User`s Manual
Contents
1. 755 10 command 0755 area code Max 5 numbers use instead if area code is less than 5 digits 6 Setting IP numbers GSM amp PSTN FWT 8848 User s Manual Version 1 1 05 17911 05 command 17911 IP numbers Max 5 numbers use instead if IP number is less than 5 digit 7 Hide Caller ID been sent out Setting 1 3 01 13 command 01 value Max 02 Min 00 Default setting is 00 00 presentation indicator is used according to the subscription of the CLIR service 01 CLIR allowed 02 CLIR prohibited Notice This Setting needs GSM carrier support 8 Bar incoming call setting 14 00 14 command 00 value 00 no barring 01 set barring default setting 00 9 FSK setting optional should confirm before order 17 00 setting caller ID 17 order 00 value OO DTMF 01 FSK default setting is 00 This setting need terminal has FSK Chip set support 10 Billing Mode setting 15 00 15 command 00 value 01 reversal polarity 02 12 KHz 03 16 KHz default setting 01 11 IMEI change Setting for Quad Band M10 Module only 1 Write IMEI to RAM 18 IMEIl no 18 command IMEI No 15 digit IMEI no 2 Check IMEI if it is right and then write it to module 19 IMEI no 19 command IMEI No 15 digits IMEI No Notice Step 1 and Step 2 IMEI no must be same 12 Pin Lock amp Network Lock Setting optional Should confirm before order 2 PIN Lock 1 Set to open PIN code check and a2. GSM amp PSTN FWT 8848 User s Manual Version 1 1 GSM amp PSTN FWT 8848 Gateway User s Manual GSM amp PSTN FWT 8848 Version 1 1 2010 GSM amp PSTN FWT 8848 User s Manual Version 1 1 1 General Description GSM PSTN fwt with LCR has the function to choose route automatically When you dial from GSM PSTN fwt it will check the prefix no you preset into device Then it will call out through GSM or PSTN according to your presetting rules And GSM PSTN both support call in When you are in the phone call through GSM and at the same time another phone call to pstn line the caller will hear busy tone And vice versa It will dial out through GSM if you don t connect to PSTN or PSTN line is disconnected and it will dial out through PSTN if you don t insert SIM card or GSM network no signal Available GSM 900 1800Mhz dual band employing Wavecom Q2403A SIM500W module to make GSM 900 1800 1900Mhz Tri band employing Sim300z module to make GSM850 900 1800 1900Mhz Quadband employing M10 SIM540W module to make Appearance and Structure Item GSM amp PSTN FWT 8848 Remark Appearance White black Material ABS Acrylonitrile Butadiene Styrene Dimension 170mmx118mmx30mm Excluding antenna Weight 400g Weight of Main unit Power Switch Rocker switch Power Socket 12V DC input Phone interface RJ11 2 RJ 11 ports Antenna interface SMA female No 1 Power No 2 in use No 3 in talk No 4 Fr
3. efix of phone number to dial thru PSTN 21 Command 01 serial no 00 prefix no Maxium 5 digit if not enough use to substitute E g 21 01 00 set all number with prefix 00 call out through PSTN GSM amp PSTN FWT 8848 User s Manual Version 1 1 2 1 01 0755 set all number with prefix 0755 call out through PSTN Default setting 2 1401 AHH 21 02 2 HHHH 21 03 3 HHHH 21 04 4HHHHH 21 05 SHH 2 06 OfHHHT 21 O7 HHH 21 08 8 HHHH 2 1HOO OHHH 21 10 00 HHH Default setting Prefix 1 to 9 and 00 numbers call out through PSTN Other numbers call out through GSM ll Other Optional Function Setting 1 Restore to factory default setting 99 99 restore to factory default setting 2 Adjust dial interval 01 30 01 command 30 time Max 9 9 seconds Min 0 5 seconds default setting is 3 seconds If you use GSM amp PSTN FWT 8848 for connecting to VoIP gateway you can set dial interval as 0 5 second it can make PDD lt 5 sec Method 01 05 If you use GSM amp PSTN FWT 8848 for connecting telephone PBX billing device you can set dial interval as 3 seconds or 5 seconds as you like Method 01 30 set the dial interval as 3 seconds 3 Adjust Earphone Volume 02 15 02 command 15 volume Max 16 Min 1 default setting is 15 4 Adjust Mic Volume sensitivity 03 10 03 command 10 amount Max 16 Min 1 default setting is 10 5 Setting local area code 04 0
4. lephone numbers you want to call 3 On completion of dialed digits you can press to transmit the called telephone numbers If you don t dial any key for continual 3 seconds during the dialing terminal transmits called telephone numbers automatically 4 During calls if the telephone numbers is not free ones the terminal sends out anti polarity signal 5 If the calling party or called party hangs up the terminal stops sending out anti polarity signal Answering Incoming Calls When some calls are coming in if the connected telephone has the function of displaying incoming calls the telephone rings and displays the incoming telephone numbers Now users can lift the handset or press hand free to answer it GSM amp PSTN FWT 8848 User s Manual Warranty Card Version 1 1 Please fill in the blanks carefully and keep it properly as the voucher for warranty Type of Equipment GSM FWT 8848 User s name Contact with Contact Tel no Address Date of Ex works Date of Maintenance Damage Management Maintainer Sales Agent Stamp Purchasing Date
5. om left to right front LED display Battery if have No 5 7 Signal strength side view GSM amp PSTN FWT 8848 User s Manual Version 1 1 LEDs display for Signal strength Power Working Front side ey Status Talking and Battery indicator 1pcs SMA antenna connectors 2 RJ 11 output Rear side Power port and switch f 1pcs Sim card holder slots you can insert Sim Bottom side card into the slot 2 Features 1 Auto select economic route Low cost routing LCR function 2 GSM isn t ready call will be forced to dial out from PSTN 3 When not connecting to PSTN line GSM will provide the forced dial out function 4 Simple to install and easy to maintain 5 Steady module and reliable design ensures good performance 6 Provides optimized circuit directly connecting the exchange device for extensions 7 Compatible to most telephones PBX device 8 Strong signals with high gain antenna 9 Attractive plastic casing 10 SIM card supported 1 8V 3V 11 Caller ID display 12 Provides reversal polarity signal for metering 13 No noise and clear voice 14 Suitable for wide voltage range and low power consumption 15 Suitable for all kinds of weather and environment 16 RJ 11 ports 1 fxo for pstn line and 1 fxs port 17 Locking PIN network optional 3 Technical Specifications Air interface standard GSM850 1900Mhz 900 1 800Mhz phase 2 full band Frequency ranges A GSM 850 GSM 1900 I T
6. ransmission 869 2 893 8MHz I Transmission 1 930 1 990MHz li Reception 824 2 848 2MHz li Reception 1 850 1 910MHz B GSM 900 GSM 1800 I Transmission 890 915MHz I Transmission 1 710 1 785MHz li Reception 935 960MHz li Reception 1 805 1 880MHz Phone interface supply RJ 11 Phone Interface Hanging voltage 45V Picking off voltage 30mA 41mA GSM amp PSTN FWT 8848 User s Manual Version 1 1 Dialing tone Frequency 450Hz Antenna interface Antenna amplifying gt 2 5db Sensitivity lt 104DBM Transmitting power lt 3W Color White Black optional AC Adapter interface Input AC 110 240VAC 50 60Hz Output 12DC 1A AC Adapter type EU US AU British can be optional 4 Operation Circumstance Operation temperature 10c 60C Storage temperature 20C 70C Operation humidity 45 95 Atmosphere pressure 86 106Kpa Environment noise lt 60DB Transmitting Power 2W Sensitivity lt 104dbm Antenna Amplifying gt 2 5db Dialing frequency 450Hz Hanging voltage 45V Picking current 30mA 41mA 5 Packing List Name Quantity Remark GSM amp PSTN FWT 8848 1pcs Dual band or Quadband Ac adapter 1pcs AC 110 240V DC12V 1A Antenna 1pcs Magnetic Antenna with 3m cable User s Manual 1pcs English G W 0 75kg per unit 20pcs CTN 16kg CTN CTN Size 55cmX34 5cmX32 5cm 6 Installation and Connection The Condition for Installation The terminal asks for 110 220V AV power
7. supply It must be installed in the area where the GSM network can cover The strength of the signal can affect the quality of voice 1 Screw off the screws that are on the back of the terminal Insert SIM card for every Sim card holder and then tighten the screws GSM amp PSTN FWT 8848 User s Manual Version 1 1 2 Install antenna In order to ensure the quality of voice antenna must be put beyond 1 5 from the telephone and terminal 3 On end of the telephone line connects to the Phone port of the terminal the other end connects to telephone 4 Power port connects to power adapter that is connected to 110 220V AC power supply The Installation for Connecting to PSTN amp Ordinary Telephone The Sketch for connecting to PSTN And Ordinary Telephone set PSTN Line GSMIPSTN FWT 8848 Structure Draw your attention Because there are many types of ordinary telephone and their electric parameters are different In order to avoid mutual disturbance between telephone and terminal and affect voice quality The distance between telephone and terminal is 1 5m at least 7 Function Setting Before you do the following function settings Lift handset or press hands free key of telephone set then you can press the buttons according to the following instructions to finish setting you will hear 2 beeps when you finish this testify setting successfully I GSM PSTN routing setting Setting guide 21 01 00 set the pr
8. utomatic PIN lock function 07 1234 07 command 1234 the current SIM card PIN code If set successfully the device will open PIN code check and automatically change the current SIM Card into PIN on from PIN off 2 Set to close PIN code check and automatic PIN lock function 08 1234 08 command 1234 the current SIM card PIN code If set successfully the device will close PIN code check and automatic PIN lock function 3 Set to change PIN code open automatic PIN lock function 0971234 56785678 09 command 1234 the current sim card PIN code 5678 new PIN code 5678 can be any other 4 digits number suppose you can use 2009 GSM amp PSTN FWT 8848 User s Manual Version 1 1 If set successfully the device will change the current sim card PIN code as you want 5678 or the any other 4 digit PIN codes and open automatic PIN lock function 2 Network Lock 1 Set to open Network lock function 10 01234 10 command 01234 password 2 Set to close Network lock function 11 01234 11 command 01234 password 3 Set the Network codes 12 1 46003 46003 12 command 1 No Of IMSI 46003 the IMSI code for China Telecom 12 2 46000 460004 12 command 2 No Of IMSI 46000 the IMSI code for China Mobile 8 Making Calls and Answer Incoming Calls Making Calls 1 Lift the handset or press hand free key you will hear dialing tone then you can dial the telephone numbers you want to call 2 Dialing dialing the te
Download Pdf Manuals
Related Search