Owner/User Manual
Contents
1. Model PRO9556E VT TA Owner s Manual SLT EE SS 3 Channel Remote Car Starter FEATURES 2 Three Button Programmable RF Transmitters Three Channel Receiver capable of accepting 4 transmitters External Superheterodyne Receiver Antenna w PushButton Switch amp LED Keyless Entry Outputs Trunk Release Output On Board Start Relay On Board Accessory Relay On Board Ignition 1 Relay On Board Ignition 2 Relay Ignition 2 Relay Selectable On or Off During Cranking On Board Parking Light Relay Ignition 3 Shock By Pass GM VAT Output relay required Tach Signal Learning Circuit Two and Two Safety Shutdown Circuits Alarm By Pass Output Accessory Outputs Pulse Before amp After Start During Crank amp After Shut Down Selectable Steady or Flashing Parking Lights for Run Indication Selectable 5 10 15 20 45 60 Minute Run Time Selectable Door Lock Output Pulse Timing Car Finder Mode PATENTED www voxxintl com company patents 128 9319 1 of 4 KEYLESS ENTRY The Lock button on the transmitter is used to lock the vehicle s doors The Unlock button is used to unlock the vehicle s doors To lock or unlock the doors simply press and release the desired function button one time As a keyless entry unit for your convenience the parking lights will flash once when the doors are locked and twice when the doors are unlocked REMOTE CAR FINDER The Lock or Unlock bu2. arrive at the vehicle turn the ignition key to the ON position not the spring loaded start position then step on the brake pedal to disengage the remote starter The vehicle will continue to run but now on its own power NOTE The engine will stop running before the pre programmed run cycle has expired if you perform any one of the following functions Press and release Key Trunk button on the keychain transmitter two times within 2 seconds Depress the brake pedal Open the vehicle s hood Place the unit in the safety control disabled mode PUSH BUTTON LED RECEIVER VALET OVERRIDE SAFETY CONTROL SWITCH The Push Button LED switch located in the receiver allows you to temporari disable the remote starting function of the system This is recommended whenever 7 he vehicle is being serviced 128 9319 2of4 To place the system in the service mode 1 With the system disarmed unlocked and the ignition switch off Press and Hold the Push Button found on the windsheild receiver in 2 Turn the ignition switch on off on off on off 3 The LED begins to flash two short flashes followed by one long flash and continues this pattern until returned to the normal mode of operation This puts the unit into the R S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise To Exit R S Override Mode 1 With the system disarmed Pr
3. ess and Hold the Push Button found on the windsheild receiver in 2 Turn the ignition switch on off on off on off 3 The LED turns off indicating that the R S unit is fully functional once again PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS BANK 1 The Transmitter Model Name 143BPr Is Also Found On The Back Of The Transmitter Case Battery Use CR2032 1 Turn the ignition key to the on position 2 Press and Release the Valet Programming switch 3 times Siren Chirps 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren 4 Turn the ignition switch off The above action programs the Lock Unlock Start Trunk and Option 1 buttons which are typical for most systems For additional channel programming beyond the 1 option button you can use any unused button or combination of buttons not in use In other words to access option channel 5 6 7 you would do the following From step 3 above a Press and Release the Valet Programming button 4 additional times to get to channel 5 then Press any unused transmitter button or button combination to program b From step a Press and Release the Valet Programming button 1 time to get to channel 6 then Press any unused transmitter button or button combination to program c From step b Press and Release the Valet Programming button 1 time to get to channel 7 then Press any unused transmit
4. itter programming guide This reprogram operation will erase all unauthorized or unwanted transmitters Transmitter Battery Replacement 1 Locate and remove the 00 point philips head screw on the back of the transmitter case 2 Carefully separate the front case from the rear 3 Slide the CR2032 battery out from under the battery clip and dispose of properly 4 Install the new battery with the side facing up away from the circuit board 5 Close the case and reassemble in reverse of disassembly FUNCTION SETTING CHART To be completed by installer Run Time Min O Door Lock Timer Sec O Lights Pulse O Steady O FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment To purchase replacement transmitters or to get additional product information go to www pursuitcarsecurity com 2014 Voxx Electro
5. nics Corp 150 Marcus Blvd Hauppauge NY 11788 128 9319 128 9319 4 of 4
6. ter button or button combination to program NOTE Not all systems have channels above 3 check with your installation center for options your system may or may not have This remote has the ability to operate 2 Audiovox Alarms From A Single Transmitter To toggle on and off vehicle one or two Press the Trunk Key button the Lock button for 5 seconds The LED flashes 2 times Release the buttons to select 2nd vehicle mode Program this transmitter into the second vehicle s system Any time you are in 2nd vehicle when the transmitter is operated the LED will flash twice for each function When in the prime vehicle mode the LED will flash once for each function 128 9319 3 of 4 PROGRAMMED TRANSMITTER NOTIFICATION PTN Every time after Disarm when the ignition key is turned on the unit s LED will report the number of transmitters programmed into the system This safety feature will alert you if an unauthorized transmitter has been programmed into your vehicle s security system without your knowledge Typically from the factory there will be 2 flashes and a pause repeated 3 times indicating that two transmitters are programmed into the system If you note additional flashes an additional transmitter may have been added without your knowledge or authorization If you notice a change in the transmitter LED report pattern you can correct this by looking up how to erase and reprogram your transmitters found in the transm
7. ttons are also used to access the car finder mode This feature is particularly useful in a crowded parking lot where finding your car may be difficult To access the car finder mode while within range of your car Simply press and hold either the lock or unlock button of your transmitter for three seconds The parking lights will begin to flash making your vehicle more visible The lights will stop automatica Y after 30 seconds If you wish to turn off the car finder mode prot to the expiration of the 30 socond timer press and release either the lock or unlock button of your transmitter one ime REMOTE TRUNK RELEASE If you have electric trunk release in your vehicle and the remote trunk release option was added to your vehicle simply press and hold the Key Trunk button of your keychain transmitter for 4 seconds or until the electric trunk of your vehicle opens REMOTE STARTING THE VEHICLE This unit will not start the vehicle if any one of the following situations exist The vehicle s hood lid is opened The gear shift selector is not in Park The brake pedal is depressed The safety control switch is in the Off position To start the vehicle press and release the Key Trunk button two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 20 minute run cycle As a visual indication the parking lights will flash or remain on depending on the setting by your installation center When you
Download Pdf Manuals
Related Search