Home

Digital Video Recorder User Manual

1. HIKVISION Digital Video Recorder User Manual UD 6L0202D1589A01 User Manual of DS 7200 7300 8100 Series DVR Hikvision Network Digital Video Recorder User s Manual This manual as well as the software described in it is furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Hikvision Digital Technology Co Ltd Hikvision Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical recording or otherwise without the prior written permission of Hikvision HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE REGARDING THE HIKVISION SOFTWARE HIKVISION DOES NOT WARRANT GUARANTEE OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS ACCURACY RELIABILITY CURRENTNESS OR OTHERWISE THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME
2. Folder 08 28 2013 15 55 28 i 14 16ME New Folder Figure 2 16 Export IP Camera Configuration File 2 Select the backup device from the drop down list You can click the Refresh button to get the latest information of the backup device 3 Click the Export button to export the configuration file of IP cameras to the backup device 4 Click OK on the pop up message box after the exporting process is complete The configuration file of IP cameras will be displayed on a list 2 2 2 Configuring the Connected IP Cameras Editing the connected IP cameras Purpose The detailed information of the added IP cameras will be displayed on a list and you can configure the basic setting of the cameras if needed Steps 1 Click the icon A on the camera list to enter the Edit IP Camera interface 38 User Manual of DS 7200 7300 8100 Series DVR Edit IP Camera D1 172 6 23 108 HIKVISION 8000 1 admin Admin Password Cancel Figure 2 17 Edit IP Camera 2 Edit the camera information such as the IP address protocol port etc 3 Click the button OK to save the new settings 4 To delete the added camera click the icon L1 Or check the corresponding checkbox and click the button Delete Description of the icons Add the online IP camera automatically Edit the basic parameters of the added IP camera E Delete the added IP camera Get the live view of the added IP camera i Upgrade the added IP camera
3. Export finished Export finished Figure 7 15 Export Finished S After the backup is complete the exported record files will be displayed in a list on the Export interface fers The Player program player exe will be exported automatically during record file export Device Name ANS Name Size Type Edit Date Delete Play Bi ch01_20130722141 23 684KB File 07 22 2013 15 50 20 m E ch01_20130722145 489KB File 07 22 2013 15 50 20 m a lii 7 639MB New Folder Format Cancel Figure 7 16 Checkup of Video Clips Export Result Using USB Flash Drive 126 User Manual of DS 7200 7300 8100 Series DVR 7 2 Managing Backup Devices Management of USB flash drive USB HDD and eSATA HDD Tuc The eSATA HDD is supported by DS 7300 and DS 8100 models only Steps 1 Enter the Export interface of backup device For details see Chapter 7 1 7 2 Device Name Name Bl a01_md_ch01_ 130 Bi ch01_20130722084 E ch01_20130722084 B player exe Size Type 2 626KB File 22KB File 22KB File 786KB File 7 660MB New Folder Edit Date 07 23 2013 10 17 28 07 22 2013 17 13 00 07 22 2013 17 13 00 07 23 2013 10 17 28 Format Refresh Delete Play Cancel Figure 7 17 Management of USB Flash Drives USB HDDs and eSATA HDD Export USB CD DVD RW B Export record files to m E Welcome to use backup ch03_201 10623000000 B ch03_201 10623042932 ch03_ 2011062309140 B h03 2011
4. Left Click Click and Drag PTZ control pan tilt and zoom Tamper proof privacy mask and motion detection Select target area Digital zoom in Drag and select target area Live view Drag channel time bar Right Click single Click Live view Show menu Menu Exit current menu to upper level menu Scroll Wheel Scrolling up Live view Previous screen Right click Menu Previous item scrolling down Live view Next screen Right click Menu Next item 1 4 Input Method Description 22 js s e 7 o o o io w e n r v u role lA s o r e n kLo B8BB ggBO Figure 1 5 Soft Keyboard Description of the buttons on the soft keyboard Table 1 6 Description of the Soft Keyboard Icons dm English Capital English mm s WI 0 m o 21 User Manual of DS 7200 7300 8100 Series DVR 1 5 Rear Panel DS 7204 The rear panel of DS 7204 DVR is shown in Figure 1 6 Figure 1 6 Rear Panel of DS 7204 DS 7216 The rear panel of DS 7216 DVR is shown in Figure 1 7 Figure 1 7 Rear Panel of DS 7216 NOTE The rear panel of DS 7208 provides 8 video input interfaces Table 1 7 Description of Rear Panel 4 HpMI HDMI video output S 6 AUDIOIN RCA connector for audio input 8 LAN Interface RJ45 10M 100M Ethernet interface ooo o RS 485 Interface Connector for RS 485 devices Connect the D and D terminals to T and T of PTZ receiver respectively
5. 39 User Manual of DS 7200 7300 8100 Series DVR Chapter 3 Live View 40 User Manual of DS 7200 7300 8100 Series DVR 3 1 Introduction of Live View Live view shows you the video image getting from each camera in real time The device automatically enters Live View mode when powered on It is also at the very top of the menu hierarchy thus pressing the ESC many times depending on which menu you re on brings you to the Live View mode Live View Icons In the live view mode there are icons at the right top of the screen for each channel showing the status of the record and alarm in the channel so that you can know whether the channel is recorded or whether there are alarms occur as soon as possible Table 3 1 Description of Live View Icons Alarm video loss tampering motion detection or sensor alarm a Terz Record manual recording continuous recording motion detection or sensor alarm triggered recording Alarm amp Record Event Exception motion detection sensor alarm or exception information For details see Chapter 8 6 Handling Exceptions E NOTE H Sensor alarm is supported by DS 7224 7232 DS 7300 DS 8100 and HDVR models only 4 User Manual of DS 7200 7300 8100 Series DVR 3 2 Operations in Live View Mode In live view mode the following functions can be realized Single Screen showing only one screen on the monitor Multi screen showing multiple screens on the
6. Call patrol in live view mode 58 User Manual of DS 7200 7300 8100 Series DVR Steps 1 Press PTZ control on the IR remote or click PTZ Control Wa on the quick setting toolbar to show the PTZ control toolbar 2 Choose Patrol on the control bar 3 Click the patrol you want to call PTZ mE Pee Sy recs re coom Configuration 1 Preset Patrol2 Patrol3 Patrol4 Figure 4 10 PTZ Toolbar Call Patrol Customizing Patterns Purpose Patterns can be set by recording the movement of the PTZ You can call the pattern to make the PTZ movement according to the predefined path Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Choose pattern number in the option box General Analog 1 O Save Preset TR ecg ees Pear e Call Preset sessiles lei a T5 TS TO T Wut ra lt P Pd gui g AN h n Hey N j x f N Pattern 1 8060 Patrol 4 Figure 4 11 PTZ Pattern 59 User Manual of DS 7200 7300 8100 Series DVR 3 Click and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera The movement of the PTZ is recorded as the pattern 4 Click to save the pattern Repeat the above steps to save more patterns Calling Patterns Purpose Follow the procedure to move the PTZ camera according to the predefined patterns Call pattern in the PTZ setting inte
7. Figure 6 21 4 ch Synchronous Playback Interface 3 Click the icon Es on the playback control toolbar and the record files will be played back reversely 115 User Manual of DS 7200 7300 8100 Series DVR Chapter 7 Backup 116 User Manual of DS 7200 7300 8100 Series DVR 7 1 Backing up Record Files Before you start Please insert the backup device s into the device 7 1 1 Quick Export Purpose Export record files to backup device s quickly Steps 1 Enter Video Export interface Menu gt Export gt Normal Analog B A1 A2 A3 A4 A5 IP Camera D1 D2 v A6 01 01 2013 00 00 23 12 23 2013 16 33 04 All All 12 23 2013 00 00 00 12 23 2013 23 59 59 Quick Export Search Figure 7 1 Quick Export Interface 2 Choose the channel s you want to back up and click Quick Export button mE The time duration of record files on a specified channel cannot exceed 24 hours Otherwise the message box Max 24 hours are allowed for quick export will pop up 117 User Manual of DS 7200 7300 8100 Series DVR Device Name Refresh Name Size Type Edit Date Delete Play 7 664MB New Folder Format Export Cancel Figure 7 2 Quick Export using USB1 1 3 In the Export interface choose backup device and click Export button to start exporting ES NOTE Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup devices supported by the device 4 Stay in th
8. Figure 9 30 RTSP Settings Interface 3 Enter the RTSP port in the text field of RTSP Service Port The default RTSP port is 554 and you can change it according to different requirements 4 Click the Apply button to save and exit the menu 161 User Manual of DS 7200 7300 8100 Series DVR 9 2 9 Configuring Server and HTTP Ports Purpose You can change the server and HTTP ports in the Network Settings menu The default server port is 8000 and the default HTTP port is 80 Steps 1 Enterthe Network Settings interface Menu Configuration Network 2 Select the More Settings tab to enter the More Settings interface Enter new Server Port and HTTP Port Alarm Host IP Alarm Host Port Server Port HIIP Port hull ICa cj P RTSP Port Figure 9 31 Host Others Settings Menu 4 Enter the Server Port and HTTP Port in the text fields The default Server Port is 8000 and the HTTP Port is 80 and you can change them according to different requirements 5 Click the Apply button to save and exit the interface NOTE The Server Port should be set to the range of 2000 65535 and it is used for remote client software access The HTTP port is used for remote IE access 9 2 10 Configuring HTTPS Settings Purpose HTTPS Hyper Text Transfer Protocol Secure ensures the data transferred is encrypted using Secure Socket Layer SSL or Transport Layer Security TLS HTTPS provides authentication of the web site and associat
9. GA 12VDC power supply POWER Switch for turning on off the device Ground needs to be connected when DVR starts up 22 User Manual of DS 7200 7300 8100 Series DVR DS 7232 The rear panel of DS 7232 1s shown in Figure 1 8 290093099 olo aa B B EB 00000000 idi Ln 990000000000 qome AUDIO OUT LAN RS 485 1 1 3 4 5 7 9 10 11 13 Figure 1 8 Rear Panel of DS 7232 mes The rear panel of DS 7224 provides 24 video input interfaces Z O 4 m Table 1 8 Description of Rear Panel 4 HDMI HDMlvidoouput 00000000 6 AUDIOIN RCAcomecorforaulioinput o 8 AlarmIwOut Connector for alarm input output o 9 LAN Interface RJ45 10M 100M 1000M Ethernet interface OUER for dd devices oan the D and D terminals to R and R terminals of PTZ receiver respectively POWER Switch for turning on off the device Ground needs to be connected when DVR starts up DS 7316 The rear panel of DS 7316 DVR is shown in Figure 1 9 9599 59995959595995959 05050506 05050208080 090959959999998990999090 000000000800090 58020259525959598050598 05050505 060806 080208029 0999969999999999999999099 0909959599999998989989898959 D J o9 O LJ B O509 5050 95050520 EN UE NM STERN FERES TEE 00909090909999099 cxxc xccx 09090909090909090 B55acnd D D EF PPP 123243678 Fwy ALARM IN 10 11 12 15 Figure 1 9 Rear Panel of DS 7316 c The rear panel of DS
10. NoTE The size of the currently selected files is displayed in the lower left corner of the window 2 Select record file s from the list and click Export button to enter the Export interface as shown in Figure 7 14 Event Details EIU C Record Time Size Play BA A1 07 22 2013 08 50 46 2 626KB HDD 1 Start time 07 22 2013 08 50 46 End time 07 22 2013 08 51 11 Total 2 P 1 1 Total size OMB Export All Export Cancel Figure 7 10 Event Details Interface 7 Export the selected record files Click the Export button and start backing up fore If the inserted USB device 1s not recognized Click the Refresh button Reconnect device Check for compatibility from vendor You can also format USB flash drive or USB HDDs via the device 123 User Manual of DS 7200 7300 8100 Series DVR USB1 1 v Refresh Folder 2012 05 16 09 40 54 Folder 2012 05 16 09 47 50 Folder 2012 05 16 09 47 58 Folder 2012 05 16 09 48 16 Folder 2012 05 23 12 02 30 1 117MB New Folder Format Export Cancel Figure 7 11 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop up message Export finished 8 Check backup result Choose the record file in Export interface and click button to check it fore The Player player exe will be exported automatically during record file export Device Name Refresh Name Size T
11. Select Menu gt Record gt Parameters gt Record and set the Frame rate to Full Frame 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from our company to do the further process When using the device to get the live view audio there is no sound or there is too much noise or the volume is too low Possible Reasons a Cable between the pickup and camera is not connected well impedance mismatches or incompatible b The stream type is not set as Video amp Audio c The encoding standard is not supported with device Steps 1 Verify the cable between the pickup and camera is connected well impedance matches and compatible 2 Verify the setting parameters are correct Select Menu gt Record gt Parameters gt Record and set the Stream Type as Audio amp Video 3 Verify the audio encoding standard of the camera is supported by the HDVR HDVR supports G722 1 and G711 standards and if the encoding parameter of the input audio is not one of the previous two standards you can log in the IPC to configure it to the supported standard 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from our company to do the further process The image gets stuck when HDVR is playing back by IPC Possible Reasons a Poor network between HDVR and IPC and ther
12. Steps 1 Enter Export interface Menu gt Export gt Event 2 Select Motion Alarm Input Line Crossing Detection or Intrusion Detection as the event type T NOTE The following steps have introduced the backup by motion detection triggered record files Perform the same operation for the backup by alarm triggered record files 121 User Manual of DS 7200 7300 8100 Series DVR 3 Set the start time and end time of the record files 4 Select the camera s for searching Motion 07 01 2013 00 00 00 12 24 2013 23 59 59 v Analog EX E A2 FX E A4 B A5 MAS iv A7 IP Camera D1 D2 Search Figure 7 8 Event Search for Backup 5 Click Search button to enter the Search Result interface Motion MSource Start Time End Time BA 07 22 2013 08 50 57 07 22 2013 08 51 05 BA 07 22 2013 10 26 05 07 22 2013 10 26 21 BA 07 22 2013 10 58 37 07 22 2013 10 58 43 Total 4 P 1 1 Pre p la Yy Post play Quick Export Details Cancel Figure 7 9 Result of Event Search 6 Select record files to export You can use the following two ways to enter the Export interface Select motion detection event s from the list and click Quick Export button to enter the Export interface as shown in Figure 7 14 1 Click the Details button to enter the interface with detailed information of the record file e g Start time end time file size etc 122 User Manual of DS 7200 7300 8100 Series DVR T
13. Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the General tab Working Mode Select NIC Figure 9 3 General Network Settings of DS 8116 8124 8132 Iria The DS 8116 8124 8132 models provide two 10M 100M 1000Mbps self adaptive network interfaces 3 Select the working mode Multi address Mode The parameters of the two NIC cards can be configured independently You can select LAN1 or LAN in Select NIC field for parameter settings You can select one NIC card as default route And when the system is connecting with the extranet the Net Fault tolerance 172 6 23 163 255 255 255 0 MEALS PE fe80 240 48ff fe94 580e 64 00 40 48 94 58 0e 1500 data will be forwarded through the default route 149 User Manual of DS 7200 7300 8100 Series DVR Multi address LAN1 10M 100M 1000M Self adaptive a 172 6 21 110 286 255 285 0 172 6 MES fe80 240 48ff fe 72 cc85 64 00 40 48 72 cc 85 1500 Figure 9 4 Multi address Working Mode Load Balance Mode By using the same IP address two NIC cards share the load of the total bandwidth which enables the system to provide two Gigabit network capacity Load Balance E 152 8 521 110 255 255 255 0 tie 215 00 40 48 72 cc 85 1500 Figure 9 5 Load Balance Working Mode Net Fault tolerance Mode The two NIC cards use the same IP address and you can select the Main NIC to LANI or LAN2 By this way in
14. GB 0 A Free Quota Space 931 GB Figure 10 14 Storage Mode Settings Interface 3 Enter the storage capacity in the text field of Max Record Capacity GB Mode Quota Camera Analog 1 Used Record Capacity 1 024MB HDD Capacity GB 931 Max Record Capacity GB 500 Free Quota Space 431 GB Figure 10 15 Configure Record Quota 4 You can copy the quota settings of the current camera to other cameras if required Click the Copy button to enter the Copy Camera menu as shown below Copy to E Analog SEE LEM DOES DOM Fe D NA E As WiP Camera MDi y Figure 10 16 Copy Settings to Other Camera s 5 Select the camera s to be configured with the same quota settings You can also click the checkbox of Analog to select all cameras 6 Click the OK button to finish the Copy settings and back to the Storage Mode interface 7 Click the Apply button to apply the settings T NOTE If the quota capacity is set to 0 then all cameras will use the total capacity of HDD for recording 180 User Manual of DS 7200 7300 8100 Series DVR 10 5 Checking HDD Status Purpose You may check the status of the installed HDDs on device so as to take immediate check and maintenance in case of HDD failure Checking HDD Status in HDD Information Interface Steps 1 Enter the HDD Information interface Menu gt HDD gt General 2 Check the status of each HDD which is displayed on the list a M1 931 51GB Normal
15. Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 LR LL Apply Figure 8 18 Set Arming Schedule of VCA Alarm Choose one day of a week and up to 8 time periods can be set within each day Click Apply to save the settings Time periods shall not be repeated or overlapped 3 4 Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days Select Linkage Action tab to set up alarm response actions of the alarm input please refer to Chapter 8 7 Setting Alarm Response Actions Click the OK button to complete the VCA alarm settings of the channel 6 Configure the region and other settings for the selected VCA detection Task1 Configure the Line Crossing Detection 1 2 Select the virtual line from the drop down list Up to 4 lines are selectable Select the direction to A lt gt B A gt B or A lt B 139 User Manual of DS 7200 7300 8100 Series DVR Figure 8 19 Set Direction of Line Crossing Detection 3 Setthe sensitivity of the line crossing detection to 1 100 4 Click and set two points in the preview window to draw a virtual line Analog 1 Line Crossing Detection BW a Figure 8 20 Draw Virtual Line in the Image You can use the E to clear the existing virtual line and re draw it 5 Click Apply to save the settings Task2 Confi
16. PTZ PTZ Camera Analog 1 Camera Analog 1 Camera Analog 1 Configuration E uw E mw One touch d E General gt E 4 One touch fy te Zoom Park Quick Patrol lt Joje ros Park Patrol 1 Configuration El oem 1 Call Patrol Stop Pa 1 Gog ce Speed Park Preset 1 Linear Scan Restore Call Patt Stop Pa 1 Figure 4 27 PTZ Panel Table 4 2 Description of the PTZ panel icons Roue Direction button and Zoom Focus l Zoom Focus Iris TN FUN W auto cycle button Speed of PTZ Light on off Wiper on off movement 3D Zoom Image Centralization B ow Switch to the Switch to the PTZ Switch to the general PTZ Control one touch control General 5 control interface settings interface interface Previous item Minimize windows 72 User Manual of DS 7200 7300 8100 Series DVR Chapter 5 Record Settings 73 User Manual of DS 7200 7300 8100 Series DVR 5 1 Configuring Encoding Parameters Purpose By configuring the encoding parameters you can define the transmission stream type the resolution and so on Before you start 1 Make sure that the HDD has already been installed If not please install a HDD and initialize it Menu gt HDD gt General lllLabel Capacity Status Property Type Free Space Gro Edit Del n E Figure 5 1 HDD General 2 Check the storage mode of the HDD 1 Click Advanced to check the storage mode of the HDD 2 If the HDD mo
17. Purpose The smart playback function provides an easy way to get through the less effective information When you select the smart playback mode the system will analyze the video containing motion or VCA information and mark it with green color on the playback process bar The filtering rule of record files and playback speed for the non related and related video can be configured on your demand The playback by smart search is not supported for IP cameras Steps 1 Enter the Smart Playback interface 2 Select a camera in the camera list and select a date in the calendar and click the button to play 3 Click the a on the toolbar to enter Smart Search mode The smart search toolbar appears at the bottom of the screen Sem at asss T i Figure 6 14 Draw Area for Smart Search 4 Click and drag the mouse to draw area s for smart search of VCA event or motion event Line Crossing Detection Click the N button and then click on the video display screen to specify the start point and end point of the line e Intrusion Detection Click the cii button and then specify 4 points to set a quadrilateral region for intrusion detection Only 109 User Manual of DS 7200 7300 8100 Series DVR one region can be set e Motion Detection Click the button and then click and draw the mouse to set the detection area manually You can also click the E button to set the full screen as the detection area 5 Click the a to
18. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 LJ E E 6 CG G6 eG For getting an accurate feedback result it is recommended to set the testin Copy Figure 11 6 Arming Schedule of VQD 5 Configure the linkage actions of video quality diagnostics alarm Settings Arming Schedule Full Screen Monitoring E Audible Warning Notify Surveillance Center Send Email Trigger Alarm Output KAlarm Output No Alarm Name E1Local gt 2 EALocal gt 3 P Were nd 1172 6 23 2 8000 7 1 Cancel Figure 11 7 Linking Actions of VQD 6 Configure the threshold of the three exception types Blurred Image Abnormal Brightness and Color Cast The value can be set to 0 100 When the actual value exceeds the configured threshold the video quality diagnostics alarm will be triggered and linked with the response actions 189 User Manual of DS 7200 7300 8100 Series DVR Analog 1 o Diagnost Threshold Blurred Bl Abnorm Color C Restore Figure 11 8 Image Settings Interface 7 Click Apply to save the settings You can click Copy to copy the settings to other analog cameras or click Restore to restore the values of the Blurred Image Abnormal Brightness and Color Cast to the default settings 190 User Manual of DS 7200 7300 8100 Series DVR Chapter 12 Device Management and Maintenance 191 User Manual of DS 7200 7300 8100 Series DVR 12 1 Viewing System Informati
19. 17 2013 18 17 12 All All 12 18 2012 00 00 00 12 18 2012 23 59 59 Quick Export Search Figure 5 36 Export 2 Select the channels by checking the checkbox to 3 Configure the record type file type and start end time 4 Click Search to show the results Search result Mca Start End Time Size Play Lock eo i HDD 4 Start time 12 18 2012 16 16 23 End time 12 18 2012 16 18 51 Total 1 P 1 1 Total size 0MB Export All Cancel Figure 5 37 Playback Search Result 96 User Manual of DS 7200 7300 8100 Series DVR 5 Protect the record files Find the record files you want to protect and then click the icon which will turn to 1 indicating that the file is locked ors The record files of which the recording is still not completed can t be locked 2 Click to change it as to unlock the file and the file is not protected Attention Record file may be overwritten after unlocking Continue Yes No Figure 5 38 Unlocking Attention Protect file by setting HDD property to Read only nore To edit HDD property you need to set the storage mode of the HDD to Group See Chapter 10 3 Managing HDD Group Steps 1 Enter HDD setting interface Menu gt HDD Figure 5 39 HDD General 2 Click A to edit the HDD you want to protect 97 User Manual of DS 7200 7300 8100 Series DVR Local HDD Settings HDD No HDD Property RAV Read only Redundancy Group LEM
20. 172 5 22 122 Figure 9 9 PServer Settings Interface DynDNS 1 Enter Server Address for DynDNS e g members dyndns org 2 In the Device Domain Name text field enter the domain obtained from the DynDNS website 3 Enter the User Name and Password registered in the DynDNS website 152 User Manual of DS 7200 7300 8100 Series DVR DynDNS members dyndns org 123 dyndns com test LAZZI Figure 9 10 DynDNS Settings Interface PeanutHull Enter User Name and Password obtained from the PeanutHull website PeanutHull 123 gicp net LXZXIIXI Figure 9 11 Peanut Hull Settings Interface NO IP Enter the account information in the corresponding fields Refer to the DynDNS settings Enter Server Address for NO IP 2 In the Device Domain Name text field enter the domain obtained from the NO IP website www no ip com 3 Enter the User Name and Password registered in the NO IP website NO IP no ip org 123 no ip org test LXZIIXIXZIXI Figure 9 12 NO IP Settings Interface HiDDNS You need to enter the Server Address and Device Domain Name for HiDDNS and other fields are read only 1 Enter the Server Address of the HiDDNS server www hik online com 2 Enter the Device Domain Name You can register the alias of the device domain name in the HiDDNS server first and then enter the alias to the Device Domain Name in the DVR you can also enter the domain name directly on the DVR to c
21. 8100 Series DVR 8 2 Setting Sensor Alarms SE Nore This section is available for DS 7224 7232 DS 7300 DS 8100 and HDVR models only Purpose You can set handling method of an external sensor alarm Steps 1 Enter Alarm Settings interface and select an alarm input Menu gt Configuration gt Alarm Alarm Input Alarm Output Alarm Input List Alarm Input No Alarm Name Alarm Type Local lt 2 N O Local lt 3 N O Local lt 4 N O Local lt 5 N O Local 6 N O acal 7 N O Alarm Output List Alarm Output No Alarm Name Dwell Time Local gt 2 5s Local gt 3 5s Local gt 4 5s Figure 8 7 Alarm Status Interface 2 Select Alarm Input tab to enter Alarm Input Settings interface and set the handling method of the selected alarm input Check checkbox to enable the alarm input and click to set up its alarm response actions Alarm Status Alarm Output Meer EM 1 N C e Figure 8 8 Alarm Input Settings Interface 3 Select Trigger Channel tab and select one or more channels which will start to record or become full screen monitoring when an external alarm is input Click Apply to save the settings 4 Select Arming Schedule tab to set the channel s arming schedule Choose one day of a week and up to eight time periods can be set within each day Set up arming schedule of other days of a week You can also use Copy to copy an arming schedule to other days Click Apply to save the settings 133 User Manual
22. Camera 06 Camera 07 Camera 08 Camera 09 Camera 10 Camera 11 Camera 12 Camera 13 Camera 14 Camera 15 Camera 16 Camera 17 Figure 3 8 Live View Camera Order To set the camera order 1 2 3 4 5 Click the View tab to enter the camera order settings interface Select an output interface and select a screen layout Click to select a screen in the right region and double click to select a channel in the left region Thus the selected channel will be displayed in the corresponding screen NOTE means the channel will not be displayed You can click to start live view of all channels and click wd to stop live view of all channels Click mai or to go to the previous or next page Click the Apply button to save the setting 49 User Manual of DS 7200 7300 8100 Series DVR 3 4 Channel zero Encoding Purpose Sometimes you need to get a remote view of many channels in real time from web browser or CMS Client Management System software in order to decrease the bandwidth requirement without affecting the image quality channel zero encoding is supported as an option for you Steps 1 Enter the Live View Settings interface Menu Configuration Live View 2 Select the Channel Zero Encoding tab General View Enable Ghannel Zero Enc Frame Rate 12fps Max Bitrate Mode General Max Bitrate Kbps 1024 Figure 3 9 Live View Channel Zero Encoding 3 Check the checkbox after Enable Channel Ze
23. Check 4 checkbox to select one channel for playback or select multiple channels for synchronous playback mE The max number of channels for synchronous playback supported varies to different models 104 User Manual of DS 7200 7300 8100 Series DVR Synch Playback E Analog Ve FV KNEES LU MA10 Figure 6 7 Select Channels for Synchronous Playback 6 Event playback interface The toolbar in the bottom part of Playback interface can be used to control playing process 8 Event s Hox Start Time Play 6 3 16 57 30 16 58 31 16 59 30 17 00 15 17 01 32 17 01 44 17 01 58 17 02 52 17 03 10 17 03 30 17 03 39 17 04 00 17 04 10 17 04 30 17 04 40 17 05 00 17 05 10 17 05 30 17 05 40 17 05 59 Uri NY 3239999999099909 909999 90993999 Total 96 P 1 1 Preplay 305 Post play 30s Back db m iN vi Figure 6 8 Interface of Playback by Event Pre play and post play can be configured for the playback of event triggered record files Pre play The time you set to play back before the event For example when an alarm triggered the recording at 10 00 if you set the pre play time as 5 seconds the video plays back from 9 59 55 Post play The time you set to play back after the event For example when an alarm triggered the recording ends at 11 00 if you set the post play time as 5 seconds the video plays back till 11 00 05 105 User Manual of DS 7200 7300 8100 Series DVR Figure 6
24. Continuous o 0 6 6 6 6 6 O Cancel Figure 5 18 Edit Schedule Motion Detection 3 In the message box you can choose the day to which you want to set schedule 4 Setthe Type as Motion 5 To schedule an all day recording check the checkbox after the All Day item 6 To arrange other schedule leave the All Day checkbox blank and set the Start End time fore Up to 8 periods can be configured for each day And the time periods can t be overlapped each other Repeat the above steps3 6 to schedule motion detection triggered recording for all the week If the schedule can also be set to other days click Copy 84 User Manual of DS 7200 7300 8100 Series DVR Copy to v p E vE vE 7 g Holiday Figure 5 19 Copy Schedule to Other Days 7 Click OK to back to upper level menu If you can to copy the same schedule settings to other camera s click Copy to enter the Copy Camera interface and then select the camera s you want to copy Copy to v Analog A1 BA GAS BAs GAS GAG MAT GAs EIP Camera PIE py Figure 5 20 Copy Schedule to Other Channels 85 User Manual of DS 7200 7300 8100 Series DVR 5 4 Configuring Alarm Triggered Record a Nore This section is available for DS 7224 7332 DS 7300 DS 8100 and HDVR models only Purpose Follow the procedure to configure alarm triggered recording Steps 1 Enterthe Alarm setting interface Menu gt Configuration gt Alarm Alarm Status Ala
25. DS 7200 7300 8100 Series DVR IP Camera Import Export MCameraNo Add Delete Status IP Camera Address Edit Upgrade Camera Name D1 gt 172 6 23 3 A Camera 01 MD2 TT 172 6 23 124 Fi E Camera 01 Refresh Upgrade Delete Add All Custom Adding Figure 2 14 Successfully Added IP Cameras 3 Import Export the configuration file of the IP cameras Import the configuration file of IP cameras to the device Connect the backup device on which the configuration file is stored 1 Click the IP Camera Import Export tab IP Camera Device Name Refresh Name Size Type Edit Date Del Play il gt Free Space 7 664MB New Folder Import Figure 2 15 Import IP Camera Configuration File 2 Select the backup device from the drop down list and you can click the Refresh button to get the latest information of the backup device 3 Select the configuration file of IP camera from the list 4 Click the Import button to import the IP cameras to the device 5 Click OK on the pop up message box after the importing process is complete The imported IP cameras will be displayed on the IP Camera Management interface Export the configuration file of IP cameras to backup device Connect the backup device on which the configuration file is stored to the device 37 User Manual of DS 7200 7300 8100 Series DVR Click the IP Camera Import Export tab IF Camera Device Name SE 1 Refresh Name Size Type Edit Dale Delete Play
26. E4 C series PAL NTSC adaptive video inputs H 264 video compression with high reliability and superior definition Encoding at up to 4CIF resolution for DS 7204 7208 7216HVI SH DS 7200HFI SH DS 7300HFI SH and DS 8100HFSI SH models and up to WD1 PAL 960x576 NTSC 960x480 resolution for other models Each channel supports dual stream Independent configuration for each channel including resolution frame rate bit rate image quality etc Input and output video quality is configurable Normal and event recording parameters configurable per individual camera Encoding for audio video composite stream or video stream audio and video synchronization during composite stream encoding Watermark technology Video quality diagnostics Local Monitoring simultaneous HDMI VGA and CVBS outputs HDMI VGA output at up to 1920x1080P resolution 1 4 6 8 9 16 25 36 division live view is supported and the display sequence of screens is adjustable Manual or auto switch of cameras in live view with the dwell time is configurable Quick setting menu is provided for live view The selected live view channel can be shielded Motion detection video tampering video exception video loss and VCA alarm functions NOTE The VCA alarm type is supported by the Smart DVR HDVR models only Privacy mask Multiple PTZ protocols supported setting and calling of PTZ preset patrol and pattern Zooming in by clicking the mouse and PTZ tra
27. HDD is error or not detected Steps 1 Verify the system time setting is correct Select Menu gt Configuration gt General gt General and verify the Device Time is correct 2 Verify the search condition is correct Select Playback and verify the channel and time are correct 3 Verify the HDD status is normal Select Menu gt HDD gt General to view the HDD status and verify the HDD is detected and can be read and written normally 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from our company to do the further process 0301001040612 217
28. JOG SHUTTLE Control DS 8100 Enter letters WXYZ Multi camera display in live view In Playback mode or MenuPlayback gt Tag playback interface this button can be used to delete the selected tag Enter numeral 0 Switch between input methods upper and lowercase alphabet symbols and numeric input In Playback mode this button can be used to add the default tag The DIRECTION buttons are used to navigate between different fields and items in menus In Playback mode the Up and Down button is used to speed up and slow down recorded video In All day Playback mode the Left Right button can be used to select the recorded video of next previous day in Playback by Normal Video Search the Left Right button can be used to select the next previous recorded file In Live View mode the directional buttons can be used to cycle through channels In PTZ control mode it can control the movement of the PTZ camera Confirm selection in any of the menu modes It can also be used to tick checkbox fields In Playback mode it can be used to play or pause the video In Single frame Playback mode pressing the ENTER button will advance the video by a single frame In Auto switch mode it can be used to stop start auto switch Move the active selection in a menu The inner ring will move the selection up and down the outer ring will move it left and right In Playback mode the inner ring is used to jump 30s forward backwa
29. PEE FEE CEE LM LEE NAME ED LAE ELDE BAM RPM EFE RUM BL Mo HDD Capacity 931 51GB Cancel Figure 5 40 HDD General Editing 3 Set the HDD to Read only 4 Click OK to save settings and back to the upper level menu fore You can t save any files in a Read only HDD If you want to save files in the HDD change the property to R W fore If there is only one HDD and is set to Read only the device can t record any files Only live view mode is available If you set the HDD to Read only when the device is saving files in it then the file will be saved in next R W HDD If there is only one HDD the recording will be stopped 98 User Manual of DS 7200 7300 8100 Series DVR Chapter 6 Playback 99 User Manual of DS 7200 7300 8100 Series DVR 6 1 Plaving Back Record Files 6 1 1 Playing Back by Channel Purpose Play back the recorded video files of a specific channel in the live view mode Channel switch is supported Instant Playback by Channel Steps Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar E Only record files recorded during the last five minutes on this channel will be played back f Figure 6 1 Instant Playback Interface All day Playback by Channel Enter the All day Playback interface Mouse right click a channel in live view mode and select Playback from the menu as shown in Figure 6 2 100 User Manual of DS 720
30. PPPoE Settings Interface Check the PPPoE checkbox to enable this feature Enter User Name and Password for PPPoE access T The User Name and Password should be assigned by your ISP Enable PPPOE User Name test rere ee Password Figure 9 17 PPPoE Settings Interface Click the Apply button to save and exit the interface After successful settings the system asks you to reboot the device to enable the new settings and the PPPoE dial up is automatically connected after reboot You can go to Menu gt Maintenance gt System Info gt Network interface to view the status of PPPoE connection Please refer to Chapter 12 1 Viewing System Information for PPPoE status 9 2 3 Configuring NTP Server Purpose A Network Time Protocol NTP Server can be configured on your device to ensure the accuracy of system date time Steps 1 Enter the Network Settings interface 2 Menu gt Configuration gt Network Select the NTP tab to enter the NTP Settings interface 155 User Manual of DS 7200 7300 8100 Series DVR Enable NTP Interval min 60 210 72 145 44 123 Figure 9 18 NTP Settings Interface 3 Check the Enable NTP checkbox to enable this feature 4 Configure the following NTP settings Interval Time interval between the two synchronizing actions with NTP server The unit is minute NTP Server IP address of NTP server e NTP Port Port of NTP server 5 Click the Apply button to save and exit the in
31. STATES THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU User Manual of DS 7200 7300 8100 Series DVR Regulatory information FCC information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two c
32. ates I MR ates MM MM 22 1 6 Starting Up and Shutting Down the Device esses 28 Chapter 2 Getting Started 3 eter o aeta esos o aseo eaae ao aao adeo sese a esa uaa dea sese aera ue ades 29 2 1 Using the Wizard for Basic Configuration ccccccccccccccceceeeeesessssseeeeeeeeees 30 22 Adding and Connecting the IP Cameras cccccccccccccceeeeeeeeeesesseeseeeeeeeees 35 21 Addune the IP Cameras 25d icone thtteide he Seide oco nide cHD trc hon ie EE Dod de tu ed decuit 35 2 2 2 Contisurme the Connected IP Cameras v er rode oes 38 Chapter 5 Live VIQGW aues eve se HS SUE S TAE ses cease HIVE REIN HAITI vU I T Soie 40 3 introduction Or Lave VieW areenan odo e avo e aui Ue ai 4 3 2 Operations in Live View Mode oni deir o Lose PI idee In ooa Hove dh tese oin 42 3 2 1 Front Patel One rauOns sucus ico De OE BE p OHNE REID Ea 42 3 2 2 Usine the Mouse 1n E1Ve VIEW enra edem el adc voe ides 42 312 3 Using an Auxiliary MOBIDOL ici tiii rer bte bo HER e REPE Le Edo tirado ted 43 3 2 4 Main Aux Output Switching sorser a 44 3 2 5 Quick Setting Toolbar in Live View Mode eeeeeeeeeeeeeeeee 44 3 3 Contisurine Live View Seiho Steenis nor o Ot RUNE e be eb atn 48 3 4 Cha nticbzero NCO CNG seo I toe en etate ea IAE ae ona 50 3 5 Manual Video Quality Diagnostics esses 50 3 6 gio og 6 00 emer te Tr E A 32 Chapter Su ABIRE TOTO Tm 53 4 1 Contig urin amp P TZ Se
33. cannot be formatted Device Name Name Size Type 7 664MB New Folder 120 Edit Date Format Refresh Delete Play Cancel Figure 7 6 Export by Normal Video Search using USB Flash Drive Export User Manual of DS 7200 7300 8100 Series DVR Stay in the Exporting interface until all record files are exported with pop up message box Export finished 5 Check backup result Choose the record file in Export interface and click button to check it fore The Player player exe will be exported automatically during record file export Device Name Refresh Name Size Type Edit Date Delete Play EH a01_md_ch01_ 130 2 626KB File 07 23 2013 10 17 28 T g8 it B ch01_20130722084 22KB File 07 22 2013 17 13 00 T ch01_20130722084 22KB File 07 22 2013 17 13 00 T player exe 786KB File 07 23 2013 10 17 28 T 7 660MB New Folder Format Cancel Figure 7 7 Checkup of Export Result using USB Flash Drive 7 1 3 Backing up by Event Search Purpose Back up event related record files using USB devices USB flash drives USB HDDs USB writer SATA writer or eSATA HDD Quick Backup and Normal Backup are supported a Nore X Backup by alarm input search is supported by DS 7224 7232 DS 7300 DS 8100 and HDVR models only Backup by VCA Line Crossing Detection or Intrusion Detection search is supported by the Smart DVR HDVR only The eSATA writer is supported by DS 7300 and DS 8100 models only
34. connecting status of device through the network detection function including network delay packet loss etc 9 4 1 Testing Network Delay and Packet Loss Steps 1 Enter the Network Traffic interface Menu gt Maintenance gt Net Detect 2 Click the Network Detection tab to enter the Network Detection menu Traffic Network Stat Network Delay Packet Loss Test LAN1 Network Packet Export i Refresh LAN1 172 6 24 64 Export Figure 9 40 Network Detection Interface Enter the destination address in the text field of Destination Address Click the Test button to start testing network delay and packet loss The testing result pops up on the window If the testing is failed the error message box will pop up as well Result Attention Average delay 1 ms Mau Packet loss rate 0 The destination is unreachable Figure 9 41 Testing Result of Network Delay and Packet Loss 9 4 2 Exporting Network Packet Purpose By connecting the device to network the captured network data packet can be exported to USB flash disk and other local backup devices Steps 1 Enter the Network Traffic interface Menu gt Maintenance gt Net Detect 2 Click the Network Detection tab to enter the Network Detection interface 167 User Manual of DS 7200 7300 8100 Series DVR 3 Select the backup device from the dropdown list of Device Name En NOTE Click the Refresh button if the connected local backup device cannot be
35. end time for search 3 Select the major type of the log from the drop down list 4 major types are selectable Alarm Exception Operation and Information 4 Check the checkboxes to select the minor type of the log for search 5 Click Search and the logs matching the search conditions will be displayed on a list 111 User Manual of DS 7200 7300 8100 Series DVR Log Export Start Time 07 18 2013 End Time 07 18 2013 Major Type All MMinor Type MLocal Operation Upgrade Local Operation Start Recording Local Operation Stop Recording MALocal Operation PTZ Control Local Operation Lock File Major Type T Operation 07 18 2013 08 53 23 Information 07 18 2013 08 53 25 Exception 07 18 2013 08 53 25 amp Alarm 07 18 2013 08 53 27 amp Alarm 07 18 2013 08 53 28 AY AS ban Ew ee hi oe AF AM AMAN aTa TT Sa Eia Ea Total 973 P 1 10 00 00 00 23 59 59 Minor Type Local Operation Start Recording Record Capture Start Motion Det Start Motion Det A sms s lan am una mdi m am v Paramet Play Details N A v N A NiA N N LESEN Search Figure 6 17 Result of System Log Search 6 Select a log with record file and click button to enter Playback interface i NOTE If there is no record file at the time point of the log the message box No result found will pop up Playback Figure 6 18 Interface of Playback by Log 6 1 7 Playing Back External F
36. is provided by DS 7300 and DS 8100 models only Purpose The RS 232 port can be used in two ways e Parameters Configuration Connect a PC to the device through the PC serial port Device parameters can be configured by using software such as HyperTerminal The serial port parameters must be the same as the device s when connecting with the PC serial port e Transparent Channel Connect a serial device directly to the device The serial device will be controlled remotely by the PC through the network Steps 1 Enter the RS 232 Settings interface Menu gt Configuration gt RS 232 115200 8 1 None None Console Figure 13 2 RS 232 Settings Interface 2 Configure RS 232 parameters including baud rate data bit stop bit parity flow control and usage 3 Click Apply to save the settings 201 User Manual of DS 7200 7300 8100 Series DVR 13 3 Configuring DST Settings Steps 1 Enter the General Settings interface Menu Configuration General 2 Choose DST Settings tab General More Settings E Auto DST Adjustment Apr 1st Oct v last 60 Minutes Figure 13 3 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item Or you can manually check the Enable DST checkbox and then set the date of the DST period 202 User Manual of DS 7200 7300 8100 Series DVR 13 4 Configuring More Settings Steps 1 Enter the General Settings interface Menu Configuration Gener
37. linear scan you can click the Linear Scan button again on the panel 6 Youcan click the Restore button and then reboot the PTZ camera to clear the limit points information PTZ Camera Analog 1 Configuration El Aw e 4 PTZ Control Park Quick Patrol Park Patrol 1 Park Preset 1 Restore Figure 4 25 Control Panel Call Linear Scan 4 2 3 One touch Park Purpose The one touch park function allows the PTZ camera to start a predefined action park action scan preset pattern etc automatically after a period of inactivity park time Steps 1 Click the button MMES in the lower right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting toolbar during the live view process or click PTZ Control on the right click menu to open the PTZ control panel in live view mode 2 Select the PTZ camera from the drop down list for control 3 Click the icon I on the panel and then click the One touch tab to enter the One touch control interface 70 User Manual of DS 7200 7300 8100 Series DVR 4 There are 3 one touch park types selectable Click the corresponding button to activate the park action Park Quick Patrol The PTZ camera starts the quick patrol from preset 1 to preset 32 in order automatically after the park time The undefined preset will be skipped Park Patrol 1 The PTZ camera moves according to the path of predefined patrol 1 after the
38. motion detection area click Clear 82 User Manual of DS 7200 7300 8100 Series DVR Camera Analog 1 Enable Motion Detection Full Screen Clear Figure 5 15 Motion Detection Mask 4 Click the beside Settings and the message box for channel information will pop up Settings Arming Schedule Linkage Action E Analog VP T Y FX Tee DOM P HA7 EAs WIP Camera HD1 Cancel Figure 5 16 Motion Detection Handling Nore The IP Camera is supported by HDVR series only 5 Select the channels which you want the motion detection event to trigger recording 6 Click Apply to save the settings 7 Click OK to back to the upper level menu 8 Exit the Motion Detection menu 3 Enter Schedule settings interface Menu Parameters Schedule 83 User Manual of DS 7200 7300 8100 Series DVR ti NOTE Analog 1 pe 8 1 14 16 Edit Continuous Event Motion Alarm ERES LEE VCA None Figure 5 17 Record Schedule The VCA recording type is supported by the Smart DVR HDVR series only 1 Check the checkbox after the Enable Schedule item 2 Click Edit Weekday All Day Start End Time otari End Time Start End Time Start End Time Start End Time Start End Time start end Time Start End Time a 00 00 11 00 17 00 20 00 12 00 14 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Motion Motion Motion Continuous Continuous Continuous Continuous Continuous
39. o Play hide 99 6 1 Playme Back Record Biles s op p LU RU Op TIE dc ACIE eis 100 6 1 1 Playine Back by C hdBfieTuuui ses nnn een Ete NO Ie ERU DeEEE DOE IER Pede ie 100 6 1 2 Playing Back Dy DIO do op ouo oA Potes ebat hu ot o iato oot 103 6 1 3 Playing Back Dy Event Seance trices on een ec Gr EE I e uda 103 6 1 4 Playine Back Dy T3985 oasis b E Eo RR UE t EDT Hb rs 106 6 1 5 Playing Back by Spiart Seatcli uoi ee e te e t at 109 6 1 6 Playine Back Dy SyStemoLOE 4incdosc esce de doa A i dins 111 6 1 7 Playing Back Bxterndl PIleSuuc deseo E p RERO ORCI aU 112 6 2 Auxiliary Punc oris oE Playback io c s oc LE ore ha t eid 114 0 2 1 Playing Back brame Dy Brame soe e o Ede e Pe pos cha tup Pe sen cedes 114 6 2 2 Dieital ZOOEDD mias heec tener cadi i ode th ca ie i tedde tuos td docto Mte poe du d go dete S adore 114 0 2 5 Reverse Playback of Multi channel a c eret ero RE red die eines 115 Chapter 7 Backup ounces evi e r ses evi TU NT UI 116 7 1 Backing Up Record Billet KD eau eii em 117 FATE OUICK EX DOL aasre aA E i 117 7 1 2 Backing up by Normal Video Searc Ws uiu ERE De ER 118 7T T 5 Backuie Up DY Event Seal ye dati dq vertus Hep THREE Adr VRAC OU LE 121 JU packs Up VIdeo CDS cesi top ERU RIEN Etpe JA De ERN PIE LUI maa Sb Melde aud 124 7 2 Manasine Backup Devices susce et Seton Pete o eb tu feel enced 127 Chapter Alarm Settlb9s ss sesvscascesiessssaasswanscivscausarsvacndatvesauvessseiassiusssuveseseiaseiussauvesesstaseau
40. park time Park Preset 1 The PTZ camera moves to the location of predefined preset 1 after the park time 5 Click the button again to inactivate the corresponding park action PTZ Camera Analog 1 Configuration E Hw e 4 PTZ Control b Park Quick Patrol Park Patrol 1 Park Preset 1 Linear Scan Restore Figure 4 26 Control Panel One touch Park E Nore The park time can only be set through the local menu of PTZ camera and the default value is 5s 4 2 4 PTZ Control Panel To enter the PTZ control Panel the following 3 ways are selectable Optionl In the PTZ settings interface click the PTZ button on the lower right corner Option2 In the Live View mode you can press the PTZ Control button on the front panel or on the remote control or click the PTZ Control icon Ll in the quick setting toolbar or click PTZ Control on the right click menu to enter the PTZ control panel Option3 In the live view mode use the mouse to right click on the window to access the right click menu and select the PTZ control option Click the Configuration button on the panel and you can enter the PTZ Settings interface s NOTE In PTZ control mode the PTZ panel will be displayed when a mouse is connected with the device If no mouse is connected the EI icon appears in the lower left corner of the window indicating that this camera is in PTZ control mode 71 User Manual of DS 7200 7300 8100 Series DVR PTZ
41. password 3 Verify the whether the bandwidth is enough 1 Select Menu gt Maintenance gt Net Detect gt Network Stat 2 Check the usage of the access bandwidth and see if the total bandwidth has reached its limit 4 Check if the fault is solved by the step 1 to step 3 If it is solved finish the process If not please contact the engineer from our company to do the further process The IPC frequently goes online and offline and the status of it displays as Disconnected Possible Reasons a The IPC and the HDVR versions are not compatible b Unstable power supply of IPC c Unstable network between IPC and HDVR d Limited flow by the switch connected with IPC and HDVR Steps 1 Verify the IPC and the HDVR versions are compatible 1 Enter the IPC Management interface Menu gt Camera gt Camera gt IP Camera and view the firmware version of connected IPC 2 Enter the System Info interface Menu gt Maintenance gt System Info gt Device Info and view the firmware version of HDVR 2 Verify power supply of IPC is stable 1 Verify the power indicator is normal 214 User Manual of DS 7200 7300 8100 Series DVR 2 When the IPC is offline please try the ping command on PC to check if the PC connects with the IPC 3 Verify the network between IPC and HDVR is stable 1 When the IPC is offline connect PC and HDVR with the RS 232 cable 2 Open the Super Terminal use the ping command and keep sendi
42. search and then the result will be displayed as m in the progress bar of the Smart Playback interface Or you can click the E button to clear all the set areas 6 Click the b button to play Camera 02 Camera 03 Camera 04 Camera 05 Camera 06 Camera 07 Camera 08 Camera 09 Camera 10 Camera 11 ie Camera 12 Camera 13 Camera 14 Normal Event Smar Figure 6 15 Smart Playback Interface NOTE X Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames About video type bar B represents normal recording manual or schedule B represents event recording B represents smart search recording Table 6 2 Detailed Explanation of Smart Playback Scaling Process bar up down the Video type picture time line 110 User Manual of DS 7200 7300 8100 Series DVR 6 1 6 Playing Back by System Log Purpose You can also play back record file s after searching system logs Steps 1 Enter Log Information interface Menu gt Maintenance gt Log Information gt Log Search Log Export 12 23 2013 00 00 00 12 23 2013 23 59 59 Major Type All EAMinor Type MAlarm Output Start Motion Detection Stop Motion Detection Start Video Tampering Detection L La FT Sida aw Taunan auma Pale i No Major Type Time Minor Type Paramet Play Details Total 0 P 1 1 Search Figure 6 16 Log Search Interface 2 Specify the start time and
43. the checkbox of corresponding HDD and click the Init button 3 Verify the HDD is detected or is in good condition 1 Select Menu HDD General 2 Ifthe HDD is not detected or the status is Abnormal please replace the dedicated HDD according to the requirement 213 User Manual of DS 7200 7300 8100 Series DVR 4 Check if the fault is solved by the step 1 to step 3 1 fitis solved finish the process 2 Ifnot please contact the engineer from our company to do the further process The status of the added IPC displays as Disconnected when it is connected through the protocol of our company Select Menu gt Camera gt Camera gt IP Camera to get the camera status Possible Reasons a Network failure and the DVR and IPC lost connections b Theconfigured parameters are incorrect when adding the IPC Steps 1 Verify the network is connected 1 Connect the HDVR and PC with the RS 232 cable 2 Open the Super Terminal software and execute the ping command Input ping IP e g ping 172 6 22 131 a ai nore Simultaneously press Ctrl and C to exit the ping command If there exists return information and the time value is little the network is normal 2 Verify the configuration parameters are correct 1 Select Menu gt Camera gt Camera gt IP Camera 2 Verify the following parameters are the same with those of the connected IP devices including IP address protocol management port user name and
44. to Normal or Motion Detection 33 User Manual of DS 7200 7300 8100 Series DVR Wizard Camera Analog 1 lll Start Recording IIo HT i 210 109 EL l I Previous Figure 2 9 Record Settings 4 Click Copy to copy the record settings of the current camera to other camera s if needed as shown in Figure 2 10 Copy to lll Analog Vee LEM LTEM LEONES FU LYAEM LUEEM LUNES LAUNE LXVEEE Li LEXKEM SCEE ES Lu Figure 2 10 Copy Record Settings 5 Click OK to return to the Record Settings window 13 Click OK to complete the startup Setup Wizard 34 User Manual of DS 7200 7300 8100 Series DVR 2 3 Adding and Connecting the IP Cameras uc This Chapter is available for the HDVR models only 2 2 1 Adding the IP Cameras Purpose The HDVR series can be connected with the network cameras and record the video from them Before you can get a live view or record of the video you should add the network cameras to the connection list of the device Before you start Ensure the network connection is valid and correct For detailed checking and configuring of the network please see Chapter 9 1 Configuring General Settings Chapter 9 3 Checking Network Traffic and Chapter 9 4 Network Detection Steps 1 Enter the Camera Management interface Menu Camera Camera Es P 5 Playback Manual Record 2 NCC 2 Camera Configuration Maintenance Shutdown Figure 2 11 Main Menu 2 Add the online came
45. to the Smart Coaxitron HDVR and Smart DVR HDVR series Purpose Follow the procedure to set the parameters for PTZ The configuring of the PTZ parameters should be done before you control the PTZ camera Before you start Make sure that the PTZ camera and the device are connected properly via RS 485 interface Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ Analog 1 Clear All Clear All Stop Clear All inear Scan Left Limit Right Limit RS 485 Setti Figure 4 15 PTZ Settings 2 Select the camera for PTZ setting from the drop down list 3 Click the RS 485 Settings button and then configure the RS 485 parameters of the device 4 Enter the parameters of the PTZ camera 62 User Manual of DS 7200 7300 8100 Series DVR Baud Rate Data Bit Stop Bit Parity Flow Ctrl PTZ Protoco Address Address range 0 255 RS 485 Settings 9600 8 1 None None HIKVISION 0 Cancel Figure 4 16 RS 485 Settings All the parameters should be exactly the same as the PTZ camera parameters Only PTZ Protocol can be configured for network cameras Example If the PTZ camera has a Baud rate as 115200 you should input 115200 in the Baud Rate field mE For the DS 7200HWI E1 2 C DS 7300HWI E4 C and DS 8100HWI E4 8 C series select the PTZ protocol to HIKVISION C Coaxitron or PELCO C Coaxitron Make sure the protocol selected here is supported by the connected camera When the Coax
46. 0 00 00 00 test Guest 00 00 00 00 00 00 test02 Operator 00 00 00 00 00 00 Figure 13 7 Added User Listed in User Management Interface 5 Select the user from the list and then click chelidbutton to enter the Permission settings interface Permission Remote Configuration Camera Configuration EA Local Log Search Local Parameters Settings El Local Camera Management El Local Advanced Operation Local Shutdown Reboot Cancel Figure 13 8 User Permission Settings Interface unda NoTE Local Camera Management is supported by HDVR series 6 Setthe operating permission of Local Configuration Remote Configuration and Camera Configuration for the user Local Configuration e Local Log Search Searching and viewing logs and system information of device e Local Parameters Settings Configuring parameters restoring factory default parameters and importing exporting configuration files 205 User Manual of DS 7200 7300 8100 Series DVR Local Camera Management Enabling and disabling analog camera s Adding deleting and editing of network camera s This function is supported by HDVR series Local Advanced Operation Operating HDD management initializing HDD setting HDD property upgrading system firmware clearing I O alarm output Local Shutdown Reboot Shutting down or rebooting the device Remote Configuration Remote Log Search Remotely viewing logs that are saved on the device Remote Parameters Se
47. 0 7300 8100 Series DVR Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch Start Recording Add IP Camera Quick Settings Playback PTZ Control Aux Monitor Figure 6 2 Right click Menu under Live View m The Add IP Camera item is available for the HDVR only Press PLAY button on the IR remote control to play back record files of the channel under single screen live view Under multi screen live view record files of the selected channel will be played back n ore Pressing numerical buttons will switch playback to the corresponding channels during playback process Playback Management The toolbar in the bottom part of Playback interface can be used to control playing progress as shown in Figure 6 3 101 User Manual of DS 7200 7300 8100 Series DVR Normal 3 x Max Ca Min Ca a ilCamera 02 llCamera 03 Camera 04 BiPCamera 01 Felele E mv Figure 6 3 Playback Interface Check the checkboxes to select the channel s and then the video from the selected channels will be played back synchronously Up to 16 channels can be set for synchronous playback Click the Max Camera for Playback tab and you can play back the video from 16 channels at a time Click the Min Camera for Playback tab and you can play back the video from only one channel Dates marked in different colors No record files in this day There is record file s in this day not current day There is even
48. 0623092323 BH ch03 20110623113325 B ch03_201 10623132800 ch03_20110623134743 player exe L ULL EE TEE S S ee Folder Folder OKB File OKB File 267MB File 280MB File 4 423KB File 127MB File 110MB File 18 36 7KB File 31 305KB File 608KB File visitor ot 150MB 06 23 2011 20 07 22 06 23 2011 20 07 28 06 23 2011 20 07 58 06 23 2011 20 07 36 06 23 2011 20 15 02 06 23 2011 20 11 14 06 23 2011 20 11 20 06 23 2011 20 1 06 23 2011 20 12 54 06 23 2011 20 13 02 06 23 2011 20 13 12 06 23 2011 20 09 40 MAME NA ANAA 44 2 AO Refresh lt e E O E d E 6 gt e fm gt Figure 7 18 Management of USB Writers and DVD R W 2 Select a record file folder picture in the backup device click the icon m and you can delete it Select a record file picture click the icon g and then you can play and view the video picture For USB Flash Drives USB HDDs and eSATA HDDs Click the button New Folder and you can create a new folder in the backup device Click the button Format and you can format the backup device Two kinds of file system can be configurable including FAT32 and NTFS For USB Writers and DVD R W User Manual of DS 7200 7300 8100 Series DVR Click the button Erase and you can erase the files from a re writable CD DVD s Nore If the inserted device is not recognized you can perform the following steps Click the button Refresh Reconnect device Check for
49. 1 1 Playing Back by Channel for the playback interface and toolbar description 6 1 3 Playing Back by Event Search Purpose Play back record files on one or several channels searched out by restricting event type motion detection or alarm input Channel switch is supported 103 User Manual of DS 7200 7300 8100 Series DVR NOTE Playback by alarm input search is supported by DS 7224 7232 DS 7300 and DS 8100 models only Steps 1 Enter the playback interface Menu gt Playback 2 Click and select to enter the Event Playback interface 3 Select Alarm Input Motion Line Crossing Detection or Intrusion Detection as the event type and specify the start time and end time for search E NOTE The line crossing detection or intrusion detection search is supported by the Smart HDVR DVR only Type Motion Camera MACamera 02 Camera 03 Iv Ter nu TE 04 v ade TE 01 Start Time 06 18 2014 00 00 00 End Time 06 18 2014 23 59 59 Q Search Figure 6 6 Video Search by Motion Detection 4 Click Search and the record files matching the search conditions will be displayed on a list 5 Select and click button to play back the record files You can click Back to return to the search interface If there is only one channel triggered clicking button takes you to Full screen Playback interface of this channel If several channels are triggered clicking button takes you to the synch playback interface
50. 12 60 21 31 Active Refresh Figure 9 24 UPnP Settings Finished Manual Manual Mapping If your router does not support the UPnP function perform the following steps to map the port manually in an easy way Before you start Make sure the router support the configuration of internal port and external port in the interface of Forwarding Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the NAT tab to enter the port mapping interface 3 Leave the Enable UPnP checkbox unchecked 4 Click LA to activate the External Port Settings dialog box Configure the external port No for server port http port RTSP port and https port respectively E NOTE The value of the RTSP port No should be 554 or between 1024 and 65535 while the value of the other ports should be between and 65535 and the value must be different from each other If multiple devices are configured for the UPnP settings under the same router the value of the port No for each device should be unique External Port Settings HTTP Port 81 Figure 9 25 External Port Settings Dialog Box 5 Click OK to save the setting for the current port and return to the upper level menu 6 Click Apply button to save the settings 7 Enter the virtual server setting page of router Input the internal port value in the Internal Source Port text field the external port value in the External Source Port text field a
51. 200 7300 8100 Series DVR In PTZ control settings press the REC button and then you can call a IEEE PTZ preset by pressing Numeric button VOIP MON Button Selecting all items on the list In live view or playback mode it can be used to switch between main and auxiliary video output MENU Button Back to the Main menu after successful login PREV Button Switching between single screen and multi screen mode and 30s forward In live view mode these buttons can be used to cycle through channels PTZ Button Enter the PTZ Control mode ESC Button Back to the previous menu Pressing for arming disarming the DVR in Live View mode F1 Button Selecting all items on the list when used in a list field In PTZ Control mode it will turn on off PTZ light PTZ Control Buttons Adjusting the iris focus and zoom of a PTZ camera F2 Button Cycle through tab pages Troubleshooting Remote Control ju Make sure you have installed batteries properly in the remote control And you have to aim the remote control 12 DIRECTION ENTER Navigating between different fields and items in menus Buttons In Playback mode the Up and Down button are used to speed up and slow down the playing of recorded video The Left and Right button will select the recorded video of 30 reverse at the IR receiver on the front panel If there is no response after you press any button on the remote follow the procedure below to troubleshoot Steps 1 Go to
52. 24 and 16 ch HDVR models 1 4 6 8 9 16 25 division window display modes supported and for other models 1 4 6 8 9 16 division window display modes are supported Dwell Time The duration between switching of channels when enabling auto switch in Live View Enable Audio Output Enable disable audio output for the selected video output When the VGA HDMI output interface is used as the main video output and the Audio Output for the VGA HDMI output interface is enabled the VGA HDMI audio and AUDIO OUT can be used for live view playback and two way audio When the VGA HDMI output is used as the main video output and the Audio Output for the VGA HDMI output interface is disabled the VGA HDMI output provides no audio and the AUDIO OUT is used for two way audio When the CVBS output is used as the main video output the VGA HDMI audio is provided for Aux video output in live view and the AUDIO OUT is used as the main video output for live view playback or two way audio Event Output Select the output to show event video The following interfaces are selectable VGA HDMI 48 User Manual of DS 7200 7300 8100 Series DVR Main CVBS and Spot Output 1 fore The Spot Output 1 is provided for DS 7300 SH and DS 8100 SH models Full Screen Monitoring Dwell Time The time in seconds to show alarm event screen 2 Setting Camera Order General Channel Zero Encoding VGA HDMI A1 Camera 02 Camera 03 Camera 04 Camera 05
53. 3 q v6 Address 1 fe80 240 30ff fedb d760 64 v6 Address 2 v6 Default Gateway MAC Address 00 40 30 db d7 60 MTU Bytes 1500 Preferred DNS Server 8 8 8 8 c Alternate DNS Server Figure 9 1 General Network Settings of DS 7204 7208 7216 NIC Type 10M 100M 1000M Self adaptive Enable DHCP Im IPv4 Address 172 6 23 74 IPv4 Subnet Mask Pa Para tra v4 Default Gateway UPS OPE mU v6 Address 1 fe80 240 30ff fef9 bfa8 64 6 Address 2 IPv6 Default Gatewa y 00 40 30 f9 bf a8 1500 Preferred DNS Server 8 8 8 8 Alternate DNS Serve Figure 9 2 General Network Settings of DS 7224 7232 and DS 7300 uada fore The DS 7204 7208 7216 models provide one 10M 100Mbps self adaptive network interface the DS 7224 7232 DS 7300 and DS 8104 8108 models provide one 1OM 100M 1000Mbps self adaptive network interface 3 In the General Settings interface You can configure the following settings NIC Type IPv4 Address IPv4 Gateway MTU and DNS Server 148 User Manual of DS 7200 7300 8100 Series DVR If the DHCP server is available you can click the checkbox of DHCP to automatically obtain an IP address and other network settings from that server fore e When the DHCP is failed the default IP address 192 168 1 64 will be used e The valid value range of MTU is 500 1500 4 After having configured the general settings click the Apply button to save the settings Steps for DS 8116 8124 8132 1
54. 7200 7300 8100 Series DVR the analog cameras You can also uncheck the checkbox to disable it nore This feature is available for DS 7204HWI SV DS 7224 7232HVI SH DS 7200HWI SH DS 7200HVI SV DS 7200HWI SL DS 7200HWI E1 2 C DS 7200HWI E1 E2 DS 7300HWI SH DS 7300HI SH DS 7300HWI E4 C DS 81000HWI E4 8 JC DS 8100HCI SH and DS 8100HWSI SH models only 5 Select the Main Stream and Substream for analog camera recording When the substream is selected you can record for a longer time with the same storage space 6 If you want to copy the current main stream settings to other analog camera s click Copy to enter the Copy Camera interface Select the analog camera s and click OK to finish the copy settings Copy to Analog Al BA2 EA3 HEA4 HBAS WAG vee LUNES Ce Pl CSERE Lu MA13 MHA14 HA15 FSL Figure 5 5 Copy Camera Settings 7 On the Record settings interface click Apply to save the settings NoTE You can click the Restore button to restore the current main stream settings to the default parameters 3 Set encoding parameters for sub stream 1 Click the Substream tab to enter the Substream settings interface Record Camera Analog 1 Stream Type Video amp Audio Resolution 176 120 QCIF Bitrate Type Variable Video Quality Medium Frame Rate 25 PAL 0 NTSC Max Bitrate Mode General Max Bitrate Kbps 128 Max Bitrate Range Reco 192 320 Kbps Figure 5 6 Encoding Parameters Sub stream 2 Con
55. 7304 DS 7308 provides 4 8 video input interfaces 23 User Manual of DS 7200 7300 8100 Series DVR Table 1 9 Description of Rear Panel BNC connector for video output BNC connector for spot video output 4 USB Interface Connects USB mouse or USB flash memory devices 6 VGA DBISconnectorfor VGA output Display local video output and menu 8 AUDIOOUT _ RCA connector for audio output S 9 LAN Interface RJ45 10M 100M 1000M Ethernet interface 0000 10 RS 485 Interface Connector for RS 485 devices Connect the D and D terminals to R and ull iudi R terminals of PTZ receiver respectively Ground needs to be connected when DVR starts up DS 7332 The rear panel of DS 7332 DVR is shown in Figure 1 10 O 7020909090909 o 04 04 0909090909090909595909590 09090909090909090909095 0969995959596 9596959595959 5 3 4 5 B f 8 9 10 1112 13 1415 Figure 1 10 Rear Panel of DS 7332 S NOTE DS 7324 provides 24 video input interfaces on the rear panel Table 1 10 Description of Rear Panel No BNC connector for video output BNC connector for spot video output 2 BNC connector for analog video input RCA connector for audio output This connector is synchronized with CVBS AUDIO OUT CVBS video output 3 RCA connector for audio output This connector is synchronized with VGA AUDIO OUT l VGA video output LINE IN RCA connector for two way audio input 5 AUDIO IN RCA connector for aud
56. 8 9 BE ENNMNENEMNENNNENENMNMI p p p p p b E Figure 5 28 Holiday Settings 3 Enable Edit Holiday schedule 1 Click A to enter the Edit interface Holiday1 By Date 02 07 2012 End Date 02 08 2012 Figure 5 29 Edit Holiday Settings 2 Check the checkbox after Enable 3 Select Mode from the dropdown list There are three different modes for the date format to configure holiday schedule 4 Setthe start and end date 90 User Manual of DS 7200 7300 8100 Series DVR 4 5 Click Apply to save settings 6 Click OK to exit the Edit interface Enter Record Schedule settings interface Menu Record Schedule Select Record 2 Check the checkbox after Enable Schedule 3 Click Edit 4 Select Holiday from the Schedule dropdown list Edit Holiday E 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Motion Motion Alarr Continuous Continuous Continuous Continuous Continuous Continuous 00 00 00 00 Continuous Cancel Figure 5 30 Edit Schedule Holiday 5 Select Motion or Continuous from the Type dropdown list 6 If you need all day recording check the All Day checkbox Otherwise leave it blank 7 Set start end time for holiday schedule NOTE Up to 8 periods can be configured for each day And the time periods can t be overlapped each other In the time table of the channel both
57. 9 2 5 Configuring NAT Purpose UPnP can permits the device seamlessly discover the presence of other network devices on the network and establish functional network services for data sharing communications etc If you want to use the UPnP function to enable the fast connection of the device to the WAN via a router you should configure the UPnP parameters of the device Before you start If you want to enable the UPnP function of the device you must enable the UPnP function of the router to which your device is connected When the network working mode of the device is set as multi address the Default Route of the device should be in the same network segment as that of the LAN IP address of the router Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the NAT tab to enter the NAT settings interface Enable UPnP a Mapping Type Manual Port Type Edit External External IP Address UPnP Status Z RTSP Port 554 0 0 0 0 Inactive E Server Port E 0 0 0 0 Inactive E HTTPS Port 0 0 0 0 Inactive Figure 9 21 UPnP Settings Interface 3 Check checkbox to enable UPnP M 4 Select the mapped type to Auto or Manual Task1 Auto 157 User Manual of DS 7200 7300 8100 Series DVR If you select Auto the Port Mapping items are read only and the external ports are set by the router automatically Steps 1 Click Apply to save the settings 2 Youcanclick Refresh to
58. 9 Toolbar of Playback by Event Table 6 1 Detailed Explanation of Playback by event Interface RN Mute Audio on LII Start Stop clipping E E Save clip s Pause EY Digital Zoom 30s backward Reverse Scaling up down Next event Video type bar time bar rar Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames About video type bar Ld represents normal recording manual or schedule B represents event recording B represents smart search recording 6 1 4 Playing Back by Tag Purpose Video tag allows you to record related information like people and location of a certain time point during playback You are also allowed to use video tag s to search for record files and position time point Before playing back by tag 1 Enter Playback interface 106 User Manual of DS 7200 7300 8100 Series DVR Normal H X irPcamera 01 MTwWTEFS mx U6 04 2U14 10 25 12 CE 1 Figure 6 10 Interface of Normal Playback Click button to add default tag Click button to add customized tag and input tag name g NOTE Max 64 tags can be added to a single video file 2 Tag management Click button to check edit and delete tag s Tag management Tag Name Time Del TAG 06 17 2014 17 06 25 Al 06 17 2014 17 06 27 TAG 06 17 2014 17 06 30 Total 3 P 1 1 Cancel Figure 6 11 Tag Management Interface Steps 1 Enter Playbac
59. Clear All to clear all zones Analog 1 Clear All C Clear Zone 1 Clear Zone 2 Clear Zone 3 Clear Zone 4 Figure 11 4 Set Privacy Mask Area 6 You can click the Copy button to copy the privacy mask settings of the current camera to other cameras Please refer to step 7 of Chapter 11 1 Configuring OSD Settings 7 Click the Apply button to save the settings hore You can also click the Restore to restore the current OSD settings to the default parameters 187 User Manual of DS 7200 7300 8100 Series DVR 11 3 Configuring Video Parameters Steps 1 Enter the Image Settings interface 2 3 ys Iria You can click the Restore button to restore the current image settings to default parameters Menu Camera Image Select the camera to set image parameters Set the period of a day for configuring independent image parameters so as to satisfy different light conditions e g daylight and night time Two periods can be configured When you have configured Time Segment 1 the Time Segment 2 is remained as the Other Time Camera Analog 1 Time Segment 1 00 00 12 00 Standard Figure 11 5 Image Settings Interface Select the mode from the drop down menu according to different light conditions Four modes are selectable Standard in general lighting conditions default Indoor the image is relatively smoother Dim Light the image is smoother than the other three modes O
60. Customizing Linear Scan Purpose Two limit points can be set for the view of the PTZ camera and then the PTZ camera can horizontally auto scan between the two predefined limits mE This function requires the support of the connected PTZ camera Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ Analog 1 Clear All Clear All Stop Clear All Left Limit Right Limit RS 485 Setti Figure 4 24 PTZ Settings Customize Linear Scan 2 Select the camera for PTZ setting from the drop down list 69 User Manual of DS 7200 7300 8100 Series DVR 3 Use the directional and zoom focus iris buttons on the PTZ control panel to steer the camera to the desired view and click the button Left Limit Right Limit to set the left right limit point Calling Linear Scan Purpose The PTZ camera will horizontally auto scan between the two predefined limit points Steps 1 Click the button MMES in the lower right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting toolbar during the live view process or click PTZ Control on the right click menu to open the PTZ control panel in live view mode 2 Select the PTZ camera from the drop down list for control 3 Click the icon I on the panel and then click the One touch tab to enter the One touch control interface 4 Click the Linear Scan button to start the linear scan 5 To stop the
61. Group If not set it to Group For detailed information please refer to Chapter 10 3 Managing HDD Group 3 Select General in the left bar Click A to enter editing interface 4 Configuring HDD group 1 Choose a group number for the HDD group 2 Click Apply and then in the pop up message box click Yes to save your settings 3 Click OK to back to the upper level menu Repeat the above steps3 4 to configure more HDD groups 5 Choose the Channels which you want to save the record files in the HDD group 1 Select Advanced on the left bar Mode Record on HDD Group 1 v Analog E41 H2 OMAR At GAS BAG GA v IP Camera v M B v E Enable HDD Sleeping Figure 5 35 HDD Advanced 2 Choose Group number in the dropdown list of Record on HDD Group 3 Check the channels you want to save in this group 4 Click Apply to save settings 94 User Manual of DS 7200 7300 8100 Series DVR E NOTE After having configured the HDD groups you can configure the Recording settings following the procedure provided in Chapter 5 2 5 6 95 User Manual of DS 7200 7300 8100 Series DVR 5 9 Files Protection Purpose You can lock the recorded files or set the HDD property to Read only to protect the record files from being overwritten Protect file by locking the record files Steps 1 Enter Playback setting interface Menu Export E Analog E A1 MA2 EX Iv A4 MA5 MAG MiP Camera MDi WDd2 01 01 1970 00 00 23 12
62. Local 927GB Figure 10 17 View HDD Status 1 cn Nore If the status of HDD is Normal or Sleeping it works normally If the status 1s Uninitialized or Abnormal please initialize the HDD before use And if the HDD initialization is failed please replace it with a new one Checking HDD Status in HDD Information Interface Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the HDD tab to view the status of HDD displayed on the list Device Info Camera Record Network Normal 931 51GB 931 51GB 927GB Figure 10 18 View HDD Status 2 181 User Manual of DS 7200 7300 8100 Series DVR 10 6 Checking S M A R T Information Purpose The S M A R T Self Monitoring Analysis and Reporting Technology is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures Steps 1 Enter the S M A R T Settings interface Menu gt Maintenance gt HDD Detect gt S M A R T Settings 2 Select the HDD to view its S M A R T information list NOTE If you want to use the HDD even when the S M A R T checking is failed you can check the checkbox before the Continue to use this disk when self evaluation is failed item 3 Three self tests of S M A R T are provided including Short Test Expanded Test and Conveyance Test You can select a self test type and click to start self test Bad Sector Detection E Continue to use th
63. Menu gt Configuration gt General gt More Settings by operating the mouse 2 Check and remember the device No The default No is 255 This device No is valid for all the IR remote controls 3 Press the DEV button on the remote control 4 Enter the device No from step 2 5 Press the ENTER button on the remote If the remote control is operating properly but there is still no response from the remote please check the following 1 Batteries are installed correctly and the polarities of the batteries are not reversed 2 Batteries are fresh and not out of charge 3 IR receiver is not obstructed If the remote still can t function properly please change a remote and try again or contact the device provider 20 User Manual of DS 7200 7300 8100 Series DVR 1 3 USB Mouse Operation A regular 3 button Left Right Scroll wheel USB mouse can also be used with this device To use a USB mouse 1 Plug USB mouse into one of the USB interfaces on the front panel of the device 2 The mouse should automatically be detected If in a rare case that the mouse is not detected the possible reason may be that the two devices are not compatible please refer to the recommended device list from your provider The operation of the mouse Table 1 5 Description of the Mouse Control single Click Live view Select channel and show the quick set menu Menu Select and enter Double Click Live view Switch single screen and multi screen
64. TZ Control mode the button adjusts the iris of the camera In Playback mode it can be used to generate video clips for backup F2 AUX The F2 AUX button is used to cycle through tab pages OM In PTZ Control mode it can be used to zoom out the PTZ camera Switch between single screen and multi screen mode PREV FOCUS In PTZ Control mode it is used to adjust the focus in conjunction with the A FOCUS button Enter the PTZ Control mode DIRECTION The DIRECTION buttons are used to navigate between different fields and items 17 User Manual of DS 7200 7300 8100 Series DVR Function Description JOG SHUTTLE Control in menus In Playback mode the Up and Down button is used to speed up and slow down recorded video In All day Playback mode the Left Right button can be used to select the recorded video of next previous day in Playback by Normal Video Search the Left Right button can be used to select the next previous recorded file In Live View mode the directional buttons can be used to cycle through channels In PTZ control mode it can control the movement of the PTZ camera Confirm selection in any of the menu modes It can also be used to tick checkbox fields In Playback mode it can be used to play or pause the video In Single frame Playback mode pressing the ENTER button will advance the video by a single frame In Auto switch mode it can be used to stop start auto switch Move the active selection in a menu T
65. The Administrator has the permission to add and delete user and configure user parameters 13 5 1 Adding a User Steps 1l Enter the User Management interface Menu Configuration User 00 00 00 00 00 00 00 00 00 00 00 00 Figure 13 5 User Management Interface 2 Click the Add button to enter the Add User interface Add User test02 ttrt Guest 00 00 00 00 00 00 Figure 13 6 Add User Menu 3 Enter the information for new user including User Name Password Level and User s MAC Address Level Set the user level to Operator or Guest Different user levels have different operating permission 204 User Manual of DS 7200 7300 8100 Series DVR Operator The Operator user level has permission of Local Log Search in Local Configuration Remote Log Search and Two way Audio in Remote Configuration and all operating permission in Camera Configuration Guest The Guest user has permission of Local Log Search in Local Configuration Remote Log Search in Remote Configuration and only has the local remote playback in the Camera Configuration User s MAC Address The MAC address of the remote PC which logs onto the device If it is configured and enabled it only allows the remote user with this MAC address to access the device Click the OK button to save the settings and go back to the User Management interface The added new user will be displayed on the list as shown in Figure 13 6 admin Admin 00 00 0
66. Type Enable DHCP IPv4 Address IPv4 Subnet Mask IPv4 Default Gateway IPv6 Address IPv6 Address 2 IPv6 Default Gateway MAC Address MTU Bytes Preferred DNS Server PPPOE DDNS NTP Email SNMP NAT More Settings 10M 100M 1 000M Self adaptive Wu 172 6 23 74 200929029520 lite Oem coe fe80 240 30ff fef9 bfa8 64 00 40 30 f9 bf a8 1500 192 0 0 200 Alternate DNS Server Figure 9 35 Network Settings Interface 3 Click the Apply button to save the settings 4 Select the Email tab to enter the Email Settings interface Receiver 1 Figure 9 36 Email Settings Interface 164 User Manual of DS 7200 7300 8100 Series DVR 3 6 Lid Email test succeeded Configure the following Email settings Enable Server Authentication optional Check the checkbox to enable the server authentication feature User Name The user account of sender s Email for SMTP server authentication Password The password of sender s Email for SMTP server authentication SMTP Server The SMTP Server IP address or host name e g smtp 263xmail com SMTP Port The SMTP port The default TCP IP port used for SMTP is 25 Enable SSL optional Click the checkbox to enable SSL if required by the SMTP server Sender The name of sender Sender s Address The Email address of sender Select Receivers Select the receiver Up to 3 receivers can be configured Receiver The name of user to be notified Receiver s Addr
67. a a 182 10 7 IDetectin Bac Seco xe iof taut eua 183 10 8 Configuring HDD Error Alarms e eceeseeeeeeeeeeee nennen 184 Chapter IT Camera Settee ss scsssssssissassusssnscsussanssaussansccuscanacauasansesuscanasauasanseaussawavauasavacauseanss 185 11 1 Concurring OSD Sein gs activin anise E PA RU eiY 186 11 2 Contre arin amp Pry acy MaSK enepar teo NaN No De RD PIpLE NE Ru eo RE Mold edu e 187 11 3 Configuring Video Parameters oe ooo tie ea 188 11 4 Configuring Video Quality Diagnostics cccccccccccceecceeeeeeeaeeeeseesseseeeeeeees 189 Chapter 12 Device Management and Maintenance eee e eee e e e eee eee e ette eese eee 191 12 1 View ine Systema InforrtdtlODb soie Eo tus fe orb edd eaa 192 12 2 Searching amp Exporting Log Files eeeeeeesssssesseeeeeeeeeeee nnn 192 12 3 Importing Exporting Configuration Files ccccccccccccccceceeesesssesseeeeeeeeeees 194 12 4 Uperadine NR DH 196 12 4 1 Upgrading by Local Backup Device eeeeeeeeem 196 1242 DU peradiie Dy PIP iode ie eic hi ee E Redde R 196 12 5 Ixestorme Derli Se Ulli Sc or eet edad dec ae aper E e erede diu des 198 Chapter 15 OU Crs iere cie ero s a Yr EDT s rie s vU OU NITE 199 13 1 Configuring General Settings eeeeesssssssssssssssseseseeee enne nennen 200 13 2 Confis rne R5 252 Serial POTE o tr ior err ar e AERE 201 13 3 Conlieurime DS T Seltig Scu e
68. al 2 Click the More Settings tab to enter the More Settings interface General DST Settings Device Name Embedded Net DVR Device No 255 CVBS Output Brightness Auto Logout 30 Minutes Menu Output Mode Auto Main CYBS Scaling Figure 13 4 More Settings Interface 3 Configure the following settings e Device Name Edit the name of device e Device No Edit the serial number of device The Device No can be set in the range of 1 255 and the default No is 255 e CVBS Output Brightness Adjust the video output brightness e Operation Timeout Set timeout time for menu inactivity E g when the timeout time is set to 5 Minutes the system will exit from the current operation menu to live view screen after 5 minutes of menu inactivity e Menu Output Mode Select the menu output mode to Auto HDMI VGA or Main CVBS fore e When you select Auto the device can automatically detect the HDMI VGA output as the main output and the CVBS output as the auxiliary output when it starts up e After you have changed the output mode you should restart the device to activate the new settings e Main CVBS Scaling Enable disable video output scaling for main CVBS video output 4 Click the Apply button to save the settings 203 User Manual of DS 7200 7300 8100 Series DVR 13 5 Managing User Accounts Purpose There is a default account in the device Administrator The Administrator user name is admin and the password is 12345
69. amera interface as shown in Figure 11 2 Copy to Analog 11 LZ VEM LX HA4 HAS MAG HA7 Et LU EWWIUEM LAXE LA MAi3 HA14 HA15 HA16 Figure 11 2 Copy Settings to Other Cameras 2 Select the camera s to be configured with the same OSD settings You can also click the checkbox of Analog to select all cameras 3 Click the OK button to finish the Copy settings and back to the OSD Configuration interface 8 Click the Apply button to apply the settings mE You can also click the Restore to restore the current OSD settings to the default parameters 186 User Manual of DS 7200 7300 8100 Series DVR 11 2 Configuring Privacy Mask Purpose You are allowed to configure the four sided privacy mask zones that cannot be viewed by the operator Steps 1 Enter the Privacy Mask Settings interface Menu Camera Privacy Mask 2 Select the camera to set privacy mask 3 Click the checkbox of Enable Privacy Mask to enable this feature Analog 1 Clear All C Clear Zone 1 Clear Zone 2 Clear Zone 3 Clear Zone 4 Figure 11 3 Privacy Mask Settings Interface 4 Use the mouse to draw a zone on the window The zones will be marked with different frame colors Iris Up to 4 privacy mask zones can be configured and the size of each area can be adjusted 5 The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear Zone 4 icons on the right side of the window or click
70. andards do not match Record Exception No space for saving recorded file c m Input Output Video Standard Mismatch and Video Signal Exception are not supported by IP cameras of HDVR series Steps 1 Enter Exceptions interface and handle various exceptions Menu gt Configuration gt Exceptions 2 Check the checkbox of Enable Event Hint to display the Event Exception icon when the exceptional event occurs And click the icon to select the detailed event hint for display mE Click the icon appears in the live view interface and you can view the detailed information of the exceptional event Click the button Set and then you can select the detailed event hint for display Event Hint Settings v FA EAHDD Error E Network Disconnected EIP Conflicted Elillegal Login Edinput Output Video Standard Mismatch iv AIT TO Signal Loss MAlarm Input Triggered E Video Tamper Detected EaMotion Detection Record Exception Sir Fraai anda al Figure 8 22 Detailed Event Hint Settings 3 Set the alarm linkage actions For details see Chapter 8 7 4 Click Apply to save the settings 142 User Manual of DS 7200 7300 8100 Series DVR Enable Event Hint Event Hint Settings 3 HDD Full E a ES Figure 8 23 Exception Settings Interface 143 User Manual of DS 7200 7300 8100 Series DVR 8 7 Setting Alarm Response Actions Purpose The alarm response actions will be activated when an exception occu
71. ber ied re TTS Call Preset Pattern 1 amp Hoo Patrol 1 Add KeyPoint ojo O Gi Figure 4 6 PTZ Add Key Point 4 Configure key point parameters such as the key point No duration of staying for one key point and speed of patrol The key point is corresponding to the preset The Key Point No determines the order at which the PTZ will follow while cycling through the patrol The Duration refers to the time span to stay at the corresponding key point The Speed defines the speed at which the PTZ will move from one key point to the next KeyPoint KeyPoint 1 Cancel Figure 4 7 Key point Configuration 5 Click OK to save the key point to the patrol 57 User Manual of DS 7200 7300 8100 Series DVR Repeat the above steps to add more key points You can also delete all the key points by clicking the trash icon Dave Presets Call Preset Pattern 1 AEN OG oO Patrol 1 Preset 1 Preset Preset 3 Figure 4 8 KeyPoints Deletion Calling Patrols Purpose Calling a patrol makes the PTZ to move according the predefined patrol path Call patrol in the PTZ setting interface Steps 1 In the PTZ setting interface Menu gt Camera gt PTZ gt More Settings 2 Select the patrol number and then click to call the patrol 3 Click El to stop it Dave Presets Call Preset Pattern 1 gt Patrol 1 Preset 1 Preset Preset 3 Figure 4 9 Calling Patrol
72. cal 3 lllLocal 4 lllLocal 5 lllLocal 6 lllLocal 7 lllLocal 8 W 172 6 23 3 8000 lt 1 Cancel Figure 5 24 Copy Alarm Input 3 Enter Record Schedule settings interface Menu gt Record gt Schedule gt Record Schedule For detailed information about record schedule settings refer to step 2 in Chapter 5 2 Configuring Record Schedule mE You need to select the Type as Alarm in record schedule settings 87 User Manual of DS 7200 7300 8100 Series DVR Analog 1 a 8 10 16 18 20 22 24 zs pupa epu p pp SaaS ea Figure 5 25 Record Schedule The VCA recording type is supported by the Smart DVR HDVR series only 88 a Oo OT A O Na Edit Continuous Event Motion Alarm MIA LIT VCA None User Manual of DS 7200 7300 8100 Series DVR 5 5 Configuring Manual Record Purpose Follow the steps to set parameters for the manual record When using manual record you need to manually cancel the record The manual recording is prior to the scheduled recording Steps 1 Enter the Manual settings interface Menu Manual Analog A1 IP Camera D1 Recording by schedule Recording by manual operation Continuous tf Motion Detection d Figure 5 26 Manual Record ge NOTE The IP Camera is supported by HDVR series only 2 Enable recording for camera s Click the status button beside each camera number to change zi to EI or you can enable recording for all ca
73. case of one NIC card failure the device will automatically enable the other standby NIC card so as to ensure the normal running of the whole system Net Fault tolerance a 172 6 21 110 255 255 255 0 172 6 5 fe80 240 3dff fe 7e 9262 64 00 40 3d 7e 92 62 1500 Figure 9 6 Net Fault tolerance Working Mode 150 User Manual of DS 7200 7300 8100 Series DVR 9 2 Configuring Advanced Settings 9 2 1 Configuring Extranet Access You can choose the access to the DVR by EZVIZ Cloud P2P or by DDNS through the settings on the Extranet Access menu Cu By default the EZVIZ Cloud P2P is enabled Configuring EZVIZ Cloud P2P Purpose EZVIZ Cloud P2P provides the mobile phone application and as well the service platform page to access and manage your connected DVR which enables you to get a convenient remotely access to the surveillance system Steps 1 Enter the Network Settings interface Menu Configuration Network Select the Extranet Access tab to enter the EZVIZ Cloud P2P Settings interface Check the Enable EZVIZ Cloud P2P checkbox to activate this feature If required check the Enable Stream Encryption checkbox to encrypt the video stream um ode D qu Enter the verification code of the device fore The verification code consists of 6 capital letters and is located at the bottom of the DVR The device at the version 3 0 1 or above has its verification code automatically available in th
74. cing by dragging mouse HDD Management 1 SATA hard disk can be connected to DS 7200HVI SH DS 7200HVI SV DS 7204HFI SH DS 7204HWI SV and DS 7204HWI SH DS 7200HWI SL DS 7200HWI E1 DS 7204HWI E1 C models 2 SATA hard disks to DS 7208 7216HFI SH DS 7208 7216HWI SH DS 7208 7216HWI E2 C DS 7208 7216 7224HWI E2 DS 7224 7232HVI SH and DS 7224 7232HWI SH models up to 4 SATA hard disks to DS 7300 and DS 8104HWI E4 C and up to 8 SATA hard disks to DS 8100 SH DS 8108HWI ES C and DS 8116HWI E8 C with a maximum of 4TB storage capacity for each disk 8 network disks 8 NAS disks or 7 NAS disks 1 IP SAN disk can be connected User Manual of DS 7200 7300 8100 Series DVR HDD group management Support HDD standby function HDD property redundancy read only read write R W HDD quota management different capacity can be assigned to different channel Recording and Playback Holiday recording schedule configuration Normal and event video encoding parameters e Multiple recording types manual normal motion alarm motion alarm motion amp alarm and VCA 7 The alarm motion alarm and motion amp alarm recording types are provided for DS 7224 7232 DS 7300 and DS 8100 HDVR models only And the VCA recording type is supported by the smart DVR HDVR models only Recording by main stream or sub stream is configurable X 5recording time periods with separated recording types X Pre record an
75. ck Apply button to save the settings 4 2 1 Setting PTZ Presets Patrols amp Patterns Before you start Please make sure that the presets patrols and patterns should be supported by PTZ protocols 54 User Manual of DS 7200 7300 8100 Series DVR Customizing Presets Purpose Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings Analog 1 Le Save Preset aiee age eae a ad d 8 9 10 11 12 2 Es is t obey os eu s a d ees Call Preset Pattern 1 i110 0 Patrol 4 Figure 4 2 PTZ More Settings 2 Use the directional button to wheel the camera to the location where you want to set preset 3 Click the round icon before Save Preset 4 Click the preset number to save the preset Repeat the steps2 4 to save more presets If the number of the presets you want to save is more than 17 you can click and choose the available numbers Preset Cancel Figure 4 3 More Presets Calling Presets Purpose This feature enables the camera to point to a specified position such as a window when an event takes place Call preset in the PTZ setting interface Steps 55 User Manual of DS 7200 7300 8100 Series DVR 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Check the round icon before Call Preset Analog 1 Save Prese
76. compatibility from vendor 128 User Manual of DS 7200 7300 8100 Series DVR Chapter 8 Alarm Settings 129 User Manual of DS 7200 7300 8100 Series DVR 8 1 Setting Motion Detection Steps 1 Enter Motion Detection interface and choose a camera you want to set motion detection Menu Camera Motion Full Screen Clear Figure 8 1 Motion Detection Setup Interface 2 Set motion detection area and sensitivity 1 Check the checkbox of Enable Motion Detection to enable motion detection use the mouse to draw detection area s and drag the sensitivity bar to set sensitivity Please refer to Chapter 5 3 Configuring Motion Detection Record g By default the motion detection is enabled and configured in full screen 2 Click the EI of Settings to set alarm response actions Camera Analog 1 Enable Motion Detection LE b e dou J Mn 1 Figure 8 2 Set Detection Area and Sensitivity 3 Click Trigger Channel tab and select one or more channels which will start to record or become full screen monitoring when motion alarm is triggered 130 User Manual of DS 7200 7300 8100 Series DVR Seltings Arming Schedule Linkage Action ll Analog MA1 MA2 MAS MA4t BAS BAG MAr FL EIP Camera I Figure 8 3 Set Trigger Camera of Motion Detection 4 Set up arming schedule of the channel 1 Select Arming Schedule tab to set the channel s arming schedule 2 Choose one day of a week and up to eight time
77. d post record for motion detection for recording and pre record time for schedule and manual recording X Searching record files by event Customization of tags searching and playing back by tags Locking and unlocking record files Local redundant recording X Searching and playing back record files by channel number recording type start time end time etc Smart search for the selected area in the video Smart playback to go through less effective information X Zooming in when playback Playing reversely Support pause fast forward slow forward skip forward and skip backward when playback locating by dragging the mouse e 4 8 16 ch synchronous playback Backup Export video data by USB SATA or eSATA storage device ore The eSATA is supported by DS 7300 and DS 8100 models only X Export video clips when playback Management and maintenance of backup devices Alarm and Exception Configurable arming time of alarm input output for DS 7224 7232 DS 7300 and DS 8100 models Alarm for video loss motion detection tampering abnormal signal video input output standard mismatch illegal login network disconnected IP confliction abnormal record HDD error and HDD full etc Alarm event triggers full screen monitoring audio alarm notifying surveillance center and sending email Automatic restore when system is abnormal VCA detection alarm line crossing
78. de is Quota please set the maximum record capacity For detailed information see Chapter 10 4 Configuring Quota Mode 3 If the HDD mode is Group you should set the HDD group For detailed information see Chapter 5 6 Configuring HDD Group for Record Mode Record on HDD Group iv Analog v FVE Fy F pr NEM PEE v F FT P MIP Camera v PL Dy Enable HDD Sleeping Figure 5 2 HDD Advanced Steps 1 Enter the Record settings interface to configure the encoding parameters Menu gt Record gt Parameters 74 User Manual of DS 7200 7300 8100 Series DVR Record Substream Analog 1 Main Stream Continuous Video amp Audio 704 480 4CIF Variable Medium 25 PAL 30 NTSC General 1792 1152 1920 Kbps 5s 5s 0 jai Main Stream Restore Main Stream Event Video amp Audio 704 480 4CIF Variable Medium 25 PAL 30 NTSC General 1792 1152 1920 Kbps Figure 5 3 1 Encoding Parameters Main Stream Analog Camera Record Substream IP Camera 1 Main Stream Continuous Video amp Audio 1920 1080 1080P Variable Medium 25 PAL 30 NTSC General 4096 3840 6400 Kbps 5s 5s 0 pet Main Stream Event 25 PAL 30 NTSC General 2048 3840 6400 Kbps Figure 5 4 2 Encoding Parameters Main Stream IP Camera 2 Set encoding parameters for main stream 1 Select Record to enter the main stream settings interface 2 Select the camera for configuration 3 Configure t
79. details of Email configuration Trigger Alarm Output This feature is available for DS 7224 7232 DS 7300 and DS 8100 models only Trigger an alarm output when an alarm is triggered Steps 1 Enter Alarm Output interface Menu gt Configuration gt Alarm gt Alarm Output Select an alarm output and set alarm name and dwell time 144 User Manual of DS 7200 7300 8100 Series DVR NOTE If Manually Clear is selected in the dropdown list of Dwell Time you can clear it only by going to Menu gt Manual gt Alarm and clicking Clear All Alarm Status Alarm Input Alarm Output N Local 1 Alarm Name Dwell Time os settings dl Figure 8 24 Alarm Output Settings Interface 2 Set arming schedule of the alarm output Click to set the arming schedule of alarm output Choose one day of a week and up to 8 time periods can be set within each day woe fore Time periods shall not be repeated or overlapped Settings Mon lt 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Figure 8 25 Set Arming Schedule of Alarm Output 3 Repeat the above steps to set up arming schedule of other days of a week You can also click Copy to copy an arming schedule to other days Click OK to complete the settings of the alarm output 4 You can also click Copy in Alarm Output interface to copy the above settings to another channel Copy Alarm Output to WAlarm Output N
80. detection and intrusion detection is supported by the smart DVR HDVR series User Manual of DS 7200 7300 8100 Series DVR Support alarm push notification live video or playback on the linked mobile phones when alarm event occurs M ai NOTE The mobile phone must be installed with the 1VMS 4500 client software and the alarm push function 1s enabled Other Local Functions Operable by mouse IR remote control or front panel for DS 7300 and DS 8100 Three level user management admin user is allowed to create many operating accounts and define their operating permission which includes the limit to access any channel Operation exceptions and log recording and searching Import and export of device configuration information Network Functions self adaptive 10M 100M network interface for DS 7204 7208 7216 and 1 self adaptive 10M 100M 1000M network interface for DS 7224 7232 and DS 7300 and 2 self adaptive 10M 100M 1000M network interfaces for DS 8100 models IPv6 is supported TCP IP protocol PPPoE DHCP DNS DDNS RTSP NTP SADP SMTP SNMP NES and iSCSI are supported Extranet access by HiDDNS Support access by EZ VIZ Cloud P2P TCP UDP and RTP for unicast Auto Manual port mapping and automatically discovered by NAT DS 7200HWI E1 2 C DS 7300HWI E4 C and DS 81OOHWI E4 8 C series support HIKVISION C and PELCO C Coaxitron protocols Remote search playback download locking and unlocking of the rec
81. displayed When it fails to detect the backup device please check whether it 1s compatible with the device You can format the backup device if the format is incorrect Traffic Network Stat Network Delay Packet Loss Test Select NIC LAN1 Destination Address Network Packet Export Device Name USB 1 1 Refresh LAN1 172 6 23 186 Export Figure 9 42 Export Network Packet 4 Click the Export button to start exporting 5 After the exporting is complete click OK to finish the packet export Packet exporting Attention Packet export succeeded Figure 9 43 Packet Export Attention fore Up to 1M data can be exported each time 9 4 3 Checking Network Status Purpose You can also check the network status and quick set the network parameters in this interface Steps Click Status on the right bottom of the page 168 User Manual of DS 7200 7300 8100 Series DVR Traffic Network Stat Network Delay Packet Loss Test LAN1 Network Packet Export TY Refresh LAN1 172 6 23 74 2 277Kbps Export Status Network Figure 9 44 Checking Network Status If the network is normal the corresponding message box pops out If the message box pops out with other information instead of this one you can click Network button to show the quick setting interface of the network parameters Network NIC Type 10M 100M Self adaptive Enable DHCP E 172 6 24 64 255 255 255 0 UP A Cancel Figure 9 45 Networ
82. drop down list 3 Select the pattern number from the drop down list Click the Start button under the Pattern item and click the eight pan tilt directional buttons and the zoom iris focus buttons under the image to move the PTZ camera Click the Stop button and the movement of PTZ is recorded as the pattern You can click the Clear All button under the Pattern item to clear all the presets Calling Patterns Purpose The PTZ camera will move according to the predefined pattern path when you call a pattern Steps 1 Click the button MMES in the lower right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting toolbar during the live view process or click PTZ Control on the right click menu to open the PTZ control panel in live view mode Select the PTZ camera from the drop down list for control Click the icon gt on the panel and then click the General tab to enter the general PTZ control interface Select the patrol from the corresponding drop down list and then click the Call Pattern button to start the pattern To stop the pattern you can click the button Stop Pattern on the panel 68 User Manual of DS 7200 7300 8100 Series DVR PTZ ra Analog 1 Configuration ES O y 4 One touch Call Preset Call Patrol Stop Pa 1 Call Patt Stop Pa 1 Figure 4 23 Control Panel Call Pattern 4 2 2 Configuring Linear Scan
83. e filed by default for device of older version you need to input any 6 capital letters in the text filed Enable EZVIZ Cloud P2P Enable Stream Encryption E Verification Code ABCDEF Enable DDNS m DDNS Type HIDDNS Server Address Device Domain Name User Name Figure 9 7 EZVIZ Cloud P2P Settings Interface 6 Click the Apply button to save and exit the interface After configuration you can access and manage the DVR by your mobile phone on which the EZ VIZ Cloud P2P application is installed or by the ezviz website www ezviz7 com E NOTE 151 User Manual of DS 7200 7300 8100 Series DVR For more operation instructions please refer to the help file on the EZVIZ Cloud P2P website Configuring DDNS Purpose If your device is set to use PPPoE as its default network connection you may set Dynamic DNS DDNS to be used for network access Prior registration with your ISP is required before configuring the system to use DDNS Steps 1 Enter the Network Settings interface Menu Configuration Network 2 Select the Extranet Access tab to enter the DDNS Settings interface Figure 9 8 DDNS Settings Interface Check the Enable DDNS checkbox to activate this feature Select DDNS Type Five different DDNS types are selectable IPServer DynDNS PeanutHull NO IP and HiDDNS PServer Enter Server Address for IPServer mE The Server Address should be the IP address of the PC that runs IPServer IPServer
84. e Exporting interface until all record files are exported to the USB flash drive 5 Check backup result Choose the record file in Export interface and click button to check it fore The Player player exe will be exported automatically during record file export Device Name Refresh Name Size Type Edit Date Delete Play Bi ch01_20130722085 2 626KB File 07 22 2013 10 11 20 m C Bi player exe 786KB File 07 22 2013 10 11 19 TT Free Space 7 660MB New Folder Format Cancel Figure 7 3 Checkup of Quick Export Result Using USB1 1 7 1 2 Backing up by Normal Video Search Purpose The record files can be backup to various devices such as USB devices USB flash drives USB HDDs USB 118 User Manual of DS 7200 7300 8100 Series DVR writer SATA writer or eSATA HDD Tus The eSATA writer is supported by DS 7300 and DS 8100 models only Backup using USB flash drives USB HDDs USB writer SATA writer or eSATA HDD Steps 1 Enter Export interface Menu gt Export gt Normal Analog iv A1 A2 A3 A4 A5 A6 A7 A8 WIP Camera BDI 9 01 01 2013 00 00 23 12 23 2013 17 44 30 All All 12 23 2013 i 00 00 00 12 24 2013 23 59 59 Quick Export Search Figure 7 4 Normal Video Search for Backup 2 Setsearch conditions and click Search button to enter the search result interface 3 Select record files you want to back up Click button to play the record file if you want to check it Check the chec
85. e OE RE Ip OMIM IM aA 202 13 4 Conmeurine MOLC SeBLITIg Soo ios r oua CL Ea d Clopdba PH SO LN P DEDE VEA Ra e 203 13 5 Mama sili User AC COUNES 35 55 29 i RIDE HISEAUR SEEN Etude Ote EH PIE LU Pp a CE delis d uid 204 1559 ESO de cs Beemer ane Seen tuis nem nara turtetan tot To ursa tit Leurs nen Moreen ons ane 204 15 5 2 Derim TU i ec cerdo ta on om ar QUEE deste d Ma Goa dou IO e See 206 PSone dW set aeo vio Et cte LR UNE te E dr ces 207 13 5 4 Changing Password of Admin a a a 208 Chapter I4 ADDODUOIIX e vuv eucokoe vade sua E cea pev dco eve Cea eve dco sva v e quaeve eco save ENa EO 210 Listor Compatible Hikvision IP C meras iiie ie peor Res he E c speeds six qp ot itiss 211 11 User Manual of DS 7200 7300 8100 Series DVR GIOSSAt V iio eap rte oi RE pe Od rfr T OUO SDOGLITIG ases coated e ean sauces a a e ad t a rat 12 User Manual of DS 7200 7300 8100 Series DVR Chapter 1 Introduction User Manual of DS 7200 7300 8100 Series DVR 1 1 Front Panel DS 7200 The front panel of DS 7200 series DVR is shown in Figure 1 1 HIKVISION Figure 1 1 Front Panel of DS 7200 Table 1 1 Description of Control Panel Buttons STATUS indicator lights in red when HDD is reading writing Tx Rx indictor blinks green when network connection is functioning properly Connects USB mouse or USB flash memory devices Receiver for IR remote DS 7300 The front panel of DS 7300 is shown below Nek a uk us wt 6 W
86. e a hei a lov au bod dea td d 161 2 2 9 X ontteurine server amd EPIEDP POtbSa oe eie e SERM IRR ER IMS pA IU 162 10 User Manual of DS 7200 7300 8100 Series DVR 29 2 10 Contieurins HE TPS Sctunes eredi ea e res 162 22 E Conmeouitc ETSI o oi ode etra esed escas 164 9 3 Checking Network TEall6 id om i idreito toi Ebor o coi abr eo PEE tide I Li d 166 9 4 Network IDC LECH OM e eoo EREHRR RR ENA 167 9 4 1 Testing Network Delay and Packet Loss eeeeeeeeese 167 JA TEDNE Network PaOKeEusni todos terio een ER Etro NO Ie HIR HIERO Ion E NIE Pelri ta d 167 0 4 5 Checking Network Stats 6o i tope en e ho taser veo eh bt eot fo bote ne toos 168 29 4 Neck ing NetWork StaUstlGs cio eive or RID EN do eee ee era 169 Chapter 10 HDD Management e eee eee ee eee enun unen e rrr oorr onere eene ee oou e e o Pear epe e etae eere eaa oue 171 10 1 Ingtializine ol BD to OE IRE e Ns 172 10 2 Managing Network EDD iieri I teca dora hera leu tadoe sa dee td 174 10 3 Manasine HDD Group e ud ori aUe CHRON ERe a pe REOR HR REB EN 177 10 5 1 Setting HDD Groups icio i qu tes USE coc hac d Cla o as DOE PE Oc aede ete 177 10 5 Serine MDD Property a enieius desti tein a ee Ee on Cua tup ro sen dede 178 10 4 Conftie rme Quota Mode 2E Mr CHER E read oo Fl eR Me E Dod de todo aident 180 10 5 Checkins ADD Status s o eulos en parca Sev ada diu sae eden E erede dide 181 10 6 Checking S ML ACR T Information 4 dier e
87. e certificate request Day range 1 5000 2 Download the certificate request and submit it to the trusted certificate authority for signature 3 After receiving the signed valid certificate import the certificate to the device 3 The certificate information will be displayed after you successfully created and installed the certificate Installed Certificate Installed Certificate Property Subject C CN H P 172 6 23 110 Issuer C CN H IP 172 6 23 110 Validity 2013 06 28 10 42 40 2013 06 30 10 42 40 Figure 9 34 Installed Certificate Property 4 Check the checkbox to enable the HTTPS function Cu The HTTPS Port should be set to the range of 1 65535 163 Delete User Manual of DS 7200 7300 8100 Series DVR 9 2 11 Configuring Email Purpose The system can be configured to send an Email notification to all designated users if an alarm event is detected a motion detection event 1s detected etc Before configuring the Email settings the device must be connected to a local area network LAN that maintains an SMTP mail server The network must also be connected to either an intranet or the Internet depending on the location of the e mail accounts to which you want to send notification Steps 1 Enterthe Network Settings interface Menu Configuration Network 2 Set the IPv4 Address IPv4 Subnet Mask IPv4 Gateway and the Preferred DNS Server in the Network Settings menu General NIC
88. e content is subject to Smart Coaxitron HDVR change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual User Manual of DS 7200 7300 8100 Series DVR Preventive and Cautionary Tips Before connecting and operating your device please be advised of the following tips Ensure unit 1s installed in a well ventilated dust free environment Unit is designed for indoor use only Keep all liquids away from the device Ensure environmental conditions meet factory specifications Ensure unit is properly secured to a rack or shelf Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit Use the device in conjunction with an UPS if possible Power down the unit before connecting and disconnecting accessories and peripherals A factory recommended HDD should be used for this device Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the manufacturer User Manual of DS 7200 7300 8100 Series DVR Product Key Features General o Connectable to the network cameras and network domes this feature is supported by HDVR series Connectable to the Coaxitron camera dome for DS 7200HWI E1 2 C DS 7300HWI E4 C and DS 8100HWI
89. e exists packet loss during the transmission b The frame rate is not the real time frame rate Steps 1 Verify the network between HDVR and IPC is connected 1 When image is stuck connect the RS 232 ports on PC and the rear panel of HDVR with the RS 232 cable 2 Open the Super Terminal and execute the command of ping 792 168 0 0 1 1472 f the IP address may change according to the real condition and check if there exists packet loss E Simultaneously press the Ctrl and C to exit the ping command 2 Verify the frame rate is real time frame rate Select Menu gt Record gt Parameters gt Record and set the Frame Rate to full frame 216 User Manual of DS 7200 7300 8100 Series DVR Verify the hardware can afford the playback Reduce the channel number of playback Select Menu gt Record gt Encoding gt Record and set the resolution and bitrate to a lower level Reduce the number of local playback channel Select Menu gt Playback and uncheck the checkbox of unnecessary channels Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from our company to do the further process No record file found in the device local HDD and the prompt No record file found pops up when you search the record files Possible Reasons a The time setting of system is incorrect b The search condition is incorrect c The
90. e new firmware 12 4 2 Upgrading by FTP Before you start Ensure the network connection of the PC running FTP server and the device is valid and correct Run the FTP server on the PC and copy the firmware into the corresponding directory of your PC cuc Refer to the user manual of the FTP server to set the FTP server on your PC and put the firmware file into the directory as required Steps 1 Enter the Upgrade interface Menu Maintenance Upgrade 2 Click the FTP tab to enter the local upgrade interface 196 User Manual of DS 7200 7300 8100 Series DVR Local Upgrade Figure 12 9 FTP Upgrade Interface 3 Enter the FTP Server Address in the text field 4 Click the Upgrade button to start upgrading 5 After the upgrading is complete reboot the device to activate the new firmware 197 User Manual of DS 7200 7300 8100 Series DVR 12 5 Restoring Default Settings Steps 1 Enter the Default interface Menu gt Maintenance gt Default System will reboot after restoring the default settings Continue Figure 12 10 Restore Factory Default 2 Click the OK button to restore the default settings fore Except the network parameters including IP address subnet mask gateway MTU and server port all other parameters of the device will be restored to factory default settings 198 User Manual of DS 7200 7300 8100 Series DVR Chapter 13 Others 199 User Manual of DS 7200 7300 8100 Ser
91. e patrol Calling Patrols Purpose The PTZ camera will move according to the predefined patrol path when you call a patrol Steps 66 User Manual of DS 7200 7300 8100 Series DVR 1 Click the button MEM in the lower right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting toolbar during the live view process or click PTZ Control on the right click menu to open the PTZ control panel in live view mode 2 Select the PTZ camera from the drop down list for control 3 Click the icon gt on the panel and then click the General tab to enter the general PTZ control interface 4 Select the patrol from the corresponding drop down list and then click the Call Patrol button to start the patrol 5 To stop the patrol you can click the button Stop Patrol on the panel PTZ Camera Analog 1 Configuration EI oe 4 One touch Call Preset Stop Pa 1 Call Patt Stop Pa 1 Figure 4 21 Control Panel Call Patrol Customizing Patterns Purpose A pattern is a memorized repeating series of pan tilt zoom and preset functions Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ 67 User Manual of DS 7200 7300 8100 Series DVR Analog 1 Clear All Clear All Stop Clear All Left Limit Right Limit RS 485 Setti Figure 4 22 PTZ Settings Customize Pattern Select the camera for PTZ setting from the
92. e system Yes No Figure 1 14 Dialog Box for Shutdown 3 Click the Yes button 4 Turn off the power switch on the rear panel of DVR Rebooting the device In the Shutdown menu Figure 1 13 you can also click Reboot to reboot the device 28 User Manual of DS 7200 7300 8100 Series DVR Chapter 2 Getting Started 29 User Manual of DS 7200 7300 8100 Series DVR 2 1 Using the Wizard for Basic Configuration The Setup Wizard can walk you through some important settings of the device By default the Setup Wizard starts once the device has loaded Operating the Setup Wizard 1l Selectthe system resolution from the drop down menu The default resolution is 1280x1024 60Hz Click Apply to save the resolution settings Resolution System Resolution 1280 10274 60HZ Cancel Figure 2 1 Start Wizard Interface By default the system resolution is set to 1280x1024 2 Check the checkbox to enable Setup Wizard when device starts Click Next to continue the setup wizard You can also click Cancel to exit the Setup Wizard or use the Setup Wizard next time by leaving the Start wizard when DVR starts checkbox checked and exit Wizard Start wizard when device starts Cancel Figure 2 2 Start Wizard Interface 30 User Manual of DS 7200 7300 8100 Series DVR 3 Click Next button on the Wizard window to enter the Login window as shown in Figure 2 3 Enter the admin password By default the password i
93. ecording mode When the HDD property is set to redundancy the video can be recorded both onto the redundancy HDD and the R W HDD simultaneously so as to ensure high security and reliability of video data Steps 1 Enterthe HDD Information interface Menu HDD General 2 Select HDD from the list and click the LA icon to enter the Local HDD Settings interface 178 User Manual of DS 7200 7300 8100 Series DVR Local HDD Settings HDD Property O R V Read only Redundancy Group ORE PIE FEE LEM LIE DIEM NAME E EE DIE BAR RPM EFES ECH BRE Rio 931GB Cancel Figure 10 13 Set HDD Property 3 Set the HDD property to R W Read only or Redundancy 4 Click the OK button to save the settings and exit the interface 5 Inthe HDD Information menu the HDD property will be displayed in the list ore At least 2 disks HDD or network disk must be installed or connected on your device when you want to set a HDD to Redundancy and there is one HDD with R W property 179 User Manual of DS 7200 7300 8100 Series DVR 10 4 Configuring Quota Mode Purpose Each camera can be configured with allocated quota for the storage of recorded files Steps 1 Enter the Storage Mode interface Menu HDD Advanced 2 Set the Mode to Quota fore The device must be rebooted to enable the changes to take effect Wiode Quota Camera Analog 1 Used Record Capacity 1 024MB HDD Capacily GB 931 Max Record Capacity
94. ed each time Log Search EAMinor Type MAlarm Output Start Motion Detection EAStop Motion Detection Start Video Tampering Detection Le Y T Side ew Taunan auma Pale aliaa No 2 3 4 5 Major Type nH Information Information Information information fh ian wwe whi oe Total 528 P 1 6 Log Export 12 27 2013 12 27 2013 All Time 12 27 2013 09 30 16 12 27 2013 09 30 16 12 27 2013 09 30 16 12 27 2013 09 30 16 AN ATF ANNAN AOWA AE 00 00 00 23 59 59 Minor Type Start Recording Start Recording Start Recording Start Recording P ouv e oe mw linn Paramet Play N A N A N A N A Abha Search Figure 12 3 Log Search Results 5 Youcan click the button of each log or double click it to view its detailed information And you can also click the e button to view the related video files 1f available Time Type Local User Host IP Address Parameter Type Camera No Description Log Information 12 27 2013 09 30 16 Information Start Recording N A N A N A Al Camera A1 starts recording Record status Record enabled Yes Event parameters Disabled Record type Manual Motion detected on camera None Alarm detected on camera None Previous Figure 12 4 Log Details 193 User Manual of DS 7200 7300 8100 Series DVR 6 If you want to export the log files click the Export button to enter the Export menu You can also export all
95. ed web server that one is communicating with and creates a secure channel over an insecure network HTTPS URLs begin with https and use port 443 by default You can modify the port No as desired Example If you set the port No as 445 and the IP address of the device is 192 0 0 64 you can access the device by inputting hitps 192 0 0 64 445 in the web browser Steps 1 Access the device via the web browser and enter the HTTPS settings interface Configuration gt Remote Configuration gt Network Settings gt HTTPS 2 Create the self signed certificate or authorized certificate 162 User Manual of DS 7200 7300 8100 Series DVR HTTPS Enable HTTPS Create Create Create Self signed Certificate Create Create Certificate Request Install Signed Certificate Certificate Path Created Request Created Request Installed Certificate Installed Certificate Figure 9 32 Figure 9 1 HTTPS Settings OPTION 1 Create the self signed certificate 1 Click the Create button and a dialog box pops up as follows Country CN example CN Hostname IP 172 6 23 67 Validity 20 Password State or province Locality Organization Organizational Unit Email Figure 9 33 Create Self signed Certificate 2 Enter the country host name IP validity and other information 3 Click OK to save the settings OPTION 2 Create the authorized certificate 1 Click the Create button to create th
96. en choose the channel to which you want to copy Copy to v Analog Al BA GAS BAs GAS ac MAT GAs iP Camera PIE py Figure 5 13 Copy Schedule to Other Channels E NOTE The IP camera is supported by the HDVR series only 4 Click Apply in the Record Schedule interface to save the settings 81 User Manual of DS 7200 7300 8100 Series DVR 5 3 Configuring Motion Detection Record Purpose Follow the steps to set the motion detection parameters In the live view mode once a motion detection event takes place the device can analyze it and perform some response actions to handle it Enabling motion detection function can trigger certain channels to start recording or trigger full screen monitoring audio warning notify the surveillance center and so on In this chapter you can follow the steps to schedule a record which triggered by the detected motion Steps 1 Enter the Motion Detection interface Menu Camera Motion Camera Enable Motion Settings Sensitivity Full Screen Clear aab es K Figure 5 14 Motion Detection 2 Configure Motion Detection Select the camera to configure 2 Check the checkbox after Enable Motion Detection Tun By default the motion detection is enabled and configured in full screen 3 Drag and draw the area for motion detection by mouse If you want to set the motion detection for all the area shot by the camera click Full Screen To clear the
97. ent image parameters so as to satisfy different light conditions e g daylight and night time Two periods can be configured When you have configured 45 User Manual of DS 7200 7300 8100 Series DVR Time Segment 1 the Time Segment 2 is remained as the Others 2 Select the mode from the drop down menu according to different light conditions Four modes are selectable Standard in general lighting conditions default Indoor the image is relatively smoother Dim Light the image is smoother than the other three modes o Outdoor the image is relatively clearer and sharper The degree of contrast and saturation is high Image Settings Image Settings Time Seg 06 00 18 00 Time Seg Others Mode Standard Mode Dim Light E w o Q Restore Copy Restore Copy Figure 3 5 Image Settings 3 Adjust the image parameters including the brightness contrast saturation hue sharpness level and denoising level by moving the sliding bar or increasing decreasing the value fore The adjustable value range is 0 255 for the brightness contrast saturation and hue 0 15 for the sharpness level and 0 5 for the denoising level 4 Copy image parameters You can click the Copy button to enter the Copy to interface to copy the image parameters of the current camera to other analog camera s cuc You can click the Restore button to restore the current image settings to default parameters Task2 Configure image settings
98. er Days t yore The Holiday option is available in the Schedule dropdown list when you have enabled holiday schedule in Holiday Settings Refer to Chapter 5 6 Configuring Holiday Record 79 User Manual of DS 7200 7300 8100 Series DVR Holrday1 By Date 2012 02 07 2012 02 08 Apply Figure 5 11 Holiday Settings 6 Click OK to save setting and back to upper level menu Task 2 Draw the Schedule Steps 1 Click the icon on the right to select a record type Different recording types are available for different models The VCA recording type is supported by the Smart DVR HDVR series only The Alarm Motion Alarm and Motion amp Alarm recording types are supported by the DS 7224 7232 DS 7300 and DS 8100 series only uada Nore To enable Motion triggered recording you must configure the motion detection settings For detailed information refer to Chapter 8 1 and Chapter 8 2 2 Use the mouse to drag and draw time periods ers Up to 8 periods can be configured for each day Analog 1 8 10 Edit Continuous Event Motion Alarm MIA LET VCA None Note Operation is invalid when the number of time segments exceeds the limit 8 Figure 5 12 Draw the Schedule 80 User Manual of DS 7200 7300 8100 Series DVR 3 You can repeat the above steps to set schedule for other channels If the settings can also be used to other channels click Copy to enter the Copy Camera interface and th
99. era s Remote PTZ Control Remotely controlling PTZ movement of the selected camera s Local Video Export Locally exporting recorded files of the selected camera s You should select the camera s on the Camera Configuration interface for the operation permission configured 7 Click the OK button to save the settings and exit interface me Only the admin user account has the permission of restoring factory default parameters 13 5 2 Deleting a User Steps 1 Enter the User Management interface Menu Configuration User 2 Select the user to be deleted from the list 206 User Manual of DS 7200 7300 8100 Series DVR Admin 00 00 00 00 00 00 Guest 00 00 00 00 00 00 Figure 13 9 Delete a User 3 Click the LJ icon to delete the selected user 13 5 3 Editing a User Steps 1 Enter the User Management interface Menu Configuration User 2 Select the user to be edited from the list 00 00 00 00 00 00 00 00 00 00 00 00 Figure 13 10 Edit a User 3 Click the LA icon to enter the Edit User interface 207 User Manual of DS 7200 7300 8100 Series DVR Edit User test zante settee Operator 00 00 00 00 00 00 Cancel Figure 13 11 Edit User Interface 4 Edit the user information including user name password level and MAC address S Click the OK button to save the settings and exit the menu 13 5 4 Changing Password of Admin Purpose The pass
100. ess The Email address of user to be notified Enable Attached Pictures Check the checkbox of Enable Attached Picture if you want to send email with attached alarm images Interval The interval refers to the time between two actions of sending attached pictures 126 smtp com 25 test01 test01 126 com Receiver 1 test02 test02 163 com 2s Figure 9 37 Configure Email Settings Click the Apply button to save the Email settings You can click the Test button to test whether your Email settings work The corresponding Attention message box will pop up Attention Attention Failed to send test email please check the parameters or network status OK OK Figure 9 38 Email Testing Attention 165 User Manual of DS 7200 7300 8100 Series DVR 9 3 Checking Network Traffic Purpose You can check the network traffic to obtain real time information of device such as linking status MTU sending receiving rate etc Steps 1 Enterthe Network Traffic interface Menu Maintenance Net Detect Network Detection Network Stat 32Kbps LAN1 Sending 3Kbps Receiving 2Kbps Name Linking Sta Type MAC Address MTU B NIC Type Traffic Im Figure 9 39 Network Traffic Interface 2 You can view the sending rate and receiving rate information on the interface The traffic data is refreshed every 1 second 166 User Manual of DS 7200 7300 8100 Series DVR 9 4 Network Detection Purpose You can obtain network
101. figure the parameters for the sub stream Refer to the step of main stream settings 3 Click Apply to save the settings NOTE You can click the Restore button to restore the current sub stream settings to the default parameters 4 If you want to copy the current sub stream settings to other camera s click Copy to enter the Copy Camera interface Select the camera s and click OK to finish the copy settings TI User Manual of DS 7200 7300 8100 Series DVR 5 2 Configuring Record Schedule Purpose Set the record schedule and then the camera automatically starts stops recording according to the configured schedule Steps 1 Enter the Record Schedule interface Menu gt Record gt Schedule 2 Configure Record Schedule 1 Click Schedule to enter the record schedule settings interface Analog 1 8 10 Edit Continuous Event Motion Alarm MIA Musa VCA None Figure 5 7 Record Schedule Normal recording Continuous Event Recording triggered by Motion Recording triggered by motion arm 1 alarm MIA Recording triggered by Recording triggered by H either motion or alarm both motion and alarm VCA Recording triggered by Delete the set schedule E VCA alarm Figure 5 8 Recording Types a nore The VCA recording type is supported by the Smart DVR HDVR series only 2 Choose the camera you want to configure 3 Check the check box after the Enable Schedule item There are two ways to configure the rec
102. for the IP camera Steps 1 On the Image Settings menu you can set the image parameters including the brightness contrast saturation and hue in the Custom mode 46 User Manual of DS 7200 7300 8100 Series DVR Image Settings Custom ES w E E c I Figure 3 6 Image Settings Customize 2 Click OK to save the settings 47 User Manual of DS 7200 7300 8100 Series DVR 3 3 Configuring Live View Settings Purpose Live View settings can be customized according to different needs You can configure the output interface dwell time for screen to be shown mute or turning on the audio the screen number for each channel etc Steps 1 Enter the Live View Settings interface Menu Configuration Live View View Channel Zero Encoding Video Output Interface GASHDMI Live View Mode 4 4 Dwell Time No Switch Enable Audio Output E Event Output GA HDMI Full Screen Monitoring D 10s Figure 3 7 Live View General The settings available in this menu include Video Output Interface Select the output to configure the settings for The following interfaces are selectable VGA HDMI Main CVBS and Spot Output 1 fore The Spot Output 1 is provided for DS 7300 and DS 8100 models Live View Mode Select different window division mode from the drop down list For the DS 7232 DS 7332 and DS 8132 models 1 4 6 8 9 16 25 36 division window display modes are supported for the DS 7224 DS 7324 DS 81
103. get the latest status of the port mapping Enable UPnP Mapping Type Auto Port Type Edit External Pot External IP Address UPnP Status HTTP Port 80 80 Inactive RTSP Port 994 0 554 Inactive Server Port 8000 MEIE HTTPS Port 443 443 inactive Refresh Figure 9 22 UPnP Settings Finished Auto Task2 Manual If you select Manual as the mapping type you can edit the external port on your demand by clicking E to activate the External Port Settings dialog box Steps 1 Click LA to activate the External Port Settings dialog box Configure the external port No for server port http port RTSP port and https port respectively fore You can use the default port No or change it according to actual requirements External Port indicates the port No for port mapping in the router The value of the port No should be between 1 and 65535 and the value must be different from each other If multiple devices are configured for the UPnP settings under the same router the value of the port No for each device should be unique External Port Settings Server Port 8001 Figure 9 23 External Port Settings Dialog Box 2 Click Apply to save the settings 3 You can click Refresh to get the latest status of the port mapping 158 User Manual of DS 7200 7300 8100 Series DVR Manual Port Type External Port Mapping IP Address Status HTTP Port 80 172 6 21 31 Active RTSP Port 554 172 6 21 31 55 Active HTTPS Port 443 1
104. gure the Intrusion Detection 1 Select the intrusion region from the drop down list Up to 4 regions are selectable 2 Select the sensitivity of the intrusion detection to 1 100 3 Set the percentage to 1 100 Percentage defines the ratio of the in region part of the object which can trigger the alarm For example when you set the percentage as 50 half of the object entering the region will trigger the alarm Analog 1 Intrusion Detection e Intrusion Region1 Figure 8 21 Set Intrusion Detection 4 Set the time threshold to 0 10 sec When the duration of the object in the defined detection area is 140 User Manual of DS 7200 7300 8100 Series DVR longer than the set time the alarm will be triggered 5 Click and draw a quadrilateral or click to draw the full screen in the preview window for the selected intrusion region You can use the E to clear the existing region and re draw it 6 Repeat the above steps to set other intrusion regions 7 Click Apply to save the settings 141 User Manual of DS 7200 7300 8100 Series DVR 9 6 Handling Exceptions Purpose Exception settings refer to the handling method of various exceptions e g HDD Full The HDD is full HDD Error Writing HDD error unformatted HDD etc Network Disconnected Disconnected network cable P Conflicted Duplicated IP address Illegal Login Incorrect user ID or password Input Output Video Standard Mismatch I O video st
105. he United States and or other countries HDMI HDMI mark and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC The products contained in this manual are authorized by HDMI Licensing LLC with the use right of the HDMI technology FICUTI HIGH DEFINITION MULTIMEDIA INTERFACE VGA is the trademark of IBM UPnP is a certification mark of the UPnP Implementers Corporation Other names of companies and product contained in this manual may be trademarks or registered trademarks of their respective owners User Manual of DS 7200 7300 8100 Series DVR Thank you for purchasing our product If there is any question or request please do not hesitate to contact dealer This manual is applicable to the following models DS 7204HFI SH DS 7208HFI SH DS 7216HFI SH DS 7204HWI SH DS 7208HWI SH DS 7216HWI SH DS 7204HVI SV DS 7208HVI SV DS 7216HVI SV Network HDVR Network DVR DS 8124HFSI SH DS 8132HFSI SH DS 8124HWSI SH DS 8132HWSI SH DS 7204HWI EI C DS 7208HWI E2 C DS 7216HWI E2 C DS 7304HWI E4 C DS 7308HWI E4 C DS 7316HWI EA C DS 8104HWI EA C DS 8108HWI ES C DS 8116HWI E8 C DS 7204HWT E1 DS 7208HWI E1 DS 7216HWI E1 DS 7208HWI E2 DS 7216HWI E2 DS 7304HWI SH DS 7308HWI SH DS 7316HWI SH Smart DVR HDVR DS 7224HWI E2 DS 7324HWI SH DS 7332HWI SH DS 8124HWSI SH DS 8132HWSI SH This manual may contain several technically incorrect places or printing errors and th
106. he following parameters for the Main Stream Continuous and the Main Stream 75 User Manual of DS 7200 7300 8100 Series DVR 4 Event Stream Type Set the stream type to be Video or Video amp Audio Resolution Set recording at resolution of WD1 4CIF 2CIF CIF or QCIF Bitrate Type Set the bitrate type to be Variable or Constant Video Quality Set the video quality of recording with 6 levels configurable NOTE e The WDI resolution is supported by DS 7204HWI SV DS 7224 7232HVI SH DS 7200HWI SH DS 7200HVI SV DS 7200HWI SL DS 7200HWI E1 2 C DS 7200HWI E1 E2 DS 7300HWI SH DS 7300HI SH DS 7300HWI E4 C DS 8 1OOOHWI E4 8 C DS 8100HCI SH and DS 8100HWSI SH models e The Stream Type Resolution Bitrate Type and Video Quality are not configurable for the Main Stream Event of the IP Camera e The selectable resolution for the IP camera is determined by the camera type please refer to the Appendix List of Compatible Hikvision IP Cameras up to 720P resolution is supported by 4 ch HDVR and 1080P resolution by 8 ch 16 ch HDVR Frame Rate Set the frame rate of recording Max Bitrate Mode Set the mode to General or Customize 32 3072Kbps Max Bitrate Kbps Select or customize the maximum bit rate for recording Max Bitrate Range Recommended A recommended Max bitrate range is provided for reference Configure the pre record post record time expired time redundant record this option is only available whe
107. he inner ring will move the selection up and down the outer ring will move it left and right In Playback mode the inner ring is used to jump 30s forward backward in video files The outer ring can be used to speed up slow down the video In Live View mode it can be used to cycle through different channels In PTZ control mode in can control the movement of the PTZ camera 18 User Manual of DS 7200 7300 8100 Series DVR 1 2 IR Remote Control Operations The device may also be controlled with the included IR remote control shown in Figure 1 4 fore Batteries 2xAAA must be installed before operation Figure 1 4 Remote Control Table 1 4 Description of the IR Remote Control Buttons POWER Power on off the device Enables Disables Remote Control Alphanumeric Buttons Switching to the corresponding channel in Live view or PTZ Control mode Inputting numbers and characters in Edit mode Switching between different channels in All day Playback mode EDIT Button Editing text fields When editing text fields it will also function as a Backspace button to delete the character in front of the cursor On checkbox fields pressing the EDIT button will tick the checkbox In Playback mode it can be used to generate video clips for backup 5 A Button Switching between input methods upper and lowercase alphabet symbols and numeric input REC Button Entering the Manual Record settings menu 19 User Manual of DS 7
108. holiday schedule and normal day schedule are displayed Repeat the above steps4 7 to set Holiday schedule for other channel If the holiday schedule can also be used to other channels click Copy and choose the channel you want to apply the settings 9 User Manual of DS 7200 7300 8100 Series DVR 5 7 Configuring Redundant Record Purpose Enabling redundant recording which means saving the record files not only in the R W read write HDD but also in the redundant HDD will effectively enhance the data safety and reliability aH nore You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property to Redundant For detailed information please refer to Chapter 10 4 Managing HDD Group There should be at least another HDD NetHDD which is in R W mode Steps 1 Enter HDD Information interface Menu gt HDD Figure 5 31 HDD General 2 Select the HDD and click A to enter the Local HDD Settings interface 1 Set the HDD property to Redundant Local HDD Settings HDD No HDD Property RW Read only O Redundancy Group REE DIEM FEE CEE LM LES ESE ED EE ELE DIE RPM EFES ECE FEN Mo HDD Capacity 931 51GB Cancel Figure 5 32 HDD General Editing 2 Click Apply to save the settings 3 Click OK to back to the upper level menu 3 Enter the Record setting interface Menu gt Record gt Parameters 1 Select Record 92 substream Camera Encoding Parameters Stream Ty
109. ideo output o 13 Ne RS 485 termination switch Up position is not terminated Termination Switch i Down is terminated with 120Q resistance RS 485 Interface Connector for RS 485 devices Connect the T and T terminals to the R and R terminals of PTZ receiver respectively 14 KB Connect the D and D terminals to Ta and Tb terminals of the controller For cascading devices the first DVR s D and D terminals should be connected with the D and D terminals of the next DVR Switch for turning on off the device 2 User Manual of DS 7200 7300 8100 Series DVR 1 6 Starting Up and Shutting Down the Device Purpose Proper startup and shutdown procedures are crucial to expanding the life of the device Before you start Check that the voltage of the extra power supply is the same with the device s requirement and the ground connection is working properly Starting up the device Steps 1 Check the power supply is plugged into an electrical outlet It is HIGHLY recommended that an Uninterruptible Power Supply UPS be used in conjunction with the device 2 Press the POWER button on the rear panel The Power indicator LED should turn green indicating that the unit begins to start up Shutting down the device Steps 1 Enter the Shutdown menu Menu Shutdown Shutdown 0 Shutdown Reboot Cancel Figure 1 13 Shutdown Menu 2 Click the Shutdown button to enter the following dialog box Attention Shut down th
110. ies DVR 13 1 Configuring General Settings Purpose You can configure the BNC output standard VGA HDMI output resolution mouse pointer speed etc Steps 1 Enter the General Settings interface Menu gt Configuration gt General 2 Select the General tab DST Settings More Settings Language English CVBS Output Standard NTSC Resolution 1024 768 60HZ Time Zone GMT 08 00 Beijing Urumgqi Singapore Date Format MM DD YYYY System Date 12 27 2013 System Time 14 14 15 Mouse Pointer Speed Enable Wizard Enable Password Figure 13 1 General Settings Interface 3 Configure the following settings Language The default language used is English CVBS Output Standard Select the CVBS output standard to NTSC or PAL which must be the same with the video input standard Resolution Select the VGA HDMI output resolution which must be the same with the resolution of the monitor screen Time Zone Select the time zone Date Format Set the date format System Date Select the system date System Time Set the system time Mouse Pointer Speed Set the speed of mouse pointer 4 levels are configurable Enable Wizard Enable disable the Wizard when the device starts up Enable Password Enable disable the use of the login password 4 Click the Apply button to save the settings 200 User Manual of DS 7200 7300 8100 Series DVR 13 2 Configuring RS 232 Serial Port S nore The RS 232 serial port
111. iew settings can only be configured by the local operation of HDVR Different camera orders and window division modes can be set for different output interfaces separately and digits like D1 and D2 stands for the channel number and X means the selected window has no image output 3 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from our company to do the further process Live view stuck when video outputs locally Possible Reasons a Poor network between device and IPC and there exists packet loss during the transmission b The frame rate has not reached the real time frame rate Steps 1 Verify the network between device and IPC is connected 1 When image is stuck connect the RS 232 ports on PC and the rear panel of device with the RS 232 cable 215 User Manual of DS 7200 7300 8100 Series DVR 2 Open the Super Terminal and execute the command of ping 792 168 0 0 1 1472 f the IP address may change according to the real condition and check if there exists packet loss nore Simultaneously press Ctrl and C to exit the ping command 2 Check the parameters of Main Stream Continuous and Main Stream Event Select Menu gt Record gt Parameters gt Record and set the resolution of Main Stream Event the same as the one of Main Stream Continuous 3 Verify the frame rate is real time frame rate
112. iles Purpose The record files stored in the external storage devices e g USB flash drives USB HDDs can be searched and played back Before you start Insert the external device s with available record files into the device Steps 1 Enter the Playback interface Menu Playback 2 Click and select INMIZUEMI to enter the External File Playback interface 112 User Manual of DS 7200 7300 8100 Series DVR The files stored in the extrenal device are listed in the right side list You can click the Refresh button to refresh the file list 8 3 Select a record file and click to play it External File E player exe ch01_201307 Figure 6 19 Interface of External File Playback 113 User Manual of DS 7200 7300 8100 Series DVR 6 2 Auxiliary Functions of Playback 6 2 1 Playing Back Frame by Frame Purpose Play video files frame by frame in order to check image details of the video when abnormal events happen Steps Using a Mouse Go to Playback interface If you choose playback of the record file click button ELI until the speed changes to Single frame and one click on the playback screen represents playback of one frame If you choose adverse playback of the record file click button ELI until the speed changes to Single frame and one click on the playback screen represents adverse playback of one frame It is also feasible to use button in toolbar Using the Front Panel Fo
113. including recording live view image settings switch to main monitor and no operation is allowed for the main output 4 To switch to the main vide output select the Main Monitor from the right click menu or use the mouse wheel to double click on the screen and then click Yes on the pop up message box _ NOTE You can select the Menu Output Mode under Menu gt Configuration gt More Settings to Auto or HDMI VGA and then restart the device to switch the main output back to HDMI VGA output 3 2 5 Quick Setting Toolbar in Live View Mode On the screen of each channel there is a quick setting toolbar which shows when you left click mouse on the camera 44 User Manual of DS 7200 7300 8100 Series DVR Figure 3 3 Quick Settings Toolbar Table 3 4 Description of Quick Setting Toolbar Icons Enable Manual Record T PTZ Control I Digital Zoom a Image Settings Instant Playback 3 Playback only shows the record in last five minutes If no record is found it means there is no record during the last five minutes Digital Zoom B Zoom can zoom in the selected area to the full screen You can left click and draw to select the area for zooming in as shown in Figure 3 4 Figure 3 4 Digital Zoom Image Settings Co nove Settings icon can be selected to enter the Image Settings menu Task1 Configure image settings for the analog camera Steps 1 Set the period of a day for configuring independ
114. io input DB15 connector for VGA output Display local video output and menu 24 User Manual of DS 7200 7300 8100 Series DVR 8 USB Interface Connects USB mouse or USB flash memory devices 9 LAN Interface RJ45 10M 100M 1000M Ethernet interface 11 Aer RS 485 termination switch Up position is not terminated Termination Switch Down is terminated with 120 resistance RS 485 Interface Connector for RS 485 devices Connect the T and T terminals to the R and R terminals of PTZ receiver respectively 12 KB Connect the D and D terminals to Ta and Tb terminals of the controller For cascading devices the first DVR s D and D terminals should be connected with the D and D terminals of the next DVR Switch for turning on off the device DS 8100 The rear panel of DS 8116 DVR is shown in Figure 1 11 3 4 5 6 7 8 910 11 12 13 14 17 Figure 1 11 Rear Panel of DS 8116 ES NOTE DS 8104 DS 8108 model provides 4 8 video and audio input interfaces on the rear panel and one LAN network interface Table 1 11 Description of Rear Panel a a RCA connector for audio output This connector is synchronized with VGA video output 6 RCA connector for two way audio input Connector for RS 232 devices 25 RCA connector for audio output This connector is synchronized with CVBS video output User Manual of DS 7200 7300 8100 Series DVR ih es DB15 connector for VGA output Displa
115. is disk when self evaluation is failed 1 Self test successful Short Test o 33 185 Pass Functional S M A R T Information Spin Up Time Start Stop Count Reallocated Sector Co Seek Error Rate Power on Hours Count Spin Up Retry Count Figure 10 19 S M A R T Settings Interface 182 User Manual of DS 7200 7300 8100 Series DVR 10 7 Detecting Bad Sector Purpose The bad sectors of a HDD may cause the system to slow down when reading or writing data You can detect the bad sectors of the HDD and thus to take immediate measures to repair it Steps 1 Enter the Bad Sector Detection interface Menu Maintenance HDD Detect gt Bad Sector Detection S M A R T Settings Detect 931 51GB 232MB Not tested Normal Damaged Figure 10 20 Bad Sector Detection 2 Select a HDD and click Detect to start detecting S M A R T Settings 931 51GB 232MB Testingj 1 0 Normal Damaged Figure 10 21 Bad Sector Detecting 3 You can click Pause to pause the detection and click Resume to resume the detection 4 If there is any error information about the HDD you can click Error info to view the information 183 User Manual of DS 7200 7300 8100 Series DVR 10 8 Configuring HDD Error Alarms Purpose You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal Steps 1 Enter the Exception interface Menu Configuration Exceptions select the Exception T
116. is recording it is red when the channel is in network transmission status it is pink when the channel is recording and transmitting Channel Status LED Indicators Alphanumeric Buttons Switch between different channels in All day Playback mode ZOOMm Button In PTZ control mode the ZOOM button is used to zoom in the PTZ camera Return to the Main menu after successful login MENU WIPER Turn off audible key beeper by pressing and holding the button for 5 seconds Start wiper if applicable in PTZ Control mode Switch to the corresponding channel in Live View or PTZ Control mode Exit and back to the previous menu ESC Arm disarm the DVR in live view mode Enter the Manual Record interface Turn audio on off in Playback mode BECOROUT In PTZ control mode pressing the REC SHOT button and a Numeric button will call a PTZ preset Adjust focus in the PTZ Control mode A FOCUS Switch between input methods upper and lowercase alphabet symbols and numeric input FILIGHT The FI LIGHT button when used in a list field will select all items on the list In PTZ Control mode it will turn on off PTZ light Input numbers and characters in Edit mode Enter the Playback menu n LAUD Auto scan in the PTZ Control mode Edit text fields When editing text fields it will also function as a Backspace button to delete the character in front of the cursor EDIT IRIS On checkbox fields pressing the button will tick the checkbox In P
117. itron protocol is selected all the other parameters like the baud rate data bit stop bit parity and flow control are not configurable 5 Click Copy if you want to configure same settings to other analog PTZ cameras 6 Click Apply to save the settings 63 User Manual of DS 7200 7300 8100 Series DVR 4 2 1 Setting PTZ Presets Patrols amp Patterns Before you start Make sure that the presets patrols and patterns should be supported by PTZ protocols Customizing Presets Purpose A preset is a predefined image position which contains information of pan tilt focus and other parameters You can customize the presets and the presets can be used with the event triggered action Steps 1 Enter the PTZ Settings interface Menu Camera gt PTZ Analog 1 Clear All 3 READ MEI TE xd 5 205 PI mt T a A h Jd EN pe a V d mo d ET XO mh Y 4 XD Ld APO zl s a 4 it at 3 1 EM y rh I WA NA a Stop Clear All N E UC P5245 n vm Patten j ET Clear All N xx near Scan MN Left Limit Right Limit RS 485 Setti Zoom FOCUS iis Figure 4 17 PTZ Settings Customize Preset 2 Select the camera for PTZ setting from the drop down list 3 Use the directional and zoom focus iris buttons on the PTZ control panel to steer the camera to the desired view 4 Input the preset No 1 255 in the Preset text field and then click the Set button under the Preset i
118. k Parameters Configuration 9 4 4 Checking Network Statistics Purpose You can check the network statistics to obtain the real time information of the device Steps 1 Enter the Network Statistics interface Menu gt Maintenance gt Net Detect 2 Click the Network Stat tab to enter the Network Statistics menu 169 User Manual of DS 7200 7300 8100 Series DVR Traffic Network Detection Type Remote Live View Remote Playback Net Total Idle Bandwidth 2 048Kbps Obps 118Mbps Refresh Figure 9 46 Network Stat Interface 3 View the bandwidth of Remote Live View bandwidth of Remote Playback bandwidth of Net Total Idle information 4 Click Refresh button to get the latest bandwidth statistics 170 User Manual of DS 7200 7300 8100 Series DVR Chapter 10 HDD Management 171 User Manual of DS 7200 7300 8100 Series DVR 10 1 Initializing HDDs Purpose A newly installed hard disk drive HDD must be initialized before it can be used with your device Steps 1 Enterthe HDD Information interface Menu gt HDD gt General Bil 1 93151GB Normal Local 906GB 931 51GB 906GB Figure 10 1 HDD Information Interface Select the HDD to be initialized 3 Click the Init button Initialize Initialization will erase all data on the HDD A Continue Cancel Figure 10 2 Confirm Initialization 4 Select the OK button to start initialization 5 After the HDD has been initialized the status
119. k interface Menu gt Playback 107 User Manual of DS 7200 7300 8100 Series DVR Select to enter the Tag Playback interface Select the channels from the list and specify the start time and end time for search Optionally you can input the keyword of the tag name in the Keyword text field to narrow the search Click Search and the tags matching the search conditions will be displayed on a list Click ll button to play back the file You can click the Back button to back to the search interface oo PS qu Pre play and post play time can be set according to actual needs NOTE Pre play time and post play time is added to the time point of the tag Tag M st x a TagName Play A1 A1 1 T Total 3 P 1 1 Pre play 30s Posi play 30s Back Figure 6 12 Interface of Playback by Tag Figure 6 13 Toolbar of Playback by Tag Table 6 1 Detailed Explanation of Playback by tag Toolbar dbi Mute Audio on Start Stop clipping Save clip s 5 Add default tag DH Add customized tag Digital Zoom 30s backward Pause Play Reverse NON NECS 108 User Manual of DS 7200 7300 8100 Series DVR NOTE Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames About video type bar B represents normal recording manual or schedule B represents event recording B represents smart search recording 6 1 5 Playing Back by Smart Search
120. kbox before the record files you want to back up fore The size of the currently selected files is displayed in the lower left corner of the window 119 User Manual of DS 7200 7300 8100 Series DVR Search result Eca Start End Time Size Play Lock E MA BA BA BA BA BA BA AI BA BA BA 07 19 2013 15 03 18 15 03 29 07 19 2013 15 07 51 15 08 03 07 19 2013 15 08 11 15 08 31 07 19 2013 15 08 42 15 09 03 07 19 2013 15 16 06 15 16 20 07 19 2013 15 16 31 15 16 52 07 19 2013 15 26 35 15 27 16 07 19 2013 15 28 47 15 28 57 07 19 2013 15 37 25 15 37 35 07 19 2013 15 38 18 15 38 31 07 19 2013 15 38 46 15 38 58 07 19 2013 15 51 31 15 51 43 07 19 2013 15 56 05 15 56 15 Total 27 P 1 1 Total size 0MB 463KB 595KB 3 996KB 4 228KB 3 630KB 5479KB 10 105KB 3 411KB 3 569KB 3 960KB 4 138KB 4 051KB 3 839KB s Ll s m s n n a Export All HDD 1 Start time 07 19 2013 15 02 32 End time 07 19 2013 15 02 44 Cancel Figure 7 5 Result of Normal Video Search for Backup 4 Export the record files Click Export button and start backup s Nore If the inserted device is not recognized Click the Refresh button e Reconnect device Check for compatibility from vendor You can also format USB flash drives or USB HDDs via the device USB writer SATA writer and eSATA HDD
121. m Host 4 Click the Apply button to save and exit the interface 160 User Manual of DS 7200 7300 8100 Series DVR 9 2 7 Configuring Multicast Purpose The multicast can be configured to realize live view for more than the maximum number of cameras through network A multicast address spans the Class D IP range of 224 0 0 0 to 239 255 255 255 It is recommended to use the IP address ranging from 239 252 0 0 to 239 255 255 255 Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network Select the More Settings tab to enter the More Settings interface 3 Set Multicast IP When adding a device to the CMS Client Management System software the multicast address must be the same as the device s multicast IP Alarm Host IP 1727 5 8 111 Alarm Host Port T200 Server Por 8000 HTTP Porl 80 Multicast IP 239 252 2 50 RTSP Porl 554 Figure 9 29 Configure Multicast 4 Click the Apply button to save and exit the interface 9 2 8 Configuring RTSP Purpose The RTSP Real Time Streaming Protocol is a network control protocol designed for use in entertainment and communications systems to control streaming media servers Steps 1l Enter the Network Settings menu by clicking Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings men Alarm Host IP 172 5 8 111 Alarm Host Port T200 Server Pon 8000 HTTP Port 80 Multicast IP 239 252 2 50 RTSP Port 554
122. meras by clicking the status bar before Analog to change it to EJ 3 Set recording mode to manual By default the camera is enabled with recording by schedule o y Click the ON status bar to change it to Ej and click again to enable the recording to manual ON on recording by schedule ON recording by manual operation fore After rebooting all the manual records enabled are canceled 4 Start all day continuous recording or all day motion detection recording of all channels 1 Click for Continuous or Motion Detection recording Attention Attention Start all day continuous recording of all Start all day motion detection recording channels of all channels Yes No Yes No Figure 5 27 Start Normal or Motion Detection Recording 2 Click Yes to enable all day continuous or motion detection recording of all channels 89 User Manual of DS 7200 7300 8100 Series DVR 5 6 Configuring Holiday Record Purpose You may want to have different plan for recording on holiday Follow the steps to configure the record schedule on holiday Steps 1 Enter the Record setting interface Menu gt Record 2 Choose Holiday on the left bar Holiday2 Disabled 1 Jan Holiday3 Disabled 1 Jan Holiday4 Disabled 1 Jan Holiday Disabled 1 Jan Holiday6 Disabled 1 Jan Holiday Disabled 1 Jan Holiday3 Disabled 1 Jan Holiday9 Disabled 1 Jan Holiday10 Disabled 1 Jan Holiday11 Disabled 1 Jan Holiday12 Disabled 1 Jan 2 3 4 5 6 7
123. monitor simultaneously Auto switch the screen is auto switched to the next one And you must set the dwell time for each screen on the configuration menu before enabling the auto switch Menu gt Configuration gt Live View gt Dwell Time Playback play back the recorded videos for current day s Start Recording start all day normal recording or motion detection recording for all channels Aux Main Output Switch the DVR will check the connection of the output interfaces to define the main and auxiliary output interfaces When both HDMI and VGA are connected or either one is connected it is used as the auxiliary video output for live view recording and PTZ controls When both HDMI and VGA are not connected it is used as the main video output for live view playback recording PTZ control and menu operations When the aux output is enabled you can do some basic operation on the live view mode for the Aux output while no operation is allowed for the main output 3 2 1 Front Panel Operation For the DS 7300 and DS 8100 models you can operate the front panel buttons to realize the following functions in live view Table 3 2 Front Panel Operation in Live View Functions Front Panel Operation Show single screen Press the corresponding Alphanumeric button E g Press 2 to display only the screen for channel 2 Show multi screen Press the PREV FOCUS button Manually switch Next screen right direction button screens Previou
124. n again Steps 1 Enter the Shutdown menu Menu Shutdown Shutdown 0 Shutdown Reboot Cancel Figure 3 11 Shutdown Menu 2 Click Logout NOTE After you have logged out the system menu operation on the screen is invalid It is required a user name and password to login the system 52 User Manual of DS 7200 7300 8100 Series DVR Chapter 4 PTZ Controls User Manual of DS 7200 7300 8100 Series DVR 4 1 Configuring PTZ Settings A S Nore This section is applied to the Network HDVR and Network DVR series Purpose Follow the procedure to set the parameters for PTZ The configuring of the PTZ parameters should be done before you control the PTZ camera Before you start For connection to the analog camera dome please check that the PTZ and the device are connected properly through RS 485 interface Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ gt General More Settings Analog 1 9600 8 1 Addre Address range 0 255 Figure 4 1 PTZ General 2 Choose the camera for PTZ setting in the Camera dropdown list 3 Enter the parameters of the PTZ camera fore All the parameters should be exactly the same as the PTZ camera parameters Only PTZ Protocol can be set for network cameras Example If the PTZ camera has a Baud rate as 115200 you should input 115200 in the Baud rate field 4 Click Copy if you want to configure same settings to other PTZ cameras 5 Cli
125. n the HDD mode is Group and whether you want to record audio Pre record The time you set to record before the scheduled time or event For example when an alarm triggered the recording at 10 00 if you set the pre record time as 5 seconds the camera records it at 9 59 55 Post record The time you set to record after the event or the scheduled time For example when an alarm triggered the recording ends at 11 00 if you set the post record time as 5 seconds it records till 11 00 05 Expired Time day The expired time is the longest time for a record file to be kept in the HDD if the deadline is reached the file will be deleted You can set the expired time to 0 and then the file will not be deleted The actual keeping time for the file should be determined by the capacity of the HDD Redundant Record Enabling redundant record means you save the record files in the redundant HDD See Chapter 5 7 Configuring Redundant Record E The Redundant Record option is only available when the HDD mode is Group The redundant record is used when you want to save the record files in the redundant HDD You must configure the redundant HDD in HDD settings For detailed information see Chapter 10 3 2 Setting HDD Property Record Audio Check the checkbox to record the sound or uncheck to record the image without sound Enable 960Mode Enable the encoding at WD1 PAL 960x576 NTSC 960x480 resolution for 76 User Manual of DS
126. n video locally while transmitting a lower resolution stream over the network The two streams are generated by the device with the main stream having a maximum resolution of 4CIF and the sub stream having a maximum resolution of CIF e DVR Acronym for Digital Video Recorder A DVR is device that is able to accept video signals from analog cameras compress the signal and store it on its hard drives e HDD Acronym for Hard Disk Drive A storage medium which stores digitally encoded data on platters with magnetic surfaces DHCP Dynamic Host Configuration Protocol DHCP is a network application protocol used by devices DHCP clients to obtain configuration information for operation in an Internet Protocol network e HTTP Acronym for Hypertext Transfer Protocol A protocol to transfer hypertext request and information between servers and browsers over a network e PPPoE PPPoE Point to Point Protocol over Ethernet is a network protocol for encapsulating Point to Point Protocol PPP frames inside Ethernet frames It is used mainly with ADSL services where individual users connect to the ADSL transceiver modem over Ethernet and in plain Metro Ethernet networks e DDNS Dynamic DNS is a method protocol or network service that provides the capability for a networked device such as a router or computer system using the Internet Protocol Suite to notify a domain name server to change in real time ad hoc the active DNS configuration of its co
127. nd other required information T NOTE Each item should be corresponding with the internal or external device port including server port http port RTSP port and https port 159 User Manual of DS 7200 7300 8100 Series DVR External Internal Delete Source Protocol Internal Source IP Source Application Port Port E Figure 9 26 Setting Virtual Server Item paia Nore The above virtual server setting interface is for reference only it may be different due to different router manufactures Please contact the manufacturer of router if you have any problems with setting virtual server 9 2 6 Configuring Remote Alarm Host Purpose With a remote alarm host configured the device will send the alarm event or exception message to the host when an alarm is triggered The remote alarm host must have the CMS Client Management System software installed Steps 1 Enterthe Network Settings interface Menu Configuration Network 2 Select the More Settings tab to enter the More Settings interface Figure 9 27 More Settings Interface 3 Enter Alarm Host IP and Alarm Host Port in the text fields The Alarm Host IP refers to the IP address of the remote PC on which the CMS Client Management System software e g 1VMS 4200 is installed and the Alarm Host Port must be the same as the alarm monitoring port configured in the software default port is 7200 1142 9 9 111 1200 8000 Figure 9 28 Configure Alar
128. nfigured hostnames addresses or other information stored in DNS e Hybrid DVR A hybrid DVR is a combination of a DVR and NVR e NTP Acronym for Network Time Protocol A protocol designed to synchronize the clocks of computers over a network e NTSC Acronym for National Television System Committee NTSC is an analog television standard used in such countries as the United States and Japan Each frame of an NTSC signal contains 525 scan lines at 60Hz e NVR Acronym for Network Video Recorder An NVR can be a PC based or embedded system used for centralized management and storage for IP cameras IP Domes and other DVRs e PAL Acronym for Phase Alternating Line PAL is also another video standard used in broadcast televisions systems in large parts of the world PAL signal contains 625 scan lines at 50Hz e PTZ Acronym for Pan Tilt Zoom PTZ cameras are motor driven systems that allow the camera to pan left and right tilt up and down and zoom in and out e USB Acronym for Universal Serial Bus USB is a plug and play serial bus standard to interface devices to a host computer 212 User Manual of DS 7200 7300 8100 Series DVR Troubleshooting No image displayed on the monitor after the device is starting up normally Possible Reasons a No VGA or HDMI connections b Connection cable is damaged c Input mode of the monitor is incorrect Steps 1 Verify the device is connected with the monitor via HDMI or VGA cable If
129. ng large data packages to the connected IPC and check if there exists packet loss NoTE Simultaneously press Ctrl and C to exit the ping command Example Input ping 172 6 22 131 1 1472 f 4 Verify the switch is not flow control Check the brand model of the switch connecting IPC and HDVR and contact with the manufacturer of the switch to check if it has the function of flow control If so please turn it down 5 Check if the fault is solved by the step 1 to step 4 If it is solved finish the process If not please contact the engineer from our company to do the further process When there is no monitor connected to the HDVR and you add the IPC via web browser the IPC status shows as Connected and then you connect the HDVR with the monitor via VGA or HDMI interface and reboot the device there is black screen with the mouse cursor Connect the HDVR with the monitor before startup via VGA or HDMI interface and manage the IPC to connect with the device locally or remotely the status of IPC displays as Connected And then connect the device with the CVBS and there is black screen either Possible Reasons After connecting the IPC to the HDVR the image is output via the main spot interface by default Steps Enable the output channel 2 Select Menu gt Configuration gt Live View gt View and select video output interface in the drop down list and configure the window you want to view NOTE The v
130. nnection is functioning properly ww numeral 1 rr Access the main menu interface Enter numeral 2 Enter letters ABC The F1 button can be used to select all items on the list 2ABC F1 In PTZ Control mode the F1 button can be used to zoom out zoom the PTZ camera In live view or playback mode the F1 button can be used to switch between main and spot video output Enter numeral 3 Enter letters DEF 3DEF F2 In PTZ Control mode the F1 button can be used to zoom in zoom the PTZ camera The F2 button can be used to cycle through tab pages Enter numeral 4 Enter letters GHP Exit and back to the previous menu 4GHI ESC Enter numeral 5 Enter letters JKL Delete characters before cursor Select the checkbox and ON OFF switch Start stop record clipping in playback SHIFT Switch of compound keys between the numeric letter input and functional control Enter numeral 6 Enter letters MNO In Playback mode it is used for direct access to playback interface SJKL EDIT 6MNO PLAY Enter numeral 7 Enter letters PQRS 7PQRS REC Manual record for direct access to manual record interface manually enable disable record Enter numeral 8 Enter letters TUV Access PTZ control interface 9WXYZ PREV 15 8TUV PTZ User Manual of DS 7200 7300 8100 Series DVR Function Description DIRECTION
131. not please connect the device with the monitor and reboot 2 Verify the connection cable is good If there is still no image display on the monitor after rebooting please check if the connection cable is good and change a cable to connect again 3 Verify Input mode of the monitor is correct Please check the input mode of the monitor matches with the output mode of the device e g if the output mode of DVR is HDMI output then the input mode of monitor must be the HDMI input And if not please modify the input mode of monitor 4 Check if the fault is solved by the step 1 to step 3 If it is solved finish the process If not please contact the engineer from our company to do the further process There is an audible warning sound Di Di Di Didi after a new bought device starts up Possible Reasons a No HDD iis installed in the device b The installed HDD has not been initialized c The installed HDD is not compatible with the device or is broken down Steps 1 Verify at least one HDD is installed in the device 1 Ifnot please install the compatible HDD E Please refer to the Quick Start Guide for the HDD installation steps 2 If you don t want to install a HDD select Menu gt Configuration gt Exceptions and uncheck the Audible Warning checkbox of HDD Error 2 Verify the HDD is initialized 1 Select Menu gt HDD gt General 2 Ifthe status of the HDD is Uninitialized please check
132. o Alarm Name llLocal 2 lllLocal 3 WLocal gt 4 Figure 8 26 Copy Settings of Alarm Output 145 User Manual of DS 7200 7300 8100 Series DVR 8 8 Triggering or Clearing Alarm Output Manually NOTE This section is available for DS 7224 7232 DS 7300 DS 8100 and HDVR models only Purpose Sensor alarm can be triggered or cleared manually If Manually Clear is selected in the dropdown list of dwell time of an alarm output the alarm can be cleared only by clicking Clear button in the following interface Steps Select the alarm output you want to trigger or clear and make related operations Menu gt Manual gt Alarm Click Trigger Clear button if you want to trigger or clear an alarm output Click Trigger All button if you want to trigger all alarm outputs Click Clear All button if you want to clear all alarm output Figure 8 27 Clear or Trigger Alarm Output Manually 146 User Manual of DS 7200 7300 8100 Series DVR Chapter 9 Network Settings 147 User Manual of DS 7200 7300 8100 Series DVR 9 1 Configuring General Settings Purpose Network settings must be properly configured before you operate device over network Steps for DS 7200 DS 7300 and DS 8104 8108 1 Enter the Network Settings interface Menu Configuration Network 2 Select the General tab NIC Type 10M 100M Self adaptive Enable DHCP iB v4 Address 172 6 23 P2 v4 Subnet Mask 255 255 255 0 v4 Default Gateway 172 6 2
133. of DS 7200 7300 8100 Series DVR NOTE Time periods shall not be repeated or overlapped 5 Select the Linkage Action tab to set alarm response actions of the alarm input please refer to Chapter 8 6 Settings Trigger Channel Linkage Action PTZ Linking Mon 10 00 24 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 o 6 6 6 6 6 O 6 Cancel Figure 8 9 Set Arming Schedule of Alarm Input 6 If necessary select PTZ Linking tab and set PTZ linkage of the alarm input Set PTZ linking parameters and click Apply to save the settings Click OK to complete the settings of the alarm input cn NOTE Please check whether the PTZ or speed dome supports PTZ linkage One alarm input can trigger presets patrol or pattern of more than one channel But presets patrols and patterns are exclusive Settings Trigger Channel Arming Schedule Linkage Action Analog 1 E Cancel Figure 8 10 Set PTZ Linking of Alarm Input 7 If you want to set the alarm response actions of another alarm input repeat the above steps or just copy the above settings to it by clicking Copy in Alarm Input Settings interface 134 User Manual of DS 7200 7300 8100 Series DVR Copy Alarm Input to lllAlarm input No Alarm Name lllLocal 2 lllLocal 3 lllLocal 4 lllLocal 5 lllLocal 6 lllLocal 7 lllLocal 8 lllLocal 9 lllLocal 10 MLocal lt 11 Cancel Figure 8 11 Co
134. of the HDD will change from Uninitialized to Normal 172 User Manual of DS 7200 7300 8100 Series DVR Figure 10 3 HDD Status Changes to Normal Iri Initializing the HDD will erase all data on it 173 User Manual of DS 7200 7300 8100 Series DVR 10 2 Managing Network HDD Purpose You can add the allocated NAS or disk of IP SAN to device and use it as network HDD Steps 1 Enter the HDD Information interface Menu HDD General HDD Information m 1 931 51GB Normal Local 906GB 931 51GB 906GB Figure 10 4 HDD Information Interface 2 Click the Add button to enter the Add NetHDD interface as shown in Figure 10 5 Add NetHDD NetHDD NetHDD 1 Type NAS NetHDD IP Address NetHDD Directory Search Cancel Figure 10 5 Adding NetHDD Interface 3 Add the allocated NetHDD 4 Select the type to NAS or IP SAN 174 User Manual of DS 7200 7300 8100 Series DVR 5 Configure the NAS or IP SAN settings Add NAS disk Enter the NetHDD IP address in the text field 2 Click Search to search the available NAS disks 3 Select the NAS disk from the list shown below Or you can just manually enter the directory in the text field of NetHDD Directory 4 Click the OK button to add the configured NAS disk fore Up to 8 NAS disks can be added Add NetHDD NetHDD 1 NAS 172 6 24 201 fdvridvr_ 1 Directory fdvridvr_ 2 fmntfbackup indexbackup Search Cancel Figure 10 6 Add NAS Di
135. on Steps 1 Enter the System Information interface Menu Maintenance System Info 2 Youcan click the Device Info Camera Record Alarm Network and HDD tabs to view the system information of the device Camera Device Name Model Serial No Firmware Version Encoding Yersion Record Network HDD Embedded Net DYR DS 7216HWI SH 1620121025AAWR201210134WCVU V 0 0 0 Build 000000 ORUM Build 000000 Figure 12 1 Device Information Interface 12 2 Searching amp Exporting Log Files Purpose The operation alarm exception and information of the device can be stored in log files which can be viewed and exported at any time Steps 1 Enter the Log Search interface Menu gt Maintenance gt Log Information gt Log Search Log Export EAMinor Type MAlarm Output 12 27 2013 00 00 00 12 27 2013 23 59 59 All MStar Motion Detection Stop Motion Detection Start Video Tampering Detection Lala LT Sida T anan anima Mamba ah oe No Major Type Time Minor Type Paramet Play Details Total 0 P 1 1 Search Figure 12 2 Log Search Interface 192 User Manual of DS 7200 7300 8100 Series DVR 2 Set the log search conditions to refine your search including the Start Time End Time Major Type and Minor Type 3 Click the Search button to start searching log files 4 The matched log files will be displayed on the list shown below fore Up to 2000 log files can be display
136. onditions This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement CE This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info User Manual of DS 7200 7300 8100 Series DVR Trademarks and Registered Trademarks Windows and Windows mark are trademarks or registered trademarks of Microsoft Corporation in t
137. ord files and downloading files broken transfer resume Remote parameters setup remote import export of device parameters Remote viewing of the device status system logs and alarm status Remote locking and unlocking of control panel and mouse Remote HDD formatting and program upgrading Remote system restart RS 232 and RS 485 transparent channel transmission s nore RS 232 serial port is provided for DS 7300 and DS 8100 models only Alarm event and exception information can be sent to the remote host Remotely start stop recording Upgrade by remote FTP server Remote PTZ control Two way audio and voice broadcasting Embedded WEB server Development Scalability SDK for Windows and Linux system Source code of application software for demo Development support and training for application system User Manual of DS 7200 7300 8100 Series DVR TABLE OF CONTENTS Product Rev Pea tines sco EE RUNE NINE MR MANI EMI MEda MR 6 Chapter I THEFOQOUCUOGDGO ssscasecscecasscacccacecstccasscasecacecstecasscasecacecstecasscasecacecasecasscasecacecatecasscasecases 13 1 1 EX ont P dB Erick net NIRE PRAE ERAN RADAR LURENUR ENEN EUR ANUR ERR ANO E Up ANUR ENEN 14 1 2 IK Remote Control Operations siio o e EE Recto ee tu Men o Po aaa 19 1 3 USB Mouse Operation sei eere a UR dat se hens qus e o GR ceca e oU ded 21 1 4 Input Method DeSctipEiOllc ore ten Rt E Ecce RE b E ERE REDE HL EUR 21 1 5 Rear Pale lt sn tates da MR MOM MR M
138. ord schedule Task 1 Edit the Schedule Steps 1 Click Edit 2 In the message box you can choose the day which you want to set schedule 3 To schedule an all day recording check Iv checkbox to enable all day recording 4 Set the Type in the dropdown list Different recording types are available for different models 78 User Manual of DS 7200 7300 8100 Series DVR The VCA recording type is supported by the Smart DVR HDVR series only The Alarm Motion Alarm and Motion amp Alarm recording types are supported by the DS 7224 7232 DS 7300 and DS 8100 series only t yore To enable Motion triggered recording you must configure the motion detection settings as well For detailed information refer to Chapter 8 1 and Chapter 8 2 Continuous 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Continuous Continuous Continuous Continuous 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Continuous Continuous Continuous LA E RE LE JE JE Continuous Cancel Figure 5 9 Edit Schedule 5 To arrange other schedule leave the All Day checkbox blank and set the Start End time and Type tl NOTE Up to 8 periods can be configured for each day And the time periods can t be overlapped each other Repeat the above steps2 5 to schedule recording for other days in the week If the schedule can also be set to other days click Copy Copy to v p E vE vE v Fi f Holiday Figure 5 10 Copy Schedule to Oth
139. pe Resolution Bitrate Type Video Quality Frame Rate Max Bitrate Mode Max Bitrate Kbps Max Bitrate Range Reco Pre record Post record xpired Time day Redundant Record Capt Record Audio Video Stream Analog 1 Main Stream Continuous Video amp Audio 704 576 ACIF Variable Medium Full Frame General 1792 1152 1920 Kbps 5s 5s 0 Main Stream 2 Select Camera you want to configure 3 Check the checkbox of the Redundant Record Nore User Manual of DS 7200 7300 8100 Series DVR Main Stream Event Video amp Audio 704 576 4ClF Variable Medium Full Frame General 1792 1152 1920 Kbps Figure 5 33 Encoding Record The Redundant Record option is only available when the HDD mode is Group The redundant record is used when you want to save the record files in the redundant HDD You must configure the redundant HDD in HDD settings For detailed information see Chapter 10 3 2 Setting HDD Property 4 Click Apply to save settings and back to the upper level menu 5 Repeat the above steps2 4 for configuring other channels 93 User Manual of DS 7200 7300 8100 Series DVR 5 8 Configuring HDD Group for Record Purpose You can group the HDDs and save the record files in certain HDD group Steps 1 Enter HDD setting interface Menu gt HDD Figure 5 34 HDD General 2 Select Advanced on the left bar Check whether the storage mode of the HDD is
140. periods can be set within each day 3 Click Apply to save the arming settings of the selected day 4 Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days fore Time periods shall not be repeated or overlapped Settings Trigger Channel Linkage Action Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 lt Figure 8 4 Set Arming Schedule of Motion Detection 5 Click the Linkage Action tab to set up alarm response actions of motion alarm please refer to Chapter 8 6 Settings Trigger Channel Arming Schedule Full Screen Monitoring E Audible Warning lll Notify Surveillance Center P Send Email E Trigger Alarm Output Figure 8 5 Set Alarm Response Actions of Motion Detection 131 User Manual of DS 7200 7300 8100 Series DVR The Trigger Alarm Output option is available for DS 7224 7232 DS 7300 DS 8100 and HDVR models only 6 Click OK to complete the motion detection settings of the channel 7 If you want to set up motion detection for another channel s repeat the above steps or copy the above settings to the channel s i NoTE You are not allowed to copy the Trigger Channel and Linkage Action settings Copy to Analog A1 A2 A3 A4 Ad A6 EAT GAS Figure 8 6 Copy Settings of Motion Detection 132 User Manual of DS 7200 7300
141. pport the VCA for the first and second analog cameras Analog 1 and Analog 2 3 Select the detection type to Line Crossing Detection or Intrusion Detection Line Crossing Detection This function can be used for detecting people vehicles and objects cross a set virtual line The line crossing direction can be set as bidirectional from left to right or from right to left And you can set the duration for the alarm response actions such as full screen monitoring audible warning etc Intrusion Detection This function can be used for detecting whether there are people vehicles and objects intruding into the pre defined region longer than the set duration And you can set the duration for the alarm response actions such as full screen monitoring audible warning 4 Check the Enable checkbox to enable the selected VCA detection 5 Click the to configure the trigger channel arming schedule and linkage actions 138 User Manual of DS 7200 7300 8100 Series DVR 1 2 nore Settings Arming Schedule Linkage Action WM Analog EXEEM TE BAS FU MIP Camera D1 Apply Cancel Figure 8 17 Set Triggering Channel of VCA Alarm Select Trigger Channel tab and select one or more channels which will start to record capture or become full screen monitoring when a VCA alarm is triggered and click Apply to save the Select Arming Schedule tab to set the arming schedule of handling actions Settings Trigger Channel Linkage Action
142. py Settings of Alarm Input 135 User Manual of DS 7200 7300 8100 Series DVR 9 3 Detecting Video Loss Purpose Detect video loss of a channel and take alarm response action s Steps 1 Enter Video Loss interface of Camera Management Menu Camera Video Loss Analog 1 Figure 8 12 Video Loss Setup Interface Select a channel you want to detect Check the checkbox of Enable Video Loss Alarm Click the icon of Settings to enter the Settings interface Dv v d Set the arming schedule and alarm response actions Please refer to Step4 and Step5 of Chapter 8 1 Setting up Motion Detection Alarm Settings Linkage Action Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Cancel Figure 8 13 Set Arming Schedule of Video Loss 6 Click Apply to save the video loss alarm settings 136 User Manual of DS 7200 7300 8100 Series DVR 9 4 Detecting Video Tampering Purpose Trigger alarm when the lens is covered and take alarm response action s Steps 1 Enter Video Tampering interface of Camera Management Menu Camera Video Tampering Detection Analog 1 Figure 8 14 Video Tampering Detection Setup Interface 2 Select a channel you want to detect video tampering 3 Check the checkbox of Enable Video Tampering Detection mE By default the video tampering detection is configured in full screen 4 Move the sensitivity ba
143. r DS 7300 and DS 8100 series DVR you can use the front panel buttons to perform the playback Rotate and hold the outer ring on Jog Shuttle counterclockwise or click the W button to set the speed to Single frame One click on buttonllll one click on the playback screen or Enter button on the front panel represents playback or reverse playback of one frame 6 2 2 Digital Zoom Steps 1 Enter the Playback interface and start the playback For details see Chapter 6 1 2 Click the icon on the playback control toolbar to enter Digital Zoom mode 3 Click and drag the mouse to draw a red rectangle on the window in the lower right corner of the interface And then the image within it will be enlarged up to 16 times 4 Right click to exit the Digital Zoom mode Qr gt Figure 6 20 Draw Area for Digital Zoom 114 User Manual of DS 7200 7300 8100 Series DVR 6 2 3 Reverse Playback of Multi channel Purpose You can play back record files of multi channel reversely Steps 1 Enter the Playback interface Menu gt Playback 2 Check checkbox to select the channel s and double click to select a date on the calendar NOTE If more than one channel is optional the synchronous playback will be activated Max Ca Min Ca Camera 01 Mosg Lv ler n TC 02 adis Lv Ter n TE 03 ER Plu lllCamera 06 L Camera 07 Camera 08 M Camera 09 M Camera 10 MCamera 11 lt 07 10 2013 16 08 07 ET 2013 17 04 02
144. r and choose a proper sensitivity level 5 Click the icon of Settings to enter the Handling interface 6 Set the arming schedule and alarm response actions Please refer to Step4 and Step5 of Chapter 8 1 Setting up Motion Detection Alarm 7 If you want to set video loss handling method for another channel repeat above steps or click Copy to copy the above settings to it Copy to Analog A1 A2 A3 A4 Ad A6 LTEM Fi Figure 8 15 Copy Settings of Video Tampering 137 User Manual of DS 7200 7300 8100 Series DVR 8 5 Detecting VCA Alarm Purpose The Smart DVR HDVR series can receive the VCA alarm sent by analog camera and the VCA detection must be enabled and configured on the camera settings interface first Perform the steps below to set the VCA configuration The device can provide VCA capability of enabling linkage actions when detecting exceptional event such as people vehicles and objects cross a virtual line or intrude a pre defined region Steps 1 Enter VCA Alarm interface of Camera Management and select a camera you want to detect VCA alarm Menu gt Camera gt VCA at Nore The selected camera must support the VCA function Analog 1 Line Crossing Detection FF 7 Figure 8 16 VCA Alarm Setting Interface 2 Select the analog camera to configure the VCA Nore The 4 ch Smart DVR HVR series support the VCA detection for the first analog camera Analog 1 and other Smart DVR HVR series su
145. ras 1 On the IP Camera interface the online cameras in the same network segment with the device can be detected and displayed on the list You can click the button Refresh to refresh the information of the online cameras am NOTE For the 4 ch HDVR 1 IP camera can be added and for the 8 ch and 16 ch HDVR 2 IP cameras can be added 35 User Manual of DS 7200 7300 8100 Series DVR IP Camera IP Camera Import Export Wcamera No Add Delete 3 IP Camera Address gt 172 6 23 3 1 2 6 235 124 Upgrade Delete Net Receive Idle Bandwidth 120Mbps Figure 2 12 IP Camera Management Upgrade Camera Name E Add All Custom Adding 2 Selecta camera from the list and click the icon to add it automatically Or click the button Add All to add all the online cameras automatically The user name and password are admin and 12345 by default 3 Optionally you can click the button Custom Adding to enter the Custom Adding interface Add IP Camera Custom IP Address Amount of Device M Protocol IP Camera Address 192 0 0 65 Protocol HIKVISION Management Port 8000 User Name Admin Password Search Manager Figure 2 13 Custom Adding of IP Camera Input the required information including the IP address management port user name and admin password and then click the button Add to add the camera manually 4 The successfully added IP cameras are listed in the interface 36 User Manual of
146. rd in video files The outer ring can be used to speed up slow down the video In Live View mode it can be used to cycle through different channels In PTZ control mode in can control the movement of the PTZ camera The front panel of DS 8100 is shown below C DEF GHI JKL MNO PQRS TUV WXYZ HHHHH0HHHR rec play A eon SHOT AUTO FOCUS IRIS G wENu F1 F2 WIN SPOT PREV PTZ WIPER UGHT AUX amp 200M Focus ms 4 8 9 10 Figure 1 3 Front Panel of DS 8100 16 User Manual of DS 7200 7300 8100 Series DVR Table 1 3 Description of Control Panel Buttons Function Description POWER ON OFF Power on off switch Receiver for IR remote control Connect to USB mouse or USB flash memory devices DVD R W Slot for DVD R W Alarm indicator turns red when a sensor alarm is detected Ready indicator is normally blue indicating that the DVR is functioning properly Indicator turns blue when DVR is controlled by an IR remote Indicator turns red when controlled by a keyboard and orange when IR remote and keyboard is used at the same time Indicator does not light when the DVR is controlled by the IR remote control with the address of 255 un i Indicator turns blue when the device is armed Indicator does not light when the device is disarmed The arm disarm state can be initiated by pressing and holding on the ESC button for more than 3 seconds in live view mode The button lights in blue when the corresponding channel
147. reate a new one NOTE If a new alias of the device domain name is defined in the DVR it will replace the old one registered on the server 153 User Manual of DS 7200 7300 8100 Series DVR HIDDNS www hik online com intelligent Figure 9 13 HiDDNS Settings Interface Register the device on the HiDDNS server 1 Goto the HiDDNS website www hik online com 2 Click Besistermewuset to register a user account if you do not have one 3 After registration is successful use the account and password to log in Figure 9 14 Register an Account 4 Inthe DDNS Management System interface click the Device Management tab on the left menu bar and then click aa to register the device Add Device dvri avice Serial No 0120514BBRR407966787VWCVU p Port 80 Figure 9 15 Register the Device g Note Only lower case English alphabet numeric and can be used in the alias of the device and the alias must be started with letters of the lower case English alphabet 5 Click the Apply button to save and exit the interface 154 User Manual of DS 7200 7300 8100 Series DVR 9 2 2 Configuring PPPoE Settings Purpose Your device also allows access by Point to Point Protocol over Ethernet PPPoE Steps 1 Iris Enter the Network Settings interface Menu Configuration Network Select the PPPoE tab to enter the PPPoE Settings interface Enable PPPOE User Name Password Figure 9 16
148. rface Steps 1 Enter the PTZ Control interface 2 Select the pattern number 3 Click then the PTZ moves according to the pattern Click o to stop it Pattern 1 f f HOoO O Figure 4 12 PTZ Calling Pattern Call pattern in live view mode Steps 1 In the live view mode press PTZ control on the IR remote control or click PTZ Control icon on the quick setting toolbar 2 And then choose Pattern on the control bar 3 Double click the pattern number you want to call or you can select the pattern number and click o to call the pattern PIZ pinhead afta Opera TOTES DUDSOGUTE Configuration BME 4 Patrol Figure 4 13 PTZ Toolbar Pattern 60 User Manual of DS 7200 7300 8100 Series DVR 4 2 2 PTZ Control Panel In the Live View mode you can press the PTZ Control button on the IR remote control or choose the PTZ Control icon a to enter the PTZ toolbar Figure 4 14 PTZ Toolbar Table 4 1 Description of the PTZ toolbar icons sc Direction button and the Zoom Focus Zoom Focus rarae auto cycle button Iris Iris The speed of the PTZ Wiper on off movement Image 3D Zoom Preset Centralization Start Light on off pattern patrol mm n Minimize windows Stop the patrol or pattern movement a mm tum EAM el Enter PTZ settings menu o EB o 61 User Manual of DS 7200 7300 8100 Series DVR 4 2 Configuring PTZ Settings B tl nore This section is applied
149. rm Input Alarm Output Alarm Input List Alarm Input No Alarm Name Alarm Type Local 2 N O Local 3 N O Local 4 N O Local 5 N O Local 6 N O acal lt 7 MO Alarm Output List Alarm Output No Alarm Name Dwell Time L l 2 Local 3 Local gt 4 172 6 23 3 8000 1 Figure 5 21 Alarm Settings 2 Click Alarm Input tab Alarm Status Alarm Input Alarm Output Local 1 1 N C o Figure 5 22 Alarm Settings Alarm Input 1 Select Alarm Input No and configure alarm parameters 2 Choose N O normally open or N C normally closed for alarm type 3 Check v checkbox to enable the alarm input 4 Click to set the alarm settings method 86 User Manual of DS 7200 7300 8100 Series DVR Settings Arming Schedule Linkage Action PTZ Linking P Analog LEM VEMM Fe DOREM DEM p LEM PL WIP Camera k Cancel Figure 5 23 Alarm Handling The IP Camera is supported by HDVR series only 5 6 7 8 9 Choose the alarm triggered recording channel Check the checkbox v to select channel Click Apply to save settings Click OK to back to the upper level menu Click Apply in the Alarm Input interface to save the settings Repeat the above steps to configure other alarm input parameters If the setting can also be applied to other alarm inputs click Copy and choose the alarm input number Copy Alarm Input to lllAlarm Input No Alarm Name Local lt 1 lllLocal 2 lllLo
150. ro Encoding 4 Configure the Frame Rate Max Bitrate Mode and Max Bitrate After you set the Channel Zero encoding you can get a view in the remote client or Web browser of all the channels in one screen 3 5 Manual Video Quality Diagnostics Purpose The video quality of the analog cameras can be diagnosed manually and you can view the diagnostic results from a list Steps 1 Enter the Manual Video Quality Diagnostics interface Menu Manual Manual Video Quality Diagnostics 2 Check the checkboxes to select the analog channels for diagnostics Click the button Diagnose and the results will be displayed on a list You can view the video status and diagnostics time of the selected channels 50 User Manual of DS 7200 7300 8100 Series DVR E Analog LEM LEES LUNES IOS DOREM DEM hv Diagnostics Result Camera No Diagnostics Result Diagnostics Time IB Te LETS ET Figure 3 10 Video Quality Diagnostics Connect the analog signal to the device for the video quality diagnostics Three exception types can be diagnosed Blurred Image Abnormal Brightness and Color Cast You can enter Menu Camera Video Quality Diagnostics to adjust the value of the Blurred Image Abnormal Brightness and Color Cast 51 User Manual of DS 7200 7300 8100 Series DVR 3 6 User Logout Purpose After logging out the monitor turns to the live view mode and if you want to do some operation you need to enter user name and password to log i
151. rs including Full Screen Monitoring Audible Warning Notify Surveillance Center and Send Email Full Screen Monitoring When an alarm event motion detection tamper proof video loss detection is triggered the local monitor HDMI VGA or BNC monitor display in full screen the video image from the alarming channel configured for full screen monitoring If alarms are triggered simultaneously in several channels their full screen images will be switched at an interval of 10 seconds default dwell time A different dwell time can be set by going to Menu Configuration gt Live View gt Full Screen Monitoring Dwell Time Auto switch will terminate once the alarm stops and you will be taken back to the Live View interface NOTE For motion detection alarm you must select the channel s you want to make full screen monitoring Menu gt Camera gt Motion gt Settings gt Trigger Channel Audible Warning Trigger an audible beep when an alarm is detected Notify Surveillance Center Sends an exception or alarm signal to remote alarm host when an event occurs The alarm host refers to the PC installed with Remote Client fore The alarm signal will be transmitted automatically at detection mode when remote alarm host is configured Please refer to Chapter 9 2 6 for details of alarm host configuration Send Email Send an email with alarm information to a user or users when an alarm event is detected Please refer to Chapter 9 2 11 for
152. s 12345 2 To change the admin password check the New Admin Password checkbox Enter the new password and confirm the password in the given fields E NOTE You are highly recommended to change the initial password right after the first login to avoid safety problem Wizard Previous Cancel Figure 2 3 Login Window 4 Click the Next button to enter the Date and Time settings window as shown in Figure 2 4 Set the time zone date format system date and system time Wizard GMI 0800 Being Urumqi Singapore MhM DD TYYY 06 24 2011 18 18 12 Previous Figure 2 4 Date and Time Settings 5 Click Next button which takes you back to the Network Setup Wizard window as shown in Figure 2 5 Set the network parameters including the NIC type IPv4 address IPv4 subnet mask default gateway etc You can enable the DHCP to automatically obtain an IP address and other network settings from that server 31 User Manual of DS 7200 7300 8100 Series DVR Wizard 10M 100M Self adaptive El 172 9 4 65 Pis GARS ioe dU Wizard Multi address LAN1 10M 100M 1000M Self adaptive m y 172 9 4 1 172 6 21 110 255 255 255 0 way 172 6 4 21 1 Previous Cancel Previous Cancel Figure 2 5 Network Configuration NOTE The DS 7204 7208 7216 models provide one 10M 100Mbps self adaptive network interface the DS 7224 7232 DS 7300 and DS 8104 8108 models provide one 1OM 100M 1000Mbps self adaptive network in
153. s of the Live View are also available while in an Aux monitor These features include 43 User Manual of DS 7200 7300 8100 Series DVR Single Screen Switch to the single full screen by choosing channel number from the dropdown list Multi screen Adjust the screen layout by choosing from the dropdown list Previous Screen Switch to the previous screen Next Screen Switch to the next screen Quick Set Set the video output mode to Standard Bright Gentle or Vivid Menu Output Mode Select the menu output mode to HDMI VGA Main CVBS or Auto Main Monitor Switch to the Main Output mode and the operation for the auxiliary output is disabled S NOTE In the live view mode of the main output monitor the menu operation is not available while Aux output mode is enabled 3 2 4 Main Aux Output Switching When the HDMI VGA output is configured as the main output you can perform the following operation to switch to CVBS output as the main output Steps 1 Use the mouse wheel to double click on the HDMI VGA output screen and the following message box pops up Tip Double click the mouse again to switch the auxiliary and main output Cancel Figure 3 2 Switch Main and Aux Output 2 Use the mouse wheel to double click on the screen again to switch to the Aux output or click Cancel to cancel the operation 3 On the aux output monitor you can do some basic operation on the live view mode for the Aux output
154. s screen left direction button Bicis ter buon All day playback Press Play button Switch main and aux Press F1 button and Enter button output 3 2 2 Using the Mouse in Live View In the live view mode use the mouse to right click on the window to access the following menu 42 User Manual of DS 7200 7300 8100 Series DVR Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch Start Recording Add IP Camera Quick Settings Playback PTZ Control Aux Monitor Figure 3 1 Right click Menu Table 3 3 Mouse Operation in Live View Start Stop Enable disable the auto switch of the screens Auto switch S NOTE The dwell time of the live view configuration must be set before using Start Auto switch Add IP Camera Enter the IP Camera Management interface to add the locally searched online IP camera quickly Quick Settings Set the video output mode to Standard Bright Gentle or Vivid Playback Play back the video of the selected channel PTZ Control Enter the PTZ control panel Aux Monitor Switch to the auxiliary output mode and the operation for the main output is disabled AMI oq you enter Aux monitor mode and the Aux monitor is not connected the mouse operation is disabled you need to use the mouse double click for twice to back to the Main output s The Add IP Camera item is provided by the HDVR models only 3 2 3 Using an Auxiliary Monitor Certain feature
155. sk Add IPSAN Enter the NetHDD IP address in the text field 2 Click the Search button to the available IP SAN disks 3 Select the IP SAN disk from the list shown below 4 Click the OK button to add the selected IP SAN disk mE Up to 1 IP SAN disk can be added 175 User Manual of DS 7200 7300 8100 Series DVR Add NetHDD NetHDD 1 IP SAN 172 9 2 210 iqn 2004 05 storos t 8 iqn 2004 05 storos t 41 iqn 2004 05 storos t 1000 Search Cancel Figure 10 7 Add IP SAN Disk 6 After having successfully added the NAS or IP SAN disk return to the HDD Information menu The added NetHDD will be displayed in the list fore If the added NetHDD is uninitialized please select it and click the Init button for initialization x 1 931 51GB Normal Local 906GB 1 17 40 000MB Normal IP SAN 22 528MB 1 E n Figure 10 8 Initialize Added NetHDD 176 User Manual of DS 7200 7300 8100 Series DVR 10 3 Managing HDD Group 10 3 1 Setting HDD Groups Purpose Multiple HDDs can be managed in groups Video from specified channels can be recorded onto a particular HDD group through HDD settings Steps 1 Enter the Storage Mode interface Menu HDD Advanced 2 Set the Mode to Group as shown below Mlode Group Record on HDD Group 1 iv Analog EL A1 Ev v PX Ad GAS m A6 GA GIP Camera I HD 2 Enable HDD Sleeping Figure 10 9 Storage Mode Interface eee NoTE The IP Camera is supported b
156. sstnrs 129 8 1 petting Monon DeeChOl anccan Gehan tenance tad 130 8 2 DSCNS DENS OL AIS tare E E in nob eben bad ats 133 8 3 Detecting Video Loss 38 3 d m ates dan an beoce aot dove arena iansdan ut osde e td 136 8 4 Detectine Video Tatlpettlig us oec ate eH tene Na nU E dac 137 8 5 Detecting VC ATARI cuc ao Coe Meese eA aes eaten 138 8 6 Pa ExcepHOollsguntsatessedeeti tende or pen Dub beide edebat te Dui tupd e ren dedo te 142 8 7 Setting Alarm Response Actions ccccccccccccceseeeesssssseseeeeeccceeeeeeeeaeeeeeeseees 144 8 8 Triggering or Clearing Alarm Output Manually esses 146 Chapter 9 Network Settings ace ece eo c e eve saa e o ses er DeL oe s sassteaceissssce assteacetssescesesseeaceessesss 147 9 Configuring General Settings sendien n nennen enne 148 9 2 Configuring Advanced Settings ccccccccssssssssssssseeeccceeeeeeeeceeaaaeessssseeeeeeeeess 151 22 1 Onis urine Extranet ACCESS e ode HERRERA E 151 2 22 Contieurmiie PPPOE SENES 33 osset s sus tl dg a dus Clap HOLT E dc VEA OPI es 155 29 2 2 C onfTeliEEHO INT D SOEVET ciui teret tpi Me EN Nora X DeEHDE PIE TE opu E RE molded 155 TAC One Urne SNM E usitato bita stu sehen bte lmuR ursa ebd ented eae aaa Onecah ade 156 9 2 5C ODITE UPS NAT enaa Loca iad er IUESEDRa seams od Mon ao aU P dou IO oe eats 157 9 2 6 Contisurime Remote Alarm Host encre te t t ee 160 9 2 Conte NDUO aS Hee IR rtu let b Em 161 9 2 5 Con suring RTSP aatis e td benda dd
157. t TAE E EAT ES EG SET e a 13 14 15 16 17 O Call Preset Pattern 1 fo oo Patrol 4 Figure 4 4 PTZ Call Preset 3 Choose the preset number NOTE For the DS 7200HWI E1 2 C DS 7300HWI E4 C and DS 8100HWI E4 8 C series you can call the preset 95 to enter the menu of the connected Coaxitron camera dome Use the directional buttons on the PTZ control panel to operate the menu For details please refer to the user manual of the camera dome Call preset in live view mode Steps 1 Click the PTZ Control icon og the quick setting bar to enter the PTZ setting menu in live view mode PTZ X Prenn TOSSES COESERESEEET Configuration Lv e ED B 4 Camera Preset Preset3 Preset4 PresetS Figure 4 5 PTZ Toolbar Call Preset 56 User Manual of DS 7200 7300 8100 Series DVR 2 Choose Camera in the list on the menu 3 Choose preset in the Preset list Customizing Patrols Purpose Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point The key points are corresponding to the presets The presets can be set following the steps above in Customizing Presets Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Select patrol number 3 Select the o under Patrol option box to add key points for the patrol Analog 1 O Save Preset que rpm agn ey ES T7 8 JT TT TZ TS
158. t recording file s in this day not current day Mouse cursor is located 06 04 2014 10 45 12 06 09 2014 17 36 27 Figure 6 4 Toolbar of All day Playback Detailed Explanation of All day playback Toolbar Mute Audio on Start Stop clipping Save clip s Pause Digital Zoom n Stop Play Reverse 102 User Manual of DS 7200 7300 8100 Series DVR Video type bar E ANM Normal playback Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames About video type bar L represents normal recording manual or schedule BI represents event recording B represents smart search recording 6 1 2 Playing Back by Time Purpose Play back video files recorded in specified time duration Multi channel simultaneous playback and channel switch are supported Steps 1 Enter playback interface Menu gt Playback 2 Check v checkbox of channel s in the channel list 3 Double click to select a date on the calendar to play back the record file fore If there are record files for that camera in that day in the calendar the icon for that day is displayed a Ml Otherwise it is displayed M 1124 3 4 benef Gelman o pejaojaajao 13 14 21 22 2324 25 26 27 28 Figure 6 5 Playback Calendar In the Playback interface The toolbar in the bottom part of Playback interface can be used to control playing process Please refer to Chapter 6
159. tem to save the preset 5 Repeat the steps 3 4 to save more presets 6 You can click the Clear button under the Preset item to clear the selected preset or click the Clear All button to clear all the presets 64 User Manual of DS 7200 7300 8100 Series DVR Calling Presets Purpose The view angle of the PTZ camera will be moved to the predefined position when you call a preset Steps 1 Click the button MMES in the lower right corner of the PTZ setting interface or press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting toolbar during the live view process or click PTZ Control on the right click menu to open the PTZ control panel in live view mode 2 Select the PTZ camera from the drop down list for control 3 Click the icon gt on the panel and then click the General tab to enter the general PTZ control interface 4 Input the preset No in the corresponding text field and then click the Call Preset button to call it PTZ Camera Analog 1 Configuration El oe 4 One touch 1 Call Patrol Stop Pa 1 Call Patt Stop Pa 1 Figure 4 18 PTZ Control Panel Call Preset fore For the DS 7200HWI E1 2 C DS 7300HWI E4 C and DS 8100HWI EF4 8 C series you can call the preset 95 to enter the menu of the connected Coaxitron camera dome Use the directional buttons on the PTZ control panel to operate the menu Customizing Patrols Purpose A patrol is a scanning
160. terface Nore The time synchronization interval can be set from 1 to 10080min and the default value is 60min If the device is connected to a public network you should use a NTP server that has a time synchronization function such as the server at the National Time Center IP Address 210 72 145 44 If the device is setup in a more customized network NTP software can be used to establish a NTP server used for time synchronization 9 2 4 Configuring SNMP Purpose You can use SNMP protocol to get device status and parameters related information Steps 1 Enterthe Network Settings interface Menu Configuration Network 2 Select the SNMP tab to enter the SNMP Settings interface SNMP Version SNMP Pon Read Community Write Community a alalgeled rap AGOreS5 Irap Port Figure 9 19 SNMP Settings Interface Check the SNMP checkbox to enable this feature Configure the SNMP settings 156 User Manual of DS 7200 7300 8100 Series DVR Enable SNMP SNMP Version VY SNMP Port 161 Read Community public Write Community private Irap Address Irap Port 162 Figure 9 20 Configure SNMP Settings S Click the Apply button to save and exit the interface n Nore Before setting the SNMP please download the SNMP software and manage to receive the device information via SNMP port By setting the Trap Address the device is allowed to send the alarm event and exception message to the surveillance center
161. terface and the DS 8116 8124 8132 models provide two10M 100M 1000Mbps self adaptive network interfaces 6 Click Next button to enter the advanced network settings window 7 Configure the advanced network parameters including the server port HTTP port RTSP port UPnP EZVIZ Cloud P2P and DDNS settings Wizard Server Port HTTP Port 80 RTSP Port Enable UPnP Enable EZVIZ Clou B Fs Ta liters eda B Code ABCDEF Enable DDNS a HIDDNS www hik online com Previous Figure 2 6 Advanced Network Configuration 8 Click Next button to enter the HDD Management window shown in Figure 2 7 To initialize the HDD click the Init button Initialization removes all the data saved in the HDD 32 User Manual of DS 7200 7300 8100 Series DVR Wizard 76 319MB Normal RAN Local 50 1 76MB Previous Cancel Figure 2 7 HDD Management 9 Click Next to enter the IP Camera Management window only supported by HDVR series Wizard lINo IP Address Amount of Device Ty Protocol Manage F Search Previous Figure 2 8 IP Camera Management 10 Click Search to search IP Camera Click Add to add IP Camera only supported by HDVR series 11 After finishing IP Camera settings Click Next to enter the Record Settings window 12 Click Next button to enter the Record Settings window as shown in Figure 2 9 1 Select the camera to configure 2 Check the checkbox to enable Start Recording 3 Select the recording mode
162. the log files stored in the HDD 1 Enter the Log Export interface Menu gt Maintenance gt Log Information gt Log Export Log Search E 1 931 51GB Normal Local Figure 12 5 Log Export Interface 2 Check w checkbox to select the HDD and click Export to enter the export interface USB1 1 Folder Folder Folder 20120525115558l0gB 13KB File B 20120525115625logB 13KB File 1 544MB New Folder Refresh 05 16 2012 09 47 50 05 16 2012 09 48 16 05 23 2012 13 43 08 05 25 2012 11 55 58 05 25 2012 11 56 25 Format Cancel Figure 12 6 Export Log Files 7 Select the backup device from the dropdown list of Device Name 8 Click the Export to export the log files to the selected backup device You can click the New Folder button to create new folder in the backup device or click the Format button to format the backup device before log export Cu Please connect the backup device to device before operating log export The log files exported to the backup device are named by exporting time e g 2011051412484 1logBack txt 12 3 Importing Exporting Configuration Files Purpose The configuration files of the device can be exported to local device for backup and the configuration files of one User Manual of DS 7200 7300 8100 Series DVR device can be imported to multiple device devices if they are to be configured with the same parameters Steps 1 Enter the Import Export Config
163. track specified by a group of user defined key points with the scanning speed between two key points and the duration time at each key point separately programmable The key points are corresponding to the presets Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ 65 User Manual of DS 7200 7300 8100 Series DVR Analog 1 Clear All Clear All Stop Clear All Left Limit Right Limit RS 485 Setti Figure 4 19 PTZ Settings Customize Patrol Select the camera for PTZ setting from the drop down list Select patrol number from the drop down list Click the button Set under the Patrol item to open KeyPoint settings interface 7i e D Im Configure key point parameters such as the preset No duration of staying for one key point and speed of patrol The key point is corresponding to the preset The Preset determines the order at which the PTZ will follow while cycling through the patrol The Duration refers to the time span to stay at the corresponding key point The Speed defines the speed at which the PTZ will move from one key point to the next KeyPoint KeyPoint 1 Preset Duration Cancel Figure 4 20 Key point Configuration 6 Click Add to save the current key point and then repeat the above steps to set the next one 7 Click OK to save the patrol settings 8 You can click the Clear button under the Patrol item to clear the selected patrol or click the Clear All button to clear all th
164. tte s X eris cee tort tence set awe ase bepdt eb ton Tui bucie de us dede 54 4 2 1 Setting PTZ Presets Patrols amp Patterns ccccccseceecccceeeeeeeeeeeeeeeeeees 54 4 2 2 PIZ Control Pane zoe iete utem cee voces A san Re emt m 61 4 2 Coufte rine PTZ Settinss B er BE e ees 62 4 2 1 Setting PTZ Presets Patrols amp Patterns cccccsscceeceeceeeeeeeeeeeeeeeeeeees 64 4 2 2 Connie Whine Linear Scal d ro eo eot ae scar eI dde I tene demas Las ode adi 69 4 2 3 One touch Pork aee oo ERE IDE RIDE DR RID NIDE RIDE UN NE 70 4 2 4 PTZ Contool Panel eese gem HENTAI NHS URNA SEHR ORA du MAE 71 Chapter 5 Record 9S6Elgs unie oaa ia aa DER RE F0 QER E Saa QUARE RE EQER E cscacansacencanccsvauanuesvocanucscacasiede s 73 5 1 Configuring Encoding Parameters a 74 3 2 Conlbts rine Iecord 5chedule ase oo Eee E o o PR ies a GRE ceed dina esta ees 78 5 3 Configuring Motion Detection Record cccccseeccceccecceceeeeeaeeesssssseeeeeeeees 82 5 4 Configuring Alarm Triggered Record isciani anina nain 86 5 5 Contigurine Manual Record e bote tr e eta beet dne dis 89 5 6 Conlte urimes Holiday RCC ORG uin secs cel ce RE E Rb a RM Ha TID E Ia INE 90 User Manual of DS 7200 7300 8100 Series DVR 5 7 Contisurine Redundant Record er i nr pee 92 5 8 Configuring HDD Group for Record esee 94 2 9 Pile S Protec Oi coco hio ERR HR EOD UR PI edente ede eode d AENA de noce 96 Chapter
165. ttings Remotely configuring parameters restoring factory default parameters and importing exporting configuration files Remote Camera Management Remotely enabling and disabling analog camera s and adding deleting and editing of network camera s This function is supported by HDVR series Remote Serial Port Control Configuring settings for RS 485 ports Remote Video Output Control Sending remote control panel signal Two Way Audio Realizing two way radio between the remote client and the device Remote Alarm Control Remotely arming notify alarm and exception message to the remote client and controlling the alarm output Remote Advanced Operation Remotely operating HDD management initializing HDD setting HDD property upgrading system firmware clearing I O alarm output Remote Shutdown Reboot Remotely shutting down or rebooting the device Camera Configuration Remote Live View Remotely viewing live video of the selected camera s Local Manual Operation Locally starting stopping manual recording picture capturing and alarm output of the selected camera s Remote Manual Operation Remotely starting stopping manual recording picture capturing and alarm output of the selected camera s Local Playback Locally playing back recorded files of the selected camera s Remote Playback Remotely playing back recorded files of the selected camera s Local PTZ Control Locally controlling PTZ movement of the selected cam
166. u Figure 1 2 Front Panel of DS 7300 Table 1 2 Description of Control Panel Buttons Name Function Description No POWER ON OFF Power on off switch Receiver for IR remote control Connect to USB mouse or USB flash memory devices 4 DVD R W Slot for DVD R W POWER Power indicator lights in green when DVR is powered up READY Ready indicator is normally green indicating that the DVR is functioning properly STATUS Indicator turns green when DVR is controlled by an IR remote control with the 14 User Manual of DS 7200 7300 8100 Series DVR No Name Function Description address from 1 254 Indicator turns red when the SHIFT button is used Indicator does not light when the DVR is controlled by a keyboard or by the IR remote control with the address of 255 Indicator turns green when the DVR is controlled by IR remote control with the address from 1 254 and keyboard at the same time and the SHIFT button is not used Indicator turns orange a when the DVR is controlled by IR remote control with the address from 1 254 and keyboard at the same time and the SHIFT button is used as well b when the DVR is controlled by IR remote control with the address from 1 254 and the SHIFT button is used ALARM Alarm indicator turns red when a sensor alarm is detected HDD HDD indicator blinks in red when data is being read from or written to HDD D TX Rx TX RX indictor blinks in green when network co
167. uration File interface Menu gt Maintenance gt Import Export Folder Folder Folder B 20120525115558logBack 13KB File B 20120525115625logBack 13KHB File New Folder Figure 12 7 Import Export Config File 05 16 2012 09 47 50 05 16 2012 09 48 16 05 23 2012 13 43 08 05 25 2012 11 55 58 05 25 2012 11 56 24 Import Export Refresh 2 Click the Export button to export configuration files to the selected local backup device 3 To import a configuration file select the file from the selected backup device and click the Import button After the import process is completed you must reboot the device mE After having finished the import of configuration files the device will reboot automatically 195 User Manual of DS 7200 7300 8100 Series DVR 12 4 Upgrading System Purpose The firmware on your device can be upgraded by local backup device or remote FTP server 12 4 1 Upgrading by Local Backup Device Steps 1 Connect your device with a local backup device where the update firmware file 1s located 2 Enter the Upgrade interface Menu Maintenance Upgrade 3 Click the Local Upgrade tab to enter the local upgrade menu Refresh Lone lll digicap mav 18 255KB File 2012 04 18 21 06 44 Figure 12 8 Local Upgrade Interface 4 Select the update file from the backup device 5 Click the Upgrade button to start upgrading 6 After the upgrading is complete reboot the device to activate th
168. utdoor the image is relatively clearer and sharper The degree of contrast and saturation is high Adjust the image parameters including the brightness contrast saturation hue sharpness and denoising level by moving the sliding bar or increasing decreasing the value cn NOTE When you select different mode corresponding default parameters are available You can also adjust the value of the brightness contrast saturation and hue to 0 255 the sharpness to O 15 and the denoising level to O 5 Youcan click the Copy button to copy the image settings of the current camera to other cameras Please refer to step 7 of Chapter 11 1 Configuring OSD Settings On the Image Settings interface click the Apply button to save the settings ft 188 User Manual of DS 7200 7300 8100 Series DVR 11 4 Configuring Video Quality Diagnostics Purpose When the video quality is diagnosed abnormal e g blurred image abnormal brightness and color cast the alarm will be triggered and linked with the configured response actions Steps 1 Enter the Video Quality Diagnostics interface Menu Camera Video Quality Diagnostics 2 Select the camera for adjusting the video quality parameters Check the checkbox to enable the Video Quality Diagnostics 4 Click the to enter the Settings interface Configure the arming schedule of triggering video quality diagnostics alarm Settings Linkage Action Mion 10 00 16 00 00 00 00 00 00 00
169. word of the admin user account can be changed in the User Management menu Steps 1 Enter the User Management interface Menu Configuration User test Guest 00 00 00 00 00 00 test02 Operator 00 00 00 00 00 00 Figure 13 12 Change Password 2 Select the admin user and click LA to change the password 208 User Manual of DS 7200 7300 8100 Series DVR Edit User 00 00 00 00 00 00 Cancel Figure 13 13 Change Password 3 Enter the old password check w checkbox enter new password and confirm password on the menu 4 Click OK to save the settings and exit the menu 209 User Manual of DS 7200 7300 8100 Series DVR Chapter 14 Appendix 210 User Manual of DS 7200 7300 8100 Series DVR List of Compatible Hikvision IP Cameras Max Model Version Sub stream Resolution 893PF E 704x576 893PFWD E DS 2CD7153 E V5 0 8 build130930 1280x720 DS 2CD8153 E 1280x720 DS 2CD8254F EIS 1920x1080 y DS 2CD864FWD E 1280x720 DS 2CD8264FWD EIS HD Network DS 2CD2012 I Camera DS 2CD2112 I DS 2CD2212 I V5 0 5build131017 1280x720 DS 2CD2312 I DS 2CD2612F I DS 2CD2712F I DS 2DF7274 V5 1 0 build 130923 1280x960 Network Speed DS 2DF5274 Dome DS 2DE7174 V5 0 2Build130926 1280x960 DS 2DE5274 S For the list our company holds right to interpret 4 4 4 211 User Manual of DS 7200 7300 8100 Series DVR Glossary e Dual Stream Dual stream is a technology used to record high resolutio
170. y HDVR series only 3 Click the Apply button and the following Attention box will pop up Attention Reboot to take effect of the changing of the storage mode Continue Yes No Figure 10 10 Attention for Reboot 4 Click the Yes button to reboot the device to activate the changes 5 After reboot of device enter the HDD Information interface 177 User Manual of DS 7200 7300 8100 Series DVR Menu HDD General 6 Select HDD from the list and click the LA icon to enter the Local HDD Settings interface Local HDD Settings HDD Property O RW Read only Redundancy Group SEC INE CEE ROM LES EEE E EEE DLE DIE RPM REM ECE EDE RIO 931GB Cancel Figure 10 11 Local HDD Settings Interface 7 Select the Group number for the current HDD NOTE The default group No for each HDD is 1 8 Click the OK button to confirm the settings Attention Regroup the cameras for HDD if the HDD group number is changed Yes NO Figure 10 12 Confirm HDD Group Settings 9 Inthe pop up Attention box click the Yes button to finish the settings 10 3 2 Setting HDD Property Purpose The HDD property can be set to redundancy read only or read write R W Before setting the HDD property please set the storage mode to Group refer to step1 4 of Chapter 10 3 1 Setting HDD Groups A HDD can be set to read only to prevent important recorded files from being overwritten when the HDD becomes full in overwrite r
171. y local video output and menu 9 eSATA Connects external SATA HDD DVD R W RS 485 termination switch Up position is not terminated Termination Switch l l l Down is terminated with 120Q resistance RS 485 Interface Connector for RS 485 devices Connect the T and T terminals to the R and R terminals of PTZ receiver respectively KB Connect the D and D terminals to Ta and Tb terminals of the controller For cascading devices the first DVR s D and D terminals should be connected with the D and D terminals of the next DVR Alarm In Out Connector for alarm input output 100 240VAC 100 240VAC power supply POWER Switch for turning on off the device Ground needs to be connected when DVR starts up The rear panel of DS 8132 DVR is shown in Figure 1 12 099909999999999 o o4 0909090909090909090909990 p OROLOROROR OnO ORF OL OL OR OPO 050999999999999999989999999 3 4 5 7 89 10 11 121314 15 16 Figure 1 12 Rear Panel of DS 8132 ES NOTE DS 8124 provides 24 video input interfaces on the rear panel Table 1 12 Description of Rear Panel BNC connector for video output BNC connector for spot video output RCA connector for audio output This connector is synchronized with CVBS AUDIO OUT l E CVBS video output 26 RCA connector for audio output This connector is synchronized with VGA VGA AUDIO OUT l video output User Manual of DS 7200 7300 8100 Series DVR 9 HDMI HDMI v
172. ype Edit Date Delete Play a01_md_ch01_ 130 2 626KB File 07 22 2013 14 04 17 m e a LLL gt 7 660MB New Folder Format Cancel Figure 7 12 Checkup of Event Export Result Using USB Flash Drive 7 1 4 Backing up Video Clips Purpose You may also select video clips to export directly during Playback using USB devices USB flash drives USB HDDs USB writer SATA writer or eSATA HDD 124 User Manual of DS 7200 7300 8100 Series DVR NOTE The eSATA writer is supported by DS 7300 and DS 8100 models only Steps 1 Enter Playback interface Please refer to Chapter 6 2 During playback use buttons dy and in the playback toolbar to start or stop clipping record file s gt Normal x Max Ca Min Ca iv M Camera 02 Camera 03 M Camera 04 M Camera 05 Camera 06 Camera 07 Camera 08 lllCamera 01 llliPCamera 02 SMTWTFS d 2 3 asho 01 01 2013 00 00 24 12 19 2013 15 51 28 Figure 7 13 Interface of Playback by Time 3 Click the icon s to enter the Clips Export interface NOTE A maximum of 30 clips can be selected for each channel 4 Click the button Export to export the selected video clips to the backup device Refresh Size Type Edit Date Delete Play 7 664MB New Folder Format Figure 7 14 Export Video Clips Using USB Flash Drive 125 User Manual of DS 7200 7300 8100 Series DVR Stay in the Exporting interface until all record files are exported with pop up message
173. ype to HDD Error from the dropdown list 3 Click the checkbox s below to select the HDD error alarm type s Nore The alarm type can be selected to Audio Warning Notify Surveillance Center and Send Email Please refer to Chapter 8 5 Setting Alarm Response Actions HDD Error Figure 10 22 Configure HDD Error Alarm 4 Click the Apply button to save the settings 184 User Manual of DS 7200 7300 8100 Series DVR Chapter 11 Camera Settings 185 User Manual of DS 7200 7300 8100 Series DVR 11 1 Configuring OSD Settings Purpose You can configure the OSD On screen Display settings for the camera including date time camera name etc Steps 1 Enter the OSD Configuration interface Menu gt Camera gt OSD Select the camera to configure OSD settings Edit the Camera Name in the text field Configure the Display Name Display Date and Display Week by clicking the checkbox oS ae cu 9 Select the Date Format Time Format and Display Mode Analog 1 Camera 01 05 09 2012 Wed 13 50 45 i2 isplay Date v MM DD YYYY iat 24 hour lay Mode Transparent amp Not Flashing Camera 01 w 2 Figure 11 1 OSD Configuration Interface 6 You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position 7 Copy Camera Settings 1 If you want to copy the OSD settings of the current camera to other cameras click the Copy button to enter the Copy C

Digital Video Recorder User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents