Home

LPE3510 (13”) LPE6510 (25”)

1. etc in two Insert the paper several times between the rollers with folded side first Cleaning periodically by wiping with arag soaked with methyl or ethyl alcohol is recommended because old adhesive cannot be easily removed Never use organic solvents toluene benzene thinner etc Do not use thin paper e g copying paper for the cleaning of the rollers as it may cause jamming Do not use metal or sharp materials to remove glue from rollers Use Dry Lam s Maintenance Kit part number 01300 to lubricate the face of the Heat Chambers between film roll changes Doing so will allow film to pass effortlessly over them producing higher quality laminations with less back tension from the Chambers The lubricate will also increase the effective life of the chambers See your dealer or contact Dry Lam for this part 7 LAMINATING FILM It is recommended to use Fujipla Dry Lam or other quality films See your dealer 8 SPECIFICATIONS MODEL LPE3510 LPE6510 Maximum Laminating Width 13 25 Laminating Film Thickness 1 5mil or 3 0mil Laminating Speed 4ft min 3ft min Temperature 194 F 305 F adjustable Power Source AC120 V 60Hz Current 6 7A 11 7A Current Power 800W 1400W Carton Dimension WxLx 21 7 x15 4 x15 33 5 x15 4 x15 6 H 6 Net Shipping Weight 50 61LBS 62 80LBS Remarks The room temperature should be within the range of 32 F to 100 F The recommended room tempera
2. ator Be certain that the threading card exits the rear of the machine Allow the threading card to drop towards the floor as the machine runs If the threading board does not exit the machine STOP THE MOTOR and use the reverse function to bring the card back out the front Left to run in this manner will cause damage to delicate parts on the interior of the machine 4 OPERATION cont d Creases or wrinkles may appear in the film as it exits the rear of the machine Observe the film at the face of the Heat Chambers There may be the occurrence of creases or waterfall of the film along the chambers They should disappear shortly If they do not disappear adjust the film tension e To increase tension rotate Tension Controller clockwise e To decrease tension rotate Tension Controller counter clockwise Notes During lamination be sure that Safety Cover and Feed Table are securely set If READY lamp does not glow stop the lamination until the lamp glows again Rollers rotate in reverse when Motor Switch is turned to REV Do not use this function except in case of emergency If the REV is used film may back up into the lamination area and cause a jam 5 FINISH OF LAMINATION Switch OFF Motor Switch Turn off the Power Switch and unplug 6 CLEANING OF ROLLERS Clean rollers when necessary An excess of adhesive stuck to the rollers may cause film jamming Fold a sheet of paper e g calendar catalogue
3. er or disassemble the machine unless directed by Dry Lam s Tech Line If problems e g jamming etc occur switch off and unplug immediately and then contact Dry Lam s Tech Line Be careful that your tie necklace hair etc do not get caught in the machine In such a case switch off immediately Do not spill water on the Lamipacker Do not operate it with wet hands Do not set the Lamipacker on the power cord Be sure to unplug before moving the Lamipacker The surface of Lamipacker and laminated objects may be hot Do not laminate prohibited materials see next item laminating objects on page 4 In the case of incorrect threading setup laminating prohibited materials or laminations performed incorrectly smoke may come out of the laminator The safety cover should always be placed correctly Always ventilate the area well when operating The laminator should be located close to the wall outlet and easily accessible Recycling Information Thank you for choosing this Fujipla product It is an electronic device containing components which require proper disposal at the end of their effective life You can help control emerging risks by disposing the electronic device and your domestic waste separately Electric and electronic devices are marked with a crossed out waste bin indicating that these products should not be dumped together with domestic waste If being dumped together with domestic waste electric and electronic equi
4. kness e Objects which change color or quality with heat e g thermal paper pictures drawn with crayon etc Operation e Operate the Lamipacker only for lamination of paper items e Do not leave the Lamipacker during operation 1 NAMES AND FUNCTIONS Name of Components Mandrels Heat Shoe and Heat Rollers Safety Cover Tension Controllers Upper Guide Roller Operation Lever READY Lamp Control Dial Power Switch Motor Switch POWER Lamp Front Guide Plate Rear Tray Power Cord Feed Tray Lower Guide Roller 01 000 SLO SU GOs IN ES PRPRPRrPRPPR nUuUBWNF OO 2 FILM SETTING Insert Mandrel into the film roll Upper amp lower Be sure the direction of hooks is in the reverse direction of the film rotation fig A fig A Set the film roll and Mandrel on the machine Upper amp lower Be sure the adhesive side of the film is facing you not the Heat Chamber fig B fig B Hook Hook Resin side Resin side How to load the adhesive inside film How to load the adhesive outside film Pull out the end of the upper film roll and pull the film down in front of the Heat Roller passing it over the Upper Guide Roll as illustrated Pull out the end of lower film roll passing the film around the back of the Lower Guide Roller Adjust the position of upper and lower films so that edges of the films align Put the end of lower film over the upper film NOTE Adhesive outside fil
5. m is not a common film type 3 WARMING UP Set Operation Lever to LAMINATE position Turn on Power Switch POWER lamp red will glow e LAMINATE Rollers will be closed e OPEN Rollers will be opened 3 r Set temperature according to the object to be laminated Operation Lever Machine gt LPE 3510 13 LPE 6510 25 Item to be laminated Film thickness Film thickness 1 5mil 3 0mil 1 5mil 3 0mil Thin Paper Copying Paper 6 7 7 8 7 8 7 8 Printing Paper Brochure Thick P Busi Thick ic aper usiness Card Thic 7 8 3 9 3 9 3 9 Printing Paper Photo Paper The setting may be affected by room temperature conditions Lamination is an art form Experimentation is the key to successful results The above settings are for School Lam film There are some higher quality films which will melt at lower temperatures Consult the directions for the film being used READY lamp green will glow indicating the machine is now ready for laminating 4 OPERATION Level the rear tray to the operation position Overlap upper and lower film in the front of Heat Shoe Set the Operation Lever up to OPEN Position a Film Setting Board between the Heat Rollers together with films Set Operation Lever down to LAMINATE Switch the Motor Switch to the FWD position and pass the film web through the rollers using the film setting board threading card included with the lamin
6. pment may have severe impacts on the environment as well as human health the least of which due to the possibly of hazardous materials In accordance with the European WEEE directive Fujipla provides an easy way to recycle waste of electric and electronic equipment Please dispose of electric and electronic equipment waste by using your local collection site for this type of waste SAFETY PRECAUTIONS For safe operation be sure to observe following precautions Installation 1 Donot install the Lamipacker in a humid dusty area or near an air conditioner 2 Install Lamipacker on a level surface and leave enough space in the rear to guide laminated objects out the exit 3 Do not put anything on top of the Lamipacker 4 Becertain that the power source connects to a dedicated and grounded AC120V 60 Hz outlet Do not share the electrical outlet with other devices 5 Use ina well ventilated room Laminating film e While genuine FUJIPLA CP Roll is recommended any quality 1 5 or 3 mil laminating film may be used Contact your dealer Laminating objects Lamination is made by heat and pressure Inappropriate operation may cause failure in quality of lamination or in jamming of film Avoid lamination of the following e Inflammable substances or any substance susceptible to heat e g vinyl chloride polyethylene etc e Valuable items which are unique and not replaceable Do not laminate money e Lamination items which exceed 35mil In total thic
7. ture is 68 F The machine can only be used at an altitude below 7000 feet Specifications may be modified without prior notice 9 WARRANTY This product is manufactured under a strict quality control system and has undergone stringent testing at our factory To make sure however we guarantee the product under the following terms and conditions Should a failure arise under normal operating conditions we will provide the labor to replace any defective part deemed to be due to a manufacturing defect without charge to purchaser provided that the product is brought or shipped in to our dealer or our authorized service center We will charge the purchaser for defects subject to the following cases even in the warranty period Any breakdown or damage arising from abuse neglect or any alteration or modification to the machine Any breakdown or damage from fire earthquake or any act of God Any visual changes in cosmetic parts caused by normal use Any charges for shipping and shipping damage This warranty does not cover articles that cannot be laminated satisfactorily To inquire about maintenance or to order laminating film please contact your FUJIPLA dealer or Dry Lam end
8. uuiP LAMIPACKER Instruction Manual Models LPE3510 13 LPE6510 25 For safe operation be sure to read through this instruction manual before operating your Laminator FUJiPILA c UL US ID Card System Laminating Machines amp Film FUJIPLA Inc LISTED TOKYO JAPAN CONTENTS PAGE Warning before using your Lamipacker 3 Safety Precautions 4 Names and Functions 4 Film Setting 5 Warming Up 6 Operation 7 Finish of Lamination 9 Cleaning of Rollers 9 Laminating Film 9 Specifications 10 Warranty 11 Thank you for your purchase of the Fujipla LPE3510 or LPE6510 laminator This laminating machine is designed to laminate most common paper stocks inks and toners with transparent lamination film Laminated objects are waterproof and durable as well as having a lustrous appearance Please note that once laminated it is difficult to peel off the film from the laminated object without damage to it Be sure to read this instruction manual thoroughly before operating your Lamipacker to avoid danger and the possibility of poor quality laminations Dry Lam LLC is the exclusive distributor of Fujipla products in North America Contact Dry Lam s Tech Line at 888 633 1973 x8575 for any service related issue WARNING BEFORE USING YOUR LAMIPACKER Do not dismantle gt Warning tangling gt Electric shock gt Warning Hot Do not open the casing of the Lamipack

LPE3510 (13”) LPE6510 (25”)

Contents

Download Pdf Manuals

Related Search

Related Contents

LPE3510 (13&rdquo;) LPE6510 (25&rdquo;)

Contents

Download Pdf Manuals

Related Search

Related Contents

LPE3510 (13”) LPE6510 (25”)