T2000 Size: 1014kb Last modified: Wed. October 8th, 2014
Contents
1. Frequency Combination Phase lock loop frequency synthesize Rated Voltage DC7 4V Li ion battery Stored Channel 16 channels Antenna Rubber antenna Antenna Impedance 500 Simplex of co frequency or alien fre Operation Mode quency Dimension 120mmx62mmx34mm Weight About 280g Transmit Part Output Power 8W Modulate Mode Frequency modulate Maximum Frequency Offset lt 5KHz Adjacent channel power gt 65dB spurious harrow RF components lt 7 5 uW occupied frequency bandwidth lt 16KHZ Carrier frequency tolerance 2 5ppm Transmit Current lt 1400mA Receive Part Sensitivity lt 0 16uV 12dB SINAD Squelch Sensitivity 0 12uV Audio Power 2500mW Receive Current Squelch System Waiting Current NOTICE lt 150mA Saving your presence no additional notice will be send if specification changes because of technology improving 10 COMMON ERROR AND SOLUTION Error Solution On feedback when turn on the radio Battery power used up please change the battery or recharging Wrong connect of battery please remove the battery and reinstall it The power of bat tery easily get lost The battery life is ended please use new battery Can t talk with other member in the same team Distance is out of the effect communicate range Apply with different frequency DCS CTC SS please reset these2. copy data if the indicator flash unnormal it means copy failed please check whether connect the wire well while the copied radio is light on press MONI button again If you want to copy many radios please turn off the copying radio s power and cut off the wire then change to connect an other copying radio and press MONI button of copied radio to start copy e Quit wired copy you have to re power of the radio then the radio is workable AUXILIARY FEATURES TRANSMITTING TIME OUT TIMER The purpose of the Transmitting time out timer is to prevent any sin gle person from using one channel to transmit for an extended period of time BATTERY SAVING Battery saving makes the transceiver cut down receiving circuit to decrease power consumption and longer use time when these is no signal BATTERY ELECTRICITY NOTICE Low battery power alert will note you to charge the battery In case the battery has fully charged the light will turn to red In case you hear beep the radio will stop transmit please change a new battery or charging the battery ALARMING FUNCTION Press alarm knob 2 seconds to enter the alarming function if while alarm the channel has set the transmit frequency the radio will auto transmit alarm voice You can press alarm knob to cancel the alarm function SPECIFICATION General Part UHF 36 173 995MHz VHF 400 479 995MHz Temperature Range 10 C 60 C Frequency Range
3. grooves at the bottom of the battery pack with the corresponding guides on el the aluminous frame on the back of the transceiver Slide the battery pack upon until hearing a clatter Please turn off the transceiver first be fore removing battery pack Push bat tery latch on the button of the transceiv gt er then pull away from the transceiver INSTALLING THE BELT CLIP Use two accessory screws fixing belt clip to make it convenient to take if necessary BASIC OPERATION POWER ON OFF Turn the Power Volume knob clockwise to switch on the transceiver you will hear a beep Turn the Power Volume knob counterclockwise to switch off the transceiver ADJUST VOLUME Turn the Power Volume knob clockwise to increase volume and turn it counterclockwise to decrease volume If you can t hear background noise because of squelch system please hold MONI button then turn the VOL control knob You can hear background noise when press MONI button FREQUENCY SELECT While you switch the channel the voice remind your selected channel number if you didn t set the frequency you will hear the beep TRANSMIT RECEIVE Press PTT button and speak normally when transmit preparation is ready The transmit indicator lights red after enter transmit mode It may increase distortion if you are too close to the MIC or speak too laud and this may cause you voice unclear by receiver Rel
4. THANK YOU We are grateful you have chosen FM VHF UHF portable transceiver This 2 way radio represents novel design and stable performance It is developed to meet the demands of portability easy operating and multifunction Believes the small size and the reasonable price will satisfy your requirements SAFETY INFORMATION SAFETY It is important for you to read the following carefully in order to use this transceiver safely and efficiently Please DO NOT try to open the transceiver Modified by laypeople may do damage the transceiver Please turn off your transceiver when you enter the place with the sign Please turn off radio such as hospital and other medical care place to avoid electromagnetism interfere or electromagnetic compatibility Please turn off your 2way radio when it is requested by aircrew on the plane Please DO NOT put the transceiver in the area of airbag if you are in a car with airbag Please TURN OFF your transceiver before entering flammable and exposable place Please DO NOT use broken antenna Broken antenna might cause slight burn if it touches skin Please DO NOT expose the transceiver to direct sunlight for a long time DO NOT place the transceiver near any heating devices Ei ther high temperature might shorten the life of electrical parts and also might cause some plastic transform Please DO NOT put the transceiver in dusty or dirty place Please keep the transceiver dry Rain and damp
5. ease PTT button when the talk is over and the mode will turn back to receive 5 CHANNEL EDIT PC Program Connect the program cable to the radio and well connect the com puter COM communication port and SP MIC jack by program cable turn on the radio at the same time Turn on the computer and open the radio program soft Then se lect the using frequency and other function parameters which you re quired Afterward press the Edit write to radio or directly press the relative signal on the toolbar to start writing After the progress bar finished the screen will display Succeed All the parameters on the screen have written in the radio Wire Copy Take out a programmed radio while using a special data copy cable to connect to another radio which you want to copy data e The radio was copied should turn to channel 8 Press PTT but ton and Function button and switch on the radio at the same time you will hear a beep in 5 seconds release the Function but ton The red light will on which means under the copy mode Using a special data copy cable to connect the SP MIC jack of two radios Firstly turn on the coping radio While everything is ready the copied radio is light on Press the MONI button to enter copy mode the light of copied radio will shows red and flash the light of coping radio will shows green and flash The light of copied radio will shows red while the copy has finished While
6. may erode the PCB If an abnormal odor or smoke is detected coming from the trans ceiver TURN OFF the power immediately and remove the re chargeable battery pack from the transceiver and contact with your dealer CHECKING EQUIPMENT Thank you for using T30 transceiver Before using we recommend you e Please check whether the package is broken e Unpack the transceiver carefully Identify the items listed in the following table If any damage or miss has occurred during shipment contact with dealer immediately SUPPLIED ACCESSORIES ITEM QUANTITY Antenna 1 Li ion Battery Desk Charger Adapter Belt Clip User Manual i i i i MAIN FUNCTION VHF Frequency Range 136MHz 173 995MHz UHF Frequency Range 400MHz 479 995MHz 16 Stored Channels CTCSS DCS Alarming Function PC program Wire Copy Function Chinese English Channel Number Voice Annunciation CONTENTS GETTING ACQUAINTED uussnsssnnnennnennnnunnnnnnnnennnennnnunnnnnnnnnnnnnnn 1 PREPARATION uesusssnnssnnnennnnunnnunnnnunnnnnnnnunnnnnnnnennnnnnnnnnnnnnnnnnnnnnn 3 Charging Battery Pack iii 3 Installing Removing Battery Pack wand Installing the Belt Clip bei 4 Power ON OF Fic iscesissicaseessssccnszsaateascsieacpcopassici AA A A aires 5 Adjust e 5 Frequency Select Transmit Receive BASIC OPERATION CHANNEL EDIT vestscscccccesessrssctsaciesscsivsercsatsascesstserscceessersvesesteases Tra
7. nloading frequency line and use software to download Speaker Output voice Belt Clip Clip the transceiver to you belt making it convenient to take Battery Pack 3 7V Li ion battery pack PREPARATION CHARGING BATTERY PACK The battery is not charged in the factory and please charges it be fore using The first charging can t reach full capability after buying or storing for a long time more than two months Please charge and discharge it for two or three times to make real capability reach full capability Plug the uncharged battery or transceiver with battery into char m I S 7 d U ger and make sure the battery contact with charging terminal When the charging light turn red charging has begun and while the charg ing light turn green charging has finished Please do not keep charg ing over 20 hours please pull out the plug while finished charging NOTICE e Please do not charge the battery again if it is charged fully otherwise the life of the battery will be shorted or it will be damaged e Please turn off the transceiver before charging It may disturb charging if you use the transceiver when charging It comes to the limit of the battery life if the use time of transceiver shorten obviously even charging is correct Please change new battery pack INSTALLING REMOVING BATTERY PACK Match two juts on the top and two
8. nsmitting Time Out TimMer cccccccssccsscsssseseesecsatisescesatsrseerecesds 8 Battery Saving ici rra 8 Battery Electricity Notice ep Alarming Gilet 8 AUXILIARY FEATURES uuuuusnussansnnnnnennnunnnennnnennnnunnnnnnnnunnnnnnnennnn 8 SPECIFICATION EE 9 COMMON ERROR AND SOLUTION uuuusnnrsonnennnnennnnnnnnnnnnennne 11 FREQUENCY INFORMATION LIST nuussnsssnnnenneennnnennnennnnnnnnne 12 GETTING ACQUAINTED Antenna all Power Volume Transmitting Receive Indicator Speaker Knob Microphone PTT Transmit Firce to Receive MONI Earphone Slot PC Program Slot Antenna Rubber antenna used to receive and transmit signals Transmitting Indicator Lights red while transmitting Receive Indicator Lights green while receive Power Volume Knob Turn clockwise until a clatter to switch on the transceiver Turn counterclockwise until a clatter to switch off the transceiver Rotate to adjust the volume PTT Transmit Force to Receive MONI Press to get into transmits state re lease to return to receive state Press to receive signal or noise in the channel your selected when in receive state Alarm knob Press this knob 2 seconds then the radio will alarm Microphone Input voice Earphone Slot PC Program Slot Connect with external earphone or connect to PC by dow
9. parameter Appears voices from other non member 11 Please change your CTCSS signal or change all the transceivers signal in your team FREQUENCY INFORMATION LIST Model No Serial No Transmit Receive Frequency Frequency 12
Download Pdf Manuals
Related Search