User Manual - ACE PLUS CORP.
Contents
1. Power on the KVM again 6 You can use the system setting F1 Information in the OSD to examine whether or not the F W version is the updated version 14 TROUBLESHOOTING Confirm whether or not the cable is good and connected properly Ol What should we do if the keyboard has no response Ala Reboot the PC Alb For Auto Scan Mode press Esc to exit Q2 What should we do if the mouse has no respond A2a Reboot the PC A2b For Auto Scan Mode press Esc to exit Q3 What should we do if the OSD cannot display normally A3a Ifthe KVM switch is a standalone then power off the PC Unplug the special cable of the KVM switch and then power on the KVM switch Connect the special cable of the KVM switch and power on the PC A3b Ifthe KVM switch is connected in series then power off the PC Unplug the special cable of the KVM switch Power on the master KVM switch and then start the slave KVM switch Connect the special cable to the KVM switch and power on the PC Q4 What should we do if there is a video problem A4 The quality of cable is not good enough Please use high quality Smart View cables Trademarks All the companies brand names and product names referred to this manual are the trademarks or registered trademarks belonging to their respective companies 152. method for the switch OSD On Screen Display Press the NumLock on the keyboard twice or simultaneously press the Push Buttons and 2 of the Port Selection Switch on the KVM panel to start the OSD Use the Up Down and Enter keys on the keyboard to switch or directly move the mouse to the target PC and then double click the left button Additionally you also can use the numeric keys to enter the direct switch For example if you want to switch a PC to the Slave KVM port 04 under the Master KVM port 03 then you can start the OSD and then directly enter 0304 If you are using a standalone machine then just enter the first two digits More OSD related information are given in the following OSD sections On Screen Display OSD Start Press the NumLock twice or the Port Selection Switches 1 and 2 on the panel to enter the OSD Note If you have modified the Hot Key for starting the OSD and are unable to enter the OSD by pressing NumLock then you can start the OSD by using the Port Selection Switch first and then press F9 to enter into the System Setting to modify the options of the OSD Entry Hot Key Operation You can operate the options by keyboard or mouse For the keyboard operation besides the common Up and Down keys there are special function keys such as Enter Space Bar Function Key F1 F4 under the OSD remark field For the mouse operation the left key refers to Enter and the right key refers to Exit For example move
3. What should I do if I forgot my Password After you enter a wrong password for 5 consecutive times a time delay bar will appear and a set of Magic Numbers will show up at the bottom Record the magic numbers and contact with your distributor e EDID amp DDC A vast majority of computer monitors supports the Extended Display Identification Data EDID and allows data access by Display Data Channel DDC The KVM also supports these two specifications but the KVM only reads the EDID of the Monitor when the KVM is on If it is necessary to change monitors during an operation please use the Console Reconfirmed function to read the EDID again e F W Update This product provides a firmware update function You can contact your distributor for downloading application programs and updated files Use the F W Update Cable for the update Please turn off all PCs before carrying out the update and do not disconnect the power during the update process Procedure 1 Download and install the application program KVMISP msi Note This program has to be run only in Win98SE ME XP or 2000 2 Connect the F W Update Cable and the PC end is RS 232 port COM X while the KVM end is the updata port 3 Power on the KVM and run KVM ISP exe Select the COM port 4 Select the Download function and specify to update the KVM XXXX KVM file 5 After the update completes which takes about 1 5 min power off the KVM Unplug the F W Update Cable
4. the mouse point to your desired PC and click the left key The selection bar will move to that position and then click the left key again for the execution Note You must use the keyboard to complete the two functions Name Edit and Password 10 e Switch Menu Master List ls E LIST MASTER PWR C KVM NAME SVS Admin Man Game Press Enter gt Peter Web Group Data Group 0 27 Move Space Edit Esc Exit F1 Smart View Enter Switching F4 Auto Scan F9 System Setting F5 Clear Name List Slave List Mal Ser Mal Ser 2 Mail Ser 3 Mail Ser 4 0 6227 Move Space Edit Esc Exit F1 Smart View Enter Switching F4 Auto Scan F9 System Setting F5 Clear Name List 1 This field provides the information of the currently connected PC As shown in the figure above 03 refers to the Port Number of the Master 04 refers the Port Number of the Slave and Mail Ser 4 is the name of this PC defined by Users If a PC connects to the Master then the number consists of the first two digits If a User has not given a name for the PC the name field will be blank 2 This field shows the list of the Master KVM or a certain set of Slave KVM currently displayed on the OSD We recommend you to give a name to the Slave KVM or else the display after LIST will be blank 3 This field shows the list of connections to the KVM and the fields are described below 11 PWR It shows the status of power supply and indicates a no
5. 504 Front View as O amp IC 1508 Front View eg O amp IC 1516 Front View OLO 1 Port Selection Switches Press the push button to directly switch to the corresponding PC e In the cascade architecture if the port is connected to KVM but not PC then the push button will not respond e Simultaneously press Push Buttons 1 and 2 to directly enter the OSD Control Mode e Simultaneously press Push Buttons 3 and 4 IC 1504 Push Buttons 7 and 8 IC 1508 Push Buttons 15 and 16 IC 1516 to open Console Reconfirmed and the keyboard and mouse will be reconnected and the EDID in the screen will be read again 2 Port LEDs These Port LEDs are built in the Port Selection Switches Online A green light indicates that the PC or KVM connected to the corresponding port is on and operating Selected A red light indicates the situation of being connected to the port e Ifa port is connected to KVM then the red light of that port will not on e Besides the special mode the whole system architecture only has one red light indicating that the Console is connecting to the PC or has no red light when powering on the KVM for the first time 3 Power LED An blue light indicates that the KVM is operating 6 1C 1504 Rear VIEW O IC 1508 Rear VIEW IC 1516 Rear VIEW Tr CA OOD 1 CPU Port Install the cable connected to a PC here 2 Updata Port The port prov
6. LCD KVM SWITCH Cyber Console IC 1504 IC 1508 IC 1516 USER MANUAL LCD MONITOR SPECIFICATIONS OPERATION Keypad Define Power key Use this key to turn on or off the LCD monitor Menu key Use this key to open the OSD menu or return to a previous menu or exit the OSD menu Up key Use this key to highlight an item in the menu move a highlighted function up or increase the numeric value parameter in certain menu Down key Use this key to highlight an item in the menu move a highlighted function down or decrease the numeric value parameter in certain menu Enter key Use this key to enter next menu or highlight a confirmed function If the screen is not in a full screen graphic mode such as in a DOS or is connected with an allocator the position of the appeared image may be adjusted automatically and then deviated By then it is necessary to enter into the OSD menu to manually adjust the level or vertical position and phase OSD Control Function List Contrast Brightness Display Adjust V Position H Position Phase Clock Auto Adjust Returm Color Control 9300K 6500K User Auto Color Returm Language English Deutsch Frangais Italiano Espafiol Chinese Returm OSD Adjust OSD V Position OSD H Position OSD Timeout Returm Audio Control Mute Volume Returm Reset Exit CONINDAKRWN EH BRIEF INTRODUCTION The KVM Switch allows you to control several sets of personal c
7. actory default settings Please note that all name lists will be cleared and the system settings are set to the default settings as shown in the table above Esc Exit Exit the system setting and close the OSD If you have made changes in this option the system will ask whether or not you want to save the setting before the selected option is effective e Auto Scan Mode You can start the OSD first and press F to enter the Auto Scan Mode If you want to scan the PC you must use the Smart View Setting to select the Auto Scan Time in the System Setting for the residing time which includes 5 sec 10 sec 20 sec 30 sec and 60 sec You can adjust the Channel Display Mode and Channel Display Time from the Channel Display mode By then all keys on the panel keyboard and mouse are not operable You can only use the ESC key to exit the Auto Scan Mode e Security Mode Switch the Security Level from None to Low in the System Setting and enter your Password A Z 0 9 a maximum of 12 characters and the security will be effective after you confirm the Password The use of the Console Lock Time is to set the time to enter a security mode after the keyboard and mouse has idled for a predetermined time Once you enter into the security mode you need to enter the correct password before you can move the mouse or enter any key from the keyboard You need a correct password to operate the whole system normally Important Note
8. ar panel of the KVM is OFF Use the AC power cord 3 in 1 cable to connect the console port of the slave KVM to the CPU port of the master KVM Power on the slave KVM For example If you want to install one Slave KVM and three PCs then just follow Step 2 of the foregoing method to add the slave KVM and install the PCs one by one according to Step 1 OPERATION Port Selection The LCD KVM provides fours switching methods Manual Key Hot Key Mouse Clicking and OSD e Manual Key It is the simplest switching method You just need to press the Port Selection Switch on the front panel of the KVM The Selection LED Red is on indicating that you are switching to the corresponding port Note 1 The Port Selection Switch functions only when connected to a PC 9 2 If the Offline Skip of the OSD System Setting is Auto then you cannot make any switch when pressing an offline Port Selection Switch 3 For Auto Scan Mode none of the Port Selection Switches functions Hot Key and Mouse Clicking Hot key and mouse clicking are applicable for switching a small section You can select the SVS Smart View Setting from the OSD of the PC first for a quick switch of PC and use the keyboard press the Ctrl key twice or the mouse press and hold the middle button while pressing the left or right button to switch to the previous or next set of PC Note The mouse must have at least 3 keys As far as you select a PC with the SVS you can use this
9. ides a firmware update function 3 AC Power Jack The AC Power is applicable for 100 240V AC 50Hz 60Hz 4 Power Switch Power On Off the LCD KVM INSTALLATION e Standalone 1 Make sure that the power switch at the rear panel of the KVM is OFF Plug an end of the AC power cord into the KVM and the other end to an AC power supply 2 Make sure to power off the PC and then install the 3 in 1 cable to each of the PC one by one Note If the ON LINE LED Green of any port of a PC is on then we recommend you to power off such PC Turn off the power switch of the power supply of the PC or unplug the power cable of the PC or wait till Step 5 to install that particular PC 3 Turn on the power switch at the rear panel of the KVM 4 Power on the PC Note It is not necessary to power down the whole system for install a new PC or KVM thereafter All you need is to make sure that the new PC or KVM is OFF during the installation If the KVM powers down due to external factors such as power failure or the power of the KVM is turned off we recommend you to reinstall the whole system e Connection in Series 1 Make sure that the power switch at the rear panel of the Master KVM is OFF Plug one end of the AC power cord to the KVM and the other end to the AC power supply 2 Make sure the power switches at the rear panels of all slave KVMs are OFF Plug one end of the AC power cord to the KVM and the other end to the AC power supply 3 Ins
10. l information Full Ki ame and mode selection A A It shows the time for displaying channel 10Sec Always Channel Display Time f 5 Sec information None i For Auto Scan it shows the residing time for each 10Sec 20Sec Auto Scan Time 5 Sec port 30Sec 60Sec Select to turn on the hot keys of the OSD control screen Turn on off the Ctrl hot keys on the keyboard OSD Entry Hot Key Hot Key Switchin 4 F for switching computer functions yaly Turn on off the keys of the mouse for switching OFF ON computer functions Beeper Sound Turn on off the beeper sound function Offline Skip Set the offline skip function to auto or manual i Frangais Deutsch OSD Language Select the language for the OSD English i 7 Italiano Espa ol Security Level Select the security mode and level Console Lock Time 1Min 3Min 10Min The lock time of console port i i 30Min 60Min 1 You can select this option only if the Security Level is not None F1 Information It provides the model name and F W version information which is helpful for users to understand the updated version F4 OSD Position You can enter the OSD position to make adjustments we recommend you to unify the resolution for all computer display mode and use this function again to adjust the OSD position You can use the Up Down Left or Right keys on the keyboard or a mouse to move 13 the OSD position F8 Restore Default Setting Restore the f
11. of PCs Through OSD you can use the hot key mouse clicking and push button on front panel to switch PCs Monitors PC status by Auto Scan function Supports resolution of 1024x768 75Hz and independently supports EDID amp DDC2 of each PC Each Port on the panel of the KVM has independent push buttons and LED lamps for easy switch and identification Complies with the height of the 1U chassis specification and installable with a hanging stand into a 19 chassis system Requires no additional software or hardware Supports hot plug not necessary to turn off the original system regardless of a newly installed PC or KVM UIPMENT REQUIREMENTS Computer System e A Supported VGA SVGA XGA SXGA or Multisync Video Card e A PS 2 mini DIN 6Pin Mouse port e A PS 2 mini DIN 6Pin or AT 5 Pin DIN with AT to PS 2 Adaptor Keyboard port Cable e 3 in 1 KVM Cable please contact your local distributor for detailed specification and length Connected to CPU port of KVM Connected to Console port of PC or Slave KVM TE ee EES i AAA mnn gt NI m f j 11 MW Eka mr Jom lt A ESE II con mi t Hi e f i M SPECIFICATIONS po 1 1504 1C 1508 1C 1516 CPU 3 in 1 16 Connecter HD 15 Female 15 TETLCD Console Touch pad module Connector Keyboard Standard 104 key Port Selection Keys on 4 ja 8 e T EHIS 23K 20 60 C 16 16 1 OSD 10 80 RH non condensing CONFIGURATION IC 1
12. omputers by a keyboard a mouse and a monitor In the meantime you just need to connect the cable and turn on the power to control up to 256 sets of personal computers without installing any additional interface card or software Easy Installation The 3 in 1 CPU Connector VGA Keyboard and Mouse can save the installation time and space and assure the correct signals The universal AC power input of 100 240VAC 50Hz 60Hz saves you the trouble of finding the space for installing the Power Adaptor You can install a cascade to facilitate expansions or transportation without requiring a cascade cable or changing the KVM configurations On Screen Display OSD Menu The embedded OSD control module lets you name the PC and KVM and modify the KVM configuration and the security mode can prevent others from turning on the KVM by mistake and switching the linked PC from the OSD Most conveniently the OSD not only supports keyboard operations but also supports mouse clicking Enhanced Video Quality The special video circuit design supports resolution up to 1024x768 75Hz and also keeps the same quality under the Cascade architecture PACKAGE INSIDE KVM Switch x1 USER Manual xl Power Cord xl F W Update Cable x1 Rack Mount Brackets x2 Screws for Brackets x6 Key x 2 FEATURES E The keyboard mouse and 15 LCD monitor was built in on KVM switch Standalone machine controls up to 4 8 16 sets of PCs Cascade controls 64 128 256 sets
13. rmal power supply for the eguipment PC or KVM connected to the CPU port C It shows the channel number the IC 1504 will display 01 04 the IC 1508 will display 01 08 and the IC 1516 will display 01 08 09 16 Since the screen cannot display all at a time therefore you can use PgUp PeDn to switch the pages KVM It shows the KVM model If there is a number in this field it shows that a set of KVM connects to this port The number 04 indicates Port 4 and 08 indicates Port 8 and 16 indicates Port 16 and so on Note If the connected KVM is not on there will have no number in this field NAME It shows the name of the eguipment and users can name the Slave KVM or PC on their own There are a total of 12 characters selected from the group of A Z 42 310 90 11 gt 1 21 A 210 2210 2 2 03 ace Note Please use the CapsLock to toggle the upper and lower cases SVS It shows the Smart View Setting use 9 to open and to close The SVS is blank and not clickable if the KVM is connected in parallel If this option is set to open then you can make the switch by operating the Hot Key Switch or Mouse Clicking or selecting the option by Auto Scan You also can use mouse to click this field Selection BAR It shows the selection bar Green you can use the keys on the board to move the selection bar and the situated position indicates the selected target for giving instructions For example if the selection bar points at C 05 and
14. tall the Master KVM to the 3 in 1 cable same as the cable for connecting the KVM to the PC in the middle of the Slave KVMs 4 Make sure the power of the PC is OFF and then install the 3 in 1 cable to each PC one by one Note Install the PCs on the master or the PCs on the Slave first If the ON LINE LED Green of any port of a PC is on then we recommend you to power off such PC Turn off the power switch of the power supply of the PC or unplug the power cable of the PC or wait till Step 8 to install that particular PC 5 Turn on the power switch at the rear panel of the master KVM 6 Turn on the power switch at the rear panel of the slaver KVM 7 Power on the PC Note It is not necessary to power down the whole system for install a new PC or KVM thereafter All you need is to make sure that the new PC or KVM is OFF during the installation If the KVM powers down due to external factors such as power failure or the power of the KVM is turned off we recommend you to reinstall the whole system 8 Note It is noteworthy that there are two levels available ojo Ka Ku Ku Ku of Ka off Je Je Jo Jo Jo of Jo Jo ofc of gt e Expansion 10 PCs It is not necessary to power down the KVM or other computer connected to the KVM system You only need to power off the desired PC and connect the PC to the CPU port of the KVM in parallel by the 3 in 1 cable and then power on the PC 20 Slave KVM Make sure the power switch at the re
15. you press Enter then the system will switch to that particular PC or press the Space BAR to start editing the name Press F4 to enable disable the SVS option 4 Instruction Hint Field d 22 Move Use the 2 keys on the keyboard or the mouse to move the selection bar SPACE Edit The Space BAR on the keyboard is used to start editing the name of the PC or KVM ESC Exit Use the Esc key on the keyboard to exit the current option or exit OSD F4 Auto Scan Use the F4 key to run Auto Scan and you can set the residing time channel display time and mode of the Auto Scan from System Setting F9 System Setting Use the F9 key to enter into the System Setting Menu F5 Clear Name List Use the F5 key to clear the values of all Name fields If you clear the name list under the Master screen then you will also clear the name lists under all slaves If you clear the name list under a certain slave then you only clear the name list under that particular Slave KVM F1 Smart View It switches the Smart View Setting 12 e System Setting Menu Channel Display Mode Channel Display Time Auto Scan Time OSD Entry Hot Key Hot Key Switching Mouse Clicking Security Level Console Lock Time Space Change Esc Exit F1 Information F4 OSD Position F8 Restore Default Setting Default Other Selection For Port Switching Auto Scan and OSD Close Numb umber Channel Display Mode the Monitor will show the Channe
Download Pdf Manuals
Related Search