Home

YH6000 user`s manual

1. When it prompts you Data Written into Success put the chip back to run the audio with this new code Address code type 1 operation the types it supports are listed in Diagrams and Charts Collection 2 Example Now a HONDA 1XA0 needs to be decoded 1 Look up Diagrams and Charts Collection find the type under HONDA in Audio Decoding Address type to confirm this instrument can do the type 2 Open the audio 3 Find 93C46 from the board and remove it 4 Then mount the audio and it can be normally used again without any code Cluster Adjusting 1 Operation 1 Types available please refer to Diagrams and Charts Collection If you have a car or cluster not listed to do please contact the manufacturer Do not try it yourself or use other type instead to adjust Or the cluster may be damaged 2 For some special clusters say with 2 chips please refer to the pictures shown in Diagrams and Charts Collection 3 Some clusters whose hands cannot be pull out Do read the appendix Attention for Cluster Adjusting first A 4 Save the data before any adjusting to avoid any data lost caused by chip damaged or mis selecting the type If data incorrect it may cause car no start cluster no displays and cluster running incorrectly and cluster hand moving in disorder A 5 The instrument will auto read the original kilometer when adjusting If similar to the actual Km difference should less than 10
2. Example 1 Now a Buick cluster needs to be replaced we need to change 0 km to be 25000km 1 Look up Cluster Adjusting Models Available under Diagrams and Charts Collection and find Buick 68343 and Buick ST14771 under GM Select the right type according to the chip on circuit board 2 Open the cluster and find the chip on board mainly 8 pin IC with type on it if 68343 or ST14771 is found commonly it can be adjusted 3 Remember its direction and remove it from board then mount it onto the adapter pay attention its direction when welding or inserting 4 Insert the adapter into instrument 5 Start the instrument Press A V and select Adjust Cluster then press ADJUST CLUSTER 6 Select GM and press OK GM 7 Select Buick 68343 Gif ST14771 select Buick STI4771 and press BUICK 68343 8 It prompts you Well Connect the Device and displays the chip type Press 9 The instrument starts to read data and calculate the kilometer Now note that 1f the kilometer calculated 1s similar to the actual one difference should less than 100Km If OK do next operation If not the formula may change please contact the manufacturer Do not continue to adjust ADJUST KM 10 Save data first to avoid any mistake Press A to select Save File and press OK SAVE FILE www autoecu com cn REN BT G 8 R 1
3. Password 6000 Black it for safety Important different countries use different voltages please note that the power adapter it used the input volt should be 100 220V frequency 50 60HZ output 12V 1 5A and shouldbe 2 Work with computer Use a USB cable to connect the computer and the instrument Plug in and then press OK to connect to the host Operation Decode Automobile audio will be locked up when power off improperly It Audio only can work again after inputting the code Adjust To modify Kilometers Change the Kilometer after odometer Cluster repairing or replacing when the device data 1s lost or replacing with a new one Device Use as a programmer Let you read write save display edit and Operation copy the device data View and delete the saved data Operation To resume the original data The device stores other data except Resume U M Data kilometer and audio code so you should write the original data into Audio Decoding Audio mainly has two kinds with IC to decode by modifying the device memory with address code to decode by connecting diode or removing elements Audio with IC 1 Operation 1 1 Please refer to Diagrams and Charts Collection for the audios supported 1 2 Audio type with behind the code cannot be changed Write the right file to get a fix code and the original one cannot be used Example to write file BMW PH7850 1118 into the device the c
4. a box backside and the chip is in it For BMW3 5 only 2 take the box from the cluster then insert it into this socket no need to open the cluster 1 For 8 pin IC such as 93 24 25series 2 A and B and two welding area are the same can use either of them 3 Chip mounting Chip Area Insert it into socket for DIP chips weld it onto welding area for SMD chips Pay attention to the direction when welding or inserting see Identify Chip Pin s Sequence and check any short between pins after welding FZ Gr EARS www autoecu com cn 3 2 Remove free Adapter a Only available for those we offer wiring diagrams b For the odometer with protected lacquer on the circuit board or IC heat the lacquer and clear it and then to weld c Use the 8 colour cables to connect 8 pin 93 25 series socket from the adapter to the 8 points marked on the wiring diagram the first cable is for Pinl and the second for Pin2 the 8th for Pin8 d Check for correct welding before inserting the adapter into the instrument to adjust Name Function LOC KEEN For future use For BMW 3 5 prp Socket For 93series ICs For 25series ICs 93CS56 14pins For SMD LED light CPU Socket Si LED light Universal Adapter Remove free Adapter 4 Chips Mounting Zx 2H nm SMD Devices DIP Devices Operation I Installation 1 Work independently Plug in to start the instrument it ll ask for a password in 5 seconds
5. back to the manufacturer and tell the current kilometer Mile then the technician can solve the problem for you For some clusters you should send them back manufacturer for solution 2 Example Now we have a new car its kilometer needs to be adjusted and we cannot find it in the instrument Please send the data through E mail or by Fax back to the manufacturer 1 Open the cluster and find the chip commonly 8 pin IC with characters on it Supposed the chip it used 1s 93C46 remove the chip from circuit board and put it onto into the adapter 3 Insert the adapter into the instrument 4 Start the instrument press Y to select Device Operation and press OK DEVICE OPERATION 5 Select 93 series press OK 93 SERIES 14 6 Select 93C46 and press OK 93C46 7 prompt you Well connect the device Press OK 8 Select Save File press OK SAVE FILE 9 Name a filename say 002 10 Turn off the instrument connect it with computer 11 Plug in when the screen displays press OK to connect to host 12 E mail File 002 or print and fax it to the manufacturer and please write current Km Mile and Km Mile you want 13 Modify the data as the fax or e mail sent back by the manufacturer I Work With Computer It can be used with computer to update through Internet or send data to manufacturer Details please see the softwa
6. heater inside or iron of 25W heater outside The inside one should be less than 25W the outside should be less than 30W 2 Welding aid selection Use rosin as welding aid substance never use strong corrosive soldering tin paste if rosin has been carbonized amp becomes black replace it 3 Soldering wire selection Select rosin activated core wire with low melting point Removing 1 When removing DIP device use a suction gun or suction pipe to clean welded tin Do not pull it by force 2 When removing SMD device smelt more rosin to the pins and use soldering iron to heat the pins until the device gets entire loose and then remove it Do not pull it by force 3 Heating time should not be too long to avoid any damage to the chip 4 The chip on board Is commonly protected by protecting lacquer use soldering iron to heat protecting lacquer at first heat to 70 80 C then remove the chip after the protecting lacquer is cleaned III Chip welding I Welding time should not be too long to avoid any damage to the chip 2 Soldering iron 1s easy to be oxidized in high temp for a long time clean the head of the soldering iron often to keep it clean 3 Heat transferred by soldering tin when welding put soldering iron head on chip will do no good to welding 4 The chip shall not be moved or quivered before welding concreting 5 When welding SMD weld two diagonally pins to fix chip first then weld others www autoecu com
7. i D No 52000 C66 Character Description VDO we VDO clusters Company _ VDO 99 9 C66 indicate before Sep 1999 C66 Chip it used 93 66 93LC66 C66M3 V1 V2 Fomula NG BORA V1 C86 BORA V2 C86 indicates BORA i has two kind formulas should select the right one Example 99 9 C66 means this cluster made by VDO company before Sep 1999 the chip it used is C66 ODYSSAY V1 C46 means ODYSSAY cluster with IC C46 Use formula V1 2 Select type D Select the type according to the vehicle E g Camry 2 2 Camry 2 4 should select Camry C46 under TOYOTA 2 When several options under a vehicle subject to the chip E g Buick has Buick 68343 and Buick ST14771 under GM If the chip is 68343 use the first one if ST14771 use the second one 3 When several options under a chip Refer to Diagrams and Charts Collection E g Accord V1 C46 Accord V2 L56R and Accord V3 L56R under Honda Chip 93C46 use the first one for chip L56R please see the lt Cluster Adjusting Models Available under Diagrams and Charts Collection first to select as the instruction tells If Import Accord use the second one and for Domestic Accord 2 4 use the third one 3 Resume original data You can resume the original data you saved or select Resume Data operation to resume the data it has tf BL GIT RS WW autoecu com cn 2 Example
8. 0Km it can be adjusted otherwise please contact the manufacturer for solution 6 It has some original data except that the user saved When data lost or using a new chip the original data should be written into before adjusting or the odometer cannot work properly You can resume the original data you saved or select Resume Data operation to resume the data it has 7 Should use the original chip to adjust Use a new one when the original damaged 8 Odometer adjusting flow tf BLEW EATERS www autoecu com cn ADJUST CLUSTER SELECT A VEHICLE CGM SELECT A MODEL BUICK 68343 mw NO THIS RIGHT MODEL HAS THE RIGHT MODEL CONTACT REMOVE THE CHIP MANUFACTURER FROM ODOMETER READ CHIP DATA USE THE ORIGINAL Y CHIP USE A NEW CHIP SAVE CHIP DATA Y Y SAVE CHIP DATA RESUME ORIGINAL Y DATA FAX OR E MAIL CHIP Y NO THE KM THE INSTRUMENT READ OUT 7 ACCORD WITH THE ACTUAL ONE WRITE THE DATA SENT BY YES MANUFACTURER INTO CHIP INPUT KM YOU WANT PUT THE PROGRAMMED CHIP BACK TO THE CLUSTER WW autoecu com cn Hsc egt 25 Gf Remarks 1 Type VDO lt 99 9 C66 ODYSSBY V1 C46 i Y LAJ ATTI l B Al VDO 99 01 VDO Before Year Chip Vehicle Formu la Ch
9. 1 If it displays as below please enter a file name say 0I B When adjusting error occurs browse file 01B to resume the data 12 Select Adjust Cluster and press OK 13 Press number keys 2 S 0 0 0 to enter 25000Km and press to write into Put the programmed device back onto the board after Data Written into Success Example 2 If the cluster cannot work properly need to resume the data 1 Do 1 9 operations as Example 1 the screen display below will come ADJUST KM 2 Press Y and select Browse File then press OK BROWSE FILE 3 Select 01 B and press 4 When Data Written into Success displays data resuming completed 10 7 PISCE 18625 www autoecu com cn Data Resuming For resuming the original data 1 Operation 1 It has some original data except that the user saved When data is lost or using a new chip original data should be written into before adjusting Or the odometer kilometer may display properly but cluster running may be incorrect or car no start 2 Volkswagen with Anti theft II or III system such as Passat B5 Audi A6 Bora and Polo its kilometer and anti theft code are stored in a same chip Resuming the data will make the anti theft code changed so after resuming is completed need to process by trouble coder decoder to start the car All the data may be covered when doing this operatio
10. Km 16 f Hsc egt EAA RS WW autoecu com cn Identify Special Devices Standard and Non standard 93C46 93LC46 LC46 1 C46 has Standard and Non standard most are standard 2 Non standard ones are used in some audios such as Toyota 51703 Mitsubishi 9059 Ceriro CTO16 etc 3 For Non standard chips should select Device Operation 93C series gt Non standard 93C46 to read write VCC NC NC VCC NC CS VSS CLS Standard package pins layout and features Non Standard package pins layout and features On board Pin5 GND Pin7 Null On board Pin7 GND Pinl Null or Pin6 Pin7 Pin8 connect together or Pinl Pin2 connect together Difference between 14pins 93CS56 and 8pins 93C56 1 Chip usually has 8 pins but old Benz C class use 14 pin 93C S56 2 14 pin 93C S50 can be replaced by 8 pin 93C56 connection as below 3 On Universal Adapter has a special area for 14 pin 93C S50 14 pin 93CS56 has 6 null pins 14pins 93CS56 and 8pins 93C56 Chip Replacement 9314 cannot substitute for 93C46 93C46 93C06 cannot substitute for 93C46 C46M6 pe sm xuc and 24C0 cannot ase in exchange _ or 24001 exco 25010 X5045 tf RL EW EVE AS WWW autoecu com cn IV How to Remove and Weld Devices Welding preparation 1 Soldering Iron selection Soldering iron must be connected to a reliable GND If have no constant temperature soldering iron then select the soldering iron of 20W
11. SB Connect Computer Connect Power Supply 12V 4 and 7E0200 Version No creen Delete files Browse Files Rightwards Select items Connect Computer 11 Left Leftwards Backspace Backspace 12 ESC Exit www autoecu com cn BLEW ETERS 7 Il Adapters 1 Normally audio code and Mile Km are stored in the device on the circuit board Put the device onto into the adapter and then connect YH6000 to the adapter to read write the device 1 Chips IC in which stores Mile Km audio code and anti theft code and other CST 35 data Most of them have 8 pins the data 93CSAASI stored In can be read written K 97114 C 2 93 series Chips have Standard and Non standard two kinds More information please refer to the Appendix 2 Two Adapters Universal Adapter and Remove free Adapter or Program on board Adapter Difference between 2 1 Under normal condition the chip should be removed from audio or odometer then use Universal Adapter to read write 2 2 For some odometers whose chip hard to remove such as Honda 2 4 can use Remove free Adapter to adjust without removing the chip from board But only available for those we offer wiring diagrams 3 Adapters Description 3 1 Universal Adapter LED light Insert the adapter it won t turn on when reading the device it turns on 93CS56 14pins For welding 93CS56 14pins Vehicle Speed Signal tee For future use 5 LECCE 1 Some BMW clusters have
12. WW autoecu com cn RL EW EATERS 7 Contents d II Yh6000 Layout and Adapters mH 1 Operation Instructions HH 4 CA 2 Operation eee Hee 4 2 1 Audio Decoding HH 4 22 Odometer Adjusting mem 6 2 3 Data Resuming HH 2 4 Device Operation HH 12 2 5 File Operation mmm 13 2 6 For Audio and Odometer not Listed 14 A AKO UNSSEQUOIITO OUT ES 4 Updating emm Hee 15 IV Appendix eH HH 16 1 Attention for Odometer Adjusting 8 C16 2 Identify Special Chips HO 17 3 Chip Replacement HH 18 4 How to Remove and Weld Device C19 5 Identify Chip Pin s Sequence H 0 20 6 Trouble Shooting 20 WWW autoecu com cn BY 3 ATA ARS 7 Declaration 1 Legal Disclaimer This instrument is intended for lawful service repair in accordance with the laws of the state in which the product is being sold or used NanNing YanHua Electronics Co Ltd sells this product for lawful use only It is a precondition to the acceptance of our company s product that the user shall use this product only in accordance with the laws of the state in which the product will be sold and shall not use the product for any unlawful purposes Otherwise the user shall undertake all the consequent responsibilities 2 The user shall not open the
13. cn RL EW EATERS 7 V How to identify the device pin s sequence Put chip as diagram shown below The first left pin of the bottom IC withacut 10 is Pin 1 The pins sequence is 2 3 4 5 6 7 and 8 in counterclockwise IC with Put chip as diagram shown below the pin near is Pin 1 The pins sequence is P1 2 3 4 5 6 7 and 8 in counterclockwise Put chip as diagram shown below The first left pin of the bottom row is Pin 1 The pins sequence is PI 2 3 4 5 6 7 and 8 in counterclockwise Pay attention to the character IC with character only VI Trouble shooting Possible Causes 1 Select wrong type 2 Chip not well welded Check carefully again Device not well 3 Short between chips connected 4 Adapter not well inserted or Chip error 5 Chip damaged Use another same kind to test ec _ 4 45 e an to read write LLLI wass Instrument Connect Host Long Cannot communicate with the 1 Check if the software open 1 Check for the power supply 2 Check for output It should be 12V Instrument Damaged Send it back to manufacturer for repair No power input No Display 20
14. instrument to avoid any damage to it Otherwise the user shall take all the consequent responsibilities 3 The user should read the User s Manual carefully before using the instrument to avoid any misuse 4 Save the original data before any adjusting operation 5 This instrument is easy to use but the user should pay particular attention to the chip removing amp soldering If not confident in your welding do more exercise with the adapter and spare chips f Hsc egt EAA RS WW autoecu com cn Brief Introduction YH6000 the Data Processor for Automobile Odometer and Audio is an updated product based YH3000A a very popular set among his increasing users After updated large scale vehicles extended and more powerful functions it has It s mainly used for instrument clusters adjusting and audio decoding and also for memory programming Features 1 Handhold operation quick and convenient Connect with computer updating through Internet 2 Vehicles extended most models up to 2004 3 Automatically read out mileage and adjust directly at will 4 USB port Plug and Play 5 Device intelligent identify all devices can use the same socket 6 Can be use as a programmer Let you read save display edit the memory and also send the data back to the manufacturer for technical support 7 Large display screen device data can be browsed and analyzed Body and Adaptors I YH6000 Body 1 25 Pin Socket Connect Adaptor 2 U
15. n and cannot be resumed Important data must be saved first 2 Example Now we have a VW A6 1 8 with barcode 4C0920900 needs to resume the data because of lost data due to a damaged chip Note bar code commonly on the cluster 1 Look up Diagrams and Charts Collection and find 4C0920900 under VW in Data Resuming Original Data to confirm this instrument has original data for this type Put a new chip the original one damaged the chip used 93C86 onto the adapter and note its direction Insert the adapter into the instrument Start the instrument and select Resume Data and press OK RESUME DATA Select VW and press OK select 4C0920900 and press OK 1C0920900 It prompts you Well Connect the Device and the chip used displays Press OK 8 Then it prompts you Save the Device Data Press ESC because it s a new device elle WW autoecu com cn BLL Bll 3 RS Gf 9 The instrument writes the data into this device When it prompts you Data Written into Success press ESC three times to exit 10 You need to adjust the odometer to a wanted kilometer after original data written into Refer to Cluster Adjusting That s to select Adjust Cluster Audi gt A6 VDO 99 01 C86 Adjust Km Input a Km OK 11 Mount the cluster back to car As this car with Anti theft II system the kilometer and anti thef
16. ode should be 118 behind if only o behind indicates the audio can run without any code tz REN 55 www autoecu com cn 1 3 The audio with no symbol behind indicates the code can be changed such as BEI328 1 4 BORO POLO audio can use PASSAT B5 instead to decode 2 Example for decoding Now a BENZ BE1328 needs to be decoded steps as follows 2 1 Look up Diagrams and Charts Collection find the type under BENZ in Audio Decoding IC type to confirm this instrument can do this type 2 2 We can know from Diagrams and Charts Collection that the chip the audio used is DIP 93C46 2 3 Find and remove DIP 93C46 from circuit board then insert the chip into the adapter 2 4 Insert the adapter into the instrument 2 5 Start the instrument and press A V to select Decode Audio then press DECODE AUDIO 6 Select BENZ then Press OK _ MERCEDES BENZ 7 Select BE1328 and press OK BE1328 8 It prompts you Well Connect the Device and displays chip the audio used Press to continue 9 Then the instrument prompts you Save the Device Data You may not save the data because the audio was locked up and press ESC to exit Cif save press OK 10 It will read the code directly after ESC or OK then put this chip back to run the audio with the code obtained 11 If you want to change the code press OK
17. re instructions IV Update 1 Connect it with computer computer should be on line 2 Run the software 3 Start the instrument and press OK within 5 seconds screen displays Connecting Host 4 Click Products Update in software 5 Do as software tells until it prompts you Updating Completed Note Update time is listed on website 15 www autoecu com cn RL EW ETERS 7 Appendix Attentions when adjusting Must save data first before adjusting A cluster commonly has one chip usually 8 pin IC Please note its direction when removing it from board Device can be rewritten times The same type device may use in different cars but the data may be different E g Citroen 988 and Hongqi Century Star use the same kind device X5045 but memory in each is totally different If you want to verify the cluster working properly electrify it as picture shown in Diagrams and Charts Collection Usually the power supply should be 12V but HONGQI 5V For some clusters you need to pull out the cluster hand to remove the chip 5 1 Do not pull those with hairspring that is the hand may return automatically when power off For those hands don t return when power off and return to 0 when power on it can be pull out such as Passat B5 A6 Bora and Polo if no especial instruction 5 2 For BMW 530 and some other BMW clusters with hairspring clamp the rotor to make 1t not move then pull the hand out Or
18. se File Select a filename say 001 OK Coor Derice Read gt Save data mount another chip onto into adapter PY select Browse File Select a filename say 001 OK File Operation To view and delete the data saved 1 Operation User save the data as a file in the instrument when do adjusting operation or other operations Every data has a filename 2 File delete cannot be resumed 3 WW autoecu com cn Gr Gf 2 Example Now you have adjusted an Audi Toyota Camry and Volvo S70 and saved the data in file 001 002 and 003 respectively View Audi AG data Select File Operation Select filename 001 OK E2 View Camry datain Select File Operation Select filename 002 Address Unit 0030 OK F2 1input 0030 OR Only delete Volvo Select File Operation Select filename 003 S70 data Delete select File Operation gt 2 gt For audio and cluster not supported 1 Operation Audio That with IC you can send the data back to the manufacturer to let the technician to analyze or find another same type with a known code copy the data to the one to be decoded then these two have the same codes For those with no IC we need to collect decoding information 2 Cluster For most cars you can send the data
19. t code are In one chip anti theft code will be changed when rewriting original data So need to process by trouble code decoder after adjusting Note Those clusters with no anti theft can work normally again after back to car 12 To process with a trouble code decoder you need to input an anti theft code please contact the manufacturer to get this code Device operation 2 To process the chip that s to read save display edit and copy chip data 1 Operation Modify Display and Modify the data the data will be Memory written into the device while modifying Read device data Write the device data into the instrument Write the data saved in instrument into the device Write all the displayed data into device 2 Example Now we have a 93C46 to be processed 1 Start the instrument press to select Device Operation then press OK DEVICE OPERATION 2 Select 93 series then press OK _ 93 SERIES 3 Select 93C46 and press 93C46 4 The instrument prompts you Well Connect the Device Press OK 5 The screen below comes MODIFY MEMORY 6 On this screen you can do the following operations iier ies Save File OK input a filename say 001 OK data In address PL Qa ais Em to be A8 Select Modify Memory F2 1input 0020 OK A 8 Resume Data Data Select Brow
20. the cluster may be damaged 5 3 Buick Sail hand is easy to damage when pulling 5 4 For Honda 2 0 2 4 do not pull the hand you can make a hole on the plastic 5 5 For Jetta do not remove the motor or it may make the hand wiggle Just pull the hand it may be OK VW with anti theft system 6 1 With anti theft II Passat B5 1 8 1 8T Audi 1 8 1 8 T Bora and Polo 6 2 With anti theft III Passat B5 2 0 2 8 Audi A6 2 4 2 8 6 3 Switch off the ignition before removing the cluster Do not start the car after removing it from car or the anti theft may start 6 4 Select the right type and use the original chip to adjust the anti theft will not start 6 5 When using a new chip or data was lost resume the original data first 6 5 Resume original data you saved and then to adjust the anti theft may not start 6 5 2 Resume the original data in the instrument and then to adjust When putting it back car the anti theft starts need a trouble code decoder For some cars the kilometer Mile stores in two places such as Peugeot Picasso New Benz New BMW Do not try to modify yourself 1f not supported Example You have a Picasso cluster to be adjusted and you have saved data and then to modify it It may display 990 000Km after back to car due to incorrect modifying and now another place will memorize this Km it may be 990 000Km even if you resume the data For BMW with 35080 replace it with a new one if you want a lower

YH6000 user`s manual

Contents

Download Pdf Manuals

Related Search

Related Contents