ｓｌｉｄｉｎｇ ｇａｔｅ - Hekopener.nl
Contents
1. can t close or open completely To activate this function press P I SET button on the PCB for 2 seconds while the PCB is on After releasing the P 1 SET button it will enter the open close learning mode as below The system will close the gates first Remove any obstacle could possibly block the gate Before the motor start the warning light will blink OCEITIGSOE The sequence of the learning process will be open stop close fully open fully close fully NOTE The Open Close Learning might not be done successfully due to the over weight of the gates Meanwhile the Current Limit VR4 needs to be increased a bit Please refer to page 13 of this manual If any assistance is needed please contact the technicians of our agent Remote Learning activation of remote control for gate operation To activate the remote control service please proceed the following steps A RF gate learning for Open Close the Gate 1 Press and hold P2 RADIO button on the PCB until the LD2 red LED lights up while the PCB is on now the learning mode is entered lt lt 2 Press any button on the remote control LD2 will now blink for 3 times learning succeeded or light off after 10 seconds without blinking learning failed please try again the whole process 3 Please learn the next remote control right after the 3 blinks of LD2 If no blink followed please repeat step 1 and 2 otherwise the unlearnt remote control won t be re2. try again Check out the wiring according to page 5 7 Make sure the VR2 is not at the maximum point Check alignment and reassure the wiring of the photocell Factory settings of Adjustments VR1 VR2 VR3 VR4 FOR PAU OBS OVL Please note The adjustment has a maximum rotation of 1 turn beginning from the CCW end to the CW end Please do not force the adjustment past the stop points VR1 Adjustment on motor speed CW speed up CW ccw CCW slow down VR2 Auto Close Timer CWe increase waiting time CCW decrease waiting time This timer works also as a swtich for revolving command mode VR2 CW ccw when it s turned to the end of CW direction It maks the system Ks close the Auto Close function and do Open stop close stop open in turns when you press the remote control CW to Maximum VR3 Obstacle Detection CW increase tolerance time to react while the gate runs into an obstacle CCW decrease tolerance time to react while the gate runs into an obstacle CW CCW VR4 Sensibility CW DECREASE sensibility to the resistance against sliding for heavy gate or badly maintained gate CW cCW CCW Increase sensitility to the resistance against sliding for gate which slides smoothly Specifications 350KGS 770Lbs Max 3 1M 1O0Feet with 6 tooth racks MO GOS 3 I 003 Ver 071130A
3. USER S MANUAL SLIDING GATE OPENER _Supenjack sliding gate Equipped with quick release keys for gear clutch Remote control with 433MHz Rolling code Soft stop function which treasures your gate Adjustable Auto close function Content of the Kit x2 Release Keys x4 Limit blocks Wiring Diagram Warning Garden Light QA Lamp or installation Control inside Garden Warnin Lamp A m Light VIII EE HH E E HH HEEL LELEEEELELER a O ee T A T a Important Safety Advice 1 Knowledge of the relevant electro technical regulations is required 2 Training in use and maintenance of safety equipments is necessary 3 Professional assistance is required when some mechanism adjustment is needed 4 Always lay mains and control cables separately 5 Test every equipment before initial operation 6 Make familiar with the use of the system before initial operation 7 Unplug the mains before attempting to connect power cable to the system Measurements mm Qualification of a properly designed sliding gate As a general rule an automatically operated gate must be stronger and smoother than a manually operated gate Since the gate is a major component of the system great care and concern must be given to the gate design A poorly designed gate can damage a gate operator Check if the gate slides smoothly on the rail without binds or excessive res
4. cognized by the system Remote Control Operation with revolving commands open close and stop by remote control When the VR2 is turned to the end of the CW direction the system operates with revolving commands which no Auto Close function will follow Button A or C the first press will open the gate fully next press to stop next to close the gate next to stop and so on Button B or D the first press will open the gate for pedestrian to pass next press to stop next to close the gate next to stop and so on When opening the gate 1 Warning light will blink for 3 seconds then gate opens 2 If the gate hits something the motor will reverse a bit and wait for next command When closing the gate 1 The motor will close after the warning light blinks for 3 second 2 If the gate hits something the motor wil reverse a bit and proceed Auto Close function twice in case any obstruction is still on the way After that the system will halt any action and wait for next command Remark The gate operation works properly only after sucessful Opening Closing Learning Photocell triggered during the rotation of the motor 1 While opening the gate will still go on with opening 2 While closing the gate will open fully and ready for Auto Close Function 3 During Auto Close Function the gate will stand still upon triggered photocell The gate will close as soon as the photocell resumed Auto close SuperJackw
5. he motor 6 Insert and turn the key counterclockwise and pull to release the motor clutch and move the gate to see if the gate slides well l l 1 Fitthe limit block to the tooth rack atthe intended position fix the limit block with the screws provided 3 W s n 8 Lock up the clutch 9 Make sure the power cable is disconnected from the mains and connect the three wires to the power socket in the system Neutral Ground Phase Functional diagram Auto Close Timer Obstacle Detection Sensibili Speed Trimmer VR1 VR2 VR3 VR4 uU O UYU LD1 1D2 jl e x E P1 SET P2 RADIO e n Nn NI EL STR w PEDSTP FCL w FOP LAMP gale ie MOT BAT 12 24V Transformer ANT wv VA TXF EDG PHO w Radio Antenna Battery P hotocell Motor Limit S witch Extented Control J umper wire can be torn down and connect the wires of an emergence Wiring with PCB stop button to the terminals ANT w VA TXF EDG PHO vy EL STR Y FCL w FOP LAMP MOT ED VU BAT 12 24V a qd Bi e I oO Additional E Antenna d b z E q D th COM ATOT GND Safety Edge Qi poog DC GND NO NC COM TM Wiring of exterior manual buttons ANT w VA TXF EDG PHO v EL STR w PED STP FCL w FOP LAMP leeke e MOT BAT 12 24V Emergency Stop O O Open gate partially Open gate by pushing manual button or by i
6. ill close the gate automatically after the gate has been opened for a certain period of time as set by turning the VR2 adjustment on the PCB 0 90sec Please note If the VR2 is turned to the stop point of the adjustment in the CW direction NO Auto Close funciton will proceed Operation with revolving commands open close and stop by remote control on page 10 Clear RF memory Press P2 RADIO button on the PCB until the LD2 flashes let go the button and press the button again until the LD2 flashes 6 times at a faster speed RF memory is cleared Quick release The SuperJack series are equipped with a clutch mechanism inside the motor to provice user with an alternative to open the gate manual during power failure Please unlock the clutch only when the motor is static Sleeping mode during Battery low The SuperJack system will be forced to enter the sleeping mode when the battery is low During the sleeping mode all funtional features will be seized until power recovery Operation of Photocell Select a proper installing location where the IR transmitter and receiver along the same line and at the same height Connect the wires of the photocell to the operator s PCB as wiring diagram above Power on the system try and see if it works properly by obstructing the IR between the transmitter and receiver for some times The relay in the receiver should respond accordingly while LED switches ON and OFF With photocell wel
7. istance The rail has to be level so the gate will slide without resistance on it The gate structure must be an in line structure and has a ballanced center of gravity U pper roller guides The gate must be equipped with a set of roller guide with at least 2 rollers in one line E Roller guides A Caution A stopper on each end of the rail is required to bring the gate back to still condition and prevent the gate from getting off the rail oW Wheels To keep the gate sliding smoothly the shape and size of the wheel should suit the shape and size of the rail so there will be no resistance coming from the friction Four screws to secure the motor adjust the screws at the four corners of the plate to make the plate horizontal 1 Prepare a concrete block and drill four holes in the block to fit the metal base plate for the motor Keep a proper distance between the edge of the plate and the tooth rack 2 Pass the power cable through the big hole on the plate 3 Adjust the screws and nuts to level the plate A 4 Adjust the position of the motor to make the tooth rack connect with the tooth cog wheel of the motor leaving 2 3mm vertical distance between tooth rack and cog wheel 2 3mm Keep a distance of about 2 3mm between tooth rack and the output cog wheel through out the full length of the rack v N Four screws to secure t
8. l installed while it s triggered during sliding open the system will ignore the IR obstruction and still go on with opening While it s triggered during sliding close the gate will reverse a bit then stop and wait for next command Troubleshooting 12 No Power Emergency shut down activated Fuse burnt No response when open command Is given neither the gate moves nor the motor starts Defect power cable to motor Obstruction of Photocell beam Button jammed Wrong wiring on the limit Switches or PCB Plug the power cable to the system Make a jumper between the STP and earth on the terminal bus page 5 Replace with a new fuse Replace with proper power cable Make sure the Photocell well aligned and not obstructed Make sure the buttons on the remote control and interphone are functioning well Check out the wiring according to page 5 Make sure the roller guides is well lubricated and unlock the clutch to slide the gate manually ato see if it slides smoothly Clutch is open Lock the clutch up Gate slides badly The motor starts when it receives command but the gate stands still Insufficient motor force The gate closes while it should open Wrong connection on the terminal for motor The system is in the mode of revolving command The gate opens but never close Bad alignment of P hotocell Turn the VR4 CW a bit and
9. nterphone Press P1 button for over 2 seconds to proceed the open close learning of gate operating length P1 SET The system will learn where to stop softly according to the position of limit blocks Press P2 button for over 2 seconds the system will test the polarity of the motor Please check if the gate opens first P2 RADO and then closes In case the gate closes first then the wires of the motor have to be switched Jumper in The upper buttons of the remote control are selected A for fully open B for pedestrian s open Jumper out The lower buttons of the remote control are selected e le C for fully open D for pedestrian s open Wiring of the limit switch ANT w VA TXF EDG PHO vr EL STR w PEDSTP FCL w FOP LAMP Ale Eat MOT BAT 12 24V 5 oO Si a gt 5 oO o Additional E D Antenna zo oco 5 om d to the right hand side please connect the wires When the gate is supposed to be opene of the limit switch as shown below Open the gate this way lop View Factory default ANT w VA TXF EDG PHOW EL STR w PEDSTP FCL wr FOP LAMP Ale ee e AOT BAT 12 24V Additional Antenna When the gate is supposed to be opened to the left hand side please connect the wires of the limit switch as shown below Open the gate this way d uale Quick Start Connect the power cord motor photocells and warning light to the control box S witch on the control Hb the Polarit
10. y box and press PISET mad LD1 flashes of motor button for 2 sec J The gate opens a bit stops and closes fully LD1 lights up Learning mode entered Press P1 SET button gms Open Close Learning E The gate opens a Dit and then closes fully The gate opens fully The gate closes fully T 4 LD2 lights up RF Learning mode entered Press P2 RADIO RF learning button for 2 sec LD2 blinks for 3 times Press on any button remote control learnt on the remote control learn another remote control or abort auto matically Test the polarity of the motor To make sure that the motor rotates in right direction please proceed this function prior to the Open Close Learning Press P2 RADIO button on the P CB before the system finishes with 8 flashes of LD1 green LED right after the power connection After releasing the P2 RADIO button it will enter the test mode for the polarity of the motor as below m Remove any obstacle could possibly block the gate inn Before the motor start the warning light will blink The sequence of the learning process will be open stop close fully Check if the working directions are right as you need If not please switch the wires of the motor connected on the terminal of the PCB Open Close Learning Please proceed this function before using this product otherwise the system will drive the gates improperly E g The gate
Download Pdf Manuals
Related Search