3 control with a dmx512 controller
Contents
1. A E T 1 e When Dimmer is set to OFF the RGB and Master Dimmer are linear 1 4 PHOTOMETRIC DATA 2 e When selecting DIM11 DIM21 DIM3 or DIM4 the RGB and Master Dimmer T5 SAFETY WARNING iti br op ER ERE 2 are nonlinear e These4 dimming modes have different soft and smooth dimming effects from fast to slow PART 2 Ihm ttt ttt ttt tt 3 2 1 MOUNTING Pain dau sobre Pre Padua 2 2 2 WIRING amp 4 2 J ADJUST THE BEAM ANGLE 4 2 4 POWER 5 4 9 STATIC 2 5 SIGNAL CONNECTIONS ccccccceececcceccecccecceecesceeceseaecneensseneees 5 U gt ea gt 0 255 2 6 SETTING UP WITH A DMX512 CONTROLLER 6 MENU gt Gu 2 7 SETTING UP WITH THE PiX 6 Gren J 0 255 Blue 0 255 Strb 0 20 PART 3 CONTROL WITH A DMX512 7 EMED gt CA 3 1 CHANNEL ASSIGNMENT iusso estu ssa assu siia eb ero aene i 3 2 BASIC INSTRUCTIONS FOR DMX512 9 STATIC e Enter the STATIC mode to create the programs2. CHANNEL 1 2 3 4 5 FUNCTION RED GREEN BLUE FUNCTION MASTER DIMMER RED GREEN BLUE FUNCTION MASTER DIMMER RED GREEN BLUE COLOR MACRO NO FUNCTION RED 100 GREEN UP BLUE 0 RED DOWN GREEN 100 BLUE 0 3 CONTROL WITH ADMX512 CONTROLLER 7 2009 7 21
3. PART 4 USING THE DMX CODER eene 10 e Combine RED GREEN and BLUE to create an infinite 4 1 TECHNICAL SPEGIFICATIONGS En on reo Fond ead o xo ao ede oaxe 10 range of colors 4 2 SETTING PARAMETERS 10 e Setthe value ofthe STROBE 0 20Hz d BASIL em EE 11 e The static setting will be valid when the fixture is powered again 4 4 MENU seuil PI LIP 11 4 5 DMXADDRESS uueccccssccssecssccssecsecssccsscssccssccssnesccssaensnnsnassnaeeas 12 4 6 PERSONALITY 1 2 4 7 CALIBRATION 12 4 8 DIMMER 13 BS TAT IG 13 PART 5 yt tre 14 D I TNOUBEE SHOOTING esi orte nt REP e ta ttr id d RR add 14 5 2 14 4 USING THE DMX CODER di 2009 7 21 45 DMXADDRESS 1 PRODUCT GENERAL MENU Je je 1 512 DMX 1 1 PRODUCT INTRODUCTION This productis designed for outdoor architectural applications It be operated both asa e Enterthe DMX mode to set the DMX address press Enter single unitand multiple units for large applications e On successful setting the fixtures will display Green and turn off after ten seconds e f an error occurs when setting the fixtures will display Red or no response 1 2 PRODUCTFEA TURES 4 6 PERSONALITY LED FIXT
4. 9 APPENDIX 5 7 TROUBLE SHOOTING 1 DMX signal cable error LED MODULE SITUATION Can not receive 2 Signal connection error DMX signal 3 The input signal 4 DMX address error Color mixing 1 LED not joining well uneven with splash 2 Lens not installing well Partial color 1 The current of one color LEDs is partial red partial strong or too weak green or partial blue 2 LEDs brightness not LEDs of the same 1 LED or Main PCB damaged color are not lit 5 2 MAINTENANCE 5 APPENDIX ACTION 1 Check all signal cables 2 Check all signal connections 3 Check the input signal IC 4 Check DMX address 1 Check LEDS joining 2 Check lens installing 1 Check drive current of each color in Main PCB 2 Check LED quality 1 Replace damaged LED or Main PCB No ITEM 1 Stainless steel cover 2 15mm template glass 3 Diaphragm 4 LED Plate 5 LED PCB 6 Heat sink 7 Power switch 8 Control board 9 Inner housing 10 Outer casing 11 Dustproof board 2009 7 21 EX POLITE TerraLED USER MANUAL Version 1 0 4 8 DIMMER MENU orr ABLE OF CONTENTS Dim DIM2 DIM3 PARIT PRODUCT GENERAL pax EE a npn ERE ER 1 DM4 1 1 PRODUCT INTRODUCTION es 1 DIMMER 1 2 PRODUCT FEATURES 2325232222222232322222523222222222222 3223222 32222222 822222232233 1 Enter the DIMMER to select the dimmer work mode press Enter 1 3 TECHNICAL SPECIFICATIONS
5. L SPECIFICATIONS LED MODULE Battery 2x1 5V DC Dimensions 110x 70x 28mm Weight 0 2Kg 4 2 SETTING PARAMETERS Connect the DMX Coder to the units in series Set the DMX address Personality Calibration and Dimmer of fixtures through the DMX Coder A maximum of 20 units in series can be set by the DMX Coder at the same time All connected units will be set with the same information Power DMX OUTPUT 1 GND 2 Data 3 Data 1 GND Black 2 Data Green 3 Data Red Signal Connector Note The DMX Coder will automatically power off after extended periods of being idle 1 minute 4 USING THE DMX CODER 10 2009 7 21 2 INSTALLATION 2 1 MOUNTING Embed the outer casing first before installing the fixture NOTE The stainless steel cover should not exceed the ground NOTE When installing the collar ensure that one of the cable outlets is perpendicular to the target illumination surface Concrete Drainpipe Hardpan 3000kg The fittings have been designed and tested to withstand static of 3000kg based on the outer casing for installation exclusivelyin pedestrian or bicycle areas 2 INSTALLATION d 2009 7 21 2 2 2 INSTALLATION 74 2009 7 21 WIRING DIAGRAMS e Unscrew the junction box and remove the cover Fetch the terminal for cable connection e Put the cable 6 5 8mm throught the junction box e lighten the termi
6. MX512 CONTROLLER 9 2009 7 21 CHANNEL VALUE FUNCTION 70 RED 0 GREEN100 BLUE UP 90 RED 0 GREENDOWN BLUE 100 lt gt lt gt 91 lt gt 110 RED UP GREEN 0 BLUE 100 lt gt 130 RED 100 GREEN 0 BLUE DOWN lt gt 150 RED 100 GREEN UP BLUE UP 151 lt gt 170 RED DOWN GREEN DOWN BLUE 100 171 lt gt 200 RED100 GREEN100 BLUE100 WHITE 100 WHITE 1 3200K 206 lt gt 210 WHITE 2 3400K lt gt 215 WHITE 3 4200K 216 lt gt 220 WHITE 4 4900K lt gt 225 WHITE 5 5600 WHITE 6 5900K N N N C2 eo WHITE 7 6500K Co oO WHITE 8 7200K N C2 IA e AR 2 AR WHITE 9 8000 N O N O1 e WHITE 10 8500K 251 lt gt 240 WHITE 11 10000K STROBE 6 0 lt gt 9 NO FUNCTION 10 lt gt 255 FROM SLOW TO FAST DIMMING SPEED Return to DIMMER 29 OFF Dimmer speed off 69 DIM1 Speed 1 the fastest lt gt lt gt 70 lt gt 129 DIM2 Speed 2 lt gt lt wo e 189 DIM3 Speed 3 190 lt gt 255 DIM4 Speed 4 slowest SOLID CHANNEL VALUE FUNCTION 1 0 255 RGB amp MASTER DIMMER 3 CONTROL WITH ADMX512 CONTROLLER 8 2009 7 21 2 4 POWER CONNECTIONS The input wires of this product must tri core as folowing L Black N White E Green L Black N White E Green Junction box Junction box 2 5 SIGNAL CONNECTIONS Pins a nd F
7. URE MENU PERSON gt ARCI RGB dimmer 0 100 ARC14D Color macro ARCFULL ee robe Dimmer speed control CORRAN Static Function PERSON DMX512 control Compatible with the PiX Controller e Enter PERSON and select ARC11 ARC1 D ARC FULL1 REMOTE Lightweight aluminum casing SOLID mode press Enter IP67 protection rating e When selecting ARC 1 ARC1 D ARC FULL SOLID the fixture is under the DMX work mode e When selecting REMOTE the fixture is ready to receive signals from the PiX Controller 1 3 TECHNICAL SPECIFICATIONS LED MODULE 4 7 CALIBRATION Volt AC100 240V 50 60H MENU gt caus je WHITE Red gt 0 255 oltage 2 WHITE2 0 255 Rated Power 46W Blue 0 255 IP IP67 PROTECTION TING LED Unit 12pcs tri color WHITE11 Output LED 3w RGB CALIB Environment Temperature 20 C 40 C Cooling Direct air convection Enter the CALIB to select white colors of different color temperature Dimensions 320 x146mm There are 11 pre programed white colors plus RGB and can be edited by using Red Gren Blue press Enter to setthe values While working under ARC FULL WHITE1 9 means the different color temperature white 1 to white 9 of CH5 Select RGB to set theratioof Red Gren and Blue on DMX channels 320mm achieving different white colors Weight 8Kg 146mm 4
8. USING THE DMX CODER 12 2009 7 21 1 PRODUCT GENERAL 1 2009 7 21 1 4 PHOTOMETRIC DATA 4 3 BASIC a 801 159 71 41 3 28 LUX GREEN 1240 155 163 96 67 LUX POWER Power on AHAAA 2 MENU 1 Scroll through the main menu or exit from the LLa current sub menu press and hold turn off power ENTER Enter the currently selected menu or confirm the current function value DOWN 1 Scroll DOWN through the menu list or decrease the value of the current function UP Scroll UP through the menu list or increase the value of the current function Y 6 4 6 10Distance m 1 5 SAFETY WARNING IMPORTANT aM dd o _ 4 4 MENU ALWAYS READ THE USER MANUAL BEFORE OPERATION PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE MENU Je wx je 1 512 SAME AS THE MAINS POWER SUPPLY IN YOUR AREA p 1 0 e This product must be installed by a qualified professional e Always operate the equipment as described in the user manual e A minimum distance of 0 5m must be maintained between the equipment REMOTE combustible surface SOLID e The product must always be placed in a well ventilated area e Always make sure thatthe equipmentis installed securely CALIB z WHITE gt Red gt 0 255 e DO NOT stand close to the equipment and stare directly into the LED light source WHITE2 Gren 0 255 e Al
9. nal with the cable according to the instruction e Screw the junction box Terminal Data GND BLACKZ22 Live BLACK 18 TO D Data GREEN 22 Earth GREEN 18 Jj Data RED 22 Neutral WHITE 18 LI BH dU NOTE The bolts that secure the frame to the body must be fully tightened in a uniform manner altermating between diametrically oposed bolts To facilitate the extraction of the glass without damaging the seal fitted onto the frame unscrew all the nuts except for two adjacent ones and wait a few seconds then unscrew the remaining nuts and remove the glass 3 2 BASIC INSTRUCTIONS FOR DMX512 OPERATION ARC FULL MASTER DIMMER e CH1 controls the intensity of the currently projected color e When the slider is at the highest position 255 the intensity of the output is the maximum RED GREEN amp BLUE COLOR SELECTION e CH2 CH3 amp control the intensity ratio of each of the RED GREEN BLUE LEDs e When the slider is at the highest position 255 the intensity of the color is the maximum e CH2 CH3 CH4 can be combined together to create over 16 million colors COLOR MACROS e CH5 selects the required COLOR MACRO e CH5 has priority over CH2 CH3 CH4 e CH1 is used to control the intensity of the COLOR MACRO STROBE e CH 6 controls the strobe of CH1 to CH 5 DIMMER SPEED e CH 7 is used to select the kind of dimmers curve required 3 CONTROL WITH AD
10. un ction s Itis advised for greater stability that if over 20 units to be connected or _ the total signal cable length is over 60 meters a DMX signal amplifier should be used Signal IN Signal out Junction box Junction box Pins Functions Pin1 black 2 green Datainput Pin3 red Data input 2 INSTALLATION 5 s 2005 7 21 2 6 SETTING UP WITHADMX512 CONTROLLER Connect the units in series using standard DMX cable or IP 67 cable provided Set DMX address using a DMX coder Each DMX Address may be used as many times as required Any DMX address inthe range from 001 to 512 may be used Connect the DMX512 controller to the units DMX Adar 1 DMX Adar 8 DMX Adar 15 DMX512 CONTROLLER The figure above shows a simple DMX512 layout with the starting address ofthe first unit set at 1 with the second set at 8 and SO On 2 7 SETTING UP WITH THE PiX CONTROLLER The fixture can also be controlled by the PiX Controller set the fixtureas REMOTE via the DMX coder before using the PiX controller Note For details please refer to the user manual of the PiX controller PiX Controller 2 INSTALLATION bs 2009 7 21 3 CONTROL WITH ADMX512 CONTROLLER 3 1 CHANNELASSIGNMENT e Note This product has five DMX512 channel configurations ARC 11 LARC 1 D ARC FULL SOLID ARC 1 CHANNEL 1 2 3 ARC1 D CHANNEL 1 2 3 4 ARC FULL
11. ways disconnect the power supply before attempting maintenance Blue 0 255 e Always make sure that the supporting structure is solid and support the combined weight of the products WHITE11 e The earth wire mustalways be connected to the ground RGB e Do not touch the power cables if yourhands are wet DIMMER gt OFF DIM1 _ DIM2 ATTENTION DIM3 DIM4 AATTENTIONA STATIC Red J 0 255 Gren 0 255 e This product left the place of manufacture in perfect condition In order to maintain this Blue 0 255 condition and for safe operation the user must always follow the instructions and safety D gt warnings described in this user manual e Avoid shaking or strong impacts to any part of the equipment e Make sure that all parts of the equipment are kept clean and free of dust e Always make sure that the power connections are connected correct and secure e If there is any malfunction of the equipment contact your distributor immediately e When transferring the product itis advisable to use the original packaging in which the product left the factory e Shields lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired e The lamp LED shall be changed if it has become damaged or thermally deformed 1 PRODUCT GENERAL 2 2009 7 21 4 USING THE DMX CODER 11 2009 7 21 4 USING THE DMX CODER 4 1 TECHNICA
Download Pdf Manuals
Related Search