USER MANUAL FL – 185
Contents
1. FL 185 Keep away from children and amateurs This product is designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc The minimum distance between light output and the illuminated surface must be more than 0 5 meters Always fix the fixture with an appropriate safety rope The maximum ambient temperature of 45 C must never be exceeded Operate the device only after having become familiar with its functions Features Innovative DJ scanner with rotating gobos 7 different dichroic colour fiitres and white Rainbow effect with adjustable speed in both directions Gobo wheel with 6 gobos plus 1 glass gobo open and blackout Strobe effect with adjustable speed 1 10HZ via shutter DMX controlled operation Fuzzy Sound Control program continues automatically during periods without music or bass beat Control Board with display e Manual focus Lamp MSD 250 DMxX control via every standard DMxX controller e 6 DMX control channels INSTALLATION Installing Replacing the lamp DANGER TO LIFE Only install the lamp with the device switched off Unplug from mains before Before replacing the lamp unplug mains lead and let the lamp cool down approx 10 minutes Procedure Step 1 Unscrew the fixation screws of the lamp system and carefully remove it from the housing Step 2 If replacing the tamp remove the old lamp from the lamp holder Step 3 Inser2. FL 185 USER MANUAL FL 185 INTRODUCTION Thank you for having chosen a mini barrel beetle You will see you have acquired a powerful and versatile device Unpack your unit Before you initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initial start up If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel During the operation the housing becomes very hot Do not switch the device on and off in short intervals as this would reduce the lamp s life Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics www flash butrym pl 1
3. mode is active select n2n and the unit will be at automatic mode 3 master slave mode Press the menu button till it shows 5 and set the unit at 515 by pushing the button up and down unit works at master slave mode In the same way set the other three units respectively at 525 535 545 and the four units work synchronized the red led informs about it Control board Ti DOWN Ri iP Gh MENU dh Microphone 10 Red LED If the devices should work independently from each other make sure that they have different start addresses Main functions of the control board d O01 1 After connecting the unit to the controller switch on the unit and wait until the fixture reset has finished Press the Menu button till it shows d and 001 address by pushing the up and down buttons Confirm by pressing the Menu button In this case the unit is under DMX 512 protocol mode In the same way use the Up and Down keys to set the units at different address ANIA AMen Anan 2 Press the button Menu till it shows n and next by pushing the button up and down choose the option nin to activate the sound active mode n2n by pushing the button up and down and the unit at automatic mode n3n and the unit stops working 3 Press the Menu button till 5 shows and set the unit at 515 by pushing the up and down In the same way set the other three units at 525 535 and 545 and now the fo
4. ng the fuse unplug mains lead Replacing the fuse Before replacing the fuse unplug mains lead Procedure Step 1 Open the fuse holder on the rear panel with a fitting screwdriver Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Close the cover TECHNICAL SPECIFICATIONS Power supply 230 V AC AC 50Hz Power consumption 300 W DMxX control channels 6 DMX 512 connection 3 pin XLR Flash rate 10 Hz Number of colors 7 dichroic white Number of gobos 7 gobos and open ONE GLASS GOBOS INCLUDED Fuse 250V 5A Dimensions 670x 270 x 260mm Weight 13 0 kg www flash butrym pl 5
5. t the lamp into the lamp holder Step 4 After replacing of the lamp screw down the fixation screws Step 5 Adjust the lamp DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m On the back of the mini barrel beetle you can find an XLR jack DMX Out and an XLR plug DMX In which can be used for connecting several devices Choose the device which is to control the effects Connect the DMX OUT jack with the DMX IN plug of the next device DMX 512 connection connection between fixtures The wires must not come into contact with each other Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected www flash butrym pl 2 FL 185 Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture Connection with the mains Connect the device to the mains with the enclosed power supply cable OPERATION 1 DMXControtling The Control Board at the back of the base of the unit allows you to assign the DMX fixture address which is defined as the start channel If the devices should work independently from each other then make s
6. ur units will work synchronized www flash butrym pl 4 FL 185 Cleaning and maintenance Disconnect from mains before starting maintenance operation DANGER TO LIFE We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches CAUTION The objective lens will require weekly cleaning as smoke fluid lends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Installing Replacing the lamp Replacing the fuse lf the lamp burns out it is very possible that the fuse might damaged too Only replace the fuse by a fuse of the same type and rating Before replaci
7. ure that each device has a different start channel After having addressed all items you may now start operating these via your lighting controller After switching on the item will automatically detect whether DMX 512 data is received or not DMX channels Channel 1 0 175 degrees PAN movement Channel 2 0 85 degrees TILT movement Channel 3 7 colors plus white 0 16 WHITE 17 33 VIOLET 34 51 GREEN 52 73 LIGHTBLUE 74 90 PINK 91 105 YELLOW 106 124 DARKRED 125 134 DARKBLUE 135 255 THE CONTINOUS COLOR CHANGE WITH THE POSSIBILITY OF SPEED AND DIRECTION ADJUSTING Control channel 4 GOBO WHEEL WITH ONE GLASS GOBO 0 15 OPEN 16 31 GOBO1 32 47 GOBO 2 48 63 GOBO 3 GLASS GOBO 64 79 GOBO 4 80 96 GOBO 5 97 111 GOBO 6 112 255 GOBO CHANGE WITH INCREASING SPEED Control channel 5 GOBO ROTATION the possibility of adjusting the speed and direction Control channel 6 ON OFF STROBE 0 5 Shutter closed 6 128 Dimmer control 129 131 Reset after 3 5 seconds 132 139 No function Shutter open 140 199 Strobe effect with increasing speed 200 249 Random strobe effect with increasing speed 250 255 No function Shutter open www flash butrym pl 3 FL 185 2 sound active automatic mode Press the menu button till it shows n on the display and select nin by pushing the button up and down and now the unit at sound
Download Pdf Manuals
Related Search