IR High Speed Dome Camera Installation Manual
Contents
1. After connecting check and arrange all the wires tie the wires up with girding and fasten on the installing panel by screw Double check it after the installation and set up an electric circuit on the dome camera The dome camera will take a self checking turn 360 degree horizontally and 90 degree vertically to check the electrical and mechanical structure of the camera and the dome After resetting to the basic point the dome camera stops which means a good self checking 8 Steps of Self Installation Stepl Take off the camera front end cover modules Take away the dome camera from the package turn the chip to a suitable angle use the H2 5 Hex wrench in the accessory package to screw out the four screws pull out the connecting wires installed on the front end cover modules and take off front end cover modules As follows w NE a Step2 install the camera Put the camera parallel under the install panel until the camera aims at the middle of the front end cover with a distance of 1 2mm and then align the four holes on installation panel and camera make sure the 22 image is in right direction and then lock the screw M2X4 screw As follows Step3 install the front end cover modules Install the connecting wire to proper place in the front end cover modules and connect the FPC cable with the camera base lock the screw between front end cover modules and the chip after checking finally turn the d2. crash protection 13 steel wire rope Hold the camera in both hand and in the angle of 45 as below figure align the dome camera cover rotate pendant to bracket rotate hook as fig 5 8 Crash protection STE Wire rope Rotate pendant and hook installation sketch RE Fig 5 8 Connect installation head and dome camera 7 Connect the terminals of dome camera integrated connection line with the socket on the top of camera 8 After confirmation hold the camera in both hand follow the direction of arrow and rotate to vertical angle then fix the three M5X19 screws as fig 5 9 by hexagon wrench 3 Screws Fig 5 9 Fix screws and finish installation Attention glass is easy to get scratch please take off the protective film after the installation is completed 14 6 Hoisting bracket installation process A d D wv lt r 9 9 x D2276 _ Fig 6 1 Hoisting sketch Method 1 l Select a suitable place for installation and punch on the surface bracket dimension as fig 6 2 d D 2 0 Equispaced EE pes 200 or other customize length D Fig 6 2 Hoisting bracket dimension 2 Insert the dome camera integrated connection line to the inside of bracket as fig 6 3 15 Fig 6 3 Connect installation head and hoisting bracket 3 Fix the dome camera installation head to bracke
3. to avoid the voltage shortage caused by transmission line In order to avoid voltage shortage caused by transmission line and then the abnormal of dome camera when implement wiring wire diameter should not smaller then 1 millimetre power lines not longer than 2 meters and the connector should be welded with soldering tin 5 Wall mounting bracket installation procedure Attention bracket is optional part m See _ 334 2 Fig 5 1 Wall mounting sketch 10 Method 1 1 Select a suitable place for installation and punch on the surface bracket dimension as fig 5 2 4 910 e i ty EV CT C oO SO a ANA NS A 98 30 Fig 5 2 Wall mounting bracket dimension 2 Passthe dome camera integrated line through bracket as fig 5 3 eee ES aan Wall mounting bracket e Dome camera integrated connection line Dome camera installation head Fig 5 3 Fix wall mounting bracket Attention when the line is out of the bracket please make it downward first as fig 5 4 after that if necessary you can make it upwards this can prevent water inflow to the inside of device 11 Fig 5 4 Pay attention to waterproof when wiring 3 Insert swell screw into the punched hole aligning the hole on the base of
4. 3 A Earthing rod z UPS L Earthing rod em e cum o t Into earth 1 5 meters Into earth 1 5 meters Fig 2 3 Anti thunder grounded that has installed lightning rod Attention if optical transceiver or anti thunder or related middleware is used during the process of dome camera transmission it should ensure the middlewares are well grounded as well as when camera connection cable go through middlewares 3 Installation Environment Table 1 Installation Environment AC 100 240V INPUT 50 60Hz 1 5A Max Working Output DC 15V 4 0A Environment COURT 24W Chigh light IR lamp on Anti interference anti thunder Humiture Working outdoors 30 C 60 C temperature Relative humidity lt 90 no condense This product is equipped with standard power it can be only install in indoors watertight caisson or put into A bracket in the installation box it should fix the power to avoid gliding It can t be exposed in outdoors or may cause water inflow or burnout The installation area should be solid it should not broken delaminating or has related phenomenon it also should bear 5 times or above weight of dome camera and bracket to avoid image shaking or camera falling 4 Prepare for cable There are some resistances exist in common power lines when transmit voltage there will be some lost the longer the power line is and the smaller the wire diameter is the heavier lost it will cause In order
5. 7 45 as fig 6 7 align the dome camera cover rotate pendant to bracket rotate hook Bracket rotate hook Dome camera cover rotate pendan Crash protection steel wire rope Dome camera Rotate pendant and hook installation sketch Fig 6 7 Connect IR installation head and dome camera 6 Connect the terminals of dome camera integrated connection line with the socket on the top of camera After confirmation hold the camera in both hand follow the direction of arrow and rotate to vertical angle then fix the three M5X19 screws as fig 5 9 by hexagon wrench as fig 6 8 3 Screws i o E m Fa I t TENE EY Fig 6 8 Fix screws and finish installation Attention there should not be holes or craze in the suspension bracket connecting pole to avoid water inflow 18 1 Cable connection Camera external wiring Dome camera integrated connection line is divided to simple and enhance mode detail configuration is as below table Enhance mode Integrated line interface simple mode Power connectionline o o e e RS485 connection line ee ee ee Video cable BNC output Grounded termina 1 Alarm interface Lem qw Remark e represents for have represents for do not have Below will take enhance mode for instance Dome Power connection Dome camera camera line power adapter power Dome M camera cR E Green A White B connection line cw co
6. IR High Speed Dome Camera Installation Manual Read the user manual carefully before using this product O COON MM OP cor Table of Content MOIetDEOO I eset cha panacea ritieni daba nidis nim so edu deside 3 Anti static anti interference anti thunder anti surge 5 Installation Evironment s eee ooi Toto eoe St eos 9 Prepare LO CAO Coc eso ooo toto tete eei b i lb eds 10 Wall mounting bracket installation procedure 10 Hoisting bracket installation process cccssssecceccceeceeeeeeeeeeeeeeens 15 Cable conneCion incu eae anaes 19 Steps or sell T stallatiOD sio doses acre c o ero di Eni b c eet 22 Glass C l antmi oed ie oo m e oot ee ente tni eed n 24 Waterproof Attention 1 It s recommended to use wall mounting bracket which arm bracket is upward in certain angle for outdoor installation 2 It s not allowed to use hoisting bracket and horizontal wall bracket for outdoor installation which will cause water inflow to camera 3 For User self selected brackets it s recommended to use those with internal thread connector it should also ensure the waterproof performance of the brackets If use external thread bracket for user self selected bracket it should ensure the waterproof performance of switching components that connect bracket and camera 4 When install the camera thread connector should be bound with PTFE tape also it should ensure t
7. alarm function unless alarm trigger is released or being close manually 3 When the alarm function is open the input ends that haven t connect with alarm probe should be connected with 2 2K resistance or the dome camera system will recognize as there is alarm signal to trigger input and start alarm function 20 Sketch map of the alarming input connecting of the normally closed probe 2 2K Resistance ALM 1 ALM 3 ALM 4 ALM 2 When the first alarm is activated call the fixed No 1 preset position When the second alarm is activated call the fixed No 1 preset position When the third alarm is activated call the fixed No 1 preset position When the fourth alarm is activated call the fixed No 1 preset position Alam can only be activated when preset position 1 2 34 are finished setting in advance ALM 4 ALM 3 ALM 2 ALM 1 GND Sketch map of the alarming input connecting of the normally open probe ALM 1 ALM 2 ALM 3 ALM 4 When the first alarm is activated call the fixed No 1 preset position When the second alarm is activated call the fixed No 1 preset position When the third alarm is activated call the fixed No 1 preset position When the fourth alarm is activated call the fixed No 1 preset position ri cA 5 Alam can only be activated when preset position 1 2 34 are finished setting in advance 21 Sketch map of the alarming output connecting P 1 way alarm output O O zZ C
8. bracket and the hole on the installation surface insert screw and lock it 4 Fix the dome camera installation head to bracket screw 4 M6x12 screws by cross screwdriver as fig 5 5 M6xlemm Fig 5 5 Fix the dome camera installation head to bracket 5 Connect the camera and wall mounting bracket by crash protection 12 steel wire rope then hold the camera and fix the bracket to wall as fig 5 6 Fig 5 6 Fix the screws and finish installation Method 2 l Select a suitable place for installation and punch a hole on the surface bracket dimension as fig 5 2 2 Screw off the three M5X19 screws in installation head and body position as fig 5 9 open the installation head and take off cables 3 Fix the installation head that with dome camera integrated 5 connection line to wall mounting bracket pass the connection line through bracket move the installation head in the direction of the arrow until it reaches the bracket then fix 4 M6X12 screws as fig 5 7 Screw M6X12 IR installation head Dome camera integrated FEET NN connection line Fig 5 7 Connect the installation head and wall mounting bracket Insert swell screw into the punched hole aligning the hole on the base of bracket and the hole on the installation surface insert screw and lock it Connect the camera and wall mounting bracket by
9. he thread is sealed In rainy and moist area it s suggested to apply waterproof paint in seaming places after installation v Wall mounting Bracket For outdoor installation it should use wall mounting bracket which arm bracket is upward in certain angle which can enable the camera not so easy to have water inflow As below figure for outdoor installation wall mounting bracket can be used cooperatively with hug pillar type bracket and corner type bracket Dome camera installation part should be the highest point of the bracket after installation l NSA a a ARRAS Fig 1 1 suit for outdoor wall mounting bracket Horizontal arm bracket Arm bracket slope down Fig 1 2 not suit for outdoor wall mounting bracket v Hoisting bracket Hoisting bracket is not suitable for outdoors as there is gap between hoisting bracket and fix hanger plate it is easy to have water inflow in outdoors even if apply glass cement or bind with electrical tape can not perfectly solve the problem of waterproof As fig 1 3 Fig 1 3 Hoisting bracket v Use client customized bracket If use for outdoors client customized bracket should be upward in certain angle can not use arm bracket that slope down or horizontal and there should not be opening or flaw on the bracket as figl 4 There should not be openning There should not be openning or fla
10. nside of steel tube and ground to the earth local control center normal grounded is ok Control center 9 S 7 EH Keyboard Earthing rod NVR Monitoring platform Earthing rod Grounded wire resistance lt 4 l Earthing rod Steel tube protection l l Working platform l earthing rod Into earth 1 5 meters Into earth 1 5 meters Fig 2 1 Insulation stand pole or wall anti thunder grounded v Metal pole grounded Metal pole method adopts go through PVC pipe grounded For metal pole that hasn t installed lightning rod the ground lead go through PVC pipe get close to metal pole fixt the position and implement grounded as fig 2 2 Control center ZZ f i Display Keyboard Earthing rod NVR Monitoring platform Earthing rod LIN Grounded wire resistance lt 4Q Metal pole UPS z Earthing rod PVC 4 A Pipe cover Working platform earthing rod Into earth 1 5 meters Into earth 1 5 meters Fig 2 2 Anti thunder grounded that hasn t installed lightning rod For metal pole that has installed lightning rod the ground lead goes through the inside of metal pole go through PVC pipe and then grounded and PVC pipe should keep enough distance from the inwall of metal pole as fig 2 3 Lightning rod ome camera Control center Keyboard Earthing rod should be installed IT in 30 field under IB Pte lightning rod NV R Monitoring platform
11. ntrol device Video cable Video signal ee BNC connection head monitor device Power supply interface Grounded Anti thunder Earth dome Brown line terminal erounded camera Black alarm input public end Yellow the first way Sensor tieksi alarm input Green the 5 cores cable Alarm input EA second way alarm input Blue the third way alarm input White the fourth way alarm input 19 Brown alarm output High speed dome public end ABOTeSeRDI GEIL uuu camera alarm bell Gray alarm continuous open output end The positive and negative polarity of RS485 can not be wrong connected A RS485 positive B RS485 negative Wrong connected can not control dome camera 7 0 Alarm input output line connection and installation Alarm input output line connection and installation can refer to below sketch when the alarm function is open and dome camera has distinguished alarm signal then can response output alarm signal if alarm linkage preset position is set in advanced then dome camera will call this position Attention 1 Alarm input should be switch type input signal any other type signal such as voltage signal and so on may cause damage to the dome camera When there are alarm input for several channels dome camera will give cycle response to each channel one by one the monitor default time for each alarm channel is 3 seconds 2 So long as there is alarm signal trigger input dome camera will prior execute
12. ome camera to vertical angle As follows Special notice The seal ring should keep smooth with the interface of front end cover not hunched The edge of the seal ring should completely cover the front end cover and the screw must be locked to make sure a good sealing up and avoid leaking which may damage the camera and the electric circuit As follows Totally installed seal ring 9 Glass Cleaning Notice of glass cleaning 1 Clean the glass regularly could ensure the clear image of the dome camera 2 Avoid touching the glass directly by hand or skin which may probably make bad influence to the image 3 Please use a soft dry cloth or other substitutes to clean the surface hard object may cause indistinct image 4 Using glass cleaner to remove any stubborn dirt 24
13. t screw 3 M6x12 screws as fig 6 6 4 Insert swell screw into the punched hole align the hole on the base of bracket and the hole on the installation surface insert screw and lock it e Moxlemm Fig 6 4 Connect IR installation head and dome camera 5 Connect the camera and wall mounting bracket by crash protection steel wire rope then hold the camera and fix the bracket to wall 16 Fig 6 5 Fix screws and finish installation Method 2 l d Select a suitable place for installation and punch on the surface bracket dimension as fig 6 2 Screw off the three M5X19 screws as fig 6 8 in installation head and body open the installation head and take off cables Fix the installation head that with dome camera integrated connection line to wall mounting bracket pass the connection line through bracket move the installation head in the direction of the arrow until it reaches the bracket then fix 3 M6X12 screws as fig 6 6 Hoiting bracket Screw Mex dz IR installation head Dame camera integrated connection line Fig 6 6 Connect installation head and hoisting bracket Insert swell screw into the punched hole align the hole on the base of bracket and the hole on the installation surface insert screw and lock it Connect the camera and wall mounting bracket by Anti falling steel wire rope hold the camera in both hand and in the angle of 1
14. tion level it should be implemented individually construct anti thunder project directly for outdoor work pay attention to the construction skill can reduce the damage from lightning and etc l 2 3 Signal transmission line should keep 50 meters distance from high voltage devices or high voltage cable It s better to routing under eave for outdoor wiring In open area the wiring should adopts seal steel tube underground method and one point grounded to the steel tube it s forbidden to wiring overhead In strong thunderstorm or high voltage area such as high voltage converting station it should adopt high power anti thunder devices and install lightning rod and so on The anti thunder and grounded design for outdoor device and lines should suits for related national and industry standard Grounded device should satisfy the system requirements for both anti interference and electric safety and it can not shorting or hybrid junction with strong power grid zero line When the system grounded individually impedance ground lt 4Q grounded wire sectional area should gt 25mm2 Dome camera anti thunder grounded line adopts several copper cable that sectional area gt 4mm wire diameter about gt 2 3mm take below figure for reference to implement grounded 6 V Cement grounded Cement method should configure with steel tube protection jacket for grounded line poling as figure 2 1 dome camera grounded line go through the i
15. w on the bracket arm or flaw in the side of the bracket arm 8 i 3 stand pale Fig 1 4 Customized Bracket Unified bracket arm and stand pole ET There should not be openning or flaw on the bracket arm Fig 1 5 Customized Bracket Attention 1f use horizontal arm bracket then the horizontal arm bracket and the stand pole should be integrated there should not be opening or flaw in the connecting part 2 Anti static anti interference anti thunder anti surge Attention 1 The installation of dome camera should be grounded or it may cause the damage of electronic pieces by static 2 3 In lightning area it should grounded the dome camera to release the high energy and avoid damage In area with unstable voltage it should grounded the dome camera to release the high energy such as surge and avoid the burning of camera power Install anti thunder grounded lead can not take the place of safety grounded lead If use bad grounded stand pole such as wood pole cement pole it should also install safety grounded lead to ensure the camera or stand pole will not cause incident Dome camera anti thunder grounded lead should be grounded individually it can not be grounded by other electronic devices near by Dome camera adopts built in anti thunder technology which can resist the instant indirect lightning strike under 4K V when grounded is well enough To prevent the lightning damage that exceed the built in protec
Download Pdf Manuals
Related Search