Home

Installation manual

1.
2. 1 Open the Entro gt 76 application 2 Click the Time schedules tab 3 Click New 4 For new time schedules a wizard is invoked which will help you configure the required functions For existing time schedules the tabs are shown displaying the same information The wizard also directly allows for configuring of Half days Holidays and Holiday periods See Enter public holidays and holiday periods 5 In the Name field enter the name of the time schedule e g Training sessions Click New to create a new Interval A row with suggested fields with From To and Weekdays is displayed 7 Click on the arrow at From and choose time Press TAB 8 Click on the arrow at To and choose time Press TAB 9 Select the Days when the interval should be valid 10 Repeat step 4 7 for every new interval 11 You can click on Sort to get the intervals sorted 12 Click OK to save the time schedules Set up information for the next time schedule in the same way 106 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 5 Reservation object Below describes how to configure the Reservation object itself The definition of physical doors relays for the single or grouped object is initially done in the Installer gt 76 application 1 15 16 lf more than one Member class shall be used go to the folder Person settings in the
3. 5 2 Local DC Power Supply Whenever using separate power supplies for SiPass Entro for one or several readers it is very important to wire all minus OV cables together This is because the RS485 communication interface uses the minus potential as a reference If there is voltage differences between the units there might be unwanted disturbance of the communication Be sure that the PSUs have a stable voltage output Even if the SiPass Entro system components are tolerant to voltage fluctuations the locks may be more sensitive Also remember to use enough area of the power cables especially if there are long distances involved Below is an example of a 12V application where the SR35i is powered with a local power supply oD SR35i DC12 DC22 Local Power Supply 39 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Power supplies 5 3 Voltage drop 40 SiPass Entro tolerates voltage levels down to approx 10V DC for working whilst a 24V electrical lock might have a tolerance of maximum 15 which means that the voltage cannot drop below 20 4 V DC The calculation of voltage drop in cables is achieved by using Ohms law which States Resistance Ohm x Current A Voltage V The parameters affecting the voltage drop are as follows Cu
4. 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 FAQ the SR35i to see the effects of the information quantity Both UDP and TCP This is however not quite so dramatic relative to a 100 Mbit LAN Why not use VLAN VLAN is a good alternative to create a more secure network It is however difficult to state general recommendations how to build the users own LAN There is no reason for using VLAN due to network load in a SiPass Entro TCP IP environment In general we recommend IT managers to use LAN switches rather than a SiPass Entro recommendation Can database files be placed on a LAN server to make it possible making backups in night time There are three main methods for central backups 1 Each user modifies the path in the file dbpath ini on the local PC to store the database files on his her unique server folder rather than in the local PC You then must of course be sure that the server is running all the time In this solution each user also connects to the SiPass Entro system 2 Use SiPass Entro terminal server client solution where both the files and the connection are done centrally 3 If a Windows domain and a server based profile storage is used the database is automatically stored to a server share with every logout off the PC The way SiPass Entro is designed there is also redundancy integrated in the database because all data is stored in every SR35i except events handshaked from the PC Is the
5. 99 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Configure other type of zones 25 Configure other type of Zones G In the same way as an alarm zone is created one or more doors can form another type of zone These could be Anti pass back zone Roll call Zones Entrance limitation Zones Interlock zone two doors You can also use sub addressing technique when creating zones and selecting readers This applies to reader tyoe BCLINK who can be addressed as ENTRY or EXIT when connected to the same door central 25 1 Anti pass back Roll call 100 As an anti pass back zone is created a roll call zone is created as well You can however create zones that are roll call Zones only The only difference between roll call and anti pass back is that anti pass back means that the card will be black listed if a person does not use his card to leave a zone he has previously entered The same reader can be an IN reader to one zone and an OUT reader to another This is how to create an anti pass back or roll call Zone 1 Open the Installer gt 76 application 2 Click the Zones tab then New For new zones a wizard is invoked which will help you configure the required functions For existing zones the tabs are shown displaying the same information Tip You can also right click and choose New Edit or Delete 3 Type the name of the zone in the Nam
6. An example of random function might be a laundry room with a couple of washing machines where each is an object which will be controlled by a relay in an IOR6 machine control All these individual objects are then grouped together and can be treated as one common grouped object The users are then allotted some of these individual objects when a reservation is done To create a grouped zone 1 Create the individual objects as above 2 Select the same Main Reader for all objects 3 Select an IOR6 relay as machine control to control the object e g a washing machine 4 Finally you create a new object but select Group of Reservation Objects instead and mark the actual objects to group Note that a common main reader for more than one reservation object will only work if the objects are grouped together Doing this will result in the main parameters e g the maximum number of reservations being the same for all objects 26 3 Alarm control in a reservation object If you install an intrusion alarm in premises that are also using reservation you can use the card reader for alarm control in both Monostable and bistable mode You use a DC22 for this Monostable mode This method requires that the DC22 used in the door must be configured for Monostable mode In the tab Relays in the door properties of the Installer program mark the tick box Use the relay for alarm by pass The alarm by pass relay will change state during the
7. Maintenance 2 4 Software update in existing system The version 6 5 supports a migration path from version 4 5 and later The new version may include updates for the following components PC equipment SR35i e SR34i no radio but adoption to version 6 5 level Door controllers Before you begin Verify which version of the existing PC software not earlier than 4 5 Verify that all Segment controllers are of type SR35i or SR34i If any SR32i exist these must be changed to SR35i This may also result in that some functionality e g common alarm must be moved to an IOR6 controller instead The following table matrix gives the relevant possibilities for software versions and Segment controllers Ver 4 5 Ver 4 7 Ver 5 x Ver 6 0 Ver 6 5 SR35i No Yes 1 2 Yes 1 Yes Yes SR34i No Yes 2 Yes Yes 1 Yes 1 SR32i Yes Yes No No No 1 No wireless RF30 functions 2 No common alarm relay in the segment controller To upgrade to the latest software version do like this 1 If the existing PC version is 4 7 or older first replace all SR32i with SR35i Then check that all segment controllers firmware platform is version 5 Simplest by using the menu system in the controller If the switching menu does NOT appear in the controller this means that the controller has been updated to a firmware that instead supports updates from the PC 2 Insert the CD in
8. 13 6 5 Additional considerations for the AX For AX4 Lite AX4 160 100 and AX9 AX16 250 50 the following settings must be performed No recording configuration in the time lapse recording setup At AX9 AX16 250 50 the REC button has to be activated on the AX device For AX9 AX16 250 200 the following settings must be performed Inthe Schedule screen the recording mode has to be set to Event For AX16 the following settings must be performed The record button has to be switched on Inthe network settings the Transfer Control has to be switched on When the parameters are configured enter them into the SiPass Entro Installer application when creating connections and cameras 13 6 6 AX Live Viewer software Note that only one live view window at a time can be displayed using the AX Watch remote software This means e g that if SiPass Entro is displaying a view in the Installer when setting up a Camera you cannot concurrently view an image in the Door Monitor by clicking on a camera icon In RAS v3 5 and above the separate applications AX Admin AX Watch AX Search are integrated into one user interface 13 7 SISTORE CX 13 7 1 General 72 The CX model uses PC software module for configuring and viewing Read more in the Quick setup or the DVR Configuration manual We recommend that the SX CX software is installed on the C drive Note that the CX includes an integrated homepage which can be brow
9. function 91 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Configure OR6 relay controller 23 Configure IOR6 relay controller The relay controller can be used for a range of special functions These are at the moment Door lock monitor output Common alarm pulse output Time control output Monitoring a power failure signal e g battery input Monitoring an Emergency opening signal to open selective doors input Exit button function Input for activating a relay Reservation functions Lift control i Common alarm is not possible in an IOR6 used for lift control applications You must use another IOR6 in these cases The settings for this you find in the Installer Doors where you mark the actual IOR6 or create a new There are separate tabs for relays and inputs 23 1 Door lock monitor output The lock monitor function can be used for monitoring that selected doors are unlocked e g emergency exits Proceed as follows 1 92 DO Op 2 Y Open the Installer gt 76 application Choose tab Doors and mark an IOR6 Click Edit Mark the tick box for lock monitor in the tab IOR Relays Select the lock monitor function for any of the relays Click on the button to the right of the list box gt A new window with a door list is displayed Select which doors to be monitored Building Technologies F
10. 2010 30 Index A Access Control 10 Alarm Status Feedback 45 98 Alarm zone 97 Alarm Zones 44 Anti pass back 42 43 100 AX 70 B BAPSI 32 Bistable function 98 C Cancel time 107 Card printing 10 Card reader parameters 81 CCTV 10 CF8 64 120 Client 25 Clock 66 Common alarm 93 Concurrent Reservations 107 Confirmation 113 Connection 55 117 Connections 66 Crypto key 115 CX 72 D Database 24 55 117 120 DC800 121 debit 111 Detection of units 57 DHCP 49 87 90 DNS 49 Door controller 91 Door Monitor 10 Door monitor contact 42 Door Monitor Contacts 91 Download 121 Index Dynamic DNS 49 DynDNS 51 52 E E mail 111 E Mail Server 87 Emergency opening 94 Entrance limitation 101 Entro 10 Entroser 78 ENTRY reader 43 ESD 118 Ethernet 25 EXIT reader 43 Expansion 115 external time server 80 F Factory crypto key 115 Firewall 52 Firmware 120 Forward reservation time 107 G Gateway 86 Grouped object 105 H HTML 64 InfoPoint 10 29 Init string 61 Installer 10 Interlock 102 Intrusion 10 44 45 IOR6 95 IP address 86 L LED 82 License 24 117 118 License number 58 Duress 82 Lift control 95 DVR 31 65 kaca vag ocal power su DVR type 66 ii 127 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Index Loc
11. 3 11 4 11 5 12 13 13 1 13 2 13 3 13 4 13 5 Central DC power supply cccccccccsscccceeeeeceeceeceeeeceeesseeeeseaseeseaeeeseeeesseneess 38 LoGal De Rower SUD DIY ssscis f sts Ma seets hele ete he adisa ets Seda 2b 39 NW OMAGC GRO esrara a macdsdmandi cals 40 Example of a typical power supply SECTION ccccceecceceeeeeeeeeceeeeeeeeeeeaees 41 Several DC power supplies in the same cable section ccccceeeeeeeeeees 41 SPEClal INS tall AMOS iiaae a a aa aaa eaaa aA aa AAE EEEN 42 Anti pass back using BCLINK readers cccccseeceeeseeeeeeaeeeeeeaeeeeeeeaeeeeeeas 42 Anti pass back using Clock amp Data and Wiegand readers ccceseeeeeees 43 Intrusion Alarm Zones With DC22 000 cecccccccccceeccccececseeceeeeeeeaeeeeseeeeseeeeesees 44 Connecting Alarm Status Feedback in DC22 ASF ccccceeceeeseeeeeeeeeeees 45 Quick start guide csik a eae ei 46 Connect the PCs or an online printel ccccsseeessseeeeeeeeeeeeeeeeneeseeeees 47 Connect PC via Local Area Network ccccccceccecseeeceeeeeeeeeeseeeeesaeeeesaeeeeas 47 Connect PC with direct cable RS232 cccccccccccseeeeeeseeeeeeeeeeeeeaeeeeesaaeeees 48 Connect an on line printer R8232 ccccccccseeeeecceseeeceseeecseseeeseeseesssaneees 48 Prepare any network reSOUICES ccccceeeeeeeeeeseeeeseeneeeeneeseeneeseenenseneeneaaes 49 Background zsrsr a iui vaneteetuadiedetonrsmetuna
12. Access Control System are not so many 46 Below is a list of issues to perform to quickly get the SiPass Entro system work Install software in the PC gt 55 Set time amp date gt 79 Configure names for segment controllers gt 83 amp Configure SR35i gt 86 Decide on time functions Configures names and functions for doors gt 91 amp Configure doors Configure Access groups Logging on card holders Card printing Configure System users Access registration Viewing status amp events If you intend to use other functions please read appropriate sections for further information Intrusion alarm control gt 97 DVR integration amp Camera control Reservation functions To be found in other documents Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Connect the PCs or an online printer 8 Connect the PCs or an online printer 8 1 Connect PC via Local Area Network By using the Local Area Network you must confirm with the IT Manager the correct P addresses and installation settings for the system 1 Connect the Ethernet cable to the PC and the Local Area Network 2 Connect the Ethernet cable to the SR35i and the Local Area Network SR35i Cat 5 Cat 5 Ethernet 10 100 Mbit TCP IP Example of connecting a PC via Local Area Network Install a dummy network It is also possible to form a du
13. LED Control to define how the red LED at the door terminal will be controlled Either the LED is controlled by the feedback signal or another external signal could be connected This is the case if the red LED needs to flash in some way If choosing ASF you optionally also can disable the red LED after a certain time after alarm activation In this case the LED will light only on the reader where the command is performed Any other reader LED in the zone will be off If you do not choose the ASF function an external signal could still be connected In this case choose only LED Input If you click on Adjust at LED input you can adjust the time to determine if the external signal from the alarm system should light or flash the red LED on the door terminal Default and maximum value is 3 2 seconds If it should flash this period should be slightly longer than the pulse cycle of the external signal Click OK Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Contigure Intrusion Alarm zones 24 1 Decide on security levels for alarm control G 1 Open the Entro gt 76 application Click on Zone tab Click on Settings Select the security level for activating and deactivating the intrusion alarm Click on the list box and choose Card or Card PIN Click OK oF e amp P This selection will be set for all Alarm zones you create
14. Opening time the Door Held Warning Time and will the automatically fall back Bistable mode Note that this method differs somewhat from the way SiPass Entro normally treats intrusion alarm control within alarm zones This mode will arm or disarm an alarm section in the intrusion alarm Connection is done to the alarm by pass relay in the DC22 Be sure that the tick box Use the relay for alarm by pass in the Relays tab is not marked 105 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation i The actual zone in the intrusion alarm can only be managed from this door Activation is performed with an alarm button connected to the Alarm button input of the DC22 Deactivation is accomplished by a granted access to the reservation object Usually the security level Card or Card PIN will apply 26 4 Time schedules The first thing to do is to identify the times for reserving In tennis court there may be three hour sessions which can be booked all the week around or some other object only available on weekdays In the system there can be 32 time schedules with each 24 intervals for reservation i The clock and day values below forms the basic intervals but it can be modified in some aspects by the time shift concept You add this function in the Installer program when configuring the doors in the reservation object zone
15. SR35i HTTP port 80 when using reservation via Internet 4011 for TCP when several SR35i communicates through LAN SNITP port 123 for fetching correct time if SR35i uses TCP protocol between each other Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 4 1 Recommended system cables G System requirements The table below shows what kind of connections could be done in SiPass Entro Siemens Building Technologies will not warrant systems where other types of cable are used for these connections Cable types must not be mixed in the different cable segments From unit To unit Type of cable Maximum length m PC SR35i RS232 25m Cable between PC printer and segment controller Maximum length 25 meters Specified cable Straight screened cable 4 screen e g Belden 9534 SR35i Network Depends on the Cat 5 cable 10 100 Mbit Ifin Network structure but doubt consult the IT manager Normally 100 m to router switch hub SR35i SR35i RS485 1200 m The global circuit between the segment controllers Specified cable Pair twisted screened 1 pair screen e g Belden 9502 SR35i Network Depends on the Cat 5 cable 10 100 Mbit Ifin Network structure but doubt consult the IT manager Normally 100 m to router switch hub SR35i DC22 RS485 The local circuit 1200 m DC12 between a segment controller DC8
16. a 14 3 4 1 Enrolment reader KIL issiria a a A 18 3 5 Small applications without LAN cccccccceecceeeceseeeeecaeeeeseeeeeseeeeeseeeees 18 3 6 Larger applications with without LAN cccccceececseeeeseeceseeeeeseeeeesaeeeees 19 BS COMMUNICATION WIM PC esra a a 22 3 7 1 Local Area Network cccccccecccsececeeeeeeeesaeeeseeeeseeeeseeeeaeeesseeesaeeees 22 3 7 2 RO 2 OZ sicher eae ee ele a ee 23 3 7 3 TNO GC ised s a sede bactaseamascinacsatt vaee une peaseeeaeacuecsese sabes 23 3 8 Connect more than one PC ccccccsececeeceeeeeeeseeeesseeeeceeeeesesesseeeesegeeees 24 3 8 1 Multi user database aici21s5c2sawlat inet doc usin ici dees ae 24 3 8 2 Microsoft Terminal Server 2008 ccccccseececeeeeeeaeeeeseeeseneesenes 25 3 9 Global communication between several SR35i ccccccseececeeeeeeeeeeeeeeeees 25 3 9 1 ROA GO ata teamed eden dur ea a a 25 3 9 2 Ethernet with TCP IP i 3428 es wea eee ee 25 3 9 3 Example of SR35i with RS485 ce ccccececseeeeeeeeeeseeeesseeeeeees 26 3 9 4 Example of SR35i used in Local Area Networks 00s0eeeee 27 3 9 5 Example of SR35i using Internet cccceccceeseeeeeeeeeeeeeaeeeeeeneees 28 3 10 Wireless COMMUNICATION cccccccceececeeeeceeeseeeeaeeeeaeeeseeeeseueeseeesseeeseeesaeeess 29 9 11 TROSCIVALION Seu teeie rane eet etn esa a e eee ate 29 3 11 1 Integrated Web server cccceccccseseceseseecseseeceeees
17. address But can not directly be reached from outside the router 3 The routers must be setup with the correct port and IP address to the subnet agent 4 Administration PC 53 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Prepare any network resources 9 7 Apartment building example We assume that an apartment organization shall install a new SiPass Entro system in three different houses where we use three SR35is We now describe how the controllers are configured with DHCP and we use DynDNS because the ISP does not allow static IP addresses A laundry room also exists in one of the buildings where the SiPass Entro reservation system shall be used the tenants will use their home PC to make bookings and get confirmations The requirements for this are ALAN must exist in each building where SR35i is installed An Internet account must be available to allow for identities for the SR35is One SR35i must also have the CF8 flash memory installed for reservation functions The final system will have an administration PC installed The three controllers can be prepared in advance before mounting because they include a battery keeping the information database until the final installation is done Follow these steps 1 Sign up fora DynDNS account gt 52 with domain name dynalias net User name MyAccount and the password
18. and place the CF8 in the SR35i Controller 26 13 3 Example of confirmation Write e g the following text in the file reservation txt and store the file in the CF8 sbj lt Reservation confirmation gt Hello pfnm This 1S an automatic e mail message that confirms your reservation of Srobn Srhur rmin ehur emin on rdat rmon To change any reservation log on to ipme login html If the person s first name is Thomas and they have reserved the Tennis court 1 on the 14th of July at 2 4 PM the e mail message will look like this Subject Reservation confirmation Hello Thomas This 1S an automatic e mail message that confirms your reservation of Tennis court 1 14 00 16 00 on 14 06 To change any reservation log on to http XXX XXX XXX XXX login html In a similar way the file cancelreservation txt can be changed The table in the next section gives more types of information you can include 113 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 13 3 1 Table of e mail fields in reservation confirmations The table below shows different types of fields which can be included in e mail messages It is the text in the left column that may be included Field Function pfnm Persons first name plnm Persons last name pfrf Persons free field 1 normally email address pmno Persons
19. be included and chooses the relevant reservation time schedules The users wanting to reserve times can use an ordinary web browser such as Internet Explorer and login to the SR35i containing the reservation system Alternatively use his her card in a reservation terminal InfoPoint IP811 depending on how the system is configured 29 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 11 1 Integrated Web server The SR35i has an integrated embedded web server function which is used for reservation applications It requires that the dedicated SR35i have a permanent connection to the Internet when Internet is used i At least one of the SR35i must be equipped with a Memory card for web reservation which will contain the reservation information CF8 4 Example of standard solution for Reservation 1 Web browser 2 Gateway 3 Local Area Network 4 Memory card for web information web server 30 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 11 2 How the Reservation system is installed First all the doors and any IOR6 for doors and machine control in the objects are installed according to earlier sections Afterwards the CF8 is mounted i
20. be used a CF8 memory card must be installed in one of the SR35i segment controllers CF8 Memory card Reservation terminal An InfoPoint P811 can be used in a reservation system enabling reservation local to the object Includes an integrated card reader function for identification InfoPoint IP811 Cards Every person would use either a card or proximity tag Mil Modem If multiple SiPass Entro systems make up the installation a modem may be connected for communication between the systems and the central PC Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment Battery backup One or more battery backup power supplies are recommended for the system s power Cables USB RIF 2 used for enrolment and log on functions USB to Reader interface converter 17 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 4 1 Enrolment reader kit USB REF 2 USB RIF 2 to PC In SiPass Entro an enrolment reader can be connected directly to a PC via the reader interface USB RIF 2 It can be used for Login of cards Login to system software with card Fast search of card holders USB RIF 2 connects to a standard USB port in th
21. be used as a good alternative Instead of using each SR35i for this If the router is used for reporting a subagent SR35i must have the very same identity as the router Whenever the SiPass Entro will be using a DHCP server router for IP settings a function for dynamic DNS Dynamic Domain Name Service must be established The DynDNS functionality must be used to keep the identities intact for the SR35i controllers There are two options to report to a DynDNS service Use the router if possible to report Note that the identity chosen for the router must be the same entered in the SR35i Subagent identity See the router s handbook how to configure the DynDNS function in the router Use a SR35i to report In both cases the DynDNS service must be established 51 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Prepare any network resources 9 4 1 Configuring of DynDNS org 9 5 Firewall 52 Currently the instructions to configure an account with dyndns org are as below You can read more about this on their web site by browsing to www dyndns org www dynDNS com 1 2 Create a new account User name and Password If you have your own domain you select Custom DNS otherwise select Dynamic DNS These choices will later be referred to in SiPass Entro Choose among the available domain names If you chose dynalias net a SR35i will get the
22. booking is available E g 31 days Max value is 365 days Decide on how many minutes the system waits until an automatic cancel is done Enter in the field Automatic cancel time This gives a delay before some other Member group can book the same time Max value is 60 minutes Enter the allowed Overlap time for accessing the object after the reserved time This makes it possible to enter a booked tennis court some minutes later due to a traffic jam or similar Max value is 99 minutes Enter how long in hours and minutes must remain of an interval to allow for a new reservation Maximum value is 23 hours 45 minutes Click OK Repeat necessary steps for each reservation object 107 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 6 Enter public holidays and holiday periods in Reservation Certain day s reservations might not be available E g if tennis court is used for a tournament or if a golf court has closed for the season See also section Service mode gt 110 for another type of exception In the ordinary SiPass Entro system there are Public Holidays and Holiday periods which allow exceptions from an ordinary week These can also be used in the reservation system to inhibit reservation at these times In most cases they will not coincide and must be specified for each separate time schedule in the Reserv
23. communication secure in Entro All communication in SiPass Entro is heavily encrypted At the moment RSA RC4 128 bit is used This is the same level as most banks are using The encryption key can easily be changed In Internet applications the IT manager can raise the security by increasing the encryption set up in the LAN itself In addition the User name and Password is checked at login as well as the correct System name What is RSA RC4 RC4 is a symmetric encryption method developed by RSA Security which has been used for many years and is seen to be very reliable SiPass Entro uses 128 bit strong encryption When comparing encryption algorithms it is not correct to compare only the amount of bits because different encryption methods have different strength siPass Entro uses a symmetric method not to compare with e mail software usually using PGP or similar which is an asymmetric method with public keys These methods normally require a higher size of key to fulfill the security need What is MD5 MD5 is a method to confirm messages and logins This is used in SiPass Entro to ensure that all messages are correct when they arrive In addition also as an extra security when logging on via an web browser on to the Reservation system 123 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 FAQ 28 2 What redundancy is there in the system 124 The system i
24. family member group dnam Door name Yrwkd Weekday of reservation Start ryer Year of reservation Start rmon Month of reservation Start rdat Date of reservation Start rhur Hour of reservation Start rmin Minute of reservation Start robn Yewkd Reservation object name Weekday of reservation End eyer Year of reservation End emon Month of reservation End edat Date of reservation End ehur Hour of reservation End emin Minute of reservation End ipme IP address to web server me Note This parameter does not work in DHCP environments Please write the web address in plain text 26 13 3 2 Special e mail fields The following fields can also be included if other people need a copy of the e mailed confirmation sbj lt x gt Mail subject x Subject text bce lt y gt BCC recipient y e mail address for secret copy rcee lt z gt CC recipient z e mail address for copy 114 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Maintenance 2 Maintenance 2 1 Expanding and modifying the system Expansion and modification of a SiPass Entro system can of course be performed in many ways Sometimes more doors are needed sometimes also requiring more SR35i controllers or mor
25. finding addressed and connected segment controllers and door centrals Subsequent expansions with additional units will also be found in then same way If the site is correctly installed with appropriate addresses you only need to step through each SR35i and door centrals A list of units will be displayed on the screen as soon as login to Installer is done A SR35i is displayed as Cxx and a door unit or IOR6 is displayed as Cxx Dyy 57 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing the software 10 2 Multi user environment more PCs If only one computer will be used no special arrangements are needed A connection has been created automatically by the installation wizard In cases where several computers shall be connected the software must be setup for using more than one connection Every PC used in network applications should be linked connected to the same SR35i This is especially important if a SR35i is used as a subnet agent Any controller that is managed by this subnet agent cannot be linked to any PC Proceed like this gt Every PC must have a valid SiPass Entro software license 1 Go to the Connection tab in the System System settings and select that several computers can be connected concurrently 2 Click OK and a new tab appears in the main window in the Installer The default earlier hidden connection is now di
26. frame How often does the SR35i communicate with each other At least every 6 8 second How often the SR35i does requests a timeserver It does it every 23rd hour continuously What happens if the SR35i loses the database and uploads from another SR35i does the LAN become slow No because we only use a fraction of the total capacity SiPass Entro uses 10 100 Mbit LAN and just a few percent of that The reason is that the SiPass Entro primary should handle the access issues rapid The communication has a lower task priority In addition the communication is encrypted with 128 bit RC4 which together with the MD5 authentication takes CPU power and reduces the speed However in modern LANs switches are often used which not affect the speed negative Is it possible to change the IP port used by the system e g if 4001 and 4002 are occupied by another application Only port 4002 is used in communication to the PC and may be in conflict with other application is the same PC You cannot change the port The risk for a conflict is seen as minimal If this should be a problem we will of course solve it There are no applications known so far that uses this port How is the traffic affected Use of sniffers We have during the development phase off course have been using sniffers three commercial and one of our own We have also bursted 100 bandwidth to Building Technologies Fire Safety amp Security Products
27. intact but an interruption occurs e g the data memory is corrupt the data is recovered automatically trough an up or download The stop of communication will generate an internal alarm to connected PC and or an external alarm via IOR6 What happens if a SR35i fails Due the SR35i s isolation capabilities the superior global communication will probably still work If the door environment still has power and includes a DC22 DC12 with memory these will pass to an autonomic mode where decisions of access are taken locally Other doors without DC22 DC12 can be locked or unlocked When the faulty SR35i is replaced it will automatically recover itself via a download from an other SR35i or PC The event alarm functions still apply What happens if a reader or door controller fails In most cases other doors controlled by the same SR35i will still work An alarm event will be sent from the actual SR35i if the door controller communication fails When a reader fails this will be indicated in the System information window What happens during a cable failure A stop in the global communication between SR35i Segment Controllers will be discovered and an alarm event is sent from every SR35i respectively The doors can work as normal A stop in the local communication between a SR35i and door will be discovered by the actual SR35i and an alarm event is sent from actual SR35i The doors goes offline and some doors may also grant access de
28. network identity Identity1 dynalias net It will be easier if you already have a list of network identities for all SR35i available Note that this is not the same as the name of the controllers as shown in an event log Carry on entering the identities for the remaining SR35i that will use DynDNS Remember that when a subagent SR35i is used for managing other SR35i behind a router only the subagent needs to have an identity But then exactly the same identity as the router In systems where a firewall is used and there exist external SiPass Entro equipment some actions will be needed Depending on the application some ports and IP addresses have to be opened Consult the IT manager Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Prepare any network resources 9 6 Example with router In most cases the access control system is installed in local area network LAN where both dynamic IP addresses and subnets are used The diagram shows an example using internet SR35i Internet solution with routers 1 SR35i acting as a subnet agent This SR35i will get a dedicated fixed IP address and is ported in the router item 3 The subnet agent manages the communication to any of the other SR35i items 2 on the same subnet 2 SR35i that resides inside subnet and have a dynamic IP
29. the COMMUNICATION CIPCUITS cccccccccececececccccececcccueaeaeuenenenenecenenes 14 14 2 Check the power SUPDIY ccccsecccceececceececeeeceseeceseeseessaseesaaeeeseeesseneesens 74 15 Ea Ee a a ae E en a ne ae ae ene E AT 75 16 Start the SOMW alre wise ane e a a i e 76 16 1 Indicators for COMMUNICATION StatUS ccc cece ec ecaececececeececececeeaececececeeaeaees TT 17 Settime and dat orca a aa a ai 79 18 Advanced system clock management cccccsccecsseeseeeeeseneeseneesenensnees 80 19 Personalize Entro settings sssssssnnnsnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnne 81 19 1 Card reader paraMeters ccccccsecccceececceececeecesseecesseseeseaeeesaaeeeseeesseeeeseas 81 19 2 Personal code without Card icine Nioed iaien edie ae ee Aes 81 19 3 Changing red LED function ON readers cccceecccccseeeeeceeeeeeeeeeesaeeeeesaeeeees 82 19 4 Duress code ON OFF 2 2 20 cc cc ccccccecececcceccccceceneceneneneueceneaeaeaenenenenenenenenenenenenenenes 82 20 Configure names for segment Controllers ccccceceeeeseeeeeeeeeeeeeneeeeees 83 20 1 Create multiple SR35i for TCP IP Communication cccecceeeeeeeeeeeeeees 83 20 2 Create multiple SR35i for combined TCP IP amp RS485 communication 84 20 3 Create multiple SR35i for only RS485 communication ccccccceeeeeeees 85 21 SRS C OMMGUFING s sa aaa aa aa aaa daaa aa aaan 86 21 1 Decide on networ
30. the drive gt The wizard for updating software is visible Follow the instructions on the screen Choose Repair 4 Open the Installer gt 76 application The installation checks the existing software version and will warn about any possible necessary hardware change as above It may give the option to update some units directly where some may be mandatory for the overall upgrade This step is similar to SR35i Firmware control gt 120 5 Perform the suggested steps in sequence 6 Check that the indicators ONLINE and DB UP TO DATE in the lower right corner of the SiPass Entro windows display is green 116 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Maintenance gt The SiPass Entro system is now updated to a new version and is ready to perform new tasks 27 5 Installing an additional or replacing a PC SiPass Entro version 5 3 onwards allows that several PCs concurrently can administrate the system If only one PC is used the tab Connection is not displayed in the Installer application If several PCs will be on line concurrently the tab Connections displays the different names Before you begin Regardless of which above the new PC must fulfill certain requirements A separate SiPass Entro software license must be available for this PC The SiPass Entro program should be installed on a PC with its own valid net
31. with the SiPass Entro software to one of the segment controllers to be able to configure the system see the next section Configuring the modem based system on site gt 60 When the configuring is finished you can disconnect the PC and connect the modem instead Do not forget to test the communications gt 74 circuit and the power supply gt 74 11 3 Configuring the modem based system on site 60 Configuring the new system should be done on location i e with the PC connected with RS232 to a segment controller in the new system 1 Open the Installer gt 76 application 2 Click the tab New connection and you start a wizard to establish the connection between the PC and the controller No login is needed because the system database is probably new and will use the default user name bewa and password pass 3 Select New system and proceed Select RS232 and proceed gt The software automatically detects the correct COM port 5 Enter a name for the new system in the Site name field e g Oak lane gt This name will be displayed in the SiPass Entro Login windows for the user to choose whichever system he or she wants to work with 6 Enter the system s name in the System name field This name must be unique and identical with the name you will be asked to enter when setting up the main computer see Transferring the new system s information to the central PC gt 63 It is very important that you make no
32. 00 and its subordinate door readers door controllers Pair lOR6 twisted screened 1 pair PD30 EM screen e g Belden 9502 or PD40 EM Cat 5 communication and 1 5mm power OR PAARFLEX CY custom cable comprising communication and power in one cable DC22 BC43 BC Link 100 m DC12 M43 Specified cable Straight DC800 PR500 screened cable 4 screen HD500 e g Belden 9534 SP500 35 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 System requirements 4 2 Cables From unit To unit Type of cable Maximum length m PM500 PP500 HF 500 Clock amp Data 50 m BC5511 Specified cable Straight screened cable 6 screen e g Belden 9536 Wiegand Wiegand 50 m readers Specified cable Straight screened cable 6 screen e g Belden 9536 SiPass Entro can be operated using different cable types for the communication levels as well as for the power supply 4 2 1 Cable for power supply In both large and small systems it is important to use the dimensioned cable correctly The most important factor to consider is that the cable is linked to the door environment In most cases it will be the electrical locks that will consume the most current and could cause a drop in voltage This is why it is necessary to know the types of locks lock strikes motor locks etc when dimensioning the cables In most acce
33. 8 When displayed an application called Entroser SiPass Entro serial communication is running in the background This is a required condition for events to be displayed on the PC s screen and or stored on hard disk Entroser will be running even if you exit any SiPass Entro application Despite the name Entroser this is also used in TCP IP communication Close application and stop communication In some cases a complete shut down of the SiPass Entro is required E g during maintenance actions like updates or similar Proceed like this 1 Position the cursor over the icons and right click gt A menu is displayed 2 Select Close Entro gt All communication entroser is stopped and the current database is stored The icons disappear from the task bar No events will be stored For Windows 7 to see the notification icon right click in the notification area and select Customize notification icons Find the entry for Entro and choose to Show icon and notifications in the drop down list Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_A24205 A335 B317_e_en 10 03 2010 Set time and date 17 Settime and date Before starting to configure you should set the correct time and date The clock is shown separately in the lower right corner of the window Note that if any SR35i is set to TCP IP and will get the time from an external SNTP timeserver you cannot manually set the clock See se
34. ACE MS ccccsecccesececeseccseseeceseeceeseecesueessaeeeseueeeseueeenages 119 21 8 SR 35i firmware Controleren ananena iinei e aa 120 27 9 Saving restoring database on CF8 ssnnnnnennnesnnnesennnesrrrrenrnnsrnnenenrnesnnnee 120 27 10 Door controller firmware control cccccccseeeeeeeeeeeeseeeeeesaeeeeeseeeesaeeeeeesaess 121 27 11 Printout of system CONFIQUIATION ccccceecceeeeeeeeeeeeeeeecaeeeeesaeeeeeeseaeeeseaees 121 27 12 Migrating from a Entro Lite system cceccccceeeeeeeseeeeeeeeeeeesaeeeeeeaeeeeeseaees 121 2113 IISA ENI Onia a a nen 121 28 PAQ e aa a a a aE 122 28 1 Advanced information about LAN cccecccccseeeeeeeeeeeeeaeeeeeseeeeeeaeeeeeseaees 122 28 2 What redundancy is there in the system cccccseeececseeeeeseeeeeeeseeeeeeeeees 124 29 Important information fOrM s sssssssennnsnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnn ennnen 126 BO NAEK ap E aa 127 7 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 About this document 1 About this document 8 This document contains information on the installation of the product Other related documents are SiPass Entro Project design manual which describes important concepts SiPass Entro User manual which describes the operation of the software For the installation of the hardware components please refer to the hardware manuals of the
35. Edit Click the tab IOR6 Inputs Select Exit button if not selected already Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_A24205 A335 B317_e_en 10 03 2010 Configure IOR6 relay controller 23 Configure IOR6 for Reservation system If any of the relays in an IOR6 are going to be used in a Reservation system follow these instructions 1 Open the Installer gt 76 application 2 Click the Door tab Normally a new IOR6 is displayed as Cx Dy in the list of doors Mark this click Edit and step to item 7 below If you manually want to create a new IOR6 proceed as follows Click New The Door properties are displayed Enter the name of the relay controller in the Name field Check and or enter the address In the list box Terminal type select IOR6 Click the IOR6 Relays tab Mark the tick box Reservation door and or Reservation machine 2 ot 0 Ok oS Oe Enter the name of each relay with digits They will later be shown as the name of the IOR6 the relay number E g if the IOR6 is named Washing room and relay 3 it is shown as Washing room 3 10 Click on the list box on each relay and activate them as follows Reservation Door Means it will be used as an ordinary door opening relay and is activated for a specified opening time Reservation Machine Means that this relay is activated the who e time the object is booked e g a washing machine Note if any
36. Installer application when creating connections and camera settings 13 7 3 CX Live Viewer software The software for remote viewing currently named SX CX Client on the DVR must be installed in the actual PC where SiPass Entro is installed Otherwise no view will be displayed 13 7 4 Additional considerations for the CX The IVM rules standard have to be activated to get the pre and post recording functionality in the DVR to work 73 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Before configuring the system 14 Before configuring the system Before commissioning the SiPass Entro system the installer should read and complete the checklist gt 75 14 1 Check the communication circuits Go to all units in the system and check that they are communicating When all units are connected but with all removable terminal blocks disconnected in drop boxes and door controllers check on reader block nos 3 and 4 in drop boxes door controllers and segment controllers that the resistance on the global and the local communication circuit respectively is 60 Q ohm plus the cable resistance Ifthe resistance is 120 Q plus the cable resistance one termination resistor is missing If the resistance is much less than 60 Q there is a short circuit in the communications circuit Ifthe resistance is much greater than 120 Q open circuit there is a break i
37. MyPassword 2 Apply these settings to the SR35i SR35i Name in log Network ID 1 Controller House 1 house1 dynalias net 2 Controller House 2 house2 dynalias net 3 Controller House 3 house3 dynalias net 1 Install the software gt 55 in the PC Enter House1 dyndns net as network ID for the first controller that the PC will use for communication 2 Select the alternative to report to DynDNS org and enter the Account type Dynamic DNS User name MyAccount and password MyPassword and exit Configure all SR35i manually with the New button and enter name etc 4 Proceed with the tab Network and mark the tick box Obtain an IP address automatically also the DNS address can then be allotted 5 Enter the Identity according to the above table e House1 dynalias net etc Simultaneously you enter the name of the ISPs e mail server e g mail1 telia com to prepare the controller to send confirmations 6 Set up all SR35i in the same way 54 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing the software 10 Installing the software After the software installation from CD you shall open the Installer application If the system will use dynamic IP addressing technique DHCP on the local area network you should prepare the network gt 49 resources before installing Normally the installation automatically starts when
38. NOCUON rricesr cage teens es a a a ea ca nee ee ed 66 FIOW to contol recordings aertiro a A 67 Camera SetinGS airsan Sa 67 SD TORE NIND aeaa ao te EER 68 133A MX Parameter S ice ss a a Mewes e a e S 69 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_A24205 A335 B317_e_en 10 03 2010 13 5 2 MX Live Viewer software cccccccccccececececececececececececucecucececeneces 69 13 5 3 Additional considerations for the MX c cccccccecececeecececececeeeeees 69 Tg SVS ORR Kereta saad ets ert nat Mac ae hasan ac E AE 70 10t GCN CWA tc feo de sed adetesie a seca Sicdstonsaddca eee iva cca edness 70 W362 SAO AKG irate srtt pales cecialsdatadiosaccidulsidendiatareteiacaccsdelanctaianaecte 70 OS SAKAAROAK EITC a NE 70 BOA AX Farane Siaa aa a aa aa 11 13 6 5 Additional considerations for the AX cccccccececececeececececeeeeceees 72 13 6 6 AX Live Viewer software cccccccccecececccccccecececececececscucecececeneces 72 SR NS Re es cca arc ea seat ncaa E ict baa E E N E E eek 72 Ort GON CWA act ies cecil A a boss eb a edo ee es 72 Ior OFT AVAIMIC OTS wig state TA N tte 13 13 7 3 CX Live Viewer Softwar e c ccccececececececccecccecececececaueuauauaeaeaees 73 13 7 4 Additional considerations for the CX ccccccccccececececececeeeeaeeeees 73 14 Before configuring the system c ccscseesssseeeesseseeseeseeeseeeneesseenseeseaneeees 74 14 1 Check
39. P addresses Static P addresses can exist in both local area networks and or where also the Internet is used e g for reservation functions Some ISP unfortunately do not allow for using static IP addresses In a local area network environment the only aspect is how isolated the security system should be compared to an office network e if any routers firewalls or similar software are separating the SiPass Entro from any other network equipment Dynamic P addresses In earlier versions of the SiPass Entro software the segment controllers was supposed to be addressed with a static IP address which is still the preferred method as long as the local area network LAN allows for this Think of a having the same telephone number all the time Static P addresses are both faster and more secure In some facilities only one Internet Service Provider ISP is contracted offering only accounts and connections using DHCP Dynamic Host Configuration Protocol This means that the host environment at the ISP lease out an IP address for a short time therefore the IP address can be changed when the ISP renews the lease time As IP addresses are not static there must be a function that refers to a fixed name which can be translated to a concept the Internet can still understand i e IP addresses This function is generally called DNS Domain Name Service and can be seen as a name directory with IP addresses T
40. PC which sends a request when starting the Installer program If a SR35i is found you can add it and configure it like the other controllers If the conditions for the above are not met proceed as follows 1 2 Select an address for the new SR35i and power it up Set up the networking parameters e g IP address using the keypad and display Eventually you must erase the memory of the SR35i If the Crypto key has been changed before in the system it should be temporary set back to default same as the SR35i factory setting Otherwise the controller will not communicate Go to Entro program and Change Crypto key in System menu Connect the network cable and start Installer gt The new controller will be found by the software and is shown as Cxx The database and the crypto key are sent or verified from the PC to the controller Note that firewalls etc may require that some SR35i have to be setup manually no Cxx displayed Change name and set up the parameters for this controller Wait for an updated database icons are green Do not forget to change the Crypto key and note it down 2 f Installing more readers It is very easy to install more readers in the system You only need the necessary cabling and ensure the following A free DC 12 or DC22 are available for the reader Does not apply for the PD30 EM PD40 EM That the hosting SR35i does have enough addressing capacity That the power supply h
41. Pass Entro environment because otherwise it is a risk that the on screen name differs from the name seen in the SiPass Entro event log When the parameters are configured enter them into the SiPass Entro Installer application when creating connections and cameras 13 5 2 MX Live Viewer software If you only want to do the basic viewing from SiPass Entro just install the RemoteView module on the actual PC where SiPass Entro is installed Otherwise no view will be displayed 13 5 3 Additional considerations for the MX Following settings must be performed in the MX Inthe configuration software trigger has to be activated to start recording You have to activate that at the MX itself It s not possible with the remote configuration Continuous recording has to be activated This can also only be activated at the MX itself 69 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Install DVRs 13 6 SISTORE AX 13 6 1 General When integration the range of SISTORE AX DVR s in SiPass Entro there are a couple of settings that has to be correct in the DVR in order for getting a correct functionality 13 6 2 AX9 and AX16 Continuous recording setting in SiPass Entro causes problem from event recording and is recommended to not be used Note that if you connect a VGA monitor to display the on screen menus and images check that the rear selector
42. R500 for example The ENTRY PR500 and the link for EXIT PR500 are controlled internally by the door controller that decides upon the direction Wiring the door monitor contact and lock are done as usual wp a BCLINK EXIT reader ENTRY reader Door monitor contact Pe Electric lock Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Special installations 6 2 Anti pass back using Clock amp Data and Wiegand readers If the readers do not support sub addressing the door monitor contacts and opening relays are connected as follows AOH ENTRY into the zone EXIT out of the zone Power supply Opening relay Lock Remote opening Door contact Opening relay Note Voltage free contacts pp pS OF ee a Reader Only connect the door contact on the ENTRY reader Connect the EXIT reader s opening relay with voltage free contacts to the ENTRY reader s remote opening input If needed enable event registration of Valid access Exit button in SiPass Entro event filter settings i Note that only the ENTRY door controller monitors that the door is physically opened The EXIT door controller registers the granted access from the zone but cannot monitor the door opening If this is required we recommend that an
43. SIEMENS SiPass Entro Installation MP6 5 SP1 Building Technologies Fire Safety amp Security Products Technical specifications and availability subject to change without notice 2010 Copyright Siemens Switzerland Ltd We reserve all rights in this document and in the subject thereof By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part nor to make them available to any third party without our prior express written authorization nor to use it for any purpose other than for which it was delivered to him Table of contents 1 ADOUL this document siccdectsiiensiiotie enter tienen ination tiie 8 2 Sale esdtwesvescuere vena escusatectaieaces sauce tabuadccussnuncatt czauncaducuaun seieccuestectamesconenvextucavee 9 ZW PARQ CTOR OUD 22 so seuss cece nc ca N a A acauece 9 3 Description Of EQUIPMENEL cccceceseeeeeeeeeeeeeeeesaseeesaneeseeseeseaneeseanesseeenes 10 3 1 Software CESCMDUOM wiccetscrusetect cbesctatersedethcsapndeteateddadeesaad tes ileditaaedetbetuctatends 10 3 1 1 Software Applications cccccseecccsecccceeeeceeecceececseeeeseeeeeseeeesseees 10 3 1 2 SOMWALE WIKOWS cicscoastccich anaia sanaaa a a a aia aae 11 32 System OVEMIEW sccai eee eae eee eae eed 12 33 System capacity and NIMES urcicin Wrrce contest ance encadoantin a Gceatua amends 13 34 System COMPONEINS casen aa ven asana a a AS iaa
44. System gt System settings menu and decide on the general names for classes one two and three This will then be visible in each object for further defining of values Open the Entro gt 76 application Click the tab Zones gt The previously defined objects are displayed Mark the object and click Edit Select the Time schedules from the list Click on the arrow to list available time schedules You can also click on the clock icon to Create Edit or Copy a reservation time schedule Then choose the desired time schedule by clicking the name Mark if flexible reservation within an interval should be possible Read more in the Flexible reservation in same interval section Enter how many Maximum no of concurrent reservations on the same object will be allowed E g if a tennis park has two separate courts but only one door two different member groups must still be able to book the same time Max value is 99 Click the tab Max nr limits Decide on the users reservation capabilities for a certain advance period E g to book four training sessions in a month in the same object Max value is 60 on each Choose if even more restrictions should apply for each class Enter in the field Max nr and Calendar period the number of reservations maximum 6 a member group can make in a certain period day week or month Click the Time related restrictions tab Enter in the field Max forward reservation time for how long a period
45. a System name The crypto key user name and password are known at this stage Existing There is an installed SiPass Entro to connect The system name crypto key must be known as well as the user name and password that system 55 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing the software 4 By default the wizard searches on the local area network and the serial port for any connected SR35i and displays a list of segment controllers found Also controllers connected to a COM port in the PC will be found SiPass Entra Select controller to connect to These ane the coriroders that have been Found on TOP SIP that wou can connect bo Or Press Oihe F the one you want to commect to E not ited here Ib IP Address i 10120 ii 10 1200 Bie To change the IP address of 10 1 200 Boe An SRW select Ein the et and cick on Edt IP address 2 3 5 From the list you select the SR35i you intend to use for connecting to this PC Note only one can be used 6 Finish Manually decide on SR35i If the correct SR35i is NOT found in the list this indicates that the intended controller is located outside the local network and its IP address has to be configured manually The network gt 49 must also be configured correctly to get the PC online 1 Select how this PC should communicate with the site TCP IP RS232 or modem If you se
46. alled the modem If the PC has to be replaced you must enter the same system name once again Exit gt The wizard will now try to connect dial up the remote site If this fails proceed as below The SiPass Entro Installer main window is displayed The name of the chosen system is displayed in the window s title bar Since you have not yet called the new system you are OFF LINE Click the lifted handset symbol on the tool bar or choose Call on the Modem menu A message is displayed while the system tries to establish a connection When the connection is established the systems are in direct contact i e the green ON LINE gt 77 indicator is lit When all information is transferred this may take a couple of minutes the DB UP TO DATE gt 77 indicator will also turn green The new system is now ready to receive information about time schedules persons access groups and doors i SiPass Entro should always be ONLINE connected via modem when configuring a modem controlled system This way information transfer will be quicker and safer 63 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing the CF8 flash memory card 12 Installing the CF8 flash memory card 64 The CF8 memory acts similar to a hard disk unit for storing files When delivered it contains the HTML files used in the Reservation system 1 Remove the power from the actua
47. alternative to RS232 where longer distance lt 100 m is required Directly connected with LAN In this example the integrated network switch is also used to connect the PC onto the LAN 1 Integrated network switch 2 RJ45 type of cables Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment Local area network with InfoPoint IP811 The InfoPoint can be connected directly to the SR35i segment controller InfoPoint IP41 Hs _ as p Law 3 7 2 RS232 SR35i communicates with the PC via cable directly to the COM port SR35i 3 7 3 Modem The PC is used to control a remote site using a dial up modem The SR35i is also connected to a modem which also can dial up the PC if necessary SR35i 23 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 8 Connect more than one PC 3 8 1 Multi user database Every SiPass Entro system uses a database with cards time schedules etc which is stored in every segment controller and PC The SiPass Entro database allows for multiple users to be working with the same database The prerequisites for this are that the system knows which Users are using which computer E g a Security manager can have their own PC with a dedicated license while a Rec
48. are versions etc Proceed like this 1 2 3 Open Installer gt 76 application Choose System gt System information Click on Save as as an image in JPG format is stored on disk 2 12 Migrating from a Entro Lite system When migrating from a SiPass Entro Lite system there are some considerations must be taken The database used in SiPass Entro Lite allow for card holder names up to 50 character When an import is done to SiPass Entro only the 32 first is imported If the Duress function is used in the DC800 controller this must be moved to an IOR6 relay gt 93 controller and the SiPass Entro configured for that This applies even if the DC800 still is used as a door controller in the new system Also if the Alarm bypass function is used considerations must be taken to redesign the solution 2 13 Uninstalling Entro To uninstall the SiPass Entro use the Windows system There is no special menu choice for uninstalling After uninstall the following files are kept for future references If a complete removal is desired proceed as follows 1 Go to the Windows users profile folder Example for Win XP C documents and settings Username Remove all SiPass Entro files under Application data dbpath ini entro ini database and event files Go to C Program files Common files Delete the complete folder Bewator USB 121 Building Technologies Fire Safety amp Security Produ
49. arm time schedule automatic Using the door icons in the Door and Event Monitor program right click Use the intrusion alarm maneuver functions The alarm panel status signal is used to follow the status of the intrusion alarm controller feedback To disarm the alarm following methods are valid Using a valid card at the door terminal Using the door icons in the Door Monitor application right click Use the intrusion alarm manoeuver functions The alarm panel status signal is connected to the ASF input NOTE 1 Remember that any zones e g Alarm zones will work best if they reside in the same sub net when several SR35i use TCP IP between related SR35i NOTE 2 Remember that any DC22s configured for Monostable alarm cannot be wired for controlling any zone in the intrusion alarm In cases where only one door is used to control an intrusion alarm you must still create an alarm by pass zone for that door Note that an alarm by pass zone can be combined with both roll call and entrance limitation but not with anti pass back 1 Open the Installer gt 76 application 2 Click the Zones tab then New For new zones a wizard is invoked which will help you configure the required functions For existing zones the tabs are shown displaying the same information Tip You can also right click and choose New Edit or Delete Type the name of the zone in the Name field 4 Select Alarm zone You wil
50. as a valid e mail address entered in the free field of the person s properties in the Entro application 9 If you have named the SR35i Reservation and enter xyz com as domain name the message is sent from the sender address reservation xyz com to the e mail address entered in the first free field on each person s properties 112 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 13 2 Editing text in the confirmations The actual texts sent are stored in files CF8 memory card and are named reservation txt Message sent when reserving cancelreservation txt Message sent when canceling To change these you make use of a suitable PC adapter for retrieving and storing the contents of the CF8 memory card As follows 1 Place the CF8 in the adapter Be careful when connecting the card to avoid destroying the data Use the Windows Explorer or similar to find the files 2 Inthe folder LANG there are a number of language folders 0 1 2 etc Locate the file to change 3 Edit the file and write the text you want to display to the user You then include some optional field tags gt 114 that at run time will get information from the system like object date time etc If you include e g the tag pfnm the first name of the person will be displayed See further in section 4 Store the edited files
51. as enough capacity That the RS485 bus termination resistors are installed properly 119 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Maintenance 2 8 SR35i firmware control Sometimes when a system is expanded or upgraded there maybe need for patching the firmware in the segment controllers As soon as the Installer program is on line with the system it checks and inform the user about any updating needed In the Installer program there are functions for controlling the mechanism of patching the segment controllers The status of the different units is displayed You can also see the estimated time This applies for all controllers not only the one connected to the PC i The download is using the current files stored in the Entro program folder File type SR_firmware hex stored in the Entro program folder It is possible to download an old version Proceed like this for the actions you want to do 1 Open Installer gt 76 application 2 Choose System gt System information gt All controllers are listed on the screen showing the status for the different units address product version voltage level If any controller fails to communicate there is a cross over the unit Click on Update firmware and select which version to download Click on Next and mark the controller to be updated We strongly recommend that only one contr
52. ates resolutions and the size of hard disks that are available in the DVRs before configuring any triggered or continuous recording commands in the application Otherwise there might be a risk for data loss when the recording memory ends DVR Viewer You should also have installed the Viewer software that fits the actual DVR models Several can exist concurrently in the PC Obviously if not installed the SiPass Entro can not display any images from the particular DVR in use The SiPass Entro will notify the User to install the software Normally the Viewer software is supplied with the DVR If not contact your SISTORE supplier 65 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Install DVRs Clock synchronizing Both SiPass Entro and the DVR have their own calendar clock functions These should be synchronized to guarantee that events and images get the same time stamp The best solution is to let both systems update their clock from the same source usually an NTP server Also the SR35i can act as a server for the different SISTORE recording systems The SR35i Segment Controller can be setup according to this See the section Advanced system clock management gt 80 The DVR is setup according to its handbook 13 2 DVR connection When the SISTORE DVR is installed and configured some parameters in SiPass Entro software must be c
53. ation To make the system understand that holidays and holiday periods should not be treated as ordinary working days this information must be configured Proceed as follows 1 Open the Entro gt 76 application 2 Click Time Schedules tab 3 Select the time schedule click Edit and then the Public Holidays tab 4 Mark the tick in the Use Global Public holidays if you prefer to use the same dates as specified in the main Entro program Click New The Public holidays window is displayed In the Date field enter the date of the first holiday or click the Calendar button and choose the date You can have up to 14 days in each time schedule 7 Click OK The Public holidays tab is redisplayed with the date filled in 8 Click New and configure the next holiday accordingly Create the Holidays in the same way but enter both Start and End date You can have up to 4 periods in each time schedule 10 Repeat steps 4 8 for every separate time schedule in the reservation system 26 7 Decide on reservation authorities for access groups 1 Open the Entro gt 76 application 2 Click on the tab Access groups 3 Create or select an access group 4 Go to the tab Reservation objects If you also select the tick box Caretaker this group will be able to access and use this object 24 hours a day without any reservation Normally you create a separate access group with this functionality Select one or m
54. be valid for one door reader all other doors in the object will then be blocked for this selection Reservation time This may be a door on the way to the object and no time shift is added Time shift This door or IOR6 relay will allow for access only during a time shift Specified below E g time shift set to 30 min will result in access 18 30 19 30 Remember that doors relays of this type can only belong to one object Combined time This is a door that will allow for access the time for the Main door plus the time shift E g 18 00 19 30 Enter the time shift delay maximum 120 minutes if any door is using time shifts Click OK Repeat for any other new reservation objects to configure If any relay controller OR6 are used in the reservation object you configure these according to the section Configure IOR6 for Reservation system gt 95 Supplementary parameters for reservation are configured in the Zone tab of the Entro program 104 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Contigure for reservation 26 2 Random allocation or NOT of similar reservation objects If several similar objects are to be available for reservation you can randomly allocate them to minimize the wear on individual equipment If choosing to use random mark the tick box Random and read more in the section Reservation object group
55. cation will then allow for client PC to logon to the SiPass Entro programs More than one client can then be logged on concurrently and SiPass Entro manages all the database handling A license number is required for each client All events and information are stored centrally on the server and no data is stored locally Please refer to the special SiPass Entro 7erminal Server 2008 Installation Note supplied with the SiPass Entro package for installation and configuring 3 9 Global communication between several SR35i The global communication between several controllers can be done through two separate physical cables twisted pair RS485 and or Ethernet 10 100 Mbit 3 9 1 RS485 Use RS485 to communicate between a maximum of 16 SR35i controllers Maximum distance is 1200 meters from the first SR35i to the last one It is possible for one or more of these SR35i to use TCP IP as described below The controllers are then configured with an IP address and proxy function with SNTP 3 9 2 Ethernet with TCP IP Generally known as TCP IP that uses the Ethernet connection 10 100 Mbit that connects to the Local Area Network TCP involves a controlled way of sending messages through a network The maximum distance depends on the structure of the network itself Requires that the SR35i is configured with its unique IP address and having the Proxy function with SNTP This ensures that only the relevant units SR35i or PC receive the messag
56. components Note if you have been using earlier versions of SiPass Entro documentation you will now find information about some software configuring details in this Installation manual instead of the User manual Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 2 Safety 2 1 Target group Safety Target readers Qualification Activity Condition of the product Installer Technical training for electrical installations Installs the product individual components of the product or replacement parts Components of the product are not yet installed or need to be replaced or modified Operational start up personnel Technical training for electrical installations Training on the product is recommended Puts the product into operation for the first time or changes the existing configuration The product is installed but not yet configured or the existing configuration is to be changed Service personnel Technical training for electrical installations Checks the product at regular intervals to ensure that it is in good working order and performs service work Product already in use and requiring servicing 9 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment 3 Descriptio
57. controller automatically gets an IP address and a general DNS used for later search of IP address to DynDNS org Proceed as follows 1 2 3 4 Open the Installer gt 76 application Select a SR35i in the tab Controllers Click Edit or double click the name Go to the Network tab and mark the tick box Obtain an IP address automatically Enter in the field Identity the name for the controller If DynDNS is used it might be e g House1 dyndns net Identity1 dynalias net or similar If the controller also is used for confirmations in a reservation system enter the name of the e mail server This is obtained from the ISP E g mail1 xyz com Be sure the mail server allows for the chosen identities no blocking Decide whether the controller must report its identity to a DynDNS server By default it is assumed that this is supported by a router and the provider parameter will be set to inactive in the SR35i Note that if the SR35i is used as a subagent behind a router that reports to DynDNS the identity of the router must be entered as the identity of the subagent If you mark the tick box to report a warning may appear to instruct that a DynDNS account gt 89 must exist Click OK Repeat the steps for each SR35i using DHCP 87 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 SR35i Configuring The screen shot below shows the ab
58. ction Advanced system clock management gt 80 Proceed as follows if the system lets you correct the system clock 1 Check that the indicators in the lower right corner of the windows SiPass Entro display ONLINE and DB UP TO DATE Open the Installer or Entro gt 76 application Choose in the menu System gt Entro system clock Check that the correct date and time are displayed If not enter the current date and time in the New date and New time fields To disable automatic daylight saving time changes remove the tick next to the Automatically adjust clock for daylight saving changes prompt Click OK 79 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Advanced system clock management 18 Advanced system clock management You only have to make the steps below if you intend to let the SiPass Entro fetch its time externally and additionally allow each SR35i to adjust its time relatively to GMT siPass Entro uses a Simple Network Time Protocol SNTP which fetches an international clock GMT from an external SNTP process running on an external server on the LAN Internet or an internal server SR35i SNTP is necessary for SR35i s that are network connected TCP IP If in doubt consult the IT manager If any network is used the SR35i must be able to get the clock from a clock server when TCP IP is used Every controller set to Prox
59. cts 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 FAQ 28 FAQ 28 1 Advanced information about LAN 122 The following chapter contains questions and answers regarding SiPass Entro when used in local area networks and is primarily aimed at IT managers What does the traffic load look like when it is using Entro in TCP IP LAN As SiPass Entro TCP is evolved with RS485 the traffic is relatively moderate providing that the database is hard packed The traffic SR35i will have a socket open to every other SR35i This socket is alive and is tested for failures with a special ping message every eight second This is not an ICMP ping rather a common TCP IP package with some information only a few bytes in size Beside this in an idling system there is a comparing of databases message to the node nearby approx every ninth second The time depends of the configuration In a small system this could be every sixth second Also this message is short approx 40 bytes plus the length of header see item 2 How do the messages look like e g for events and creating cardholders What is size of packages is sent The packet size is currently 407 bytes plus TCP header and IP header together with a MD5 hashing of the message Totally it is less than 500 bytes The information sent in case of an event e g granted access is approx 40 bytes Creating a new cardholder results in a database update with a frame of 80 bytes and a 10 byte
60. d click on Edit O eT So ep Click on Entrance limitation and select restriction type both types can be selected Decrement entries counter Means that a certain number of entries are granted in doors included in this zone Later in the Entro application one or more access groups should be created with restricted access to these doors Finally the number of granted entries can be specified for each person Limited access to this zone e g twice a day If this alternative is selected go to the Settings of limited access box and select the desired time restriction e g twice a day If needed access can be limited further by choosing restrictions per time interval lf more than one entrance limitation zone is created only one zone can have limited access 101 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Configure other type of zones Interlock zone SiPass Entro offers the possibility for two doors to co operate in order to form an interlock zone This means that the first door has to be closed before the next door can be unlocked To be able to monitor the status of the doors both must be equipped with door monitor contacts Proceed as follows 1 Open the Installer gt 76 application 2 Choose tab Zones and click on new gt A wizard starts Enter a name and select Interlock Select the two doors Select if the second door
61. d the actual crypto key will work and the connection should be established Wait for an updated database icons are green 27 6 Installing an additional or replacing a SR35i 118 The reason for this is adding an additional controller replacing a working one more capacity or replace a broken There are several ways to configure a SR35i before connecting it to a system Sometimes it is easiest to use the RS232 port Remember that the SR35i have built in menu commands for checking and editing different parameters Before you begin Consider the risk of electro static discharge ESD and take actions to avoid this Ensure that the controller is erased e g via removing the battery Be sure the battery is not empty Especially if the controller has to be shut down and moved after programming That all details about the system parameters are known Also the system name should be known in case of a PC setup It is important that the set up is correct This means Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Maintenance Correct node address set with knobs Correct networking parameters IP address Netmask and Gateway Correct crypto key In some network solutions you will get help from the software to find a new SR35i node if the default crypto is used The condition for this is that it exists within the same subnet as the
62. der parameters If cards other than SiPass Entro cards are to be used and if they will be read differently you must change the card reader parameters 1 Oe IN 5 Open the Installer gt 76 application Choose on the menu System gt System settings Click the Card reader parameters tab Enter the type of access cards to be used in the system iPass Entro standard means that the system reads track 2 ISO format and positions 9 16 on the magnetic strip or the last 8 positions if fewer than 16 Standard SiPass Entro cards are encoded like this lf other cards are to be used and will be read differently click Custom Then enter from which digit position on the magnetic strip data should be read and how many digits should be read 16 at the most Some older readers maybe only read 8 digits You should consult with Siemens Building Technologies if you are in any doubt about this Select in which way the digits shall be presented in SiPass Entro 19 2 Personal code without card Generally PIN is used together with a card during the Card PIN security level However SiPass Entro offers each user the possibility of choosing a PIN instead of a personal card Note however that activating this function disables Group code This is how to activate the function YS SY oS Open the Installer gt 76 application Choose in the menu System gt System settings Click the Personal Code tab Choose the Use of p
63. e PC It is supported of a software driver USB Agent installed along with the SiPass Entro software is loaded when booting the computer There are also Kits available with the proximity reader PR500 Cotag or EM4102 technology together with a desk stand and USB RIF 2 3 5 Small applications without LAN 18 SiPass Entro is designed for use in smaller applications with only a few doors Other than correct planning it is often necessary to take use of some dedicated cabling You do not have to consider LAN IP addresses etc You just need some meters of cable a SR35i a Power supply and readers It s as simple as that Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment 3 6 Larger applications with without LAN SiPass Entro has the capacity of handling up to 512 doors and 40 000 people in the same system database In addition one PC can manage up to 10000 similar systems via modem and or LAN These systems consist of separate unique databases They can however be controlled and stored on the same PC The access control system should include one or several properties placed in different localities When one premises has many doors you can still use dedicated cabling The system is split into separate sections managed by its own SR35i Segment Controller This handles a couple of doors local bus All sub systems are th
64. e PC is stored in all segment controllers This has the advantage of being able to use the PC for other purposes or shut it off when it is not configuring or monitoring SiPass Entro EEE Each segment controller is delivered with 4 termination resistors 120 Q The Segment Controller is available in four different capacities which indicate how many doors it can manage SR35i 4 Controls max four doors SR35i 8 Controls max eight doors SR35i 16 Controls max 16 doors SR35i 32 Controls max 32 doors It is possible to upgrade and extend the capacity gradually This eases future expansion The SR35i communicates on two levels global and local bus It gives many choices of how to specify SiPass Entro Properties with several floors can include a SR35i on each floor which can handle a couple of doors each The most important is the SR35i Segment Controller which contains all data about the site Even the User name and password for the PC software package is included Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment Door controllers with remote card readers The door controllers are connected to the segment controllers A door controller controls one door where one or two in out remote card readers can be installed This combination split installation is designed for external doors or other doors with higher req
65. e PCs are needed In addition software updates and upgrades may apply Any expansion needs at least one operating PC connection to handle the necessary setup There is an option to reset to the factory crypto key before any expansion is done 27 2 RS485 In a system only using RS485 communication RS232 for PC just install new segment controllers and door controllers together with new cabling and power supplies All units will start to communicate immediately 2 3 Networking In a TCP IP based system the segment controllers and PCs must be installed correctly with correct P addresses and crypto key Door controllers and readers are installed as before Controllers are recommended to be of type SR35i It is possible to use the SR34i but the older SR32i or SR32 cannot be used If new SR35i controllers or PCs are to be connected to a TCP IP based SiPass Entro system they must be configured correctly There are two communication channels used for information exchange Between PC and SR35i through RS232 modem or TCP IP Between SR35i and SR35i through RS485 or TCP IP If the communication is done via TCP IP the crypto key must be loaded into all units Initially the default crypto key can be used However if RS232 is used instead for PC communication the controller can always be reached 115 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010
66. e configured in each unit Dependant of how the network is configured related to the PC in use routers firewalls etc some or all parameters have to be configured locally by means of the keypad and display in the SR35i The main setting is to use DHCP Proceed as follows 1 Power up the SR35i 2 Press buttons 2 gt 1 gt 2 gt 1 The controller will convert to the DHCP function and search for the IP settings 3 There are now also options to configure different parameters like DynDNS reporting options 4 Repeat for all SR35i that needs DHCP 90 Building Technologies 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure names and functions for doors 22 Configure names and functions for doors The next step is to configure names and functions for the connected doors Dependant of the type of door unit different menus is visible The example below applies for a DC22 door controller 1 Open the Installer gt 76 application 2 Click the Doors tab You will see the installed addressed doors as C1 D1 C1 D2 etc i If an installed door is missing in the list it means that the system has no communication with that door 3 Select the desired door if it is not already selected and click Edit Tip You can also right click and choose New Editor Delete 4 Inthe Name field enter the name for the door Maximum 32 characters 5 Check that the proper reader ty
67. e field 4 In the Entry doors Available box select which is reader IN 5 Inthe Exit doors Available box select which is reader OUT lf a person violates anti pass back i e does not use his card to leave a zone and then tries to enter the same zone or another zone the card will be blacklisted This function is used to specify for how long the card should be blacklisted 1 Open the Entro gt 76 application Choose the Zone tab 2 3 Click on the button Settings 4 Click the Anti pass back tab 5 Choose the desired alternative Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Configure other type of zones 25 2 Entrance limitation G When you create this type of zone you then have to decide which access groups will be able to enter the zone You will also need to specify the counter for each person 1 Open the Installer gt 76 application 2 Click the Zones tab then New For new zones a wizard is invoked which will help you configure the required functions For existing zones the tabs are shown displaying the same information Tip You can also right click and choose New Edit or Delete Type the name of the zone in the Name field In the Entry doors Available box select the doors to be included in the zone Click OK Open the Entro gt 76 application Click the Zones tab Mark the name of the entrance limitation zone an
68. e often used to power an access control system Here are some advantages Stable 24 or 12 Volt to electrical lock which normally only accept 15 Backup power for locks when main voltage falls An alarm can be generated if main voltage falls and battery powering starts Fewer units to install Easier to expand the system if enough margin from the start Note that SR35i has a lithium battery that keeps data when power disappears Connect the power supply according to the instructions below but do not connect the power to outgoing cables Power supply Mains 2 earth Local bus 4 screen AJ oe te Power supply failure connected to IOR6 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Power supplies Isolated communication The main idea is to form a system such as that illustrated in figure below where every segment is powered separately If this is achieved the risk of earth current is minimized because the only existing link between the segment controller is a galvanic isolated RS485 Note that also TCP IP LAN means isolation between SR35i Ka KE 8 8 8 SR35i SR35i I SR35i Isolated communication when using central power supplies 1 Global isolated RS485 communication
69. eeeeaeeeeeens 99 25 Configure other type Of ZONES ccccscseeeesseeeeseeeeeeseeeeeeeeeneeeseaneesseanneens 100 25 sAMU DaSS DaCk ROM Call snes in a a a a a a 100 252 Entrance MIM AUI ON sasaa a dere le ent Geese tuned a tone Vecsienersadtaut 101 2O 5191 0 1074 0 9 eee ener Remo ee eere aster eee nee eerie cee aera eee mene eee ares 102 25 3 1 Example Interlock cccccccccesccceeeceeeeseeceeeeseusesaueeseeecaeeseeeeees 102 26 CONTGUPE TOF FESCIVATIONN sosisus fosistandessssacceviceist diene kan daa ubia aa KA aAA aaa KN 104 26 1 Setup zones for reservation ODjeECt cccccceeceeeseeeeeeeeeeeeseeeeeeeeeeeesaaeees 104 26 2 Random allocation or NOT of similar reservation objects ccccseeee 105 26 3 Alarm control in a reservation ODjeCt ccccceccceeeeeseeeeeeeeeeseeeeeseeeesaneeesees 105 204 TUNG schedules tases ntsc i E a E E st 106 20 9 IRESCIVALION ODOC iristera E a O A 107 26 6 Enter public holidays and holiday periods in Reservation c0008 108 26 7 Decide on reservation authorities for ACCESS groups ccceeeeeeeeeseeeeees 108 26 8 Give persons reservation AUtNOLitieS ccc eccceeecccseeceeseeeeceeeeseeeeseeeesenes 109 26 9 Flexible reservation in Same Interval ccccccccceeeeeceeeeeeeeeeseeeeeaeeeseneeeeees 110 26 10 Show reservation information to the USED ccccceccecseeeeeeseeeeeeeaeseeeenaeees 110 ZOE SENICE MOE eax
70. en linked into a higher level of communication global bus Facility with RS485 cable E fe 2 DC22 DC12 DC22 GE L PR500 PP500 HD500 Facility with RS485 cable 1 Local RS485 bus 2 Global RS485 bus 19 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment Both TCP IP and RS485 use global communication When several properties exist in the same system a LAN may be considered Note that the numbers of doors cannot exceed 512 in up to sixteen segment controllers In this case the global bus will be connected via LAN TCP IP but each SR35i controls its own doors locally A combination of the two communication methods can also be possible as only one SR35i in the facility uses LAN whilst the others connect via traditional cable PP500 HD500 Both TCP IP and RS485 in global communication 1 Global communication 2 Local RS485 bus 3 Global RS485 bus 4 Local Area Network in same building TCP IP 20 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment Two systems with separate databases In some cases only a centra
71. eptionist has another PC with another license For every PC there must be a connection in SiPass Entro where the license number and communication ports are defined At the same time the applied filter events will only be sent to each PC respectively l e if the Security manager temporarily log on to the Receptionists PC no events will be received to this PC For every new System user you create you have to specify also the connection and which event filter is to be used The simplified illustration below shows how it works a a 6 TCP IP 1 Manager Login Filter 1 Events Receptionist Login Optionally Manager Login NO events received 2 3 4 Filter 2 Events 5 6 Connections to SiPass Entro system Instead if only one PC is used with several users the different filtered events will be stored in different folders on the PC dependant of the user logged on 24 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 8 2 Microsoft Terminal server 2008 The SiPass Entro software can be ordered as a Microsoft Terminal Server 2008 package which makes it possible to install SiPass Entro as a client server application Note that also MS Terminal Server 2003 is supported This means that the SiPass Entro software is installed on a central server PC The Terminal server appli
72. ersonal code without cards alternative Enter the desired number of digits to be used 4 8 in the PIN Any user choosing PIN without card must choose a code consisting of the number of digits chosen here Click OK 81 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Personalize Entro settings 19 3 Changing red LED function on readers By default the red LED is used to indicate an active alarm zone and will be lit on readers those are members of an alarm zone once the alarm system is armed To disable this function and use the red LED for door locked indication please proceed as follows 1 Open the Installer gt 76 application 2 Choose in the menu System gt System settings 3 Click on the Reader red LED tab 4 Check the box Use red LED for door locked indication 5 Click OK i This setting affects all readers on the system that are using BCLINK or RS485 connection i e not Clock amp Data readers If this is checked it will not be possible to monitor alarm system status We recommend not checking it if alarm zones are used 19 4 Duress code on off With the Duress function activated a person entering the building is able to enter a specific code if forced to open the door under threat Doing so an alarm signal is sent to a connected alarm transmitter When SiPass Entro is delivered the duress function is deactivated This is how to acti
73. es Notes when using SR35i and TCP Remember that any zones e g Alarm zones will work best if they reside in the same sub net when several SR35i use TCP IP between related SR35i 25 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 9 3 Example of SR35i with RS485 This solution gives a more closed system with dedicated wiring RS485 between the segment controllers Small application with one SR35i SR35i Small system with only one SR35I Larger application with several SR35i Several SR35i in a wired network 26 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 9 4 Example of SR35i used in Local Area Networks This version of SiPass Entro gives the possibility that several SR35i can communicate through local area networks and the system can be software controlled from any PC on the network No separate connections are needed between the controllers Note that it is possible to connect the PC directly RS232 or via the network Several SR35i with TCP IP communication 27 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 9 5 Example of SR35i using Internet In this case the Internet Local Area Network a
74. es routers firewall etc the correct settings O Yes Have all connected segment controllers readers and door controller s g Yes proper addresses Is the reader connected to correct terminal block in DC22 DC12 and is g Yes the power link correctly fitted Is a 120 ohm resistor fitted at the end of each RS485 communication g Yes circuit Does the resistance in all communication circuits comply with the values O Yes recommended in the manual Is each circuit s screen connected to earth in one place only 0 Yes Are the power supply equipment and cables properly dimensioned g Yes When Reservation is used is at least one CF8 installed in a SR35i g Yes Is time and date properly set when the system is on line g Yes Is any installed DVR properly configured g Yes 15 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Start the software 16 Start the software The first time you start the SiPass Entro software you will be requested to create a system user and thereafter logon again to be able to store events 1 In the Windows start menu select Start gt Program gt SiPass Entro 2 Choose one of the three applications Installer Entro or Door Monitor gt The login window is displayed SiPass Eniro Installer x SIEMENS Pati Connection Adee Connection penser hama Paneer 3 Enter the user name in the user name field default be
75. eueeeteneeseseeenaes 30 3 11 2 How the Reservation system is installed ccceeceeseeeeeeeeeeeees 31 Oo 12 Integrate CCTV SY SIG IM sue oaasccesSesdx ibaade a a i 31 3 13 Integrating with external applications BAPSI cc ccceecceeseeeeeeeeeeeeeeaees 32 IIE Gener gt Reemereenenee ete tee ce eet mn er E EA reer 32 313 2 Whats BAPSI used for ut tcsetccioctesta scat a a as 32 9 13 9 Pield applcatons sissnisen nie a ae eee ee 32 3 13 3 1 Application example External Reservation system 0 33 4 System TEQUIFEMONIS oia a a E at 34 4 1 Recommended system cables cccccccscccsseecsseeeseseecseseeseeeeeseaeeeneneeenees 35 Me MANO OS cred Nash asc occa oa aca ecto hrs cons teeta edness es acess ese aos oenaee hanes 36 4 2 1 Cable for power Supply ccccccccceececeeseceeeeeseeeeceueeesesesseeeesaaees 36 4 2 2 Cable fOr RSA Toros etches acc tee oo aed A eu el ciias 36 4 2 3 Cable for network TCP IP cccccccceccseseeeeeeeeeeseeeeeeseeeeeeeaeeeeeeas 37 4 2 4 Call GO POG oina a eae Ned aaah deea iba 37 4 2 5 Earthing and screening for RS485 cccecccesseeeeeeeeeeeeeaeeeeeeeaees 37 5 POWEM SUD DIGS cnicana a a a 38 3 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 4 5 1 9 2 5 3 5 4 5 5 6 1 6 2 6 3 6 4 8 1 8 2 8 3 9 1 9 2 9 3 9 4 9 5 9 6 9 10 10 1 10 2 11 11 1 11 2 11
76. g Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 2 System overview The system below is shown on three levels PC with software to send receive information to from the system via direct cable or network The InfoPoint IP811 terminal is used for reservation functions SR35i controllers hold information and make decisions as to the access granted at the doors Door environments where door controllers readers keypads etc are installed together with electrical locks InfoPoint 811 TCP IP SISTORE DVR RS232 A SISTORE DVR InfoPoint 811 SR35i SR35i U Camera Camera 1e PR500 E PR500 PD40 EM Different levels in the system 1a PC Security Controller 1b PC System Administration 1c PC Visitor Management 1d Local PC System Administration 1e Reservation Management Controllers Doors Intrusion alarm control relay output 2 3 4 Video surveillance system connection TCP IP 5 6 Control inputs and outputs 12 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Securi
77. guide As soon as you have established a LAN connection to the AX you can optionally configure the parameters from the PC Parameter Default value Optional User Value Comment User name lt Not set gt Entro parameter Password 12345678 Entro parameter IP address 192 168 1 129 Entro parameter Gateway 192 168 1 254 Entro parameter Subnet mask 255 255 255 0 Entro parameter names Port SR lt gt DVR 17655 N A lt Fixed in Entro gt Port Watch 8016 N A lt Fixed in Entro gt Port Admin 8200 N A lt Fixed in Entro gt Port Search 10016 N A lt Fixed in Entro gt Port Callback 8201 N A lt Fixed in Entro gt Camera no s and lt Not set gt Entro parameter The table is valid for the following AX devices SISTORE AX4 Lite SISTORE AX4 160 100 SISTORE AX9 AX16 250 50 Since SISTORE AX9 AX16 250 200 has enhanced user authentication a user name is mandatory for authentication with the device same for future SISTORE AX8 AX16 250 100 A default account is set up on the device user name admin no password It is a good idea to name the cameras equally in both the DVR and the SiPass Entro environment because otherwise it is a risk that the on screen name differs from the name seen in the SiPass Entro event log 71 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Install DVRs
78. he directory normally resides with the ISP and will itself also be accessed through an IP address which normally is supported together with the leased P addresses When DHCP is used and the ISP often changes the connected users computers leased IP address also the DNS must be updated with new information This is called dynamic DNS DDNS and means that equipment can ask this service for the latest IP address for a specific name 49 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Prepare any network resources 9 2 Subnet agent SR35i The subnet agent is a term used for a dedicated SR35i which administrate the communication between SR35i controllers who reside on a subnet of a local area network where routers are used Only the IP address of the router is visible outside the router The subnet agent solves this by administrating the traffic to the other SR35i on the subnet The router gt 51 is configured with the relevant parameters of the subnet agent If the subnet agent is using DHCP the MAC address must also be known so that the router gets the physical identity MAC of the SR35i Proceed as follows 1 Power up the actual SR35i 2 Press buttons 2 gt 2 gt 1 gt The MAC address is displayed as 12 characters Note this down for further use 3 Press ESC 4 Press buttons 2 gt 1 gt 1 gt The IP setting
79. ies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Maintenance License number e the number for the new computer This is noted on the CD case for the new software license Type of communication TCP IP RS232 or modem gt You have now created a new connection for SiPass Entro and can exit the program in the existing PC 2 5 2 Configure the additional or replaced PC Because this PC does not yet have any database stored nor know the way of communicating with SiPass Entro you have to create a connection also in this PC 1 Start the new PC and install the SiPass Entro software Note A separate software license is needed for a second PC Open the Installer application and select at login that a new connection shall be created for a new PC or an existing connection used for additional PC Follow the instructions on the screen similar to above gt You have now defined in which way the computer will communicate entered the system name login details etc Note if the Crypto key has been changed before the login will fail Instead perform also these steps Open the Entro application OFF LINE Enter the 32 character Crypto key manually in the System menu Shut down SiPass Entro completely by right clicking over the icons and select Exit the crypto key will be stored in the database in this PC Start the Installer again an
80. in the zone should open automatically or not Exit gt fF amp If security level is toggle card on a door in an interlock zone the second door does NOT open automatically when the first door is closed 25 3 1 Example Interlock The Door A has a card reader to the zone and an exit button from the zone The Door B may have exit buttons in both directions or have a card reader to the zone Depending on the type of installation the interlock zone operates slightly differently 4 L pi E N y L Q Example with two BCLINK readers PR500 1 Door monitor contacts 2 Electric Lock 102 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure other type of zones Access from Door A to Door B After entering door A which is then closed during the opening time door B will be automatically unlocked However if door A is closed after the opening time e g while the buzzer sounds during the Door Held Warning Time the exit button must be used to enter door B If no button exists at door B access must again be made from outside door A Access from Door B to Door A After entering door B which is then closed during the opening time door A will be automatically unlocked If door B is closed after the opening time e g while the buzzer sounds during the Door Held Warn
81. ing Time the exit button must be used to enter door A If only exit buttons are installed in door B no automatic unlocking will take place The Exit buttons have to be used for both doors 103 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 Configure for reservation 26 1 Setup zones for reservation object This section describes the steps for creating the doors and relays in a Reservation object Note that a common main reader for more than one reservation object will only work if the objects are grouped together 1 2 9 Open the Installer gt 76 application Click the Zone tab then click New For new zones a wizard is invoked which will help you configure the required functions For existing zones the tabs are shown displaying the same information Enter the name of the object in the field Name Select Reservation object and click Next Click on Add Remove doors and a new window is displayed with all SiPass Entro doors and all IOR6 relays specified for reservation use Add units to the Reservation object and Click OK gt A list of doors relays are displayed and completed with a new option field For each door or relay you now have to configure the function of them by choosing one of the following Main reader This is indeed the object you may reserve E g 18 00 19 00 Note that this option will only
82. ire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Configure IOR6 relay controller 23 2 Common alarm output The common alarm can be set to two different output types Pulse mode means that the relay falls back after a certain time Bistable mode means that the system will keep any activated relay state until the user performs acknowledge or another decided event occurs Proceed as follows 1 Open the Installer gt 76 application 2 Choose tab Doors and mark an IOR6 3 Click Edit 4 Mark any of the tick boxes for Common alarm in the tab IOR Relays 5 Every relay in the IOR6 can optionally be configured for generating an output signal Select function in the list box If pulse mode an event filter can control the relay Set the time the relay shall be active If bistable mode a new menu is opened where the criteria for the relay is further selected 23 3 Configure IOR6 for time control It is possible to use any IOR6 relay as a simple timer function similar to a door opening relay These relays will be displayed in the Entro program and allow for choosing individual time schedules for them The system allows for separate opening time for the relays as well as relays 1 4 which can be activated via input signals remote opening Proceed as follows Open the Installer gt 76 application Choose tab Doors and mark an IOR6 Click Edit Choose
83. it is not possible to connect to the SR35i from the PC E g ina remote site environment Instead the menu system in the SR35i can be used to configure the network settings There is a built in keypad and display which enables also for entering letters Ensure that the settings are aligned with the setting in the PC software database See section SR35i Configuring gt 86 20 2 Create multiple SR35i for combined TCP IP amp RS485 communication 84 The combination of a local network and RS485 requires that the controller used for TCP IP has to be set up as in the earlier section All other SR35i using RS485 will be displayed with temporary symbols C1 C2 etc The number refers to the segment controller s address Then proceed with the steps in the section SR35i Configuring gt 86 RS485 RS485 RS485 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Contigure names for segment controllers 20 3 Create multiple SR35i for only RS485 communication Systems intended for RS485 no local network are configured via direct cable RS232 In this case all controllers will be displayed as C1 C2 etc where the digit corresponds to the address jumper Then proceed with the steps in the section SR35i Configuring gt 86 RS485 RS485 RS485 85 Building Technologies 020_SiPass_Entr
84. iveld 49 S bnet agent SRJ areea e a a aA N 50 FROULCF SOLID ananena A a N 51 DWV AIDING sosina aaa aa aa testo 51 9 4 1 Configuring of DynDNS org cc cceccseeeeeeeeeeeeeeeeeeeeaeeeeesaeeeeeeeaees 52 FIO Wal ases an aa a a a a A 92 Example WIth TOULCR aerate ananda ia a a ae 53 Apartment building CxAMple ccccccccecccseeeeseeeseeeeseeeeseeeeseeesseeeseeeeseeess 54 Installing the software eee ceeceeeeeeeeeeeeeeeeeeeeseeeeecaseeeaaeeesaaeeseaneeseenessoaes 55 Creating a basic database ANd CONNECTION cccccceeceeeeeeeeeeeeseeeeeseeeeees 55 10 1 1 Automatic detection Of UNItS cece ccececeeeeeeeeeeeeeeseeeeeeeeeeees 57 Multi user environment more PCS c cccccccceeeeeceeseeeceesseeeseeseeesseneeessees 58 Installing modem based SYStOMS ccccceeeeeeeeeeeeeeeeeeeeeneeeeneeeeneseeeeneaees 59 Configuring a system equipped with TD36 modem recommended 60 Configuring a system equipped with a custom modem cccseeeeeeeeeees 60 Configuring the modem based system on site 0nnnn0nnn0nnnannnennnnnnnnennnnnnnn 60 Mount and configure the modem c cccccseececaeceeeeececaeecesaeeeseeeeesaeeesanees 62 Transferring the new system s information to the central PC 04 63 Installing the CF8 flash memory card cccceseeeeeeneeeeeeeeeeeeeeneesseeneensees 64 stall DVRS pecia ai 65 Proreg iShteS ae epee i 65 DVR CON
85. k monitor 92 Lock monitor contacts 91 M MAC address 50 51 Machine control 31 Memory card 30 Modem 59 60 Multi user 58 MX 68 N Netmask 86 O Overlap time 107 P Password 76 Patching 120 Personal code 81 Ports 51 66 Power failure 94 Power supplies 39 Power supply 38 printer 48 R Readers 119 Reservation 10 29 128 Reservation object 104 107 Router 51 RS232 48 83 RS485 25 S Server 25 SISTORE 31 65 SNTP 80 SR34i 116 SR35i 83 116 Static P addresses 49 Subnet agent 50 T TCP IP 25 83 Terminal Server 2008 25 Termination resistor 74 U uninstall 121 User name 76 V W Wall socket 48 Web server 30 Viewer 65 Wireless 29 Voltage drop 74 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_A24205 A335 B317_e_en 10 03 2010 Index 129 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Index 130 Building Technologies 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Issued by Siemens Building Technologies Fire amp Security Products GmbH amp Co oHG Siemensallee 84 D 76181 Karlsruhe www buildingtechnologies siemens com 2010 Copyright Siemens Switzerland Ltd Technical specifications and availability subject to change without notice Document ID A24205 A335 B317 Edition 10 03 2010
86. k settings for SR3SOI cc cccceeceeeceeeeeeeeeeeeeseeeeeesaeeeeseaees 87 21 2 Customize the database for DHCP ce cecececcececscereeeececscueareneess 89 21 3 Prepare the SR35i component for DHCP 0 cece eecceceeceeaeeeeeeeeeseeeeeees 90 22 Configure names and functions for doors c sceeeeeeeeeeeeeeeeeeeeeeeeseaenees 91 23 Configure IORG relay Controller cccccecseeeeseeeeeeeeeeeeeeeeaneeseeneeseeneesenes 92 5 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 6 23 1 DOOF lock monitor OULDUE sixes coe eds ee en ade eee ee 92 29 2 COMMON alal iii QUID UN e526 5 205 ieee a a bot ela 93 23 3 Configure IORG for time control eee cceceeeceeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeseeeeeeeas 93 23 4 Power failure Warning INDULt c cc cecceceeeeeeeeeeeeeeeeeeeeeeeeseeesaeeseeseeeeeeesaaeeeeas 94 23 5 Emergency Opening INPUL ccccccccssececeseeecsseeceseeceaseessseesseeeeneueeeneuess 94 235 0 CEXCHUKON lt sIN DUN c ceietarasb as cele abet T sod dod pees Te 94 23 7 Configure IOR6 for Reservation system ccccceeceeeceeeeeseeeeeeeeeeeeesaeeeeeens 95 23 0 LAR GOnMtrol WIth ORG ascii sncei heb ecaseet lated a elieaauiect 95 24 Configure Intrusion Alarm zones ccccceeseeeeeeeeeeeeeeeeeeeeeseeeeeeneesseeneensees 97 24 1 Decide on security levels for alarm control cccccceeeeeeeeeeeeeeeeee
87. l PC can manage different unique systems in different facilities This can be obtained via modem or LAN See figure Network connected PC for two separate SiPass Entro Network connected PC for two separate systems 1 PC with two different databases each with separate login Global network or Internet encrypted TCP IP Local Area Network AVN Gateway 21 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 7 Communication with PC SiPass Entro SR35i offers three ways of communication with a PC By default the software installation assumes that only one computer shall log on to the system If several computers users shall log on at the same time more so called connections must be setup 3 7 1 Local Area Network G 22 In this configuration the Local Area Network Ethernet 10 100 Mbit is used for TCP IP communication with the PC It is very important that the IT manager of the end user has participated in and has approved of all aspects of this part of the installation Note that the SR35i has an integrated network switch with two connectors RJ45 where a PC and an SR35i can form a local area network without any extra equipment except for the cable Directly connected without LAN In this case the PC has static IP address and is connected directly to the SR35i as an
88. l SR35i 2 Install the CF8 card 3 Reconnect the power to the SR35i When all other necessary parameters and units for Reservation are configured you can connect to the IP address of the SR35i http xxx xxx xxx xxx login html and the login page should be displayed Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Install DVRs 13 Install DVRs SiPass Entro has integrated functions for controlling an external DVR system in the Siemens SISTORE range There are different capacity and settings depending of which DVR product that is used This describes which parameters to set in the different SISTORE models and which additionally cautions to consider getting them work in the SiPass Entro environment i For all models it is recommended to print the documentation on the CD supplied with the DVR before any configuration is done 13 1 Prerequisites We assume that the DVR system is installed and documented according to its handbooks and that the DVR have been configured for communication with the SiPass Entro system E g must the LAN environment allow for communication between the units Normally there is an user interface PC software for the DVR system meaning that initial settings are done with this software or in some units basically by means of the front panel in the DVR NOTICE Always calculate on the number of cameras used frame r
89. l also see any other functions this zone can be used for 5 Click Next In the Entry doors Available box select the door s to be included in the alarm by pass zone 6 Click Next 7 Select the door which is physically connected to the intrusion alarm control unit 8 Inthe Alarm by pass relay operation list box select the alarm control method to be used 97 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure Intrusion Alarm zones 98 9 10 11 12 13 14 15 16 17 Bistable function Used if you want to fully control the intrusion alarm You may deactivate the alarm after it has been activated by using your card at the reader and entering your PIN To activate the alarm press B and use your card at the reader or B card PIN You can use a push button if fitted connected to the alarm activation input of the DC22 Automatic alarm activation can be achieved by using a specific time schedule for alarm control Bistable pulse This alarm by pass method is similar to bistable function but instead of the output remaining operated a short pulse is generated for both the switch on and switch off operations Decide if the Alarm activation warning shall be used In case enter in the warning time field duration for how long a warning buzzer should sound before the alarm is activated between 5 1000 seconds 16 5 min
90. lect modem enter the telephone number to the SR35i modem Proceed by clicking Finish Incase of RS232 the software automatically detects the correct COM port in the PC Proceed by clicking Finish Ifyou select TCP IP the wizard needs more parameters Proceed by clicking Next 2 Select Static IP or dynamic IP address DHCP Enter the IP address of the SR35i to connect to if static is chosen If dynamic IP is to be used follow the instructions on the screen Note that the SR35i component gt 90 needs to be properly configured The built in keyboard and display can be used 3 Click Finish and the Installer main window are displayed CAUTION 56 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing the software It is very important that you make a note of the system name If you have to replace the PC this system name must be entered before the system will work again Normally you will now see detected units where you then select either to configure all units or at least one SR35i according to the section Automatic detection of units You should now wait until both indicators are green gt 77 before continuing As long as you are still in the Installer program the events will be displayed in the Door monitor application if started 10 1 1 Automatic detection of units The Installer program has embedded functions for
91. ller or the one stated initially when locally setting up SR35i Enter the Netmask which can filter the addresses for messaging on the LAN Often the value 255 255 255 0 can be used Enter the address for Gateway if one exists This can be used to take care of rejected addresses filtered by the Netmask Enter the IP address for any Domain Name Server if e mail functions are to be used Optionally both the IP settings DHCP and the DNS server address can be obtained automatically by clicking the check boxes respectively Note that the DynDNS functionally must also be setup in the software as well as in the SR35i Enter the actual mail server SMTP used in e g the Reservation system Enter the network identity for the segment controller Click on the tab Time if displayed and enter a correction value 1 2 1 2 etc This should correspond to the geographical time zone where SR35i is installed Compare with GMT time and the setting in an ordinary PC e 0 for Great Britain 1 for Sweden and 2 for Finland Click OK and continue with the next segment controller until all the segment controllers on the system have been named Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 SR35i Configuring 21 1 Decide on network settings for SR35i When the system allows for DHCP in SR35i some more settings must be considered When DHCP is selected every
92. mmy local area network which only consists of a directly connected SR35i and a PC In this case you use a network cable between the PC and the network switch in the SR35i i If you connect a temporary PC with network cable direct to SR35i we recommend that also the PC use a static IP address Preferably in the range 10 1 200 xxx with Netmask 255 0 0 0 because the SR35i initially is set to an IP address in this range 47 020_SiPass_Entro_6_5 A24205 A335 B317_e_en 10 03 2010 Building Technologies Fire Safety amp Security Products Connect the PCs or an online printer 8 2 Connect PC with direct cable RS232 G The segment controller must be installed close max 25 meters to the PC The illustration below shows an available complete kit consisting of a wall socket IF1 a standard RS232 cable approx 1 2 m and 25 meter cable with one free end to connect to the screw terminal block of the wall socket You can use the standard cable directly alt 2 between the PC and the SR35i or make a more fixed installation alt 1 RS232 needs fewer settings in the PC which simplifies the set up You can also temporally use RS232 and then change to Ethernet later lt 25m Alternative 1 3 is oO Alternative 2 fina 2 2 7 7 gt E RE 8 1 2m 5 5 Two alternatives for RS232 cabling The total distance between PC or printer and the segme
93. n the circuit or the termination is missing in both ends If using a LAN check that all cables are correctly connected to the LAN 14 2 Check the power supply 74 Connect the power supplies Check that the voltage is approximately that of the power supply output and that and are in the right positions Remember that a voltage drop between the highest and lowest potential larger than 5V between units may influence the quality of the RS485 communication Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 15 Checklist Checklist The checklist below is a useful aid when installing SiPass Entro It will also make sure the implementation will run smoothly If you have questions do not hesitate to contact technical support The operating system in the system s PC is Oj 2000 g XP g Vista O Terminal server 2008 O Terminal server 2003 O Windows 7 If RS232 is to be used are there free serial COM ports 9 25 pin plug in O Yes the system s PC Is the wall socket RS232 installed close to the system s PC and g Yes connected to a suitable SR35i and is the total distance between PC and SR35i less than 25 meters If local area network is to be used does the PC have a correct g Yes connection Have the SR35i got correct IP addresses authorized by the IT g Yes Manager Have all networking resourc
94. n of equipment 3 1 Software description 3 1 1 Software applications 10 The SiPass Entro software consists of three applications Installer This application is used for setup of the hardware Install PC Controllers and door monitor contact and alarm zones Entro This application is used for configuring and managing access groups and persons cardholders It can be treated as main part of the software because it is used for daily operations The following functions are integrated in the Entro Access control Add Cardholder choose and configure Caretakers create Access Groups create Time Schedules Zones anti pass back zones roll call zones entrance limitation zones Card printing badge printing Create your own card design and print it on an industry standard cards Video Surveillance CCTV integration The SiPass Entro system can be used in combination with a Siemens CCTV system A connection can be done from the SiPass Entro software directly to install and maintain the CCTV system e g DVRs and cameras Intrusion alarm system control A common application for the SiPass Entro is beside access control to control an external intrusion alarm system by means of an access card Reservation function The System Administrator sets which objects such as card readers doors are to be included and chooses the relevant reservation time schedules The users wanting to reserve times can use an ordinary web b
95. n the SR35i intended for reservations Depending on how the reservation function is specified one or more InfoPoint IP811 or touch screen terminals can be connected to the system through the network e a combination of PC and these terminals is possible Technically the entire reservation information is stored in an integrated website in a SR35i with its own IP address on a network Configuring is described the User Manual The address to this website is http xxx xxx xxx xxx login html which should be notified to the users of the Reservation system 3 12 Integrate CCTV system The SiPass Entro software can communicate with up to 16 DVRs via TCP IP It supports DVR units in the Siemens SISTORE AX CX and MX range We recommend that the installer have good knowledge about DVR system in general and SISTORE systems in particular before any DVR functionality is introduced into the SiPass Entro system Implementation The integration of DVR and SiPass Entro indeed consists of two separate hardware systems which are connected via TCP IP and remote software functions This means that you initially install software components for both systems in the same PC When you then configure functions like filtered and timed triggering to start recording in the SiPass Entro these are then sent to the DVR When the conditions for a certain action then are met the DVR starts recording images You may then replay these directly from the SiPa
96. ng BAPSI custom application software can take advantage of sending receiving messages to from the access control system and easily add new functions into the overall system This could be Time amp Attendance Reservation systems etc External Application Program direct lt Interface External Application program Program 3 13 3 Field applications At the moment there are already systems running in the reservation applications area using the BAPSI software interface In this case the supplier of the external reservation software made a modification to their software module which writes data into a file and Siemens Building Technologies developed a special module that reads this file and forwards this information to the access control system 32 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 13 3 1 Application example External Reservation system Siemens Building Technologies have mainly for the Swedish market developed an application based on BAPSI called BAPSER which allows for sending data between SiPass Entro and external reservation software at the moment Idavall Fri and Argentum Booking The module is installed in the external PC that uses a TCP IP link to send the reservations to SiPass Entro If you intend to use BAPSI in some way the SiPass Entro must have some parameters set up This is desc
97. nt controller must not exceed 25 meters maximum The RS232 port can also be connected to a printer Note that either a PC ora printer can be connected to a segment controller not both 8 3 Connect an on line printer RS232 48 To set up an on line printer to print events directly from a SR35i please proceed as follows 1 Open the Installer gt 76 application Go to System settings gt Connections and enable multiple connections Select New Select Printer for event logging and click Next Define name for the connection Specify which SR35i that the printer is connected to vo oF ff amp N Specify event filter to use The following parameters apply for the RS232 interface 9600 baud alt 57 600 baud No parity 8 bits 1 start bit 1 stop bit Printer output with hardware handshaking character table ISO 8859 1 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Prepare any network resources 9 Prepare any network resources G Before you install the software there are some resources that need to be defined and configured Also remember that some SR35i requires that DHCP must be configured via the SR35i menu system gt 90 The End Users Buyers IT manager should always participate in the planning of a TCP IP based SiPass Entro system General knowledge about networking is also recommended 9 1 Background Static I
98. ntro gt 76 application 2 Click the tab Zones and Edit the object 3 Go to the Debit tab You will see an edit box for each event type 4 Select a value in the form xxxx yy for each event The format of the values will follow the Windows format for numbers 5 Click OK The system stores these values along with event in the ordinary event files but does not display them in the event log on the screen To evaluate them use the Door and event monitor application and export the result into a text file for further actions in external software Alternatively transfer the information via a BAPSI application i Note that if you change the debit values according above after the time of the event the original will be exported no corrections 26 13 Configure for e mail confirmations SiPass Entro can automatically generate an e mail message to the person making a reservation or a cancellation The texts in these messages are stored in two files in the CF8 compact flash memory card and may be edited but this is normally not necessary The messages also include the IP address to the web server SR35i that sent the message This gives an easy way to log in again for editing reservations i The name of the SR35i sending a confirmation allows only characters accepted in e mail addresses Special national characters cannot normally be handled by the e mail server ISP 111 Building Technologies 020_SiPas
99. nts On every event set to alarm Means that the segment controller calls the PC following each alarm event On database changes Means that the segment controller calls the PC following each modification in the database This only applies if another PC is connected to any of the new system s segment controllers A call is made every 15 minutes if the database is modified 15 Click OK Now you have configured all the information about the new system 16 Disconnect the PC you have used for configuring the system and connect the modem gt 62 instead i Activation and deactivation of alarms as well as PIN alterations are a database modification which means that calls will be made every time this occurs Entroser must be running in the PC to be able to receive calls about database modifications 61 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing modem based systems 11 4 Mount and configure the modem The illustration below shows how to connect a modem to the segment controller used for communication with the PC 9 pin DB9P OV Frame When the modem is installed the installation is completed The only thing remaining is to transfer the information configured for the new system to the central PC used to configure both systems Minimum requirements for modem 9600 bit s Auto answer off DTR disconnected Command echo di
100. o_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 SR35i Configuring 21 SR35i Configuring G 86 In a new TCP IP based system you will when invoking the Installer program have the opportunity to add more not yet configured SR35i that the software finds on the LAN You will see them in a list Just select any one of them to be included i 2 10 Open the Installer gt 76 application Select the desired segment controller if it is not already selected and click Edit Tip You can also right click and choose New Edit or Deleted In the Name field enter the segment controllers name A suitable name is the room where the controller will be placed e g Reception Avoid using names that may later be confused with door names Mark the tick box Proxy for SR35i using TCP IP If RS485 is used between all SR35is but PC connection uses TCP IP the only need for proxy in the SR35i is for reaching an SNTP Time server If there is a mix of RS485 and TCP IP the segment controllers using TCP IP must have Proxy function Decide if the SR35i also should act as a subnet agent gt 50 similar to a gateway for other SR35i controllers behind a router Select the Network settings tab and enter the IP address Netmask and Gateway When powering up the controller the IP address will initially be 10 1 200 1xx where xx indicates how the address is set in the contro
101. oller at a time is updated 5 Click on Finish gt A progress bar is displayed for each controller showing the remaining time 6 You can cancel the process at any time by clicking Cancel update gt No update is performed and the old version remains 27 9 Saving restoring database on CF8 Normally the SiPass Entro database is stored in all PCs and all Segment controllers The installer may also use the menu system in the SR35i SR34i to store or re store the database to from an existing CF8 memory flash card However this method shall be considered as an emergency operation and must be used with caution You should be very skilled and experienced with SiPass Entro before using this method In doubt please contact Technical support 120 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Maintenance 2 10 Door controller firmware control G If the door controllers DC12 DC22 and the PD40 EM PD40 EM have firmware version 1 20 or later the Installer program can download new firmware via the system bus This requires that the units are on line During download the door is unlocked if this is defined in the Security level in off line condition All other selections results in a locked door 2 11 Printout of system configuration In the Installer program you can generate a graphic view of installed components for easier control of e g current firmw
102. onfigured to be able to communicate with the DVR at all The communication between the DVR and SiPass Entro is done via a TCP IP link In the SiPass Entro a connection must be created for each DVR i In a single PC based system the tab Connections will not be visible directly You have to go to the tab System gt Systems settings gt Connections and configure the SiPass Entro to work with several connections like a DVR Proceed like this 1 Open the Installer gt 76 application 2 Click the tab Connections If not visible see the note above 3 Click New and select SISTORE DVR in the wizard 4 Enter the suitable Name of the DVR 5 Select which SR35i to use 6 Inthe list box choose DVR type This choice will implicitly also configure the SiPass Entro database to use the default network ports in the DVR 7 Enter the selected User name amp Password 8 Click OK 9 Repeat the above for each DVR 66 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Install DVRs 13 3 How to control recordings There are different ways to start recordings from the SiPass Entro Event triggered during time zones Continuously recording by time zones Manually recording started from the Door and event monitor application Event triggered during time zones Different event triggers in SiPass Entro can result in an automatic recording and
103. ore of the available objects to be accessible for this group 6 Click OK 108 Building Technologies 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 8 Give persons reservation authorities In a reservation system it is important that every person has a Member group no even if it is the same for all persons Otherwise the person cannot reserve any times Note We only describe additional information regarding Reservation Every person must belong to one or more access groups simultaneously These may already been given reservation rights If not you first create a new access group and proceed as follows 1 Open the Entro gt 76 application gt The Persons tab is displayed Mark a person and click on Edit lf you enter a persons e mail address in the Free field SiPass Entro can confirm a reservation by sending an e mail message if the software is configured for this See paragraph Prerequisites for confirmations gt 112 Check or choose correct access group Now decide on the Member group settings All persons belonging to the same member group will automatically have the same rights in the reservation system These may be e g training groups families etc There exists two methods of entering the parameters depending of the numbers of Member classes previously configured in the object Default one class Enter only the membe
104. other solution with one controller with two BCLink readers gt 42 sub addressing are considered 43 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Special installations 6 3 Intrusion Alarm Zones with DC22 The DC22 door controller must be used if any bistable intrusion alarm system shall be controlled by the SiPass Entro system To gain highest security you normally install and use card readers with PIN pad in all doors that are used for entrance to the particular section of the intrusion alarm system You may then use the security level Card for arming the alarm and Card PIN for disarming If any section area of the intrusion alarm system includes several doors the SiPass Entro must be configured with one or more Alarm zones Each zone must then consist of at least one DC22 with the relay while the other doors can remotely control it via the SiPass Entro system bus The illustration below shows how two separate zones may look like 1 Intrusion DC22 ci Alarm Pa Controller a a 444 aL a r 2 A a oa A aA DC12 DC22 eam oor 4424 B l agap Sa DC12 Example of Alarm zones 1 Arming signal for Zone A from DC22 2 Status signal for synchronization between systems to DC22 3 Arming signal for Zone B from DC22 4 Status signal for synchronization between sys
105. ove settings Controllers lt Edit IP Sddress Wetmaskt anew ays Bomam Mame Server Network setting in the SR35i 88 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 SR35i Configuring 21 2 Customize the database for DHCP lf DHCP is used you must now decide on how the segment controller should communicate with each other All SR35i using TCP IP must have the Proxy tick box marked Proceed as follow to allow for DHCP function 1 Open Installer gt 76 application 2 Choose on the menu System gt System settings 3 Click the Dynamic DNS Service tab System Settings x System name Card reader parameters Personal Code Dynamic DNS Service Connnections ReaderredLED The controllers that are using DHCP and that needs to report their IF addresses dynamically to a dynamic DNS service so that other hosts may connect to it can use the built in support For DynDns org Dynbns org account settings Account type Dynamic DAS bd DynDNS user name MyAccount DynDNS Password eeeeeRERE8 cane He 4 Use DynDNS org and enter the Account type User name and Password 5 Finished 89 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 SR35i Configuring 21 3 Prepare the SR35i component for DHCP If the SR35i will use the DHCP function this must b
106. pe is shown in the Terminal type field If you are using zones there may be a choice of readers if an EXIT reader is installed 6 Click the Relays tab 7 Select the checkbox Use relay for alarm by pass if a Monostable alarm locally will be used in this door It can belong to a bistable alarm zone but cannot physically connect to the Intrusion Alarm Control unit Monostable function Used if you want to by pass the alarm for a short amount of time e g for an entrance The by pass time is equal to the opening time the door held warning time Doors with Monostable function cannot connect and control the zones in an intrusion alarm 8 Ifthe door central shall control a motor lock mark the tick box for Motor lock Click the Door control tab 10 If door monitor contacts are used click the Door monitor contact exists check box Enter whether the contact is closed or open when the door is closed 11 If lock monitor contacts are used click the lock monitor contact exists check box Enter whether the contact is closed or open when the lock is locked 12 Enter by choosing one of the alternatives Lock at once when door is opened or Lock when door is closed again how the door is relocked after having been opened This will be dependent on the type of lock installed 13 If IOR6 lift control is used see section Lift Control with IOR6 gt 95 14 Click OK 15 Continue with the next door until you have named all doors and described their
107. pendent on the settings in the software Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 FAQ A stop in the communication with the PC has the same effect as if the PC is turned off e all data is still stored in the system together with an amount of events Then the communication is established again and the PC goes on line all events are transferred automatically 125 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Important information form 29 Important information form Important information about the Access Control System Regardless if any of the following information has been changed the fields below should be filled in and kept in a safe place They will be needed if the system is to be changed in any way System name Encryption key 4 x 8 digits 0 9 A F Password Installer program Name Password Password System User Master Name Password Computers and connections Name License number Connection O TCP IP 0 RS232 O TCP IP O RS232 O TCP IP 0 RS232 O TCP IP O RS232 O TCP IP 0 RS232 O TCP IP O RS232 O TCP IP O RS232 126 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03
108. r connection of a modem Below is an example of a configuration where a PC has direct contact with one SiPass Entro system and modem contact with another Example of a modem based system managed from a PC in combination with a wired system 1 System 1 2 System 2 59 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing modem based systems 11 1 Configuring a system equipped with TD36 modem recommended We strongly recommend using the TD36 at the site when using modem communication because it has e g a watch dog If you have installed a modem TD36 at the remote site and its telephone number is available there is no need to do the configuring on site You can connect the SR35i to the modem hook on the line but do the configuring at the host computer instead even if this may take longer time See more about transferring the new system s information to the central PC gt 63 However if you still want to configure it on site you do this through the RS232 link and then switch to modem when it is done Proceed according to the section Configuring the modem based system on site gt 60 11 2 Configuring a system equipped with a custom modem lf another modem not TD36 is used there may be a need of changing the init string of the modem and configured on site via RS232 You should then temporarily connect a PC
109. r group nr direct on the general tab above the card number Two or three classes also click on the Member group settings tab and select a Member class You will see all persons in the same member group Click OK Repeat necessary steps for every person i NOTE 1 Check that the access group allocated to a person has the correct reservation object associated see Access groups NOTE 2 You can simplify the configuring of cards persons even for the reservation by using the Duplicate function 109 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 9 Flexible reservation in same interval In many cases such as conference rooms you do not want to be restricted to reserving one or more short intervals you would rather have a more flexible way to reserve times The software allows for defining a longer interval e g 8 AM to 6 PM where the user then can reserve a flexible time within this interval e you first restrict the total outer limits start and stop but the user can reserve the whole or part of it Proceed as follows 1 Open the Entro gt 76 application 2 Click the tab Zones 3 Mark the actual reservation object and click on Edit 4 Create or Edit the time schedule to be used Normally this results in fewer but longer intervals a Mark the tick box Accept flexible reservation periods on thi
110. ribed in the documentation supplied with the BAPSER but you can invoke the menus by proceeding as follows 1 2 3 4 5 Open the Installer application and click on Connections Click on New Select BAPSI external application integration and proceed Enter the necessary parameters applying to the actual application Click OK 33 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 System requirements 4 System requirements 34 Recommended minimum specification for PC Processor 1 GHz 512 Mb RAM CD ROM drive VGA colour monitor 1024 x 768 Local Area Network connection or serial port for connection of segment controller modem Windows 2000 XP Vista Windows 7 or Microsoft Terminal server 2008 2003 functionality We recommend that the latest available operating system Service Pack is installed Citrix platform supported Basic requirements for network Twisted pair Ethernet 10 100 Mbit connection Communication between SR35i is done through TCP IP We recommend static permanent IP address for every SR35i often also Netmask and Gateway are needed We recommend permanent active Internet connection of SR35i when Internet is used Note when Internet connection is used the following ports have to be open in fire walls or similar and configured as follows 4002 if communication is used between PC and the chosen
111. rowser such as Internet Explorer Alternatively use his her card in a reservation terminal InfoPoint IP811 depending on how the system is configured Printouts Door Monitor This application is used to display event logs door status and video sequences It can be also used for unlocking doors via the PC Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Description of equipment 3 1 2 Software windows Entro starting window When the Entro application is started the following windows is displayed showing the list of persons SiPass Entro File System Search View Help ake Y Mame Member Group Bill Smith George Anderson Jill Parker visitor 1 Find Persons For Help press F1 ON LINE DE UP TO DATE 2009 05 a Entro start window Shortcuts There are two shortcuts sometimes available in the software to help creating editing or deleting information They appear e g in the Access group properties and in the Person s properties B Shortcut to Time schedule a Shortcut to Access groups E g when you create a new person click on the shortcut Access group if you have not yet created a suitable one In the same manner you can click further to Time schedule if you want to create or edit a time schedule In all cases you will come back to the previous step when you exit the menus 11 Buildin
112. rrent consumption at each unit Ampere Cable area mm Length m Resistance factor for chosen cable ohm m It may be easier to understand voltage drop by using a simple example ADEE 24 Volt K Example of cable 1 100 m System cable 2 DC12 PR500 with lock strike Method of calculation Note Always calculate with nominal battery voltage 24V or 12V despite a battery backup output voltage may be higher and maximal load at the units Current consumption at reader lock Ampere 0 160 A 0 100 A 0 260 A Cable area mm 1 5 mm Length m 100 m x 2 both directions 200 m Resistance factor for system cable ohm m 0 0112 ohm m Resistance 0 0112 ohm m x 200 m 2 24 ohm Current 0 160 A 0 100 A 0 260 A Result 2 24 ohm x 0 260 A 0 58 V voltage drop e 24 0 V 0 58 V 23 42V at lock This is sufficient for a 24 Volt electrical lock Result with 12V DC system In many cases a 12V application consumes more current than in the case of 24V With this in mind we assume that these units need 0 5 A Result 2 24 ohm x 0 5 A 1 12 V voltage drop e 12 0 V 1 12 V 10 88V at the lock which is on the margin but still is sufficient Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Power supplies 5 4 Example of a typical power supply section By placing the power
113. s are displayed Note this down for further use Example of a subnet with a router 1 One SR35i is acting as subnet agent for the subnet dashed 2 The other SR35i are managed by the subnet agent 3 Router where ports are opened and the IP address and or MAC address is configured for routing 50 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 9 3 9 4 Prepare any network resources Router setup DynDNS Any router used in a SiPass Entro system need to be setup to manage the communication correctly This means that the ports used in SiPass Entro must be opened See the handbook for the router in use how to change settings Proceed like this 1 Confirm the IP address for the dedicated subnet agent SR35i If the subnet agent uses DHCP also the MAC address gt 50 of the same SR35i must be known 2 Configure the IP address and or MAC address into the router so that the router knows where to route the information sent on ports related to SiPass Entro 3 Configure the ports according to below TCP 4002 Communication from PCs TCP 4011 Communication between SR35i TCP 80 Reservation functions If used UDP 123 Network time functions 4 Repeat the above if any other router used in the system DynDNS reporting in router If the router has the option to also manage the reporting of a dynamic DNS gt 51 it could
114. s object Click OK 26 10 Show reservation information to the user If some kind of maintenance or service is scheduled it is possible for personnel to set this up in the software Proceed as follows 1 Open the Entro gt 76 application 2 Click the tab Zones 3 Click on Settings and the click the Web Settings tab 4 Select appropriate alternatives Show Name of Person Show Member Group Numbers and Show all reservations 5 Click OK 26 11 Service mode If some kind of maintenance or service is scheduled it is possible for personnel to set this up in the software Proceed as follows 1 Open the Entro gt 76 application 2 Click the tab Zones 3 Mark the object and click Edit 4 Click on Set Service mode and select date by picking in the calendar and time for start and stop in the list boxes or mark the tick box Until further notice 5 Click OK and you will see the chosen time To edit the time just click the same icon again If you want to delete the chosen time just click Clear service mode 6 Click OK 110 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 12 Setup for debit function SiPass Entro has a function for exporting additional information about how reservation objects are used not used Any event associated with reservation will have a value Proceed as follows 1 Open the E
115. s seen as very reliable A breakdown often appears in the installation and set up phase or because of poor planning If there however is an accident the SiPass Entro has a range of technical solutions that eases a fast trouble shooting and repair E g removable straight through terminal blocks support even a change of parts when the system is still running somewhat like plug and play Under normal preventive efforts we think that SiPass Entro with its integrated monitoring functions and distributed intelligence is very good alternative with good redundancy to reasonable price level Why use battery backup UPS One of the best insurances against breakdowns etc is to install the necessary amount of battery backed power supplies A correct planning regarding number of doors type of locks distances cable type etc is then of course a prerequisite We recommend every SR35i together with its doors to have its own power supply if it is possible First because of it gives a cleaner installation Secondly it is possible to connect a power fail signal from the power supply to the system by using an IOR6 Every segment of the system can then separately be monitored for main voltage break downs An alarm event can be sent to the PC and or an external alarm system via IOR6 What happens if a SR35i gets a short interruption Every SR35i as well as the PC have a complete copy of the database mirroring As long as the hardware is
116. s well as RS485 are used for communication between units For example some PCs can be used only for login to a Reservation system via the Internet and other PCs could be used also for system administration RS485 RS485 RS485 Internet based application 1 Reservation Web server 2 Reservation Web Browser MS Internet Explorer 3 Reservation InfoPoint IP81 1 4 Security Manager 28 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 10 Wireless communication G It is possible to use wireless communication radio network in the SiPass Entro This can be applied between a RF based battery driven Codoor unit RF30 EM and the Segment controller SR35i Up to 512 wireless door environments can exist in the same system together with up to 512 wired doors One SR35i can manage both wired and wireless doors Please refer to the product information for the RF30 EM to see the requirements E g Scandinavian style of lock cases The Wireless Installation manual describes further how to install the wireless application 3 11 Reservation SiPass Entro includes reservation functions e g in sports arenas tennis courts conference rooms etc and works together with the integrated access control system The System Administrator sets which objects such as card readers doors are to
117. s_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure for reservation 26 13 1 Prerequisites for confirmations The Reservation system uses Internet connections that allow for making reservations on any PC The prerequisite for this is that the SR35i controller has an available Internet connection In addition to this you can configure some parameters which allow for sending a confirmation by e mail to the person doing the reservation i The following parameters are defined in consultation with the IT manager Proceed as follows 1 Open the Installer gt 76 application 2 Click the Controllers tab 3 Mark the controllers which contains the CF8 and will send the e mail message and click on Edit 4 Click the Network tab and check enter the IP address to the Domain Name Server DNS This is in fact a server converting the domain name e g xyz com into a valid IP address The DNS often resides with the contracted Internet Service Provider ISP or in the local area network 5 Enter the SMTP Server which is the e mail server handling the outgoing mails This often resides with the contracted Internet Service Provider ISP The name may look like smtpserver swip net or similar 6 Enter the Identity that SR35i uses to create a valid sender address May be e g xyz com and is often used by the ISP to further validate the sender Click OK 8 Finally check that each person h
118. sabled Recommendation The modem should have Watchdog built in Watchdog resets the modem automatically in case of an interrupted connection or power failure i If the modem runs on 12 24V it can be powered by the system s supply in which case it will also make use of the system s battery backup 62 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Installing modem based systems 11 5 Transferring the new system s information to the central PC Go to the PC to be used for configuring and monitoring both systems If this PC has not the SiPass Entro installed install it from the CD Then you will need to create an initial connection in the PC to the modem to be able to transfer the information Later on you only have to select which system connection login and dial up as usual 1 Open the Installer gt 76 application gt Note that if the PC has no system installed the wizard starts automatically and you start the wizard directly without login Go to tab New connection and start the wizard Select Existing system and proceed Mark the modem choice and enter the telephone number of the modem gt Now the connection is set up and you might continue dialling up the remote site as below or later you can log in and dial up Enter the Site name and System name It is very important that you enter the same system name as when you inst
119. sas tectentia scat tara tet node utara E E oe a 110 26 12 Setup for debit fUNCUOM ainsi case suse postada Aa a a ana 111 26 13 Configure for e mail confirmations ccccccseeeeeeeeeeeeeeaeeeeeaeeeeeeeaeeeeesaaeess 111 26 13 1 Prerequisites for confirmations cece ecccceecceceeececaeeeeeeeeeeeeeees 112 26 13 2 Editing text in the CONfIrMATIONS c cc ceececseeeeeeeeeeeeeeueeeeesaeeeees 113 26 13 35 Exalmple of COnfirmMation ieii eon an a ees Rete eerste 113 26 13 3 1 Table of e mail fields in reservation confirmations 00008 114 20 13 39 2 SpeClal mail MEIGS saion a ioioee 114 27 J MAINTENANCE aortna aE 115 27 1 Expanding and modifying the system ccccccccsseeeeeeseeeeeeeeeesaeeeeesaaeeees 115 2 R TO a E ease E E see area ee eee 115 2a NEWOFKIRO aanren a E a E N 115 27 4 Software update in existing SYStEM cccccccseeceeceeeeeeseeeeeeseeeeeeaeeeeesaeeeees 116 27 5 Installing an additional or replacing a PC ceccccceeceeeeeeeeeeeeeeeeeaeeeeens 117 27 5 1 Prepare the database in the existing PC cceceesseeeeeeeeeeees 117 27 5 2 Configure the additional or replaced PC ccccceeeeeeeeeeeeeees 118 Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 27 6 Installing an additional or replacing a SR351 ec ceeccecseeeeeeeeeeeeeeeees 118 2 f Installing more rE
120. sed for more information about the actual unit As soon as the device list is configured it is possible to connect Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Install DVRs 13 7 2 CX Parameters The DVR does not have any front panel buttons to re configure e g its network settings locally Therefore it is recommended to initially use a PC with the SX CX Config software installed without any other network connected and connect the network cables only to the DVR As soon as the steps according to the DVR manual are done you then confirm or re configure the use of and note down the following parameters in the CX type of DVR using the SX CX Config program Parameter Default value Optional User Value Comment User name admin Entro parameter Password admin Entro parameter IP address 169 254 16 9 Entro parameter Subnet mask 255 255 0 0 Entro parameter Gateway 0 0 0 0 Entro parameter Port 12050 N A lt Fixed in Entro gt Port SR lt gt DVR 12050 N A lt Fixed in Entro gt Camera no s and lt Not set gt Entro parameter names i It is a good idea to name the cameras equally in both the DVR and the SiPass Entro environment because otherwise it is a risk that the on screen name differs from the name seen in the SiPass Entro event log When the parameters are configured enter them into the SiPass Entro
121. short times and the other with longer 3 Click OK and repeat for each camera lf you want to change anything just click Edit gt You have now made the settings needed to have images transferred from the DVR to SiPass Entro for viewing 13 5 SISTORE MX There are some initial steps to carry out via the SISTORE MX software before any SiPass Entro software can communicate 68 Normally you probably install the whole MX software suite to be able to both control the detailed settings of the MX DVR as well as viewing It is however possible to only install the RemoteView module to view recordings from SiPass Entro We recommend that the MX software is installed on the C drive Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Install DVRs 13 5 1 MX Parameters You must confirm or re configure the use of and note down the following parameters in the MX type of DVR Parameter Default value Optional User Comment Value User name Administrator Entro parameter Password Administrator Entro parameter IP address lt Not set gt Entro parameter Port 40 N A lt Fixed in Entro gt Port SR lt gt DVR 8080 N A lt Fixed in Entro gt Port range 1100 1109 N A lt Fixed in Entro gt Camera no s and names lt Not set gt Entro parameter il It is a good idea to name the cameras equally in both the DVR and the Si
122. splayed as 1 Change the name of it before going further To get the Segment Controller to store events you have to create a correct connection for each computer When this is done the SR35i will know any time you logon which PC to receive and store events from Proceed as follows 1 Go to the tab Connections in the Installer program and click New 2 A wizard starts and you select SiPass Entro System administration and click Next 3 Enter a name of the connection which SR35i which license number and the communication method 4 Finish Repeat for every computer to be connected You have now created correct connections between PCs and the SiPass Entro system 6 Proceed to make all the necessary settings for the installed SiPass Entro units i We also recommend that you also create System Users to be able to manage the event filters storing places and automatic logoff in a more flexible way 58 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Installing modem based systems 11 Installing modem based systems Up to 10 000 SiPass Entro systems may be controlled from one PC If several systems are to be connected directly to a PC the PC must have as many COM ports as there are SiPass Entro systems PCs communicating with one system directly and with another via modem must have one COM port for connection of a segment controller and another fo
123. ss Entro Door monitor with some optional command options 31 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 13 Integrating with external applications BAPSI 3 13 1 General Normally access control system software is quite proprietary to its system components and is seldom open for customized applications This is quite natural because it is also a security system to be used for controlling e g access to doors in different kind of facilities SiPass Entro can use a well defined configuring interface to communicate with other external software packages like Time amp Attendance Alarm control or similar E g to import export cards get time stamps or events An ordinary TCP IP link is used for transferring the data between the different software components The external software must be modified completed according to the specification we call BAPSI Remember this not a program just guidelines to the programming interface With BAPSI this is done in a specified and safe encrypted way that still keeps the access control system on a secure and integral level The specification can be requested from Siemens Building Technologies 3 13 2 What is BAPSI used for Normally the User interface in access control software allows for functions like card registering time schedule configuring and standard event logging and searching Usi
124. ss control systems there are some kind of centralized power supplies such as battery backup When using these methods it is very important that there is a large enough area of cable We recommend an area of at least 1 0 mm This will exclude data cables such as ELAKY Belden CAT 5 CAT 6 CAT 7 etc as they have areas around 0 1 0 2 mm and will not fit the purpose of a power supply A popular cable is the combi cable which is a PAARFLEX with 2 x 1 5 mm also with a pair 2 x 0 5 mm aimed for data communication See more about Power supplies gt 38 for advice on how to plan the cable network 4 2 2 Cable for RS485 36 Between SR35is and door environments cable should be specified for RS485 It is important that the cable is screened and twisted In both cases the maximum length is 1 200 m If each SR35i is powered by its own power supply only a simple data communication cable between them is sufficient E g the combi cable ELAKY Belden or similar However if two SR35is are to be powered from the same supply another pair of cables are needed The combi cable is sufficient It is also available with two pairs of communication wires Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 System requirements 4 2 3 Cable for network TCP IP 4 2 4 Cable to PC If LAN is used as a communication between a PC and a SR35i or bet
125. storing of images in the DVR unit no recordings are stored in the PC E g cana door alert start a recording during night time only by creating a suitable SiPass Entro time schedule and tie a time zone e g Other time to the filter settings together with pre and post recording times how long the recording lasts before and after the event Continuously recording by time zones You can use a SiPass Entro time schedule to control a continuous recording from a camera but that may generate large files on the DVR 13 4 Camera settings As soon as a DVR has been configured in the Installer program there will be another tab Cameras where each camera must be configured Proceed like this 1 Go to the tab Cameras in the Installer program All cameras that are not configured in the database will be displayed as lt DVRNAME gt lt CAMERAINDEX gt This might however take some time Select a camera and click Edit Or click New for manually adding a camera 3 Change the Name of the camera The DVR that stores the images and the index number will normally be defined by software However if the camera were added manually these parameters must be set 4 Select or create a time schedule for this camera This could be any of the SiPass Entro time schedules 5 Two main starting criteria can then be used By default the parameters configured in the DVR itself will be used for recordings Typically the frame rate and resolution bu
126. supply such as a 24V in the middle you gain a better balance in the load and a better margin can be achieved 24 V DC Typical power supply section 24V 5 5 Several DC power supplies in the same cable section Sometimes one power supply is not enough for securing power to all units in the same system section that a SR35i controls If several power supplies are to be in Stalled the minus negative wire must be tied between them This is similar to using local power supplies described in earlier chapters If this is ignored the data communication RS485 to from door environments may be risked because the minus is used as a reference 24V DC 24V DC X LI X D E Ho SR35i l l 1 1 E Several power supplies in same cable section 5 _ DC12 PR500 with lock strike 2 Must remain used as a reference for data communication 41 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Special installations 6 Special installations 6 1 Anti pass back using BCLINK readers 42 When BCLINK readers are installed for anti pass back function a sub addressing technique is used This means that e g in a P
127. switch are set to VGA VGA monitor output does not exist for every AX it depends on the model You also install the supplied PC software for remote control of the AX in the actual PC where SiPass Entro is installed Otherwise no views will be displayed Although you will see the AX Admin AX Watch and AX Search software commands in the PC you should be careful using them when the SiPass Entro application is running In RAS v3 5 and above the separate applications AX Admin AX Watch AX Search are integrated into one user interface RAS v3 5 has higher requirements regarding system performance please refer to DVR documentation Previous RAS versions are not supported any longer A schedule has to be created and in use with the following characteristics Day All Range 00 00 24 00 Mode Event Channels All connected cameras Make sure that Schedule on is activated in the Recording menu 13 6 3 AX4 and AX Lite 70 Quick setup should be disabled Time Lapse Recording must be set to Off Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 13 6 4 AX Parameters Install DVRs You must confirm or re configure the use of and note down the following parameters in the AX type of DVR It is possible to use the buttons on the AX front panel to configure the basic parameters e g the IP parameters according to the AX Quick start
128. t also pre and post recording time values Depending of the DVR in use the SiPass Entro software then has different capability to control parameters of the DVR See the table below for details of where to set values Value to set AX MX CX Pre recording Same in DVR and In SiPass Entro Only in DVR See SISTORE value in SiPass Entro CX gt 72 67 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Install DVRs Value to set AX MX CX Post recording value In SiPass Entro In SiPass Entro Only in DVR See SISTORE CX gt 72 1 If any continuous recording shall be used choose which time zones to actually have the camera recording Be very careful because this function can generate very large files on the DVR hard disc and do the following By filtered triggering Click on the tabs Recording set 1 and or Recording set 2 Select or create an event filter to trigger and start a camera recording By default all event types as well as doors are disabled Mark any events in the first tab and doors in the second tab Select during which times zones you want to monitor events using the filter Configure different pre and post recording times for each Note that possibilities to change these can differ depending of the models used In this way you can e g have one set with very
129. t controller connected to the actual PC have the same information as the PC Note that in some circumstances like upgrading larger import of persons etc there could be a delay in the transferring of information from the first controller to the next Please study the display information in each SR35i for the correct status information DE OUT OF DATE If the text DB OUT OF DATE and a red indicator are displayed the segment controllers do not have the same information as the PC Note that a certain amount of time may pass before the information has reached all segment controllers and that the system has to be ON LINE for this to be possible You can also look at the status bar to see how far the transferring of data to the PC has gone Normally it might be events that are transferred in cases where the PC has been OFF LINE Retrieving events TTT The default setting is that you will automatically be logged out of the system if no task is performed within 15 minutes In the Entro application you may set the desired number of minutes or disable Indicators in the Microsoft Windows toolbar In the bottom right of the window task bar the following symbol is displayed mle on ae er Wy h 7a es a 10 27 Entro icon in the Windows notification area igs Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Start the software G 7
130. tab IOR6 Inputs ao aN SS Open the Entro application to select further options like Time s schedule and unlocking time 93 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Configure OR6 relay controller 23 4 Power failure warning input Inputs can be setup to monitor signals from power supplies Often used when a battery backup power supply is installed E g a signal can be sent from the PSU when the mains falls and batteries are used Proceed as follows 1 2 3 4 5 Open the Installer gt 76 application Choose tab Doors and mark an IOR6 Click Edit Click the tab IOR6 Inputs Click the list box and choose Power failure 23 5 Emergency opening input An input can activate a function to set selected doors unlocked Proceed as follows Oe oe INP Open the Installer gt 76 application Choose tab Doors and mark an IOR6 Click Edit Select Emergency opening Click on the button to the right of the list box gt A new window with a door list is displayed Select doors that should be unlocked when the input is activated 23 6 Exit button input It is possible to set an input to activate a relay at a certain time E g using a remotely open reservation door or allow for pushing a button in lift Proceed as follows 1 94 2 3 4 5 Open the Installer gt 76 application Choose tab Doors and mark an IOR6 Click
131. te of the system name If the PC has to be replaced you must enter the same system name once again Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Installing modem based systems 7 Exit the wizard by clicking Finish gt Now the Installers main window is displayed 8 You perform the set up of doors etc when you are on site according to the instructions given in the User manual Instead of later on via the modem connection gt Now the main configuring is done and you now prepare to connect the modem 9 In Installer click on the Connection tab 10 Mark the tick box Modem and a new tab is displayed 11 Enter the modem telephone number 12 A suggestion for the modem s so called init string is automatically displayed in the Init string for SR35i modem field This string means command echo disabled auto answer off and DTR disconnected The string can be modified if needed 13 If the modem needs to be able to call the PC enter the desired telephone number in the Telephone number to PC field 14 If the modem needs to be able to call the PC you enter the name of the System user who shall dial up the PC so that the PC knows where to store the events Set also for which circumstances The following alternatives exist After desired number events Means that the segment controller calls the PC following the desired number of eve
132. tems to DC22 44 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Special installations 6 4 Connecting Alarm Status Feedback in DC22 ASF When the DC22 is used to synchronize SiPass Entro and an external intrusion controller a feedback signal fromm the intrusion system can be used Depending on the status of the signal the SiPass Entro recognize the intrusion system as activated or deactivated and perform relevant operations as e g blocking or locking doors The connection between the systems can be done in two ways With a voltage signal With closing signal voltage free Below drawings shows the different methods which both controls the input ASF With voltage signal In this case the intrusion controller must send a voltage signal maximum 24VDC and a minus reference must be available DC22 STATUS Voltage controlled ASF With closing signal The intrusion controller makes the closing Note that a jumper has to be installed in the DC22 between 35 amp 37 DC22 STATUS SZ ASF TL RED 7 LED a ALARM BUTTON Closing signal ASF 45 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Quick start guide 7 Quick start guide Although SiPass Entro includes many different functions to fulfil different customer requirements the steps to form a basic
133. the CD is loaded Otherwise proceed like this 1 Goto the Windows gt Start menu gt Control panel 2 Double click the Add Remove Programs icon 3 Click Install 4 Insert the CD in the CD ROM drive and click Next gt Follow the instructions on the screen Dependent if the system is new or not different steps are performed to achieve the final solution E g if it is the 1st or 2nd PC exchange of PC expansion with more SR35i etc the Installer program is used in different ways Sometimes you have to know the system name as well as the user name amp password to be able to use the software We use a wizard to create the initial communication link to a SR35i controller 10 1 Creating a basic database and connection G The first time you open the Installer application there is no database or information about any connection to use in the PC Therefore a wizard starts requesting the necessary parameters Depending of the selections made some of them might not be needed Default is that one computer is connected and the tab Connections is not visible in the Installer application If more than one computer shall be used please read the section Multi user environment more PCs gt 58 Proceed like this 1 Go to the Windows gt Start menu 2 Choose Programs gt SiPass Entro gt Installer gt The wizard starts 3 Select new or existing system New No system is configured yet and requires a Site name and
134. the list box for each relay and activate them 11 Click OK 12 Click the tab Doors and mark the terminal intended as a Master for the IOR6 13 Click on Edit and click the tab Lift Control and mark the IOR6 units that will be controlled by this terminal 14 Click OK A suitable name for the master door terminal is e g Lift floor Door terminals are named on the Doors tab In the Entro application the numbered floors relays are shown on the Access groups tab in the door list under the name of the master reader This way it is very easy to select the floors to which the group should have access It is also possible to activate the relays according to the time schedule applied for the actual master reader You find the set up for this in the IOR tab in the Door menu in the Entro application You mark the tick boxes in the time zone column for the relay to be activated Relay 1 4 in every IOR6 can also be activated via a signal to exit button input remote opening Building Technologies Fire Safety amp Security Products 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en 10 03 2010 Contigure Intrusion Alarm zones 24 Configure Intrusion Alarm zones siPass Entro offers different methods to arm a bistable intrusion alarm zone Using a valid card at the door terminal Using a pushbutton connected to the Alarm button input Using an external timer connected to the Alarm button input Using a SiPass Entro Al
135. time shift delay is to be applied please read more about setup zones for reservation object gt 104 11 Click OK 23 8 Lift Control with IOR6 When applied to lifts SiPass Entro can be used to restrict access to the different floors in a building For lift control up to 32 IOR6 relay controllers can be connected to the SiPass Entro system which means that altogether 192 floors can be controlled Note that neither IOR6 nor its master reader can be included in zones The lock relay of the master reader door controller cannot be used for any applications 1 Open the Installer gt 76 application 2 Click the Door tab Normally a new IOR6 is displayed as Cx Dy in the list of doors Mark this click Edit and step to item 7 below If you manually want to create a new IOR6 proceed as follows 3 Click New The Door properties are displayed 4 Enter the name of the relay controller in the Name field 5 Check and or enter the address 6 Inthe list box Terminal type select IOR6 95 Building Technologies 020_SiPass_Entro_6_5 _A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Configure OR6 relay controller 96 7 Click the IOR6 Relays tab 8 Mark that this IOR6 will be used for lift control Enter name of each relay with digits They will later be shown as the name of the IOR6 the relay number E g if the IOR6 is named Lift A and relay 3 it is shown as Lift A 3 10 Click on
136. transferred directly into every SR35i RS232 is the easiest method to use when the segment controllers are placed in different geographical areas It is important that these get the correct IP address system name and encryption key Every new SR35i is displayed as Cxx Now proceed according to the steps in the section SR35i Configuring gt 86 to set the IP address Proxy and other necessary parameters Configuring via TCP IP In this case the PC communicates with a dedicated SR35i whilst the other controllers will get the information from this one via TCP IP If the system is new you will already have had the opportunity to configure the correct IP address In the Installer program the first SR35i is shown If there are more non configured SR35i they will normally pop up on the screen and be available for use in the actual system Otherwise you have to use the command New to create the rest of 83 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure names for segment controllers Li the controllers and to set the IP address Proxy and other necessary parameters according to the steps the section SR35i Configuring gt 86 Transferring the data to from completely new SR35i will take some minutes due to the load on the network This also applies for updating the Door monitor program Configuring via the keypad in the SR35i In some case
137. ty Products 10 03 2010 Description of equipment 3 3 System capacity and limits SiPass Entro software Software for control of up to 10 000 systems each capable of managing up to 512 wired doors and 512 wireless doors RF in up to sixteen controllers 40 000 cards 240 time schedules 480 access groups 240 zones alarm anti pass back roll call interlock and entrance limitation zones 16 system users in 4 levels installer level 14 holidays 7 half days and 4 holiday periods in each time schedule Reservation functions 64 reservation objects machine groups Maximum of 30 doors and or IOR6 relays in each reservation object 32 time schedules with 24 intervals in each Flexible interval reservation Maximum number of reservations is 6100 Video Surveillance CCTV integration Maximum 16 DVR one DVR per SR35i SR34i Maximum 128 cameras Card printing Multiple card and or receipt template design Bulk printing of cards 13 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 3 4 System components 14 There are different products included in the SiPass Entro range of components e SR35i Segment controllers Up to 16 segment controllers can be connected to the PC in a daisy chain configuration Each segment controller can control 4 wired 4 wireless 8 8 16 16 or 32 32 doors The information you program in th
138. uirements on function and security e g alarm by pass and door control 4 1 DC22 with Magnetic card or proximity readers 2 DC12 with Proximity reader 3 DC12 with Hands Free reader 4 DC12 with proximity reader PP500 with PIN pad in small housing Proximity Codoor PD30 EM PD40 EM Electromechanical unit equipped with a proximity reader for EM technology Connects to the Segment controllers PD30 EM fits primary Scandinavian lock cases and PD40 EM the Euro standard Radio link RF Codoor RF30 EM Communicates wireless to the Segment controllers directly or via RFQ routers dea RF9 Wireless router used for amplifying and routing the RF signal Door controllers without remote terminals In some cases there is a need for monitoring or opening a door by time schedule The DC01 can be used as a timer controlled relay or monitoring unit B Door controller DC01 15 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Description of equipment 16 Relay controller To control e g a lift the IOR6 can be used Any reader can control which relays to activate The IOR6 can be used in reservation applications Version 5 onwards also offers functions like Common alarm Lift control emergency opening and power failure monitoring Relay controller IOR6 CF8 If Reservation is to
139. utes The buzzer warns people still in the building that the alarm is about to be activated During this time the pre warning alarm relay output will change state in all DC22 included in the actual alarm zone If you decide to not use warning the alarm by pass relay changes its state immediately without any buzzer warning pre warning If the ASF function is enabled the exit button still works until a valid ASF signal occurs This will be the case if the intrusion alarm takes care of the pre warning not yet any ASF Select if the Exit button is allowed to abort the alarm activation cycle Choose which Time Schedule will be used for time controlled alarm activation If you do not select any you have to manually activate it or use an external signal connected to the input for alarm activation If you have not created time schedules in the Entro program you click on the clock icon and select New Edit or Duplicate a time schedule Click Next Mark the tick box Use Alarm Status Feedback if the intrusion alarm s status signal will be connected This signal connects to the ASF in the DC22 It tells SiPass Entro that the Intrusion Alarm has been activated or deactivated In the field Timeout for ASF you write the time in seconds SiPass Entro will wait for the status signal before it is seen as an activation failure In this case SiPass Entro will go back to normal state and accept normal accesses Mark the tick box
140. vate the function 1 Open the Entro gt 76 application 2 Choose on the menu System gt System settings 3 Mark the Enable duress option gt A warning message is displayed 4 Click Yes to activate the duress function 82 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Contigure names for segment controllers 20 Configure names for segment controllers Dependent on how the SR35i s should communicate with each other the parameters are set up in different ways Remember that the basic parameters like the IP address initially can be set by using the integrated keypad in each SR35i This means that you fulfil the requirements for communicating with the PC but configure the rest of the settings in the Installer application If you intend to use dynamic IP addressing for segment controllers you should read more about preparing network gt 49 If a modem will be used please refer to the section Installing modem based systems gt 59 for more information 20 1 Create multiple SR35i for TCP IP communication Address 1 Address 2 g g C E SR35I SR35i X 4 1 TCP IP i TCP IP l TCP IP TCP IP d E LZ a SR35i Address 3 In this case three methods can be used to set up the SR35i segment controllers Configuring via RS232 A PC is connected to every SR35i via RS232 connection The information is
141. wa 4 Enter in password the password field default pass 5 If several systems exist select one system gt If more than 20 systems exist there will be an additional search field 6 Enter a character gt The system finds any name that includes this Click OK gt The SiPass Entro main window is displayed Start applications via the icons It is possible so quickly start an Entro application by using the icon Proceed like this 1 Position the cursor over the icons and right click gt A menu is displayed 2 Select SiPass Entro or Door Monitor gt Either of the applications is started Note that the Installer application must be started via Windows start 76 Building Technologies 020_SiPass_Entro_6_5 A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Start the software 16 1 Indicators for communication status Indicators in the application windows In the bottom right of the box there are two indicators ON LINE If the text ON LINE and a green indicator are displayed the PC and the SiPass Entro application are connected to the access control system OFF LINE If the text OFF LINE and a red indicator are displayed SiPass Entro has no contact with readers and controllers This means that the information registered in the PC does not reach the segment controllers DB UP TO DATE If the text DB UP TO DATE DB database and a green indicator are displayed the segmen
142. ween SR35i some existing LAN cable will suffice Cat 5 cable specified for 10 100 Mbit is mandatory Note that the SR35i have an integrated network switch with two external connections and one internal for SR35i This means that you can use a standard network cable without any hub direct to PC and or local area network Whether new or old cables are used the customers IT manager must be consulted when specifying or commissioning up the system Between the SR35i and the COM port on the PC a straight RS232 cable is used For LAN use a common standard LAN cable Cat 5 Ethernet 4 2 5 Earthing and screening for RS485 The cable screens on each circuit must be connected to protective earth but only in one place in the system see diagram Also remember that metal parts in doors or vehicle barriers can be in contact with earth For readers installed on these surfaces the screen must not be connected to the metalwork Avoid placing the cables close to heavy current installations e g lifts and power doors since they may cause disturbance SR35i Connection of screen 1 Global bus 2 Local bus 37 Building Technologies 020_SiPass_Entro_6_5_A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Power supplies 5 Power supplies 5 1 Central DC power supply 38 Central power supplies ar
143. work settings for LAN connection The PC must have a valid crypto key installed if used If this has been changed from the default factory it must be documented and available It is recommended that a new PC does not have any old SiPass Entro software or databases installed etc If the PC where SiPass Entro runs is about to be replaced e g upgrade to Vista it may be necessary to upgrade the SiPass Entro software as well In these cases where both PC and SiPass Entro is replaced upgraded the SiPass Entro system should be upgraded first and done from the old PC After that PC replacement should take place 2 5 1 Prepare the database in the existing PC Proceed as follows 1 2 Open the Installer gt 76 application on the existing operating PC Go to the Connection tab in System gt System settings and select that several computers can be connected concurrently Click OK gt A new tab appears in the main window in the Installer The default earlier hidden connection is now displayed as 1 Change the name of it before going further by marking the name click Edit and enter a suitable name Click the tab Connections and start the wizard by clicking New Select System administration and enter the parameters Name of the connection any name Which SR35i we recommend using the same SR35i for all PCs unless a serial port RS232 is to be used in the new PC 117 Building Technolog
144. y must also have this setting This guarantees correct time in the system independent of where a SR35i is installed When you configure a SR35i as Proxy it will need to know where to fetch the clock from You can select internal or external However if running the SiPass Entro system in multiple sub networks with Internet connectivity between it s recommended to use an external time server If the clock server function resides in another subnet the port 123 must be open in the router In the menu System gt Entro System time in Installer program are more choices for the system clock Do like this 1 Check that the indicators in the lower right corner of the SiPass Entro windows display ONLINE and DB UP TO DATE gt 77 Click Advanced 3 Select method for time server Internal time server e g SR35i and select controller External time server e g via Internet and enter IP address 4 Select if every SR35i is allowed to correct its time relatively to GMT time 5 If this is selected every segment controller will display a new tab Time where the adjustment value is chosen e g 1 2 etc 6 Exit 7 Check in the menu System gt Entro System time and check the choice of Automatic daylight saving time changes 80 Building Technologies 020_SiPass_Entro_6_5_ A24205 A335 B317_e_en Fire Safety amp Security Products 10 03 2010 Personalize Entro settings 19 Personalize Entro settings 19 1 Card rea

Installation manual

Contents

Download Pdf Manuals

Related Search

Related Contents