns button on your remote control You can also navigate backwards and forwards through the test patterns using the and gt buttons respectively S8011030 Master Two User Manual 5 0 APPENDIX Frame Geometry Test Pattern Displayed Correctly When this test pattern is displayed correctly it should look like this with a one pixel wide white border around the edge of the screen Frame Geometry Test Pattern The test pattern is almost displayed correctly You can see the 1 pixel wide white border on the top bottom and left side of the image but not on the right side of the image By adjusting the horizontal size of this signal to 1360 rather than 1366 you can get this test pattern displayed correctly on the display To change the horizontal size of the image you must first put the Master Two in Advanced user mode Configuration gt User Mode gt Advanced Output Setup gt Format gt H Size gt 1360 In some cases the output format is correct but the image just needs to be shifted to fill the screen correctly Do this by using the Horizontal and Vertical Shift options in the Output Setup menu Outpu
21. RS rae pda 31 Input Format Settings eee ek deese dex eain Rees Iud cand xu sSMER tee 31 FORMAL Settings T 33 5 2 Setting up an Master Two Using the Internal Test Patterns sese eee ee eee eee 33 Determining the Correct Output Resolution for Your Display 33 Initial Setup of the to Your Display 34 Display Calibration issanda mb te iet tei e Ete lta uen 36 Special Equipment Needed for Display Calibration 37 CRT Display Calibration iot en rt reve ree i reist te erus 37 SOUrCE Calibratio fett E 37 5 3 TTOUDIS SOON RET 38 My Master Two shows an error message 38 The picture has horizontal lines with the Output set to 1080p60 or 720p60 38 The picture is green when use the analog output of the Master Two 39 No picture when connect the Master Two to the HDMI input of my display 39 The Blue status LED blinks on the front panel of the Master Two 39 The Green status LED blinks on the front panel of the Master Two 39 Will lose the settings on my Master Two if update the software version 39 Complete Menu Tr amp 6 eerte dn tenere e dee ed ded nid devant 39 S8011030 Master Two User Manual 1 0 GETTING STARTED 1 1 Introduction Thank you for purchasing the Master Two Video processor powered by ABT This product delivers a level of quality among the
22. Sometimes there is a lag between the Luminance Y and the Chrominance Pb Pr or Cb Cr of the video signal This causes a color smearing because the color component of the image is not lining up properly to the black and white luminance component of the image The Master Two can compensate for these errors in the source signal by shifting the phase of the Y with respect to the C forward or backward to align them properly Use the Down and Up buttons to adjust the phase and observe the effects on your display to obtain the optimal setting The default is O Chroma Filter Auto CUE C This feature removes chroma upsampling errors CUE found in video sources which have been MPEG encoded and then improperly decoded Off No chroma filtering Use this setting if the source does not have a CUE problem On Chroma filtering is always on Use this setting if the source is known to have a CUE problem Auto Automatic chroma error detection and correction Use this setting when you don t know if a source has a CUE problem Also use this setting for all digital sources which use MPEG2 decoders DVD players digital satellite receivers and so on as it will also detect and correct chroma errors created by all sources of this type when the source is encoded as interlaced also sometimes called Interlaced Chroma Problem or ICP Configuration 24 Test Patterns The Master Two has 35 internal test patterns to assist in the setup of your in
23. VERSUM MASTER Two Part No S9001030 USER MANUAL www cineversum com Date 26052006 Part No S8011030 Changes CineVERSUM provides this manual as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose CineVERSUM may make improvements and or changes to the product s and or the program s described in this publication at any time without notice This publication could contain technical inaccuracies or typographical errors Changes are periodically made to the information in this publication these changes are incorporated in new editions of this publication Copyright All right reserved No part of this document may be copied reproduced or translated It shall not otherwise be recorded transmitted or stored in a retrieval system without the prior written consent of CineVERSUM Guarantee CineVERSUM provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee On receipt the purchaser must immediately inspect all delivered goods for damage incurred during transport as well as for material and manufacturing faults CineVERSUM must be informed immediately in writing of any complaints If the purchaser or third party caries out modifications or repairs on goods delivered by CineVERSUM or if the goods are handle incorrectly in particular if the systems are comm
24. Window IRE40 S8011030 Master Two User Manual Table 5 Complete Menu Tree 41 5 0 APPENDIX 42 Window IRE50 Window IRE60 Window IRE70 Window IRE80 Window IRE90 Window IRE100 Gray Ramp Xhatch Coarse Xhatch Fine Focus Half B W H Clr7 Bars75 H Clr7 Bars100 H Clr8 Bars 75 H Clr8 Bars100 Black White Red Green Blue Cyan Magenta Yellow Auto Standby OFF Led Brigthness ON Naviagation Normal User Mode Advanced Serial Port Rate Normal 4800 9600 14400 19200 38400 57600 Factory Default No Software Update Yes No Yes Output Setup Information Analog Digital BNC Analog Format HDMI Digital 480p 540p 576p 720p 50 720p 60 1080i 50 1080i 60 Table 5 Complete Menu Tree S8011030 Master Two User Manual 5 0 APPENDIX 1080p 50 1080p 60 800x600 SVGA 1024x768 XGA 1280x1024 SXGA 848x480 852x480 1366x768 852x576 1366x768 1 1366x768 2 1360x768 1 1360x768 2 1280x768 1024x1024 1024x852 1024x768 1024x576 848x600 1365x1024 1400x1050 1400x788 960x540 1280x960 1440x960 1440x1152 User Horizontal Shift Horizontal Size Horizontal Front Porch Horizontal Sync Horizontal Back Porch Horizontal Total Vertical Shif
25. ay aspect ratios are 4 3 and 16 9 Less common ones are 5 4 2 35 1 and others The example below shows a 4 3 projection with a 16 9 screen Active Output Area Mask 4 The region outside the Active Output area called the mask is inactive and only important for creating video timing signals for the display Input video data is never mapped to this region When the Display Aspect Ratio is not the same as Active Output Aspect Ratio the mask is set to blanking levels and always centers the position of the active area over the display area Image shift allows you to adjust the location of the image on your screen both horizontally and vertically when the Screen aspect ratio is not equal to the Display aspect ratio The example below shows 16 9 projector 1 78 1 and a 2 35 1 screen you can shift the image to match the exact location of your screen In this situation the image is shifted down putting all of the mask at the top of the projected image Screen Aspect Ratio Mask 2 35 1 Screen Aspect Ratio 2 35 1 Underscan represents the visible display area a sub set of the Active Output Area Underscan is like a negative zoom which preserves the aspect ratio of the active area The default for this setting is 0 As you increase underscan the smaller portion of the active display area appears while preserving the aspect ratio of the active display area Active Output Sync Type The Sync Type option sets the
26. ay make black look gray In general you should adjust this up until you see the black areas of your display turn gray and then back it down just below that point Default setting is O midrange Contrast Contrast adjusts the ratio between white and black signal levels and is effective as a gain control The difference between this and the Brightness control is that this adjusts the difference between the brightest and darkest part of the image Note that all displays have a maximum white level Going beyond this level only clips the upper gray levels and you will lose color resolution at the brighter levels Adjust this control up until you see the brighter levels of the image begin to wash out At this point back it down just below that point The default setting is O midrange Saturation The Master Two allows you to control the saturation of the image independent of the display Saturation is the same as the Color control on most TVs and controls the richness of the color in the image The default setting is O midrange Hue As with Saturation hue can also be controlled independent of the display Hue is the same as the Tint control found on most TVs and controls how colors are displayed in the image The Hue control is not available for Component or PAL SECAM inputs The default setting is O midrange Sharpness The Sharpness setting adjusts the sharpness of the selected input signal The default setting is O Y C Delay
27. d 2 IRE above black bars on the black background and the 1 IRE and 2 IRE below white bars should be visible on the white background When the brightness is adjusted correctly black objects should appear black with the details still intact and lighter areas should be light not gray with the details still intact When the contrast is adjusted correctly white objects will appear white with the details still intact Because the contrast settings can affect brightness settings we recommend that you check the brightness setting after making this adjustment Note If you have a CRT based display following the instructions above may yield a contrast setting too high If the contrast is set too high you will get blooming and loss of details in the highlighted areas It is more helpful to use the two vertical lines in the test pattern Adjust the contrast up and down and you will notice that these lines will bend as you increase the contrast To properly adjust contrast on a CRT based display decrease the contrast until the vertical lines start to straighten out If possible the two lines should be straight On some CRT the lines may not straighten even if you turn the contrast to its minimum If this is the case slowly increase the contrast to a point just before the vertical lines have extreme bending You have now properly set up the contrast of your display Continue to set up brightness as detailed above The Color8 Bars75
28. d presets as follows Customize the aspect ratio manually refer to Setting the Input Aspect Ratio Manually above Select one of the presets from the Save User To menu Confirm the action by selecting Yes Be careful because saving to a preset deletes the previous preset If you have not customized the aspect ratio and the current aspect ratio settings are the same as a system defined preset In this case the system will not allow you to save the preset setting Front Panel and On Screen Displays for IAR The On Screen Display OSD and the Front Panel Display FPD allow you to set the Input Aspect Ratio 4 3 Input Adjust Control Push the Input Adjust button once to show the current input adjustment function You can cycle through the available functions by pushing this button repeatedly The available input adjust functions are as follows Overscan Deinterlacing Pass Through Line Offset Color Space Input Level VCR mode Film mode HDCP Mode Auto Priority Audio Input AV Lip Sync Overscan The Overscan function scales the input image proportionally in both vertical and horizontal dimensions by the user specified overscan factor The purpose of Overscan is to remove unwanted image portions around the perimeter of the image The default overscan value is 0 which means 100 of the input image is shown The maximum overscan value is 20 which means the input image is scaled up by 120 T
29. d to the external power supply 2 Plug the removable power cord into a wall outlet or power conditioner if applicable 3 Plug the small connector attached to the cable that comes out of the power supply into the Master Two The Master Two should power on and display CineVERSUM Powered by ABT on the FPD STEP 2 Connect the to your system Displays with a DVI or HDMI Input The default output on the Master Two is digital RGB 4 4 4 DVI Standard If you have changed this setting follow these instructions to change the settings back 1 Press the Menu button on the front panel of the Master Two once You should see Main Menu Input Select on the FPD 2 Press the Up button once You should see Main Menu Output Setup on the FPD 3 Press the Enter button You should see Output Setup Analog Digital on the FPD 4 Press the Enter button You should see Analog Digital BNC Analog 5 Press the Down button to select HDMI Digital and press the Enter button You should see the Master Two s On Screen Display OSD on your screen Displays with a Component YPbPr Input 1 Press the Menu button on the front panel of the Master Two once You should see 2 Main Menu Input Select on the FPD 3 Press the Up button once You should see Main Menu Output Setup on the FPD 4 Press the Enter button You should see Output Setup Analog Digital on the FPD 5 Press the Enter button You should see Analog Digital BNC
30. ding on your display Using the Output Format 1080p60 with a Video Signal at 50Hz can lead to a wrong decoding by your display To obtain a clear picture do as follow Change the Output Format to 1080p50 Output Setup gt Format gt 1080p50 S8011030 Master Two User Manual 5 0 APPENDIX The Output Signal sent to your display would have a frame rate of 50Hz using the 1080p50 Output Format or Change the Frame rate from 50Hz to 60 Hz Output Setup gt Frame Rate gt 50Hz gt Unlock and change the value to 59 95 by using the Up button The Output Signal sent to your display would have a 59 94Hz frame rate using the 1080p60 Output Format The picture is green when I use the analog output of the Master Two A green picture usually means that a component video signal is being sent to the RGBHV input of a display Follow the instructions earlier in the user guide to setup your Master Two to work with a display with RGBHV inputs No picture when I connect the Master Two to the HDMI input of my display The default output from the Master Two is digital RGB 4 4 4 DVI Standard Make sure that the display that you are connected to is HDCP compliant The Blue status LED blinks on the front panel of the Master Two A blinking blue light on the Master Two means that the scaler is processing an HDCP protected signal but is unable to authenticate with the display Verify that your display is HDCP compliant If it is not HDCP complian
31. dividual sources and your display To learn more about how to use the internal test patterns refer to the section Setting up an Master Two Using the Internal Test Patterns and Avia Guide to Home Theater Calibration DVD To turn the test patterns on and off use the Test Pattern On Off button To navigate backwards and forwards through the available test patterns use the and buttons respectively Auto Standby The default setting is Off which means Master Two is always in Active mode regardless of the activity state of the selected input If Auto Standby is On the Master Two goes into Standby mode 30 seconds after the selected input becomes inactive To see the current setting press Up or Down Then press the same button again to change the setting S8011030 Master Two User Manual 4 0 MENU OPTIONS LED Brightness This selection allows the user to configure the behavior of the Front Panel LED brightness The Active parameter adjusts the brightness of the Front Panel LED when the menu is being navigated The Reduced parameter adjusts the brightness of the Front Panel LED during normal usage when the menu is not being navigated User Mode You have limited access to the output timing controls in Normal mode In Advanced user mode you have access to the complete set of output timing controls Push the Down button to see the current setting and the FPD displays either Normal or Advanced user level Push the
32. djust the Brightness press the Picture Control button and then using the up down arrow buttons highlight Brightness and press enter to adjust the setting If you were changing this value to 5 the abbreviated instructions would read as follows Picture Control gt Brightness gt 5 1 3 Unpacking and Inspection Your Master Two carton should contain the following items Master Two Video Processor Universal 6V 95A AC to DC Power Converter Power Cord Remote Control Master Two User Manual S8011030 Master Two User Manual 2 0 25 5 1 0 GETTING STARTED 1 4 Serial Cable for Software Updates and Automation 1 1 The Master Two uses BNC style analog connectors and an HDMI digital connector to provide video output signals You must purchase an output cable to connect to one of these outputs to your display Different displays have different input connectors so check your display specifications to ensure compatibility Both input and output cables can be supplied by your Authorized CineVERSUM Reseller To find your nearest Authorized CineVERSUM Reseller go to www cineversum com Display Compatibility Requirements 1 5 Master Two video processing product is compatible with a wide range of displays These include digital TVs projectors and flat panel displays as well as other emerging technologies that can support 480p or higher resolution video signals To determine if your display is compatible with th
33. e Control Overview Do not attempt to use the remote control out of line of sight with the IR receiver Doing so will cause improper operation S8011030 Master Two User Manual Jy 7 2 0 BASIC OPERATION 2 0 BASIC OPERATION 2 1 Front Panel Overview Front Panel Display FPD Adjustment Buttons Menu Up Exit C2 Cineversum MASTER Two On Standby Left Down Right Status LED This displays the current state of the Master Two Off The unit is in standby mode Red No signal detected Blue The unit is processing the signal Green The unit detects an unsupported signal On Standby This toggles unit power between On and Standby IR Window This is where all IR commands are received by the Master Two Do not obstruct this window Front Panel Display FPD This is where all information from the on screen display OSD is duplicated to assist in the setup of your Master Two en navigating the the always shows the current selection on the bottom line and the menu submenu item on the top line When you change a value of a setting the value is on the bottom line and the title of the parameter is on the top line Navigation Keys These keys are duplicated on the remote control and function exactly the same Switching Inputs using the Navigation keys You can switch inputs on the front panel of the Master Two using the navigation keys v and To do this press the Down or Up without pressing the Menu button fi
34. e Master Two look to see if it has one of the inputs listed below If not then your display is probably limited to receive a standard NTSC PAL or SECAM interlaced signal and will not function correctly with the Master Two Digital Inputs en HDMI input DVI D input Analog Inputs Pec Or B L u 9 e CA 5 BN Component Inputs YCbCr or YPbPr or Component video inputs that are not capable of accepting a 480p signal should be labeled 480i NTSC or 576i PAL SECAM The following types of displays should be compatible with the Master Two since it can support higher resolution signals Plasma displays LCD based flat panel and front amp rear projection displays DLP based front amp rear projection displays D ILA based front amp rear projection displays SXRD included CRT based Direct View HDTVs and Computer Monitors with front and rear projection displays Installation Guidelines Take special care with the Master Two installation to ensure optimal performance Pay particular attention to the bulleted items that begin below and to other precautions that appear throughout this guide Do Install the Master Two on a solid flat level surface such as a table or shelf You can also install the Master Two in a standard 19 equipment rack using an optional rack mount kit available from authorized CineVERSUM resellers or directly from CineVERSUM Select a dry well vent
35. ent 2 Audio 4 S Video 1 Audio 2 S Video 2 Audio 3 Video 1 Analog Video 2 Off HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3 HDMI 4 HDMI 4 SDI Off RGBHV Component Off Software Update To install the latest software for your Master Two please follow the procedure described below 1 Set the communication speed to 57600 bps in the serial baud rate menu 2 Connect the Master Two to your computer with the RS 232 cable 3 Change the software update value to Yes to begin the update process The upgrade procedure is fully detailed in the Software Update Procedure for Master Two manual Information This setting shows information about the system including Input Status Video Source Signal Type Audio Source Aspect Ratio Frame Active Output Status Resolution Color Space Frame Rate Line Rate Aspect Ratio Display Screen This screen can be helpful during troubleshooting 4 6 Output Setup 26 Analog Digital A D Push the Down button to show the current output type Push the Down button again to select the next item on the list shown below You can also use the Up button to cycle through the output types Analog Output BNC style connectors Digital Output HDMI connector Output Format S8011030 Master Two User Manual 4 0 MENU OPTIONS Push the Down to show the current output format Push the Down button again to show the next item on the list shown in Table 5 You
36. h the available aspect ratios Push the Exit button to exit the menu and go back to the Input Aspect Ratio selection For the Zoom Pan and Borders functions push the Up or Down button to select the two control settings available horizontal and vertical Push the Enter button to adjust each setting Push Up and Down to increase or decrease the setting Push Exit again to exit this mode Note The Zoom and Pan functions are applied to the input signal not the output This is an important consideration especially for the Pan function For example If you do not zoom a full frame image more than 100 there is nothing to pan However if part of the image is not on the screen then the Pan function will work The Master Two s menu is exit automatically after 30 seconds of no user interaction Video input signals are usually classified in the following two ways Frame Aspect Ratio Active Input Aspect Ratio Frame Aspect Ratio S8011030 Master Two User Manual 4 0 MENU OPTIONS Frame Aspect Ratio FAR consists of two possible ratios 4 3 or 16 9 DVD discs encoded in a 16 9 frame are sometimes referred to as anamorphic or enhanced for widescreen TV s For example a non anamorphic widescreen DVD has a FAR of 4 3 Active Aspect Ratio Active Aspect Ratio AAR is the aspect ratio of the image or content movie This content is typically stated on the back cover of DVD discs Some common active aspect ratios are as follows 1 33 1
37. he Input AR menu for doing this with the OSD The remote control operation is described below 4 3 Selects 4 3 Full Frame without OSD 16 9 Selects 16 9 Full Frame without OSD Pushing the Input Aspect Ratio button repeatedly selects Preset 1 through Preset 10 and User in sequence without using the On Screen Display OSD The ten user defined preset value selections Preset 1 10 are stored in non volatile memory and always available Each of these presets consists of the following Frame Aspect Ratio Active Input Aspect Ratio Zoom parameter Pan parameter Borders S8011030 Master Two User Manual 4 0 MENU OPTIONS The User preset selection is also stored in non volatile memory However the User selection is always updated after you modify any pre defined aspect ratio setting In order to permanently keep a custom aspect ratio setting you must save it to one of the four preset selections Setting the Input Aspect Ratio Manually You can set the following parameters manually Frame Aspect Ratio Active Input Aspect Ratio Zoom factor Pan parameter Borders horizontal and vertical Typically you only need to select the Frame Aspect Ratio and Active Input Aspect Ratio to get an acceptable picture The Active Input Aspect Ratio menu item lists the most common movie aspect ratios 1 33 1 1 85 1 and 2 35 1 You can also customize the Input Aspect Ratio using the Up and Down buttons Save User define
38. hooting 38 My Master Two shows an error message If the Master Two does not boot correctly you may get an error message Performing a hard reset of the Master Two should clear any memory errors and reboot the unit to its factory default 480p digital RGB 4 4 4 output If you still get an error message after performing a hard reset contact our distributor for service Perform a hard reset of the Master Two unit using the remote control as follows 1 Press the Configuration button on the remote until the Front Panel Display FPD reads Configuration Factory Default 2 Press Enter The FPD indicates No 3 Press the up arrow The FPD indicates Yes 4 Press Enter The Master Two reboots to its factory default Perform a hard reset of the Master Two unit using the remote control as follows Press the Configuration button on the remote until the front LED reads FCTD Press Enter The FPD indicates NO Press the up arrow The FPD indicates YES Press Enter Master Two reboots to its factory default Perform a hard reset of the Master Two unit using the buttons on the front panel as follows 1 Unplug the power supply from the Master Two unit 2 Press Menu and Exit buttons simultaneously while plugging the power back in The picture has horizontal lines with the Output set to 1080p60 or 720p60 The Output Format 1080p60 is defined by SMPTE 274M standard to match a Video Output at 60 frames per second or 59 94Hz depen
39. iagonal HDTV Compatibility 540p 1080i This display only displays two resolutions both of which the Master Two can output To find out which one looks best on your display use familiar material like a favorite DVD to compare to find out which resolution is more to your liking on your display Below are several different popular display technologies and their most likely native resolutions Plasma 42 43 852x480 1024x768 1024x1024 1024x1080 50 63 1280x768 1360x768 1366x768 1920x1080 DLP Rear Projection 1280x720 720p 1920x1080 1080p Front Projection 852x480 1024x768 1280x720 720p 1280x768 1920x1080 1080p LCD Rear Projection 1280x720 720p 1366x768 1920x1080 1080p Front Projection 1024x768 1280x720 720p 1366x768 Direct View 1024x768 1280x720 720p 1366x768 1920x1080 1080p LCoS Rear Projection 1280x720 720p 1366x768 1920x1080 1080p Front Projection 1280x720 720p 1920x1080 1080p CRT Rear Projection 480p 540p 1080i Front Projection 1280x720 720p 1280x960 1440x960 1440x1152 1920x1080 1080p Initial Setup of the to Your Display Test Patterns used Frame Geometry Checker board Vertical Lines Horizontal Lines Judder The following information uses a Fujitsu 50 plasma Model P50XHA10US as an example This display has an actual native resolution of 1360x768 1 Select the preset which is closest to the output resolution that you need
40. iew iii enne nene nnne nnne inneren nnns 9 Power Standby Buttons 2 ininemier needed 10 Curtain Button 10 Remote Control Battery Installation sse sees eee eee ee eee eee eee 10 W L aT eT Tor pm 10 TU RES AE Re 11 Power Supply Input iii 11 3 0 SETUP nn nine een meta dre et anne t C den eee it 12 3 4 Initial Set Up HI 12 STEP 1 4 Power Up iiti io tree nn dinde EE be Pea EORR 12 STEP 2 Connect the to your system 12 STEP 3 Connecting Your Sources to the Master TWO sse eee eee eee 13 3 2 Audio Operation sise 17 LEOMM Rerum 18 4 nputSelecla de eei d te E rb pra parere ended S BR ERR IRL RD Kad ex einen ane Rn 18 4 2 Input Aspect Ratio Control sisi 18 Frame Aspect RAO M nm tentes 18 Active Aspect 0 e enter A anne t einen lee 19 Master Two Image Mapping sissies viessennetsavansexnvecastasavdeattanseduenthgaasdiee aaa ani 19 laete EE 20 Zee M M CLS 20 RES 0 RER EREE ES E n rond s lee dr Ner E LCD E 20 BOR CONS RED 20 STE cscs ERIS 20 Front Panel and On Screen Displays for IAR sese seene 21 4 3 Inp tAdjust Conttol terre dense jeanedeeneastecs E cee ane am ae uter Eus era eee 21 OVENS CAM EL Ee 21 rcgem ETE 22 PASS TON ET 22 LING e Re RPM 22 Color SPACE EE 22 feu EE 22 VCRIMOdE x 22 Film WO GG c THEE 22 HDMI CONTIQ E 23 Auto Input Priority Selection 23 Adio MPU ersed PC eu aneebawemenealis 23
41. ilated location Use only the included external power supply Avoid excessive humidity sudden temperature changes or temperature extremes S8011030 Master Two User Manual 1 0 GETTING STARTED Use only accessories recommended by the manufacturer to avoid fire shock or other hazards Unplug your Master Two before cleaning Use a damp cloth for cleaning Don t Install the Master Two on an unstable surface or one that is unable to support all four of its feet unless it is installed in an equipment rack Stack the Master Two directly above heat producing equipment such as power amplifiers or other components that generate heat during use Expose the Master Two to a high temperatures humidity steam smoke dampness or excessive dust Avoid installing the Master Two near radiators and other heat producing appliances Install the Master Two near unshielded TV or FM antennas cable TV decoders and other RF emitting devices that might cause interference Place the Master Two on a thick rug or carpet or cover the Master Two with cloth This might prevent proper cooling Attempt to service this unit Instead disconnect it and contact your Authorized CineVERSUM Reseller Open or remove unit panels or make any adjustments not described in this manual Attempting to do so could expose you to dangerous electrical shock or other hazards It may also cause damage to your Master Two Obstruct the front panel IR receiver window shown in Remot
42. indow IRE70 Window IRE80 Window IRE90 Window IRE100 IRE IRE stands for International Radio Engineers and it is a relative scale It defines the volt peak to peak video divided up into 140 IRE units This is done to make numbers for luminance levels easier to communicate In the ISF Training Manual it is described as the amplitude of the video signal from blanking zero volts to peak white is 0 714286 volts or 100 IRE units Synchronization signals extend from blanking to 0 285714 volts or 40 IRE units CRT Display Calibration To get the best picture from your CRT based display make sure that the red blue and green signals are converged properly To assist in converging these three signals the Master Two has two test patterns In addition to convergence make sure that the focus is optimally adjusted Another test pattern has been included specifically designed for this application On some displays these settings may not be available unless you get into the service menu CineVERSUM recommends that you hire an certified technician to make these adjustments if you do not feel comfortable getting into the service menu Test Patterns Used XHatch Coarse XHatch Fine Focus Source Calibration Test Patterns Used Half Black White H Clr7 Bars75 H Clr7 Bars100 H Clr8 Bars75 H CIt8 Bars100 To get the best performance out of each of your sources you should individually calibrate each input specifically to the connected source In thi
43. is selected the HDMI option will not be available S8011030 Master Two User Manual L2 20 17 4 0 MENU OPTIONS 4 0 MENU OPTIONS 4 1 4 2 Input Select There are twelve available inputs on the Master Two VIDEO 1 Video 1 Composite VIDEO 2 Video 2 Composite S VIDEO 1 S Video 1 S VIDEO 2 S Video 2 COMPONENT 1 Component RGBs 1 COMPONENT 2 Component RGBs 2 RGBHV RGBHV Component HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3 HDMI 4 HDMI 4 AUTO Automatic active input detection and selection SDI SD SDI SDI Video Input Module required These inputs can be accessed in five different ways Using the front panel using the Left and Right buttons Using the remote control with the direct access buttons Using a universal remote programmed with the discrete codes Using the OSD from the front panel or from the remote to access the Input Select menu Using RS232 Serial Automation Protocol described in the appendix Input Aspect Ratio Control 18 The Input Aspect Ratio control selects the aspect ratio for the current input signal The Master Two automatically converts from the selected input aspect ratio to the selected output aspect ratio Push the Aspect button once to show the current input aspect ratio control function To cycle through the available functions push the Aspect button repeatedly For the Input AR function push the Up or Down button once to show the current setting Push either of these buttons again to cycle throug
44. issioned operated incorrectly or if after the transfer of risks the goods are subject to influences not agreed upon in the contract all guarantee claims of the purchaser will be rendered invalid Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser e g interfaces Normal wear as well as normal maintenance are not subject to the guarantee provided by CineVERSUM either The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer Trademarks Brand and product names mentioned in this manual may be trademarks registered trademarks or copyrights of their respective holders All brands and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products of their manufactures S8011030 Master Two User Manual TABLE OF CONTENTS 1 0 GETTING STARTED 1 1 Introduction 1 2 Document Conventions 1 3 Unpacking and Inspection sisi 5 1 4 Display Compatibility Requirements ss 6 1 5 Installation Guidelines 2 0 BASIC OPERATION 2 1 Front Panel Overview 2 2 Rear Panel Overview Kie sae ecc Video Outputs PUIG MN i c EET Audio Outputs 2 3 Remote Control Overv
45. l 25Hz frames 3 times You can also set the output frame rate to a specific value unlocked mode For 60Hz sources if the original source material is progressive at 24Hz uses 3 2 pull down the output frame can be source locked to either 48Hz 60Hz or 72Hz The 48Hz setting repeats each original 24Hz frame 2 times while the 72Hz setting repeats each frame 3 times As with 50Hz sources you can also set the output frame rate to a specific value unlocked mode Press the Up or Down button once to see the current input rate Press the same button again to switch input rate 50 50Hz input sources 60 gt 60Hz input sources Press the Enter button to select the input frame rate and change the output frame rate settings Select the desired output frame rate setting by using the Up or Down button For 50 Hz input sources the available settings are 50Hz Lock source locked 50Hz 75Hz Lock source locked 75Hz Unlock unlocked For 60 Hz input sources the available settings are 48Hz Lock source locked 48Hz 60Hz Lock source locked 60Hz 72Hz Lock source locked 72Hz Unlock unlocked If you chose Unlock press the Enter button again to specify the desired output frame rate Use the Up or Down button to increase or decrease the frame rate Press the Output Select button again to exit the menu and complete the output frame rate conversion setting Border Level The border level setting is global that is there is only
46. l benefit of skipping an extra digital to analog D to A and analog to digital A to D step for a picture with even more detail then a component connection With a component connection set the player s output to 480i minimizing the amount of processing done in the player S8011030 Master Two User Manual 3 0 SETUP High Definition Set Top Box or DVR D VHS High Definition Set Top Box or DVR D VHS COAXIAL EE Coaxial AUDIO DVI D OUT HDCP HDMI OUT COMPONENT OUT Optical Audio Component ANALOG VIDEO Back of Master Two Note Some set top boxes require you to switch the output resolution This means that if you are watching an HD channel you must manually switch the output resolution to 720p 1080i p or if you are watching an SD channel you must manually switch the output resolution to 480i or 480p 480i preferably If your display only has component or RGBHV inputs use the component output from your HD source S8011030 Master Two User Manual 2 5 3 0 SETUP Game Console Game Console Proprietary HDTV Optical Audio AV Pack Back of Master Two Set the game console to output the highest resolution available to get the best results Personal Computer Personal Computer AUDIO OPTICAL COAXIAL 9 g DVI HDCP
47. nt RGBS 1 576p PAL SECAM 9 Component RGBS 1 720p ATSC 10 Component RGBS 1 1080i ATSC 11 Component RGBS 2 480i NTSC 12 Component RGBS 2 576i PAL SECAM 13 Component RGBS 2 480p NTSC 14 Component RGBS 2 576p PAL SECAM 15 Component RGBS 2 720p ATSC 16 Component RGBS 2 1080i ATSC 17 RGBHV Component 480p NTSC 18 RGBHV Component 576p PAL SECAM 19 RGBHV Component 720p ATSC 20 RGBHV Component 1080i ATSC 21 RGBHV Component VGA 22 RGBHV Component SVGA 23 RGBHV Component XGA S8011030 Master Two User Manual Table 3 Input Format Settings 31 5 0 APPENDIX 32 24 RGBHV Component SXGA 25 SDI 480i NTSC 26 SDI 576i PAL SECAM 27 HDMI 1 480i NTSC 28 HDMI 1 576i PAL SECAM 29 HDMI 1 480p NTSC 30 HDMI 1 576p PAL SECAM 31 HDMI 1 720p ATSC 32 HDMI 1 1080i ATSC 33 HDMI 1 VGA 34 HDMI 1 SVGA 35 HDMI 1 XGA 36 HDMI 1 SXGA 37 HDMI 2 480i NTSC 38 HDMI 2 576i PAL SECAM 39 HDMI 2 480p NTSC 40 HDMI 2 576p PAL SECAM 41 HDMI 2 720p ATSC 42 HDMI 2 1080i ATSC 43 HDMI 2 VGA 44 HDMI 2 SVGA 45 HDMI 2 XGA 46 HDMI 2 SXGA 47 HDMI 3 480i NTSC 48 HDMI 3 576i PAL SECAM 49 HDMI 3 480p NTSC 50 HDMI 3 576p PAL SECAM 51 HDMI 3 720p ATSC 52 HDMI 3 1080i ATSC 53 HDMI 3 VGA 54 HDMI 3 SVGA 55 HDMI 3 XGA 56 HDMI 3 SXGA 57 HDMI 4 480i NTSC 58 HDMI 4 576i PAL SECAM 59 HDMI 4 480p NTSC
48. nto the DC In port on the back of the Master Two The Master Two should power on and display CineVERSUM Powered by ABT on the FPD for a couple of seconds Use only the power supply that came with your Master Two S8011030 Master Two User Manual 2 l 3 0 SETUP 3 0 SETUP 3 1 Initial Set Up 12 Once you have installed the Master Two into your system you must properly configure it for the display device being driven The Master Two is shipped from the factory with the following preset default settings Input Select is set to AUTO to automatically detect an active input in a pre configured priority The Digital Video output is selected with RGB 4 4 4 color space The output format is set to SMPTE 274M 1080p Use either the remote control or the front panel controls to perform the initial setup of the Master Two s output The procedure below uses the front panel buttons to perform initial setup Accessing the Master Two s OSD is crucial not only in allowing you to navigate the menu of the Master Two but also to let you know that the Master Two is sending a compatible signal to the display If the OSD is not visible on the display s screen when you press one of the sub menu buttons on the remote control then you must configure the Master Two with the Output Setup menu to output a signal that the display can accept Use these steps to allow you to see the OSD STEP 1 Power Up 1 Attach the removable power cor
49. o adjust the overscan level 1 Push the Up or Down button The current level is shown S8011030 Master Two User Manual 2 Jm 2 4 0 MENU OPTIONS 22 2 Push the Up or Down button to decrease or increase the amount of overscan The Overscan value is applied to all input aspect ratios and is independent of the Zoom value Deinterlacing This sub menu is available when the Precision Deinterlacing Card 87021030 is installed and if an interlaced video source PAL or NTSC is detected Then you can choose between seven different deinterlacing methods that better suits your need Auto Film Bias Mode Video Mode 2 2 Even 2 2 Odd Game Mode 1 Game Mode 2 Pass Through The Pass Through feature allows you to transmit the selected input to the Master Two output unmodified On Off Note The Pass Through function can be set by Input Source and also by resolution of its input By example if you have a High Definition Player connected to the HDMI 1 input this unit can upscale into 576p or 1080p You can set the Master Two to upscale the 576p signal to 1080p by setting the Pass Through option to Off and you can set the Master Two to Pass Through the 1080p signal When you will switch the resolution of you High Definition Player the Master Two will automatically switch the Pass Through mode from On to Off depending of the resolution detected in the HDMI 1 input Line Offset The image can be adjusted vertically when an SDI or HDMI
50. riority assignment 5 Repeat Steps 1 through 4 to select the next video input and adjust the priority setting Audio Input The Audio Input function assigns an audio input to the currently selected video input Four digital audio inputs and a single analog audio input are available To assign the audio input to another video input push the Down button The front panel display FPD shows the current setting For more info about how to assign an audio input to a video input refer to Audio Input Operation AV Lip Sync The Master Two automatically delays the input audio to match the video processing delay You can choose to increase or decrease the audio delay by changing this setting Push the Up or Down button to display the current additional bias delay setting default 0 Use the Up or Down button to increase or decrease the delay in milliseconds Note The total audio delay cannot be less than zero that is the Master Two cannot have negative audio delay If you choose to decrease the automatic delay setting by a certain amount this value could be changed by the Master Two in situations where the Master Two s calculated delay plus the specified additional delay results in a value less than Zero 4 4 Picture Controls Brightness S8011030 Master Two User Manual 22 7 23 4 0 MENU OPTIONS 4 5 This control adjusts the brightness black level of the overall image output from the Master Two If you turn it up too high it m
51. rst 2 2 Rear Panel Overview Digital Digital Audio Analog Audio Analog Video Component 1 Composite Audio Out Inputs 1 2 Inputs L R SDI Input Input Sync 1 YPbPr or RGB S Video1 Video1 optical optical optical OMPONENT S VIDEO VIDEO DIGITAL AUDIO SERIAL PORT OMC SS VIDEO VIDE a enn meren HDMI Output HDMI Inputs Analog Video Power Sync2 Component 2 S Video2 Composite Digital Digital Audio Serial Port 1 2 3 4 Output YPbPr or RGB Video 2 Audio Out Inputs 3 4 coaxial coaxial Video Inputs The Master Two has eleven 11 video inputs and an optional SD SDI input available P N SDI 601A The inputs and the formats they support are as follows Video 1 NTSC PAL PAL M and SECAM Video 2 NTSC PAL PAL M and SECAM S Video 1 NTSC PAL PAL M and SECAM S Video 2 NTSC PAL PAL M and SECAM Component RGBS 1 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz Component RGBS 2 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz RGBHV Component 480p 576p 720p 50Hz 720p 260Hz 1080i 50Hz 1080i 60Hz VGA SVGA XGA S8011030 Master Two User Manual 2 0 BASIC OPERATION SXGA 60Hz HDMI 1 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz VGA SVGA XGA SXGA 60Hz RGB YCbCr 4 4 4 YCbCr 4 2 2 HDMI 2 480i p 576i p 720p 50Hz 720p 60Hz 1080i 50Hz 1080i 60Hz VGA SVGA XGA SXGA 60Hz RGB YCbCr 4 4 4 YCb
52. s The Film Bias mode may improve film mode detection in some cases For example it may improve the detection of PAL SECAM film sources Auto Source adaptive deinterlacing is on This is the preferred setting as it sets the deinterlacer to optimally process a variety of signal types and quality HDMI Config The HDMI Config menu gives access to three parameters HDCP mode Off HDCP is disabled at the Master Two s HDMI input some sources turn off HDCP in this case and the Master Two drives a non HDCP DVI display or an analog display On The Master Two continuously looks for a HDCP source on its HDMI input Auto Aspect Ratio Off The Aspect Ratio is determined by user On The Master Two reads the video aspect ratio contained into the Info Frame and applies it if available Auto Color Space Off The Color space is determined by user On The Master Two applies the Color Space specified into the Info Frame if available Auto Input Priority Selection The Auto Input Priority Selection function assigns different priorities to the video input s automatic active video selection mode AUTO in Input Select menu First select the video input then change the priority of that input 1 Press the Down button The first video input Video 1 is shown 2 Press the Enter button to view the current priority of the selected input 3 Press the Up or Down button to change the priority of the selected input 4 Press the Exit button again to complete the p
53. s CineVERSUM recommends that you use the Avia Guide to Home Theater DVD to assist in this setup Determining the Correct Output Resolution for Your Display Determine the optimum output resolution to set your Master Two to get the best picture from your display To do this correctly you must know what the native resolution or maximum resolution of your display Native resolution refers to the actual pixel count of a fixed pixel display Fixed pixel display technologies include plasma LCD DLP and LCoS CRT based technologies use scan lines so they do not have a native resolution but they do have a maximum resolution Keep in mind that some displays do not accept their native resolution The following is an example of specifications from an LCD TV Diagonal Screen Size inches 32 Display Capability 480p 720p 1080i p Aspect Ratio 16 9 Widescreen Resolution Number of Pixels 1280 x 768 1 049 088 pixels The native resolution of this display is 1280x768 which a Master Two can output but this display is only capable of accepting 480p 720p or 1080i signals For this display the best output resolution to choose on the Master Two is 720p since it is the closest to the native resolution of this display S8011030 Master Two User Manual 2 0 33 5 0 APPENDIX 34 An example of the specifications from a CRT based rear projection display is shown below Diagonal Screen Size inches 53 Aspect Ratio 16 9 Widescreen CRT Type 7 D
54. s section all picture control adjustments are made using the Master Two s picture controls Keep in mind that if you replace a source with a new component you will also want to recalibrate the input To calibrate each source correctly you will need the source to output a reference test pattern similar to what is built in to the Master Two For sources like DVD LD and D VHS this content is readily available But for a source like HD satellite or cable these test patterns are played on channels like HDNet at off hours So if you have a DVR CineVERSUM recommends that you record these test patterns AVIA will assist in setting up the input to which your DVD player is connected Cine VERSUM recommends that you use a digital connection DVI HDMI or SDI or a high quality analog connection component video Don t use S Video or Composite video for a higher quality source like DVD Before calibrating the input for your DVD player S8011030 Master Two User Manual __ 87 5 0 APPENDIX make sure that your DVD player is set to 16 9 output not 4 3 You will also want to turn off any extraneous features like noise reduction which may add more noise than help Set all picture settings on the DVD player to either Off default or 0 Use the test patterns included on the AVIA DVD to adjust the picture controls on this input If you are not familiar with how to make these adjustments watch the guided setup first and then
55. synchronization signal type of the output format Press the Up or Down button to show the current sync type Press the same button again to move to the next synctype Currently the Master Two supports seven sync types Bi evel bi level sync on green luma Tri level tri level sync on green luma CSync Composite Sync on the H sync BNC connector H V Positive Hsync and Positive Vsync H V Positive Hsync and Negative Vsync H V Negative Hsync and Positive Vsync H V Negative Hsync and Negative Vsync S8011030 Master Two User Manual 4 0 MENU OPTIONS Color Space The color space parameter sets the color space of the output format Press the Up or Down button to show the current color space Press the same button again to select the alternate color space Two analog color space options are supported YPbPr default and RGB Two digital color space options are supported RGB default and YCbCr both 4 2 2 and 4 4 4 Output Level The output level setting allows the user to specify the levels of the output signal either Video 16 235 or PC 0 255 Video PC Framerate Conversion This parameter enables framerate conversion There are two sets of controls one for 50Hz input sources and one for 60Hz input sources For 50Hz sources if the original source material is progressive at 25Hz uses 2 2 pull down the output framerate can be source locked at either 50Hz or 75Hz The 75Hz setting repeats each of the origina
56. t Vertical Size Vertical Front Porch Vertical Sync Vertical Back Porch Vertical Total Aspect Ratio Display 4 3 5 4 16 9 2 35 1 User Range 1 00 3 00 Screen 4 3 16 9 2 35 1 User Range 1 00 3 00 Image Shift Vertical Range 30 30 Horizontal Range 30 30 Underscan Range 0 100 Sync Type Bi Level Tri Level Table 5 Complete Menu Tree S8011030 Master Two User Manual 2 43 5 0 APPENDIX Composite H V H V H V H V Color Space RGB YPbPr YCbCr 4 2 2 YCbCr 4 4 4 Output Level PC Video Framerate 50 Hz 50 Hz Lock 75 Hz Lock Unlock Range 25 120 60 Hz 48 Hz Lock 60 Hz Lock 72 Hz Lock Unlock Range 24 120 Border Level Range 0 100 Gamma Correction OFF ON Range 0 50 2 50 HDCP Mode OFF ON Display Profile Select User Profile 1 Profile 2 Profile 10 Save Profile 1 No Yes Profile 2 No Yes Profile 10 No Yes Auto OFF ON 44 Table 5 Complete Menu Tree S8011030 Master Two User Manual Contact Information TEC CineVERSUM 7 rue La Caille 75017 Paris France E mail info cineversum com www cineversum com Part No S8011030 VERSUM
57. t use component connections If the display is compliant then verify that the HDCP mode is set to On in the Input Adjust and Output Setup menus If the problem persists check the cabling and try new cables if possible or try cycling the power on your display or HDCP source The Green status LED blinks on the front panel of the Master Two The LED on the Master Two blinks green when it is passing a copy protected signal to a non HDCP display If your display is not HDCP compliant then the image won t be displayed Use component connections from your source to your Master Two instead Will lose the settings on my Master Two if update the software version Currently the Master Two may lose its settings when a software update is performed Take note of your output settings before updating the software version on your unit Complete Menu Tree Input Select Video 1 Video 2 S Video 1 S Video 2 Component 1 Component 2 RGBHV Component HDMI 1 HDMI 2 HDMI 3 HDMI 4 SDI SDI Input Module S7011030 is required Auto Input Aspect Ratio Frame AR 4 3 16 9 Active AR 1 33 1 1 55 1 1 66 1 1 78 1 Table 5 Complete Menu Tree S8011030 Master Two User Manual 39 5 0 APPENDIX 1 85 1 2 35 1 User Panorama ON OFF Zoom Horizontal Range 0 100 Vertical Range 0 100 Pan Horizontal Range 0 100 Vertical Range 0 100 Borders Hori
58. t Setup gt Format gt 1366x768 gt H Shift gt Range Output Setup gt Format gt 1366x768 gt V Shift gt Range Any adjustments made to the output format change your selected output from the resolution you selected to User This allows you to adjust the output without affecting the default settings There are three test patterns used to verify that the chosen output resolution is the native resolution of your display and that you are bypassing any internal processing in your display They are the checkerboard vertical lines and horizontal lines test patterns When the checkerboard test pattern is displayed correctly close up you should be able to see a 1 pixel checkerboard and at proper viewing distance the image should appear as an even gray If your display is CRT based you will not see this checkerboard but your screen should be an even gray When this test pattern is displayed incorrectly the resulting image does not look like a fine checkerboard and may have irregular patterns When this is the case the chosen output resolution may not be the native resolution of your display or your display may scale all input signals even if the input resolution is already at native resolution Check to make sure that the output resolution selected on the Master Two is the correct output resolution for your display If this test pattern does not appear as it should and you have chosen the native resolution of your display you may
59. the old batteries if applicable Menu Navigation You can control the Master Two as follows From the front panel controls From the Master Two remote control 10 LLL 8011030 Master Two User Manual 2 0 BASIC OPERATION From a programmed universal remote control Using the serial connection on the back panel The menu navigation controls on the remote control are duplicated on the front panel of the Master Two To navigate the menu 1 Press the Menu button 2 Use the directional buttons to highlight the parameter you want to change 3 Press the Enter button to select the parameter and the Left and Right arrow buttons to change the chosen parameter 4 Press the Exit button to exit out of the menu OSD Info Screen Press the Info button to display a window that shows information about the system including Input Status Video Source Signal Type Audio Source Aspect Ratio Frame Active Output Status Resolution Frame Rate Line Rate Aspect Ratio Display Screen This screen can be helpful during troubleshooting Power Supply Input The Master Two comes with a 6V 5A AC to DC converter power supply which accepts 100 240 VAC at 50 60Hz To attach power to the unit 1 Attach the removable power cord to the external power supply 2 Plug the removable power cord into a wall outlet or power conditioner if applicable 3 Plug the small connector attached to the cable that comes out of the power supply i
60. u The factory default values for the ten display profiles and User are as follows Output Type Digital Format 1080p Output Aspect Ratio 16 9 Active Output AR 16 9 Sync Type H V Color Space RGB 4 4 4 Output Level PC Frame Rate 50Hz and 60Hz input sources locked Border Level 0 HDCP Mode On Selecting and Saving a Display Profile Use the following procedure to select and save a display profile 1 Set up the profile by making changes to the output setup menu items If you make custom settings such as output timing parameters they are saved to User 2 Save the settings to a profile by selecting Profile 1 through 10 in the Save menu and pressing Enter 3 Once the Profile is saved the Save menu is grayed out until you make changes to the profile again Auto Linking of Input and Display Profiles The Auto feature links a specific input to a display profile To enable this feature use Output Setup Display Profile Auto When you select an input format the display profile used Profile 1 through 10 or User is saved in the saved input settings When you turn Auto On the system uses a display profile based on the selected input For example suppose you choose Display Profile 1 using Video 1 input and Display Profile 2 using S Video 1 input With Auto set to On when Video 1 is the active input the system automatically uses Display Profile 1 When S Video 1 is the active input Display Profile 2 is used When Auto is Off
61. ve the left and right borders towards the middle of the image increasing the border width and cutting off the sides of the input image Push the Down button to move the left and right borders away from the image and decreases their width If there are system generated left right borders already present for example when the input aspect ratio is 4 3 and the output aspect ratio is 16 9 the border width cannot be decreased beyond the base width created by the aspect ratio conversion Vertical Border Control Push the Up button to move the top and bottom borders towards the middle of the image increasing the border height and cutting off the sides of the input image Push the Down button to move the top and bottom borders away from the image and decrease their height If there are system generated top bottom borders already present for example when the input aspect ratio is 16 9 and the output aspect ratio is 4 3 the border height cannot be decreased beyond the base height created by the aspect ratio conversion Borders are automatically added by the system when the Active Input Aspect Ratio is not the same as the Output Aspect Ratio as explained earlier in this guide However you can add more borders using the Borders menu Presets You can specify the Input Aspect Ratio by using the Presets or Manually Using Presets You can use Presets with either the OSD or the Remote Control Input Aspect Ratio button Refer to the Preset sub menu in t
62. very highest available today We are especially pleased to bring you ABT s new precision Video scaling II This technology enables precision up conversion of standard and high definition 480i p 576i p 720p 1080i p video sources and content to the native or optimum resolution of your display delivering best in class front of screen performance Available output resolutions span from VGA up to 1080p including the standard HDTV resolutions of 720p and 1080i In addition to our own video scaling technology the Master Two also offers a host of other innovative features including 4 HDMI High Definition Multimedia Interface inputs and 1 HDMI output Analog Input and Output using BNC style Connectors Flexible Digital and Analog Audio Switching Precision Audio Video Time Delay Synchronization Timebase Correction Fully Programmable Framerate Conversion Input and Output Aspect Ratio Controls Flexible Zoom and Pan Controls SDI Input Capability with the Master Two SDI Input Module S7011030 This Owner s Manual can help you set up your new Master Two and give you the information required to match it to your display It can also show you how to connect it to and use it with the other components in your system 1 2 Document Conventions In this Owner s Manual the menu structure is referred to in the following abbreviated form Brightness Contrast Saturation Y C Delay Navigating the On Screen Display For example to a
63. zontal Range 0 200 Vertical Range 0 200 Preset 4 3 Full Frame LetterBox 16 9 Full Frame 4 3 Stretch Preset 1 Preset 2 Preset 10 User Save User To Preset 1 No Yes Preset 2 No Yes Preset 10 No Yes Input Adjust Overscan Range 0 20 Deinterlacing Precision Deinterlacing Card 87021030 is required Auto Film Bias Mode Video Mode 2 2 Even 2 2 Odd Game Mode 1 Game Mode 2 Pass Through OFF ON Line Offset Range 0 30 Color Space RGB YPbPr YCbCr 4 2 2 YCbCr 4 4 4 Auto Input Level Table 5 Complete Menu Tree 40 LLL 88011030 Master Two User Manual 5 0 APPENDIX PC Video VCR Mode ON OFF Auto Film Mode OFF Film Bias Auto HDMI Config HDCP Mode OFF ON Auto Aspect Ratio OFF ON Auto Color Space OFF ON Auto Priority Range 1 12 OFF Audio Input OFF Audio 1 Audio 2 Audio 3 Audio 4 Stereo HDMI AV Lipsync Range 0 200 Picture Control Brightness Range 50 50 Contrast Range 50 50 Saturation Range 50 50 Hue Range 50 50 Sharpness Range 0 7 Y C Delay Range 50 50 CUE Correction OFF ON Auto Configuration Test Patterns OFF Frame Geometry Brightness Contrast Vertical Lines Horizontal Lines Judder Checkboard Color8 Bars75 Color8 Bars100 Window IRE10 Window IRE20 Window IRESO
Download Pdf Manuals
Related Search
Related Contents
Samsung WA2000A1 User Manual ワークスタイル変革・構想企画支援サービス - 日本電気 Documentation Utilisateur Apex Azerty K - Esp@don Compaq 900 Computer Monitor User Manual Copyright © All rights reserved.