Chilling/Heating Incubators
Contents
1. a full 12 month warranty The unit is very compact measuring only 6 5 16 5 cm wide x 8 75 22 23 cm deep x 3 5 5 6 cm high without the sample block It weighs 6 5 pounds 2 9 kg It is UL CSA and CE compliant IC25 sample program 10 steps 2 cycles 80C 70C 60C 50C 40C 30C 20C 10C 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 Time minutes The graph above shows a temperature and time profile that can be stored in memory in the IC25 and rerun at any time The Model IC22 is a 2 position non programmable chilling heating dry bath It is like the IC20 except that it has 2 chilling heating positions that can be set to the same temperature or 2 different temperatures The tem perature range for both positions is 102C to 1002C It has an RS232 1 0 port for recording data or for control ling the unit from a computer The built in data logger can store 8110 data points in 1 second 1 minute or 5 minute intervals It accepts the full range of sample blocks listed on page 7 for centrifuge tubes assay plates Model IC10 Electronic Ice Cube The Model IC10 called the Electronic Ice Cube is an uncon trolled Peltier driven chilling device that chills only It will go to 302C below room temperature The unit is designed to replace an ice bucket No more water mess or changing ice as it melts T2. impervious to most chemicals They are excellent for working with solu tions in a vessel They will heat to 450 C in about 2 minutes Ceramic tops heat quickly but not as evenly as cast aluminum tops Milled flat Cast Aluminum Tops The cast aluminum tops are milled flat to 0 01 0 254mm corner to corner They are excellent for work ing with solids directly on the heater surface They heat more evenly across the surface than the ceramic tops and are not as chemically resistant Maximum temperature is 400 C Stirrers All stirring units are specified to stir from 100 to 1500rpm The stirrers are an optimum combination of motor and magnet to couple strongly with the stir bar in the solution All units should be able to stir 2 liters of water The analog and DigiLog units have open loop stirrer controls All digital units have closed loop stirrer controls and will control stirring speed exactly even through viscosity changes General C onstruction All units are housed in cast aluminum chassis and painted with chemically resistant epoxy paint They are designed to keep spills out of the case All controls are mounted well forward of the heater top for safety The DigiLog tops are 6 x 6 15 24cm x 15 24cm Features Models HP10 ST10 HS10 HP20 ST20 HS20 HP30 HP30A HS30 HS40 Analog Hybrid Digital P rogrammable Controls A A A H H H D D D R Ceramic or Cast Aluminum Top C C G C C iG c A C C Plate Surface S
3. com Dealer In China ShangHai Aoran Inc Head Office Address Rm303 Building 3 No 735 West Shangzhong Road Shanghai 200237 Website www aoran cn E mail service aoran cn Tel 86 21 64540781 64540791 Fax 86 21 64540715
4. fax or e mail us directly to order or to find the distributor closest to you For ordering information outside the USA please contact us for the distributor in your country We accept orders by VISA and MASTERCARD as well as company purchase orders How To Reach Us Mail Torrey Pines Scientific Inc 1780 La Costa Meadows Drive 101 San Marcos CA 92078 Phone 760 471 9100 or Toll Free inside the USA 866 573 9104 Fax 760 471 9310 E mail info torreypinesscientific com Web Site www torreypinesscientific com About Peltier Technology Many of our products are based on Peltier technology to heat and chill For those of you not familiar with this technology we have a brief description here Peltier or thermoelectric cooling heating is semiconductor based It has solid state material in a module that functions as a small heat pump By applying a low voltage DC power source to the module heat will be moved through the module from one side to the other One module face will be cooled while the other face heats This effect can be reversed by reversing the current flow through the module Thus the module can be used to heat or chill We apply this principle to our chilling heating incubators and chilling heating dry baths HPLC column chiller heater and chill ing heating mini circulator They are very efficient and very good at controlling temperature ABOVE BELOW and DIRECTLY AT ROOM TEMPERATURE They have very few moving parts and no c
5. like simple analog units Here are some features Digital Features e 3 digit display of heater power as a percent of total range for easy resetting No need to mark the heater knob or front panel Membrane Keyboard setting of all parameters Easy scroll up or down settings No mechanical controls at all Two memory keys for saving your 2 favorite combinations of temperature and stirring speed for one button instant recall at any time e Plate Hot red LED illuminates when plate temperature goes above 50 C and stays lit when the plate is hot even after the unit is turned off A really nice safety feature Main power ON OFF button on the front panel for easy safe access Prior settings are retained when the unit is turned off and the unit will return to those settings automatically when turned on again Indicator lights and ON OFF buttons for heater and stirrer power Turn either off with a single button Turn on again and the prior settings remain Heater power regulated even through changes in line voltage Heater temperature stays much more stable than standard analog units e Low plate temperature settings as low as 302C e Heater drive software written to go up to setting quickly Reduced heating times Analog Features e Inexpensive price These units cost less than most strictly analog units Compact size They are 10 25 4cm deep by 7 17 78cm wide by 4 5 11 43cm high Ru
6. speeds settable from 200 to 1000 rpm and a temperature range from 10 C to 100 C It has an RS232 I O port for recording data or for controlling the unit from a computer The built in data logger can store 8110 data points col lectable in 1 second 1 minute or 5 minute inter vals It accepts the full range of sample blocks listed on page 7 for centrifuge tubes assay plates vials and test tubes The unit is provided with a 12VDC bench top power sup ply that takes AC inputs from 100 to 260VAC 50 60 Hz It comes com plete with users manual 3 wire AC line cord for the country of use and a full 12 month warranty The unit measures 14 5 36 83 cm deep x 7 75 19 69 cm wide x 4 25 10 8 cm tall without a sample block It weighs about 10 pounds 4 5 kg It is UL CSA and CE compliant Model IC20 chilling Heating Dry Bath Model IC25 Fully Programmable Chilling Heating Dry Bath The Model 1C25 is the fully pro grammable version of the IC20 Like the 1C20 it does not shake but it can store 5 programs in memory of as many as 10 steps per program where each program step can be a temperature and time Each program can be repeated from 1 to 99 times automatically The IC25 can be set from 102C to 100 C It has an RS232 I O port for NEW Model IC 20XT Extended Chillin from 202C to 852C now available The Model 1C20 is a simple set and forget chilling heating dry bath Set the te
7. 16 mm test tubes 20 12 13 mm test tubes 620 5024 620 5025 620 5026 6 6 mm 5 12 13 mm 8 20 mm test tubes 30 6 mm test tubes and 3 20 mm test tubes 620 5028 ie 12 20 ml AA i scintillation 620 5030 620 5031 620 5032 vials 6 50 ml centrifuge tubes 4 slides for hydridization 30 2 0 ml with cover Eppendorf tubes 7 Chilling Heating Incubators There are 5 models of chilling heating convection incubators in our product range All are Peltier based and have no CFCS or compres sors to worry about They are reliable accurate and easy to use Two are fully programmable Four have temperature ranges from 4 0 C to 70 0 C and all read and regulate temperature to 0 19C Because these units chill and heat they can control temperatures at or near room temperature and they will hold that temperature regardless of changes in room temperature All have built in timers RS232 I O ports for recording data or controlling the units by computer and the programmable models have built in temperature ramping They have built in watchdog circuits and power failure protection that will return the unit to what it was doing when power returns after a power failure They all share common applications They are extensively used for growing protein crystals The chart below will show their features and their differences SOME APPLICATIONS Protein crystal growth Incubating marine sample below ambient Enzyme reactions
8. NA libraries at your work station e Incubating samples at 37 C e Storing samples at ice bucket temperatures without the ice e Incubating or chilling omnes in 96 and 384 well assay p e PCR sample prep Hybridizations ates e General molecular biology Features C25 Peltier Driven Yes Built in Orbital Shaker Yes Stores 5 Programs in Memory Yes Digital C ontrols Yes Number of Sample Blocks 1 Temperature Range 10 to 100C Temperature Readability 1C Temperature Accuracy 1C Temperature Stability 1C PID Temperature Control Yes Temperature Uniformity C Yes 30 Day Countdown Timer Yes Audible Alarm Yes Auto Off User Settable Yes RS232 I O Port Yes Data Logger Yes Operating Power 12VDC Models ScC20 IC22 IC25 Yes Yes Yes Yes No No No No Yes Yes Yes Yes 1 2 1 10 to 100C 10 to 100C 10 to 100C 1C 1C 1C 1C 1C 1C IC 1C 1C Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 12VDC 100 115 230VAC 12VDC IC20 Yes No No Yes 1 10 to 100C 1C 1C 1C Yes Yes Yes Yes Yes Yes Yes 12VDC IC10 Yes No N A No 1 30C Below Ambient N A N A N A N A Yes N A N A N A N A N A 12VDC The SC25 is a fully programmable chilling heating dry bath with built in orbital mixer The unit can store 5 programs in memory of as many as 10 steps per program where each step can be a temperature time and mixing speed Ea
9. an RS232 I O port for datalogging or for controlling the unit from a computer or chromatograph The C030 also has a power failure reset system that will reset the unit to the temperature it was running when power returns It has electronic calibration that is easily reset to local standards if nec essary The C030 can be ordered in models for 100 or 115VAC 50 60 Hz 2 amp or 230VAC 50 60 Hz 1 amp It comes complete with users manual two sizes of O rings for mounting columns fused and switched AC input module 3 wire line cord for the country of use and 12 month warranty The unit measures 25 5 64 77 cm tall x 8 75 22 23 cm wide x 13 5 33 66 cm deep and weighs 25 pounds 11 26 kg All are UL CSA and CE compliant Model RT10 Variable Speed Rotating Mixer The Model RT 10 variable speed rotat ing mixer is designed to mix 0 5 and 1 5ml centrifuge tubes in an end over end motion and 15ml and 50ml tubes in a horizontal rolling motion at speeds varying from 4 to 40 rpm using a simple knob control The unit is provided with a mounting rack that holds 50 0 5 ml centrifuge tubes and 48 1 5ml centrifuge tubes Accessory racks can be ordered that hold 16 15ml tubes or 6 50ml tubes Changing from the provided rack to accessory racks can be done in just minutes The rod holding the racks is easily removed for changing from one rack to another The unit is compact measuring only 4 5 11 43 cm wid
10. and deactivations Hybridizations e Ligations at 14 0 C to 16 0 C e Storing oocytes at 17 0 C e Culture growth below above and at room temperature e Storing DNA libraries Features Models IN30 IN35 IN40 IN45 IN20 Peltier Driven Yes Yes Yes Yes Yes Stores Multistep Programs in Memory No Yes No Yes No Digital Display and C ontrol Yes Yes Yes Yes Yes Temperature Range in Degrees Centigrade 4 0 to 70 0 4 0 to 70 0 4 0 to 70 0 4 0 to 70 0 10 0 to 50 0 Temperature Readability 0 1C 0 1C 0 1C 0 1C 0 1C Temperature Accuracy 0 2C 0 2C 0 2C 0 2C 0 2C Temperature Stability 0 1C 0 1C 0 1C 0 1C 0 1C PID Temperature Control Yes Yes Yes Yes Yes Temperature Ramping No Yes No Yes No Chamber Uniformity 0 5C 0 5C 0 5C 0 5C 0 5C Countdown Timer 99 hours 99 days 99 hours 99 days 30 days Audible Alarm for Timer Yes Yes Yes Yes Yes Auto Off User Settable Yes Yes Yes Yes Yes RS232 Port Yes Yes Yes Yes Yes Data Logger Built In No No No No Yes Chamber Volume 27 5L 27 5L 55L 55L 9 8L Chamber Height 12 12 24 24 ae Chamber Width 14 14 14 14 6 Chamber Depth 10 10 10 10 8 Operating Voltage 100 115 230VAC 100 115 230VAC 100 115 230VAC 100 115 230VAC 12VDC Number of Shelf Slots 4 4 6 6 6 Number of Shelves Provided 2 2 4 4 6 When chilling range is 16 0 C below ambient max Models IN30 and IN40 Chilling Heating Incubators The Models IN 35 and IN45 are fully programmable These un
11. asily repeated setting Once the tempera ture reaches its set point it will hold that temperature within 2 02C There are two MEM memory keys on each unit MEM1 and MEM2 Two frequently used heating stirring combinations may be saved in memory Simply set the stirrer and heater to those settings and then push and hold the MEM1 or MEM2 key depressed until the beep sounds Those settings are saved to memory The next time that sample is run just place it on the unit and touch the memory key The previously set heat and stir values will be run automatically ST20 available in LOOVAC 50HZ 0 5 amp 115VAC 60HZ 0 5 amp 220VAC 60 Hz 0 25 amp and 230VAC 50 Hz 0 25 amp HP20 available in LOOVAC 50Hz 5 amp 115VAC 60Hz 5 amp and 230VAC 50Hz 2 5 amp HS20 available in 100VAC 50Hz 5 amp 115VAC 60Hz 5 amp 220VAC 60Hz 2 5amp and 230VAC 50Hz 2 5 amp All models are 10 25 4cm deep by 7 17 78cm wide by 4 5 11 43cm high The HP20 weighs 6 pounds 2 7kg and the HS20 and ST20 weigh 7 pounds 3 15kg each All come complete with 3 wire AC line cord for the country of use users manual and_ full 12 month warranty All are UL CSA and CE compliant TORREY PINES SCIENTIFIC INC 1780 La Costa Meadows Drive 101 San Marcos CA 92078 Tel 760 471 9100 Toll Free within the USA 866 573 9104 Fax 760 471 9310 E mail info torreypinesscientific com Website www torreypinesscientific
12. ated com pletely of a green plastic making it translucent and making the samples visible at all times It has a tempera ture range from 10 02C to 50 0 C and controls accurately at or near room temperature and through changes in room temperature It can hold 12 assay plates on 6 shelves in a very small footprint on the bench and each shelf is made with holes to hold centrifuge tubes Two shelves hold 60 1 5 ml centrifuge tubes each two shelves hold 80 0 5 ml centrifuge tubes each and two shelves hold 192 0 2 ml PCR tubes each in two classic 96 well formats per shelf The unit has a backlit 2 line alphanumeric display with 16 characters per line a built in 30 day count down timer with alarm and user settable Auto Off an RS232 I O port for data col lection and control of the unit by a computer and a built in data logger that can collect 4055 data points in 1 second 1 minute or 5 minute inter vals The unit runs off 12VDC and comes complete with bench top uni versal power supply that can take inputs from 100 to 260VAC 50 60 Hz users manual AC line cord for the country of use and a full 12 month warranty The IN20 measures 8 20 3 cm wide x 14 5 36 8 cm deep x 18 45 7 cm high and weighs 18 pounds 8 2 kg It is UL CSA and CE compliant Model CB20 constant Temperature Chilling Heating Mini Circulator The Model CB20 is a Peltier based chilling heating constant tempera ture small volume circu
13. b i i ah i HH BATERE E e EEEE eet SEER ERE LAL 2006 CATALOG i TORREY PINES SCIENTIFIC INC Temperature Control Specialists EchoTherm Digital and Analog Chilling and Heating Laboratory Equipment tt Pit Ts At Torrey Pines Scientific Inc we design develop manufacture and sell chilling and heating laboratory equipment with analog and digital controls for use in the biotech pharmaceutical environmental chemical biomedical and other laboratories Torrey Pines Scientific Inc was founded in 1995 in Solana Beach California twenty miles north of San Diego the west coast capital of the biomedical industry We are a manufacturing company whose principals have over 50 years experience in designing and manufacturing high quality unique analog and digital chilling and heating equipment New products and new applications for existing products are being developed continuously by our marketing and engineering staffs to make your laboratory job easier We are dedicated to excellence and innovation and we take pride in our superior customer service All our products are made in the USA and will be certified by UL CSA and CE or equivalent agencies for safety Where To Order We sell through some of the finest stocking distributors in the USA and around the world These distributors are trained to sell and service our products You can order directly from them or you can order from us You can call
14. ch program can be repeated from 1 to 99 times automatically The SC25 has speeds for mixing set table from 200 to 1000 rpm The temperature range is 102C to 100 C The unit has an RS232 I O port for recording data or for controlling the unit from a computer The built in data logger can store 7825 data points collectable in 1 second 1 minute or 5 minute intervals It accepts the full range of sample blocks listed on page 7 for centrifuge tubes assay plates vials and 7c test tubes The unit is provided with a 12VDC bench top power supply that takes AC inputs from 100 to 260VAC 50 60 Hz It comes complete with users manual 3 wire AC line cord for the country of use and full 12 month warran pm ee ty The unit measures only 14 5 36 83 cm deep x 7 75 19 69cm 30 40 wide x 4 25 10 8 cm tall without a sample block It weighs about 10 pounds 4 5 kg It is UL CSA and CE compliant SC25 10 step sample program 2 cycle orbital shaker enabled 1000 RPM 900 RPM 800 RPM 700 RPM 600 RPM 500 RPM 400 RPM 300 RPM 200 RPM 100 RPM 0 RPM 50 60 70 80 90 100 110 120 130 Minutes The graph above shows a temperature time and mixing speed profile that can be stored in memory in the SC25 and rerun at any time Model SC20 orbital Mixing Chilling Heating Dry Bath The Model SC20 is a non programmable version of the SC25 Like the SC25 the SC20 has a built in orbital mixer with
15. e by 13 7 34 cm long by 6 75 17 15 cm high It weighs only 5 pounds 2 25 kg It is powered by a 12VDC power supply that operates from 100 to 260VAC 50 60Hz inputs It draws less than 1 amp The unit comes complete with rotator racks for 0 5m and 1 5ml centrifuge tubes 12 VDC bench top power supply that takes AC inputs from 100 to 260VAC 50 60Hz 3 wire AC line cord for the country of use and users manual It has a full 12 month warranty Itis UL CSA and CE compliant See Price list for Accessories holding 15 ml and 50 ml centrifuge tubes 11 Digital DigiLog and Analog Stirrers E aie Torrey Pines Scientific hot plate product lines include three models of analog three models of DigiLog and four models of digital units The analog and DigiLog product lines include a stirrer hot plate and stir ring hot plate The digital product line includes a hot plate with ceram ic top a hot plate with milled flat cast aluminum top a stirring hot plate and a fully programmable stir ring hot plate About These Products Heater Tops We manufacture the entire line with solid ceramic tops Our digital hot plates also can be ordered with a milled flat cast aluminum heater top The analog and digital units have tops that are 8 x 8 20 32cm x 20 32cm Ceramic Tops The ceramic tops are solid ceramic glass sheet cut to size and mounted in a cast aluminum frame The tops are white flat and
16. ggedness Will support over 30 pounds 13 5kg Simple to use Scroll up and scroll down settings e Simple to service if needed Service by anyone No special training required e Fused AC input line continued on the next page 15 DigiLog Stirrers Hot Plates and Three models of DigiLog units are available a hot plate Model HP20 a stirrer Model ST20 and a stirring hot plate Model HS20 All use the same compact rugged cast aluminum chassis that is designed to keep spills out of the case All controls are mounted forward of the heater plate for safety All electronic controls are on one simple PC board and all con trols have red indicator LED s that illuminate when activated The stirrer features a circular disk magnet capable of lifting 20 pounds 9kg coupled to a strong stirrer motor making these units capable of stirring 2 liters of aqueous solution The stirrer range is from 100 to 1500 rpm The heating units Models HS20 and HP20 will heat to 4502C in less than 5 minutes using just 400 watts of heating power The heater is set using a digital display and UP DOWN arrows to set the heater power in percentage of full power in 1 increments The lowest setting is below 30 C on a setting of 1 The 50 setting is roughly one half of 450 C or about 250 C when the ambient room temperature is added This type of control and indicator is not designed to give an exact temperature setting just an e
17. he unit has the same size chilling plate as all the other units in this section and uses all the same sample blocks and covers It is very small and uses virtually no bench Sample Blocks and Covers All of the chilling heating dry baths above can use any of the sample blocks and covers listed here The blocks are precision machined from solid aluminum to exactly fit the tube shape and then black anodized for better heat transfer and protec tion from spills The bottom of the blocks is machined to nest on the dry 6 bath plates to prevent movement Magnets are used to keep blocks stable on shaking models Also custom blocks are available for any sample container on special order Clear polycarbonate covers are avail able for blocks and assay plates It is recommended that the larger cover NEW Model IC22XT Extended Chilling Range from 202C to 852C now available vials and test tubes The unit has 3 operating models One for 100VAC 50 60 Hz for Japan 115VAC 50 60 Hz for the US Canada and Mexico and 230VAC 50 60 Hz for the rest of the world It comes complete with users manual 3 wire AC line cord for the country of use and full 12 month warranty The unit measures 6 5 16 5 cm wide x 20 50 8 cm deep x 3 5 8 8 cm high without sample blocks It weighs 13 pounds 5 85 kg It is UL CSA and CE compliant space It is supplied with a 12VDC bench top power supply that takes AC inputs from 100 t
18. if wanted stirring speed and time Each program can be instructed to repeat from 1 to 98 times Setting 99 times will repeat the program infinitely All programs are stored in CMOS There are no batteries to replace The HS40 can be used in the programmable and the non programmable modes The HS40 has a fully featured LCD that displays all parameters all the time It has a solid ceramic heater top framed in cast alu minum that is very white very flat and very chemically resistant The HS40 will heat and control temperature to 1 C from ambient to 450 C and is accurate to 1 of the setting It will heat the plate surface to 450 C in about 2 minutes It can be set to ramp temperatures up or down from 12C to 450 C per hour It has a platinum RTD temperature sensor in the heater top and a PID heater control loop designed specifically for setting and controlling the heater top directly There is a jack on the rear of the unit for an accessory platinum RTD probe for sensing solution temperatures directly It is tied together with a separate PID control loop designed specifically for controlling solutions in a vessel The custom LCD displays both plate and probe target and actual temperatures stirring speed count down timer in hours minutes and seconds to 99 hours with user settable Auto Off temperature ramping and program steps if in the programming mode The HS40 will stir from 100 to 1500 rpm while controlling to 10
19. ire grounded AC line cord for the country of use users manual and full 12 month warranty It measures 15 75 40 01 cm deep by 9 125 23 18 cm wide by 4 75 12 07 cm high and weighs 12 pounds 5 4 kg It is UL CSA and CE compliant Digital Hot Plate amp Stirring Hot Plate Accessories HS30 600 Probe immersion 6 stainless steel platinum RTD 3 lead HS30 601 Probe immersion 10 stainless steel platinum RTD 3 lead HS30 602 Probe immersion 6 Teflon platinum RTD 3 lead HS30 603 Probe immersion 6 glass platinum RTD 3 lead HS30 700 Temperature probe calibration kit Models HP30 amp HP30A Digital Hot Plates Above is the milled flat cast aluminum heater top for the HP30A This top heats very evenly and is recommended for heating solids directly 14 The Digital Hot Plates Models HP30 and HP30A are identical with the exception of the material of the heater top The HP30 has a solid ceramic heater top and the HP30A has a milled flat cast aluminum heater top The HP30 will heat to 450 C while the HP30A will heat to 400 C The HP30 with ceramic top is recommended for use with aggressive chemicals and high temperatures The HP30A is recommended for use with any solids placed directly on the heater top The HP30A5 aluminum top heats slower than the ceramic top but it also heats much more evenly across the surface It is milled flat corner to corner
20. its have a 2 line 16 character per line alphanu meric display showing all parameters when programming and running programs They can store 3 programs in memory for instant recall and use at any time Each program has ten steps available where each step is a temperature time and temperature ramp rate if wanted Steps can be set for running multiple ramp and soak cycles or for just running at one temperature for a given time and then switching automatically to The Models IN30 and IN40 are not programmable They are simple set and forget models Set the tempera ture and the unit will go there To change temperature simply key in another target The units are bench top in size The IN30 has 27 5 liter capacity and the IN40 has 55 liter capacity Both have a temperature range from 4 0 C to 70 0 C They have seamless white ABS plastic chambers with capped holes in the left side of the sheet metal case for routing cords for shakers or tubing another temperature At the end of each program is a cycle step which can be set to repeat the prior steps 1 to 99 times They also can be set to a single temperature without using the pro gram mode just like the IN30 and IN40 The IN35 has 27 5 liter capacity and the IN45 has 55 liter capaci ty Both have a tempera ture range from 4 0 C to 70 02C They have seam less white ABS plastic chambers with a capped hole in the left side of the sheet metal case for ro
21. ize 8 x 8 or 6 x 6 8X8 8X8 8X8 6X6 6X6 6X6 8X8 8X8 8X8 8X8 Heat Stir Heat and Stir H S H S H S H S H H H S H S Stirring Speed 100 1500RPM N A YES YES N A YES YES N A N A YES YES Temperature Range in Degrees C 100 450 N A 100 450 30 450 N A 30 450 ambient to 450 ambientto 400 ambient to 450 ambient to 450 Plate Hot Indicator NO N A NO VES N A YES YES YES YES YES Programs Stored in Memory NO NO NO NO NO NO NO NO NO VES 10 Steps per Program N A N A N A N A N A N A N A N A N A 10 Control Settings Stored in Memory NO NO NO YES YES YES YES YES YES YES Temperature Controlled by PID Controller Plate NO NO NO NO NO NO MES VES VES YES and Solution Temperature Controlled To 5C N A 5C 2C N A 2C 1C 1C 1C 1C Timer with Alarm and Auto Off NO NO NO NO NO NO YES YES YES YES RS232 I O Port NO NO NO NO NO NO YES MES YES YES 2 Liter Stirring Capacity N A YES YES N A YES VES N A N A YES YES Temperature Ramping NO N A NO NO N A NO YES YES YES YES Temperature Displayed To NO N A NO 1 of Range N A 1 of Range 1C 1C 1C ie Display All Parameters Continuously NO NO NO NO NO NO YES WES YES WES UL CSA and CE Approved YES XES YES YES VES YES YES YES YES YES 12 Digital Hot Plates and Stirring Hot Plates Model HS40 Fully Programmable Digital Stirring Hot Plate The Model HS40 is fully programmable through the membrane keypad It can store 10 programs in memory of as many as 10 steps each where astep is a temperature temperature ramp rate
22. lator with a temperature range from 4 0 C to 70 02C It can circulate up to 300 ml minute of solution from a 1000ml reservoir for controlling the temper ature of small remote samples like 10 water jacketed cuvettes for spec trophotometers It displays and controls temperature to 0 19C It is accurate to 0 2 C The circulator has a DC operated brushless mini pump with a variable flow control for pumping exactly the needed amount of temperature controlled solution for small samples The unit is very compact takes very little bench space and uses very little power It has a backlit 2 line alphanumeric display with 16 characters per line that constantly displays target and actual temperature and pumping rate The membrane switch is used for entering temperature and pump flow rate settings The unit has an RS232 I O port for controlling the unit from a computer or for collect ing temperature data The CB20 is provided with brass Swagelok fittings on the rear of the unit that accepts 1 8 inch D 1 4 inch O D plastic tubing Temperature is sensed with a 3 32 inch diameter stainless steel probe provided A six foot long extension for the probe is available as an acces sory The temperature measurement system is 100 ohm platinum RTD for accuracy Also included are al2VDC bench top power supply that takes AC inputs from 100 to 260VAC 50 60 Hz users manual 3 wire AC line cord for the country of use and full 12 month
23. mes or infinitely platinum RTD temperature sensor in the heater top and a PID heater top control loop designed specifically for setting and controlling the heater plate directly There is ajack on the rear of the unit for an acces sory platinum RTD probe for sensing solution temperatures directly that is tied together with a separate PID control loop designed specifically for controlling solutions continued on the next page 13 Digital Hot Plates and The custom LCD displays both the plate and probe target and actual temperatures stirring speed count down timer in hours minutes and seconds to 99 hours with user settable Auto Off that will set all functions to zero at the end of a count down timed event and temperature ramping used to increase or decrease temperature at a given rate Ramp rates can be set from 1 C to 450 C per hour The HS30 will stir from 100 to 1500 rpm while controlling the setting to 10 rpm The stirrer motor speed is optically sensed and then controlled by the microprocessor in the unit regardless of changes in sample viscosity The unit features electronic cali bration that is set at the factory and trace able to NIST and easily reset by the user to local standards if wanted or needed An RS232 O port for controlling the unit or for collecting data is provided The HS30 is available in 100 115VAC 50 60Hz 8 amp or 230VAC 50 60Hz 4 amp models It comes complete with six foot 3 w
24. mperature anywhere from 102C to 100 C and the unit goes there To change temperature simply set in another target and the unit goes to it The IC20 has an RS232 I O port for recording data or for controlling the unit from a computer The built in data logger can store 8110 data points collectable in 1 second 1 minute or 5 minute intervals It accepts the full range of sample recording data or for controlling the unit from a computer The built in data logger can store 7825 data points collectable in 1 second 1 minute or 5 minute intervals It accepts the full range of sample blocks listed on page 7 for centrifuge tubes assay plates vials and test tubes The unit is provided with a 12VDC bench top power supply that takes AC inputs from 100 to Range blocks listed on page 7 for centrifuge tubes assay plates vials and test tubes The unit is provided with a 12VDC bench top power supply that takes AC inputs from 100 to 260VAC 50 60 Hz It comes com plete with users manual 3 wire AC line cord for the country of use and full 12 month warranty The unit is very compact measuring 6 5 16 5 cm wide x 8 75 22 23 cm deep x 3 5 5 6 cm high without a sample block It weighs about 6 5 pounds 2 9 kg It is UL CSA and CE compliant NEW Model IC 25XT Extended Seas Range from 20 C to 8 now available 260VAC 50 60Hz It comes com plete with users manual 3 wire AC line cord for the country of use and
25. o 260 VAC 50 60Hz It comes complete with cable for a car cigarette lighter for field use users manual 3 wire AC line cord for the country of use and full 12 month warranty It measures 6 5 16 5 cm wide x 4 75 12 cm deep x 3 5 8 9 cm high It weighs 6 pounds 2 7 kg Itis UL CSA and CE compliant be used for most all applications Cover sizes are 6 15 24 cm long x 4 25 10 8 cm wide x 2 5 08 cm high for the smaller cover and 6 15 24 cm long x 4 25 10 8 cm wide x 3 5 8 89 cm high for the larger cover Precision Sample Blocks The block at the left is number 620 5013 and is for 30 1 5 ml centrifuge tubes The block measures 4 375 in 11 11 cm long by 3 0 in 7 62 cm wide by 1 75 in 4 45 cm thick All blocks are precision machined from solid aluminum to exactly fit the tube shape and black anodized for better heat transfer and protection from spills The bottom of the blocks are machined to nest on the plate to prevent movement Also custom blocks for any sam ple container can be made upon request a 620 5012 620 5013 620 5014 620 5015 40 0 5 ml centrifuge tubes 30 1 5 ml centrifuge tubes 15 1 5 ml and 40 0 5 ml 96 0 2 ml PCR plates and centrifuge tubes tube strips of 12 or 8 620 5016 620 5017 620 5018 V bottom U bottom 24 2 0 ml vials 96 well assay plates 96 well assay plates 620 5021 620 5022 620 5023 24 10 mm test tubes 12 15
26. o NIST Calibration easily can be reset by the user in the field to local standards if wanted or needed An RS232 I O port is provided for collecting data or for controlling the units from a computer The HP30 and HP30A are available in 100 and 115VAC 50 60 Hz 8 amp and 230VAC 50 60 Hz 4 amp models They come complete with 6 foot 3 wire ground ed AC line cord for the country of use user s manual and full 12 month warranty They measure 15 75 40 01 cm deep by 9 125 23 18 cm wide by 4 75 12 07 cm high They weigh 12 pounds 5 4 kg They are UL CSA and CE compliant Analog Stirrers Hot Plates and There are three models of analog units They are a magnetic stirrer Model ST10 hot plate only Model HP10 and stirring hot plate Model HS10 All are made in the same cast aluminum chassis painted with chemically resistant epoxy paint They are designed to keep spills out of the case and they have the controls mounted well for ward of the heater top for safety Heating and stirring controls are solid state with an individual indicator lamp that illuminates when the control is on All have the same very white very flat and very chemically resistant ceramic glass 8 20 32 cm by 8 20 32 cm top mounted in a cast alu minum frame All heaters are 600 watts The stirrer features a solid state control capable of stirring aqueous solutions from 100 to 1500 rpm The control has an OFF position fully coun
27. ompressors or gases 2 Chilling Heating amp Orbital Chilling Heating Dry Baths There are 5 models of digital chill ing heating dry baths and 1 model of analog chilling only dry bath in our product range They share many common features and applications with some features specific to indi vidual models The chart below will make the differences clear All have the same size plate 2 875 7 3 cm x 4 375 11 1 cm and all use the same sample blocks All the digital units have an RS232 I O port 30 day countdown timer with alarm and user settable Auto Off built in data logger electronic calibration back lit two line alphanumeric display with 16 characters per line and UP DOWN arrow front panel mem brane switch for complete control of all functions Two units are fully pro grammable and will store 5 routines in memory and two of the units have built in orbital shakers for mixing while heating or chilling They all control temperature to 1 C from 10 C to 100 C The analog unit chills only and to 30 C below ambi ent without controls It makes an excellent replacement for an ice bath All units are Peltier based with no compressors or CFC to worry about The chart below shows our complete range and features for each SOME APPLICATIONS e Maintaining 14 C for ligation reactions e Maintaining 17 C for storing oocytes e Enzyme reactions and deactivations e Storing enzymes and D
28. rpm The stirrer speed is optically sensed and controlled by the micro processor regardless of changes in sample viscosity The unit features electronic calibration that is set at the factory and traceable to NIST and easily reset by the Model asada Digital Stirring Hot Plates The Model HS30 is the easiest to use fully featured digital stirring hot plate ever made It has a solid ceramic heater top framed in cast aluminum that is very white very flat and very resistant to chemical spills The unit will heat and control temperature to 12C from ambient to 450 C and is accurate to 1 of the setting throughout the entire range It will heat the plate surface to 450 C in about 2 minutes using only 600 watts of power in the heater The unit has a user to local standards if wanted or needed An RS232 I O port for controlling the unit or for collecting data is provided The HS40 is available in 100 and 115VAC 50 60Hz 8 amp or 230VAC 50 60Hz 4 amp models It comes complete with 6 foot 3 wire ground ed line cord for the country of use users manual and full 12 month warranty It measures 15 75 40 01 cm deep by 9 125 23 18 cm wide by 4 75 12 07cm high It weighs 12 pounds 5 4kg Itis UL CSA and CE compliant See probes and accessories on pg 14 ip Sn ani THEE MIP The chart shows a program that can be stored in memory and run at any time The program can be set to repeat itself from 1 to 98 ti
29. ter clockwise and is continuous over 2702 of rotation from minimum to maximum The magnet is a circular disc with twenty pounds of pull strength capable of stirring more than two liters of aqueous solution The heater control has OFF LO and HIGH positions for quick setting and a smooth infinite control of about 270 between LO and HIGH The heaters will regulate to about 2 5 C of the set temperature once it stabilizes All units are fused for safety The ST10 is available in 100VAC 50 Hz 1 0 amp 115VAC 60 Hz 1 0 amp 220VAC 60 Hz 0 5 amp and 230VAC 50 Hz 0 5 amp The HP10 is available in 100VAC 50 60 Hz 8 amp 115VAC 50 60 Hz 8 amp and 230VAC 50 60 Hz 4 amp The HS10 is available in LOOVAC 50 Hz 8 amp 115VAC 60 Hz 8amp 220VAC 60 Hz 4 amp and 230VAC 50 Hz 4 amp All models are 13 33 cm deep by 9 22 9 cm wide by 3 5 8 9 cm high The HP10s weigh 8 pounds 3 6 kg The ST10 s and HS10 s weigh 10 pounds 4 5 kg All are complete with grounded 3 wire detachable AC line cord for the country of use users manual and full 12 month warranty All are UL CSA and CE compliant DigiLog Stirrers Hot Plates and Stirring Hot Plates The new Digilog series represents state of the art electronic technology applied to simple hot plates and stirrers In effect these units are hybrids of analog and digital units combining features of both to make reliable easy to use units that are priced
30. to better than 0 01 0 254 mm Both units are accurate to 1 over their entire range and will hold a set tempera ture to 1 C The ceramic top will heat to 450 C in about 2 minutes while the aluminum top will heat to 400 C in about 10 minutes Both use 600 watts of heater power They both have platinum RTD sensors under the plate surface for sensing the plate temperature that is tied together with a PID control loop specific for the heater top being used Both have a probe jack on the rear of the unit for an accesso Above is a close up of the membrane switch and display To set a solution temperature press the solution icon and then the UP arrow until the desired temperature is displayed The instru ment does the rest Plate temperature temperature ramping stirring speed and timer are just as simple to set Stainless steel probes are fine for most applications For aggressive solutions Teflon is recommended as long as solution temperatures are below 250 C For higher temperatures with aggressive solutions use the borosilicate glass probe ry probe that is used to sense solution temperatures They both have a specific PID control loop for controlling solutions in a vessel The custom LCD on both displays the plate and probe target and actual temperatures temperature ramp and count down timer with alarm and user settable Auto Off They feature electronic calibration that is set at the factory and traceable t
31. ut ing cords for shakers or tubing for gases They are available in models for 100 115 and 230VAC 50 60 Hz They come for gases They are available in mod els for 100 115 and 230VAC 50 60 Hz They come complete with user s manual 3 wire AC line cord for the country of use and a full 12 month warranty The IN30 measures 15 5 39 4 cm high x 22 25 56 5 cm wide x 18 5 47 cm deep and weighs 40 pounds 18 kg The IN40 measures 28 25 71 75 cm high x 22 25 56 5 cm wide x 18 5 47 cm deep and weighs 46 pounds 20 7 kg All are UL CSA and CE certified complete with users manual 3 wire AC line cord for the country of use and a full 12 month warranty The IN35 measures 15 5 39 4 cm high x 22 25 56 5 cm wide x 18 5 47 cm deep and weighs 40 pounds 18 kg The IN45 measures 28 25 71 75 cm high x 22 25 56 5 cm wide x 18 5 47 cm deep and weighs 46 pounds 20 7 kg All units are UL CSA and CE certified IN35 sample program 10steps 2 cycles 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 Time min The chart above shows a typical temperature time profile that can be stored in memory on an IN35 or IN45 and run at any time 9 Chilling Heating Incubator and Model IN20 Translucent Chilling Heating Incubator The Model IN20 is a unique Peltier driven chilling heating incubator in a number of ways It is fabric
32. warranty The unit measures 6 5 16 5 cm wide x 13 625 34 6 cm deep x 7 17 78 cm high and weighs 6 5 pounds 2 9 kg The unit is UL CSA and CE compliant HPLC Column Chiller He a A z 9eed KO NO bh x A D d very reliable It has a very large chamber measuring 15 5 39 37 cm high x 6 385 16 28 cm wide x 5 125 13 02 cm deep The chamber will easily hold 4 30 cm x 1 columns and a Rheodyne valve Chamber temperature uniformity is 0 52C The door design is The Model CO30 is an HPLC col umn chiller heater with a tempera ture range from 4 0 C or 12 to 16 C below ambient maximum to 70 02 It is accurate to 0 2C readable and settable to 0 1C and can control temperature to 0 1 C with its PID control loop software It is Peltier driven for both heating and cooling making it CFC free It has only 2 moving parts the fans making it unique in that it opens out and down from the top All columns valves and fittings are mounted on the door exposing everything to simple and easy unob structed access It has drains in the door for the valve and in the cham ber floor for spills The unit has a liq uid crystal display used for showing the chamber temperature and the count down timer The unit has a 99 hour count down timer with audible ater and alarm and user settable Auto Off that will shut off the chiller heater after the count down period It has
Download Pdf Manuals
Related Search