30-01 Keypad
Contents
1. Enter the Master Code and wait for the red LED to come on Enter the Master Code for a second time and wait for the green LED to come on Enter the code 66 and the green LED should be lit Press any two keys from 01 to 99 for the new time delay 01 being 1 second and 99 being 99 seconds The green LED will then flash in standby To Change the Duration of Door Latched Mode Enter the master code and wait for the red LED to light Enter the master code for the second time and wait for the green LED to light Press keys 71 and the green LED will light Press any two keys from 01 to 99 for the new time delay in minutes 01 being 1 minute and 99 being 99 minutes The green LED will then flash in standby 7 To Change the Duration of Door Unlocked Mode Enter the master code and wait for the red LED to light Enter the master code for the second time and wait for the green LED to light Press keys 77 and the green LED will light Press any two keys from 01 to 99 for the new time delay in seconds 01 being 1 second and 99 being 99 seconds The green LED will then flash in standby To Delete all User Codes from Positions 01 to 50 Enter the master code and wait for the red LED to light Enter the master code for the second time and wait for the green LED to light Press keys 88 and the red LED will light for approximately 3 seconds The green LED will then flash in standby To Change the Duration the Exit B2. of the back plate Tighten the Allen screw and complete the remaining tasks as described Fig 3 Inserting Keypad Cable into Back Plate Fig 4 Fitting Keypad to Back Plate Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 paddas AOW ul YUM pany aq osjo snus joo a41 SION uowwop Anjey 1ooq O4 Jur At soq NSd DA AZL 1NDAG IDJ PUD JDo DJ yoq 104 32o wouy jddng aayoBey 94 Ip uuoO aauDBan NSd DA AZL n 1 JDS IDJ 4 AJU 4907 uuoj jddng BAYISOd Ip uuoO O N oj y 4207 POWER AC DC 11 16V 10 12443 Y z WM S GO 1no IDJ 4 AU 32o1 Woy jddng AIIISOq I9 uuoO C N Adjay 4207 Naniaa BAUISOd Sd OF UN uowwos Adjey 4207 q LIXd 2 3OOq WM YO Y se ole e pesn JON Jod uong 4x9 gt s 1b p QZ 0Z 1nipi dui 9019 Bpl oA Buyosedo y yo sduip g Buyos wnwxow Anjay 100q 32o 100p Buipn oui jou owog moig wnwixoy pw xoiddo pow qpupis uoydwnsuop Iu iuino Dd 10 DV SHOA BL OF ZL BoljoA Buipisdo uollp3lji5 d s UMOUS OGAZT TO O Aeyery 104 wesselq SUMIM Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 User Manual for RiteKey 30 01 02 Glossary of Terms Master Code The code used for programming the user codes and any changes to the default settings of the keypad User Code The access code given to an individual us
3. EUROPE LIMITED Fitting Instructions Py ADAMS RITE RiteKey 30 01 IP65 Rating Keypad Face Only Contents Installing Keypad and Backplate Wiring Details User Manual Adams Rite Europe Ltd Moreton Industrial Estate London Road Swanley Kent UK BR8 8TZ Tel 44 0 1322 668024 Fax 44 0 1322 660996 E mail info adamsrite co uk www adamsrite co uk Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 Installing Keypad and Backplate Fig 1 Positioning of Fixing Holes and Cable Outlet Cable Outlet Drill Diameter 10mm for Cable Access Remove the back plate which is fitted to rear of the keypad using a 2mm Allen key provided and put the screw in a safe place Fixing Holes Fig 2 Preparation and Installation of Back Plate Select a suitable location to fit the keypad and mark the position to two fixing screws and the cable access hole as per fig 1 If fitting to brickwork use the rawl plugs provided and drill two 6mm diameter holes to suit Otherwise drill the two fixing holes 3mm in diameter to allow a 4mm button head screw to cut its own thread Install the cable run to the power supply and the lock Ensure the diameter of the cable is sufficient for the length of the run and the amperage draw of the lock so as to minimise line drop Alarm cable or bell wire is not recommended for access control installations Ensure the MOV supplied is fitted to the lock either to its supply c
4. ables or on its supply connections on its terminal block Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 Terminal block shown in position as shipped note its position with the cable entry pointing away from the PCB The wall of the keypad is particularly removed for clarity 8 3 8 aL femme mnnn nan P Fig 3 Position of Terminal Block Fig 4 Diagram Showing PCB Connections Remove the terminal block from the PCB which separates from the terminal pins by pulling on the terminal block As the terminal block is lifted away it will reveal the functions of the different pins written onto the PCB as shown in fig 4 Make the connections to the terminal block as per the diagram and refit the terminal block to the PCB Please take care to refit Fig 5 Connecting the Cable Run and Block to the Keypad the block the correct way around with the cable entry pointing away from the PCB as shown in diagram 3 Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 6 Once the back plate has been securely fastened to the application and the terminal block has been correctly installed on the keypad PCB the keypad is ready to install onto the back plate Hook the keypad onto the back plate by the slot in the rear of the keypad located at the top of the aperture as per fig 4 Pivot the keypad so that it sits flat against the back plate and is in line with the tapped hole located in the underside of the flange
5. er that will allow entry to the building but does not allow the user to change any of the codes or default settings Duration of Door Unlocked Mode The period of time that can be set between 01 and 99 seconds for which the electrical locking hardware can be unlocked to allow entry to the building Duration of Door Latched Mode The period of time that can be set between 01 and 99 minutes for which the electrical locking hardware can be held in the unlocked position This feature is activated by entering the user code followed by O and is useful on occasions such as deliveries Operating Mode Once the user code has been entered the unit will switch for the duration of the Door Unlocked Setting to allow entry to the building and the green LED will flash at a rate of one per second An incorrect code will result in the red LED flashing once and the unit will return to standby Standby Mode The Mode in which the keypad is not in use and the function to which it returns after it has completed an operation Or if an operation is not concluded a period of time that can be adjusted from O1 to 99 seconds will lapse before the keypad reverts to standby mode This will also occur in programming The period of time taken to revert back to the standby mode this can be adjusted from 1 to 99 seconds This will also occur in programming Duration of the Exit Button Override Mode The period of time that can be set between 01 and 99 seconds for which the electrica
6. l locking hardware can be unlocked to allow exit from the building Setting Up 1 Factory Default Settings The Master Default Code is a 5 digit number and is factory set at 12345 The Duration of Door Unlocked Mode to unlock the electrical locking hardware is factory set at 10 seconds The Duration of Door Latched Mode to unlock the electrical locking hardware is factory set at 10 minutes The Exit Button Time Delay to unlock the electrical locking hardware is factory set at 10 seconds The Duration the Exit Button Override Mode is factory set at 10 seconds 2 Resetting the Master Code to Either 4 or 5 Digits This function only needs to be carried out if the master code is to be changed to a 4 digit code or having set a 4 digit code a change back to a 5 digit code is required Note that using this function will erase the memory of the keypad and will therefore delete all of the User Codes from 01 50 If this function is to be carried out after initial programming the existing User Codes should be recorded before hand Disconnect the power to the keypad Press either button 4 or 5 depending on whether a 4 or 5 digit code is required and keep it pressed Apply power to the keypad and wait until the green LED is lit before releasing the button The red LED should now be lit Enter the first digit of the new master code and keep it pressed until the red LED is not lit and then release Enter the remaining digits of the new mas
7. ter code the red LED should not be lit when each digit is pressed until the full code had been entered where it will light for approximately three seconds followed by the green LED flashing in standby Write down the master code Fitting Instructions for Ritekey 30 01 Rev 3 June 2005 3 To Change the Master Code Enter the default or old master code and wait for the LED to come on Enter the default or old master code for a second time and wait for the green to come on e Press keys OO and wait for the red LED Enter the new master code and the green LED will flash in standby Write down the new master code and keep it in a safe place Do not use the master code as a user code The green LED will flash in standby 4 To Create Change the User Code Enter the 4 or 5 digit master code and wait for the red LED to come on Enter the master code for a second time and wait for the green LED to come on Press any two keys i e 01 to 50 to store the User Code Position Number and wait for the red LED to come on Enter the new User Code which must consist of 4 digits for a 4 digit master code and 5 digits for a 5 digit master code Regardless of the number of digits do not use the master code as a user code Do not use the same User Code for other User Code Position Numbers e Write down the new 2 digit User Code Position Number and the new 4 or 5 digit User Code number 5 Changing the Delay for the Back to Standby Mode
8. utton Override Mode Enter the master code and wait for the red LED to light Enter the master code for the second time and wait for the green LED to light Press keys 99 and the green LED will light Press any two keys from 01 to 99 for the new time delay in seconds 01 being 1 second and 99 being 99 seconds The green LED will then flash in standby Fitting Instructions for Ritekey 30 01 Rev 3 June 2005
Download Pdf Manuals
Related Search