EF24-70mm F/2.8L II USM - The-Digital
Contents
1. mm DNIC MM 1 Rotate the zoom ring to the 2 Slide the zoom ring lock widest position 24 mm lever in the direction indicated by the arrow To release the zoom ring slide the zoom ring lock lever in the direction opposite to the arrow H Q The zoom ring can only be locked at maximum wide angle ENG 7 5 Infinity Compensation Mark Infinity compensation mark Distance index To compensate for shifting of the infinity focus point that results from changes in temperature The infinity position at normal temperature is the point at which the vertical line of the distance scale L mark is aligned with the distance index 0 For accurate focusing in MF on subjects at infinity distance look through the viewfinder while rotating the focusing ring ENG 8 6 Hood The EW 88C hood cuts out unwanted light and protects the front of the lens from rain snow and dust eAttaching To attach the hood align the hood s attachment position mark with the red dot on the front of the lens then turn the hood as shown by the arrow until the lens red dot is aligned with the hood s stop position mark Button eRemoving To remove the hood hold down the button on the side and turn the hood in the direction of the arrow until the position mark on the hood aligns with the red dot The hood can be reverse mounted on the lens for storage2. Do not look at the sun or a bright light source through the lens or camera Doing so could result in loss of vision Looking at the sun directly through the lens is especially hazardous Whether it is attached to the camera or not do not leave the lens under the sun without the lens cap attached This is to prevent the lens from concentrating the sun s rays which could cause a fire Conventions used in this instruction o Warning to prevent lens or camera malfunction or damage il Supplementary notes on using the lens and taking pictures ENG 2 AN Safety Precautions This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Do not make any changes or modifications to the equipment unless otherwise specified in the instructions If such changes or modifications should be made you could be required to stop operation of the equipment This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the in
3. 28 x 7 95 inch at 0 38 m 1 25 ft Filter Diameter 82 mm 3 23 inch Max Diameter and Length 88 5 x 113 0 mm 3 48 x 4 45 inch Weight Approx 805 g 28 4 oz Hood EW 88C Lens Cap E 82U Case LP1219 The lens length is measured from the mount surface to the front end of the lens Add 21 5 mm when including the lens cap and dust cap The size and weight listed are for the lens only except as indicated Extenders cannot be used with this lens In addition there are no close up lenses designed for use with this lens Aperture settings are specified on the camera All data listed is measured according to Canon standards Product specifications and appearance are subject to change without notice ENG 11 Canon CT1 8579 005 0812Ni CANON INC 2012
4. Canon EF LENS EF24 70mm f 2 8L Il USM I T EN hd ja AF ULTRASONIC Instructions Thank you for purchasing a Canon product Canon s EF24 70mm f 2 8L Il USM is a high Features performance standard zoom lens for use with EOS 1 cameras USM stands for Ultrasonic Motor Use of super UD lens elements UD lens elements and two types of aspherical lens elements giving superior definition Using a fluorine coating on the foremost and rearmost lens surfaces allows adhered dirt to be removed more easily than before Ultrasonic motor USM for fast quiet autofocus Manual focusing is available after the subject comes into focus in autofocus mode ONE SHOT AF Circular aperture for producing beautiful softfocus images Tight seal structure ensures excellent dustproof and drip proof performance ENG 1 Safety Precautions Handling Cautions If the lens is taken from a cold environment into a warm one condensation may develop on the lens surface and internal parts To prevent condensation in this case first put the lens into an airtight plastic bag before taking it from a cold to warm environment Then take out the lens after it has warmed gradually Do the same when taking the lens from a warm environment into a cold one Do not leave the lens in excessive heat such as in a car in direct sunlight High temperatures can cause the lens to malfunction Safety Precautions
5. Q If the hood is not attached properly vignetting darkening of the perimeter of the picture may occur When attaching or detaching the hood grasp the base of the hood to turn it To prevent deformation do not grasp the rim of the hood to turn it ENG 9 7 Filters sold separately You can attach filters to the filter mounting thread on the front of the lens Q Only one filter may be attached If you need a polarizing filter use the Canon Circular Polarizing Filter PL C B 82 mm To adjust the polarizing filter first remove the lens hood 8 Extension Tubes Sold Separately You can attach extension tube EF12 Il or EF25 Il for magnified shots The shooting distance and magnification are shown below Focusing Distance Range mm Magnification x Close distance Long distance Close distance Long distance 24mm 178 190 0 63 0 50 EF12 II 70mm 259 523 0 45 0 18 24mm Incompatible EF25 Il 70mm 229 331 0 74 0 41 Fil MF mode is recommended for accurate focusing ENG 10 Specifications Focal Length Aperture 24 70mm f 2 8 Lens Construction 13 groups 18 elements Minimum Aperture f 22 Diagonal 84 34 Angle of View Vertical 53 19 30 Horizontal 74 29 Min Focusing Distance 0 38 m 1 25 ft Max Magnification 0 21x at 70 mm 2 76 inch Field of View 369 x 554 134 x 202 mm 14 53 x 21 81 5
6. r at cost After detaching the lens place the lens with the rear end up to prevent the lens surface and contacts from getting scratched If the contacts get soiled scratched or have fingerprints on them corrosion or faulty connections can result The camera and lens may not operate properly If the contacts get soiled or have fingerprints on them clean them with a soft cloth If you remove the lens cover it with the dust cap To attach it properly align the lens mount index and the O index of the dust cap as shown in the diagram and turn clockwise To remove it reverse the order ENG 5 2 Setting the Focus Mode 3 Zooming 0 iem Pi AFi cME Y To shoot in autofocus AF mode set the focus To zoom rotate the zoom ring mode switch to AF To shoot in manual focus MF mode set the focus mode switch to MF and focus by turning the focusing ring The focusing ring always works regardless of the focus mode Fi After autofocusing in ONE SHOT AF mode focus manually by pressing the shutter button halfway and turning the focusing ring Full time manual focus Q Be sure to finish zooming before focusing Zooming after focusing can affect the focus ENG 6 4 Fixing the Zoom Ring The zoom ring can be fixed to keep the lens at the shortest point This function is convenient for carrying a camera on a strap because it prevents the lens from extending
7. structions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 ENG 3 Nomenclature Focus mode switch 6 Hood mount 9 Distance scale 8 Zoom ring 6 Rubber ring 5 Filter Mounting Thread N AS 2 10 Focusing ring 6 Contacts 5 Zoom ring lock lever 7 Lens mount index 5 For detailed information reference page numbers are provided in parentheses ENG 4 1 Mounting and Detaching the Lens See your camera s instructions for details on The lens mount has a rubber ring for enhanced mounting and detaching the lens dust and water resistance The rubber ring may o cause slight abrasions around the camera s lens mount but this will not cause any problems If the rubber ring becomes worn it is replaceable by a Canon Service Cente
Download Pdf Manuals
Related Search