iRZ Q24PL001 GPRS class 10 GSM modem USER MANUAL
Contents
1. USER MANUAL GSM modem iRZ Q24PL001 User Manual 1 automation Contents Safety Requirement ie atean ea etti qe aia 3 General Informatica en tin rid e lc FOURNIE cad ue USE Ee EU e ee Lahte daa ed 4 2 1 P rpose ofthe device 5n sn testen indo ete et ieri e E od dede Pepe en sU HIR adu EROR RU Ped ea diaria dre 4 2 2 COMMBU PAL To a EA A ERE 4 2 3 PAE AMIN UCTS cadet obse detis ces ie aa alea gute soucteesuoceaaes ie eer tub LEE dr a saal UP cea 4 2 4 Exterior dppe ratiGe eiit ien idt res EH LIRE RO ae Lea E add 6 235 Interface AM 7 2 6 Modem Status Indication enne enne ennt entente nien ete sentes trennen nne 9 Son OWERRINISUTICARU RR 10 3 1 ouem di da 10 3 2 Control Restarting and Power Off sse eene enne nnne nn entree nennen ener 10 GSM modem iRZ Q24PL001 ing User Manual automation 1 Safety Requirements Restrictions for the usage of the device in the vicinity of other electronic devices e turn off the modem in hospitals or in the vicinity of medical equipment e g cardiostimulators hearing aids It can cause interference for medical equipment e turn off the modem in aircrafts Take measures against accidental activation e turn off the modem in the vicinity of gas filling stations chemical enterprises blasting work places It can cause interference to technical devices e ata short range the modem may cause harmful i2. SIM card in the modem the SIM card must be enabled To do this you need e to extract the SIM tray by pressing the SIM tray extract button Fig 2 4 1 e to install the SIM card into the SIM tray e to insert the SIM tray with the SIM card into the modem No strong physical efforts must be applied while installing the SIM card Connect the GSM antenna to the antenna connector as well as the commutating cable RS232 Feed power supply to the modem through the connector RJ11 Fig 2 4 2 Note GSM antenna data cables and electrical power unit are not included in the complete set configuration After the power supply feeding registration occurs automatically which is signaled by the green indicator frequent flashing After the registration is completed the modem jumps to the operating mode the green indicator flashes less frequently Table 2 6 1 Note GSM antenna switching cables and power supply not included in complete set 3 2 Control Restarting and Power Off The modem control is performed by standard AT commands For additional information and support visit the manufacturer s site www radiofid ru Modem restarting can be carried out by the following ways e by the program method through AT commands e by temporary power off 10
3. not more than 76x53x31 mm e weight not more than 100 g e operating temperature range from 20 C to 50 C e storage temperature range from 40 C to 65 C Interfaces connector RJ11 for power supply connection connector DB15 for connection of the data cable RS 232 audio interface connection connector SMA for GSM antenna connection GSM modem iRZ Q24PL001 ing User Manual automation 2 4 Exterior appearance Modem 024PL001 is a compact device designed in solid and lightweight aluminum housing The exterior appearance is represented on Fig 1 4 1 and Fig 1 4 2 Fig 2 4 1 Front view SV 8 30 VDC RS 232 a MS Fig 2 4 2 Back view On the figures the digits signify the following 1 SIM card tray SIM card tray extracting button network LED indicator connector SMA for GSM antenna connection Connector for power supply connection Connector DB15 RS232 for data cable connection and audio interface S A M GSM modem iRZ Q24PL001 ing User Manual automation 2 5 Interfaces 2 5 1 Connector DB15 RS232 RS232 audio interface The connector is used for connection to the control device exchange protocol RS232 Fig 2 5 1 Connector DB15 Table 2 5 1 Purpose of the connector pins Purpose Availability of carrier wave Data transmission 3 Jnotused Non inversed microphone and power supply input Inversed microphone input 6 RXD Modem PC__ Data reception Readi
4. ness of data 8 DTR PC Modem Availability of data receiver 9 GND general System housing 10 SPKP Non inversed headphone output Availability of transmission Request for transmission Call signal Reset active low Inversed headphone output GSM modem iRZ Q24PL001 RE User Manual automation 2 5 2 Power supply connector The connector is used for connection of electric power supply Fig 2 5 2 Power supply connector Table 2 5 2 Purpose of power supply connector pins Contact Signal Purpose 1 GPIO Digital Input Output 2 INTR Synchronized interrupt output active low 3 GND System housing 4 12B Positive pole of DC supply voltage Protected with a fuse and the protection circuit against voltage surge with voltage infeed rate more than 30V and incorrect polarity GSM modem iRZ Q24PL001 ing User Manual automation 2 6 Modem Status Indication LED indication is provided in the modem for connection status indication Table 2 6 1 Connection status indication Indication mode Operation mode Turned off Modem is turned off or there is an emergency situation 600 ms on 600 ms Modem is not registered in the network off 75 ms on 3 s off Modem is registered in the network iR automation GSM modem iRZ Q24PL001 User Manual 3 Connection and Setting Up 3 1 Connection Before feeding the power supply you need to install the
5. nterference to TV and radio receivers Prevent the modem from dust and moisture Improper use deprives you of all warranty claims GSM modem iRZ Q24PL001 User Manual iR automation 2 General Information 2 1 Purpose of the device The modem iRZ Q24PL001 is a structurally accomplished GSM modem designed for reception and transmission of data text messages and telecopies It is excellently adjusted both for mobile Internet Access and for industrial applications telemetry wireless data collection from sensors remote surveillance monitoring and signaling The modem is assembled based on the GSM module MC55i Cinterion The control is performed by means of standard AT commands The modem is equipped with light emitting diodes LEDs enabling to monitor the status of connection 2 2 Configuration Complete set of the GSM modem IRZ Q24PL001 e modem IRZ Q24PL001 e label e factory box 2 3 Parameters Basic parameters e frequency ranges GSM 850 900 1800 1900 mHz e power output o 2W class 4 for EGSM900 o IW class 1 for GSM1800 GPRS class 10 MC class B CSD up to 14 4 kbps SMS voice transmission fax group 3 class 1 Electric power supply e power supply voltage from 9 to 30 V e absorbed current not more than o with power supply voltage 12 V 300mA o with power supply voltage 24 V 150mA GSM modem iRZ Q24PL001 User Manual RE automation Physical parameters size
Download Pdf Manuals
Related Search