Home

Manual

1. Current mains 0 65A at full charging current e Never charge a battery with temperature below 0 C if not specified by the ang battery manufacturer Back current drain lt 1Ah month Never place the charger on top of the battery when charging Ripple lt 4 Always provide for proper ventilation during charging TIET F 3 A Avoid covering the charger Ambient 20 C to OAC output power is reduced All batteries fail sooner or later A battery that fails during charging is normally taken temperature cutomaticall ycuhighitempensiuies care of by the chargers advanced control but some rare errors in the battery could Charger type 8 step fully automatic charging cycle 0 exist Don t leave any battery during charging unattended for a longer period of Battery types 12V LiFePO batteries ime Ensure that the cabling does not jam or comes into contact with hot surfaces or sharp Battery capacity 5 60Ah up to 120Ah for maintenance edges Dimensions 168 x 65 x 40mm Lx W x H Always check that the charger has switched to STEP 7 before leaving the charger unattended and connected for long periods If the charger has not switched to STEP 7 Insulation class IP65 within 24 hours this is an indication of an error Manually disconnect the charger Weight 0 6kg e This appliance is not designed for use by young children or people who cannot read or understand the manual unless they are under the supervision of a responsible Back current dra
2. been opened and the battery is ready to be charged the charger automatically starts the charging cycle CTEK COMFORT CONNECT clamp EN 3 20018043A LITHIUM XS EU Manual Print file_004 indd 3 2013 03 04 14 34 41 The battery is ready to start the engine when STEP 3 is lit z ERROR LAMP If the error lamp is lit check the following 1 Is the chargers positive lead connected to the battery s positive pole 2 Is the charger connected to a 12V LiFePOs battery 3 Has charging been interrupted in STEP 1 or 4 Restart the charger by pressing the RESET button If charging is still being interrupted the battery STEP 1 can not accept charge may be too large for the charger to wake up Press RESET button up to 5 times a paralell load may be connected to the battery Disconnect the battery and try again STEP 4 can not keep charge and may need to be replaced POWER LAMP If the power lamp is lit with a 1 STEADY LIGHT The mains cable is connected to the wall socket 2 FLASHING LIGHT The charger has entered the energy save mode This happens if the charger isn t connected to the battery within 2 minutes or the battery on board UVP under voltage protection is activated READY TO USE The table shows the estimated time for an empty battery to reach 90 state of charge SOC Please note that charging times are longer in low ambient temperatures BATTERY SIZE Ah TIME TO 90
3. 6 SE525604 D596125 RCD 001705138 0001 US D29 378528 pending ZL 201030618223 7 US RE42303 US RE42230 EN 7 20018043A LITHIUM XS EU Manual Print file_004 indd 7 2013 03 04 14 34 42 8 EN 20018043A LITHIUM XS EU Manual Print file_004 indd 8 2013 03 04 14 34 42
4. CHARGED 8Ah 2h 20Ah 5h 60Ah 16h 4 EN 20018043A LITHIUM XS EU Manual Print file_004 indd 4 CONNECT AND DISCONNECT THE CHARGER TO A BATTERY INFO If the battery clamps are incorrectly connected the reverse polarity pro tection will ensure that the battery and charger are not damaged For batteries mounted inside a vehicle 1 Connect the red clamp to the bat tery s positive pole 2 Connect the black clamp to the vehicle chassis remote from the fuel pipe and the battery 3 Connect the charger to the wall socket 4 Disconnect the charger from the wall socket before disconnecting the battery 5 Disconnect the black clamp before the red clamp Some vehicles may have posi tively earthed batteries Connect the black clamp to the bat tery s negative pole 2 Connect the red clamp to the vehicle chassis remote from the fuel pipe and the battery 3 Connect the charger to the wall socket 4 Disconnect the charger from the wall socket before disconnecting the battery 5 Disconnect the red clamp before the black clamp Comfort Connect 2 2013 03 04 12 CHARGING PROGRAM ACCEPT BULK ABSORPTION ANALYSE COMPLETION MAXIMIZATION FLOAT PULSE VOLTAGE V Gore eres Pera Increasing voltage to 13 8V 5A CURRENT A Charge cycle restarts if voltage drops Max 10h 3minutes Charge cycle restarts if voltage drops STEP 1 ACCEPT STEP 5 COMPLET
5. CONGRATULATIONS HOW TO CHARGE To the purchase of your new professional switch mode battery charger This charger is 1 Connect the charger to the battery included in a series of professional chargers from CTEK SWEDEN AB and represents the latest technology in battery charging The LITHIUM XS charger model is designed for Lithium ion batteries using LiFePO technology only Please check with the battery manufac turer for details Do not use the LITHIUM XS charger for any other battery technology 2 Connect the charger to the wall socket 3 Follow the 8 step display through the charging process The battery is fully charged when STEP 7 is lit 4 Stop charging at any time by disconnecting the mains cable from the wall socket SUPPLY PLUG MAINS CABLE CTEK COMFORT CONNECT READY TO USE FULLY CHARGED RESET BUTTON ERROR LAMP CHARGE CABLE POWER LAMP CTEK COMFORT CONNECT eyelet M6 BATTERIES WITH UNDER VOLTAGE PROTECTION Some Lithium ion batteries have an on board UVP under voltage protection that disconnects the battery to avoid it becoming too deeply discharged This prohibits the CTEK charger from detecting that there s a battery connected To bypass this the bat tery charger needs to open the UVP By pressing the RESET button for 10 seconds the Supply plugs may differ to suit your wall socket charger opens the UVP During this process the charging STEP 7 is lit Once the UVP has
6. ION Tests if the battery can accept charge This step prevents that charging proceeds with a Final charge with reduced current defect battery STEP 6 MAXIMIZATION STEP 2 BULK Final charge with maximum voltage up to 100 battery capacity Charging with maximum current until approximately 90 battery capacity STEP 7 FLOAT STEP 3 ABSORPTION Maintaining the battery voltage at maximum level by providing a constant voltage charge Charging with declining current to maximize up to 95 battery capacity STEP 8 PULSE STEP 4 ANALYSE Maintaining the battery at 95 100 capacity The charger monitors the battery voltage Tests if the battery can hold charge Batteries that can not hold charge may need to be and gives a pulse when necessary to keep the battery fully charged replaced EN 5 20018043A LITHIUM XS EU Manual Print file_004 indd 5 2013 03 04 14 34 42 SAFETY TECHNICAL SPECIFICATIONS e The charger is designed for charging 12V Lithium ion batteries with LiFePO4 technol ogy Do not use the charger for any other purpose Model number 1081 e Never try to charge non rechargeable batteries Rated Voltage AC 220 240VAC 50 60Hz Check the charger cables prior to use Ensure that no cracks have occurred in the Charging voltage 13 8 14 4 VDC cables or in the bend protection A charger with damaged cables must not be used ging 9 A damage cable must be replaced by a CTEK representative Charging current 5A max Never charge a damaged battery
7. in is the current that drains the battery if the charger is not connected to person to ensure that they can use the battery charger safely Store and use the bat the mains CTEK chargers have a very low back current i tery charger out of the reach of children and ensure that children cannot play with the The quality of the charging voltage and charging current is very important A high cur charger rent ripple heats up the battery which has an aging effect on the positive electrode High voltage ripple could harm other equipment that is connected to the battery CTEK battery chargers produce very clean voltage and current with low ripple The battery charger is designed to operate from 20 C to 50 C However battery manufacturers may recommend other temperature ranges for charging their batteries Please check battery specifications Connection to the mains supply must be in accordance with the national regulations for electrical installations 20018043A 6 EN 20018043A LITHIUM XS EU Manual Print 116 004 indd 6 2013 03 04 14 34 42 LIMITED WARRANTY CTEK PRODUCTS ARE PROTECTED BY 2012 05 30 CTEK SWEDEN AB issues this limited warranty to the original purchaser of this product Patents Designs Trademarks This limited warranty is not transferable The warranty applies to manufacturing faults EP10156636 2 pending RCD 509617 TMA 669987 and material defects for 5 years from the date of purchase The customer must ret
8. urn the US12 780968 pending US D575225 CTM 844303 product together with the receipt of purchase to the point of purchase This warranty is EP1618643 US D580853 CTM 372715 void if the battery charger has been opened handled carelessly or repaired by anyone US7541778 US D581356 CTM 3151800 other than CTEK SWEDEN AB or its authorised representatives One of the screw holes EP1744432 US D571179 TMA 823341 in the bottom of the charger is sealed Removing or damaging the seal will void the war EP1483817 pending RCD 321216 CTM 1025831 ranty CTEK SWEDEN AB makes no warranty other than this limited warranty and is not SE524203 RCD 000911839 CTM 405811 5 liable for any other costs other than those mentioned above i e no consequential dam US7005832B2 RCD 081418 CTM 830545751 pending ages Moreover CTEK SWEDEN AB is not obligated to any other warranty other than this EP1716626 pending RCD 001119911 0001 CTM 1935061 pending warranty SE526631 RCD 00111991 1 0002 V285731P00 US7638974B2 RCD 081244 CTM 2010004118 pending SUPPORT EPO9180286 8 pending RCD 321198 CTM 4 2010 500516 CTEK offers a professional custom support www ctek com 0 pending RCD 321197 CTM 410713 For latest user manual see www ctek com By e mail info ctek se a ne s pending by telephone 46 0 225 351 80 by fax 46 0 225 351 95 US7629774B2 RCD 001505138 0001 CTM 766840 pending EP09170640 8 pending RCD 000835541 0001 US12 564360 pending RCD 00083554 02 E528232 D59612

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents