020-000663-02_LIT MAN USR Q Series ISG
Contents
1. signal can be used Input the same signal to the two projectors individually 23 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHRISTIE 5 Setting input ports using menu 5 1 Preparing for menu operations If Simple Stack without an RS 232C connection is used press the button corresponding to the port on the remote control or the INPUT button on the projector to select the port to which the cable is connected For setting of MONITOR OUT refer to SETUP menu in Operating Guide This completes the setting If Intellectual Stack with the RS 232C connection is used all settings or modifications related to Intellectual Stack menu operations must be performed on the Main projector The Main projector functions according to the input settings for Intellectual Stack 5 2 Checking Main projector s operating status For Intellectual Stack all settings or modifications related to menu operations must be performed on the Main projector Before operating the menu for Intellectual Stack check if the Main projector is functioning 4 Press the MENU button on the remote control 2 Ifthe MENU dialog as shown on the right appears on the screen the two projectors are operating in DUAL mode and the Main projector is operating Go to 5 3 Setting the menu 25 3 Use the A W lt P buttons to go into the following menu ADVANCED MENU gt OPT2. NOTES for Intellectual Stack e COMPUTER IN1 and IN2 can be used as the input port for the Main projector in Intellectual Stack Do not use other ports for image input You can input component signals to COMPUTER IN1 and IN2 You can input video signals to the Y pin of the component video of COMPUTER IN1 and IN2 NOTES for Simple Stack e COMPUTER IN1 and IN2 can be used as the input port for the projector that is connected with a computer cable at its MONITOR OUT port GOperating Guide SETUP menu If you wish to use other input ports input the image to Sub and Main individually Example of connection For DHD951 COMPUTER IN for Intellectual Stack Inputting image to Sub and Main individually 1 Split the output signal from your image device into two with device such as a signal splitter 2 Connect the output ports of the image output device to the same input ports on the Main and Sub projectors NOTES for Intellectual Stack LAN cannot be used as the input port on the Main projector in Intellectual Stack NOTES for Simple Stack Any of the ports that is compatible with the
3. CHRISTIE 3 SPACK menu settings Set the Intellectual Stack operation using the STACK menu NOTE If you are using Simple Stack without RS 232C connection skip this chapter e Read 3 5 Important information for Intellectual Stack carefully EL 79 3 1 Displaying STACK menu Use the A V lt buttons to go into the following menu ADVANCED MENU gt OPTION SERVICE COMMUNICATION STACK gt SERVICE gt COMMUNICATION gt STACK EEn STACK menu will appear on screen sien QoOperating Guide OPTION menu The setting for Intellectual Stack operation starts from this menu NOTE Check that the following settings are made on both projectors Otherwise STACK menu on the projectors cannot be operated M5 STANDBY MODE in SETUP menu NORMAL CQ Operating Guide SETUP menu COMMUNICATION TYPE under COMMUNICATION in SERVICE menu OFF Operating Guide OPTION menu STACK LOCK in SECURITY menu OFF M5 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 13 020 000663 02 Rev 1 06 2014 STACK menu settings CHKISTIE 3 2 Selecting Main Sub or off To enable Intellectual Stack select either MAIN or SUB Intellectual Stack starts when one projector is set to MAIN and the other is set to SUB in the STACK MODE dialog To disable Intellectual Stack select OFF 1 Highlight STACK MODE in the STACK menu with elles OFF the A V buttons then press the gt button to MAIN SUB di
4. SETUP menu 3 Adjust the image of Set A to fit the screen with the ZOOM FOCUS and LENS SHIFT features EQOperating Guide Adjusting the lens Adjust the image position using KEYSTONE and 3D KEYSTONE if necessary CO Operating Guide EASY MENU or SETUP menu NOTE KEYSTONE 3D KEYSTONE BLENDING or WARPING function cannot be used at the same time Please use an appropriate function e If you are using Simple Stack go to 2 3 Installation of the second projector Set B 8 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 6 020 000663 02 Rev 1 06 2014 CHAISTIE Installation 4 Display the menu with the MENU button GQOperating Guide Using the menu function 5 Use the A W lt P buttons to go into the following menu ADVANCED MENU gt OPTION SERVICE COMMUNICATION STACK gt SERVICE gt COMMUNICATION Sree OFF gt STACK RETURN STACK menu will appear on screen CO Operating Guide OPTION menu 6 Use the A V buttons to highlight STACK STACK MODE MODE and press the gt button to display ae the STACK MODE dialog SUB RETURN gt EXIT Highlight SUB pressing the A buttons and press the button After pressing the button a dialog to OO etal cana confirm whether or not to save the setting is anaes displayed Press the button to complete the setting LI 79 N ONO J YES NOTE To avoid incorrect operations with the remote control it i
5. Functions status awe On T port change e k Z i Mylmage S t f 3 1 This Schedule can be input to Projector Menu and Projector Web Control and be executed even if the projectors are operating in Intellectual Stack 2 If the input port to be changed according to the Schedule function can be used in Intellectual Stack the Schedule will be executed If not it will not be executed 3 My Image and Messenger are not executed when the projector s lamps are off 4 This Schedule can neither be input to Projector Menu and Projector Web Control nor be executed when the projectors are operating in Intellectual Stack 28 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE Restrictions on Schedule function NOTE If the Schedule is not executed an error message will be sent in accordance with the conditions set in Schedule Execution Error on Projector Web Control Network Guide 3 1 6 Alert Settings e If the Schedule function on the Main projector is set to turn on the power the projectors will be turned on according to the LAMP MODE setting e When the menu is displayed on one of the projectors the Schedule function for My Image and Messenger on the other projector will not be executed e Power Off in the table refers to turning off the power and entering the standby mode according to the Intellectual Stack settings or by pressing the STANDBY button on the remote con
6. such case a full dialog will be displayed on screen The full dialog changes to a small dialog after about 20 seconds without any key activity While the small dialog is displayed pressing the lt button displays a full dialog again The numbers 1 and 2 above the projector icons represent the Main and Sub projectors respectively Refer to the on screen messages as shown below and take the necessary actions to resolve the problem Filter Error Cold Error Small dialog DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE STACK menu settings Example Cover Error Lamp cover is opened i Cover Error Lamp Error Lamp 1 and Lamp 2 do not light Lamp Error up Lamp 1 Warning Lamp 1 does not light up SSIES Lamp 2 Warning Lamp 2 does not light up HEA Fan Error Problem with cooling fan Fan Error Temp Error Temperature of the projector is K Temp Error too high Air Flow Error Temperature of the projector is too high check that the exhaust vents are not blocked Air Flow Error Filter Error The reading on the filter timer exceeds the hours set in the FILTER 1 Filter Error MESSAGE menu MoOperating Guide OPTION menu SERVICE Cold Error The ambient temperature is too 1 Cold Error low Shutter Error Shutter does not work 1 ah Shutter Error Lens Shift Error Lens Shift does not work PERSEE Color Wheel Er
7. the Main projector is disabled when FIXED COMPUTER IN 1 is selected EQOperating Guide SETUP menu e If FIXED COMPUTER IN 1 is selected video signals can be input to the COMPUTER IN1 or IN2 port on the Main projector Set the port for video signal input in the COMPUTER IN menu and set the video format in the VIDEO FORMAT menu Refer to nputting image from Main to Sub 23 and Inputting image from Main to Sub Video signal either component or video 26 For DHD951 COMPUTER IN 17 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 STACK menu settings CHKISTIE 3 4 Exiting Intellectual Stack menu Before exiting menu operation for Intellectual Stack it is recommended to check all the settings in the STACK menu For dialogs that are called from the STACK menu you can press the lt button to return to the STACK menu Refer to the following to exit menu operation for Intellectual Stack STACK menu SERVICE COMMUNICATION STACK STACK MODE OFF When you press the lt button functioning as RETURN key after performing some changes to the settings a confirmation dialog will appear SERVICE COMMUNICATION STACK CHANGE STACK SETTINGS RETURN e Pressing the gt button functioning as YES key in the dialog saves the setting and closes the dialog The screen becomes black while the setting is being applied Please wait for a while e Pressing the lt b
8. AISTIE Installation 3 Adjust the image size and position of Set B with the ZOOM FOCUS and LENS SHIFT features such that the image can be superimposed well to the image of Set A EAXOperating Guide Adjusting the lens NOTE Fine adjustment of the image size and position thereafter with functions such as KEYSTONE and 3D KEYSTONE does not increase the image size It is therefore important to have the image of Set B completely overlapping the image of Set A When controlling Set B with the remote control Set A may also respond to the remote control To avoid incorrect operations with the remote control it is recommended to operate with the control panel or a wired remote control KEYLOCK or REMOTE ID function is also available e If you are using Simple Stack go to For Simple Stack users 72 4 Display the menu with the MENU button Operating Guide Using the menu function i Use the A gt buttons to go into the following menu ADVANCED MENU gt OPTION gt SERVICE gt COMMUNICATION gt STACK SERVICE COMMUNICATION STACK STACK menu will appear on screen SUB NUTS zE QOperating Guide OPTION menu RETURN 6 Use the A V buttons to highlight STACK MODE and press the button to display the STACK MODE dialog STACK MODE Highlight MAIN with the 4 buttons and OFF press the lt button to return to the previous T menu Q RETURN gt EXIT T After pressing the gt button
9. DWU951 DHD951 DWX951 DXG1051 User s Manual detailed Instant Stack Guide 020 000663 02 CHAISTIE CHRISTIE Projector DSRS TOND EAS OAS 051 User s Manual detailed Instant Stack Guide Thank you for purchasing this product Features This projector can be used with another projector of the same model to project an image on the same screen using the Instant Stack feature The two projectors can be operated simultaneously to make the image brighter Moreover if you connect two projectors with RS 232C cross over cable it turns to a kind of intellectual stacking system These features generically called Instant Stack provide you with the broad use ADout this mamua Various symbols are used in this manual The meanings of these symbols are described below AWARNING This symbol indicates information that if ignored could possibly result in personal injury or even death due to incorrect handling ACAUTION This symbol indicates information that if ignored could possibly result in personal injury or physical damage due to incorrect handling NOTICE This entry notices of fear of causing trouble 1 Please refer to the pages written following this symbol NOTE The information in this manual is subject to change without notice The illustrations in this manual are for illustrative purposes They may differ slightly from your projector e The manufacturer assumes no responsibility for a
10. INPUT ETE SOURCE and press the gt button to display the FINED COMPUTER IN 1 SUB INPUT SOURCE dialog Siete OEY 4 Use the A V buttons to highlight FIXED COMPUTER IN 1 and press the gt button to complete the setting 79 5 Press any button to select an input port on the remote control or the INPUT button of the Main projector The MAIN INPUT SOURCE dialog is displayed on screen Use the A V buttons to highlight the port to which the signal cable is connected and press the button to complete the setting DWU951 MAIN INPUT SOURCE DHD951 MAIN INPUT SOURCE DWxX951 COMPUTER IN 1 CUTER COMPUTER IN 2 DXG1051 NOTE When FIXED COMPUTER IN 1 is selected the MONITOR OUT setting is invalid Operating Guide SETUP menu e When FIXED COMPUTER IN 1 is selected input sources other than COMPUTER IN1 and COMPUTER IN2 cannot be selected e When FIXED COMPUTER IN 1 is selected if any button to select an input port on the remote control or the INPUT button on the Main projector is pressed the dialog for selecting the input source will be displayed For DHD951 COMPUTER IN DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 25 020 000663 02 Rev 1 06 2014 Setting input ports using menu CHKISTIE Inputting image from Main to Sub Video signal either component or video 4 If the STACK menu is already displayed on the screen proceed to 3 below Otherwise press the MENU bu
11. ION gt SERVICE gt COMMUNICATION gt STACK SERVICE COMMUNICATION STACK STACK menu will appear on screen STAGE MODE OFF CQ Operating Guide OPTION menu oy 4 Check the STACK MODE setting in the STACK menu If MAIN is displayed the Main projector is operating Go to 5 3 Setting the menu 25 If SUB is displayed the Main projector is turned off and the Sub projector is operating 24 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE Setting input ports using menu 5 3 Setting the menu If Intellectual Stack with RS 232C connection is used observe the followings When inputting image signals to Sub via Main the operations differ between using computer signals and video signals such as component and video signals inputting image from Main to Sub Computer signal 41 If the STACK menu is already displayed on the screen proceed to 3 below Otherwise press the MENU button on the remote control If the MENU dialog is displayed use the A V buttons to ES highlight MAIN and press the gt button A menu will be _ displayed DEN If the MENU dialog is not displayed the STACK menu will appear 2 Use the A W lt P buttons to go into the following menu ADVANCED MENU gt OPTION Se gt SERVICE gt COMMUNICATION gt STACK STACK menu will appear on screen Operating Guide OPTION menu RETURN 3 Use the A V buttons to highlight SUB
12. MENU or the SETUP menu of ADVANCED MENU COlOperating Guide EASY MENU or SETUP menu The image for Intellectual Stack appears on screen This image includes a TEMPLATE screen with the 3D KEYSTONE dialog from Main Set B and another TEMPLATE screen from Sub Set A Using 3D KEYSTONE on Main Set B adjust the im Image from Sub Set A age size and position of Main Set B to superimpose j well to the image of Sub Set A Operating Guide EASY MENU or SETUP menu It is recommended to adjust in the following ways 1 Roughly adjust the four corners in the order below Image from Main Set B Top left Top right Bottom right Bottom left 2 Fine adjust the four corners in the same way NOTE Refer to NOTES for all users EQ 72 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 11 020 000663 02 Rev 1 06 2014 Installation CHAISTIE For Simple Stack users 1 Press the MENU button on the remote control to display the menu on Set A 2 Use the A W lt gt buttons to open the TEMPLATE dialog then select STACK on the dialog CQ Operating Guide MENU PREFERENCES 3 Press the MENU button on the control panel of Set B to display the menu 4 Use the A W lt gt buttons to select 3D KEYSTONE from EASY MENU or the SETUP 3D KEYSTONE dialog menu of ADVANCED MENU M Operating Guide STACK of TEMPLATE EASY MENU or SETUP menu fa 3D KEYSTONE dialog appears on scree
13. PAL SECAM 4 43 AUTO NTSC PAL SECAM M PAL N PAL COMPUTER IN O lt R O O ETURN EXIT For DHD951 COMPUTER IN 26 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE Setting input ports using menu inputting image to Sub and Main individually 1 If the STACK menu is already displayed on the screen proceed to 3 below Otherwise press the MENU button on the remote control If the MENU dialog is displayed use the A V buttons to highlight MAIN and press the gt button A menu will be displayed If the MENU dialog is not displayed the STACK menu will appear 2 Use the A lt P buttons to go into the following menu ADVANCED MENU gt OPTION SERVICE COMMUNICATION STACK STACK MODE OFF gt SERVICE gt COMMUNICATION gt STACK STACK menu will appear on screen Operating Guide OPTION menu 3 Use the A F buttons to highlight SUB INPUT SOURCE and press the gt button to display the SUB INPUT SOURCE dialog 4 Use the amp buttons to highlight FOLLOW MAIN Ranae UNIT and press the gt button to complete the set FIXED COMPUTER IN 1 ting co 1 8 RETURN 0 EXIT 5 Press any button to select an input port on the remote control or the INPUT button of the Main projector The MAIN INPUT SOURCE dialog will be dis played on screen Use the A V buttons to highlight the port to which the signal cable is connected and press the bu
14. a dialog to confirm whether or not to save the setting IS displayed SERVICE COMMUNICATION STACK Press the button to complete the setting Ce SS CQ 78 ON J YES DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHAISTIE Installation 2 4 Confirming Main and Sub settings 1 Press the MENU button on the remote control for Main Set B Main Set B Sub Set A 3 If you press the gt button the dialog closes and the Main Set B menu will appear when MAIN is highlighted If you press the lt button the dialog closes and the menu will disappear NOTE If these dialogs are not displayed on screen check the RS 232C connection M8 and the MAIN or SUB setting in the STACK MODE dialog 074 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 10 020 000663 02 Rev 1 06 2014 CHAISTIE Installation 2 5 Fine adjusting image position To superimpose the images of Main Set B and Sub Set A fine adjust the image size and position of Main Set B using 3D KEYSTONE For Intellectual Stack users 1 Main Set B Press the MENU button on the remote control or the control panel on Main Set B to display the MENU dialog Highlight MAIN with the A V buttons and press the gt button Menu on Main Set B will appear Using the A lt gt buttons on the remote control or the control panel on Main Set B select 3D KEYSTONE from EASY
15. ck When using Intellectual Stack via RS 232C connection ensure the following settings are set on the two projectors Otherwise the Intellectual Stack menu cannot be operated e STANDBY MODE in SETUP menu NORMAL LQiOperating Guide SETUP menu e COMMUNICATION TYPE under COMMUNICATION in SERVICE menu OFF QoOperating Guide OPTION menu e STACK LOCK in SECURITY menu OFF When STACK LOCK is set to on menus related to Instant Stack cannot be operated It is therefore necessary to set it to off during installation and menu setting 1 Use the A lt P buttons to go into the following menu ADVANCED MENU gt SECURITY gt ENTER PASSWORD gt STACK LOCK STACK LOCK ON STACK LOCK dialog will appear on screen MoOperating Guide SECURITY menu ns RETURN gt EXIT 2 Use the A buttons to highlight OFF and press the button to complete the setting DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 5 020 000663 02 Rev 1 06 2014 Installation CHKISTIE 2 2 Installing the first projector Set A Deciding installation position Decide the position of Set A and its projection angle User s Manual concise Arrangement and Adjusting the projector s elevator NOTE Set the tilt angle of Set A to within 5 degrees from the level line Setting up Set A 1 Turn on Set A 2 Perform the INSTALLATION setting first if necessary as it may change the image position LA Operating Guide
16. cted to any of the projectors e When Intellectual Stack is used the operations or settings of some functions are restricted Refer to this manual for details 28 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 4 020 000663 02 Rev 1 06 2014 CHAISTIE 2 Installation For safety reasons read 1 1 Basic information and preparations W3 4 carefully before installation In addition take note of the followings for proper use of Instant Stack e Use the same model projectors e Arrange the projectors side by side iia e Make sure the projection screen is perpendicular to the projectors e Project images larger than the recommended screen size shown in the table The greater the distance between the projectors the larger the screen size needs to be Projector L distance cm Recommended screen size inch Y y N 00 270 0 10cm lt gt heen or tne e To avoid incorrect operations with the remote control it is recommended to operate with the control panel or a wired remote control if you control one projector with the remote control during installation KEYLOCK or REMOTE ID function is also available Operating Guide OPTION menu e Images from Set A and Set B may superimpose well but the image positions can shift over time Readjust to superimpose the images 2 1 Preparing for Intellectual Sta
17. e LL Operating Guide Using the magnify feature ASPECT and OVER SCAN LX Operating Guide gt SIZE AND POSITION menu COMPUTER IN MoOperating Guide INPUT menu MESSEAGE 8 Operating Guide MENU PREFERENCES DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 19 020 000663 02 Rev 1 06 2014 STACK menu settings CHKISTIE MY BUTTON M Operating Guide OPTION menu TEMPLATE MoOperating Guide MENU PREFERENCES SHUTTER MOperating Guide Temporarily shading the screen SHUTTER TIMER EQ Operating Guide OPTION menu PbyP PIP Operating Guide PbyP PIP EDGE BLENDING MoOperating Guide SETUP menu COLOR WHEEL EX Operating Guide IMAGE SETTINGS menu The following functions are disabled STANDBY MODE EX Operating Guide SETUP menu AUTO SEARCH LX Operating Guide OPTION menu DIRECT POWER ON Operating Guide OPTION menu AUTO POWER OFF MoOperating Guide OPTION menu COMMUNICATION TYPE MoOperating Guide OPTION menu SERVICE COMMUNICATION SOURCE SKIP EQ Operating Guide OPTION menu LAMP MODE M Operating Guide SETUP menu ALTERNATE M Operating Guide SETUP menu LAN port cannot be selected When the projectors are in the PbyP PIP mode the SUB INPUT SOURCE is fixed at FOLLOW MAIN UNIT When Intellectual Stack is in use an error message will be displayed if an error occurs on either projector In
18. e problem with the following measures Press the AUTO button on the remote control or execute AUTO IMAGE on each of the projectors Adjust H POSITION and V POSITION on each of the projectors Check the RESOLUTION setting in the INPUT menu and change to the same setting if the setting differs between Main and Sub Operating Guide Using the automatic adjustment feature SIZE AND POSITION menu AUTO IMAGE H POSITION or V POSITION INPUT menu RESOLUTION If you require more information on Instant Stack please consult your dealer DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 31 020 000663 02 Rev 1 06 2014 Corporate offices USA Cypress ph 714 236 8610 Canada Kitchener ph 519 744 8005 Consultant offices Italy ph 39 0 29902 1161 Worldwide offices Australia ph 61 0 7 3624 4888 Brazil ph 55 11 2548 4753 China Beijing ph 86 106561 0240 China Shanghai ph 86 21 6278 7708 Eastern Europe and Russian Federation ph 36 0 147 48 100 France ph 33 0 141 214404 Germany ph 49 2161 664540 India ph 91 080 6708 9999 Japan ph 81 3 3599 7481 Korea Seoul ph 682 2 702 1601 Republic of South Africa ph 27 0 11 5100094 Singapore ph 65 6877 8737 Spain ph 3491 633 9990 United Arab Emirates ph 971 4 3206688 United Kingdom ph 44118 977 8000 D For the most current technical documentatio
19. ecting input source for Sub 1 Highlight SUB INPUT SOURCE in the STACK S FOLLOW MAIN UNIT menu with the 4 buttons then press the gt ee button to display the SUB INPUT SOURCE dialog 2 Use the A buttons in the dialog to highlight FOLLOW MAIN UNIT or FIXED COMPUTER IN 1 FOLLOW MAIN UNIT Sets the input source on the Sub projector to the same port as Main FIXED COMPUTER IN 1 Sets the input source on the Sub projector to the COMPUTER IN1 port which is connected to the MONITOR OUT port on the Main projector 3 Press the lt button to return to the previous menu or press the gt button to complete the setting M 78 NOTE When the projectors are in the PbyP PIP mode the SUB INPUT SOURCE is fixed at FOLLOW MAIN UNIT e If FIXED COMPUTER IN 1 is selected either the COMPUTER IN1 or IN2 port can be selected as an input source on the Main projector When any button to select an input port on the remote control or the INPUT button on the projector is pressed the MAIN INPUT SOURCE dialog will be displayed on screen Select COMPUTER IN 1 or COMPUTER IN 2 with the A V buttons e If FIXED COMPUTER IN 1 is selected the COMPUTER IN1 port on the Sub projector should be connected to the MONITOR OUT port on the Main projector with a computer cable The image from the selected port is output from the MONITOR OUT port on the Main projector to the COMPUTER IN1 port on the Sub projector The MONITOR OUT setting on
20. ings 13 3 1 Displaying STACK menu 13 3 2 Selecting Main Sub or off 14 3 3 Selecting input source for Sub 17 3 4 Exiting Intellectual Stack MENU cccsseccseseeeeeseeeeeees 18 STACK Menu siscaccenceztocccesntteotesecuetcaves 18 Dialog from STACK menu 55 18 3 5 Important information for Intellectual Stack 0 19 4 Connecting cables 22 4 1 Connecting an RS 232C cable 22 4 2 Connecting signal cables 23 Inputting image from Main to Sub 23 Inputting image to Sub and Main individually 23 5 Setting input ports USING MONU cccsceeeseeeeeeees 24 5 1 Preparing for menu operations 24 5 2 Checking Main projector s operating status cccceeeeeees 24 5 3 Setting the menu 0000 25 Inputting image from Main to Sub Computer Signal 0eseeeee 25 Inputting image from Main to Sub Video signal either component or video 26 Inputting image to Sub and Main individually 26 6 Restrictions on Schedule function 28 7 Troubleshooting 30 020 000663 02 Rev 1 06 2014 CHKISTIE 1 Introduction 1 1 Basic information and preparations Instant Stack Instant Stack is a feature that allows you to superimpose images projected from two projectors easily Intellectual Stack and Simple Stack Instant Stack includes the fo
21. llectual Stack connect an RS 232C cross cable between the CONTROL ports on the Main and Sub projectors M8 This connection is not required if you are using Simple Stack NOTE If the RS 232C cable connecting the two projectors operating in Intellectual Stack is disconnected the projectors will exit from Intellectual Stack and start to operate individually Intellectual Stack will not restart even if the cable is reconnected Follow the procedures below to restart Intellectual Stack 1 Do not operate the projectors for more than 10 seconds after disconnecting the cable to allow the projectors to recognize the disconnection of the cable 2 Turn off both projectors and allow them to cool sufficiently 3 Reconnect the two projectors with the RS 232C cable and turn them on again Intellectual Stack will restart DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 22 020 000663 02 Rev 1 06 2014 CHKISTIE Connecting cables 4 2 Connecting signal cables There are two methods to input image to the Sub projector M77 Inputting image from the MONITOR OUT port on Main to Sub Inputting image to Sub and Main individually Inputting image from Main to Sub 4 Connect the MONITOR OUT port on Main a to the COMPUTER IN1 port on Sub with a computer cable 2 Connect the image output device to one of the input ports on Main
22. llowing two features When two projectors are connected via an RS 232C cable with necessary set tings performed on the projectors these two projectors will automatically operate in synchronization with each other according to the settings This is called as Intellectual Stack in this manual The two projectors operate individually without the RS 232C connection This is called as Simple Stack in this manual Remote control for Intellectual Stack and Simple Stack For Intellectual Stack one projector is set as Main and the other is set as Sub Only the Main projector is capable of receiving the remote control signals Operate the projectors from the control panel of the Main projector or with the remote control pointing at the Main projector For details on operating with remote control and from the control panel refer to 3 5 Important Information for Intellectual Stack For Simple Stack both projectors can receive the remote control signals To avoid incorrect operations with the remote control it is recommended to operate with the control panel or a wired remote control KEYLOCK or REMOTE ID function is also available LQ Operating Guide OPTION menu If you require more information on Instant Stack please consult your dealer DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 Introduction CHAISTIE NOTICE P Intellectual Stack can be operated only in pairs of the same model projector
23. n Set TEST PATTERN settings to ON to display the test pattern 5 Using 3D KEYSTONE on Set B adjust the image size and position of Set B to superimpose well to the image of Set A It is recommended to adjust in the following ways 1 Roughly adjust the four corners in the order below Top left Top right Bottom right Bottom left 2 Fine adjust the four corners in the same way STACK of TEMPLATE NOTES for all users For details on 3D KEYSTONE refer to 3D KEYSTONE of EASY MENU or SETUP menu in the Operating Guide e It is strongly recommended to use a flat screen If a curved or skewed screen is used it is very difficult to align the two images even if you use the pin barrel adjustment of 3D KEYSTONE e Even through fine adjustment of the images from the two projectors it may not be possible to superimpose the images well enough depending on the input signals In this case try the following methods Press the AUTO button on the remote control or execute AUTO IMAGE LQ Operating Guide SIZE AND POSITION menu on each of the projectors Adjust H POSITION and V POSITION EQ Operating Guide SIZE AND POSITION menu on each of the projectors Check the RESOLUTION setting in the INPUT menu and change to the same setting if the setting differs between Main and Sub MoOperating Guide INPUT menu 12 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014
24. n please visit www christiedigital com ed hy i
25. ny errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment All the trademarks in this manual are the properties of their respective owners 1 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 Contents aa 1 Introduction ccceeeeeeeeees 3 1 1 Basic information and preparations cccceeeeeeeees 3 Instant Stack 0 0 cccecceeseeseeseeseeeeeeeeeeees 3 Intellectual Stack and Simple Stack 3 Remote control for Intellectual Stack and Simple Stack ccccecseeeeeee ee 3 2 Installation 0seeeee 5 2 1 Preparing for Intellectual Stack 5 2 2 Installing the first projector Set A 6 Deciding installation position 6 Setting up Set A ceeeeeeeeees 6 2 3 Installing the second projector Set B 8 Deciding installation position 8 Connecting projectors ccccceeeeee 8 Setting up Set B c ce eeeeeeeeeeees 8 2 4 Confirming Main and SUD SEUNG Srccsvidieeccedeneendoinn 10 2 0 Fine adjusting image position sidcicesensrtewwaccuinicneooses 11 For Intellectual Stack users 11 For Simple Stack USEIS c00000 12 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide CHAISTIE ae 3 STACK menu sett
26. on is pressed for three seconds a menu to select MAIN or SUB is displayed If MAIN is selected the Status Monitor on the Main Projector can be operated e There are operating restrictions as E EASY MENU SELECT ASPECT NORMAL follows KEYSTONE ON 3D KEYSTONE OFF _ AUTO POWER OFF and FREEZE MENU 3 PICTURE MODE STANDARD ECO MODE NORMA MAIN tat functions on both projectors are Se mper A EXIT Ox FILTER HOURS Oh disabled Warnlito select LANGUAGE ENGLISH ADVANCED MENU The test patterns for CUSTOM of MAIN or SUB FI EXIT COMPUTER IN 1 GAMMA and COLOR TEMP are 1234567 890ABCDEF ieee boats not displayed Menu on Main projector e The screen may be darker when any ggg KEYSTONE of the OSDs are displayed in PbyP or fiw a gt se PIP display because one of the two Wai oie mac Menu to select Menu on Main projector projectors displays the black screen MAIN or SUB ian DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 15 020 000663 02 Rev 1 06 2014 STACK menu settings CHKISTIE NOTE The images projected from the Main and Sub projectors may be different It is recommended to set the projectors as follows Set the same image for TEMPLATE and START UP on the Main and Sub projectors Capture the same image for My Screen on the Main and Sub projectors Save the same image on MY IMAGE on the Main and Sub projectors Set the same message content for the Messenger function EQ Ne
27. rectly Check the connection of cables Also check that the cable connection matches with the port settings in the menu ae Operating Guide Connecting with your devices The Main and The RS 232C cable between the Main and Sub projector do Sub projectors is not properly connected not operate in Connect the RS 232C cable properly and synchronization restart the Main projector 30 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHRISTIE Phenomenon Cases not involving a machine defect Troubleshooting Reference page The STACK menu does not work The images are either out of focus or not performing fine adjustment The settings on the projectors are not set for the Intellectual Stack feature Check the following settings on the Main and Sub projectors STANDBY MODE in SETUP menu NORMAL COMMUNICATION TYPE under COMMUNICATION in SERVICE menu OFF STACK LOCK in SECURITY menu OFF The remote control is pointed at the Sub projector the Main projector is capable of receiving the remote control signals Therefore point at the Main projector when using the remote control The two images are not superimposed correctly Adjust to superimpose the images with the ZOOM FOCUS and LENS SHIFT features If necessary adjust 3D KEYSTONE and KEYSTONE as well There are some adjustment differences in the two images Try to resolve th
28. ror Color Wheel or Color E Color Wheel Error Wheel switching does not work Humidity Error Humidity is too high l Humidity Error Other Error Errors except the above 2 Other Error e lf you need to turn off a projector for reasons such as taking corrective actions for an error turn off both the projectors so that Intellectual Stack can be started properly when the projectors are turned on again e f the PIN LOCK security function on both projectors is set to ON enter the security code for Main first then followed by the Sub LQOperating Guide gt SECURITY menu 21 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 0 20 000663 02 Rev 1 06 2014 CHAISTIE 4 Connecting cables To superimpose two images onto one screen the same image must be input to the Main and Sub projectors There are various methods to input the image to the projectors This chapter describes the ways of connecting the cables Read this chapter to find a method that meets your needs NOTE If Simple Stack without an RS 232C connection is used the Main and Sub projectors described below do not exist Main in this chapter is read as one projector and Sub as the other projector e For details on the specifications of the input ports refer to Connecting with your devices MoOperating Guide Setting up and Connection to the ports CQ Operating Guide Technical 4 1 Connecting an RS 232C cable If you are using Inte
29. s gt A maximum of two projectors can be used as Intellectual Stack gt Please use the same type of lens for both projectors gt Please set the same Color Wheel settings for both projectors gt Depending on the installation and surrounding environment images projected from the two projectors may not superimpose well enough The images cannot superimpose well enough especially when the screen is slanted deformed or the surface is uneven e Images projected immediately after turning on the projectors are unstable due to rising internal temperature Wait for more than 20 minutes before starting to adjust the superimposed images e The image positions may shift due to temperature change vibration or shock caused by hitting the projector Install the projectors in a stable environment when using Instant Stack If the image positions are shifted readjust the images M6 8 77 e The image positions may shift over time due to the tension and the weight of the connecting cables Make sure not to impose any load on the projectors when arranging the cables e When two projectors are connected using the RS 232C cable the Main projector will be able to control the Sub projector This feature is called as Intellectual Stack 5 When Intellectual Stack by means of RS 232C feature is used RS 232C communication cannot be used to control the projector If you wish to control the projectors from a computer use the LAN connection that is conne
30. s not allow you to turn off only the Sub projector The Main and Sub projectors turn off when the button is pressed for more than 3 seconds And pressing the button does not turn on the Main or Sub projector e The Main projector is capable of receiving the remote control signals but not the Sub projector so the remote control should be pointed at the Main projector e Each Status Monitor can also be operated individually from the respective control panel of the Main and Sub projectors Only the monitor on the projector that has been turned on can be operated with the remote control e f a wired remote control is used connect the cable to the Main projector instead of the Sub projector e AUTO SEARCH function is disabled when the projector is used in Intellectual Stack e Network communication to Sub and Web Control on Sub cannot turn on the Sub projector The Sub projector can only be controlled through the Main projector e The Web Remote Control function of the Sub projector is disabled EQ Network Guide 3 1 11 Remote Control e f you try to turn on the projectors using the Power on amp Display on feature on the Messenger function the projectors will exit Intellectual Stack and display the specified message To start Intellectual Stack again re select MAIN SUB on both projectors in the STACK MODE dialog or turn off and on both projectors again e The Main and Sub projectors have the following common settings Magnifying featur
31. s recommended to operate with the control panel or a wired remote control KEYLOCK or REMOTE ID function is also available DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 Installation CHKISTIE 2 3 Installing the second projector Set B Deciding installation position Decide the position of Set B and its projection angle User s Manual concise Arrangement and Adjusting the projector s elevator NOTE Set the tilt angle of Set B to within 5 degrees from the level line Connecting projectors To use Intellectual Stack connect an RS 232C cross cable between the CONTROL port of Set A and Set B D o gt lt wor 9g Z Setting up Set B 1 Turn on Set B NOTE After turning on Set B make sure the image of Set B is not significantly tilted compared to the image of Set A If the image is overly tilted rotate the elevator feet of Set B to adjust the angle such that the tilt is just about right 2 Reset the adjustment of KEYSTONE and 3D KEYSTONE on Set B COlOperating Guide EASY MENU or SETUP menu NOTE KEYSTONE 3D KEYSTONE BLENDING or WARPING function cannot be used at the same time Please use an appropriate function e Perform the INSTALLATION setting first if necessary as it may change the image position Operating Guide SETUP menu DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 8 020 000663 02 Rev 1 06 2014 CH
32. splay the STACK MODE dialog G RETURN EXIT 2 Use the A F buttons in the dialog to highlight MAIN SUB or OFF OFF Disables Intellectual Stack MAIN Sets the projector to Main that functions as a control tower SUB Sets the projector to Sub that functions as a follower 3 Press the lt button to return to the previous menu or press the gt button to complete the setting M 78 NOTE After setting Main or Sub the setting information can be checked on Projector Web Control EQ Network Guide Projector Web Control Select Projector Status in the main menu of Projector Web Control The Stack Mode item shows whether your projector is set to MAIN or SUB even if STACK MODE is set to OFF 14 DWU95 1 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE STACK menu settings NOTE A menu to select MAIN or SUB appears on screen when a button on the control panel of the projector or remote control is pressed Select the projector that you want to operate Refer to the examples below When the MENU button is pressed a menu to select MAIN or SUB is displayed If MAIN is selected EASY MENU or ADVANCED MENU of the Main projector is displayed When one of the KEYSTONE FOCUS ZOOM ZOOM and LENS SHIFT buttons is pressed a menu to select MAIN or SUB is displayed If MAIN is selected each menu or dialog of the Main projector is displayed When the ENTER butt
33. trol or STANDBY ON button of the Main projector e The projectors cannot be turned on by the Schedule function on the Sub projector Set it on the Main projector if necessary DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 29 020 000663 02 Rev 1 06 2014 CHAISTIE M Troubleshooting About the phenomenon confused with a machine defect check and cope with it according to the following table Phenomena that may be easy to be mistaken for machine defects Reference Phenomenon Cases not involving a machine defect page No power is supplied to the Main and Sub projector an To use the Intellectual Stack feature User s Manual supply AC power to both the Main and Sub concise gt projectors If AC power is supplied to only Connecting one of the projectors Intellectual Stack is power supply disabled The RS 232C cable between the Main and Sub projectors is not properly connected To use the Intellectual Stack feature connect an RS 232C cross cable between the Main and Sub projectors If the cable is not connected the Main projector cannot control the Sub projector The menu settings for Intellectual Stack are not performed correctly Check the settings of the STACK menu on the Main and Sub projectors To use the Intellectual Stack feature one projector must be set to Main and the other projector must be set to Sub Intellectual Stack does not work Signal cables are not connected cor
34. tton on the remote control If the MENU dialog is displayed use the A V buttons to highlight MAIN and press the gt button A menu will be displayed If the MENU dialog is not displayed the STACK menu will appear 2 Press the MENU button on the remote control DWU951 DWX951 DXG1051 or control panel on the Main projector SEIT Use the A W lt P gt buttons to open the uro SYNCONG vipeo COMPUTER IN dialog comrenni 9 o CQ Operating Guide INPUT menu RETURN DHD951 COMPUTER IN SYNC ON G AUTO OFF VIDEO COMPUTER IN 4 RETUR O O 3 To input component signals to COMPUTER IN1 or IN2 set the port to AUTO Then use the A gt buttons to highlight EXIT and press the gt button to complete the setting To input video signals to COMPUTER IN1 or IN2 set the port to VIDEO If it is necessary to select a video format use the A W lt gt buttons to highlight RETURN and press the lt button to display the INPUT menu Otherwise use the A gt buttons to highlight EXIT and press the button to complete the setting 4 Select VIDEO FORMAT in the INPUT menu to display the VIDEO FORMAT dialog Select AUTO or an appropriate format ue for the video signal input COMPUTERNI O O O O Then use the A W lt gt buttons to RETURN highlight EXIT and press the gt button to complete the setting DHD951 VIDEO FORMAT NTSC 4 43 DWU951 DWX951 DXG1051 VIDEO FORMAT a NTSC AUTO NTSC
35. tton to complete the setting RETURN DWU951 MAIN INPUT SOURCE DHD951 MAIN INPUT SOURCE COMPUTER IN DWX951 COMPUTER IN 1 COMPUTER IN 2 DXG1051 NOTE lf FOLLOW MAIN UNIT is selected selecting the input source on either the Main or Sub projector will automatically set the other projector to the Same source e lf FOLLOW MAIN UNIT is selected LAN cannot be selected e When FOLLOW MAIN UNIT is selected if any button to select an input port on the remote control or the INPUT button on the Main projector is pressed the dialog for selecting the input source will be displayed 27 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHAISTIE 6 Restrictions on Schedule function This model supports the Schedule function on the Projector Web Control feature LQ Network Guide 3 1 7 Schedule Settings There are some restrictions on the functions when Intellectual Stack with RS 232C connection is used But for Simple Stack without an RS 232C connection there is no restriction on the functions Regardless of whether Intellectual Stack or Simple Stack is used take note of the Schedule settings before using the Stack function Refer to the following for the restrictions concerning Intellectual Stack If you are using Simple Stack skip this chapter Restrictions on the Main eee Power Functions status ane On Restrictions on the Sub projector
36. twork Guide Messenger Function on the Main and Sub projectors e Image shift can result in image quality degradation on the screen Perform the INSTALLATION setting before adjusting the image position as the image position will change when the INSTALLATION setting is changed EQiOperating Guide SETUP menu e When PIN LOCK on both projectors is set to ON MoOperating Guide SECURITY menu cancel the settings of the two projectors e When Intellectual Stack is in use the POWER indicator on the projector operates differently from normal When both the Main and Sub projectors are in standby mode the Main projector determines which projector to turn on according to the STACK MODE setting if the ON button on the remote control or STANDBY ON button of the Main projector is pressed The POWER indicator on the Main projector blinks in green when the Sub projector is going to turn on If the Main projector is turned on the POWER indicator on the Main projector turns to steady green after lighting up as per normal If the Sub projector is turned on the POWER indicator on the Main projector lights in orange after the Sub projector is turned on If an error occurs on the Main projector the Sub projector turns on and the POWER indicator on the Main projector lights or blinks in red DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 1 6 020 000663 02 Rev 1 06 2014 CHKISTIE STACK menu settings 3 3 Sel
37. utton functioning as NO key in the dialog returns you to the COMMUNICATION menu without saving the setting MOperating Guide OPTION menu SERVICE One J YES Dialog from STACK menu SUB INPUT SOURCE FOLLOW MAIN UNIT When you press the gt button functioning as EXIT PED COMPUTER IN 1 key after performing some changes to the settings a confirmation dialog will appear e Pressing the gt button functioning as YES key in the dialog saves the setting and closes the dialog The screen becomes black while the setting is being applied Please wait for a while e Pressing the lt button functioning as NO key in the dialog closes the dialog without saving the setting SERVICE COMMUNICATION STACK CHANGE STACK SETTINGS ONO J YES 18 DWU951 DHD951 DWX951 DXG1051 User s Manual Instant Stack Guide 020 000663 02 Rev 1 06 2014 CHKISTIE STACK menu settings 3 5 Important information for Intellectual Stack This section provides important information for setting up the Main and Sub projectors not explanations on operating the menus Read all information carefully e To use Intellectual Stack one projector must be set to Main and the other set to Sub e All buttons except the STANDBY ON button on the control panel of the Sub projector are disabled Operate the projectors with the control panel of the Main projector or the remote control e Pressing the STANDBY ON button of the Sub projector doe
Download Pdf Manuals
Related Search