installation guide and user manual
Contents
1. 11 11195 N 1 LNB rubber support 13 10543 N 1 LNB mast right hand insert 50 65 13 10531 N 1 LNB mast right hand insert 85 14 10544 N 1 LNB mast left hand insert 50 65 14 10532 N 1 LNB mast left hand insert 85 15 13316 N 2 Flat washer D22x30x0 5 16 10902 NI LNB left hand mast 17 10542 N 1 LNB mast left hand cable cover 18 10903 N 1 LNB right hand mast 19 10541 N 1 LNB mast right hand cable cover 20 10781 N 2 Self tapping screw M2 9x9 5 TPSV 21 03682 N 1 Screw M5x40 22 09015 NI Nut M5 DIN 6923 23 10540 NI LNB tube cover top 85 23 10538 N 1 LNB tube cover top 65 24 10548 N 1 LNB box top 25 11010 NI Rubber support for LNB box top 26 10782 NA Self tapping screw M3 9x25 27 10408 N 2 Self tapping screw M3 9x22 28 15718 N 1 LNB Stark S1 29 10283 N 1 LNB stop U bolt 30 11087 N 2 Screw M4x16 UNI 5739 31 10843 N 1 LNB holder tube 85 31 10842 N 1 LNB holder tube 65 32 10537 N 1 LNB tube cover bottom 65 32 10539 N 1 LNB tube cover bottom 85 33 10547 N 1 LNB box bottom 34 11011 NI Rubber support for LNB box bottom 35 10783 N 1 Self tapping screw M3 9x13 37 03684 N 5 Self locking nut M6 UNI 7474 38 11162 NI Plastic cable locking split pin 39 10693 NI Base fixing 45x40 plate 40 10395 N 1 Base fixing 60x60 plate 41 15617 N 4 FlatwasherD6 21 Tav 2 A KA Tav 2 Pos Code Q t Description 1 11161 N 2 Wiper motor 2 04761 N 2 Waterproof microswitch 3 05086 NA Screw M3x202. 2 5 mm For cable lengths equal to or above 6 metres the minimum cross section is 4 mm Only the Flat Sat Easy Smart must be connected to this cable all the other devices must be connected to another power supply cable The cable connecting the driving unit to the Flat Sat Easy Smart Control Unit must NEVER be cut for any reason whatsoever should the cable turn out to be too long wind the extra part into a coil in a free area of the vehicle Leave a little cable in the driving unit area should any technical operation be required it will make it easier to remove the driving unit Failure to observe these instructions shall render the Warranty null and void LNB rotation for ideal signal reception in extreme South western or South eastern areas in Europe Please be reminded that your outside low noise block converter LNB has its own special mounting position that must be maintained otherwise you will be unable to receive any signals The LNB pre defined installation position is along the dish centre line Fig A in this configuration the Flat Sat Easy Smart system will operate correctly in most European countries If however you happen to find yourselves very far from the orbital position of your required satellite you may want to adjust your low noise block converter angle This is especially true if you wish to receive satellite signals from Astra 19E Astra 28E or HotBird 13E and you are in Portugal or Morocco you will then have to
3. adjust the LNB angle as shown in fig B while if you happen to be in Turkey to receive signals from the same satellites you will have to adjust your LNB to the position shown in fig C Place Position HotBird 13E Astra 19E Astra 28E Lisbona B 25 28 37 Casablanca B 27 34 41 Ankara C 22 15 5 10 LNB tilt adjustment 1 Remove the LNB protective cover by screwing out the 3 screws 2 Loosen the screws on the LNB locking U bolt 3 Turn in the Clockwise West or Anti clockwise South East direction 4 Lock the LNB again by screwing down the screws 5 Close back the LNB protective cover and screw down the 3 screws Important information for proper antenna tracking 1 Before performing antenna tracking operation make sure you have positioned your vehicle so that the view towards the South where Satellite signals come from is free from any nearby obstacle trees houses etc This way the antenna will be free to receive signals coming from the satellite POSITION POSITION 2 It is also important to know that satellites do not transmit with the same intensity throughout Europe so if you are outside the reception area your Flat Sat Easy Smart search might be unsuccessful The reception areas for each Satellite can be found on the main magazines dealing in this line of business Also remember that the larger the dish the more reception area is a
4. galvanized 4 06817 NA Flat washer D 3 UNI6592 galvanized 5 11088 N 2 Screw M4x8 galvanized 6 12945 Ni Connector strip 7 05807 mt 3 6 Coax cable RG 58 8 12294 N i 10 core 2 5mt Motor cable w connector 10 12699 Ni FF13 double female jack 11 15077 N 2 F50 F connector 23 ASTRA19 e HOT BiRDe A Pos Code Q t Description Pos Code Q t Description 1 14897 NI Control unit lid 6 09705 NI 5AFuse 2 14896 NI Control unit bottom 7 01458 N 4 Support 3 09835 NA Black rubber foot 8 11742 N 1 PATCH UTP Cable 4 15860 NI Control panel 9 09318 NI Power supply cable 5 15534 NI 10215 board 24 Code t Description CO CO I O CI BC N 05950 03598 03597 09300 10969 13190 07883 08998 07294 09765 09302 09301 11109 Mama ma 3 m coax cable F F connector Shrink wrap sheath Shrink wrap sheath 10 core 3mt engine unit cont cable w connector Cable cover abs PG completo di gommino 2 cavi 9 m coax cable F F connector 2 m coax cable F F connector 5 m coax cable F F connector 10 core 2mt engine unit cont cable vv connector 10 core 9mt engine unit cont cable vv connector 10 core 5mt engine unit cont cable w connector professional aluminium fairlead complete with PG 21 with gasket for 2 cables CE CONFORMITY CERTIFICATE The manifacturer Teleco Spa Via Majorana nr 49 48022 Lugo RA Declares under its own responsibility that the following products Flat Sa
5. motor driven unit 50 65 85 cm dish Universal LNB SKEW OPTIONAL Control unit Wall mounted control panel Motor connecting cable extension Coaxial cable extension for antenna signal Power Supply Cable Control unit Wall panel connection cable 10 Waterproof box to pass leads through to interior 11 Heat shrinking sheaths 12 Roof attachment plate 13 No 4 Locknuts M6 14 No 4 Screws and Locknuts 15 User s manual CO CO NI O O1 B OO 10 Optional A Important notice Flat Sat Easy Smart is packaged in two separate cartons for transport reasons a the first package contains the driving unit with all the cables and the Control Unit b the second package only contains the dish e It is important to check that the dish has not been damaged during transport when the package is opened In particular check the following well e By resting the dish edge against a flat surface e g the floor or a wall check that it makes contact to the surface all around If it is not so try and make the edge level without denting the dish or call our After Sales Service YES NO z D mg EE lianes EA Br e After checking that everything is in order install the dish on the driving unit as follows 1 Temporarily connect the Control Unit to the driving unit through the grey motor cable 2 Connect the Control panel to the Control Unit through the RJ45 cable 3 Power the Control Unit using a battery Warning
6. 087 28 10535 30 03684 31 11162 32 10693 33 10395 34 15616 19 Dish support mast 50 Parabolic antenna D 500 mm Flat Sat Easy Smart 50 Dish sticker Self locking nut M5 UNI7474 Screw M5x10 UNI 7687 INOX Engine cover Self locking rivet SR 5105 W Hole grommet Motor cover door Self tapping screw M2 9x9 5 UNI 6954 LNB rubber support LNB mast right hand insert 50 65 LNB mast left hand insert 50 65 Flat washer D22x30x0 5 LNB left hand mast LNB mast left hand cable cover LNB right hand mast LNB mast right hand cable cover Self tapping screw M2 9x9 5 TPSV Screw M5x40 Nut M5 DIN 6923 LNB tube cover top 50 Self tapping screw M3 9x25 LNB Stark S1 LNB stop U bolt Screw M4x16 UNI 5739 LNB tube cover bottom 50 Self locking nut M6 UNI 7474 Plastic cable locking split pin Base fixing 45x40 plate Base fixing 60x60 plate Flat washer D 5 85 LO o E Ku gt o uw ND K LL optional 40 Flat Sat Easy Smart 65 85 Pos Code Q ta Description 1 11440 N 1 Dish support mast 65 85 2 03676 N 1 Parabolic antenna D 650 mm 2 07364 N 1 Parabolic antenna D 850 mm 3 15531 N 1 Flat Sat Easy Smart 65 85 Dish sticker 4 03684 NA Self locking nut M6 UNI 7474 5 10910 N 4 Stainless stell screw M6X12 6 10533 N 1 Engine cover 7 10442 N 2 Self locking rivet SR 5105 W 8 11008 N 1 Hole grommet 9 10534 N 1 Motor cover door 10 10384 NI Self tapping screw M2 9x9 5 UNI 6954
7. 22450 Fax 31 0 341 722451 e mail info karmantrading eu www karmantrading eu FRANCE TELECO SAS 3 impasse des lles ZA La Maladi re 07300 St Jean de Muzols France T l 04 75 08 49 17 Fax 09 70 32 83 00 contact telecogroup fr www telecogroup fr SERVICE COMMERCIAL Jean Philippe Bleys T l 02 48 58 0367 Fax 02 48 58 35 85 teleco telair bleysetd com Service Technique T l 06 83 31 44 05 ou 04 75 08 28 25 Foto e disegni non contrattuali Les photos et les dessins ne sont donn s qu titre indicatif We reserve the right to make technical changes without prior notice Fotos und Zeichnungen nicht vertraglich Fotos en tekeningen niet contractueel Fotos y planos no indicados en contrato www telecogroup com ESPANA ADD SICMAP S L EVA Caravan Via Sergia 92 Pol Ind Pla d en Boet II 08302 MATAR Barcelona Tel 93 790 35 26 Fax 93 796 21 17 info addsicmap com Servicio t cnico Fills de Rocha i Lopez S L C Goya 4 08903 L Hospitalet de Llogrebat Barcelona Espa a Tel 933 333 753 Fax 933 337 236 fillsrocha fillsrocha com OSTERREICH TELECO GmbH 82041 Deisenhofen Deutschland Tel 0049 8031 98939 Fax 0049 8031 98949 telecogmbh telecogroup com www telecogroup com SERVICE 0900 94 94 70 DEUTSCHLAND TELECO GmbH 82041 Deisenhofen Deutschland Tel 08031 98939 Fax 08031 98949 telecogmbh telecogroup com www telecogroup com VERTRETUNG Zimmer Technik fiir Mobil
8. For correct connection of the wiring and to prevent damage to the equipment please consult page 9 Connections 4 Press the switch on button on the control panel and wait for the dish support mast to rise 5 Once you have reached the desired position disconnect the power supply cable to switch off the Flat Sat Easy Smart 6 Secure the dish to the mast and screw down the four supplied screws 7 Turn the unit on again and wait for the antenna to close 8 Disconnect the the Control Unit the battery and install the driving unit on the vehicle A Warning NEVER loosen the two dish arm lock screws A to attach the dish as this will result in loss of alignment with the antenna Assembly instructions 1 On the roof of the vehicle choose a free area large enough to allow the antenna to revolve Fig 2 d Driving direction of the vehicle Flat Sat Easy Smart 50 Flat Sat Easy Smart 65 140 cm Flat Sat Easy Smart 85 160 cm 2 2 Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in 3 Remembering that the OUTSIDE UNIT must be fastened as shown on Fig 3 position the base plate as shown on Fig 4 with the short side towards the driving direction of the vehicle 4 Driving direction of the vehicle Driving direction of the vehicle When they ar
9. TELECO FLATSAT EASY S DD A R T 50 FLATSAT EASY S A R T 65 FLATSAT EASY S A R T 85 DBE TELECO wee ECO TELECO installation guide and user manual TELECO WARRANTY Teleco guarantees its satellite dishes and terrestrial antennas against any material and or construction fault and defect The warranty offered by TELECO is limited to the free of charge replacement or repairing of any parts that are deemed faulty by TELECO The warranty is applicable for a period of 3 YEARS starting from the product purchase date however it will only be considered valid if the Customer is able to produce a written document invoice or tax receipt showing the purchase date The following is excluded from the TELECO warranty Damages caused by incorrect installation and or use and or maintenance Damages resulting from product alterations not authorised by Teleco Damages resulting from the use of spare parts different from original Teleco parts Damages resulting from repairs carried out by personnel not authorised by Teleco Normal part wear Expenses incurred for spare parts transport between the Customer s and the service centre g Damages that may occur during transport the Customer shall always be responsible for transport risks a oggw O Information Congratulations on your purchase Flat Sat Easy Smart is among the most technologically advanced products in the field of satellite TV reception This hand
10. book has been prepared to provide information on how to install use maintain and technical specifications your Flat Sat Easy Smart For additional information please contact your local dealer or directly the manufacturers TELECO s p a Via E Majorana 49 48022 LUGO RA Web site www telecogroup com Technical attendance 899 899 856 TELECO p a declines all responsibility for any errors contained in this manual All the contained information are up to the dates of printing and of the above mentioned software revisions TELECO p a reserves the right to introduce any modification made necessary by the development of its products TABLE OF CONTENTS Page Intormationiei A T E EA e AAT List of accessories Installation of dish on motor unit Assembly instructions Control Unit Installation Connections LNB rotation The Smart function Troubleshooting Technical specifications Spare Parts Tables ego sien armament en tava ic teeth ce a Ad equipment as much as possible do not throvv out this end of life appliance together Recycling with a view to reducing disposal of waste electrical and electronic with other unsorted municipal waste but make use of a recycling centre List of accessories Flat Sat Easy Smart is delivered inside a cardboard case that has been specially made to protect it from knocks and pressure The following accessories are supplied External
11. comodate the cables into a protection raceway up to the point where the cables go into the vehicle using the suitable supplied fairlead Seal the fairlead carefully so as to prevent any infiltration by water e a a a a Control Unit Installation 1 Position the Control Unit in an easy accessible ventilated compartment A WARNING Do not install the Control Unit in areas where liquids can be spilled since this could cause irreparable damage Do not install the Control Unit in very small unventilated compartments since overheating could compromise its functionality and render the warranty null and void 2 Place the Control panel comando in an easily accessible visible position 3 Install the connection cables Grey and Black until you reach the OUTSIDE UNIT installation area Control Unit wos Control Panel 55 Note Install the wall mounted control unit with the Grey and Black connection cables bent as shown in the picture This installation tip will prevent any condensation water from flowing down the cables into your control unit electronics damaging it beyond repair and voiding your warranty Connections 1 Connect the grey cable motors to the MOTOR UNIT connector and the Black coaxial cable antenna to the LNB connector of the Control Unit 2 Con
12. e Freizeit Raiffeisenstr 6 64347 Griesheim Tel 06155 797873 Fax 06155 797871 info zimmer mobiltechnik de SERVICE 08921129997 BOSCH ZZ Ss E www facebook com pages Telecogroup 213241202111442
13. e present remove the transparent films from the BASE PLATE Fig 5 4 Clean the lower part of the BASE PLATE carefully applying a layer of glue on the whole surface e g SIKAFLEX 5A 5 Fasten the BASE PLATE to the roof short side towards the vehicle driving direction 6 Apply a layer of silicone all around the BASE PLATE in order to make it completely waterproof Fig 5A Outside Unit Installation 1 Fasten the OUTSIDE UNIT on the base plate and lead the two cables through any of the 4 existing grooves according to the position as shown on Fig 6 WARNING When performing this operation do not draw the two cables forcefully as this might pull them out 2 Fasten the external powered unit to the four stud bolts of the plate using the four nuts supplied with the equipment A Caution to ensure ideal nut tightening and prevent possible pin breaks tighten the nut with a torque wrench set to 8 Newtons metre Connection with extension WARNING The Grey and Black cables coming out of the Outside Unit are generally long enough to allow for connection to the Control Unit If it is not so use the extension cables and perform the following operations 1 Connect the two cables coming from the centre of the OUTSIDE UNIT to the two supplied extensions waterproofing the connectors using the two pieces of heat shrinking tube e IS d 2 Ac
14. er messages nor images appear on the screen a Have you switched your receiver on b Have you switched your TV set on c Have you selected the right satellite Make sure that the services you wish to receive are really available on the required satellite e If the Control panel does not turn on when you press the ON OFF button check the following a Is the battery charged b Is the fuse on the power lead intact Replace it with a 5A one of the same type Technical specifications SPECIFICATIONS Search system Fully automatic NID recognition according to the DVB SI EN 300 468 specifications with DVBS2 tuner Satellites which can be set 10 Extensions USB 1 0 Port Control panel MISCELLANEA Power supply 12 Vdc 10 15 Vdc Absorbed current 5 Amax Current in stand by lt 5mA Fuse 5A Dimensions 160 x 187 x 58 mm Control Unit 119 x 22 x 6 mm Control panel Weight 1 kg Control Unit and Control panel outside driving unit Flat Sat Easy Smart 50 8 8 kg Flat Sat Easy Smart 65 10 5 kg Flat Sat Easy Smart 85 11 6 kg 17 o LO y E Ku gt o uw Ku ae LL optional 33 Flat Sat Easy Smart 50 Q ta Description Pos Code 1 11491 2 06681 3 15531 4 03685 5 10425 6 10533 7 10442 8 11008 9 10534 10 10384 11 11009 13 10543 14 10544 15 13316 16 10902 17 10542 18 10903 19 10541 20 10781 21 03682 22 09015 23 10536 24 10782 25 15718 26 10283 27 11
15. igitaal TV Vlaanderen HD Austria Skylink T l SAT Belgium and Luxemburg In this case the user will have to use 2 remote controls one for the TV and one for the Receiver the same functions already seen with operation of the TELECO mod TY2 TV will be available Error messages In the event of faults or malfunctions the Control Panel indicates the corresponding error on the Display NO SAT No satellite found Check whether the Flat Sat Easy Smart system NO SAT has any obstructions to the SOUTH of the Satellite EL Error The elevation motor is jammed Make sure that no foreign objects Error EL are obstructing normal movement AZ Error The rotation motor is jammed Make sure that no foreign objects are Error AZ obstructing normal movement Error 9 During the switch on stage a motor unit error occurred Error 9 Make sure that no foreign objects are obstructing normal movement 16 Troubleshooting e If the Flat Sat Easy Smart has not found the satellite after a complete search check the following a ls the view towards the South free from any obstacle b Is the place you are at within the reception area of the satellite you have chosen c Is the cable connecting the LNB to the antenna firmly fastened It could have been ripped off or come loose because of contact with an unexpected obstacle d Are all the connections on the Control Unit properly set up If the antenna has stopped after performing tracking but neith
16. me the vehicle engine is started as long as the green safety wire is connected Switching off the Flat Sat Easy Smart If the Control Panel is in standby press the ON OFF key 1 to activate it The backlighting comes on and the Display shows the satellite located message Press the ON OFF key again 1 to park the Flat Sat Easy Smart system The antenna starts to be lowered and the Display shows an animation of the antenna closing When the antenna has been completely closed the Display shows the camper icon with the antenna closed A few seconds later the Control Panel will revert to standby and all the LEDs will go out 15 Automatic antenna parking with safety wire If the vehicle engine is started with the antenna raised the safety wire will immediately lower the dish The Control Panel Display shows an animation of the camper on the move with the antenna closing When the antenna has been completely closed the icon with the camper on the move and the antenna closed remains on the Display A few seconds later the Control Panel will revert to standby and all the LEDs will go out As long as the vehicle is on the move engine on the safety wire keeps the antenna locked in the parking position Flat Sat Easy Smart operation with Teleco and other receivers The Flat Sat Easy Smart is also compatible with the TELECO Satellite Receiver model FORCE HD CLD and with the official receivers of the M7 Group broadcasters CanalD
17. ncorporated satellite receiver and the Control Panel illustrated below LED indicator of selected satellite 4 SAT key 2 Selecting the satellite ASTRA28 HISPASAT INTERNET TURK SAT ON OFF key 1 ON switches on the antenna and starts the search for the selected satellite Display 3 OFF Lowers and switches off the antenna Conirol Panel standby The Control Panel is intelligent to limit electricity consumption it switches off all the LEDs and the Display a few seconds after the system remains idle When the Control Panel is in standby mode the key backlights the LEDs and the Display are off To exit standby mode just press the ON OFF key 1 or the SAT key 2 the backlighting comes on and the Display indicates the antenna status 13 Switching on the Flat Sat Easy Smart First switch on the TY2 TV and then the Flat Sat Easy Smart system If the Control Panel is in standby press the ON OFF key 1 to activate it The backlighting comes on and the Display shows the camper icon with the antenna closed Press the ON OFF key again 1 to switch on the Flat Sat Easy Smart system ASTRAL ASTRA23 The Display 3 alternates the name Be of the selected satellite and an SC ASTRA28 animation of the antenna in search ASTRA28 HISPASAT HISPASAT mode INTERNET TURK SAT INTERNET TURK SAT The Moving dish message appears on the TV screen to i
18. ndicate the antenna is searching for the satellite Astra1 19E Pi When the search has been completed the Display 3 shows the SAT OK message the antenna is pointed at the selected satellite and the TV shows the set programme During the search after a certain time the Moving dish message disappears and the No signal message may appear this remains on the screen until the satellite is located 14 Selecting satellite TV programmes The Flat Sat Easy Smart associates each programme saved on the TV with the satellite that transmits it and therefore every time the user changes channel with the remote control the system immediately checks which satellite is transmitting the programme and automatically positions the antenna accordingly this takes only a short time To check which satellite the antenna is pointed at just look at the panel and read the name of the satellite next to the LED that is on Warning the TV has priority over the Control Panel consequently if the TV is on the choice of channel cannot be forced To force the choice of satellite you must switch off the TV and press the SAT key 2 Note every time a search is made the antenna automatically saves the coordinates of each successfully tracked satellite this is to reduce waiting times in the event of a switch from one satellite to another or if the system is switched back on after the antenna has been parked This saved data is deleted every ti
19. nect the Receiver or the TV with Receiver to the SAT RECEIVER connector You can connect any satellite receiver 3 Connect directly the BLACK cable of the Control Unit to the NEGATIVE POLE of the vehicle 12 Volt Battery and the RED cable to the POSITIVE POLE remember not to mix the and poles up using 2 cables of Black a cross section of 2 5 mm Sat Receiver or Television with Sat Receiver not supplied A WARNING The 3 way power connector P must only be inserted in the 12 Vdc POWER socket Ae Grey Inserting this connector in any other socket will cause irreparable damage to the board and render the warranty null and void Green A 4 The GREEN safety cable of the Control Unit must be connected to the consensus of the vehicle startup console in many cases such consensus is located on Pin 15 in the main terminal board In this way whenever the motor is started this cable receives a positive 12 Vdc voltage which will 1 2V automatically lower the antenna and lock all functions of the Control Unit simultaneously 9 A WARNING This technical note is to call the attention of the installation personnel to certain details of Flat Sat Easy Smart installation During installation you must take the following precautions The power supply cable must directly come from the battery and must have no junctions Minimum cross section of the cable is
20. sible for Antenna closing operations whether by user s control or automatically for vehicle start up require variable time Before starting the vehicle always make sure that the antenna is fully closed The manufacturer declines any liability for all degradations suffered by the product owing to misuse 12 Flat Sat Easy Smart operation The Flat Sat Easy Smart is a fully automatic satellite tracking system able to locate satellites that emit either a DVB S or DVB S2 signal The Flat Sat Easy Smart features a Smart function patent pending The Smart function With the Smart function all the user has to do is select via the remote control the television programme he she wishes to watch and the Flat Sat Easy Smart will automatically point the antenna at the satellite transmitting it To use the Smart function the Flat Sat Easy Smart must be used in conjunction with one of the Teleco TY2 19D TY2 22D TY2 24 or TY2 32 televisions with incorporated satellite receiver this allows the entire system to be piloted simply using just the TV remote control The Flat Sat Easy Smart is also compatible with the Teleco Satellite Receiver model FORCE HD CD and with the official receivers of the following ima da CanalDigitaal TV Vlaanderen HD Austria Skylink T l SAT Belgium and uxemburg Flat Sat Easy Smart operation with TY2 TV To control the Flat Sat Easy Smart you can use the remote control of your mod TY2 TV with i
21. t Easy Smart 50 Flat Sat Easy Smart 65 Flat Sat Easy Smart 85 which are the subject of this certificate conform to the following norms EN 60065 2002 EN 55013 2001 A1 2003 EN 61000 3 2 2000 A2 2005 EN 61000 3 3 1995 A1 2001 A2 2005 EN 55020 2002 A2 2005 according to the terms of the European directive 2006 95 EC Low Voltage modified by 93 68 CEE and 2004 108 CEE of Electromagnetic Compatibility modified by 92 31 CEE e 93 68 CEE of the European Parliament Lugo 31 07 2014 THE PRESIDENT Ing Raul Fabbri 26 STELECO STELECO TELECO 29 10 14 Telair ITALY Via E Majorana 49 48022 LUGO RA Tel 39 0545 25037 Fax 39 0545 32064 mail info telecogroup com DEUTSCHLAND 82041 Deisenhofen Tel 08031 98939 Fax 08031 98949 telecogmbh telecogroup com www telecogroup com FRANCE 3 Impasse des lles ITALY Via E Majorana 49 ZA La Maladi re 48022 LUGO RA 07300 St Jean de Muzols Tel 39 0545 25037 mail contact telecogroup fr Fax 39 0545 32064 www telecogroup fr mail telair telecogroup com www telecogroup com Assistenza 899 899 856 IN EUROPE GREAT BRITAIN SCAN TERIEUR LTD 30 The Metro Centre Tolpits Lane Watford Herts England WD18 9XG Tel 01923 800353 Fax 01923 220358 e mail info scan terieur com www scan terieur com THE NETHERLANDS BELGIUM LUXEMBOURG DENMARK SWEDEN KARMAN TRADING Tel 31 0 341 7
22. vailable WRONG POSITION G RIGHT POSITION ig 11 Tips on the best use of Flat Sat Easy Smart When you park your vehicle make sure that 1 No obstacle for example trees is too near your antenna preventing it from moving freely No metal or glass wall is very near about 5 m the antenna since this would act as a mirror for satellite signals and could induce the antenna to stop towards it 2 Remove any snow or ice from the Flat Sat Easy Smart before actuating it in order to avoid wasting battery power trying to lift it If you decide to turn the engine of your vehicle on in order to re charge its batteries with the safety cable connected to the ignition key the antenna if lifted will come down automatically and it will not be possible to lift it again as long as the engine is running Make sure that your batteries are always sufficiently charged since if the voltage falls below 10 Volts the Flat Sat Easy Smart electronic safety circuit will prevent the antenna from rising Should you use 12 Volt power supply instead of batteries be careful to use stabilized power supply being able to provide 5 A continuously and at least 10 A for short periods At all costs avoid using low quality non stabilized battery chargers It is recommended not to use the antenna under strong wind conditions 80 km h Failure to comply with this condition may result in product degradation which the manufacturer cannot be held respon
Download Pdf Manuals
Related Search