Minn Kota accessories available for your motor.
Contents
1. Safety Latch INSTALLATION OF THE BOWMOUNT We recommend that you have another person help with this procedure 1 For installation do not remove the shaft motor from the Bowguard The Bowguard spring is under tension and must always remain secured 2 Place the mount with the motor in the fully retracted flat position on the deck of the boat The motor should be mounted as close to the centerline of the boat as possible Make sure bow area under the chosen location is clear and unobstructed for drilling CAUTION MAKE SURE YOUR MOTOR IS MOUNTED ON A LEVEL SURFACE Make sure the motor rest is positioned far enough beyond the edge of the boat The motor as it is lowered into the water or raised into the boat must not encounter any obstructions 3 Once in position mark at least four 4 of the holes pro vided in the bow plate and drill through the marks using a 9 32 bit 4 Mount the plate to the bow through the drilled holes using the provided 1 4 20 x 3 1 2 bolts nuts and washers NOTE If possible secure all sets of mounting bolts nuts and washers MAINTENANCE OF THE PRODUCT 1 After use these units should be rinsed with fresh water then wiped down with a cloth dampened with an aque ous based silicone spray such as Armor All 2 The propeller must be cleaned of weeds and fishing line The line can get behind the prop wear away the seals and allow water to enter the motor Check2. rope may cause the mount to spring open rapidly striking anyone or anything in the direct path 2991749 Mount Fortrex Short 52 700 940 1 E 2993916 Sideplate assembly long left sw 1 m 2991750 Mt Fortrex Long 80 62 700 940 1 895 2288625 Support left sideplate 1 TN m 2991751 Mt Fortrex Long 101 62 700 940 1 900 2283408 Screw 8 x 3 8 8 To disconnect one end of the gas spring follow the instructions below 700 2280800 Link bowguard mount left 1 905 2283911 Sideplate short left sw 1 710 2287303 Bushing upper pins 2 2283916 Sideplate long left sw 1 1 With the mount the stowed position locate the upper cylinder 711 2287304 Bushing delrin 2 910 2073408 Screw 1 4 20 x 7 8 2 2 2 Using two Philips screwdrivers remove 1 of the Phillips flat head screws 715 2283409 Screw 1 4 20 x 3 4 FHSC 1 915 2286700 Plug spacer 2 m 3 Remove pin from outer arm by sliding thru the arm 720 2880400 Pull grip assembly 1 920 2283900 Ramp motor 1 a 4 Now it is safe to deploy the motor and remove the motor assembly 721 2261732 Washer 2 BH 2993921 Sideplate assembly short right sw 1 gt 730 2281516 Spacer inner a 925 2288820 Support rightsideplate 4 2 pacer inner arm upport right sideplate T a 735 2281702 Washer lock 1 4 1 930 2283921 Sideplate short right sw 1 737 2284202 Outer arm short 52 1 2283926 Sideplate long right sw 1 2284212 Outer arm long 62 1 932 2285501 Decal Side
3. this after every 20 hours of operation 3 Before each use check to see that the prop nut is secure 4 To prevent accidental damage during trailering or stor age disconnect the battery whenever the motor is off of the water For prolonged storage lightly coat all metal parts with an aqueous based silicone spray 5 For maximum performance restore battery to full charge before each use TROUBLESHOOTING 1 Motor fails to run or lacks power Check battery connections for proper polarity Make sure terminals are clean and corrosion free Use fine sandpaper or emery cloth to clean terminals Check battery water level Add water if needed 2 Motor loses power after a short running time Check battery charge if low restore to full charge 3 Motor is difficult to steer Check steering cables for proper tension Adjust as neces sary 4 You experience prop vibration during normal operation Remove and rotate the prop 180 See removal instructions in prop section 5 Unit difficult to deploy 6 Keep battery terminals clean with fine sandpaper or emery cloth 7 The weedless wedge propeller is designed to provide absolute weed free operation with very high efficiency To maintain this top performance the leading edge of the blades must be kept smooth If they are rough or nicked from use restore to smooth by sanding with fine sandpaper 8 Grease latch pins periodically to prevent binding or stick ing 9 T
4. Minn Kota accessories available for your motor Power Center 2 Quick Plugs Extension Handles Anywhere Anytime Visit our website at www minnkotamotors com 2010 Johnson Outdoors Marine Electronics Inc P N 2287101 33016 3 11 o OTE Master User Manual for RIPTIDE SF NOTE DO NOT RETURN YOUR MINN KOTA MOTOR TO YOUR RETAILER YOUR RETAILER IS NOT AUTHORIZED TO REPAIR OR REPLACE THIS UNIT YOU MAY OBTAIN SERVICE BY CALLING MINN KOTA AT 1 800 227 6433 oR 1 507 345 4623 RETURNING YOUR MOTOR TO THE MINN KOTA FACTORY SERVICE CENTER SENDING OR TAKING YOUR MOTOR TO ANY MINN KOTA AUTHORIZED SERVICE CENTER ON ENCLOSED LIST PLEASE INCLUDE PROOF OF PURCHASE SERIAL NUMBER AND PURCHASE DATE FOR WARRANTY SERVICE WITH ANY OF THE ABOVE OPTIONS SERIAL NUMBER PURCHASE DATE PLEASE THOROUGHLY READ THIS USER MANU AL FOLLOW ALL INSTRUCTIONS AND HEED ALL SAFETY amp CAUTIONARY NOTICES BELOW USE OF THIS MOTOR IS ONLY PERMITTED FOR PERSONS THAT HAVE READ AND UNDERSTOOD THESE USER INSTRUCTIONS MINORS MAY USE THIS MOTOR ONLY UNDER ADULT SUPERVISION peri Pere _ a ix SERT SU wm 4 yy p re Fre BOW MOUNT HAND CONTROL SALTWATER MOTORS Features Assembly Installation Operation Gas Assist Cautions Circuit Breaker Battery Information Battery Connection Wiring Diagram Propeller Replacement Maximizer Mainte
5. PERATION OF THE PRODUCT CONT D Depth Adjustment Firmly grasp the outer shaft or control head and hold it steady Loosen depth setting knob on the hinge cover until the shaft slides freely Raise or lower the motor to the desired depth Turn the motor control head to the desired position Tighten depth setting knob to secure the motor in place NOTE When setting the depth be sure the top of the motor is submerged at least 12 to avoid churning or agitation of surface water The propeller must be com pletely submerged STEERING ADJUSTMENT Adjust steering tension knob to provide enough tension to allow the motor to turn freely yet remain in any posi tion without being held or Tighten the knob and lock the motor in a preset position to leave your hands free for fishing the battery life Failure to recharge lead acid batteries within 12 24 hours is the leading cause of premature battery failure Use a variable rate charger to avoid overcharging If you are using a crank battery to start a gasoline out board we recommend that you use a separate deep cycle marine battery batteries for your Minn Kota trolling motor a C a Depth Collar Knob Advice regarding batteries Never connect the and the terminals of the bat tery together Take care that no metal object can fall onto the battery and short the terminals This would immediately lead to a short and utmost fire danger Recommendation U
6. ase button located on the left underside of the pivot handle Your MAXXUM trolling motor handle also features a unique stow position that is useful for limiting the IMPORTANT THE MOTOR MUST BE IN THE OFF POSITION TO USE THE STOW POSITION FAILURE TO PUT THE MOTOR IN THE OFF POSITION BEFORE STOWING THE HANDLE WILL RESULT IN JOINT FAILURE Handle controls on off steering forward reverse LUT ear and the retangular ring Velcro secures the motor Pull the rope to release the lock bar which automatically engages when the unit is lowered or raised into position The pull grip and rope should be used to both lower and raise the unit f the rope disengages from the lock bar assembly release the lock bar with a screwdriver amount of space required for storage or travel First press the release button located on the left under side of the pivot handle then push the handle down until you feel the handle lock in to the stowed position This will be almost parallel to the motor shaft To extend the handle pull the handle towards you to the desired position The handle will extend a full 6 inches To retract push the handle in until it meets the face of the motor control head Release button CAUTION NEVER OPERATE YOUR MOTOR WHEN IT IS OUT OF THE WATER 12 24 36 VOLT VARIABLE SPEED MODELS THIS IS A UNIVERSAL MULTI VOLTAGE DIAGRAM DOUBLE CHECK YOUR MOTORS VOLTAGE FOR PROPER CONNECTIONS Over Cur
7. ce of collection of your local town council Never dispose of battery in a garbage bin Comply with the disposal directions of the manufacturer or his representative and dispose of them at the proper place of collection of your local town council LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT LIMITED TWO YEAR WARRANTY ON ENTIRE PRODUCT Composite Shaft Johnson Outdoors Marine Electronics Inc warrants to the original purchaser that the composite shaft of the purchas er s Minn Kota trolling motor is free from defects in mate rials and workmanship appearing within the original pur chaser s lifetime Johnson Outdoors Marine Electronics Inc will provide a new shaft free of charge to replace any composite shaft found to be defective more than two 2 years after the date of purchase Providing such a new shaft shall be the sole and exclusive liability of Johnson Outdoors Marine Electronics Inc and the sole and exclu sive remedy of the purchaser for breach of this warranty and purchaser shall be responsible for installing or for the cost of labor to install any new composite shaft provided by Johnson Outdoors Inc Entire Product Johnson Outdoors Marine Electronics Inc warrants to the original purchaser that the purchaser s entire Minn Kota trolling motor is free from defects in materials and work manship appearing within two 2 years after the date of purchase Johnson Outdoors Marine Electronics Inc will at its opti
8. esponsible disposal during the product life cycle WEEE compliance may not be required in your location for electrical amp electronic equipment EEE nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles aircraft and boats In some European Union member states these vehicles are considered outside of the scope of the Directive and EEE for those applications can be considered excluded from the WEEE Directive requirement This symbol WEEE wheelie bin on product indicates the product must not be disposed of with other household refuse It must be disposed of and collected for recycling and recovery of waste EEE Johnson Outdoors Marine Electronics Inc will mark all EEE products in accordance with the WEEE Directive It is our goal to comply in the collec tion treatment recovery and environmentally sound disposal of those products however these requirement do vary within European Union member states For more information about where you should dispose of your waste equipment for recycling and recovery and or your European Union member state requirements please contact your dealer or distributor from which your product was purchased Disposal Minn Kota motors are not subject to the disposal regulations EAG VO electric devices directive that implements the WEEE directive Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper pla
9. he 5 16 Allen scew that attaches the motor to the mount should be periodically tightened to 10 12 ft lbs to prevent motor stowing problems Tighten the Allen screw when the mount is in the deployed position Gas spring relaxes after prolong periods of sitting Stow and deploy motor a few times until latch pins latch freely 6 Motor drains battery when not in use Switch MOM OFF CON switch on foot pedal to OFF position when not in use Motor will drain battery in either MOM or CON positions T Lift assist not functioning Ensure lift assist pin was installed prior to motor use 8 Motor shaft falls to one side of the motor shaft yoke when stowing The 5 16 Allen screw that attaches the motor to the mount should be periodically tightened to 10 12 ft Ibs Tighten the Allen screw when the mount is in the deployed position NOTE For all other malfunctions see enclosed Authorized Service Center ASC listing for nearest ASC A c r m I lt c 3 n N m ad PROPELLER REPLACEMENT Disconnect motor from battery prior to changing the pro peller Hold the propeller and loosen the prop nut with a pliers or a wrench Remove prop nut and washer If the drive pin is sheared broken you will need to hold the shaft steady with a screwdriver blade pressed into the slot on the end of the shaft WEEDEESS PROPELLER ANODE NUT PROP WASHER DRIVE PIN MAXIMIZER The bui
10. ll 1 860 2287300 Bushing rear pivot 2 865 2282602 Pin 3 8 x 3 3 4 1 870 2263011 E ring 3 8 shaft 2 871 2280008 Bearing lglide 2 875 2282720 Spring extension 2 880 2773600 Latch strap assembly short 1 2773601 Latch strap assembly Long 1 885 2261732 Washer 8 nylon 2 890 2373450 Screw 8 18 x 3 8 2
11. lt in Maximizer s electronics create pulse width modulation to provide longer run ning time and extended battery life With the Maximizer speed control you may in some applications experience interference in your depth finder display We recommend that you Turn the old prop to horizontal as illustrated and pull it straight off If drive pin falls out push it back in Align new propeller with drive pin Install prop washer and prop nut Tighten prop nut 1 4 turn past snug 25 35 inch Ibs Be careful over tightening can damage prop CAUTION DISCONNECT THE MOTOR FROM THE BATTERY BEFORE BEGINNING ANY PROP WORK OR MAINTENANCE use a separate deep cycle marine battery for your trolling motor and that you power the depth finder from the starting cranking bat tery If problems still persist call our service department at 1 800 227 6433 INSTALLING THE BOWMOUNT STABILIZER if Included 1 Place motor in the stowed position 2 Unthread the composite rod from the bracket and attach bracket to the bottom of the bowguard using the 5 16 cap screws and nuts The nuts fit into pocket on the inside of the bowguard behind the spring NOTE The bracket can be installed on the left or right side of the bowguard Pull the bumper off the stabilizer rod and place the rod next to the bracket as shown in photo Place the threaded end down onto the deck surface and mark the rod fl above the top of the bracket see photo C
12. nance Troubleshooting Warranty RIPTIDE OVERVIEW Advanced Saltwater Tilt Twist Tiller Extension amp 6 Handle Corrosion Protection i Battery Meter 3 mil acrylic paint we E coated epoxy Chromate conversion coat 7 cleaning process Premium marine alloy aaa meam rm Maximizer Permanently Sealed Electronics Adjustable Depth Collar On select models p n lt Steering Tension Knob SEPRFFPEF APT X f BowGuard 360 Breakaway Protection as Mounting Bracket shown or with Hinge and door Lifetime Warranty Flexible Composite Shaft Permanent Magnet Motor Weedless Wedge Propeller SS Replaceable Sacrificial Anode Extends Protection Against Galvanic Corrosion Specifications subject to change without notice ENVIRONMENTAL COMPLIANCE STATEMENT It is the intention of Johnson Outdoors Marine Electronics Inc to be a responsible corporate citizen operating in compliance with known and applicable environmental regulations and a good neighbor in the communities where we make or sell our products WEEE Directive EU Directive 2002 96 EC Waste of Electrical and Electronic Equipment Directive WEEE impacts most distributors sellers and manufacturers of consumer electronics in the European Union The WEEE Directive requires the producer of consumer electron ics to take responsibility for the management of waste from their products to achieve environmentally r
13. on either repair or replace free of charge any parts including any composite shaft found to be defective during the term of this warranty Such repair or replace ment shall be the sole and exclusive liability of Johnson Outdoors Marine Electronics Inc and the sole and exclu sive remedy of the purchaser for breach of this warranty Terms Applicable to Both Warranties These limited warranties do not apply to motors used com mercially nor do they cover normal wear and tear blemish es that do not affect the operation of the motor or damage caused by accidents abuse alteration modification mis use or improper care or maintenance DAMAGE TO MOTORS CAUSED BY THE USE OF REPLACEMENT PROPELLERS OR OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PROPELLER AND PARTS WILL NOT BE COV ERED BY THIS LIMITED WARRANT Y The cost of normal maintenance or replacement parts which are not defective are the responsibility of the purchaser To obtain warranty service in the U S the motor or part believed to be defective and proof of original purchase including the date of purchase must be presented to a Minn Kota Authorized Service Center or to Minn Kota s factory service center in Mankato MN Any charges incurred for service calls transportation or shipping freight to from the Minn Kota Authorized Service Center or facto ry labor to haul out remove re install or re rig products removed for warranty
14. plate sw 2 _ 740 2992302 Rope guide assembly 1 935 2281902 Base extrusion short 52 1 PANPE 745 2281530 Insert threaded 1 Base extrusion long 62 1 750 2282608 7 16 5 5 32 1 940 2323405 Screw 1 4 20 x 1 2 6 751 2282602 Pin 3 8 x 3 3 4 1 752 2261505 Spacer 2 975 2773806 Strap hold down 1 753 2263011 E ring 3 8 shaft 2 980 2991928 Bracket stabilizer assembly 1 760 2223418 Screw 1 4 20 x 1 2 BHCS 1 765 2993819 Inner arm assembly short 52 1 B 1378132 Propeller kit WW2 Gas Spring Bracket 2993821 Inner arm assembly long 62 1 m 2994876 Propeller bag assy 770 2042711 Spring torsion 1 1000 2331160 Propeller WW2 1 775 2283620 Latch safety 1 1010 2262658 Drive pin large 1 776 2282611 Spring safety latch 1 1015 2091701 Washer prop large 1 780 2281704 Washer 7 16 nylon 1 1020 2198401 Nut nylock prop Anode 1 785 2280805 Link bowguard mount right 1 790 2283410 Screw 1 4 20 x 1 2 PFH 2 2994830 Bag assembly 1 795 2288400 Gas spring cylinder 80 1012 short 1 2288401 Gas spring cylinder 802 long mt 1 2288402 Gas spring cylinder 1012 long mt 1 796 2281710 Spacer gas spring 2 800 2282610 Pin upper shock 1 810 2280005 Bearing nyliner 7 16 4 815 2282600 Pin 7 16 x 4 7 8 1 020 2281932 Bracket rear pivot 2 025 2281501 Yoke shock mount 1 830 2282606 Pin 7 16 x 4 1 2 1 835 2283402 Screw set 6 32 x 1 4 2 845 2282604 Pin Knurled 5 16 x 2 1 850 2283615 Latch bar 1 855 2283610 Bracket latch strap rope pu
15. rent Protection Devices not shown in illustrations CONTROL BOARD CARTE DE COMMANDE BLACK NOIR M UN M M SPEED ADJUSTMENT KNOB MOLETTE DE REGLAGE DE LA VITESSE RED ROUGE M Q Q O BATTERY GAUGE VOLTM TRE pr RED ROUGE B RED ROUGE BLACK NOIR B BLACK NOIR E Q e m 12V BATT 1 MOTOR MOTEUR 12V BATT 3 BATTERY INFORMATION The motor will operate with any deep cycle marine 12 volt battery batteries For best results use a deep cycle marine battery with at least a 115 ampere hour rating As a general on the water estimate your 12 volt motor will draw one ampere per hour and your 24 volt motor will draw 75 ampere per hour for each pound of thrust produced when the motor is running on high The actual ampere draw is subject to your particular environmental conditions and operation requirements Maintain battery at full charge Proper care will ensure having battery power when you need it and will significantly improve These motors are equipped with a push to test battery gauge The LED provides an accurate display of the remaining charge in the battery It is only accurate when the motor is off The gauge reads as Four lights indicate full charge Three lights indicate good charge Two lights indicate low charge One light indicates recharge O
16. se battery boxes and covered battery terminal clamps like Minn Kota accessory MK BC 1 BATTERY CONNECTION a Connect a connector cable to positive terminal of battery 1 and to negative terminal of battery 2 12 Volt Systems b Connect a connector cable to positive terminal of battery 2 1 Make sure that the motor is switched off speed selector on 0 and to negative terminal of battery 3 2 Connect positive red lead to positive battery terminal c Connect positive red lead to positive terminal on bat 3 Connect negative black lead to negative battery terminal tery 3 4 For safety reasons do not switch the motor on until the propeller d Connect negative black lead to negative terminal of bat 00 n j j m A E A O 2 2 A lo 2 is in the water tery 1 4 For safety reasons do not switch the motor on until the propeller Volt Systems is in the water Make sure that the motor is switched off speed selector on 0 2 Two 12 volt batteries are required 3 The batteries must be wired in series only as directed in wiring diagram to provide 24 volts a Connect a connector cable to positive terminal of battery 1 and to negative terminal of battery 2 b Connect positive red lead to positive terminal on battery 2 c Connect negative black lead to negative terminal of bat tery 1 4 For safety rea
17. service or any other similar items are the sole and exclusive responsibility of the purchaser Motors purchased outside of the U S must be returned prepaid with proof of purchase including the date of purchase and serial number to any Authorized Minn Kota Service Center in the country of purchase Warranty service can be arranged by contacting a Minn Kota Authorized Service Center listed on the enclosed sheet or by contacting the factory at 1 800 227 6433 or fax 1 800 527 4464 Note Do not return your Minn Kota motor to your retailer Your retailer is not authorized to repair or replace them THERE ARE NO EXPRESS WARRANTIES OTHER THAI THESE LIMITED WARRANTIES IN NO EVENT SHALL ANY IMPLIED WARRANTIES EXCEPT ON THE COM POSITE SHAFT INCLUDING ANY IMPLIED WAR RANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE EXTEND BEYOND TWO YEARS FROM THE DATE OF PURCHASE IN NO EVENT SHALL JOHNSON OUTDOORS MARINE ELCTRONCIS INC BE LIABLE FOR INCIDENTAL CON SEQUENTIAL OR SPECIAL DAMAGES Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of inci dental or consequential damages so the above limitations and or exclusions may not apply to you This warranty gives you specific legal rights and you may also have othe legal rights which vary from state to state WARNING This product contains chemical s known to the state of California to cause cancer and or reproductive to
18. sons do not switch the motor on until the propeller is in the water 12 Minimum depth If installing a leadwire plug observe proper polarity and fol low instructions in your boat owner s manual See wiring diagram on following pages IMPROPER WIRING OF 24 OR 36 VOLT SYSTEM COULD CAUSE BATTERY EXPLOSION KEEP LEADWIRE WING NUT CONNECTION TIGHT AND 36 Volt Systems 1 Make sure that the motor is switched off speed selector on 0 2 Three 12 volt batteries are required 3 The batteries must be wired in series only as directed in wiring diagram to provide 36 volts SOLID TO BATTERY TERMINALS LOCATE BATTERY IN A VENTILATED COMPARTMENT 129 In Canada parts may be ordered from any of the Fuera de los Estados Unidos consultar la lista anexa para ubicar el Centro de servicio autorizado Please use the correct part numbers from the parts MINN No dejar de incluir el numero del MODELO y el numero de SERIE del motor para el cual rder call 1 800 227 6433 or FAX 1 800 527 4464 se solicitan las piezas Usar siempre los n meros de pieza correctos indicados en la lista de piezas GAS ASSIST LIFT MECHANISM shining and or assembly that is required p n 2284905 REV W 34193 10 12 Item P N Description Qty Item P N Description Qty necting one end of the gas spring Failure to do this can create a condition where accidental pulling of the B 2993911 Sideplate assembly short left sw 1
19. ut the rod to the mark and round the cut edge with a file or sandpaper Install the bottom bumper to the stabilizer rod and thread the rod into the bracket Adjust the stabilizer rod up or down to so that the tip just touches the support surface See photo below WARNING Adjusting the rod too tightly removes the end play needed for proper pin engagement and doing so could prevent the mount from fully latching in the stowed position If installed correctly the rod tip should lift off the deck about 1 4 without the mount unlatching 8 Once adjusted tighten the jam nut against the bracket which will prevent the rod from turning 9 Install top cap if threads are exposed NOOO gt OW 3 4 Optional mounting holes BOW MOUNT OPERATION The bow mount is designed to fold back and lock the motor flat on deck when not in use The motor rest positions the lower unit as it comes in contact with the nose of the mount and guides it onto the motor rest The tube lock tilts up and engages the shaft to lock it for transport The hold down strap assembly crosses over the shaft WARNING WHEN RAISING OR LOWERING MOTOR KEEP FINGERS CLEAR OF ALL HINGE AND PIVOT POINTS AND ALL MOVING PARTS TILT AND EXTENSION HANDLE OPERATION Your MAXXUM trolling motor features 7 usable handle tilt positions 45 30 and 15 up and down from the 0 horizontal position To use the down positions you must first press the rele
20. xicity ASSEMBLY OF MOTOR TO MOUNT 1 2 Place the mount on an elevated surface such as a work bench or tailgate of pickup Remove the 5 16 Allen screw and lock washer from the mount using Allen wrench See picture Align the key ways on the inside of the bowguard with the ends links on the mount Lower the motor assembly straight down until seated Install the 5 16 Allen screw lock washer and tighten to 10 12 ft Ibs Stow the motor into the flat position by pulling the rope handle to disengage the latch bar allowing the motor to fold into the flat position Once in the stowed or flat position the gas spring pin can be installed Follow the steps below to install the gas spring pin Locate the upper gas spring pin in bag assembly Align the end of the gas spring with the holes in the outer arm Install pin and Phillips flat head screws Tighten screws until the heads are flush with the outer arm NOTE Screws have a pre applied thread locker DO NOT apply additional thread locker to screws as that may prevent future removal Motor mount can now be installed onto the boat Proceed to next page for mounting instructions ATTENTION The 5 16 Allen screw must be tight when installed and periodically tightened to 10 12 ft lbs Step 4 which will allow the motor to be stowed prop erly Tighten the Allen screw when the mount is in the deployed position Allen Screw
Download Pdf Manuals
Related Search