Floor / Pallet Scale - Floor Scales & More DIGIWEIGH
Contents
1. Floor Pallet Scale ore c Screw each foot onto the load cell at each corner of the scale base d Lay down the scale and level it e Connect the cable onto the transmitter f Connect the transmitter with the scale base Floor Pallet Scale _4 g Place the transmitter on the side of the scale h Connect the antenna and place on the side of the scale Turn on the indicator and your scale is ready to use For advanced operations please refer to the following pages Your scale was pre calibrated Re calibration is not necessary However due to change of the environment such as gravity temperature humidity etc the accuracy may be affected For perfect results you can re calibrate the scale Although the indicator comes with wired cable port the scale may not work by connecting the indicator with the scale base using cable Please contact support digiweigh usa com for assistance Floor Pallet Scale 5 2 1 FRONT AND BACK VIEW OF THE INDICATOR ZERO TARE A ZERO Model DWP 102E Front View Back View Floor Pallet Scale 6 2 2 KEY FUNCTIONS UNIT Switch between weighing units FUN Select or enter the function and save the setting values of parameters In counting mode press to view unit weight counts and total weight when F3 Key 1 In the accumulation mode press to view numbers when F3 Key 2 Press to enter exit animal mode when F3 key 52. MOD Enter exit counting mode when in weighing mode when F3 Key 1 Accumulate and print when F3 Key 2 Hold release the readout when F3 Key 3 Enter pre tare value when F3 Key 4 Parameter setting for animal weighing when F3 Key 25 TARE Enter fast calibration when pressed in warming up Tare off the container weight When setting parameters press to change the value ZERO Press to enter parameter setting during warming up Zero the readout When setting parameters press to move the cursor ON OFF T urn on off the scale Floor Pallet Scale si es 3 1 POWER ON AND AUTO ZERO SETTING 3 1 1 The indicator will perform countdown self checking when turned on Then it will enter weighing mode 3 1 2 When powered on if loading weight on the scale deviates from the zero point but still within zero set range the indicator will set zero automatically if it is out of range it is necessary to adjust the zero point or recalibrate or reset 3 1 3 Press UNIT button to select your weighing unit There is indication on the readout panel showing the current weighing mode 3 2 MANUAL ZERO SETTING 3 2 1 In weighing mode you can press Zero anytime to zero the readout 3 2 2 If the displayed value deviates from zero point but still within zero range pressing Zero key is available Otherwise Zero key is invalid In this status please recalibrate or reset zero parameters 3 2 3 Zero function works only whe
3. Floor Pallet Scale DWP 5500RW Floor Scale DWP 102E Indicator User Manual CHAPTER 1 MAIN SPECIFICATION CHAPTER 2 INSTALLATION 2 0 SCALE BASE SET UP 2 1 FRONT AND BACK VIEW OF INDICATOR 2 2 KEY FUNCTIONS 2 3 CONNECTING LOAD CELL TO INDICATOR CHAPTER 3 OPERATION 3 1 POWER ON amp ZERO SETTING 3 2 MANUAL ZERO SETTING 3 3 TARE 3 4 ACCUMULATING 3 5 COUNTING 3 6 USER FUNCTION STEETING 3 CONNECT SCOREBOARD TO INDICATOR 3 8 SERIAL COMMUNICATION AND INDICATOR COMMECTION CHAPTER 4 CALIBRATION CHAPTER 5 ERROR INDICATION CHAPTER 6 CHARGEABLE BATTERY CHAPTER 7 MAINTENTANCE Floor Pallet Scale sle Chanter 1 Main Specification Model Accuracy Sample Rate Load cell sensitivity Scale interval Display Power supply D N AD OO wae EE N Transporting temperature Operating temperature humidity DWP 5500R Floor Pallet scale Grade III n 5000 10 times second 1 5 3mV V 1 2 5 10 20 50 for option 6 bits LED 6 state indicating signals Battery DC6V 4AH 0 40 C lt 90 RH 20 50 C Before installation please first recharge the Transmitter for 24 hours The switch needs to be left ON during recharging Floor Pallet Scale Chanter 2 Installation 2 0 SCALE BASE SETUP a Open the scale base box Box 1 with a knife very carefully Sharp blade may scratch the scale surface b Take out the scale feet total 4 feet packed in the box inside the scale base
4. If it is not correct adjust it as following Press ZERO key to change hour the hour is blinking Press TARE to add up until it shows the correct hour Press ZERO to move to the minutes the minutes are blinking Press TARE to add up until it shows the correct minute Press ZERO to move to the seconds the seconds are blinking Press TARE to add up until it shows the correct second Press FUN to confirm and move to date mode setting There are 3 date showing modes YY MM DD MM DD YY and DD MM YY Press TARE key to switch between and press FUN to confirm then move to date setting Use the same way as timing setting to set the date Press FUN to confirm and exit During the time or date setting you may press MOD anytime to cancel and exit System will not save the changes Press TARE to move to the next parameter 4 2FAST CALIBRATION FOR ZERO POINT AND FULL RANGE POINT Press while it is initialization it enters into the calibration mode 4 2 1 Fast calibration for zero point At any time before it shows nOLOAD press FUNC it keeps the original division decimal point full range and enter into the zero pointalibration mode Press ZERO when the stable signal is on it displays End and keeps the original full range point calibration Press the calibration switch under the lead sealing board at the back of the indicator it saves the setting and back to the weighing status 4 2 2 Fast calibratio
5. line of load cell 7 7 During operation if trouble occurs operator must pull off the power supply plug immediately and user should return this indicator to our company for repair No n weighing manufacturer should not repair it or by yourself otherwise further destruction may happen 7 8 The storage is not granted the free repair guarantee because it is easily exhausted products In order to prolong using life please charge the cell fully before using it If you don t use the indicator for a long time you must charge the cell every two month and for eight hours each charging time K Moving or installation must be carefully taken and must avoid strong vibration impact and bump in order to protect the storage cell from being damaged 7 9 From invoice date the indicator has a one year free repair period If any non artificially obstacle about the indicator happens under correct using conditions within this period the user is allowed to send the product with its guarantee card of the correct number back to our corporation for free repair The indicator shouldn t be taken apart otherwise free guarantee will be cancelled Floor Pallet Scale ll
6. the indicator will set alarm for a weighing range To set check weighing parameters when the indicator is off turn it on and press ZERO key when the indicator is still warming up You will see F1CLK on the screen Press TARE key 3 times and the screen will show F4 CHK Press FUN key to enter beep mode setting Beep 1 No beep When the weight is higher than the high limit HI will be on When the weight is lower than the low limit LO will be on Otherwise both HI and LO will be on Beep 2 Beep when the weight falls into the weight range Beep 3 Beep when the weight falls out of the weight range Press TARE key to select desired mode then press FUN key to set High limit Now there are 6 zeros on the screen Press ZERO key to move the editable digit blinking and press TARE to change the value When you are done press FUN to set Low limit When you are done press FUN to confirm The screen will go back to F4 CHK To disable the check weighing function press UNIT key to set both high limit and low limit to Zero 3 10 PRINTING WHEN F3 KEY 2 Set P 10 as RS We will show to how to set P value later on In the weighing mode press MOD to print Floor Pallet Scale 9 Chapter 4 Setting Parameters To enter parameter setting Turn on the indicator and press ZERO key when the indicator is still warming up 4 1 F1 CLK DATE AND TIME SETTING Press FUN key to show the current time
7. ZERO key to clear the memory Floor Pallet Scale 8 3 6 WEIGHT HOLDING FUNCTION WHEN F3 KEY 3 Press MOD key to hold the readout press MOD again to release 3 7 PRE TARE FUNCTION WHEN F3 KEY 4 Press MOD key to enter Pre pare Setting Press ZERO to move the editable digit blinking and press TARE to change the value Make the displayed value equal to the container which needs to be tare for every load Press FUN to confirm The display will show the negative number for tare value 3 8 ANIMAL WEIGHING WHEN F3 KEY 5 Press MOD key to set parameters of animal weighing 1 Stable time Fil n n value can be changed n value options 1 2 3 4 5 1 is the fastest and 5 is the lowest Press TARE to select the desired value and press FUN to confirm and move to the next parameter 2 Display Range Rang n n value options 1 2 3 2 is recommended PBARE to select the desired value and press FUN to confirm and move to the next parameter 3 Lock Range If the change of weight exceeds the input value the indicator will refresh the display Press FUN to confirm 4 Press FUN to start animal weighing Press FUN again to exit 3 9 CHECK WEIGHING Check weighing is a function to control the items to be weighed within or without the pre set range If the high limit and the low limit are set as same value the indicator will set alarm for one key point If the high limit is set higher than the low limit
8. n for full range point At any time before it shows AdLOAD press ACCU it keeps the original division decimal point full range zero point calibration and enter into the full range point calibration mode When it is finished press the calibration switch under the lead sealing board at the back of the indicator it saves the setting and back to the weighing status EER1 TneAD value is too small when calibrated U I I EER2 The zero point is out of range when calibrated EER3 The zero point is out or range upon staring U _EER4 The imputed sample number is zero when sampling n counting mode EER5 The imputed weight is zero when full scale calibrated in calibrating mode EER6 The unit weight is less than 0 25e when sampling in counting mode bilo Lowpower o O Floor Pallet Scale 10 Chanter 6 Recharge Battery 6 1 Turing on the AC power the indicator willre charge the battery automatically So if you don t use battery frequently you should take battery out m Note red end is black end is Wrong connection will destroy indicator Note The built in battery should be fully charged before it is used for the first time 6 2 Only when you turn off the AC power and push start key battery works Displaying LouoL means the insufficient of voltage it needs charge 6 3 When you use the battery first time you should charge the battery for 20 hours in order to prevent low voltage resulted from
9. n the STAB sign is on 3 3 TARE FUNCTION When Indicator is in weighing mode press the Tare key the indicator will deduct the displayed weight value as tare weight Then indicator displays net weight as 0 and Tare sign is on 3 4 COUNTING FUNCTION WHEN F3 KEY 1 Sampling Tare the weight of any container that is used and leave the container on the scale Place samples on the scale The quantity of the samples should match the options for the pre set values 10 20 50 100 or 200 pieces Press MOD key and the screen will show P10 which means the requirement of the sample size If the sample quantity on the scale is not 10 pieces press TARE key to select the according sample size Press FUN key to confirm Counting Remove the samples from the container and place the items need to count into the container You can see the counts on the display Press FUN key to view Unit Weight in gram Counts and Total Weight You may exit counting mode anytime by pressing MOD key 3 5 ACCUMULATING FUNCTION WHEN F3 KEY 2 In weighing mode press FUN key to enter accumulating mode Place the first item onto the scale and wait until the STAB sign on Press MOD key to store the weight into memory Remove the first item and place the second item onto the scale then repeat the previous procedure Maximum loads for one accumulating is 200 Clear the scale platform and press FUN key to view the number of loads and total weight Press
10. the self leakage of the battery 6 4 If you don t use battery for a long time you should charge the battery for 10 12 hours for each 2 month to prolong using life of battery 6 5 The battery is easily exhausted products And it is not granted free guarantee Chapter 7 Maintenance 7 1 To guarantee indicator clarity and using life the indicator shouldn t be placed directly under sunshine and should be set in the plain space 7 2 The indicator can t be placed into the place where the dust pollution and vibration are serious 7 3 Load cell should connect with indicator reliably and the system should be well connected into ground The indicator must be protected from high electrical field and high magnetic field m In order to protect the operator indicator and relevant device you should mount lightning rod in thunderstorm frequently happening area m Load cell and indicator are static sensitive device you must adopt anti static measures 7 4 lt is strictly forbidden to clean the case of indicator with intensive solvents for example benzene and nitro oils 7 5 Liquid and conducting particle should not be poured into the indicator otherwise the electronic components will be damaged and electric shock is likely to happen 7 6 You should cut off power supply of indicator and relevant device before you pull in and out the connecting line of indicator and external device s You must Cut off power supply of indicator before pulling out connecting
Download Pdf Manuals
Related Search