iViewHD-2M Information
Contents
1. ViewHD 2M IP Security Camera 1600x1200 Two Megapixel Resolution The NetMedia iViewHD Two Megapixel 2Mp Internet Protocol IP camera connects to a Power over Ethernet PoE network switch such as the NetMedia POEmax for distribution across a local com puter network or The Internet It provides live viewing of its Motion JPEG MJPEG images through various web browsers such as Microsoft Internet Explorer Apple Safari Mozilla Firefox and Google Chrome Live viewing plus recording and playback are also available through Network Video Recorders NVRs that support MJPEG video streams and manual custom generic camera command strings Product Includes Please visit iViewHD com 1 iViewHD Camera Housing Camera for full User Manual and Lens Ethernet Jack Reset Button camera firmware updates Speaker Power LED 2 Mounting Hardware Slide Mount Base Screws Anchors Camera Lens F3 2 59 9 diagonal angle Speaker Reset Button Press during power up to reset camera MAC Address Unique Ethernet ID Inside Beeps when powered on Red LED Indicates Power Yellow LED Slide Mount e Slide Rail and Slide Nut attach p i and adjust camera on base Ethernet Jack RJ 45 for video and power via PoE network switch Green LED Indicates network data link Swivel Screw Adjusts camera angle Mounting Anchors e Secure screws in walls Mounting Screws AK Fasten Camera Base to surf2. Home or Commercial Use Type of Equipment Internet Protocol Camera Model iViewHD 2M to which this declaration relates are in conformity with the Title 47 of the US Code of Federal Regulations Part 15 covering Class B digital devices Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Warning This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to a different outlet on a circuit other than the one the
3. ace p e Camera Base Mounts camera to surface S FEATURES SPECIFICATIONS High resolution Two Megapixel 1600x1200 image Camera Lens F3 2 59 9 diagonal Variable resolution 1600x1200 to 160x120 Image Sensor Two Megapixel 2Mp 1 4 CMOS Power over Ethernet PoE operation Output Connector TCP IP Power over Ethernet RJ 45 IEEE 802 3af compliant Supported Formats Motion JPEG MJPEG Still JPEG Requires no power supply Supported Resolutions 1600x1200 160x120 SXGA XGA SVGA XD1 VGA QVGA CIF Electronic exposure and white balance Power Requirement Power over Ethernet PoE 2 5 Watts Up to 4 IP addresses DHCP Link Local 2 Static Housing Size 2 9 long x 1 1 wide x 2 75 high Rugged aluminum housing Housing Weight 4 02 FCC Class B and CE certification See 2 7 wide x 2 7 high Base Weight 3 02 One year limited warrant d Y subject to change without notice 2009 NetMedia Inc All rights reserved NetMedia and iViewHD are either registered trademarks or trademarks of NetMedia Inc Any other trademarks or trade names mentioned are the property of their respective owners NetMedia Inc 10940 N Stallard Place Tucson Arizona 85737 520 544 4567 Fax 520 544 0800 Email sales netmedia com www netmedia com MAN iViewHD 2M REV0912A W2 OHMaiq NiewhD 2M Quick Setup Procedures 1 Mount base to desired surface using included hardware Remove packing material from camera Slide Rail
4. and attach Slide Nut to base Swivel Screw Readjust camera angles once image is available through browser 2 Connect Ethernet Jack to Power over Ethernet PoE network switch or injector that also connects to computer network 3 To find the camera on your network open the Standalone Bonjour Browser available from iViewHD com downloads or open a computer browser that supports Bonjour mDNS such as Apple Safari 4 View image or change camera settings such as resolution and compression if desired Press Save Parameters button to make new settings the default 5 Connect to an NVR for recording and playback as directed by its product manufacturer using iViewHD s IP address iViewHD s port default 80 and iViewHD s minimum get image command string http IP Address image cgi CAPT URE YES amp STREAM 1 amp COMMAND 6 See the User Manual for complete instructions and additional methods of locating the camera Router DHCP Server iVieWHD IP Camera PoE Power Source Computer w Web Browser Figure 1 Connect iViewHD to PoE network device such as NetMedia POEmax switch for power and computer connectivity BS fon joie Brier for Windies Jaaa Hare i aiaa ok AAP Bae Statin MHD IM Comes TOOR 163754 2984 A0 e Double click iViewHD E eS DETH eo o eer ee camera to launch it in your Fennel i default web browser Select Web Server HTTP Secure Stell SSH Creel Pie Tance D F from Bonjour Services Bainig P
5. ils Share nt AAD ee ooo r oise Figure 2 Running the Standalone Bonjour Browser to find your iViewHD camera and display it with a web browser Arun rH nage Coning WicwHD Image inf Services P Secoity Admin Upisi Navigation Bar Help and _ e amp Information Area Camera Image Frame Rate Information Footer link to iViewHD com Save and Restore Parameters buttons e Por oar Ecard T S Pana yt HE WH 2 re ae Fi eer ro ee i Figure 3 iViewHD Image page for viewing camera output and areen saving and restoring camera settings P a a e M eee eee NetMedia Inc 10940 N Stallard Place Tucson Arizona 85737 520 544 4567 Fax 520 544 0800 Email sales netmedia com www netmedia com NetMecia gt MAN iViewHD 2M REV0912A W2 OHMaiAl 1600x1200 Two Megapixel Resolution FCC Information U S A Important This product when installed as specified meets FCC requirements Modifications not expressly approved by NetMedia may void your authority granted by the FCC to use the product Failure to follow all installation instructions could void your FCC authorization to use the product in the USA FCC Compliance Information Statement iViewHD 2M Camera tested to comply with Declaration of Conformity Procedure We NetMedia Inc C 10940 N Stallard PI Tucson AZ 85737 520 544 4567 declare under our sole responsibility that the following products For
6. nds included afterwards Some example commands are e COMP 0 45 Compression level Default 11 0 is lowest compression best image quality large file size 45 is highest compression worst image quality small file size e MODE UXGA SXGA XGA SVGA VGA QVGA QQVGA or CIF or numeric corresponding value 0 8 Default XD1 UXGA 0 1600x1200 SXGA 1 1280x960 XGA 2 1024x768 SVGA 3 800x600 XD1 4 720x536 VGA 5 640x480 QVGA 6 320x240 QQVGA 7 160x120 CIF 8 400x298 e RATE 0 2 default varies based on resolution and compression 0 Best for Night 1 Better for Night 2 Best for Day This example streams images at QVGA resolution with compression level 6 and Better for Night frame rate image cgi CAPTURE YES amp STREAM 1 amp COMMAND MODE XD1 COMP 6 RATE 1 a i ee ca em a a a a a ac a ee a a ee NetMedia Inc 10940 N Stallard Place Tucson Arizona 85737 520 544 4567 Fax 520 544 0800 Email sales netmedia com www netmedia com NetMecia gt MAN iViewHD 2M REV0912A W OHMaiAl
7. re limited to the warranty stated above NetMedia shall not be responsible for any loss damages or expenses whether direct consequential or incidental that arise from the use or inability to use this product Some states do not allow limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state MAN iViewHD 2M REV0912A W OHMaiA Frequently Asked Questions Q How do update the firmware or web pages in my camera A Download and unzip the latest version from iViewHD com Select the camera s Update tab Browse to and select the unzipped files Firmware first Website second on your computer then press Update iViewHD Q Where do get the full iViewHD User Manual A The User Manual is available for viewing and downloading from the iViewHD com website It contains more detailed information about the camera s controls web pages and commands along with helpful information regarding networks and finding the camera with or without Bonjour Q Where can I get more help for setting up my camera or putting it on The Internet A The iViewHD user forum at http www netmedia com forums provides an environment where users and developers share knowledge for implementing supporting and improving the product and its features Q How do make my camera settings the default ones on start
8. receiver is connected to Consult the dealer or an experienced radio TV technician for help CE Mark Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures One Year Limited Warranty NetMedia Inc warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or at its option replace the defective product Please keep your purchase receipt In the unlikely event that you need warranty service call NetMedia at 1 520 544 4567 for a Return Material Authorization RMA number Then return the product with the RMA number clearly marked on the package by a traceable method with freight pre paid and accompanied by a copy of the purchase receipt to Attn Customer Service NetMedia Inc 10940 N Stallard Place Tucson AZ 85737 9527 No expressed or implied warranty is made for any defects in this product which result from accident abuse failure to operate the product in accordance with relevant instructions neglect immersion in or exposure to chemicals or liquid extreme climate excessive wear and tear and defect resulting from other extraneous causes such as unauthorized disassembly repair and or modification Any implied warranty arising from the sale of this product including implied warranties of merchantability and fitness for a particular purpose a
9. s support MJPEG directly The extra Flash processing slows down browser performance The Opera browser does not require Flash but it displays better with the Flash option Q How can control the camera settings through an NVR or custom web page A iViewHD accepts HTTP commands that may be used with NVR software or custom web pages to control the operation of the camera These commands are case sensitive See the User Manual for more information including the complete command list The general form of the HTTP command string is as follows http IP Address image cgi CAPTURE YES NO amp STREAM 0 1 amp COMMAND commands IP Address is the IP Address or the Bonjour if installed name of the camera e YES NO is either the word YES or NO and is used to indicate if an image is to be CAPTURED after the commands that follow are processed Usually you set this to YES to begin capturing video or still pictures You would set this to NO if you just want to change some camera parameter without receiving an image This is useful if you are changing parameters while another computer is capturing images e 0 1 is either the number 0 or 1 and indicates if images are to be streamed or not A 0 means only a single JPEG image is to be returned while a 1 means that multiple JPEG MJPEG images are to be returned streamed e commands is a list of Commands separated by commas described below The COMMAND parameter should always be present even if there are no comma
10. up A The Save Parameters button will make your settings active when the camera starts The Restore Parameters button will reload your saved settings Reloading a new firmware or website version pressing the Set to Factory Defaults button Admin Page or using the camera Reset Button will erase your saved settings Q Why does my frame rate automatically change and how can I maximize it A There is a camera frame rate and a browser frames per second fps rate The camera rate is how fast it can produce an image It is primarily affected by light conditions resolution and compression The fastest rate is Best for Day but it requires bright light In addition the camera may automatically change to Best for Night under certain conditions such as UXGA mode The fastest camera rate is achieved with bright light Best for Day low resolution lt VGA and high compression gt 20 The browser fps rate reflects the camera rate plus computer and browser speed plus network speed plus network bandwidth Large amounts of network data transfer from this camera other cameras and other network devices will drastically reduce bandwidth The fastest browser fps is achieved with a fast camera frame rate across fast high bandwidth local network equipment to fast computers Q Why does Internet Explorer seem slower than other browsers A Internet Explorer must use the Adobe Flash plugin to display Motion JPEG images whereas the other browser
Download Pdf Manuals
Related Search